THC63LVDM83C-5S - THine Electronics, Inc.

THC63LVDM83C(5S) _Rev.1.10_E

Security E

Block Diagram

7

THC63LVDM83C(5S)

REDUCED SWING LVDS 24Bit COLOR HOST-LCD PANEL INTERFACE

General Description

The THC63LVDM83C(5S) transmitter is desi gned to

support pixel data transmission between Host and Flat

Panel Display from NTS C up to SXGA+ resolut ions.

The THC63LVDM83C(5S) converts 28bits of CMOS/

TTL data into LVDS(Low Voltage Differential Signal-

ing) data stream. The transmitter can be programmed

for rising edge or falling edge clocks through a dedi-

cated pin. At a transmit clock frequency of 85MHz,

24bits of RGB data and 4bits of timing and control data

(HSYNC, VSYNC, CNTL1, CNTL2) are transmitted at

an effective rate of 595Mbps per LV DS channel.

Features

•Wide dot clock range: 8-85MHz suited for NTSC,

VGA, SVGA, XGA

•PLL requires no external components

•Supports spread spectrum clock generator

•On chip jitter filtering

•Clock edge selectable

•Supports reduced swing LVDS for low EMI

•Power down mode

•Low power single 3.3V CMOS design

•Low profile 56 Lead TSSOP Package

•1.2 up to 3.3V tolerant data inputs to connect

directly to low power,low voltage application and

graphic processor.

•Backward compatible with

THC63LVDM83R(24bits)

TTL PARALLEL TO SE RIAL

PLL

TA +/-

TB +/-

TC +/-

TD +/-

TCLK +/-

R/F

/PDWN

TA0-6

TC0-6

TD0-6

TRANSMITTER

(8 to 85MHz)

CMOS/TTL

7

RS

7

TB0-6 7

INPUTS

CLOCK

(LVDS)

8-85MHz

DATA

(LVDS)

(56-595Mbit/On Each

LVDS Channel)

CLKIN

THC63LVDM83C(5S)

THC63LVDM83C(5S)_Rev.1.10_E

Security E

Pin Out

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

56

55

54

53

52

51

50

49

48

47

46

45

44

43

42

41

40

39

38

37

36

35

34

33

32

31

30

29

RS

TD1

TA5

TA6

GND

TB0

TB1

TD2

VCC

TD3

TB2

TB3

GND

TB4

TB5

TD4

R/F

TD5

TB6

TC0

GND

TC1

TC2

TC3

TD6

VCC

TC4

TC5

TA4

TA3

TA2

GND

TA1

TA0

TD0

LVDS GND

TA-

TA+

TB-

TB+

LVDS VCC

LVDS GND

TC-

TC+

TCLK-

TCLK+

TD-

TD+

LVDS GND

PLL GND

PLL VCC

PLL GND

/PDWN

CLK IN

TC6

GND

THC63LVDM83C(5S)

THC63LVDM83C(5S)_Rev.1.10_E

Security E

Pin Description

Pin Name Pin # Type Description

TA+, TA- 47, 48 LVDS OUT

LVDS Data Out.

TB+, TB- 45, 46 LVDS OUT

TC+, TC- 41, 42 LVDS OUT

TD+, TD- 37, 38 LVDS OUT

TCLK+, TCLK- 39, 40 LVDS OUT LVDS Clock Out.

TA0 ~ TA6 51, 52, 54, 55, 56, 3, 4 IN

Pixel Data Inputs.

TB0 ~ TB6 6, 7, 11, 12, 14, 15, 19 IN

TC0 ~ TC6 20, 22, 23, 24, 27, 28, 30 IN

TD0 ~ TD6 50, 2, 8, 10, 16, 18, 25 IN

/PDWN 32 IN H: Normal operation,

L: Power down (all outputs are Hi-Z)

RS 1 IN

LVDS swing mode, VREF select.

R/F 17 IN Input Clock Triggering Edge Select.

H: Rising edge, L: Falling edge

VCC 9, 26 Power Power Supply Pins for TTL inputs and digital

circuitry.

CLKIN 31 IN Clock in.

GND 5, 13, 21,

29, 53 Ground Ground Pins for TTL inputs and digital circuitry.

LVDS VCC 44 Power Power Supply Pins for LVDS Outputs.

LVDS GND 36, 43, 49 Ground Ground Pins for LVDS Outputs.

PLL VCC 34 Power Power Supply Pin for PLL circuitry.

PLL GND 33, 35 Ground Ground Pins for PLL circuitry.

RS LVDS

Swing Small Swing

Input Support

VCC 350mV N/A

0.6 ~ 1.4V 350mV RS=VREFa

a. VREF is Input Reference Voltage.

GND 200mV N/A

THC63LVDM83C(5S) _Rev.1.10_E

Security E

Absolute Maximum Ratings 1

Recommended Operating Conditions

Supply Voltage (VCC)-0.3V ~ +4.0V

CMOS/TTL Input Voltage -0.3V ~ (VCC + 0.3V)

CMOS/TTL Outp ut Voltage -0.3V ~ (VCC + 0.3V)

LVDS Driver Output Voltage -0.3V ~ (VCC + 0.3V)

Output Current continuous

Junction Temperature +125

Storage Temperature Range -55 ~ +150

Resistance to soldering heat +260 /10sec

Maximum Power Dissipation @+25 0.5W

1. “Absolute Maximum Ratings” are those valued beyond which the safety of the device can not be guaranteed. They

are not meant to imply that the device should be operated at these limits. The tables of “Electrical Characteristics”

specify conditions for device operation.

Parameter Min Typ Max Units

All Supply Voltage 3.0 3.3 3.6 V

Operating Ambient Temperature -40 85

CLK IN Frequency 8 85 MHz

°C

°C°C

°C

THC63LVDM83C(5S)_Rev.1.10_E

Security E

Electrical Characteristics

CMOS/TTL DC Specifications VCC = VCC = PLL VCC = LVDS VCC

Notes: 1VDDQ voltage defines max voltage of small swing input. It is not an actual input voltage.

2 Small swing signal is applied to TA0-6,TB0-6,TC0-6,TD0-6 and CLKIN.

LVDS Transmitter DC Specifications VCC = VCC = PLL VCC = LVDS VCC

Symbol Parameter Conditions Min. Typ. Max. Units

VIH High Level Input Voltage RS=VCC or GND 2.0 VCC V

VIL Low Level Input Voltage RS=VCC or GND GND 0.8 V

VDDQ1Small Swing Voltage 1.2 2.8 V

VREF Input Reference Voltage Small Swing (RS=VDDQ/2) VDDQ/2

VSH2Small Swing High Level

Input Voltage VREF = VDDQ/2 VDDQ/2

+100mV V

VSL2Small Swing Low Level

Input Voltage VREF = VDDQ/2 VDDQ/2

-100mV V

IINC Input Current uA

Symbol Parameter Conditions Min. Typ. Max. Units

VOD Differential Output Voltage RL=100Ω

Normal

swing

RS=VCC

250 350 500 mV

Reduced

swing

RS=GND 100 200 300 mV

ΔVOD Change in VOD between

complementary output states RL=100Ω

35 mV

VOC Common Mode Voltage 1.125 1.25 1.375 V

ΔVOC Change in VOC between

complementary output states 35 mV

IOS Output Short Circuit Current VOUT=0V, RL=100Ω-24 mA

IOZ Output TRI-STATE Current /PDWN=0V,

VOUT=0V to VCC uA

0V VIN VCC

≤≤ 10±

10±

THC63LVDM83C(5S)_Rev.1.10_E

Security E

Supply Current VCC = VCC = PLL VCC = LVDS VCC

Symbol Parameter Condition(*) Typ. Max. Units

ITCCG Transmitter Supply

Current

RL=100Ω,CL=5pF

VCC=3.3V, f=85MHz

Gray Scale Pattern

RS=VCC 52 58 mA

RS=GND 40 46 mA

ITCCW Transmitter Supply

Current

RL=100Ω,CL=5pF

VCC=3.3V, f=85MHz

Worst Case Pattern

RS=VCC 61 67 mA

RS=GND 50 56 mA

ITCCS Transmitter Power

Down Supply Current /PDWN = L 10 uA

CLK

Tx1

Tx2

Tx3

Tx4

Tx5

Tx6

x= A, B, C, D

Fig1. Data Pattern

CLK

Tx1

Tx2

Tx3

Tx4

Tx5

Tx6

x= A, B, C, D

Worst Case Pattern

Gray Scale Pattern

THC63LVDM83C(5S)_Rev.1.10_E

Security E

Switching Characteristics VCC = VCC = PLL VCC = LVDS VCC

Symbol Parameter Min. Typ. Max. Units

tTCIT CLK IN Transition time 5.0 ns

tTCP CLK IN Period 11.7 T 125 ns

tTCH CLK IN High Time 0.35T 0.5T 0.65T ns

tTCL CLK IN Low Time 0.35T 0.5T 0.65T ns

tTCD CLK IN to TCLK+/- Delay 3T ns

tTS TTL Data Setup to CLK IN 2.5 ns

tTH TTL Data Hold from CLK IN 0 ns

tLVT LVDS Tr an sit ion Time 0.6 1.5 ns

tTOP1 Output Data Position0 (T=11.7ns) -0.2 0.0 +0.2 ns

tTOP0 Output Data Position1 (T=11.7ns) ns

tTOP6 Output Data Position2 (T=11.7ns) ns

tTOP5 Output Data Position3(T=11.7ns) ns

tTOP4 Output Data Position4 (T=11.7ns) ns

tTOP3 Output Data Position5 (T=11.7ns) ns

tTOP2 Output Data Position6 (T=11.7ns) ns

tTPLL Phase Lock Loop Set 10.0 ms

T

7

--- 0.2–T

7

--- T

7

--- 0.2+

2T

7

--- 0.2–2T

7

--- 2 T

7

--- 0.2+

3T

7

--- 0.2–3T

7

--- 3 T

7

--- 0.2+

4T

7

--- 0.2–4T

7

--- 4 T

7

--- 0.2+

5T

7

--- 0.2–5T

7

--- 5 T

7

--- 0.2+

6T

7

--- 0.2–6T

7

--- 6 T

7

--- 0.2+

AC Timing Dia grams

TTL Inpu t

5pF 20%

80%

20%

80%

tLVT tLVT

CLK IN

LVDS Output

90%

10%

90%

10%

tTCIT tTCIT

Vdiff

100Ω

Vdiff=(TA+)-(TA-)

TA+

TA-

LVDS Output L oad

Fig2. CLKIN Transition Time

Fig3. LVDS Output Load and Transi ti on Time

THC63LVDM83C(5S)_Rev.1.10_E

Security E

TTL Inputs tTCP

tTS tTH

tTCH

tTCL

CLK IN

Tx0-Tx6

tTCD

Note:

CLK IN: fo r R/F=GND, denote as soli d line,

for R/F=VCC, denote as dashed line.

TCLK+

TCLK-

Small Swing Inputs tTCP

tTS tTH

tTCH

tTCL

CLK IN

Tx0-Tx6

tTCD

Not e:

CLK IN: for R/F=GN D, denote as solid l ine,

for R/F=VC C, denote as das hed li ne.

TCLK+

TCLK-

VDDQ

GND

VDDQ

VREF

VOC

VREF

VCC/2 VCC/2

VDDQ

/2 VDDQ/2

VDDQ/2 VDDQ/2 VDDQ/2

VCC/2

Fig 4. CL KIN Period, High/Low Time, Setup/Ho ld Tim in g

Fig5. Small S wing In pu ts

VCC

GND

VCC

VOD

RS Pin VOD

VCC 350mV

0.6~1.4V

GND 200mV

RS Pin VREF

VCC

0.6~1.4V

GND VCC/2

Input Voltage of RS pin

VCC/2

THC63LVDM83C(5S)_Rev.1.10_E

Security E

AC Timing Diagrams

Phase Lock Loop Set Time

Vdiff = 0 V Vdiff = 0 V

TCLK+/-

tTOP1

tTOP0

tTOP6

tTOP5

tTOP4

tTOP3

tTOP2

LVDS Output

TD6 TD5 TD4 TD3 TD2 TD1 TD0

TD+/-

TC6 TC5 TC4 TC3 TC2 TC1 TC0

TC+/-

TB6 TB5 TB4 TB3 TB2 TB1 TB0

TB+/-

TA6 TA5 TA4 TA3 TA2 TA1 TA0

TA+/-

(Differential)

Ne xt Cycl e

Prev ious Cy cle

Fig6 . L VDS Output Da ta Positio n

2.0V

CLKIN

/PDWN

TCLK+/-

3.0V 3.6V

VCC tTPLL

Vdiff = 0 V

Fig7. PLL Lock Set Tim e

THC63LVDM83C(5S) _Rev.1.10_E

Security E

Note

1)Cable Connection and Disconnection

Don't connect and disconnect the LVDS cable, when the power is supplied to the system.

2)GND Connection

Connect the each GND of the PCB which THC63LVDM83C(5S) and LVDS-Rx on it. It is better for EMI reduction to

place GND cable as close to LVDS cable as possible.

3)Multi Drop Connection

Multi drop connection is not recom mended.

4)Asynchronous use

Asynchronous use such as following systems are not recommende d.

TCLK+

TCLK-

THC63LVDM83C(5S)

LVDS-Rx

TCLK+

TCLK-

TCLK+

TCLK-

CLKOUT

TCLK-

DATA

IC

CLKOUT

DATA

CLKOUT

DATA

IC

TCLK+

TCLK-

THC63LVDM83C(5S)

TCLK+

TCLK-

THC63LVDM83C(5S)

IC

LVDS-Rx

THC63LVDM83C(5S)

CLKOUT

DATA

CLKOUT

DATA

IC

THC63LVDM83C(5S) _Rev.1.10_E

Security E

Package

56 Lead Molded Thin Shrink Small Outline Package, JEDEC

(1.0)

0.10 0.05±

1.2 MAX

0.20 TYP0.50 TYP

8.1 0.1±

4.05

128

6.1 0.1±

14.0 0.1±

2956

Unit : millimeters

THC63LVDM83C(5S)_Rev.1.10_E

Security E

Notices and Requests

1. The product specifications described in this material are subject to change without prior notice.

2. The circuit diagrams described in this material are examples of the application which may not

always apply to the customer's design. We are not responsible for possible errors and omissions

in this material. Please note if errors or omissions should be found in this material, we may not

be able to correct them immediately.

3. This material contains our copy right, know-how or other proprietary. Copying or disclosing to

third parties the contents of this material without our prior permission is prohibited.

4. Note that if infringement of any third party's industrial ownership should occur by using this

product, we will be exempted from the responsibility unless it directly relates to the production

process or functions of the product.

5. Product Application

5.1 Application of this product is intended for and limited to the following applications: audio-

vide deice, officce automation device, communication device, consumer electronics, smart-

phone, feature phone, and amusement machinedevice. This product must not be used for appli-

cations that require extremely high-reliability/safety such as aerospace device, traffic device,

transportation device, nuclear power control device, combustion chamber device, medical

device related to critical care, or any kind of safety device.

5.2 This product is not intended to be used as an automotive part, unless the product is specified

as a product conforming to the demandes and specifications of ISO/TS16949 (“the specified

Product”) in this data sheet. THine Electronics, Inc.(“THine”) accepts no liability what so every

for any product other than the Specified Product for it not conforming to the aforementioned

demands and specifications.

5.3 THine accepts liability for demands and specifications of the Specified Product only to the

extent that the user and THine have been previously and explicitly agreed to each other.

6. Despite our utmost efforts to improve the quality and reliability of the product, faults will occur

with a certain small probability, which is inevitable to a semi-conductor product. Therefore, you

are encouraged to have sufficiently redundant or error preventive design applied to the use of the

product so as not to have our product cause any social or public damage.

7. Please note that this product is not designed to be radiation-proof.

8. Customers are asked, if required, to judge by themselves if this product falls under the category

of strategic goods under the Foreign Exchange and Foreign Trade Control Law.

THine Electronics, Inc.

E-mail: sales@thine.co.jp