Germany: +49 621 776 4411Pepperl+Fuchs Group
Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.
USA: +1 330 486 0001 Singapore: +65 6779 9091
www.pepperl-fuchs.com fa-info@us.pepperl-fuchs.com fa-info@sg.pepperl-fuchs.com
fa-info@de.pepperl-fuchs.com
Inductive sensor NJ5-18GK-SN
5
Release date: 2015-04-25 23:32 Date of issue: 2015-04-26 106643_eng.xml
ATEX 3G (ic )
Instruction Manual electrical apparatus for hazardous areas
Device category 3G (ic) for use in hazardous areas with gas, vapour and mist
Certificate of Compliance PF 13 CERT 2895 X
CE marking 0102
ATEX marking ¬ II 3G Ex ic IIC T6…T1 Gc
The Ex-significant identification is on the enclosed adhesive label
Directive conformity 94/9/EG
Standards EN 60079-0:2012, EN 60079-11:2012 Ignition protection category "ic"
Use is restricted to the following stated conditions
Effective internal capacitance Ci ≤ 120 nF ; A cable length of 10 m is considered.
Effective internal inductance Li ≤ 200 µH ; A cable length of 10 m is considered.
Ge n e r a l The apparatus has to be operated according to the appropriate data in the data sheet
and in this instruction manual. The data stated in the data sheet are restricted by this
operating instruction!
The special conditions must be observed!
Installation, commissioning Laws and/or regulations and standards governing the use or intended usage goal
must be observed. The sensor must only be operated with energy-limited circuits,
which satisfy the requirements of IEC 60079-11. The explosion group depends on
the connected and energy-limited supply circuit.
The adhesive label provided must be affixed in the immediate vicinity of the sensor!
The surface to which the label is applied must be clean, flat and free from grease!
The affixed adhesive label must be readable and durable, taking account of the pos-
sibility of chemical corrosion!
Maintenance No changes can be made to apparatus, which are operated in hazardous areas.
Repairs to these apparatus are not possible.
Special conditions
Maximum permissible ambient temperature TUmax at Ui = 20 V
for Pi=34 mW, Ii=25 mA, T6 70 °C (158 °F)
for Pi=34 mW, Ii=25 mA, T5 85 °C (185 °F)
for Pi=34 mW, Ii=25 mA, T4-T1 100 °C (212 °F)
for Pi=64 mW, Ii=25 mA, T6 69 °C (156.2 °F)
for Pi=64 mW, Ii=25 mA, T5 84 °C (183.2 °F)
for Pi=64 mW, Ii=25 mA, T4-T1 100 °C (212 °F)
for Pi=169 mW, Ii=52 mA, T6 51 °C (123.8 °F)
for Pi=169 mW, Ii=52 mA, T5 66 °C (150.8 °F)
for Pi=169 mW, Ii=52 mA, T4-T1 80 °C (176 °F)
for Pi=242 mW, Ii=76 mA, T6 39 °C (102.2 °F)
for Pi=242 mW, Ii=76 mA, T5 54 °C (129.2 °F)
for Pi=242 mW, Ii=76 mA, T4-T1 61 °C (141.8 °F)
Protection from mechanical danger The sensor must not be mechanically damaged.
When used in the temperature range below -20 °C the sensor should be protected
from knocks by the provision of an additional housing.
Connection parts The connection parts are to be installed, such that a minimum protection class of
IP20 is achieved, in accordance with IEC 60529.