GLS85LP0512P / 1002P / 1004P / 1008P Industrial Grade PATA NANDriveTM Fact Sheet 03.000 February 2014 Features Industry Standard ATA / IDE Bus Interface - Host Interface: 16-bit access - Supports 48-bit address feature set 1) - Supports up to PIO Mode-6 2) - Supports up to Multi-Word DMA Mode-4 - Supports up to Ultra DMA Mode-6 Performance - Sequential data read: Up to 50 MByte/sec - Sequential data write: Up to 35 MByte/sec Power Management - 3.3V power supply - Immediate disabling of unused circuitry without host intervention - Zero wake-up latency Power Specification - Active mode 100mA typical (GLS85LP1008P) 80mA typical (GLS85LP1004P) 60mA typical (GLS85LP1002P/0512P) - Sleep mode 500A typical Supports SMART Commands Expanded Data Protection - WP#/PD# pin configurable by firmware for prevention of data overwrites - Data security through user-selectable protection zones - Security Erase feature Integrated Voltage Detector - Prevents inadvertent Write operations due to unexpected power-down or brownout 20-Byte Unique ID for Enhanced Security - Factory pre-programmed 10-Byte unique ID - User-programmable 10-Byte ID Robust Built-in ECC NAND Configuration - 1 bit per cell (SLC) Temperature Range - Industrial: -40C to 85C 91-ball BGA and LBGA Packages - 14mm x 24mm x 1.90mm, 1mm ball pitch, FTE (2GB, 4GB, 8GB) - 12mm x 24mm x 1.40mm, 1mm ball pitch, LBTE (512MB) All Devices are RoHS Compliant Product Description The GLS85LP0512P / 1002P / 1004P / 1008P Industrial Grade PATA NANDriveTM devices (referred to as "PATA NANDrive" in this fact sheet) are highperformance, fully integrated solid state drives. They combine a Greenliant NAND controller and 512 MByte, 2 GByte, 4 GByte or 8 GByte of NAND flash memory in a multi-chip package. These products are ideal for embedded and portable applications that require smaller form factor and more reliable data storage. The integrated NAND flash controller with built-in advanced NAND management firmware communicates with the host through the standard ATA protocol. It does not require any additional or proprietary software such as the Flash File System (FFS) and Memory Technology Driver (MTD). PATA NANDrive provides a WP#/PD# pin to protect critical information stored in the flash media from unauthorized overwrites. PATA NANDrive is preprogrammed with a 10-Byte unique serial ID and has the option of programming an additional 10-Byte serial ID for even greater system security. PATA NANDrive's advanced NAND management technology enhances data security, improves endurance and accurately predicts the remaining lifespan of the NAND flash devices. This innovative technology combines robust error correction capabilities with advanced wear-leveling algorithms and bad block management to significantly extend the life of the product. ATA-based solid state mass storage technology is widely used in GPS and telematics, in-vehicle infotainment, portable and industrial computers, handheld data collection scanners, point-of-sale terminals, networking and telecommunications equipment, robotics, audio and video recorders, monitoring devices and set-top boxes. PATA NANDrive supports standard ATA/IDE protocol 1) 2) with up to PIO Mode-6 , Multi-Word DMA Mode-4 and Ultra DMA Mode-6 interface. The PATA NANDrive device provides complete IDE hard disk drive functionality and compatibility in a 14mm x 24mm BGA package or a 12mm x 24mm LBGA package for easy, space saving mounting to a system motherboard. These products surpass traditional storage in their small size, security, reliability, ruggedness and low power consumption. These specifications are subject to change without notice. (c) 2014 Greenliant Systems 1) 2) 1 PATA NANDrive is capable of supporting PIO Mode-6, but Identify-Drive information report will show PIO Mode-4 PATA NANDrive is capable of supporting Multi-Word DMA Mode-4, but Identify-Drive information report will show MWDMA Mode-2 02/19/2014 S71431-F GLS85LP0512P / 1002P / 1004P / 1008P Industrial Grade PATA NANDriveTM Fact Sheet 03.000 February 2014 1.0 GENERAL DESCRIPTION Each PATA NANDrive contains an integrated PATA NAND flash memory controller and NAND flash die in a BGA or LBGA package. Refer to Figure 2-1 for the PATA NANDrive block diagram. 1.1 Optimized PATA NANDrive 1.1.5 Error Correction Code (ECC) High performance is achieved through optimized hardware error detection and correction. The heart of PATA NANDrive is the PATA NAND flash memory controller, which translates standard PATA signals into flash media data and control signals. The following components contribute to PATA NANDrive's operation. 1.1.6 Serial Communication Interface (SCI) The Serial Communication Interface (SCI) is designed for error reporting. During the product development stage, it is recommended to provide the SCI port on the PCB to aid in design validation. 1.1.1 Microcontroller Unit (MCU) The MCU transfers the ATA/IDE commands into data and control signals required for flash media operation. 1.1.2 Internal Direct Memory Access (DMA) PATA NANDrive uses internal DMA allowing instant data transfer from/to buffer to/from flash media. This implementation eliminates microcontroller overhead associated with the traditional, firmware-based approach, thereby increasing the data transfer rate. 1.1.7 Multi-tasking Interface The multi-tasking interface enables fast, sustained write performance by allowing concurrent Read, Program and Erase operations to multiple flash media. 1.1.3 Power Management Unit (PMU) The PMU controls the power consumption of PATA NANDrive. The PMU dramatically reduces the power consumption of PATA NANDrive by putting the part of the circuitry that is not in operation into sleep mode. The PATA NANDrive family utilizes standard NAND flash for data storage. Because the high temperature in a surface-mount soldering reflow process can alter the content on NAND flash, do not program PATA NANDrive before the reflow process. 1.2 1.3 The Flash File System handles inadvertent power interrupts and has auto-recovery capability to ensure PATA NANDrive's data integrity. For regular power management, the host must send an IDLE_IMMEDIATE command and wait for command ready before powering down PATA NANDrive. SMT Reflow Consideration Advanced NAND Management PATA NANDrive's integrated controller uses advanced wear-leveling algorithms to substantially increase the longevity of NAND flash media. Wear caused by data writes is evenly distributed in all or select blocks in the device that prevents "hot spots" in locations that are programmed and erased extensively. This effective wear-leveling technique results in optimized device endurance, enhanced data retention and higher reliability required by long-life applications. 1.1.4 Embedded Flash File System The embedded flash file system is an integral part of PATA NANDrive. It contains MCU firmware that performs the following tasks: 1. Translates host side signals into flash media writes and reads 2. Provides flash media wear leveling to spread the flash writes across all memory address space to increase the longevity of flash media 3. Keeps track of data file structures 4. Manages system security for the selected protection zones 5. Stores the data in flash media upon completion of a Write command (PATA NANDrive does not perform Post-Write operations, except for when the write cache is enabled) These specifications are subject to change without notice. (c) 2014 Greenliant Systems 2 02/19/2014 S71431-F GLS85LP0512P / 1002P / 1004P / 1008P Industrial Grade PATA NANDriveTM Fact Sheet 03.000 February 2014 2.0 FUNCTIONAL BLOCKS Figure 2-1: PATA NANDrive Block Diagram These specifications are subject to change without notice. (c) 2014 Greenliant Systems 3 02/19/2014 S71431-F GLS85LP0512P / 1002P / 1004P / 1008P Industrial Grade PATA NANDriveTM Fact Sheet 03.000 February 2014 3.0 PRODUCT ORDERING INFORMATION GLS 85 LP 1 xxxP - S - I - FTE - NDxxx XX XX X XXXX - X - X - XXXX - XXXXX 3) Ordering Code NDxxx = NANDrive Revision EDxxx = Evaluation Board Revision Environmental Attribute E = non-Pb solder (RoHS Compliant) Package Modifier T = 88 ball positions (nearest letter code to total ball count of 91) Package Type F = BGA (max. package height 1.90mm) LB = LBGA (max. package height 1.40mm) Operation Temperature I = Industrial: -40C to +85C NAND configuration S = 1 bit per cell Generation / Product Configuration P = First generation Capacity 512 = 512 MByte 002 = 2 GByte 004 = 4 GByte 008 = 8 GByte MByte or GByte Designator 0 = MByte, 1 = GByte Interface P= Parallel ATA/IDE Interface Voltage L = 3.3V Product Series 85 = NANDrive 3) For legacy NANDrive products, no ordering code is required. Note that the top side marking on the package typically does not include ordering codes (e.g. NDxxx), unless it is a special C-SPEC (custom specification) which is required by the endcustomer to be marked on the device. These specifications are subject to change without notice. (c) 2014 Greenliant Systems 4 02/19/2014 S71431-F GLS85LP0512P / 1002P / 1004P / 1008P Industrial Grade PATA NANDriveTM Fact Sheet 03.000 February 2014 Valid Combinations Valid product combinations are those that are in the mass production or will be in the mass production. Consult your Greenliant sales representative to confirm availability of the valid combinations and to determine availability of new product combinations. Table 3-1: PATA NANDrive Product Valid Ordering Numbers Capacity Operating Temperature Part Number 512MB Industrial (-40C to 85C) GLS85LP0512P-S-I-LBTE GLS85LP1002P-S-I-FTE 2GB Industrial (-40C to 85C) GLS85LP1002P-S-I-FTE-ND001 GLS85LP1004P-S-I-FTE 4GB Industrial (-40C to 85C) GLS85LP1004P-S-I-FTE-ND001 GLS85LP1008P-S-I-FTE 8GB Industrial (-40C to 85C) GLS85LP1008P-S-I-FTE-ND001 Package LBTE, 12x24x1.40mm FTE, 14x24x1.90mm FTE, 14x24x1.90mm FTE, 14x24x1.90mm FTE, 14x24x1.90mm FTE, 14x24x1.90mm FTE, 14x24x1.90mm Table 3-2: PATA NANDrive Evaluation Board Valid Ordering Numbers Capacity Operating Temperature Part Number GLS85LP0512P-S-I-40CN-K 512MB Industrial (-40C to 85C) GLS85LP0512P-S-I-44CN-K GLS85LP1002P-S-I-40CN-K 2GB Industrial (-40C to 85C) GLS85LP1002P-S-I-44CN-K GLS85LP1002P-S-I-40CN-ED001 GLS85LP1004P-S-I-40CN-K 4GB Industrial (-40C to 85C) GLS85LP1004P-S-I-44CN-K GLS85LP1004P-S-I-40CN-ED001 GLS85LP1008P-S-I-40CN-K 8GB Industrial (-40C to 85C) GLS85LP1008P-S-I-44CN-K GLS85LP1008P-S-I-40CN-ED001 Form Factor Module with 40-pin ATA connector Module with 44-pin ATA connector Module with 40-pin ATA connector Module with 44-pin ATA connector Module with 40-pin ATA connector Module with 40-pin ATA connector Module with 44-pin ATA connector Module with 40-pin ATA connector Module with 40-pin ATA connector Module with 44-pin ATA connector Module with 40-pin ATA connector These specifications are subject to change without notice. (c) 2014 Greenliant Systems 5 02/19/2014 S71431-F GLS85LP0512P / 1002P / 1004P / 1008P Industrial Grade PATA NANDriveTM Fact Sheet 03.000 February 2014 3.1 Package Diagrams 3.1.1 FTE Package Figure 3-1: PATA NANDrive 91-Ball, Ball Grid Array (BGA) Greenliant Package Code: FTE Note: All linear dimensions are in millimeters. Un-tolerance dimensions are nominal target values. Co-planarity: 0.15 mm. Ball opening size is 0.40 mm ( 0.05 mm). These specifications are subject to change without notice. (c) 2014 Greenliant Systems 6 02/19/2014 S71431-F GLS85LP0512P / 1002P / 1004P / 1008P Industrial Grade PATA NANDriveTM Fact Sheet 03.000 February 2014 3.1.2 LBTE Package Figure 3-2: PATA NANDrive 91-Ball, Ball Grid Array (LBGA) Greenliant Package Code: LBTE Note: All linear dimensions are in millimeters. Un-tolerance dimensions are nominal target values. Co-planarity: 0.15 mm. Ball opening size is 0.40 mm ( 0.05 mm). These specifications are subject to change without notice. (c) 2014 Greenliant Systems 7 02/19/2014 S71431-F GLS85LP0512P / 1002P / 1004P / 1008P Industrial Grade PATA NANDriveTM Fact Sheet 03.000 February 2014 Revision History Revision 01.000 02.000 03.000 Description Initial release of datasheet Added Total program/erase cycle count Updated Power specification, Initialization time and Purge time Updated first page and Section 1.0; Removed Pin Assignments and Updated section numbering; Placed Valid Combinations into table format and Updated Section 3.0 Date June 15, 2011 June 1, 2012 February 19, 2014 (c) 2014 Greenliant Systems. All rights reserved. Greenliant and the Greenliant logo are registered trademarks, and NANDrive is a trademark of Greenliant Systems. All other trademarks and registered trademarks are the property of their respective owners. Specifications are subject to change without notice. Memory sizes denote raw storage capacity; actual usable capacity may be less. Greenliant makes no warranty for the use of its products other than those expressly contained in the Greenliant Terms and Conditions of Sale. www.greenliant.com These specifications are subject to change without notice. (c) 2014 Greenliant Systems 8 02/19/2014 S71431-F Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Greenliant: GLS85LP1002P-S-I-40CN-K GLS85LP1004P-S-I-44CN-K GLS85LP1008P-S-I-40CN-K GLS85LP1008P-S-I-44CN-K GLS85LP1002P-S-I-44CN-K GLS85LP1004P-S-I-40CN-K GLS85LP1008P-S-I-FTE-ND001 GLS85LP1004P-S-I-FTE GLS85LP1002P-S-I-FTE-ND001 GLS85LP1004P-S-I-FTE-ND001 GLS85LP1004B-M-I-FTE-ND000