GLS85LP1002P-S-I-44CN-K - Greenliant

Fact Sheet 03.000

February 2014

These specifications are subject to change without notice. 02/19/2014

GLS85LP0512P / 1002P / 1004P / 1008P

Industrial Grade PATA NANDrive™

Features

 Industry Standard ATA / IDE Bus Interface

- Host Interface: 16-bit access

- Supports 48-bit address feature set

- Supports up to PIO Mode-6 1)

- Supports up to Multi-Word DMA Mode-4 2)

- Supports up to Ultra DMA Mode-6

 Performance

- Sequential data read:

Up to 50 MByte/sec

- Sequential data write:

Up to 35 MByte/sec

 Power Management

- 3.3V power supply

- Immediate disabling of unused circuitry without

host intervention

- Zero wake-up latency

 Power Specification

- Active mode

100mA typical (GLS85LP1008P)

80mA typical (GLS85LP1004P)

60mA typical (GLS85LP1002P/0512P)

- Sleep mode

500µA typical

 Supports SMART Commands

 Expanded Data Protection

- WP#/PD# pin configurable by firmware for

prevention of data overwrites

- Data security through user-selectable protection

zones

- Security Erase feature

 Integrated Voltage Detector

- Prevents inadvertent Write operations due to

unexpected power-down or brownout

 20-Byte Unique ID for Enhanced Security

- Factory pre-programmed 10-Byte unique ID

- User-programmable 10-Byte ID

 Robust Built-in ECC

 NAND Configuration

- 1 bit per cell (SLC)

 Temperature Range

- Industrial: -40°C to 85°C

 91-ball BGA and LBGA Packages

- 14mm x 24mm x 1.90mm, 1mm ball pitch, FTE

(2GB, 4GB, 8GB)

- 12mm x 24mm x 1.40mm, 1mm ball pitch, LBTE

(512MB)

 All Devices are RoHS Compliant

Product Description

The GLS85LP0512P / 1002P / 1004P / 1008P

Industrial Grade PATA NANDrive™ devices (referred

to as “PATA NANDrive” in this fact sheet) are high-

performance, fully integrated solid state drives. They

combine a Greenliant NAND controller and 512 MByte,

2 GByte, 4 GByte or 8 GByte of NAND flash memory

in a multi-chip package. These products are ideal for

embedded and portable applications that require

smaller form factor and more reliable data storage.

ATA-based solid state mass storage technology is

widely used in GPS and telematics, in-vehicle

infotainment, portable and industrial computers,

handheld data collection scanners, point-of-sale

terminals, networking and telecommunications

equipment, robotics, audio and video recorders,

monitoring devices and set-top boxes.

PATA NANDrive supports standard ATA/IDE protocol

with up to PIO Mode-61), Multi-Word DMA Mode-42)

and Ultra DMA Mode-6 interface. The PATA

NANDrive device provides complete IDE hard disk

drive functionality and compatibility in a 14mm x

24mm BGA package or a 12mm x 24mm LBGA

package for easy, space saving mounting to a system

motherboard. These products surpass traditional

storage in their small size, security, reliability,

ruggedness and low power consumption.

The integrated NAND flash controller with built-in

advanced NAND management firmware

communicates with the host through the standard ATA

protocol. It does not require any additional or

proprietary software such as the Flash File System

(FFS) and Memory Technology Driver (MTD).

PATA NANDrive provides a WP#/PD# pin to protect

critical information stored in the flash media from

unauthorized overwrites. PATA NANDrive is pre-

programmed with a 10-Byte unique serial ID and has

the option of programming an additional 10-Byte serial

ID for even greater system security.

PATA NANDrive’s advanced NAND management

technology enhances data security, improves

endurance and accurately predicts the remaining

lifespan of the NAND flash devices. This innovative

technology combines robust error correction

capabilities with advanced wear-leveling algorithms

and bad block management to significantly extend the

life of the product.

1) PATA NANDrive is capable of supporting PIO Mode-6,

but Identify-Drive information report will show PIO Mode-4

2) PATA NANDrive is capable of supporting Multi-Word

DMA Mode-4, but Identify-Drive information report will

show MWDMA Mode-2

Fact Sheet 03.000

February 2014

These specifications are subject to change without notice. 02/19/2014

GLS85LP0512P / 1002P / 1004P / 1008P

Industrial Grade PATA NANDrive™

1.0 GENERAL DESCRIPTION

Each PATA NANDrive contains an integrated PATA NAND flash memory controller and NAND flash die in a BGA

or LBGA package. Refer to Figure 2-1 for the PATA NANDrive block diagram.

1.1 Optimized PATA NANDrive

The heart of PATA NANDrive is the PATA NAND flash

memory controller, which translates standard PATA

signals into flash media data and control signals. The

following components contribute to PATA NANDrive’s

operation.

1.1.1 Microcontroller Unit (MCU)

The MCU transfers the ATA/IDE commands into data

and control signals required for flash media operation.

1.1.2 Internal Direct Memory Access (DMA)

PATA NANDrive uses internal DMA allowing instant

data transfer from/to buffer to/from flash media. This

implementation eliminates microcontroller overhead

associated with the traditional, firmware-based

approach, thereby increasing the data transfer rate.

1.1.3 Power Management Unit (PMU)

The PMU controls the power consumption of PATA

NANDrive. The PMU dramatically reduces the power

consumption of PATA NANDrive by putting the part of

the circuitry that is not in operation into sleep mode.

The Flash File System handles inadvertent power

interrupts and has auto-recovery capability to ensure

PATA NANDrive’s data integrity. For regular power

management, the host must send an

IDLE_IMMEDIATE command and wait for command

ready before powering down PATA NANDrive.

1.1.4 Embedded Flash File System

The embedded flash file system is an integral part of

PATA NANDrive. It contains MCU firmware that

performs the following tasks:

1. Translates host side signals into flash media

writes and reads

2. Provides flash media wear leveling to spread

the flash writes across all memory address

space to increase the longevity of flash media

3. Keeps track of data file structures

4. Manages system security for the selected

protection zones

5. Stores the data in flash media upon completion

of a Write command (PATA NANDrive does not

perform Post-Write operations, except for when

the write cache is enabled)

1.1.5 Error Correction Code (ECC)

High performance is achieved through optimized

hardware error detection and correction.

1.1.6 Serial Communication Interface (SCI)

The Serial Communication Interface (SCI) is designed

for error reporting. During the product development

stage, it is recommended to provide the SCI port on

the PCB to aid in design validation.

1.1.7 Multi-tasking Interface

The multi-tasking interface enables fast, sustained

write performance by allowing concurrent Read,

Program and Erase operations to multiple flash media.

1.2 SMT Reflow Consideration

The PATA NANDrive family utilizes standard NAND

flash for data storage. Because the high temperature

in a surface-mount soldering reflow process can alter

the content on NAND flash, do not program PATA

NANDrive before the reflow process.

1.3 Advanced NAND Management

PATA NANDrive’s integrated controller uses

advanced wear-leveling algorithms to substantially

increase the longevity of NAND flash media. Wear

caused by data writes is evenly distributed in all or

select blocks in the device that prevents “hot spots” in

locations that are programmed and erased extensively.

This effective wear-leveling technique results in

optimized device endurance, enhanced data retention

and higher reliability required by long-life applications.

Fact Sheet 03.000

February 2014

These specifications are subject to change without notice. 02/19/2014

GLS85LP0512P / 1002P / 1004P / 1008P

Industrial Grade PATA NANDrive™

2.0 FUNCTIONAL BLOCKS

Figure 2-1: PATA NANDrive Block Diagram

Fact Sheet 03.000

February 2014

These specifications are subject to change without notice. 02/19/2014

GLS85LP0512P / 1002P / 1004P / 1008P

Industrial Grade PATA NANDrive™

3.0 PRODUCT ORDERING INFORMATION

GLS 85 LP 1 xxxP - S - I - FTE - NDxxx

XX XX X XXXX - X - X - XXXX - XXXXX

Ordering Code 3)

NDxxx = NANDrive Revision

EDxxx = Evaluation Board Revision

Environmental Attribute

E = non-Pb solder (RoHS Compliant)

Package Modifier

T = 88 ball positions (nearest letter code

to total ball count of 91)

Package Type

F = BGA (max. package height 1.90mm)

LB = LBGA (max. package height 1.40mm)

Operation Temperature

I = Industrial: -40°C to +85°C

NAND configuration

S = 1 bit per cell

Generation / Product Configuration

P = First generation

Capacity

512 = 512 MByte

002 = 2 GByte

004 = 4 GByte

008 = 8 GByte

MByte or GByte Designator

0 = MByte, 1 = GByte

Interface

P= Parallel ATA/IDE Interface

Voltage

L = 3.3V

Product Series

85 = NANDrive

3) For legacy NANDrive products, no ordering code is required. Note that the top side marking on the package typically does

not include ordering codes (e.g. NDxxx), unless it is a special C-SPEC (custom specification) which is required by the end-

customer to be marked on the device.

Fact Sheet 03.000

February 2014

These specifications are subject to change without notice. 02/19/2014

GLS85LP0512P / 1002P / 1004P / 1008P

Industrial Grade PATA NANDrive™

Valid Combinations

Valid product combinations are those that are in the mass production or will be in the mass production. Consult

your Greenliant sales representative to confirm availability of the valid combinations and to determine availability

of new product combinations.

Table 3-1: PATA NANDrive Product Valid Ordering Numbers

Capacity

Operating Temperature

Part Number

Package

512MB

Industrial (-40°C to 85°C)

GLS85LP0512P-S-I-LBTE

LBTE, 12x24x1.40mm

2GB

Industrial (-40°C to 85°C)

GLS85LP1002P-S-I-FTE

FTE, 14x24x1.90mm

GLS85LP1002P-S-I-FTE-ND001

FTE, 14x24x1.90mm

4GB

Industrial (-40°C to 85°C)

GLS85LP1004P-S-I-FTE

FTE, 14x24x1.90mm

GLS85LP1004P-S-I-FTE-ND001

FTE, 14x24x1.90mm

8GB

Industrial (-40°C to 85°C)

GLS85LP1008P-S-I-FTE

FTE, 14x24x1.90mm

GLS85LP1008P-S-I-FTE-ND001

FTE, 14x24x1.90mm

Table 3-2: PATA NANDrive Evaluation Board Valid Ordering Numbers

Capacity

Operating Temperature

Part Number

Form Factor

512MB

Industrial (-40°C to 85°C)

GLS85LP0512P-S-I-40CN-K

Module with 40-pin ATA connector

GLS85LP0512P-S-I-44CN-K

Module with 44-pin ATA connector

2GB

Industrial (-40°C to 85°C)

GLS85LP1002P-S-I-40CN-K

Module with 40-pin ATA connector

GLS85LP1002P-S-I-44CN-K

Module with 44-pin ATA connector

GLS85LP1002P-S-I-40CN-ED001

Module with 40-pin ATA connector

4GB

Industrial (-40°C to 85°C)

GLS85LP1004P-S-I-40CN-K

Module with 40-pin ATA connector

GLS85LP1004P-S-I-44CN-K

Module with 44-pin ATA connector

GLS85LP1004P-S-I-40CN-ED001

Module with 40-pin ATA connector

8GB

Industrial (-40°C to 85°C)

GLS85LP1008P-S-I-40CN-K

Module with 40-pin ATA connector

GLS85LP1008P-S-I-44CN-K

Module with 44-pin ATA connector

GLS85LP1008P-S-I-40CN-ED001

Module with 40-pin ATA connector

Fact Sheet 03.000

February 2014

These specifications are subject to change without notice. 02/19/2014

GLS85LP0512P / 1002P / 1004P / 1008P

Industrial Grade PATA NANDrive™

3.1 Package Diagrams

3.1.1 FTE Package

Figure 3-1: PATA NANDrive 91-Ball, Ball Grid Array (BGA) Greenliant Package Code: FTE

Note: All linear dimensions are in millimeters.

Un-tolerance dimensions are nominal target values.

Co-planarity: 0.15 mm.

Ball opening size is 0.40 mm (± 0.05 mm).

Fact Sheet 03.000

February 2014

These specifications are subject to change without notice. 02/19/2014

GLS85LP0512P / 1002P / 1004P / 1008P

Industrial Grade PATA NANDrive™

3.1.2 LBTE Package

Figure 3-2: PATA NANDrive 91-Ball, Ball Grid Array (LBGA) Greenliant Package Code: LBTE

Note: All linear dimensions are in millimeters.

Un-tolerance dimensions are nominal target values.

Co-planarity: 0.15 mm.

Ball opening size is 0.40 mm (± 0.05 mm).

Fact Sheet 03.000

February 2014

These specifications are subject to change without notice. 02/19/2014

GLS85LP0512P / 1002P / 1004P / 1008P

Industrial Grade PATA NANDrive™

Revision History

Revision

Description

Date

01.000

Initial release of datasheet

June 15, 2011

02.000

Added Total program/erase cycle count

Updated Power specification, Initialization time and Purge time

June 1, 2012

03.000

Updated first page and Section 1.0; Removed Pin Assignments and

Updated section numbering; Placed Valid Combinations into table

format and Updated Section 3.0

February 19, 2014

Greenliant and the Greenliant logo are registered trademarks, and NANDrive is a trademark of Greenliant

Systems. All other trademarks and registered trademarks are the property of their respective owners.

Specifications are subject to change without notice. Memory sizes denote raw storage capacity; actual usable

capacity may be less.

Greenliant makes no warranty for the use of its products other than those expressly contained in the Greenliant

Terms and Conditions of Sale.

www.greenliant.com

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Greenliant:

GLS85LP1002P-S-I-40CN-K GLS85LP1004P-S-I-44CN-K GLS85LP1008P-S-I-40CN-K GLS85LP1008P-S-I-44CN-K

GLS85LP1002P-S-I-44CN-K GLS85LP1004P-S-I-40CN-K GLS85LP1008P-S-I-FTE-ND001 GLS85LP1004P-S-I-FTE

GLS85LP1002P-S-I-FTE-ND001 GLS85LP1004P-S-I-FTE-ND001 GLS85LP1004B-M-I-FTE-ND000