___________________ Overview 1 ___________________ Safety instructions SITOP power supply Description, device design, 2 ___________________ dimension drawing ___________________ 3 Mounting/removal LOGO!Power Manual Mounting position, mounting ___________________ 4 clearances ___________________ 5 Installation ___________________ 6 Technical data ___________________ 7 Safety, approvals, EMC ___________________ 8 Ambient conditions LOGO!Power 5 V/3 A 6EP3310-6SB00-0AY0 LOGO!Power 5 V/6.3 A 6EP3311-6SB00-0AY0 LOGO!Power 12 V/0.9 A 6EP3320-6SB00-0AY0 LOGO!Power 12 V/1.9 A 6EP3321-6SB00-0AY0 LOGO!Power 12 V/4.5 A 6EP3322-6SB00-0AY0 LOGO!Power 15 V/1.9 A 6EP3321-6SB10-0AY0 LOGO!Power 15 V/4 A 6EP3322-6SB10-0AY0 LOGO!Power 24 V/0.6 A 6EP3330-6SB00-0AY0 LOGO!Power 24 V/1.3 A 6EP3331-6SB00-0AY0 LOGO!Power 24 V/2.5 A 6EP3332-6SB00-0AY0 LOGO!Power 24 V/4 A 6EP3333-6SB00-0AY0 06.2017 A5E40912965-1-76 ___________________ 9 Applications ___________________ 10 Environment ___________________ 11 Service & Support Legal information Warning notice system This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger. DANGER indicates that death or severe personal injury will result if proper precautions are not taken. WARNING indicates that death or severe personal injury may result if proper precautions are not taken. CAUTION indicates that minor personal injury can result if proper precautions are not taken. NOTICE indicates that property damage can result if proper precautions are not taken. If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage. Qualified Personnel The product/system described in this documentation may be operated only by personnel qualified for the specific task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified personnel are those who, based on their training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems. Proper use of Siemens products Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems. The permissible ambient conditions must be complied with. The information in the relevant documentation must be observed. Trademarks All names identified by (R) are registered trademarks of Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner. Disclaimer of Liability We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions. Siemens AG Division Process Industries and Drives Postfach 48 48 90026 NURNBERG GERMANY A5E40912965-1-76 06/2017 Subject to change Copyright (c) Siemens AG 2017. All rights reserved Overview Figure 1 View of devices LOGO!Power are powerful power supplies that can be extremely flexibly used in a host of applications - in installation distribution boards for example - as a result of their flat, stepped profile. The 12 V and 24 V versions are ideal as power supplies for the LOGO! logic modules. The key benefits of the product include: Reduced widths, and therefore the narrowest device available in the market in its power class Power loss in no-load operation (standby) <0.3 W Briefly (i.e. up to 1sec) up to AC 300 V at the input Operation with a DC voltage from 110 - 300 V DC LOGO!Power Manual, 06.2017, A5E40912965-1-76 3 Overview Improved efficiency across the entire load range Power reserve of 150 % (typ. 200 ms) for capacitive loads when the power supply runs up Measuring point for actual output current Extended operating temperature range from -25 C up to +70 C (derating from 55 C) Standard rail and wall mounting Ordering data The following device options are available: LOGO!Power stabilized power supply Type Order number Input 85 to 264 V AC 110 to 300 V DC 6EP3310-6SB00-0AY0 Output 5 V DC/3 A Input 85 to 264 V AC 110 to 300 V DC 6EP3311-6SB00-0AY0 Output 5 V DC/6.3 A Input 85 to 264 V AC 110 to 300 V DC 6EP3320-6SB00-0AY0 Output 12 V DC/0.9 A Input 85 to 264 V AC 110 to 300 V DC 6EP3321-6SB00-0AY0 Output 12 V DC/1.9 A Input 85 to 264 V AC 110 to 300 V DC 6EP3322-6SB00-0AY0 Output 12 V DC/4.5 A Input 85 to 264 V AC 110 to 300 V DC 6EP3321-6SB10-0AY0 Output 15 V DC/1.9 A Input 85 to 264 V AC 110 to 300 V DC 6EP3322-6SB10-0AY0 Output 15 V DC/4 A Input 85 to 264 V AC 110 to 300 V DC 6EP3330-6SB00-0AY0 Output, 24 V DC/0.6 A Input 85 to 264 V AC 110 to 300 V DC 6EP3331-6SB00-0AY0 Output 24 V DC/1.3 A Input 85 to 264 V AC 110 to 300 V DC 6EP3332-6SB00-0AY0 Output 24 V DC/2.5 A Input 85 to 264 V AC 110 to 300 V DC 6EP3333-6SB00-0AY0 Output 24 VDC/4 A LOGO!Power 4 Manual, 06.2017, A5E40912965-1-76 Table of contents Overview................................................................................................................................................. 3 1 Safety instructions ................................................................................................................................... 7 2 Description, device design, dimension drawing........................................................................................ 9 2.1 Device description..................................................................................................................... 9 2.2 Connections and terminal designation....................................................................................11 2.3 Potentiometer ..........................................................................................................................13 2.4 Status displays and signaling .................................................................................................14 2.5 Block diagram .........................................................................................................................16 2.6 Dimensions and weight ...........................................................................................................17 3 Mounting/removal ................................................................................................................................. 21 4 Mounting position, mounting clearances ................................................................................................ 23 5 6 4.1 Standard mounting position ....................................................................................................23 4.2 4.2.1 4.2.2 4.2.3 4.2.4 4.2.5 4.2.6 4.2.7 4.2.8 4.2.9 4.2.10 4.2.11 Other mounting positions ........................................................................................................28 6EP3310-6SB00-0AY0 (5V 3A) ..............................................................................................28 6EP3311-6SB00-0AY0 (5V 6.3A) ...........................................................................................30 6EP3320-6SB00-0AY0 (12V 0.9A) .........................................................................................32 6EP3321-6SB00-0AY0 (12V 1.9A) .........................................................................................34 6EP3322-6SB00-0AY0 (12V 4.5A) .........................................................................................36 6EP3321-6SB10-0AY0 (15V 1.9A) .........................................................................................38 6EP3322-6SB10-0AY0 (15V 4A) ............................................................................................40 6EP3330-6SB00-0AY0 (24V 0.6A) .........................................................................................42 6EP3331-6SB00-0AY0 (24V 1.3A) .........................................................................................44 6EP3332-6SB10-0AY0 (24V 2.5A) .........................................................................................46 6EP3333-6SB00-0AY0 (24V 4A) ............................................................................................48 Installation ............................................................................................................................................ 51 5.1 Line-side connection ...............................................................................................................51 5.2 Output-side connection ...........................................................................................................53 Technical data ...................................................................................................................................... 55 6.1 Input ........................................................................................................................................55 6.2 Output .....................................................................................................................................58 6.3 Efficiency and power loss .......................................................................................................63 6.4 Closed-loop control .................................................................................................................69 6.5 Protection and monitoring .......................................................................................................70 6.6 MTBF ......................................................................................................................................71 6.7 Mechanical system .................................................................................................................72 LOGO!Power Manual, 06.2017, A5E40912965-1-76 5 Table of contents 6.8 7 Dimension drawing ................................................................................................................ 73 Safety, approvals, EMC ........................................................................................................................ 75 7.1 Safety ..................................................................................................................................... 75 7.2 Test voltage............................................................................................................................ 76 7.3 Certifications .......................................................................................................................... 77 7.4 EMC ....................................................................................................................................... 78 8 Ambient conditions................................................................................................................................ 79 9 Applications .......................................................................................................................................... 81 9.1 Parallel connection to increase power rating ......................................................................... 81 9.2 Parallel connection for redundancy ....................................................................................... 83 9.3 Series connection for increased voltage ................................................................................ 84 9.4 Protection against short-time voltage dips ............................................................................. 85 10 Environment ......................................................................................................................................... 87 11 Service & Support ................................................................................................................................. 89 LOGO!Power 6 Manual, 06.2017, A5E40912965-1-76 Safety instructions 1 WARNING Correct handling of the devices When operating electrical devices, it is inevitable that certain components will carry dangerous voltages. Therefore, failure to handle the units properly can result in death or serious physical injury as well as extensive property damage. Only appropriately qualified personnel may work on or in the vicinity of this equipment. Perfect, safe, and reliable operation of this equipment is dependent on proper transportation, storage, installation and mounting. Before installation or maintenance work can begin, the system's main switch must be switched off and measures taken to prevent it being switched on again. If this instruction is not observed, touching live parts can result in death or serious injury. LOGO!Power Manual, 06.2017, A5E40912965-1-76 7 Safety instructions LOGO!Power 8 Manual, 06.2017, A5E40912965-1-76 Description, device design, dimension drawing 2.1 2 Device description LOGO!Power are primary switched-mode power supplies for connection to a 1-phase AC system or to DC systems. An electronically regulated DC voltage that can be set via a potentiometer is available at the output of the device. The output of the device is isolated, no-load proof and short-circuit proof. The LED display indicates the operating status. AC input (optionally, also DC input) DC output Potentiometer Pilot lamp Measuring point (for output current) DIN rail slider Withdrawable mounting lugs Convection Clearance above/below Figure 2-1 Design 36 mm, 54 mm and 72 mm devices (example 6EP3332-6SB00-0AY0) LOGO!Power Manual, 06.2017, A5E40912965-1-76 9 Description, device design, dimension drawing 2.1 Device description AC input (optionally, also DC input) DC output Pilot lamp DIN rail slider Withdrawable mounting lugs Convection Clearance above/below Figure 2-2 Design 18 mm devices (example 6EP3320-6SB00-0AY0) LOGO!Power 10 Manual, 06.2017, A5E40912965-1-76 Description, device design, dimension drawing 2.2 Connections and terminal designation 2.2 Connections and terminal designation Note UL requirement: Use suitable copper cables that are designed for operating temperatures of at least 65 C/75 C. The line input terminals can be used to establish the connection to supply voltage. The output terminals are used to connect to the loads to be supplied (see also Section Installation (Page 51)). For 6EP3310-6SB00-0AY0, 6EP3311-6SB00-0AY0, 6EP3321-6SB00-0AY0, 6EP3322-6SB00-0AY0, 6EP3321-6SB10-0AY0, 6EP3322-6SB10-0AY0, 6EP3331-6SB00-0AY0, 6EP3332-6SB00-0AY0 and 6EP3333-6SB00-0AY0 Connections and terminal designations Line input L1, N One screw terminal each Output + Two screw terminals Output - Two screw terminals *1) Do not subject the end stop to higher loads Figure 2-3 Terminal data LOGO!Power Manual, 06.2017, A5E40912965-1-76 11 Description, device design, dimension drawing 2.2 Connections and terminal designation For 6EP3320-6SB00-0AY0 and 6EP3330-6SB00-0AY0 Connections and terminal designations Line input L1, N One screw terminal each Output + One screw terminal Output - One screw terminal Figure 2-4 Terminal data LOGO!Power 12 Manual, 06.2017, A5E40912965-1-76 Description, device design, dimension drawing 2.3 Potentiometer 2.3 Potentiometer The potentiometer on the front of the device is used to set the output voltage. The output voltage is set to the rated value at the factory and can be set within certain limits; for example, to compensate voltage drops across long supply lines to the connected load. Figure 2-5 Potentiometer (example 6EP3332-6SB00-0AY0) Type Factory setting Setting range 6EP3310-6SB00-0AY0 (5 V/3 A) 5V 4.6 - 5.4 V 12 V 10.5 - 16.1 V 15 V 10.5 - 16.1 V 24 V 22.2 - 26.4 V 12 V 24 V no setting possible 6EP3311-6SB00-0AY0 (5 V/6.3 A) 6EP3321-6SB00-0AY0 (12 V/1.9 A) 6EP3322-6SB00-0AY0 (12 V/4.5 A) 6EP3321-6SB10-0AY0 (15 V/1.9 A) 6EP3322-6SB10-0AY0 (15 V/4 A) 6EP3331-6SB00-0AY0 (24 V/1.3 A) 6EP3332-6SB00-0AY0 (24 V/2.5 A) 6EP3333-6SB00-0AY0 (24 V/4 A) 6EP3320-6SB00-0AY0 (12 V/0.9 A) 6EP3330-6SB00-0AY0 (24 V/0.6 A) NOTICE Thermal overload possible When adjusting the output voltage to > 24 V/> 15 V/> 12 V or > 5 V, the output current must be derated. It is not permissible that the maximum active power that can be output is exceeded. Note Actuation of the potentiometer is allowed only by means of an insulated screwdriver. For notes on actuating the potentiometer (screwdriver, torque), see Figure 2-3 Terminal data (Page 11). LOGO!Power Manual, 06.2017, A5E40912965-1-76 13 Description, device design, dimension drawing 2.4 Status displays and signaling 2.4 Status displays and signaling 6EP3310-6SB00-0AY0 (5 V/3 A) 6EP3322-6SB10-0AY0 (15 V/4 A) 6EP3311-6SB00-0AY0 (5 V/6.3 A) 6EP3330-6SB00-0AY0 (24 V/0.6 A) 6EP3320-6SB00-0AY0 (12 V/0.9 A) 6EP3331-6SB00-0AY0 (24 V/1.3 A) 6EP3321-6SB00-0AY0 (12 V/1.9 A) 6EP3332-6SB00-0AY0 (24 V/2.5 A) 6EP3322-6SB00-0AY0 (12 V/4.5 A) 6EP3333-6SB00-0AY0 (24 V/4 A) 6EP3321-6SB10-0AY0 (15 V/1.9 A) Status display Green LED for output voltage OK Figure 2-6 Signaling Status displays and signaling 6EP3310-6SB00-0AY0 (5 V/3 A) 6EP3322-6SB10-0AY0 (15 V/4 A) 6EP3311-6SB00-0AY0 (5 V/6.3 A) 6EP3330-6SB00-0AY0 (24 V/0.6 A) 6EP3320-6SB00-0AY0 (12 V/0.9 A) 6EP3331-6SB00-0AY0 (24 V/1.3 A) 6EP3321-6SB00-0AY0 (12 V/1.9 A) 6EP3332-6SB00-0AY0 (24 V/2.5 A) 6EP3322-6SB00-0AY0 (12 V/4.5 A) 6EP3333-6SB00-0AY0 (24 V/4 A) 6EP3321-6SB10-0AY0 (15 V/1.9 A) LED lights up green Normal operation, output voltage present LED off Output voltage not present LOGO!Power 14 Manual, 06.2017, A5E40912965-1-76 Description, device design, dimension drawing 2.4 Status displays and signaling Measuring point for output current Figure 2-7 Measuring point (for output current) and setting Uout The measuring point (for max. 2.5 mm test probe) at the front side of the device is used to measure the output current. The voltage between the measuring point and the "-" terminal is proportional to the output current: refer to the table below Device Iout rated Measuring point 6EP3310-6SB00-0AY0 (5 V/3 A) 3A ~ 50 mV 3 A 6EP3311-6SB00-0AY0 (5 V/6.3 A) 6.3 A ~ 50 mV 6.3 A 6EP3320-6SB00-0AY0 (12 V/0.9 A) 0.9 A - 6EP3321-6SB00-0AY0 (12 V/1.9 A) 1.9 A ~ 50 mV 1.9 A 6EP3322-6SB00-0AY0 (12 V/4.5 A) 4.5 A ~ 50 mV 4.5 A 6EP3321-6SB10-0AY0 (15 V/1.9 A) 1.9 A ~ 50 mV 1.9 A 6EP3322-6SB10-0AY0 (15 V/4 A) 4A ~ 45 mV 4 A 6EP3330-6SB00-0AY0 (24 V/0.6 A) 0.6 A - 6EP3331-6SB00-0AY0 (24 V/1.3 A) 1.3 A ~ 50 mV 1.3 A 6EP3332-6SB00-0AY0 (24 V/2.5 A) 2.5 A ~ 50 mV 2.5 A 6EP3333-6SB00-0AY0 (24 V/4 A) 4A ~ 50 mV 4 A LOGO!Power Manual, 06.2017, A5E40912965-1-76 15 Description, device design, dimension drawing 2.5 Block diagram 2.5 Block diagram Figure 2-8 Block diagram for 36 mm, 54 mm and 72 mm devices Figure 2-9 Block diagram for 18 mm devices LOGO!Power 16 Manual, 06.2017, A5E40912965-1-76 Description, device design, dimension drawing 2.6 Dimensions and weight 2.6 Dimensions and weight Figure 2-10 Dimension drawing for 6EP3320-6SB00-0AY0 and 6EP3330-6SB00-0AY0 LOGO!Power Manual, 06.2017, A5E40912965-1-76 17 Description, device design, dimension drawing 2.6 Dimensions and weight Figure 2-11 Dimension drawing for 6EP3310-6SB00-0AY0, 6EP3321-6SB00-0AY0, 6EP33216SB10-0AY0 and EP3331-6SB00-0AY0 LOGO!Power 18 Manual, 06.2017, A5E40912965-1-76 Description, device design, dimension drawing 2.6 Dimensions and weight Figure 2-12 Dimension drawing for 6EP3311-6SB00-0AY0, 6EP3322-6SB00-0AY0, 6EP33226SB10-0AY0 and 6EP3332-6SB00-0AY0 Figure 2-13 Dimension drawing for 6EP3333-6SB00-0AY0 LOGO!Power Manual, 06.2017, A5E40912965-1-76 19 Description, device design, dimension drawing 2.6 Dimensions and weight 6EP3320-6SB00-0AY0 6EP3310-6SB00-0AY0 6EP3311-6SB00-0AY0 6EP3333-6SB00-0AY0 (12 V/0.9 A) (5 V/3 A) (5 V/6.3 A) (24 V/4 A) 6EP3330-6SB00-0AY0 6EP3321-6SB00-0AY0 6EP3322-6SB00-0AY0 (24 V/0.6 A) (12 V/1.9 A) (12 V/4.5 A) 6EP3321-6SB10-0AY0 6EP3322-6SB10-0AY0 (15 V/1.9 A) (15 V/4 A) 6EP3331-6SB00-0AY0 6EP3332-6SB00-0AY0 (24 V/1.3 A) (24 V/2.5 A) Dimensions (W x H x D) in mm 18 x 90 x 53 36 x 90 x 53 54 x 90 x 53 72 x 90 x 53 Weight 0.07 kg 0.12 kg 0.2 kg 0.29 kg LOGO!Power 20 Manual, 06.2017, A5E40912965-1-76 Mounting/removal 3 WARNING Installing the device in a housing or a control cabinet LOGO!Power power supplies are built-in devices. They must be installed in a casing or control cabinet to which only qualified personnel have access. The devices can be mounted in a control cabinet on standard mounting rails according to (see Mechanical system (Page 72)). All devices are suitable for mounting directly on walls. Mounting To mount the device on a standard mounting, position it with the mounting rail guide at the upper edge of the standard mounting rail and press down to lock it into place. If this is too difficult, press slider at the same time, as described for "Disassembly". Disassembly To remove, pull up the slider using a screwdriver and disengage the device at the bottom edge of the DIN rail. Then you can remove the device from the upper edge of the DIN rail. Figure 3-1 Mounting/removal (example 6EP3310-6SB00-0AY0) LOGO!Power Manual, 06.2017, A5E40912965-1-76 21 Mounting/removal Figure 3-2 Wall mounting To mount on a flat surface, place the device with the sliders extended over the holes as shown in Fig. 3-2, and fix in place using suitable screws. WARNING Use in hazardous zones If the device is to be used in a hazardous zone (Ex II 3G Ex nA IIC T3) it must be installed in a distributor box with degree of protection IP54 or higher. LOGO!Power 22 Manual, 06.2017, A5E40912965-1-76 Mounting position, mounting clearances 4.1 4 Standard mounting position The device is mounted on standard mounting rails according to EN 60715 35x7,5/15. To ensure correct cooling, the device should be vertically mounted so that the terminal strip or, as a result of the different designs, the output terminal of the 18 mm wide devices is at the top. A clearance of at least 20 mm should be maintained above and below the device. No space is required at the side. Figure 4-1 Output current for the standard mounting position 6EP3310-6SB00-0AY0 Figure 4-2 Output current for the standard mounting position 6EP3321-6SB00-0AY0 LOGO!Power Manual, 06.2017, A5E40912965-1-76 23 Mounting position, mounting clearances 4.1 Standard mounting position Figure 4-3 Output current for the standard mounting position 6EP3321-6SB10-0AY0 Figure 4-4 Output current for the standard mounting position 6EP3331-6SB00-0AY0 Figure 4-5 Output current for the standard mounting position 6EP3311-6SB00-0AY0 LOGO!Power 24 Manual, 06.2017, A5E40912965-1-76 Mounting position, mounting clearances 4.1 Standard mounting position Figure 4-6 Output current for the standard mounting position 6EP3320-6SB00-0AY0 Figure 4-7 Output current for the standard mounting position 6EP3322-6SB00-0AY0 Figure 4-8 Output current for the standard mounting position 6EP3322-6SB10-0AY0 LOGO!Power Manual, 06.2017, A5E40912965-1-76 25 Mounting position, mounting clearances 4.1 Standard mounting position Figure 4-9 Output current for the standard mounting position 6EP3330-6SB00-0AY0 Figure 4-10 Output current for the standard mounting position 6EP3332-6SB00-0AY0 Figure 4-11 Output current for the standard mounting position 6EP3333-6SB00-0AY0 LOGO!Power 26 Manual, 06.2017, A5E40912965-1-76 Mounting position, mounting clearances 4.1 Standard mounting position Figure 4-12 Mounting height derating For details, see Section Ambient conditions (Page 79) LOGO!Power Manual, 06.2017, A5E40912965-1-76 27 Mounting position, mounting clearances 4.2 Other mounting positions 4.2 Other mounting positions For mounting positions that deviate from the standard mounting position, derating factors (reduction of the output power or the permissible ambient temperature) must be observed in accordance with the following diagrams. Note In the case of mounting positions that deviate from the standard mounting position, reduced mechanical resistance of the devices against vibration and shock must be expected. Particularly when installing on a vertically fastened standard mounting rail, additional measures may be required, e.g. to prevent the device from slipping on the standard mounting rail. 4.2.1 6EP3310-6SB00-0AY0 (5V 3A) Figure 4-13 Mounting position 1 Figure 4-14 Mounting position 2 LOGO!Power 28 Manual, 06.2017, A5E40912965-1-76 Mounting position, mounting clearances 4.2 Other mounting positions Figure 4-15 Mounting position 3 Figure 4-16 Mounting position 4 Figure 4-17 Mounting position 5 LOGO!Power Manual, 06.2017, A5E40912965-1-76 29 Mounting position, mounting clearances 4.2 Other mounting positions 4.2.2 6EP3311-6SB00-0AY0 (5V 6.3A) Figure 4-18 Mounting position 1 Figure 4-19 Mounting position 2 Figure 4-20 Mounting position 3 LOGO!Power 30 Manual, 06.2017, A5E40912965-1-76 Mounting position, mounting clearances 4.2 Other mounting positions Figure 4-21 Mounting position 4 Figure 4-22 Mounting position 5 LOGO!Power Manual, 06.2017, A5E40912965-1-76 31 Mounting position, mounting clearances 4.2 Other mounting positions 4.2.3 6EP3320-6SB00-0AY0 (12V 0.9A) Figure 4-23 Mounting position 1 Figure 4-24 Mounting position 2 Figure 4-25 Mounting position 3 LOGO!Power 32 Manual, 06.2017, A5E40912965-1-76 Mounting position, mounting clearances 4.2 Other mounting positions Figure 4-26 Mounting position 4 Figure 4-27 Mounting position 5 LOGO!Power Manual, 06.2017, A5E40912965-1-76 33 Mounting position, mounting clearances 4.2 Other mounting positions 4.2.4 6EP3321-6SB00-0AY0 (12V 1.9A) Figure 4-28 Mounting position 1 Figure 4-29 Mounting position 2 Figure 4-30 Mounting position 3 LOGO!Power 34 Manual, 06.2017, A5E40912965-1-76 Mounting position, mounting clearances 4.2 Other mounting positions Figure 4-31 Mounting position 4 Figure 4-32 Mounting position 5 LOGO!Power Manual, 06.2017, A5E40912965-1-76 35 Mounting position, mounting clearances 4.2 Other mounting positions 4.2.5 6EP3322-6SB00-0AY0 (12V 4.5A) Figure 4-33 Mounting position 1 Figure 4-34 Mounting position 2 Figure 4-35 Mounting position 3 LOGO!Power 36 Manual, 06.2017, A5E40912965-1-76 Mounting position, mounting clearances 4.2 Other mounting positions Figure 4-36 Mounting position 4 Figure 4-37 Mounting position 5 LOGO!Power Manual, 06.2017, A5E40912965-1-76 37 Mounting position, mounting clearances 4.2 Other mounting positions 4.2.6 6EP3321-6SB10-0AY0 (15V 1.9A) Figure 4-38 Mounting position 1 Figure 4-39 Mounting position 2 Figure 4-40 Mounting position 3 LOGO!Power 38 Manual, 06.2017, A5E40912965-1-76 Mounting position, mounting clearances 4.2 Other mounting positions Figure 4-41 Mounting position 4 Figure 4-42 Mounting position 5 LOGO!Power Manual, 06.2017, A5E40912965-1-76 39 Mounting position, mounting clearances 4.2 Other mounting positions 4.2.7 6EP3322-6SB10-0AY0 (15V 4A) Figure 4-43 Mounting position 1 Figure 4-44 Mounting position 2 Figure 4-45 Mounting position 3 LOGO!Power 40 Manual, 06.2017, A5E40912965-1-76 Mounting position, mounting clearances 4.2 Other mounting positions Figure 4-46 Mounting position 4 Figure 4-47 Mounting position 5 LOGO!Power Manual, 06.2017, A5E40912965-1-76 41 Mounting position, mounting clearances 4.2 Other mounting positions 4.2.8 6EP3330-6SB00-0AY0 (24V 0.6A) Figure 4-48 Mounting position 1 Figure 4-49 Mounting position 2 Figure 4-50 Mounting position 3 LOGO!Power 42 Manual, 06.2017, A5E40912965-1-76 Mounting position, mounting clearances 4.2 Other mounting positions Figure 4-51 Mounting position 4 Figure 4-52 Mounting position 5 LOGO!Power Manual, 06.2017, A5E40912965-1-76 43 Mounting position, mounting clearances 4.2 Other mounting positions 4.2.9 6EP3331-6SB00-0AY0 (24V 1.3A) Figure 4-53 Mounting position 1 Figure 4-54 Mounting position 2 Figure 4-55 Mounting position 3 LOGO!Power 44 Manual, 06.2017, A5E40912965-1-76 Mounting position, mounting clearances 4.2 Other mounting positions Figure 4-56 Mounting position 4 Figure 4-57 Mounting position 5 LOGO!Power Manual, 06.2017, A5E40912965-1-76 45 Mounting position, mounting clearances 4.2 Other mounting positions 4.2.10 6EP3332-6SB10-0AY0 (24V 2.5A) Figure 4-58 Mounting position 1 Figure 4-59 Mounting position 2 Figure 4-60 Mounting position 3 LOGO!Power 46 Manual, 06.2017, A5E40912965-1-76 Mounting position, mounting clearances 4.2 Other mounting positions Figure 4-61 Mounting position 4 Figure 4-62 Mounting position 5 LOGO!Power Manual, 06.2017, A5E40912965-1-76 47 Mounting position, mounting clearances 4.2 Other mounting positions 4.2.11 6EP3333-6SB00-0AY0 (24V 4A) Figure 4-63 Mounting position 1 Figure 4-64 Mounting position 2 Figure 4-65 Mounting position 3 LOGO!Power 48 Manual, 06.2017, A5E40912965-1-76 Mounting position, mounting clearances 4.2 Other mounting positions Figure 4-66 Mounting position 4 Figure 4-67 Mounting position 5 LOGO!Power Manual, 06.2017, A5E40912965-1-76 49 Mounting position, mounting clearances 4.2 Other mounting positions LOGO!Power 50 Manual, 06.2017, A5E40912965-1-76 5 Installation WARNING Hazard due to electric shock Before installation or maintenance work can begin, the system's main switch must be switched off and measures taken to prevent it being switched on again. If this instruction is not observed, touching live parts can result in death or serious injury. 5.1 Line-side connection LOGO!Power power supplies are devices that are connected to a line supply with protection class II (without protective conductor, which means without PE). LOGO!Power are designed for connection to 1-phase AC line supplies (TN or TT line supply according to IEC 60364-1) with rated voltage 1 AC 100 - 240 V, 50/60 Hz or to a DC power supply with 110 - 300 V DC. Figure 5-1 Line connection (example) The line supply is connected using terminal L1 and N (see Figure Line connection (example) (Page 51)), and must be implemented according to IEC 60364 and EN 50178. A protective device (miniature circuit-breaker or circuit-breaker) and a disconnection unit for the power supply must be provided. A ground-fault circuit interrupter must not be used as the only protective measure against indirect contact; this applies to the entire supply system that is protected by the residual current operated circuit-breaker. Note For operation on a direct voltage network (DC), the plus pole (+) must be connected to L1 and the minus pole (-) to N. LOGO!Power Manual, 06.2017, A5E40912965-1-76 51 Installation 5.1 Line-side connection Protection LOGO!Power Recommended line-side protection 6EP3310-6SB00-0AY0 (5 V/3 A) Recommended miniature circuit breaker, characteristic B (C) 6 A (2 A) 6EP3311-6SB00-0AY0 (5 V/6.3 A) Recommended miniature circuit breaker, characteristic B (C) 10 A (6 A) 6EP3320-6SB00-0AY0 (12 V/0.9 A) Recommended miniature circuit breaker, characteristic B (C) 6 A (2 A) 6EP3321-6SB00-0AY0 (12 V/1.9 A) Recommended miniature circuit breaker, characteristic B (C) 6 A (2 A) 6EP3322-6SB00-0AY0 (12 V/4.5 A) Recommended miniature circuit breaker, characteristic B (C) 10 A (6 A) 6EP3321-6SB10-0AY0 (15 V/1.9 A) Recommended miniature circuit breaker, characteristic B (C) 6 A (2 A) 6EP3322-6SB10-0AY0 (15 V/4 A) Recommended miniature circuit breaker, characteristic B (C) 10 A (6 A) 6EP3330-6SB00-0AY0 (24 V/0.6 A) Recommended miniature circuit breaker, characteristic B (C) 6 A (2 A) 6EP3331-6SB00-0AY0 (24 V/1.3 A) Recommended miniature circuit breaker, characteristic B (C) 6 A (2 A) 6EP3332-6SB00-0AY0 (24 V/2.5 A) Recommended miniature circuit breaker, characteristic B (C) 10 A (6 A) 6EP3333-6SB00-0AY0 (24 V/4 A) Recommended miniature circuit breaker, characteristic B (C) 10 A (6 A) NOTICE Country-specific regulations must be observed when installing. LOGO!Power 52 Manual, 06.2017, A5E40912965-1-76 Installation 5.2 Output-side connection 5.2 Output-side connection LOGO!Power power supplies provide an isolated (= non-grounded, floating) SELV (Safety Extra Low Voltage) output voltage. The output of the power supplies is no-load, overload and short-circuit proof. If an overload occurs, the electronic current limiting function limits the output current to a maximum value (see Section Technical data (Page 55)). Figure 5-2 Output (examples) The output voltage is connected via the + and - terminals at the output of the power supply (see Figure Output (examples) (Page 53)). Make sure that the output cables are dimensioned correctly for the maximum output current rms value and fused accordingly. Note When using LOGO!Power in conjunction with devices of the protection class I (with protective conductor), a connection must be established between "-" and "PE" with at least 1.5 mm. LOGO!Power Manual, 06.2017, A5E40912965-1-76 53 Installation 5.2 Output-side connection LOGO!Power 54 Manual, 06.2017, A5E40912965-1-76 6 Technical data Note Technical data apply for a rated input voltage, rated load and 25 C ambient temperature if nothing else is specified. 6.1 Input 6EP33106SB00-0AY0 6EP33116SB00-0AY0 6EP33206SB00-0AY0 6EP33216SB00-0AY0 6EP33226SB00-0AY0 6EP33216SB10-0AY0 (5 V/3 A) (5 V/6.3 A) (12 V/0.9 A) (12 V/1.9 A) (12 V/4.5 A) (15 V/1.9 A) Input 1-phase AC or DC 1-phase AC or DC 1-phase AC or DC 1-phase AC or DC 1-phase AC or DC 1-phase AC or DC Rated voltage Uin rated for AC 100 - 240 V 100 - 240 V 100 - 240 V 100 - 240 V 100 - 240 V 100 - 240 V Voltage range for AC 85 - 264 V 85 - 264 V 85 - 264 V 85 - 264 V 85 - 264 V 85 - 264 V Input voltage for DC 110 - 300 V 110 - 300 V 110 - 300 V 110 - 300 V 110 - 300 V 110 - 300 V Wide-range input Yes Yes Yes Yes Yes Yes Overvoltage resistance 300 V AC for 1 s 300 V AC for 1 s 300 V AC for 1 s 300 V AC for 1 s 300 V AC for 1 s 300 V AC for 1 s Power failure buffering at Iout rated and Uin = 187 V: min. 40 ms 40 ms 40 ms 40 ms 40 ms 40 ms Rated line frequency 50/60 Hz 50/60 Hz 50/60 Hz 50/60 Hz 50/60 Hz 50/60 Hz Line frequency range 47 - 63 Hz 47 - 63 Hz 47 - 63 Hz 47 - 63 Hz 47 - 63 Hz 47 - 63 Hz Input current at Uin rated 120 V 0.33 A 0.68 A 0.20 A 0.45 A 1.02 A 0.53 A Input current at Uin rated 230 V 0.23 A 0.42 A 0.14 A 0.30 A 0.64 A 0.34 A Inrush current limiting (25 C), max. 26 A 51 A 20 A 25 A 50 A 25 A It, max. 0.8 As 3 As 0.3 As 0.8 As 3 As 0.8 As LOGO!Power Manual, 06.2017, A5E40912965-1-76 55 Technical data 6.1 Input 6EP33106SB00-0AY0 6EP33116SB00-0AY0 6EP33206SB00-0AY0 6EP33216SB00-0AY0 6EP33226SB00-0AY0 6EP33216SB10-0AY0 (5 V/3 A) (5 V/6.3 A) (12 V/0.9 A) (12 V/1.9 A) (12 V/4.5 A) (15 V/1.9 A) Built-in line-side Internal fuse Internal Internal Internal Internal Internal Protection in Recommended the line feeder miniature circable (IEC 898) cuit-breaker: Characteristic B from 6 A or characteristic C from 2 A Recommended miniature circuit-breaker: Characteristic B from 10 A or characteristic C from 6 A Recommended miniature circuit-breaker: Characteristic B from 6 A or characteristic C from 2 A Recommended miniature circuit-breaker: Characteristic B from 6 A or characteristic C from 2 A Recommended miniature circuit-breaker: Characteristic B from 10 A or characteristic C from 6 A Recommended miniature circuit-breaker: Characteristic B from 6 A or characteristic C from 2 A 6EP3322-6SB100AY0 6EP3330-6SB000AY0 6EP3331-6SB000AY0 6EP3332-6SB000AY0 6EP3333-6SB000AY0 (15 V/4 A) (24 V/0.6 A) (24 V/1.3 A) (24 V/2.5 A) (24 V/4 A) Input 1-phase AC or DC 1-phase AC or DC 1-phase AC or DC 1-phase AC or DC 1-phase AC or DC Rated voltage Uin rated for AC 100 - 240 V 100 - 240 V 100 - 240 V 100 - 240 V 100 - 240 V Voltage range for AC 85 - 264 V 85 - 264 V 85 - 264 V 85 - 264 V 85 - 264 V Input voltage for DC 110 - 300 V 110 - 300 V 110 - 300 V 110 - 300 V 110 - 300 V Wide-range input Yes Yes Yes Yes Yes Overvoltage resistance 300 V AC for 1 s 300 V AC for 1 s 300 V AC for 1 s 300 V AC for 1 s 300 V AC for 1 s Power failure 40 ms buffering at Iout rated and Uin = 187 V: min. 40 ms 40 ms 40 ms 40 ms Rated line frequency 50/60 Hz 50/60 Hz 50/60 Hz 50/60 Hz 50/60 Hz Line frequency range 47 - 63 Hz 47 - 63 Hz 47 - 63 Hz 47 - 63 Hz 47 - 63 Hz Input current at 1.10 A 0.25 A 0.56 A 1.08 A 1.70 A 0.70 A 0.16 A 0.37 A 0.70 A 1.00 A Inrush current limiting (25 C), max. 50 A 20 A 25 A 50 A 30 A It, max. 3 As 0.5 As 0.8 As 3.3 As 2.5 As Uin rated 120 V Input current at Uin rated 230 V LOGO!Power 56 Manual, 06.2017, A5E40912965-1-76 Technical data 6.1 Input 6EP3322-6SB100AY0 6EP3330-6SB000AY0 6EP3331-6SB000AY0 6EP3332-6SB000AY0 6EP3333-6SB000AY0 (15 V/4 A) (24 V/0.6 A) (24 V/1.3 A) (24 V/2.5 A) (24 V/4 A) Built-in line-side fuse Internal Internal Internal Internal Internal Protection in the line feeder cable (IEC 898) Recommended miniature circuitbreaker: Characteristic B from 10 A or characteristic C from 6 A Recommended miniature circuitbreaker: Characteristic B from 6 A or characteristic C from 2 A Recommended miniature circuitbreaker: Characteristic B from 6 A or characteristic C from 2 A Recommended miniature circuitbreaker: Characteristic B from 10 A or characteristic C from 6 A Recommended miniature circuitbreaker: Characteristic B from 10 A or characteristic C from 6 A Figure 6-1 Mains buffering LOGO!Power Manual, 06.2017, A5E40912965-1-76 57 Technical data 6.2 Output 6.2 Output 6EP33106SB00-0AY0 6EP33116SB00-0AY0 6EP33206SB00-0AY0 6EP33216SB00-0AY0 6EP33226SB00-0AY0 6EP33216SB10-0AY0 (5 V/3 A) (5 V/6.3 A) (12 V/0.9 A) (12 V/1.9 A) (12 V/4.5 A) (15 V/1.9 A) Output Regulated, isolated DC voltage Rated output voltage Uout rated DC: 5V 5V 12 V 12 V 12 V 15 V Total tolerance, 3 % static 3% 3% 3% 3% 3% Static line regu- 0.1 % lation, approx. 0.1 % 0.1 % 0.1 % 0.1 % 0.1 % Static load regulation, approx. 0.1 % 0.1 % 0.1 % 0.1 % 0.1 % 0.1 % Residual ripple peak-peak, max. 100 mV 100 mV 200 mV 200 mV 200 mV 200 mV Residual ripple peak-peak, typ. 30 mV 30 mV 30 mV 30 mV 30 mV 30 mV Spikes peakpeak, max. (bandwidth, approx. 20 MHz) 100 mV 300 mV 300 mV 300 mV 300 mV 300 mV Spikes peakpeak, typ. (bandwidth, approx. 20 MHz) 50 mV 50 mV 50 mV 50 mV 50 mV 50 mV Setting range 4.6 - 5.4 V 4.6 - 5.4 V - 10.5 - 16.1 V 10.5 - 16.1 V 10.5 - 16.1 V Product function/output voltage can be adjusted Yes Yes No Yes Yes Yes Output voltage setting Using a potentiometer Using a potentiometer - Using a potentiometer Using a potentiometer Using a potentiometer Status display Green LED for output voltage OK Response when switching on/off No overshoot of Uout (soft start) Starting delay, max. 0.5 s 0.5 s 0.5 s 0.5 s 0.5 s 0.5 s Voltage rise, typ. 100 ms 100 ms 100 ms 100 ms 100 ms 100 ms Rated current Iout rated 3A 6.3 A 0.9 A 1.9 A 4.5 A 1.9 A LOGO!Power 58 Manual, 06.2017, A5E40912965-1-76 Technical data 6.2 Output 6EP33106SB00-0AY0 6EP33116SB00-0AY0 6EP33206SB00-0AY0 6EP33216SB00-0AY0 6EP33226SB00-0AY0 6EP33216SB10-0AY0 (5 V/3 A) (5 V/6.3 A) (12 V/0.9 A) (12 V/1.9 A) (12 V/4.5 A) (15 V/1.9 A) 0-3A 0 - 6.3 A 0 - 0.9 A 0 - 1.9 A 0 - 4.5 A 0 - 1.9 A 55 ... 70 C: Derating 2 %/K 55 ... 70 C: Derating 2 %/K 55 ... 70 C: Derating 2 %/K 55 ... 70 C: Derating 2 %/K 55 ... 70 C: Derating 2 %/K 55 ... 70 C: Derating 2 %/K 15 W 31.5 W 10.8 W 22.8 W 54 W 28.5 W Can be conYes nected in parallel to increase the power rating Yes No Yes Yes Yes Number of 2 devices that can be connected in parallel, quantity 2 - 2 2 2 see Figure 6-4 Output characteristic (12 V-0.9 A) (Page 62) see Figure 6-3 Output characteristic (Page 61) Current range * Remark Output active power/typical Output characteristic see Figure 6-3 Output characteristic (Page 61) 6EP3322-6SB100AY0 6EP3330-6SB000AY0 6EP3331-6SB000AY0 6EP3332-6SB000AY0 6EP3333-6SB000AY0 (15 V/4 A) (24 V/0.6 A) (24 V/1.3 A) (24 V/2.5 A) (24 V/4 A) Output Regulated, isolated DC voltage Rated output voltage Uout rated DC: 15 V 24 V 24 V 24 V 24 V Total tolerance, static 3% 3% 3% 3% 3% Static line regulation, approx. 0.1 % 0.1 % 0.1 % 0.1 % 0.1 % Static load regulation, approx. 0.1 % 0.1 % 0.1 % 0.1 % 0.1 % Residual ripple peak-peak, max. 200 mV 200 mV 200 mV 200 mV 200 mV Residual ripple peak-peak, typ. 30 mV 30 mV 30 mV 30 mV 30 mV Spikes peak-peak, 300 mV max. (bandwidth, approx. 20 MHz) 300 mV 300 mV 300 mV 300 mV Spikes peak-peak, 50 mV typ. (bandwidth, approx. 20 MHz) 50 mV 50 mV 50 mV 50 mV Setting range - 22.2 - 26.4 V 22.2 - 26.4 V 22.2 - 26.4 V 10.5 - 16.1 V LOGO!Power Manual, 06.2017, A5E40912965-1-76 59 Technical data 6.2 Output 6EP3322-6SB100AY0 6EP3330-6SB000AY0 6EP3331-6SB000AY0 6EP3332-6SB000AY0 6EP3333-6SB000AY0 (15 V/4 A) (24 V/0.6 A) (24 V/1.3 A) (24 V/2.5 A) (24 V/4 A) Product function/output voltage can be adjusted Yes No Yes Yes Yes Output voltage setting Using a potentiometer - Using a potentiometer Using a potentiometer Using a potentiometer Status display Green LED for output voltage OK Response when switching on/off No overshoot of Uout (soft start) Starting delay, max. 0.5 s 0.5 s 0.5 s 0.5 s 0.5 s Voltage rise, typ. 100 ms 100 ms 100 ms 100 ms 100 ms Rated current Iout rated 4A 0.6 A 1.3 A 2.5 A 4A Current range 0-4A 0 - 0.6 A 0 - 1.3 A 0 - 2.5 A 0-4A 55 ... 70 C: Derating 2%/K 55 ... 70 C: Derating 2%/K 55 ... 70 C: Derating 2%/K 55 ... 70 C: Derating 2%/K 55 ... 70 C: Derating 2%/K Output active power/typical 60 W 14.4 W 31.2 W 60 W 96 W Can be connected in parallel to increase the power rating Yes No Yes Yes Yes Number of devices 2 that can be connected in parallel, quantity - 2 2 2 Output characteristic see Figure 6-5 Output characteristic (24 V-0.6 A) (Page 62) see Figure 6-3 Output characteristic (Page 61) * Remark see Figure 6-3 Output characteristic (Page 61) LOGO!Power 60 Manual, 06.2017, A5E40912965-1-76 Technical data 6.2 Output Run-up Figure 6-2 Startup delay/voltage rise Output characteristic for 36 mm, 54 mm and 72 mm devices Figure 6-3 Output characteristic The device supplies a constant output voltage until the current limit is reached. In the event of an overload, the output current and the output voltage are reduced. The device does not switch off. LOGO!Power Manual, 06.2017, A5E40912965-1-76 61 Technical data 6.2 Output Output characteristic for 18 mm devices Output characteristic 12 V devices Figure 6-4 Output characteristic (12 V-0.9 A) Output characteristic for 24 mm devices Figure 6-5 Output characteristic (24 V-0.6 A) The device supplies a constant output voltage until the current limit is reached. In the event of an overload, the output current and the output voltage are reduced. When the output current is exceeded by approximately 1.5x, the device shuts down and automatically restarts after approximately 1 - 1.5 s. This response is repeated as long as the overload condition is present. LOGO!Power 62 Manual, 06.2017, A5E40912965-1-76 Technical data 6.3 Efficiency and power loss 6.3 Efficiency and power loss 6EP33106SB00-0AY0 6EP33116SB00-0AY0 6EP33206SB00-0AY0 6EP33216SB00-0AY0 6EP33226SB00-0AY0 6EP33216SB10-0AY0 (5 V/3 A) (5 V/6.3 A) (12 V/0.9 A) (12 V/1.9 A) (12 V/4.5 A) (15 V/1.9 A) Efficiency at Uout rated, Iout rated, approx. 75 % 78 % 78 % 81 % 87 % 83 % Power loss at Uout rated, Iout rated, approx. 5W 8.7 W 3W 5.4 W 8.2 W 6W 6EP3322-6SB100AY0 6EP3330-6SB000AY0 6EP3331-6SB000AY0 6EP3332-6SB000AY0 6EP3333-6SB000AY0 (15 V/4 A) (24 V/0.6 A) (24 V/1.3 A) (24 V/2.5 A) (24 V/4 A) Efficiency at Uout rated, Iout rated, approx. 88 % 85 % 86 % 90 % 89 % Power loss at Uout rated, Iout rated, approx. 8W 2.6 W 5W 7W 12 W Figure 6-6 6EP3310-6SB00-0AY0 (5 V/3 A) LOGO!Power Manual, 06.2017, A5E40912965-1-76 63 Technical data 6.3 Efficiency and power loss Figure 6-7 6EP3311-6SB00-0AY0 (5 V/6.3 A) Figure 6-8 6EP3320-6SB00-0AY0 (12 V/0.9 A) LOGO!Power 64 Manual, 06.2017, A5E40912965-1-76 Technical data 6.3 Efficiency and power loss Figure 6-9 6EP3321-6SB00-0AY0 (12 V/1.9 A) Figure 6-10 6EP3322-6SB00-0AY0 (12 V/4.5 A) LOGO!Power Manual, 06.2017, A5E40912965-1-76 65 Technical data 6.3 Efficiency and power loss Figure 6-11 6EP3321-6SB10-0AY0 (15 V/1.9 A) Figure 6-12 6EP3322-6SB10-0AY0 (15 V/4 A) LOGO!Power 66 Manual, 06.2017, A5E40912965-1-76 Technical data 6.3 Efficiency and power loss Figure 6-13 6EP3330-6SB00-0AY0 (24 V/0.6 A) Figure 6-14 6EP3331-6SB00-0AY0 (24 V/1.3 A) LOGO!Power Manual, 06.2017, A5E40912965-1-76 67 Technical data 6.3 Efficiency and power loss Figure 6-15 6EP3332-6SB00-0AY0 (24 V/2.5 A) Figure 6-16 6EP3333-6SB00-0AY0 (24 V/4 A) LOGO!Power 68 Manual, 06.2017, A5E40912965-1-76 Technical data 6.4 Closed-loop control 6.4 Closed-loop control 6EP33106SB00-0AY0 6EP33116SB00-0AY0 6EP33206SB00-0AY0 6EP33216SB00-0AY0 6EP33226SB00-0AY0 6EP33216SB10-0AY0 (5 V/3 A) (5 V/6.3 A) (12 V/0.9 A) (12 V/1.9 A) (12 V/4.5 A) (15 V/1.9 A) Dynamic line regulation (Uin rated 15 %) 0.2 % 0.2 % 0.2 % 0.2 % 0.2 % 0.2 % Dyn. load regulation (Iout: 10/90/10 %), Uout typ. 5% 7% 3% 2% 4% 2% Load step regu- 1 ms lation time 10 to 90 %, typ. 1 ms 1 ms 1 ms 1 ms 1 ms Load step regu- 1 ms lation time 90 to 10 %, typ. 1 ms 1 ms 1 ms 1 ms 1 ms 6EP3322-6SB100AY0 6EP3330-6SB000AY0 6EP3331-6SB000AY0 6EP3332-6SB000AY0 6EP3333-6SB000AY0 (15 V/4 A) (24 V/0.6 A) (24 V/1.3 A) (24 V/2.5 A) (24 V/4 A) Dynamic line regu- 0.2 % lation (Uin rated 15 %) 0.2 % 0.2 % 0.2 % 0.2 % Dyn. load regulation (Iout: 10/90/10 %), Uout typ. 3% 2% 1% 2% 2% Load step regulation time 10 to 90 %, typ. 1 ms 1 ms 1 ms 1 ms 1 ms Load step regulation time 90 to 10 %, typ. 1 ms 1 ms 1 ms 1 ms 1 ms LOGO!Power Manual, 06.2017, A5E40912965-1-76 69 Technical data 6.5 Protection and monitoring 6.5 Protection and monitoring 6EP33106SB00-0AY0 6EP33116SB00-0AY0 6EP33206SB00-0AY0 6EP33216SB00-0AY0 6EP33226SB00-0AY0 6EP33216SB10-0AY0 (5 V/3 A) (5 V/6.3 A) (12 V/0.9 A) (12 V/1.9 A) (12 V/4.5 A) (15 V/1.9 A) 8.2 A 1.3 A 2.5 A 5A 2.5 A Constant current characteristic Shutdown, restart after 1 1.5 s Constant current characteristic Constant current characteristic Constant current characteristic 8.2 A 1.3 A 2.5 A 5A 2.5 A Output overvoltage protection Yes, according to EN 60950-1 Current limitation, typ. 3.8 A Property of the output/shortcircuit proof Yes Short-circuit protection Constant current characteristic Continuous 3.8 A short-circuit current/rms value/maximum 6EP3322-6SB100AY0 6EP3330-6SB000AY0 6EP3331-6SB000AY0 6EP3332-6SB000AY0 6EP3333-6SB000AY0 (15 V/4 A) (24 V/0.6 A) (24 V/1.3 A) (24 V/2.5 A) (24 V/4 A) 0.8 A 1.7 A 3.2 A 5A Output overvoltage protection Yes, according to EN 60950-1 Current limitation, typ. 5A Property of the Yes output/short-circuit proof Short-circuit protection Constant current characteristic Shutdown, restart after 1 - 1.5 s Constant current characteristic Constant current characteristic Constant current characteristic Continuous shortcircuit current/rms value/maximum 5A 0.8 A 1.7 A 5A 3.2 A LOGO!Power 70 Manual, 06.2017, A5E40912965-1-76 Technical data 6.6 MTBF 6.6 MTBF 6EP33106SB00-0AY0 6EP33116SB00-0AY0 6EP33206SB00-0AY0 6EP33216SB00-0AY0 6EP33226SB00-0AY0 6EP33216SB10-0AY0 (5 V/3 A) (5 V/6.3 A) (12 V/0.9 A) (12 V/1.9 A) (12 V/4.5 A) (15 V/1.9 A) 2,700,000 3,800,000 2,900,000 2,600,000 2,900,000 Mean Time Between Failures 2,900,000 SN29500 (at 40 C, rated load, 24 h operation) Mean Time Between Failures SN29500 (at 40 C, rated load, 24 h operation) 6EP33226SB10-0AY0 6EP33306SB00-0AY0 6EP33316SB00-0AY0 6EP33326SB00-0AY0 6EP33336SB00-0AY0 (15 V/4 A) (24 V/0.6 A) (24 V/1.3 A) (24 V/2.5 A) (24 V/4 A) 2,600,000 4,400,000 3,100,000 2,900,000 2,400,000 LOGO!Power Manual, 06.2017, A5E40912965-1-76 71 Technical data 6.7 Mechanical system 6.7 Mechanical system 6EP3320-6SB00-0AY0 6EP3310-6SB00-0AY0 6EP3311-6SB00-0AY0 6EP3333-6SB00-0AY0 (12 V/0.9 A) (5 V/3 A) (5 V/6.3 A) (24 V/4 A) 6EP3330-6SB00-0AY0 6EP3321-6SB00-0AY0 6EP3322-6SB00-0AY0 (24 V/0.6 A) (12 V/1.9 A) (12 V/4.5 A) 6EP3321-6SB10-0AY0 6EP3322-6SB10-0AY0 (15 V/1.9 A) (15 V/4 A) 6EP3331-6SB00-0AY0 6EP3332-6SB00-0AY0 (24 V/1.3 A) (24 V/2.5 A) Connection system screw-type terminal Connections / line supply L, N: 1 screw terminal each for 0.14 - 2.5 mm solid/finely stranded L, N: 1 screw terminal each for 0.05 - 2.5 mm solid/finely stranded Connections / output +, -: 1 screw terminal each for 0.14 - 2.5 mm +, -: 2 screw terminals each for 0.05 - 2.5 mm Width of the housing 18 mm 36 mm 54 mm 72 mm Height of the housing 90 mm 90 mm 90 mm 90 mm Depth of the housing 53 mm 53 mm 53 mm 53 mm Installation width 18 mm 36 mm 54 mm 72 mm Mounting height 130 mm 130 mm 130 mm 130 mm Weight, approx. 0.07 kg 0.12 kg 0.2 kg 0.29 kg Product feature / of the Yes housing / housing that can be lined up next to one another Type of mounting / panel mounting Yes Type of mounting / rail mounting Yes Type of mounting / S7-300 rail mounting No Mounting Can be snapped onto standard EN 60715 35x7,5/15 mounting rails LOGO!Power 72 Manual, 06.2017, A5E40912965-1-76 Technical data 6.8 Dimension drawing 6.8 Dimension drawing See Section Dimensions and weight (Page 17) CAD data that can be downloaded from the Internet: 6EP3310-6SB00-0AY0 (http://www.automation.siemens.com/bilddb/index.aspx?gridview=view2&objkey=G_KT01_X X_01275&showdetail=true&view=Search) 6EP3311-6SB00-0AY0 (http://www.automation.siemens.com/bilddb/index.aspx?gridview=view2&objkey=G_KT01_X X_01278&showdetail=true&view=Search) 6EP3320-6SB00-0AY0 (http://www.automation.siemens.com/bilddb/index.aspx?gridview=view2&objkey=G_KT01_X X_01306&showdetail=true&view=Search) 6EP3321-6SB00-0AY0 (http://www.automation.siemens.com/bilddb/index.aspx?gridview=view2&objkey=G_KT01_X X_01281&showdetail=true&view=Search) 6EP3322-6SB00-0AY0 (http://www.automation.siemens.com/bilddb/index.aspx?gridview=view2&objkey=G_KT01_X X_01284&showdetail=true&view=Search) 6EP3321-6SB10-0AY0 (http://www.automation.siemens.com/bilddb/index.aspx?gridview=view2&objkey=G_KT01_X X_01287&showdetail=true&view=Search) 6EP3322-6SB10-0AY0 (http://www.automation.siemens.com/bilddb/index.aspx?gridview=view2&objkey=G_KT01_X X_01290&showdetail=true&view=Search) 6EP3330-6SB00-0AY0 (http://www.automation.siemens.com/bilddb/index.aspx?gridview=view2&objkey=G_KT01_X X_01303&showdetail=true&view=Search) 6EP3331-6SB00-0AY0 (http://www.automation.siemens.com/bilddb/index.aspx?gridview=view2&objkey=G_KT01_X X_01293&showdetail=true&view=Search) 6EP3332-6SB00-0AY0 (http://www.automation.siemens.com/bilddb/index.aspx?gridview=view2&objkey=G_KT01_X X_01296&showdetail=true&view=Search) 6EP3333-6SB00-0AY0 (http://www.automation.siemens.com/bilddb/index.aspx?gridview=view2&objkey=G_KT01_X X_01299&showdetail=true&view=Search) LOGO!Power Manual, 06.2017, A5E40912965-1-76 73 Technical data 6.8 Dimension drawing LOGO!Power 74 Manual, 06.2017, A5E40912965-1-76 7 Safety, approvals, EMC 7.1 Safety 6EP3310-6SB00-0AY0 (5 V/3 A) 6EP3322-6SB10-0AY0 (15 V/4 A) 6EP3311-6SB00-0AY0 (5 V/6.3 A) 6EP3330-6SB00-0AY0 (24 V/0.6 A) 6EP3320-6SB00-0AY0 (12 V/0.9 A) 6EP3331-6SB00-0AY0 (24 V/1.3 A) 6EP3321-6SB00-0AY0 (12 V/1.9 A) 6EP3332-6SB00-0AY0 (24 V/2.5 A) 6EP3322-6SB00-0AY0 (12 V/4.5 A) 6EP3333-6SB00-0AY0 (24 V/4 A) 6EP3321-6SB10-0AY0 (15 V/1.9 A) Primary/secondary galvanic isolation Yes Electrical isolation SELV output voltage Uout acc. to EN 60950-1 and EN 50178 Protection class Class II (without protective conductor) Degree of protection (EN 60529) IP20 Test voltage See Section Test voltage (Page 76) LOGO!Power Manual, 06.2017, A5E40912965-1-76 75 Safety, approvals, EMC 7.2 Test voltage 7.2 Test voltage Figure 7-1 Test voltage diagram Only the manufacturer can perform the type test and production test; users can also perform the field test. Preconditions for performing the field test: Test (A) Connect the input terminals to one another Connect the output terminals to one another Table 7- 1 Test voltage Type test Production test Field test Test time Prim sec (A) 60 s 4200 V DC 60 s 3000 V AC 1s 4200 V DC 1s 3000 V AC 1s 2200 V DC 1s 1500 V AC Remark: Tripping current for DC measurement: 0 mA Tripping current for AC measurement: < 100 mA LOGO!Power 76 Manual, 06.2017, A5E40912965-1-76 Safety, approvals, EMC 7.3 Certifications 7.3 Certifications Certifications 6EP3310-6SB00-0AY0 (5 V/3 A) 6EP3320-6SB00-0AY0 (12 V/0.9 A) 6EP3311-6SB00-0AY0 (5 V/6.3 A) 6EP3321-6SB00-0AY0 (12 V/1.9 A) 6EP3322-6SB00-0AY0 (12 V/4.5 A) 6EP3333-6SB00-0AY0 (24 V/4 A) 6EP3321-6SB10-0AY0 (15 V/1.9 A) 6EP3322-6SB10-0AY0 (15 V/4 A) 6EP3331-6SB00-0AY0 (24 V/1.3 A) 6EP3330-6SB00-0AY0 (24 V/0.6 A) 6EP3332-6SB00-0AY0 (24 V/2.5 A) CE marking Yes Yes UL/cUL approval cULus-Listed (UL 508, CSA C22.2 No.107.1), File E197259 NEC class2 (to UL 60950-1/UL 1310), File E151273 UL/CSA approval Yes cULus-Listed (UL 508, CSA C22.2 No.107.1), File E197259 cURus-Recognized (UL 60950-1, CSA C22.2 No. 60950-1) File E151273 CSA 22.2 N060950 cCSAus FM Class I, Div. 2, Group ABCD, T4 being prepared CB approval Yes Explosion protection IECEx approval Yes ATEX II 3G Ex ic nA IIC T4 ATEX II 3G Ex ic nA IIC T3 UL/cUL: ANSI/ISA12.12.01-2015) Class I, Div. 2, Group ABCD, T4 UL/cUL: ANSI/ISA-12.12.01-2015) Class I, Div. 2, Group ABCD, T4 Yes Yes Yes EC 61000-4-11 EC 61000-4-11 SEMI F47 compliance 208 V-240 V IEC 61000-4-11 Marine approval Yes 6EP3310-6SB00-0AY0, 6EP3311-6SB00-0AY0, 6EP3320-6SB00-0AY0 6EP3321-6SB00-0AY0, 6EP3322-6SB00-0AY0 DNV-GL, ABS being prepared 6EP3321-6SB10-0AY0, 6EP3322-6SB10-0AY0, 6EP3330-6SB00-0AY0 6EP3331-6SB00-0AY0, 6EP3332-6SB00-0AY0, 6EP3333-6SB00-0AY0 DNV-GL, ABS, BV, LRS being prepared LOGO!Power Manual, 06.2017, A5E40912965-1-76 77 Safety, approvals, EMC 7.4 EMC 7.4 EMC 6EP3310-6SB00-0AY0 (5 V/3 A) 6EP3311-6SB00-0AY0 (5 V/6.3 A) 6EP3320-6SB00-0AY0 (12 V/0.9 A) 6EP3321-6SB00-0AY0 (12 V/1.9 A) 6EP3322-6SB00-0AY0 (12 V/4.5 A) 6EP3321-6SB10-0AY0 (15 V/1.9 A) 6EP3322-6SB10-0AY0 (15 V/4 A) 6EP3330-6SB00-0AY0 (24 V/0.6 A) 6EP3331-6SB00-0AY0 (24 V/1.3 A) 6EP3332-6SB00-0AY0 (24 V/2.5 A) 6EP3333-6SB00-0AY0 (24 V/4 A) Generic standards EN 61000-6-2 Immunity for industrial environments EN 61000-6-3 Emission for residential areas Electrostatic discharges EN 61000-4-2 8 kV contact, 8 kV air Electromagnetic fields EN 61000-4-3 80 - 1000 MHz 10 V/m 1000 - 2000 MHz 3 V/m 2000 - 2700 MHz 1 V/m High-speed transient disturbance variables (burst) EN 61000-4-4 Power surges EN 61000-4-5 4 kV on line connections 2 kV at DC output 2 kV symmetrical on line connections 4 kV asymmetrical on line connections 500 V symmetrical/asymmetrical on DC output cables High-frequency fields EN 61000-4-6 10 V; 0.15 - 80 MHz Voltage dips EN 61000-4-11 100% for 20 ms 60% for 200 ms 30% for 500 ms Voltage interruptions EN 61000-4-11 100% for 5000 ms Emitted interference EN 55022 Class B Line harmonics limitation EN 61000-3-2 Not applicable Noise immunity EN 61000-6-2 LOGO!Power 78 Manual, 06.2017, A5E40912965-1-76 8 Ambient conditions 6EP3310-6SB00-0AY0 (5 V/3 A) 6EP3322-6SB10-0AY0 (15 V/4 A) 6EP3311-6SB00-0AY0 (5 V/6.3 A) 6EP3330-6SB00-0AY0 (24 V/0.6 A) 6EP3320-6SB00-0AY0 (12 V/0.9 A) 6EP3331-6SB00-0AY0 (24 V/1.3 A) 6EP3321-6SB00-0AY0 (12 V/1.9 A) 6EP3332-6SB00-0AY0 (24 V/2.5 A) 6EP3322-6SB00-0AY0 (12 V/4.5 A) 6EP3333-6SB00-0AY0 (24 V/4 A) 6EP3321-6SB10-0AY0 (15 V/1.9 A) Ambient temperature -25 ... 70 C for natural convection (self convection) Tested according to: Transport and storage temperature * EN 60068-2-1 Cold * EN 60068-2-2 Dry heat * EN 60068-2-78 Humid heat, constant * EN 60068-2-14 Temperature change -40 ... 85 C Tests (packed for shipping) according to: * EN 60068-2-1 Cold * EN 60068-2-2 Dry heat * EN 60068-2-30 Humid heat, cyclic Humidity class Climatic class 3K3 according to EN 60721, 5 - 95 % no condensation Degree of pollution 2 Mechanical stressing in operation Tested according to: * * EN 60068-2-6 Vibration, test Fc - 7 mm deflection in the range 5 - 9 Hz - 2 g acceleration in the range 9 - 150 Hz EN 60068-2-27 Shock, test Ea - Acceleration 150 m/s2, test duration 11 ms LOGO!Power Manual, 06.2017, A5E40912965-1-76 79 Ambient conditions 6EP3310-6SB00-0AY0 (5 V/3 A) 6EP3322-6SB10-0AY0 (15 V/4 A) 6EP3311-6SB00-0AY0 (5 V/6.3 A) 6EP3330-6SB00-0AY0 (24 V/0.6 A) 6EP3320-6SB00-0AY0 (12 V/0.9 A) 6EP3331-6SB00-0AY0 (24 V/1.3 A) 6EP3321-6SB00-0AY0 (12 V/1.9 A) 6EP3332-6SB00-0AY0 (24 V/2.5 A) 6EP3322-6SB00-0AY0 (12 V/4.5 A) 6EP3333-6SB00-0AY0 (24 V/4 A) 6EP3321-6SB10-0AY0 (15 V/1.9 A) Damaging gases Atmospheric pressure Tested according to: * EN 60068-2-42 Sulfur dioxide: 10 cm3/m3, 4 days * EN 60068-2-43 Hydrogen sulfide: 1 cm3/m3, 4 days Operation: * 1080 - 795 hPa (-1000 - 2000 m) * For operation at altitudes of 2000 m up to 6000 m above sea level: output power must be derated by -7.5% / 1000 m or the ambient temperature must be reduced by 5 K / 1000 m see Figure 4-12 Mounting height derating (Page 27) Overvoltage category: III up to 2000 m (EN 50178) II from 2000 m up to 6000 m (EN 50178) Storage: * * 1080 - 660 hPa (-1000 - 3500 m) LOGO!Power 80 Manual, 06.2017, A5E40912965-1-76 9 Applications 9.1 Parallel connection to increase power rating To enhance performance, two LOGO!Power power supplies of the same type can be galvanically connected in parallel. Note It is not permissible to connect 6EP3320-6SB00-0AY0 (12 V/0.9 A) and 6EP3330-6SB000AY0 (24 V/0.6 A) in parallel. The following must be observed: The cables connected to each power supply at terminals "+" and "-" must have identical lengths and the same cable cross-sections (or the same impedance) up to a common external network junction (terminal strip) if possible. The power supplies connected in parallel must be switched on simultaneously with a common switch in the line feeder cable (e.g. with the main switch available in control cabinets). The output voltages measured in no-load operation for the power supplies that are not yet connected in parallel should not deviate more than a maximum of 0.2 %. This usually corresponds to the factory setting. If the output voltage is changed, you should connect the "-" terminals and then, in no-load operation, measure the voltage difference between the "+" terminals that have not yet been connected. This voltage difference should not exceed 0.2 % of Uout. Figure 9-1 Parallel connection, correct and incorrect LOGO!Power Manual, 06.2017, A5E40912965-1-76 81 Applications 9.1 Parallel connection to increase power rating NOTICE Protective circuit for the parallel connection of more than two power supplies For connection of more than two power supplies in parallel, additional measures must be taken to prevent high backward feeding currents in the event of a secondary device fault. For this purpose, a suitable protective circuit (e.g. decoupling diode or DC-conform circuit-breaker) must be installed between each "+" terminal of the power supply and the common connection point. LOGO!Power 82 Manual, 06.2017, A5E40912965-1-76 Applications 9.2 Parallel connection for redundancy 9.2 Parallel connection for redundancy The parallel switching of several LOGO!Power power supplies of the same type for redundancy is required when the demands for reliability of the supply are particularly high. If a component in the redundant supply fails, the power supply for the loads must be fully accommodated by the remaining component. It is therefore important when dimensioning the system to make sure that n+1 redundant switched power supplies can handle the total power requirement of the remaining n power supplies. To prevent loading of the remaining power supplies in the event of a secondary-side error when one power supply fails, the respective "+" terminals of the power supplies must be decoupled via diodes. Note For a high reliability of the supply, it is recommended that the redundant switched power supplies are fused separately on the line-side and, if possible, be connected to different power supply networks. Figure 9-2 Parallel connection for redundancy LOGO!Power Manual, 06.2017, A5E40912965-1-76 83 Applications 9.3 Series connection for increased voltage 9.3 Series connection for increased voltage To achieve a higher output voltage, two LOGO!Power power supplies of the same type can be connected in series. In this case, connect the "-" terminal of the first power supply to the "+" terminal of the second power supply. The "+" terminal of the first power supply and the "-" terminal of the second power supply are routed to the load. Depending on grounding point of the secondary output voltage, voltages of +2xUA, UA or -2xUAcan be implemented. In the case of asymmetric load distribution, it is not possible to ensure correct functionality. WARNING SELV is not guaranteed in the case of a fault When connecting two power supplies in series, the continuous, permissible SELV voltage of a maximum of 60 VDC according to EN 60950 cannot be guaranteed in the case of a fault. Figure 9-3 Series connection LOGO!Power 84 Manual, 06.2017, A5E40912965-1-76 Applications 9.4 Protection against short-time voltage dips 9.4 Protection against short-time voltage dips During a drop in the primary-side supply voltage, the LOGO!Power power supplies still maintain the output voltage over a short millisecond period (see Section Technical data (Page 55) Power failure buffering). LOGO!Power Manual, 06.2017, A5E40912965-1-76 85 Applications 9.4 Protection against short-time voltage dips LOGO!Power 86 Manual, 06.2017, A5E40912965-1-76 Environment 10 The devices are in conformance with RoHS. As a rule, only non-silicon precipitating materials are used. Disposal guidelines Packaging and packaging aids can and should always be recycled. The product itself may not be disposed of as domestic refuse. LOGO!Power Manual, 06.2017, A5E40912965-1-76 87 Environment LOGO!Power 88 Manual, 06.2017, A5E40912965-1-76 Service & Support 11 Technical support Technical support for all IA/DT products can be accessed through the following communication channels: Telephone: + 49 (0) 911 895 7222 Internet: Online support request form (http://www.siemens.de/automation/support-request) Technical documentation on the Internet Operating instructions and manuals for SITOP are available in the Internet: Operating instructions/manuals (http://www.siemens.com/sitop/manuals) SITOP power supply homepage General news about our power supplies is available in the Internet at the SITOP home page: SITOP (http://www.siemens.com/sitop) Information material SITOP information can be downloaded from the Internet: Information and download center (http://www.siemens.com/sitop-infomaterial) CAx data 2D/3D data and circuit diagram macros can be downloaded from the Internet: Siemens image database (http://www.siemens.com/sitop-cax) Request all CAx data via the CAx download manager: CAx shopping cart (http://www.siemens.com/cax) SITOP Selection Tool Simply and quickly select the optimum the power supply or DC-UPS: SITOP Selection Tool (http://www.siemens.com/sitop-selection-tool) Online catalog and ordering system The online catalog and the online ordering system are available through the Industry Mall homepage: Industry Mall (http://www.siemens.com/industrymall/de) LOGO!Power Manual, 06.2017, A5E40912965-1-76 89 Service & Support Contact persons If you have any questions regarding the use of our products, then contact the Siemens contact person in your regional Siemens sales office. You can find these addresses as follows: On the Internet (http://www.automation.siemens.com/partner) In Catalog CA 01 LOGO!Power 90 Manual, 06.2017, A5E40912965-1-76