®
RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 1
RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com
©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. SF2037B-3-050807
Notes:
1. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to
50 Ω and measured with 50 Ω network analyzer.
2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc.
3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance
matching design. See Application Note No. 42 for details.
4. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes."
5. The design, manufacturing process, and specifications of this filter are subject to change.
6. Tape and Reel Standard ANSI / EIA 481.
7. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that
the filter must always be installed in one direction per the circuit design.
8. US and international patents may apply.
9. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc.
10. ©Copyright 1999, RF Monolithics Inc.
11. Electrostatic Sensitive Device. Observe precautions for handling.
Electrical Characteristics
Characteristic Sym Notes Min Typ Max Units
Nominal Center Frequency fC176.500 MHz
Passband Insertion Loss IL 10.0 12.0 dB
1dB Passband BW1
1
3.8 4.1 MHz
15dB Bandwidth BW15 6.7 6.8 MHz
30dB Bandwidth BW30 7.7 7.8 MHz
Amplitude Ripple over fc ±1.9 MHz 0.5 1.10 dBP-P
Group Delay Variation over fc ±1.9 MHz GDV 65 150 nsP-P
Rejection 50 to 65.44 MHz
1, 3
40 45
dB
65.44 to 70.44 MHz 39 43
70.44 to 72.04 MHz 36 43
81.26 to 82.56 MHz 38 49
82.56 to 86.50 MHz 39 48
86.5 to 91.50 MHz 41 48
91.50 to 100.000 MHz 45 58
Operating Temperature Range TA1-40 +85 °C
Frequency Temperture Coefficient FTC -18 ppm/°C
Differential Input 175 ohms
Differential Output 1000 ohms
Case Style 6SMP-03-S 7 x 5 mm Nominal Footprint
Lid Symbolization (YY=year, WW=week, S=shift) See note 4 RFM SF2037B-3 YYWWS
SMP-03-S
•Designed for SDARS IF Receiver
•Low Insertion Loss
•5.0 X 7.0 mm Surface-Mount Case
•Differential or Single Ended Input and Output
•Complies with Directive 2002/95/EC (RoHS)
Absolute Maximum Ratings
Rating Value Units
Maximum Incident Power in Passband +10 dBm
Max. DC voltage between any 2 terminals 30 VDC
Storage Temperature Range -40 to +85 °C
Max Soldering Profile 265°C for 10 s
76.500 MHz
SAW Filter
SF2037B-3
Pb
Connection Port 1 Hot Port 1 Ground Return or Hot Port 2 Hot Port 2 Ground Return or Hot Case Ground
Terminals 10 1 5 6 All Others
Electrical Connections
76.500 MHz SAW Filter
RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 2
RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com
©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. SF2037B-3-050807
SMP-03-S Case
12-Terminal Ceramic Surface-Mount Case
5 x 7 mm Nominal Footprint
Case Dimensions
Dimension mm Inches
Min Nom Max Min Nom Max
A6.80 7.00 7.20 0.268 0.276 0.283
B4.80 5.00 5.20 0.189 0.197 0.205
C1.65 2.00 0.065 0.079
D0.80
E2.41 2.54 2.67 0.095 0.100 0.105
H0.87 1.1 1.13 0.034 0.039 0.044
J2.54
K2.8
P1.14 1.27 1.40 0.045 0.050 0.055
Materials
Solder Pad
Termination Au plating 30 - 60 µinches (76.2-152 µm) over 80-
200 µinches (203-508 µm) Ni.
Lid Fe-Ni-Co Alloy Electroless Nickel Plate (8-11%
Phosphorus) 100-200 µinches Thick
Body Al2O3 Ceramic
Pb Free
Pb
76.500 MHz SAW Filter
RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 3
RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com
©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. SF2037B-3-050807
COVER TAPE SIZE
KO
COVER TAPE 0.32 mm ±0.3
2.15 mm ±0.2
W
(CARRIER TAPE SIZE)
AO
BO
P
(PITCH)
1.5 mm +0.1
-0.0
4.0 mm ±0.1
2.0 mm ±0.1
1.75 mm ±0.1
7.5 mm ±0.1
1.5 mm +0.3
-0.0
PIN #1
USER DIRECTION OF FEED
COMPONENTORIENTATIONandDIMENSIONS
Carrier Tape Dimensions
Ao 5.5 mm ±0.1
Bo 7.5 mm ±0.1
Ko 2.0 mm ±0.1
Pitch 8.0 mm ±0.1
W16.0 mm ±0.3
