SEMICONDUCTOR TECHNICAL DATA " ! High-Performance Silicon-Gate CMOS The MC54/74HC86A is identical in pinout to the LS86; this device is similar in function to the MM74C86 and L86, but has a different pinout. The device inputs are compatible with standard CMOS outputs; with pullup resistors, they are compatible with LSTTL outputs. * * * * * * Output Drive Capability: 10 LSTTL Loads Outputs Directly Interface to CMOS, NMOS, and TTL Operating Voltage Range: 2 to 6 V Low Input Current: 1 A High Noise Immunity Characteristic of CMOS Devices In Compliance with the Requirements Defined by JEDEC Standard No. 7A * Chip Complexity: 56 FETs or 14 Equivalent Gates J SUFFIX CERAMIC PACKAGE CASE 632-08 14 1 N SUFFIX PLASTIC PACKAGE CASE 646-06 14 1 1 D SUFFIX SOIC PACKAGE CASE 751A-03 1 DT SUFFIX TSSOP PACKAGE CASE 948G-01 14 14 LOGIC DIAGRAM ORDERING INFORMATION A1 B1 A2 B2 A3 B3 A4 B4 1 2 4 5 3 6 Y1 Y2 Y= AB 9 10 12 13 PIN ASSIGNMENT = AB + AB 8 11 Ceramic Plastic SOIC TSSOP MC54HCXXAJ MC74HCXXAN MC74HCXXAD MC74HCXXADT Y3 Y4 PIN 14 = VCC PIN 7 = GND A1 1 14 VCC B1 2 13 B4 Y1 3 12 A4 A2 4 11 Y4 B2 5 10 B3 Y2 6 9 A3 GND 7 8 Y3 FUNCTION TABLE Inputs 3/97 Motorola, Inc. 1997 1 REV 1 Output A B Y L L H H L H L H L H H L MC54/74HC86A IIIIIIIIIIIIIIIIIIIIIII III IIIIIIIIIIIIII IIIIII III IIIIIIIIIIIIIIIIIIIIIII III IIIIIIIIIIIIII IIIIII III III IIIIIIIIIIIIII IIIIII III III IIIIIIIIIIIIII IIIIII III III IIIIIIIIIIIIII IIIIII III III IIIIIIIIIIIIII IIIIII III III IIIIIIIIIIIIII IIIIII III III IIIIIIIIIIIIII IIIIII III III IIIIIIIIIIIIII IIIIII III III IIIIIIIIIIIIII IIIIII III III IIIIIIIIIIIIII IIIIII III III IIIIIIIIIIIIII IIIIII III III IIIIIIIIIIIIII IIIIII III III IIIIIIIIIIIIII IIIIII III MAXIMUM RATINGS* Symbol VCC Parameter DC Supply Voltage (Referenced to GND) Value Unit - 0.5 to + 7.0 V V Vin DC Input Voltage (Referenced to GND) - 0.5 to VCC + 0.5 Vout DC Output Voltage (Referenced to GND) - 0.5 to VCC + 0.5 V DC Input Current, per Pin 20 mA Iout DC Output Current, per Pin 25 mA ICC DC Supply Current, VCC and GND Pins 50 mA PD Power Dissipation in Still Air, Plastic or Ceramic DIP SOIC Package TSSOP Package 750 500 450 mW Tstg Storage Temperature - 65 to + 150 _C Iin TL This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, Vin and Vout should be constrained to the range GND (Vin or Vout) VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open. v v _C Lead Temperature, 1 mm from Case for 10 Seconds (Plastic DIP, SOIC or TSSOP Package) (Ceramic DIP) 260 300 * Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. Derating -- Plastic DIP: - 10 mW/_C from 65_ to 125_C Ceramic DIP: - 10 mW/_C from 100_ to 125_C SOIC Package: - 7 mW/_C from 65_ to 125_C TSSOP Package: - 6.1 mW/_C from 65_ to 125_C For high frequency or heavy load considerations, see Chapter 2 of the Motorola High-Speed CMOS Data Book (DL129/D). IIII IIIIIIIIIIIIII III III III IIII IIIIIIIIIIIIII III III III IIII IIIIIIIIIIIIII III III III IIII IIIIIIIIIIIIII III III III IIII IIIIIIIIIIIIII III III III IIII IIIIIIIIIIIIII III III III IIII IIIIIIIIIIIIII III III III IIII IIIIIIIII IIIIIIIII IIII IIIIIIIII III IIII IIIIIIIII IIIIIIIII IIII III IIII IIII III IIIIIIIII v IIII v III IIII IIIIIIIII IIIIIIIII IIII III IIII III IIII IIIIIIIII IIIIIIIII IIII IIII IIII III v IIII IIIIIIIII IIIIIIIII IIII III IIII IIII III III IIII IIIIIIIII IIIIIIIII IIII IIII IIII III III IIII IIIIIIIII IIIIIIIII IIII IIII IIII III v IIII IIIIIIIII IIIIIIIII IIII III IIII IIII III III IIII IIIIIIIII IIIIIIIII IIII IIII IIII III III IIII IIIIIIIII IIIIIIIII IIII IIII IIII III v IIII IIIIIIIII IIIIIIIII IIII III IIII IIII III III IIII IIIIIIIII IIIIIIIII IIII IIII III v IIII v IIII IIIIIIIII IIIIIIIII III IIII IIII III v IIII III IIII IIIIIIIII IIIIIIIII IIII IIII IIII III RECOMMENDED OPERATING CONDITIONS Symbol VCC Vin, Vout Parameter DC Supply Voltage (Referenced to GND) Min Max Unit 2.0 6.0 V 0 VCC V - 55 + 125 _C 0 0 0 1000 500 400 ns DC Input Voltage, Output Voltage (Referenced to GND) TA Operating Temperature, All Package Types tr, tf Input Rise and Fall Time (Figure 1) VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND) Guaranteed Limit S b l Symbol P Parameter T Test C Conditions di i VCC V - 55 to 25_C 85_C 125_C U i Unit VIH Minimum High-Level Input Voltage Vout = 0.1 V or VCC - 0.1 V |Iout| 20 A 2.0 3.0 4.5 6.0 1.5 2.1 3.15 4.2 1.5 2.1 3.15 4.2 1.5 2.1 3.15 4.2 V VIL Maximum Low-Level Input Voltage Vout = 0.1 V or VCC - 0.1 V |Iout| 20 A 2.0 3.0 4.5 6.0 0.5 0.9 1.35 1.8 0.5 0.9 1.35 1.8 0.5 0.9 1.35 1.8 V Minimum High-Level Output Voltage Vin = VIH or VIL |Iout| 20 A 2.0 4.5 6.0 1.9 4.4 5.9 1.9 4.4 5.9 1.9 4.4 5.9 V 3.0 4.5 6.0 2.48 3.98 5.48 2.34 3.84 5.34 2.20 3.70 5.20 VOH Vin = VIH or VIL |Iout| |Iout| |Iout| MOTOROLA 2 2.4 mA 4.0 mA 5.2 mA High-Speed CMOS Logic Data DL129 -- Rev 6 MC54/74HC86A IIII IIIIIIIII IIIIIIIII IIII IIIIIIIII III IIII IIIIIIIII IIIIIIIII IIII III IIII IIII III IIIIIIIII v IIII v III IIII IIIIIIIII IIIIIIIII IIII III IIII IIII IIIIIIIII IIIIIIIII IIII III IIII IIII III v IIII IIIIIIIII IIIIIIIII IIII III IIII IIII III III IIII IIIIIIIII IIIIIIIII IIII IIII III v IIII v IIII IIII IIIIIIIII IIIIIIIII III IIII IIII III v III IIII IIIIIIIII IIIIIIIII IIII IIII IIII III IIII IIIIIIIII IIIIIIIII IIII III IIII IIII III IIII IIIIIIIII IIIIIIIII IIII III IIII IIII III IIII IIIIIIIII IIIIIIIII IIIIIII IIII IIII III DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND) Guaranteed Limit Symbol VOL Parameter Test Conditions Maximum Low-Level Output Voltage Vin = VIH or VIL |Iout| 20 A Vin = VIH or VIL |Iout| |Iout| |Iout| Iin ICC 2.4 mA 4.0 mA 5.2 mA VCC V - 55 to 25_C 85_C 125_C 2.0 4.5 6.0 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 3.0 4.5 6.0 0.26 0.26 0.26 0.33 0.33 0.33 0.40 0.40 0.40 Unit V Maximum Input Leakage Current Vin = VCC or GND 6.0 0.1 1.0 1.0 A Maximum Quiescent Supply Current (per Package) Vin = VCC or GND Iout = 0 A 6.0 1.0 10 40 A NOTE: Information on typical parametric values can be found in Chapter 2 of the Motorola High-Speed CMOS Data Book (DL129/D). IIII IIIIIIIIIIIIIIIII IIII IIIIIIIII III IIII IIIIIIIIIIIIIIIII IIII III IIII IIIIIIIII v IIII v III IIII IIIIIIIIIIIIIIIII IIII III IIII IIII III IIII IIIIIIIIIIIIIIIII IIII III IIII IIII III III IIII IIIIIIIIIIIIIIIII IIII IIII IIII III III IIII IIIIIIIIIIIIIIIII IIII IIII IIII III IIII IIIIIIIIIIIIIIIII IIII III IIII IIII III III IIII IIIIIIIIIIIIIIIII IIII IIII IIII III III IIII IIIIIIIIIIIIIIIII IIII IIII IIII III IIII IIIIIIIIIIIIIIIII IIII III IIII IIII III AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input t, = tf = 6 ns) Guaranteed Limit S b l Symbol P Parameter VCC V - 55 to 25_C 85_C 125_C U i Unit tPLH, tPHL Maximum Propagation Delay, Input A or B to Output Y (Figures 1 and 2) 2.0 3.0 4.5 6.0 100 80 20 17 125 90 25 21 150 110 31 26 ns tTLH, tTHL Maximum Output Transition Time, Any Output (Figures 1 and 2) 2.0 3.0 4.5 6.0 75 30 15 13 95 40 19 16 110 55 22 19 ns Maximum Input Capacitance -- 10 10 10 pF Cin NOTES: 1. For propagation delays with loads other than 50 pF, see Chapter 2 of the Motorola High-Speed CMOS Data Book (DL129/D). 2. Information on typical parametric values can be found in Chapter 2 of the Motorola High-Speed CMOS Data Book (DL129/D). Typical @ 25C, VCC = 5.0 V CPD P Power Dissipation Di i i C Capacitance i (P (Per G Gate)* )* 33 pF F * Used to determine the no-load dynamic power consumption: P D = C PD V CC 2 f + I CC V CC . For load considerations, see Chapter 2 of the Motorola High-Speed CMOS Data Book (DL129/D). High-Speed CMOS Logic Data DL129 -- Rev 6 3 MOTOROLA MC54/74HC86A tr tf VCC 90% 50% INPUT A OR B TEST POINT 10% GND OUTPUT tPLH tPHL 90% OUTPUT Y DEVICE UNDER TEST CL* 50% 10% tTLH tTHL * Includes all probe and jig capacitance Figure 1. Switching Waveforms Figure 2. Test Circuit EXPANDED LOGIC DIAGRAM (1/4 of Device) A Y B MOTOROLA 4 High-Speed CMOS Logic Data DL129 -- Rev 6 MC54/74HC86A OUTLINE DIMENSIONS J SUFFIX CERAMIC DIP PACKAGE CASE 632-08 ISSUE Y -A14 8 1 7 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIMESNION F MAY NARROW TO 0.76 (0.030) WHERE THE LEAD ENTERS THE CERAMIC BODY. -B- C -T- L DIM A B C D F G J K L M N K SEATING PLANE F G D 14 PL 0.25 (0.010) M N T A M J 14 PL 0.25 (0.010) S M T B S N SUFFIX PLASTIC DIP PACKAGE CASE 646-06 ISSUE L 14 B 7 A F DIM A B C D F G H J K L M N L C J N H G D SEATING PLANE K M D SUFFIX PLASTIC SOIC PACKAGE CASE 751A-03 ISSUE F -A- 14 1 P 7 PL 0.25 (0.010) 7 G D 0.25 (0.010) High-Speed CMOS Logic Data DL129 -- Rev 6 M T F J M K 14 PL B S M R X 45 C SEATING PLANE B M A S 5 INCHES MIN MAX 0.715 0.770 0.240 0.260 0.145 0.185 0.015 0.021 0.040 0.070 0.100 BSC 0.052 0.095 0.008 0.015 0.115 0.135 0.300 BSC 0_ 10_ 0.015 0.039 MILLIMETERS MIN MAX 18.16 19.56 6.10 6.60 3.69 4.69 0.38 0.53 1.02 1.78 2.54 BSC 1.32 2.41 0.20 0.38 2.92 3.43 7.62 BSC 0_ 10_ 0.39 1.01 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 8 -B- MILLIMETERS MIN MAX 19.05 19.94 6.23 7.11 3.94 5.08 0.39 0.50 1.40 1.65 2.54 BSC 0.21 0.38 3.18 4.31 7.62 BSC 0 15 0.51 1.01 NOTES: 1. LEADS WITHIN 0.13 (0.005) RADIUS OF TRUE POSITION AT SEATING PLANE AT MAXIMUM MATERIAL CONDITION. 2. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 3. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 4. ROUNDED CORNERS OPTIONAL. 8 1 INCHES MIN MAX 0.750 0.785 0.245 0.280 0.155 0.200 0.015 0.020 0.055 0.065 0.100 BSC 0.008 0.015 0.125 0.170 0.300 BSC 0 15 0.020 0.040 DIM A B C D F G J K M P R MILLIMETERS MIN MAX 8.75 8.55 4.00 3.80 1.75 1.35 0.49 0.35 1.25 0.40 1.27 BSC 0.25 0.19 0.25 0.10 7 0 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.337 0.344 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 7 0 0.228 0.244 0.010 0.019 MOTOROLA MC54/74HC86A OUTLINE DIMENSIONS DT SUFFIX PLASTIC TSSOP PACKAGE CASE 948G-01 ISSUE O 14X K REF 0.10 (0.004) 0.15 (0.006) T U M T U V S NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. S S N 2X 14 L/2 0.25 (0.010) 8 M B -U- L PIN 1 IDENT. F 7 1 0.15 (0.006) T U N S DETAIL E CCC EEE CCC EEE CCC EEE K A -V- K1 J J1 SECTION N-N -W- C 0.10 (0.004) -T- SEATING PLANE D H G DETAIL E DIM A B C D F G H J J1 K K1 L M MILLIMETERS MIN MAX 4.90 5.10 4.30 4.50 --- 1.20 0.05 0.15 0.50 0.75 0.65 BSC 0.50 0.60 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0_ 8_ INCHES MIN MAX 0.193 0.200 0.169 0.177 --- 0.047 0.002 0.006 0.020 0.030 0.026 BSC 0.020 0.024 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0_ 8_ Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Mfax is a trademark of Motorola, Inc. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 303-675-2140 or 1-800-441-2447 JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 81-3-3521-8315 Mfax: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, - US & Canada ONLY 1-800-774-1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 INTERNET: http://www.mot.com/SPS/ MOTOROLA 6 MC74HC86A/D High-Speed CMOS Logic Data DL129 -- Rev 6