MCR01ZZPFL2R20 - ROHM Co., Ltd.

MCR01

Resistors

Rev.B 1/4

Low Ohmic Thick Film Chip Resistors

MCR01 (1005 size (0402 size) : 1 / 16W)

zFeatures

1) Power ra ting of 1 / 16W

2) Highly relia ble chip resistor

Ruthenium oxide dielectric offers superior resistance to the elements.

3) Electrodes not corroded by soldering

Thick film makes the electrodes very strong.

4) ROHM resistors have approved ISO9001- / ISO/TS16949- certification.

Design and specifications are subject to change without notice.

Carefully check the specification sheet before using or ordering it.

zRatings

0.063W (1 / 16W)

−55°

C to

+ 155°

at 70°C

Item Conditions Specifications

Rated power

Rated voltage

Operating temperature

Nominal resistance

See Table 1.

Limiting element voltage 0.75V(9.1Ω)

100

−55 0 70 100 155

AMBIENT TEMPERATURE (°C)

POWER LOAD (%)

Fig.1

The voltage rating is calculated by the following equation.

If the value obtained exceeds the limiting element voltage,

the voltage rating is equal to the maximum operating voltage.

E: Rated voltage (V)

P: Rated power (W)

R: Nominal resistance (Ω)

E= P×R

Power must be derated according to the power derating curve in

Figure 1 when ambient temperature exceeds 70°

MCR01

Resistors

Rev.B 2/4

F(±1%)

1.0≤ R ≤ 9.1 (E24) ±400

Table 1

Resistance tolerance Resistance range

(Ω)

Special

specification

Resistance temperature coefficient

(ppm/°C)

zBefore using components in circuit s where they will be exposed to transients such as pulse loads (short–dura tion, high– level loads), be certain to ev aluate the

component in the mounted state. In additio n, the reliability and performance of this component cannot be guaranteed if it is used with a steady st ate voltage that

is greater than its rated voltage.

zCharacteristics

Item Test conditions (JIS C 5201-1)

Resistor type

Guaranteed value

Resistance

Variation of resistance

with temperature

Solderability

Damp heat, steady state

Endurance at 70°C

Endurance

Rapid change of

temperature

Bend strength of

the end face plating

Resistance to solvent

Resistance to

soldering heat

Overload ± (2.0%+0.005Ω)

± (1.0%+0.005Ω)

± (3.0%+0.005Ω)

F : ±1%

See Table.1

No remarkable abnormality on the appearance.

A new uniform coating of minimum of

95% of the surface being immersed

and no soldering damage.

Without mechanical damage such as breaks.

JIS C 5201-1 4.5

JIS C 5201-1 4.8

Measurement : +25 / −55 / +25 / +125°C

Load voltage : A

Measuring method : measure upper termination

by 4 proves.

JIS C 5201-1 4.18

Soldering condition : 260±5

°C

Duration of immersion : 10±1s.

JIS C 5201-1 4.24

°C, 93%RH

Test time : 56days

± (3.0%+0.005Ω)

± (0.5%+0.005Ω)

± (1.0%+0.005Ω)

JIS C 5201-1 4.25.1

°C,

Rated voltage

1.5h : ON − 0.5h : OFF

Test time : 1,000h

JIS C 5201-1 4.25.3

155

°C

Test time : 1,000h to 1,048h

JIS C 5201-1 4.29

°C

±5

°C

, Immersion cleaning, 5±0.5min.

Solvent : 2-propanol

JIS C 5201-1 4.19

Test temp. : −55

°C

to +125

°C

5cyc

JIS C 5201-1 4.33

JIS C 5201-1 4.17

Rosin-Ethanol (25%WT)

Soldering condition : 235±5

°C

Duration of immersion : 2.0±0.5s.

JIS C 5201-1 4.13

Rated voltage (current) ×2.5, 2s.

Upper termination Prove

MCR01

Resistors

Rev.B 3/4

zDimensions (Unit : mm)

No. Material

Resistive element (Oxide metal thick film)

Silver thick film electrode

Nickel electrode

Sn electrode

Alumina substrate

Overcoating (Glass)

0.2±0.1

0.5±0.05 0.35±0.05

0.25+0.05

−0.1

1.0±0.05

zPackaging

0 2

0 4

0 6

0 8

0 2

0 4

0 6

0 8

ABD

ABCD

φ13±0.2

φD

Label

Reel Taping

EIAJ ET-7200B compliant

Thick paper

mount

(Underside paper tape)

Chip resistor Square punchout hole

Heat crimp cover tape

φ180 0

−1.5 φ60 +1

013 +1.0

φ1.5 +0.1

(Unit: mm)

WFEA

8.0±0.3 3.5±0.05 1.75±0.1 0.7±0.1 1.2±0.1

4.0±0.1 2.0±0.05 2.0±0.05 Max. 1.1

MCR01

Resistors

Rev.B 4/4

zPart No. Explanation

Special part number

Part No.

MC 0R

Nominal resistance

MZP 10,000

Paper tape (2mm Pitch) φ180mm (7inch)

1 M Z P F L

Resistance tolerance

1%F L Less than 10Ω (class F)

MCR01 ZZP 20,000

Paper tape (1mm Pitch) φ180mm (7inch)

MCR01

Packaging Specifications Code

Reel (φ180mm) : Compatible with JEITA standard "EIAJ ET-7200B"

: Standard product

Part No. Resistance tolerance

Code Packaging specifications Reel

Basic ordering unit(pcs)

1%)

FL : 4 digits

Resistance code, 4 digits.

Resistance

tolerance

+Special P/N Resistance

code

Notes

No technical content pages of this document may be reproduced in any form or transmitted by any

means without prior permission of ROHM CO.,LTD.

The contents described herein are subject to change without notice. The specifications for the

product described in this document are for reference only. Upon actual use, therefore, please request

that specifications to be separately delivered.

Application circuit diagrams and circuit constants contained herein are shown as examples of standard

use and operation. Please pay careful attention to the peripheral conditions when designing circuits

and deciding upon circuit constants in the set.

Any data, including, but not limited to application circuit diagrams information, described herein

are intended only as illustrations of such devices and not as the specifications for such devices. ROHM

CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any

third party's intellectual property rights or other proprietary rights, and further, assumes no liability of

whatsoever nature in the event of any such infringement, or arising from or connected with or related

to the use of such devices.

Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or

otherwise dispose of the same, no express or implied right or license to practice or commercially

exploit any intellectual property rights or other proprietary rights owned or controlled by

ROHM CO., LTD. is granted to any such buyer.

Products listed in this document are no antiradiation design.

Appendix1-Rev2.0

Thank you for your accessing to ROHM product informations.

More detail product informations and catalogs are available, please contact your nearest sales office.

ROHM Customer Support System THE AMERICAS / EUROPE / ASIA / JAPAN

www.rohm.com

The products listed in this document are designed to be used with ordinary electronic equipment or devices

(such as audio visual equipment, office-automation equipment, communications devices, electrical

appliances and electronic toys).

Should you intend to use these products with equipment or devices which require an extremely high level

of reliability and the malfunction of which would directly endanger human life (such as medical

instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers

and other safety devices), please be sure to consult with our sales representative in advance.

It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance

of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow

for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in

order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM

cannot be held responsible for any damages arising from the use of the products under conditions out of the

range of the specifications or due to non-compliance with the NOTES specified in this catalog.

21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan TEL : +81-75-311-2121

FAX : +81-75-315-0172

Appendix