DR-11525 16-BIT HIGH FREQUENCY HYBRID DIGITAL-TO-RESOLVER D/R CONVERTER FEATURES DESCRIPTION The DR-11525 is a versatile multiplying digital-to-resolver converter. The digital input represents an angle, and the output is resolver type, sin/cos. The reference input will accept any waveform, even a sawtooth for CRT drive. Because the reference is dccoupled to the output, the DR-11525 can be used as: a digital-to-resolver converter using a sinusoidal reference as an input; a digital-to-sin/cos dc converter using a dc reference; or a polar-to-rectangular converter using a reference input proportional to the radius vector; or a rotating cartwheel sweep generator for PPI displays using a sawtooth reference. Packaged in a 36-pin DDIP, the DR11525 is a complete D/R converter in one hybrid module. Hybrid technology results in low weight, low power consumption, very high reliability, and a wide operating temperature range. The DR-11525 circuit design allows for higher accuracy and reduces the output scale factor variation so that the output * Accuracy Up to 1 Minute can drive displays directly. The output line-to-ground voltage can be scaled by external resistors. The DR-11525 also includes high ac and dc common mode rejection at the reference input * Operational Up to 10 kHz * 2 Vrms, 6.81 Vrms, 11.8 VL-L, or Scalable Resolver Outputs * 2 mA rms Output APPLICATIONS * 16-Bit Resolution Because of its high reliability, small size and low power consumption, the hybrid DR-11525 is ideal for the most stringent and severe industrial and military ground or avionics applications. All units are available with MIL-PRF-38534 processing as a standard option. * 8-Bit/2-Byte Double Buffered Transparent Latches * DC-Coupled Reference Accepts Any Waveform Among the many possible applications are computer-based systems in which digital angle information is processed, such as synchro/resolver simulators, flight trainers, flight instrumentation, fire control systems, IR, radar and navigation systems. In addition, the DR-11525 is ideal for motor and robotic control test systems. * High-Rel CMOS D/R Chip * No +5 V Supply Required TEST POINT - R REFERENCE INPUTS 13.37 k DIFFERENTIAL (NOTE 1) 36.71 k RESOLVER OUTPUTS 49.92 k D/R CONVERTER +S HIGH ACCURACY LOW SCALE FACTOR VARIATION +C S1 26 V 13.37 k 36.71 k 49.92 k S2 REFERENCE CONDITIONER RESOLVER SCALING OUTPUT AMPLIFIERS BITS 1-16 SINGLE-ENDED (NOTE 2) 26 V S4 TRANSPARENT LATCH TRANSPARENT LATCH ADJUSTABLE (NOTE 3) 4.4 V LA LM BITS 1-8 BITS 9-16 DIGITAL INPUT NOTES: 1) 26 VRMS REFERENCE IN = 11.8 VL-L DIFFERENTIAL OUTPUT 2) 26 VRMS REFERENCE IN = 6.8 VRMS SINGLE-ENDED OUTPUT 3) 4.4 VRMS REFERENCE IN = 2 VRMS SINGLE-ENDED OUTPUT FIGURE 1. DR-11525 BLOCK DIAGRAM (c) 1996, 1999 Data Device Corporation S3 LL TABLE 1. DR-11525 SPECIFICATIONS Apply over temperature range, power supply range, reference voltage and frequency range, and 10% harmonic distortion in the reference. INTRODUCTION As shown in FIGURE 1, the signal conversion in the DR-11525 is performed by a high-accuracy digital-to-resolver converter whose sin and cos outputs have a low scale factor variation as a function of the digital input angle. This resolver output is amplified by scaling amplifiers for resolver output. The output line currents can be 2 mA rms max, which is sufficient for driving R/D converters, solid-state control transformers, and displays. Output power amplifiers will be required, however, for driving electromechanical devices such as synchros and resolvers. UNIT VALUE PARAMETER RESOLUTION Bits 16 ACCURACY and DYNAMICS Minutes 4 to 1 min. (See Ordering info.) Output Accuracy 1 minute part: 1 min up to 1 kHz, 1.5 min for 1 to 5 kHz, and 3 min for 5 to 10 kHz (guaranteed by design - tested at 5 kHz) LSB 1 max Differential Linearity sec Less than 20 for any digital step change Output Setting Time DIGITAL INPUT Logic Type Natural binary angle, parallel positive logic CMOS and TTL compatible. Inputs are CMOS transient protected. Logic 0 = 0 to +1 V Logic 1 = +2.2 V to +5 V Load Current A 20 max to GND (bits 1-16) 20 max to +5 V (LL, LM, LA) See Timing Diagram (FIGURE 2.). REFERENCE INPUT Type Frequency Range Hz Three differential solid-state inputs: two for standard 26 V, one programmable. DC to 10 k Standard Input Voltage (Note 1) RH3-RL3 RH2-RL2 RH-RL V V V 4.4 26 26 Input Impedance Single-Ended:RH-gnd k ohm Differential: RH to RL k ohm ANALOG OUTPUT Type Output Current mA rms Standard Output Voltage (Note 2) RH-RL VrmsL-L RH2-RL2 Vrms RH3-RL3 Vrms % Transform. Ratio Tol. % Scale Factor Variation DC Offset mV Single ended The reference conditioner has a differential input with high ac and dc common mode rejection, so that a reference isolation transformer will seldom be required. There are three sets of reference inputs which provide three different input/output ratios. The RHRL input provides a 0.45 ratio between the reference input and the signal output and is designed to provide 11.8 VL-L differential output for a 26 Vrms reference input. The RH2-RL2 input provides a 0.52 ratio between the reference input and the signal output and is designed to provide a 6.81 Vrms single-ended output for a 26 Vrms reference input. The RH3-RL3 input provides a 0.91 ratio between the reference input and the signal output and is designed to provide a 2 Vrms single-ended output for a 4.4 Vrms reference input. Series resistors can be added to accommodate higher reference levels or to reduce the output level. The reference conditioner output -R is intended for test purposes. For a 26 Vrms nominal input to RH, RL, -R should be 5.9 Vrms. 100 0.5% 200 0.5% The timing relationship of LL, LM, and LA is shown in FIGURE 2 as a design reference. Resolver 2 max (Tracks Reference Input Voltage) OUTPUT SCALING AND REF. LEVEL ADJUSTMENT 11.8 nominal 6.81 (single ended) 2.0 nominal (single ended) 0.5 max 0.1 max The DR-11525 operates like a multiplying D/A converter in that the voltage of each output line is directly proportional to the reference voltage. Reference FIGURE 3. The magnitude of the resistors, R', in ohms is calculated as follows: 15 max Varies with input angle. POWER SUPPLIES Voltage V +15 5% +18 V Max voltage without damage Current or Impedance mAmax 35+ load current TEMPERATURE RANGES (CASE) Operation -1 Option C -55 to +125 -3 Option C 0 to +70 Storage C -55 to +135 For RH-RL: VOUTL-L -15 5% -18 V 35+ load current VIN 45.38k = 100k + R' 200 ns MIN TRANSPARENT LATCHED PHYSICAL CHARACTERISTICS Type 36 pin DDIP in.(mm) Size 0.78 x 1.9 x 0.21 (19.7 x 48.1 x 5.3) oz (g) Weight 0.85 (24) ,,, ,, DATA 1-16 BITS Notes: 1) Maximum reference input RH-RL = 26 V +10%; RH2-RL2 = 26 V +10%; RH3-RL3 = 16.4 V. 2) Minumum voltage output (when using scalable reference input) is 1 V differential or 0.5 V single ended. 3) Differential is line-to-line (L-L); single ended is line-to-ground (L-gnd). 50 ns MIN 100 ns MIN FIGURE 2. LL, LM, LA TIMING DIAGRAM 2 *For RH2-RL2: VOUTL-L 45.38k smooth function of () without discontinuities and is less than 0.05% for all values of (). The total maximum variation in Ao[1 + A()] is therefore 0.25%. = VIN 86.63k + R' *For RH3-RL3: VOUTL-L Because the amplitude factor (RH - RL)Ao(1 + A()) varies simultaneously on all output lines, it will not be a source of error when the DR-11525 is to drive a ratiometric system such as a synchro or resolver. However, if the outputs are used independently, as in x-y plotters, the amplitude variations must be taken into account. 45.38k = VIN 49.92k + R' *Note: For RH2, RL2 and RH3, RL3: VOUT(single-ended) = 1/2 VOUTL-L. OUTPUT PHASING AND OUTPUT SCALE FACTOR PIN 1 2 3 4 5 6 7 8 9 10 11 12 The analog output signals have the following phasing: Resolver output: S3--S1 = (RH - RL)Ao(1 + A()) sin S2--S4 = (RH - RL)Ao(1 + A()) cos The output amplifiers simultaneously track reference voltage fluctuations because they are proportional to (RH - RL). The transformation ratio Ao is 11.8/26 for 11.8 VrmsL-L output. The maximum variation in Ao from all causes is 0.2%. The term A() represents the variation of the amplitude with the digital signal input angle. A(), which is called the scale factor variation, is a REFERENCE INPUTS 36.71k 49.92k 13.37k 36.71k 49.92k _ V (RH-RL) + NAME Bit 1 (MSB) Bit 15 Bit 16 (LSB) LM LL LA S4 (-COS) S1 (-SIN) NC NC S3 (+SIN) S2 (+COS) Notes: 1. -R (Pin 7) can be used for test purposes to detect whether a reference signal is present. See block diagram. 2. Functions LL, LA, and LM may be left unconnected when not used. 3. External scaling resistor pin 11 RH3 output pins (31, 32, 35, 36). 4. RH and RL (pins 10, 8) 26 V reference with differential outputs on pins 35, 36, 32, 31. 5. RH2 and RL2 (pins 5, 6) 26 V reference with single-ended output on pins 35, 36. 6. RH3 and RL3 (pins 11, 9) 4.4 V reference with single-ended outputs on pins 35, 36. 45.38k 13.37k TABLE 2. PIN CONNECTION TABLE NAME PIN NAME PIN NC 13 Bit 13 25 +15V 14 Bit 12 26 GND 15 Bit 11 27 -15V 16 Bit 10 28 RH2 (6.81V) 17 Bit 9 29 RL2 (6.81V) 18 Bit 8 30 -R 19 Bit 7 31 RL (11.8V) 20 Bit 6 32 21 Bit 5 33 RL3 (2V) 22 Bit 4 34 RH (11.8V) 23 Bit 3 35 RH3 (2V) 24 Bit 2 36 Bit 14 VOUT L-L 8.703k V (RH2-RL2) R V (RH3-RL3) R FIGURE 3. REFERENCE LEVEL ADJUSTMENT DR-11525 S3 35 S1 32 S3 S2 36 S4 31 S2 S3 35 (+SIN) S3 (+COS) S2 S1 DR-11525 S4 S2 36 GND 3 FIGURE 5. SINGLE-ENDED RESOLVER OUTPUT FIGURE 4. DIFFERENTIAL RESOLVER OUTPUT 3 ORDERING INFORMATION PIN NUMBERS FOR REFERENCE ONLY 1.900 MAX (48.26) 1 0.800 MAX (20.32) DR-11525D X-X X X Accuracy: 3 = 4 minutes 4 = 2 minutes 5 = 1 minute* Reliability: 0 = Standard DDC procedures 1 = Fully Compliant with MIL-PRF-38534 2 = Screened to MIL-PRF-38534 but without QCI testing 3 = Fully Compliant with MIL-PRF-38534 + PIND Testing 4 = Fully Compliant with MIL-PRF-38534 + Solder Dip 5 = Fully Compliant with MIL-PRF-38534 + PIND Testing + Solder Dip 6 = Screened to MIL-PRF-38534 + PIND Testing but without QCI Testing 7 = Screened to MIL-PRF-38534 + Solder Dip but without QCI Testing 8 = Screened to MIL-PRF-38534 + PIND Testing + Solder Dip but without QCI Testing Operating Temperature Range: 1 = -55 to +125C (Case) 3 = 0 to +70C (Case) 4 = -55 to +125C (Case) + Variables Data 8 = 0 to +70C (Case) + Variables Data Options: X = NONE Package: D = DIP Package 18 0.600 (15.24) BOTTOM VIEW 36 19 0.210 MAX (5.33) 0.010 TYP (0.25) SIDE VIEW 0.250 MIN (6.35) 0.018 0.002 DIA TYP (0.46 0.05) 0.100 TYP (2.54) 17 EQ. SP. @ 0.100 = 1.700 TOL NONCUM (@ 2.54 = 43.18) Notes: 1. Dimensions shown are in inches (millimeters). 2. Lead identification numbers are for referenced only. 3. Lead cluster shall be centered within 0.005 of outline dimensions. Lead spacing dimensions apply only at seating plane. 4. Pin material meets solderability requirements of MIL-STD-202E, Method 208C. FIGURE 6. DR-11525 MECHANICAL OUTLINE 36 PIN DDIP (CERAMIC) * Consult factory for availability of 1 minute parts. The information provided in this data sheet is believed to be accurate; however, no responsibility is assumed by Data Device Corporation for its use, and no license or rights are granted by implication or otherwise in connection therewith. Specifications are subject to change without notice. 105 Wilbur Place, Bohemia, New York 11716-2482 For Technical Support - 1-800-DDC-5757 ext. 7389 or 7413 Headquarters - Tel: (631) 567-5600 ext. 7389 or 7413, Fax: (631) 567-7358 Southeast - Tel: (703) 450-7900, Fax: (703) 450-6610 West Coast - Tel: (714) 895-9777, Fax: (714) 895-4988 Europe - Tel: +44-(0)1635-811140, Fax: +44-(0)1635-32264 Asia/Pacific - Tel: +81-(0)3-3814-7688, Fax: +81-(0)3-3814-7689 World Wide Web - http://www.ddc-web.com ILC DATA DEVICE CORPORATION REGISTERED TO ISO 9001 FILE NO. A5976 A-09/96-2M PRINTED IN THE U.S.A. 4