LM4781, LM4781TABD www.ti.com SNAS208A - AUGUST 2003 - REVISED APRIL 2013 LM4781 OvertureTM Audio Power Amplifier Series 3 Channel 35W Audio Power Amplifier with Mute Check for Samples: LM4781, LM4781TABD FEATURES DESCRIPTION * * * * * The LM4781 is a three channel audio amplifier capable of typically delivering 35W per channel of continuous average output power into an 8 load with less than 0.5% THD+N from 20Hz - 20kHz. 1 23 SPiKe Protection Low External Component Count Quiet Fade-In/Out Mute Mode Wide Supply Range: 20V - 70V Signal-to-Noise Ratio 93dB (ref. to PO = 1W) APPLICATIONS * * * * Audio Audio Audio Audio Amplifier Amplifier Amplifier Amplifier for for for for Component Stereo Compact Stereo Self-Powered Speakers High-End and HD TVs KEY SPECIFICATIONS * * * * * * * Output Power/Channel with 0.5% THD+N, 1kHz into 8: 35W (typ) THD+N at 3 x 20W into 8 (20Hz - 20kHz): 0.2% (typ) THD+N at 3 x 20W into 6 (20Hz - 20kHz): 0.3% (typ) THD+N at 3 x 20W into 4 (20Hz - 20kHz): 0.5% (typ) Mute Attenuation: 110dB (typ) PSRR: 85dB (min) Slew Rate: 9V/s (typ) The LM4781 is fully protected utilizing TI's Self Peak Instantaneous Temperature (Ke) (SPiKe) protection circuitry. SPiKe provides a dynamically optimized Safe Operating Area (SOA). SPiKe protection completely safeguards the LM4781's outputs against over-voltage, under-voltage, overloads, shorts to the supplies or GND, thermal runaway and instantaneous temperature peaks. The advanced protection features of the LM4781 places it in a class above discrete and hybrid amplifiers. Each amplifier of the LM4781 has an independent smooth transition fade-in/out mute. The LM4781 can easily be configured for bridge or parallel operation for higher power and bi-amp solutions. 1 2 3 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Overture is a trademark of dcl_owner. All other trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2003-2013, Texas Instruments Incorporated LM4781, LM4781TABD SNAS208A - AUGUST 2003 - REVISED APRIL 2013 www.ti.com Typical Application Figure 1. Typical Audio Amplifier Application Circuit Connection Diagram Figure 2. Plastic TO-220 Package - Top View See Package Number NDM0027A (1) (1) 2 The NDM0027A is a non-isolated package. The package's metal back and any heat sink to which it is mounted are connected to the Vpotential when using only thermal compound. If a mica washer is used in addition to thermal compound, CS (case to sink) is increased, but the heat sink will be electrically isolated from V-. Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4781 LM4781TABD LM4781, LM4781TABD www.ti.com SNAS208A - AUGUST 2003 - REVISED APRIL 2013 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Absolute Maximum Ratings (1) (2) (3) Supply Voltage |V+| + |V-| (No Signal) Supply Voltage |V+| + |V-| (Input Signal) 72V 70V (V+ or V-) and |V+| + |V-| 60V Common Mode Input Voltage Differential Input Voltage (4) 60V Output Current Internally Limited Power Dissipation (5) 125W ESD Susceptability (6) 2.0kV ESD Susceptability (7) 200V Junction Temperature (TJMAX) (8) 150C Soldering Information TA Package (10 seconds) Storage Temperature Thermal Resistance (9) (1) (2) (3) (4) (5) (6) (7) (8) (9) 260C -40C to +150C JA 30C/W JC 0.9C/W Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not ensured for parameters where no limit is given; however, the typical value is a good indication of device performance. All voltages are measured with respect to the ground pins, unless otherwise specified. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and specifications. The Differential Input Voltage Absolute Maximum Rating is based on supply voltages V+ = 30V and V-= - 30V. The maximum power dissipation must be de-rated at elevated temperatures and is dictated by TJMAX, JC, and the ambient temperature TA. The maximum allowable power dissipation is PDMAX = (TJMAX -TA)/JC or the number given in the Absolute Maximum Ratings, whichever is lower. For the LM4781, TJMAX = 150C and the typical JC is 0.9C/W. Refer to the DETERMINING THE CORRECT HEAT SINK section for more information. Human body model, 100pF discharged through a 1.5k resistor. Machine Model: a 220pF - 240pF discharged through all pins. The maximum operating junction temperature is 150C. However, the instantaneous Safe Operating Area temperature is 250C. The NDM0027A is a non-isolated package. The package's metal back and any heat sink to which it is mounted are connected to the Vpotential when using only thermal compound. If a mica washer is used in addition to thermal compound, CS (case to sink) is increased, but the heat sink will be electrically isolated from V-. Operating Ratings (1) (2) (3) TMIN TA TMAX Temperature Range + - 20V VTOTAL 70V Supply Voltage |V | + |V | (1) (2) (3) -20C TA +85C All voltages are measured with respect to the ground pins, unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not ensured for parameters where no limit is given; however, the typical value is a good indication of device performance. Operation is ensured up to 70V; however, distortion may be introduced from SPiKe protection circuitry if proper thermal considerations are not taken into account. Refer to the THERMAL PROTECTION section for more information. Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4781 LM4781TABD Submit Documentation Feedback 3 LM4781, LM4781TABD SNAS208A - AUGUST 2003 - REVISED APRIL 2013 www.ti.com Electrical Characteristics (1) (2) The following specifications apply for V+ = +28V, V- = -28V, IMUTE = -1mA/channel and RL = 8 unless otherwise specified. Limits apply for TA = 25C. Symbol Parameter LM4781 Conditions Typical (3) Limit (4) (5) Units (Limits) |V+| + |V-| Power Supply Voltage (6) GND - V- 9V 18 20 70 V (min) V (max) AM Mute Attenuation IMUTE = 0mA 110 80 dB (min) PO Output Power (RMS) THD+N = 0.5% (max) f = 1kHz |V+| = |V-| = 20V, RL = 4 |V+| = |V-| = 24V, RL = 6 |V+| = |V-| = 28V, RL = 8 25 30 35 20 25 30 W (min) W (min) W (min) THD+N Total Harmonic Distortion + Noise PO = 20W, f = 20Hz - 20kHz AV = 26dB |V+| = |V-| = 20V, RL = 4 |V+| = |V-| = 24V, RL = 6 |V+| = |V-| = 28V, RL = 8 0.5 0.3 0.2 % % % Xtalk Channel Separation (7) PO = 10W, f = 1kHz 70 dB PO = 10W, f = 10kHz 66 dB SR Slew Rate VIN = 1.2VRMS, f = 10kHz square Wave.RL = 2k 9 5 V/s (min) IDD Total Quiescent Power VCM = 0V 75 150 mA (max) Supply Current VO = 0V, IO = 0A VOS Input Offset Voltage VCM = 0V, IO = 0mA 1 10 mV (max) IB Input Bias Current VCM = 0V, IO = 0mA 0.2 1 A (max) IO Output Current Limit |V+| = |V-| = 20V, tON = 10ms 4 3 A (min) |V - VO|, V = 20V, IO = +100mA |VO - V-|, V-= -20V, IO = -100mA 1.5 2.5 4 4 V (max) V (max) V+ = 30V to 10V, V-= -30V VCM = 0V, IO = 0mA 125 85 dB (min) V+ = 30V, V-= -30V to -10V VCM = 0V, IO = 0mA 110 85 dB (min) 110 75 dB (min) 115 80 dB (min) 8 2 MHz (min) 3.0 8 V (max) + Output Dropout Voltage (8) VOD PSRR Power Supply Rejection Ratio (9) + CMRR Common Mode Rejection Ratio (9) V+ = 30V to 10V, V-= -10V to -30V VCM = 20V to -20V, IO = 0mA AVOL Open Loop Voltage Gain |V+| = |V-| = 28V, RL = 2k VO = 20V GBWP Gain Bandwidth Product |V+| = |V-| = 28V, fIN = 100kHz VIN = 50mVRMS eIN Input Noise IHF-A-Weighting Filter, RIN = 600 (Input Referred) (1) (2) (3) (4) (5) (6) (7) (8) (9) 4 All voltages are measured with respect to the ground pins, unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not ensured for parameters where no limit is given; however, the typical value is a good indication of device performance. Typical specifications are measured at 25C and represent the parametric norm. Tested limits are specified to TI's AOQL (Average Outgoing Quality Level). Datasheet min/max specification limits are specified by design, test, or statistical analysis. V- must have at least - 9V at its pin with reference to GND in order for the under-voltage protection circuitry to be disabled. In addition, the voltage differential between V+ and V-must be greater than 14V. Cross talk performance was measured using the demo board shown in the datasheet. PCB layout will affect cross talk. It is recommended that the input and output traces be separated by as much distance as possible. Return ground traces from outputs should also be independent back to single ground point and use as wide of traces as possible. The output dropout voltage is the supply voltage minus the clipping voltage. Refer to the Clipping Voltage vs. Supply Voltage graph in the Typical Performance Characteristics section. DC electrical test. Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4781 LM4781TABD LM4781, LM4781TABD www.ti.com SNAS208A - AUGUST 2003 - REVISED APRIL 2013 Electrical Characteristics(1)(2) (continued) The following specifications apply for V+ = +28V, V- = -28V, IMUTE = -1mA/channel and RL = 8 unless otherwise specified. Limits apply for TA = 25C. Symbol SNR IMD Parameter Conditions Signal-to-Noise Ratio LM4781 Typical (3) Units (Limits) PO = 1WRMS; A-Weighted Filter fIN = 1kHz, RS = 25 93 dB PO = 25WRMS; A-Weighted Filter fIN = 1kHz, RS = 25 107 dB 0.004 0.006 % % 60Hz, 7kHz, 4:1 (SMPTE) 60Hz, 7kHz, 1:1 (SMPTE) Intermodulation Distortion Limit (4) (5) Bridged Amplifier Application Circuit Figure 3. Bridged Amplifier Application Circuit Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4781 LM4781TABD Submit Documentation Feedback 5 LM4781, LM4781TABD SNAS208A - AUGUST 2003 - REVISED APRIL 2013 www.ti.com Parallel Amplifier Application Circuit Figure 4. Parallel Amplifier Application Circuit 6 Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4781 LM4781TABD LM4781, LM4781TABD www.ti.com SNAS208A - AUGUST 2003 - REVISED APRIL 2013 Single Supply Application Circuit Figure 5. Single Supply Amplifier Application Circuit NOTE *Optional components dependent upon specific design requirements. Auxiliary Amplifier Application Circuit Figure 6. Special Audio Amplifier Application Circuit Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4781 LM4781TABD Submit Documentation Feedback 7 LM4781, LM4781TABD SNAS208A - AUGUST 2003 - REVISED APRIL 2013 www.ti.com External Components Description Figure 1, Figure 3, Figure 4, Figure 5, and Figure 6 Components RB Prevents current from entering the amplifier's non-inverting input. This current may pass through to the load during system power down, because of the amplifier's low input impedance when the undervoltage circuitry is off. This phenomenon occurs when the V+ and V-supply voltages are below 1.5V. 2 Ri Inverting input resistance. Along with Rf, sets AC gain. 3 Rf Feedback resistance. Along with Ri, sets AC gain. 4 Rf2 (1) Feedback resistance. Works with Cf and Rf creating a lowpass filter that lowers AC gain at high frequencies. The 3dB point of the pole occurs when: (Rf - Ri)/2 = Rf // [1/(2fcCf) + Rf2] for the Non-Inverting configuration shown in Figure 6. 5 Cf Compensation capacitor. Works with Rf and Rf2 to reduce AC gain at higher frequencies. 6 CC (1) Compensation capacitor. Reduces the gain at higher frequencies to avoid quasi-saturation oscillations of the output transistor. Also suppresses external electromagnetic switching noise created from fluorescent lamps. 7 Ci Feedback capacitor which ensures unity gain at DC. Along with Ri also creates a highpass filter at fc = 1/(2RiCi). 8 CS Provides power supply filtering and bypassing. Refer to the SUPPLY BYPASSING application section for proper placement and selection of bypass capacitors. 9 RV Acts as a volume control by setting the input voltage level. 10 RIN (1) Sets the amplifier's input terminals DC bias point when CIN is present in the circuit. Also works with CIN to create a highpass filter at fC = 1/(2RINCIN). If the value of RIN is too large, oscillations may be observed on the outputs when the inputs are floating. Recommended values are 10k to 47k. Refer to Figure 6. 11 CIN Input capacitor. Prevents the input signal's DC offsets from being passed onto the amplifier's inputs. 12 RSN Works with CSN to stabilize the output stage by creating a pole that reduces high frequency instabilities. 13 CSN Works with RSN to stabilize the output stage by creating a pole that reduces high frequency instabilities. The pole is set at fC = 1/(2RSNCSN). Refer to Figure 6. 14 L (1) 15 R (1) Provides high impedance at high frequencies so that R may decouple a highly capacitive load and reduce the Q of the series resonant circuit. Also provides a low impedance at low frequencies to short out R and pass audio signals to the load. Refer to Figure 6. 16 RA Provides DC voltage biasing for the transistor Q1 in single supply operation. 17 CA Provides bias filtering for single supply operation. 18 RINP Limits the voltage difference between the amplifier's inputs for single supply operation. Refer to the CLICKS AND POPS application section for a more detailed explanation of the function of RINP. 19 RBI Provides input bias current for single supply operation. Refer to the CLICKS AND POPS application section for a more detailed explanation of the function of RBI. 20 RE Establishes a fixed DC current for the transistor Q1 in single supply operation. This resistor stabilizes the halfsupply point along with CA. 21 RM Mute resistance set up to allow 0.5mA to be drawn from each MUTE pin to turn the muting function off. RM is calculated using: RM (|VEE| - 2.6V)/l where l 0.5mA. Refer to the Mute Attenuation vs Mute Current curves in the Typical Performance Characteristics section. 22 CM Mute capacitance set up to create a large time constant for turn-on and turn-off muting. 23 S1 Mute switch. When open or switched to GND, the amplifier will be in mute mode. 24 ROUT Reduces current flow between outputs that are caused by Gain or DC offset differences between the amplifiers. (1) 8 Functional Description 1 (1) (1) (1) (1) (1) (1) (1) Optional components dependent upon specific design requirements. Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4781 LM4781TABD LM4781, LM4781TABD www.ti.com SNAS208A - AUGUST 2003 - REVISED APRIL 2013 Optional External Component Interaction Although the optional external components have specific desired functions that are designed to reduce the bandwidth and eliminate unwanted high frequency oscillations they may cause certain undesirable effects when they interact. Interaction may occur for components whose reactances are in close proximity to one another. One example would be the coupling capacitor, CC, and the compensation capacitor, Cf. These two components act as low impedances to certain frequencies which will couple signals from the input to the output. Please take careful note of basic amplifier component functionality when designing in these components. The optional external components shown in Figure 5 and Figure 6 and described above are applicable in both single and split voltage supply configurations. Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4781 LM4781TABD Submit Documentation Feedback 9 LM4781, LM4781TABD SNAS208A - AUGUST 2003 - REVISED APRIL 2013 www.ti.com Typical Performance Characteristics 10 THD+N vs Frequency 20V, POUT = 1W & 20W/Channel RL = 4, 80kHz BW THD+N vs Frequency 24V, POUT = 1W & 20W/Channel RL = 6, 80kHz BW Figure 7. Figure 8. THD+N vs Frequency 28V, POUT = 1W & 20W/Channel RL = 8, 80kHz BW THD+N vs Output Power/Channel 20V, RL = 4, 80kHz BW Figure 9. Figure 10. THD+N vs Output Power/Channel 24V, RL = 6, 80kHz BW THD+N vs Output Power/Channel 28V, RL = 8, 80kHz BW Figure 11. Figure 12. Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4781 LM4781TABD LM4781, LM4781TABD www.ti.com SNAS208A - AUGUST 2003 - REVISED APRIL 2013 Typical Performance Characteristics (continued) Output Power/Channel vs Supply Voltage f = 1kHz, RL = 4, 80kHz BW Output Power/Channel vs Supply Voltage f = 1kHz, RL = 6, 80kHz BW Figure 13. Figure 14. Output Power/Channel vs Supply Voltage f = 1kHz, RL = 8, 80kHz BW Total Power Dissipation vs Output Power/Channel 1% THD (max), RL = 4, 80kHz BW Figure 15. Figure 16. Total Power Dissipation vs Output Power/Channel 1% THD (max), RL = 6, 80kHz BW Total Power Dissipation vs Output Power/Channel 1% THD (max), RL = 8, 80kHz BW Figure 17. Figure 18. Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4781 LM4781TABD Submit Documentation Feedback 11 LM4781, LM4781TABD SNAS208A - AUGUST 2003 - REVISED APRIL 2013 www.ti.com Typical Performance Characteristics (continued) 12 Crosstalk vs Frequency 20V, POUT = 10W, RL = 4, 80kHz BW Crosstalk vs Frequency 28V, POUT = 10W, RL = 8, 80kHz BW Figure 19. Figure 20. Two Channels On Crosstalk vs Frequency 20V, POUT = 10W, RL = 4, 80kHz BW Two Channels On Crosstalk vs Frequency 28V, POUT = 10W, RL = 8, 80kHz BW Figure 21. Figure 22. Mute Attenuation vs Mute Pin Current POUT = 10W/Channel Supply Current vs Supply Voltage Figure 23. Figure 24. Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4781 LM4781TABD LM4781, LM4781TABD www.ti.com SNAS208A - AUGUST 2003 - REVISED APRIL 2013 Typical Performance Characteristics (continued) Large Signal Response Power Supply Rejection Ratio Figure 25. Figure 26. Common-Mode Rejection Ratio Open Loop Frequency Response Figure 27. Figure 28. Clipping Voltage vs Supply Voltage THD+N vs Frequency 20V, POUT = 1W & 25W, Chs 1&3 in Bridge Mode (Note17), RL = 8, 80kHz BW Figure 29. Figure 30. Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4781 LM4781TABD Submit Documentation Feedback 13 LM4781, LM4781TABD SNAS208A - AUGUST 2003 - REVISED APRIL 2013 www.ti.com Typical Performance Characteristics (continued) 14 THD+N vs Frequency 28V, POUT = 1W & 35W, Chs 1&3 in Parallel Mode (Note18), RL = 4, 80kHz BW THD+N vs Frequency 24V, POUT = 1W & 45W, All Chs in Parallel Mode (Note18), RL = 2, 80kHz BW Figure 31. Figure 32. THD+N vs Output Power 20V, Chs 1&3 in Bridge Mode (Note17), RL = 8, 80kHz BW THD+N vs Output Power 28V, Chs 1&3 in Parallel Mode (Note18), RL = 4, 80kHz BW Figure 33. Figure 34. THD+N vs Output Power 24V, All Chs in Parallel Mode (Note18), RL = 2, 80kHz BW Output Power vs Supply Voltage Chs 1&3 in Bridge Mode (Note17), f = 1kHz, RL = 8, 80kHz BW Figure 35. Figure 36. Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4781 LM4781TABD LM4781, LM4781TABD www.ti.com SNAS208A - AUGUST 2003 - REVISED APRIL 2013 Typical Performance Characteristics (continued) Output Power vs Supply Voltage Chs 1&3 in Parallel Mode (Note18), f = 1kHz, RL = 4, 80kHz BW Output Power vs Supply Voltage All Chs in Parallel Mode (Note18), f = 1kHz, RL = 2, 80kHz BW Figure 37. Figure 38. Safe Area SpiKe Protection Response Figure 39. Figure 40. (1) Bridge mode graphs were taken using the demo board and inverting the signal to the channel B input. (2) Parallel mode graphs were taken using the demo board connecting each output through a 0.1/3W resistor to the load. Frequency Response of Demo Board POUT = 10W/Channel = 0dB, RIN = 47k RL = 8, No Filters Figure 41. Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4781 LM4781TABD Submit Documentation Feedback 15 LM4781, LM4781TABD SNAS208A - AUGUST 2003 - REVISED APRIL 2013 www.ti.com APPLICATION INFORMATION MUTE MODE The muting function allows the user to mute the amplifier. This can be accomplished as shown in the Typical Application Circuit. The resistor RM is chosen with reference to the negative supply voltage and is used in conjunction with a switch. The switch, when opened or switched to GND, cuts off the current flow from the MUTE pins to -VEE, thus placing the LM4781 into mute mode. Refer to the Mute Attenuation vs Mute Current curves in the Typical Performance Characteristics section for values of attenuation per current out of each MUTE pin. The resistance RM is calculated by the following equation: RM (|-VEE| - 2.6V) / IMUTE Where * IMUTE 0.5mA for each MUTE pin. (1) The MUTE pins can be tied together so that only one resistor is required for the mute function. The mute resistor value must be chosen so that a minimum of 1.5mA is pulled through the resistor RM. This ensures that each amplifier is fully operational. Taking into account supply line fluctuations, it is a good idea to pull out 1mA per MUTE pin or 3mA total if all pins are tied together. A turn-on MUTE or soft start circuit may also be used during power up. A simple circuit like the one shown below may be used. The RC combination of CM and RM1 may cause the voltage at point A to change more slowly than the -VEE supply voltage. Until the voltage at point A is low enough to have 0.5mA of current per MUTE pin flow through RM2, the IC will be in mute mode. The series combination of RM1 and RM2 needs to satisfy Equation 1 above for all operating voltages or mute mode may be activated during normal operation. For a longer turn-on mute time, a larger time constant, = RC = RM1CM (sec), is needed. For the values show above and with the MUTE pins tied together, the LM4781 will enter play mode when the voltage at point A is -25.1V. The voltage at point A is found with Equation 2 below. VA(t) = (Vf - VO)e-t/ (Volts) where * * * * t = time (sec) = RC (sec) Vo = Voltage on C at t = 0 (Volts) Vf = Final voltage, -VEE in this circuit (Volts) (2) UNDER-VOLTAGE PROTECTION Upon system power-up, the under-voltage protection circuitry allows the power supplies and their corresponding capacitors to come up close to their full values before turning on the LM4781. Since the supplies have essentially settled to their final value, no DC output spikes occur. At power down, the outputs of the LM4781 are forced to ground before the power supply voltages fully decay preventing transients on the output. OVER-VOLTAGE PROTECTION The LM4781 contains over-voltage protection circuitry that limits the output current while also providing voltage clamping. The clamp does not, however, use internal clamping diodes. The clamping effect is quite the same because the output transistors are designed to work alternately by sinking large current spikes. 16 Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4781 LM4781TABD LM4781, LM4781TABD www.ti.com SNAS208A - AUGUST 2003 - REVISED APRIL 2013 SPiKe PROTECTION The LM4781 is protected from instantaneous peak-temperature stressing of the power transistor array. The Safe Operating graph in the Typical Performance Characteristics section shows the area of device operation where SPiKe Protection Circuitry is not enabled. The SPiKe Protection Response waveform graph shows the waveform distortion when SPiKe is enabled. Please refer to AN-898 for more detailed information. THERMAL PROTECTION The LM4781 has a sophisticated thermal protection scheme to prevent long-term thermal stress of the device. When the temperature on the die exceeds 150C, the LM4781 shuts down. It starts operating again when the die temperature drops to about 145C, but if the temperature again begins to rise, shutdown will occur again above 150C. Therefore, the device is allowed to heat up to a relatively high temperature if the fault condition is temporary, but a sustained fault will cause the device to cycle in a Schmitt Trigger fashion between the thermal shutdown temperature limits of 150C and 145C. This greatly reduces the stress imposed on the IC by thermal cycling, which in turn improves its reliability under sustained fault conditions. Since the die temperature is directly dependent upon the heat sink used, the heat sink should be chosen so that thermal shutdown is not activated during normal operation. Using the best heat sink possible within the cost and space constraints of the system will improve the long-term reliability of any power semiconductor device, as discussed in the DETERMINING THE CORRECT HEAT SINK section. DETERMlNlNG MAXIMUM POWER DISSIPATION Power dissipation within the integrated circuit package is a very important parameter requiring a thorough understanding if optimum power output is to be obtained. An incorrect maximum power dissipation calculation may result in inadequate heat sinking causing thermal shutdown and thus limiting the output power. Equation 3 shows the theoretical maximum power dissipation point for each amplifier in a single-ended configuration where VCC is the total supply voltage. PDMAX = (VCC)2 / 22RL (3) Thus by knowing the total supply voltage and rated output load, the maximum power dissipation point can be calculated. The package dissipation is three times the number which results from Equation 3 since there are three amplifiers in each LM4781. Refer to the graphs of Power Dissipation versus Output Power in the Typical Performance Characteristics section which show the actual full range of power dissipation not just the maximum theoretical point that results from Equation 3. DETERMINING THE CORRECT HEAT SINK The choice of a heat sink for a high-power audio amplifier is made entirely to keep the die temperature at a level such that the thermal protection circuitry is not activated under normal circumstances. The thermal resistance from the die to the outside air, JA (junction to ambient), is a combination of three thermal resistances, JC (junction to case), CS (case to sink), and SA (sink to ambient). The thermal resistance, JC (junction to case), of the LM4781T is 0.9C/W. Using Thermalloy Thermacote thermal compound, the thermal resistance, CS (case to sink), is about 0.2C/W. Since convection heat flow (power dissipation) is analogous to current flow, thermal resistance is analogous to electrical resistance, and temperature drops are analogous to voltage drops, the power dissipation out of the LM4781 is equal to the following: PDMAX = (TJMAX-TAMB) / JA where * * * TJMAX = 150C TAMB is the system ambient temperature JA = JC + CS + SA Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4781 LM4781TABD (4) Submit Documentation Feedback 17 LM4781, LM4781TABD SNAS208A - AUGUST 2003 - REVISED APRIL 2013 www.ti.com Once the maximum package power dissipation has been calculated using Equation 3, the maximum thermal resistance, SA, (heat sink to ambient) in C/W for a heat sink can be calculated. This calculation is made using Equation 5 which is derived by solving for SA in Equation 4. SA = [(TJMAX-TAMB)-PDMAX(JC +CS)] / PDMAX (5) Again it must be noted that the value of SA is dependent upon the system designer's amplifier requirements. If the ambient temperature that the audio amplifier is to be working under is higher than 25C, then the thermal resistance for the heat sink, given all other things are equal, will need to be smaller. SUPPLY BYPASSING The LM4781 has excellent power supply rejection and does not require a regulated supply. However, to improve system performance as well as eliminate possible oscillations, the LM4781 should have its supply leads bypassed with low-inductance capacitors having short leads that are located close to the package terminals. Inadequate power supply bypassing will manifest itself by a low frequency oscillation known as "motorboating" or by high frequency instabilities. These instabilities can be eliminated through multiple bypassing utilizing a large tantalum or electrolytic capacitor (10F or larger) which is used to absorb low frequency variations and a small ceramic capacitor (0.1F) to prevent any high frequency feedback through the power supply lines. If adequate bypassing is not provided, the current in the supply leads which is a rectified component of the load current may be fed back into internal circuitry. This signal causes distortion at high frequencies requiring that the supplies be bypassed at the package terminals with an electrolytic capacitor of 470F or more. BRIDGED AMPLIFIER APPLICATION The LM4781 has three operational amplifiers internally, allowing for a few different amplifier configurations. One of these configurations is referred to as "bridged mode" and involves driving the load differentially through two of the LM4781's outputs. This configuration is shown in Figure 3. Bridged mode operation is different from the classical single-ended amplifier configuration where one side of its load is connected to ground. A bridge amplifier design has a distinct advantage over the single-ended configuration, as it provides differential drive to the load, thus doubling output swing for a specified supply voltage. Theoretically, four times the output power is possible as compared to a single-ended amplifier under the same conditions. This increase in attainable output power assumes that the amplifier is not current limited or clipped. A direct consequence of the increased power delivered to the load by a bridge amplifier is an increase in internal power dissipation. For each operational amplifier in a bridge configuration, the internal power dissipation will increase by a factor of two over the single ended dissipation. Using Equation 3 the load impedance should be divided by a factor of two to find the maximum power dissipation point for each amplifier in a bridge configuration. In the case of an 8 load in a bridge configuration, the value used for RL in DETERMlNlNG MAXIMUM POWER DISSIPATION would be 4 for each amplifier in the bridge. When using two of the amplifiers of the LM4781 in bridge mode, the third amplifier should have a load impedance equal to or higher than the equivalent impedance seen by each of the bridged amplifiers. In the example above where the bridge load is 8 and each amplifier in the bridge sees a load value of 4 then the third amplifier should also have a 4 load impedance or higher. Using a lower load impedance on the third amplifier will result in higher power dissipation in the third amplifier than the other two amplifiers and may result in unwanted activation of thermal shut down on the third amplifier. Once the impedance seen by each amplifier is known then Equation 3 can be used to calculated the value of PDMAX for each amplifier. The PDMAX of the IC package is found by adding up the power dissipation for each amplifier within the IC package. This value of PDMAX can be used to calculate the correct size heat sink for a bridged amplifier application. Since the internal dissipation for a given power supply and load is increased by using bridged-mode, the heatsink's SA will have to decrease accordingly as shown by Equation 5. Refer to the section, DETERMINING THE CORRECT HEAT SINK for a more detailed discussion of proper heat sinking for a given application. 18 Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4781 LM4781TABD LM4781, LM4781TABD www.ti.com SNAS208A - AUGUST 2003 - REVISED APRIL 2013 PARALLEL AMPLIFIER APPLICATION Parallel configuration is normally used when higher output current is needed for driving lower impedance loads (i.e. 4 or lower) to obtain higher output power levels. As shown in Figure 4 , the parallel amplifier configuration consist of designing the amplifiers in the IC to have identical gain, connecting the inputs in parallel and then connecting the outputs in parallel through a small external output resistor. Any number of amplifiers can be connected in parallel to obtain the needed output current or to divide the power dissipation across multiple IC packages. Ideally, each amplifier shares the output current equally. Due to slight differences in gain the current sharing will not be equal among all channels. If current is not shared equally among all channels then the power dissipation will also not be equal among all channels. It is recommended that 0.1% tolerance resistors be used to set the gain (Ri and Rf) for a minimal amount of difference in current sharing. When operating two or more amplifiers in parallel mode the impedance seen by each amplifier is equal to the total load impedance multiplied by the number of amplifiers driving the load in parallel as shown by Equation 6 below: RL(parallel) = RL(total) * Number of amplifiers (6) Once the impedance seen by each amplifier in the parallel configuration is known then Equation 3 can be used with this calculated impedance to find the amount of power dissipation for each amplifier. Total power dissipation (PDMAX) within an IC package is found by adding up the power dissipation for each amplifier in the IC package. Using the calculated PDMAX the correct heat sink size can be determined. Refer to the section, DETERMINING THE CORRECT HEAT SINK, for more information and detailed discussion of proper heat sinking. If only two amplifiers of the LM4781 are used in parallel mode then the third amplifier should have a load impedance equal to or higher than the equivalent impedance seen by each of the amplifiers in parallel mode. Having the same load impedance on all amplifiers means that the power dissipation in each amplifier will be equal. Using a lower load impedance on the third amplifier will result in higher power dissipation in the third amplifier than the other two amplifiers and may result in unwanted activation of thermal shut down on the third amplifier. Having a higher impedance on the third amplifier than the equivalent impedance on the two amplifiers in parallel will reduce total IC package power dissipation reducing the heat sink size requirement. BI-AMP AND TRI-AMP APPLICATIONS Bi-amping is the practice of using two different amplifiers to power the individual drivers in a speaker enclosure. For example, a two-way speaker enclosure might have a tweeter and a subwoofer. One amplifier would drive the tweeter and another would drive the subwoofer. One advantage is that the gain of each amplifier can be adjusted for the different driver sensitivities. Another advantage is the crossover can be designed before the amplifier stages with low cost op amps instead of large passive components. With the crossover before the amplifier stages no power is wasted in the passive crossover as each individual amplifier provides the correct frequencies for the driver. Tri-Amping is using three different amplifier stages in the same way bi-amping is done. Bi-amping can also be done on a three-way speaker design by using one amplifier for the subwoofer and another for the midrange and tweeter. The LM4781 is perfectly suited for bi-amp or tri-amp applications with it's three amplifiers. Two of the amplifiers can be configured for bridge or parallel mode to drive a subwoofer with the third amplifier driving the tweeter or tweeter and midrange. An example would be to use a 4 subwoofer and 8 tweeter/midrange with the LM4781 in parallel and single-ended modes. Each amplifier would see an 8 load but the subwoofer would have twice the output power as the tweeter/midrange. The gain of each amplifier may also be adjusted for the desired response. Using the LM4781 in a tri-amp configuration would allow the gain of each amplifier to be adjusted to achieve the desired speaker response. SINGLE-SUPPLY AMPLIFIER APPLICATION The typical application of the LM4781 is a split supply amplifier. But as shown in Figure 5, the LM4781 can also be used in a single power supply configuration. This involves using some external components to create a halfsupply bias which is used as the reference for the inputs and outputs. Thus, the signal will swing around halfsupply much like it swings around ground in a split-supply application. Along with proper circuit biasing, a few other considerations must be accounted for to take advantage of all of the LM4781 functions, like the mute function. Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4781 LM4781TABD Submit Documentation Feedback 19 LM4781, LM4781TABD SNAS208A - AUGUST 2003 - REVISED APRIL 2013 www.ti.com CLICKS AND POPS In the typical application of the LM4781 as a split-supply audio power amplifier, the IC exhibits excellent "click" and "pop" performance when utilizing the mute mode. In addition, the device employs Under-Voltage Protection, which eliminates unwanted power-up and power-down transients. The basis for these functions are a stable and constant half-supply potential. In a split-supply application, ground is the stable half-supply potential. But in a single-supply application, the half-supply needs to charge up at the same rate as the supply rail, VCC. This makes the task of attaining a clickless and popless turn-on more challenging. Any uneven charging of the amplifier inputs will result in output clicks and pops due to the differential input topology of the LM4781. To achieve a transient free power-up and power-down, the voltage seen at the input terminals should be ideally the same. Such a signal will be common-mode in nature, and will be rejected by the LM4781. In Figure 5, the resistor RINP serves to keep the inputs at the same potential by limiting the voltage difference possible between the two nodes. This should significantly reduce any type of turn-on pop, due to an uneven charging of the amplifier inputs. This charging is based on a specific application loading and thus, the system designer may need to adjust these values for optimal performance. As shown in Figure 5, the resistors labeled RBI help bias up the LM4781 off the half-supply node at the emitter of the 2N3904. But due to the input and output coupling capacitors in the circuit, along with the negative feedback, there are two different values of RBI, namely 10k and 200k. These resistors bring up the inputs at the same rate resulting in a popless turn-on. Adjusting these resistors values slightly may reduce pops resulting from power supplies that ramp extremely quick or exhibit overshoot during system turn-on. PROPER SELECTION OF EXTERNAL COMPONENTS Proper selection of external components is required to meet the design targets of an application. The choice of external component values that will affect gain and low frequency response are discussed below. The gain of each amplifier is set by resistors Rf and Ri for the non-inverting configuration shown in Figure 1. The gain is found by Equation 7 below: AV = 1 + Rf / Ri (V/V) (7) For best noise performance, lower values of resistors are used. A value of 1k is commonly used for Ri and then setting the value of Rf for the desired gain. For the LM4781 the gain should be set no lower than 10V/V and no higher than 50V/V. Gain settings below 10V/V may experience instability and using the LM4781 for gains higher than 50V/V will see an increase in noise and THD. The combination of Ri with Ci (see Figure 1) creates a high pass filter. The low frequency response is determined by these two components. The -3dB point can be found from Equation 8 shown below: fi = 1 / (2RiCi) (Hz) (8) If an input coupling capacitor is used to block DC from the inputs as shown in Figure 6, there will be another high pass filter created with the combination of CIN and RIN. When using a input coupling capacitor RIN is needed to set the DC bias point on the amplifier's input terminal. The resulting -3dB frequency response due to the combination of CIN and RIN can be found from Equation 9 shown below: fIN = 1 / (2RINCIN) (Hz) (9) With large values of RIN oscillations may be observed on the outputs when the inputs are left floating. Decreasing the value of RIN or not letting the inputs float will remove the oscillations. If the value of RIN is decreased then the value of CIN will need to increase in order to maintain the same -3dB frequency response. HIGH PERFORMANCE CONSIDERATIONS Using low cost electrolytic capacitors in the signal path such as CIN and Ci (see Figure 1, Figure 3, Figure 4, Figure 5, and Figure 6) will result in very good performance. However, electrolytic capacitors are less linear than other premium capacitors. Higher THD+N performance may be obtained by using high quality polypropylene capacitors in the signal path. A more cost effective solution may be the use of smaller value premium capacitors in parallel with the larger electrolytic capacitors. This will maintain signal quality in the upper audio band where any degradation is most noticeable while also coupling in the signals in the lower audio band for good bass response. Distortion is introduced as the audio signal approaches the lower -3dB point, determined as discussed in the section above. By using larger values of capacitors such that the -3dB point is well outside of the audio band will reduce this distortion and improve THD+N performance. 20 Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4781 LM4781TABD LM4781, LM4781TABD www.ti.com SNAS208A - AUGUST 2003 - REVISED APRIL 2013 Increasing the value of the large supply bypass capacitors will improve burst power output. The larger the supply bypass capacitors the higher the output pulse current without supply droop increasing the peak output power. This will also increase the headroom of the amplifier and reduce THD. SIGNAL-TO-NOISE RATIO In the measurement of the signal-to-noise ratio, misinterpretations of the numbers actually measured are common. One amplifier may sound much quieter than another, but due to improper testing techniques, they appear equal in measurements. This is often the case when comparing integrated circuit designs to discrete amplifier designs. Discrete transistor amps often "run out of gain" at high frequencies and therefore have small bandwidths to noise as indicated below. Integrated circuits have additional open loop gain allowing additional feedback loop gain in order to lower harmonic distortion and improve frequency response. It is this additional bandwidth that can lead to erroneous signal-to-noise measurements if not considered during the measurement process. In the typical example above, the difference in bandwidth appears small on a log scale but the factor of 10in bandwidth, (200kHz to 2MHz) can result in a 10dB theoretical difference in the signal-to-noise ratio (white noise is proportional to the square root of the bandwidth in a system). In comparing audio amplifiers it is necessary to measure the magnitude of noise in the audible bandwidth by using a "weighting" filter (see Note below). A "weighting" filter alters the frequency response in order to compensate for the average human ear's sensitivity to the frequency spectra. The weighting filters at the same time provide the bandwidth limiting as discussed in the previous paragraph. NOTE CCIR/ARM: A Practical Noise Measurement Method; by Ray Dolby, David Robinson and Kenneth Gundry, AES Preprint No. 1353 (F-3). In addition to noise filtering, differing meter types give different noise readings. Meter responses include: 1. RMS reading, 2. average responding, 3. peak reading, and 4. quasi peak reading. Although theoretical noise analysis is derived using true RMS based calculations, most actual measurements are taken with ARM (Average Responding Meter) test equipment. Typical signal-to-noise figures are listed for an A-weighted filter which is commonly used in the measurement of noise. The shape of all weighting filters is similar, with the peak of the curve usually occurring in the 3kHz-7kHz region. LEAD INDUCTANCE Power op amps are sensitive to inductance in the output leads, particularly with heavy capacitive loading. Feedback to the input should be taken directly from the output terminal, minimizing common inductance with the load. Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4781 LM4781TABD Submit Documentation Feedback 21 LM4781, LM4781TABD SNAS208A - AUGUST 2003 - REVISED APRIL 2013 www.ti.com Lead inductance can also cause voltage surges on the supplies. With long leads to the power supply, energy is stored in the lead inductance when the output is shorted. This energy can be dumped back into the supply bypass capacitors when the short is removed. The magnitude of this transient is reduced by increasing the size of the bypass capacitor near the IC. With at least a 20F local bypass, these voltage surges are important only if the lead length exceeds a couple feet (>1H lead inductance). Twisting together the supply and ground leads minimizes the effect. PHYSICAL IC MOUNTING CONSIDERATIONS Mounting of the package to a heat sink must be done such that there is sufficient pressure from the mounting screws to insure good contact with the heat sink for efficient heat flow. Over tightening the mounting screws will cause the package to warp reducing contact area with the heat sink. Less contact with the heat sink will increase the thermal resistance from the package case to the heat sink (CS) resulting in higher operating die temperatures and possible unwanted thermal shut down activation. Extreme over tightening of the mounting screws will cause severe physical stress resulting in cracked die and catastrophic IC failure. The recommended mounting screw size is M3 with a maximum torque of 50 N-cm. Additionally, it is best to use washers under the screws to distribute the force over a wider area or a screw with a wide flat head. To further distribute the mounting force a solid mounting bar in front of the package and secured in place with the two mounting screws may be used. Other mounting options include a spring clip. If the package is secured with pressure on the front of the package the maximum pressure on the molded plastic should not exceed 150N/mm2. Additionally, if the mounting screws are used to force the package into correct alignment with the heat sink, package stress will be increased. This increase in package stress will result in reduced contact area with the heat sink increasing die operating temperature and possible catastrophic IC failure. LAYOUT, GROUND LOOPS AND STABILITY The LM4781 is designed to be stable when operated at a closed-loop gain of 10 or greater, but as with any other high-current amplifier, the LM4781 can be made to oscillate under certain conditions. These oscillations usually involve printed circuit board layout or output/input coupling issues. When designing a layout, it is important to return the load ground, the output compensation ground, and the low level (feedback and input) grounds to the circuit board common ground point through separate paths. Otherwise, large currents flowing along a ground conductor will generate voltages on the conductor which can effectively act as signals at the input, resulting in high frequency oscillation or excessive distortion. It is advisable to keep the output compensation components and the 0.1F supply decoupling capacitors as close as possible to the LM4781 to reduce the effects of PCB trace resistance and inductance. For the same reason, the ground return paths should be as short as possible. In general, with fast, high-current circuitry, all sorts of problems can arise from improper grounding which again can be avoided by returning all grounds separately to a common point. Without isolating the ground signals and returning the grounds to a common point, ground loops may occur. "Ground Loop" is the term used to describe situations occurring in ground systems where a difference in potential exists between two ground points. Ideally a ground is a ground, but unfortunately, in order for this to be true, ground conductors with zero resistance are necessary. Since real world ground leads possess finite resistance, currents running through them will cause finite voltage drops to exist. If two ground return lines tie into the same path at different points there will be a voltage drop between them. The first figure below, in Figure 42, shows a common ground example where the positive input ground and the load ground are returned to the supply ground point via the same wire. The addition of the finite wire resistance, R2, results in a voltage difference between the two points as shown below. 22 Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4781 LM4781TABD LM4781, LM4781TABD www.ti.com SNAS208A - AUGUST 2003 - REVISED APRIL 2013 Figure 42. The load current IL will be much larger than input bias current II, thus V1 will follow the output voltage directly, i.e. in phase. Therefore the voltage appearing at the non-inverting input is effectively positive feedback and the circuit may oscillate. If there was only one device to worry about then the values of R1 and R2 would probably be small enough to be ignored; however, several devices normally comprise a total system. Any ground return of a separate device, whose output is in phase, can feedback in a similar manner and cause instabilities. Out of phase ground loops also are troublesome, causing unexpected gain and phase errors. The solution to most ground loop problems is to always use a single-point ground system, although this is sometimes impractical. The third figure above, in Figure 42, is an example of a single-point ground system. The single-point ground concept should be applied rigorously to all components and all circuits when possible. Violations of single-point grounding are most common among printed circuit board designs, since the circuit is surrounded by large ground areas which invite the temptation to run a device to the closest ground spot. As a final rule, make all ground returns low resistance and low inductance by using large wire and wide traces. Occasionally, current in the output leads (which function as antennas) can be coupled through the air to the amplifier input, resulting in high-frequency oscillation. This normally happens when the source impedance is high or the input leads are long. The problem can be eliminated by placing a small capacitor, CC, (on the order of 50pF to 500pF) across the LM4781 input terminals. Refer to the External Components Description section relating to component interaction with Cf. REACTIVE LOADING It is hard for most power amplifiers to drive highly capacitive loads very effectively and normally results in oscillations or ringing on the square wave response. If the output of the LM4781 is connected directly to a capacitor with no series resistance, the square wave response will exhibit ringing if the capacitance is greater than about 0.2F. If highly capacitive loads are expected due to long speaker cables, a method commonly employed to protect amplifiers from low impedances at high frequencies is to couple to the load through a 10 resistor in parallel with a 0.7H inductor. The inductor-resistor combination as shown in the Figure 6 isolates the feedback amplifier from the load by providing high output impedance at high frequencies thus allowing the 10 resistor to decouple the capacitive load and reduce the Q of the series resonant circuit. The LR combination also provides low output impedance at low frequencies thus shorting out the 10 resistor and allowing the amplifier to drive the series RC load (large capacitive load due to long speaker cables) directly. Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4781 LM4781TABD Submit Documentation Feedback 23 LM4781, LM4781TABD SNAS208A - AUGUST 2003 - REVISED APRIL 2013 www.ti.com INVERTING AMPLIFIER APPLICATION The inverting amplifier configuration may be used instead of the more common non-inverting amplifier configuration shown in Figure 1. The inverting amplifier can have better THD+N performance and eliminates the need for a large capacitor (Ci) reducing cost and space requirements. The values show in Figure 43 are only one example of an amplifier with a gain of 20V/V (Gain = -Rf/Ri). For different resistor values, the value of RB should be eqaul to the parallel combination of Rf and Ri. If the DC blocking input capacitor (CIN) is used as shown, the lower -3dB point is found using Equation 9 as discussed in the PROPER SELECTION OF EXTERNAL COMPONENTS section. Figure 43. Inverting Amplifier Application Circuit 24 Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4781 LM4781TABD LM4781, LM4781TABD www.ti.com SNAS208A - AUGUST 2003 - REVISED APRIL 2013 Figure 44. Reference PCB Schematic LM4781 REFERENCE BOARD ARTWORK Figure 45. Composite Layer Figure 46. Silk Layer Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4781 LM4781TABD Submit Documentation Feedback 25 LM4781, LM4781TABD SNAS208A - AUGUST 2003 - REVISED APRIL 2013 www.ti.com Figure 47. Top Layer Figure 48. Bottom Layer Table 1. Bill Of Materials for Reference PCB 26 Symbol Value Tolerance Type/Description RIN1, RIN2, RIN3 33k 5% 1/4 Watt RB1, RB2, RB3 1k 1% 1/4 Watt RF1, RF2, RF3 20k 1% 1/4 Watt Ri1, Ri2, Ri3 1k 1% 1/4 Watt RSN1, RSN2, RSN3 4.7 5% 1/4 Watt RG 2.7 5% 1/4 Watt RM 5.6k 5% 1/4 Watt CIN1, CIN2, CIN3 1F 10% Metallized Polyester Film Ci1, Ci2, Ci3 47F 20% Electrolytic Radial / 50V CSN1, CSN2, CSN3 0.1F 20% Monolithic Ceramic CS1, CS2 0.1F 20% Monolithic Ceramic CS3, CS4 10F 20% Electrolytic Radial / 50V CS5, CS6 2,200F 20% Electrolytic Radial / 50V S1 SPDT (on-on) Switch J1, J2, J3 Non-Switched PC Mount RCA Jack J5, J7, J9, J11 PCB Banana Jack - BLACK J4, J6, J8, J10, J12 PCB Banana Jack - RED U1 27 lead TO-220 Power Socket with push release lever or LM4781 IC Submit Documentation Feedback Comment Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4781 LM4781TABD LM4781, LM4781TABD www.ti.com SNAS208A - AUGUST 2003 - REVISED APRIL 2013 REVISION HISTORY Changes from Original (April 2013) to Revision A * Page Changed layout of National Data Sheet to TI format .......................................................................................................... 26 Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4781 LM4781TABD Submit Documentation Feedback 27 PACKAGE OPTION ADDENDUM www.ti.com 16-Oct-2015 PACKAGING INFORMATION Orderable Device Status (1) LM4781TA/NOPB LIFEBUY Package Type Package Pins Package Drawing Qty TO-220 NDM 27 15 Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Green (RoHS & no Sb/Br) CU SN Level-1-NA-UNLIM Op Temp (C) Device Marking (4/5) -20 to 85 L4781TA (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 16-Oct-2015 Addendum-Page 2 MECHANICAL DATA NDM0027A TA27A (Rev B) www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2016, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LM4781TA LM4781TABD LM4781TABD/NOPB