Product Folder Sample & Buy Technical Documents Support & Community Tools & Software TPS3820-33-Q1, TPS3820-50-Q1, TPS3823-25-Q1 TPS3823-30-Q1, TPS3823-33-Q1, TPS3823-50-Q1, TPS3824-30-Q1, TPS3824-33-Q1 TPS3824-50-Q1, TPS3825-33-Q1, TPS3825-50-Q1, TPS3828-33-Q1, TPS3828-50-Q1 SGLS143C - DECEMBER 2002 - REVISED DECEMBER 2015 TPS382x-xx-Q1 Voltage Monitor With Watchdog Timer 1 Features 3 Description * * The TPS382x-xx-Q1 family of supervisors provide circuit initialization and timing supervision, primarily for DSP and processor-based systems. During power on, RESET asserts when the supply voltage VDD becomes greater than 1.1 V. Thereafter, the supply voltage supervisor monitors VDD and keeps RESET active low as long as VDD remains below the threshold voltage, VIT-. An internal timer delays the return of the output to the inactive state (high) to ensure proper system reset. The delay time, td, starts after VDD has risen above the threshold voltage VIT-. When the supply voltage drops below the threshold voltage VIT-, the output becomes active (low) again. No external components are required. All the devices of this family have a fixed-sense threshold voltage, VIT-, set by an internal voltage divider. The TPS382xxx-Q1 family also offers watchdog time out options of 200 ms (TPS3820-xx-Q1) and 1.6 s (TPS3823/4/8xx-Q1). 1 * * * * * * * * * Qualified for Automotive Applications AEC-Q100 Qualified With the Following Results: - Device Temperature Grade 1: -40C to 125C - Device HBM ESD Classification Level 2 - Device CDM ESD Classification Level C4B ESD Protection Exceeds 2000 V Per MIL-STD883, Method 3015; Using Human Body Model (C = 100 pF, R = 1500 ) Power-On Reset Generator With Fixed Delay Time of 200 ms (TPS3823/4/5/8-xx-Q1) or 25 ms (TPS3820-xx-Q1) Manual Reset Input (TPS3820/3/5/8-xx-Q1) Reset Output Available in Active-Low (TPS3820/3/4/5-xx-Q1), Active-High (TPS3824/5xx-Q1), and Open Drain (TPS3828-xx-Q1) Supply Voltage Supervision Range: 2.5 V, 3 V, 3.3 V, 5 V Watchdog Timer (TPS3820/3/4/8-xx-Q1) Supply Current of 15 A (Typical) 5-Pin SOT-23 Package Temperature Range: -40C to 125C Device Information(1) PART NUMBER TPS382x-xx-Q1 PACKAGE BODY SIZE (NOM) SOT-23 (5) 2.90 mm x 1.60 mm (1) For all available packages, see the orderable addendum at the end of the datasheet. 2 Applications * * * * * * Automotive DSPs, Microcontrollers, or Microprocessors Industrial Equipment Programmable Controls Automotive Systems Portable and Battery-Powered Equipment Intelligent Instruments Wireless Communications Systems Typical Application Schematic 3.3 V 100 nF VDD RESET VDD RESET TPS3823-33-Q1 WDI MR GND MSP430C325 I/O GND Normalized Input Threshold Voltage vs Free-Air Temperature Normalized Input Threshold Voltage -V IT (TA), VIT (25C) * 1.001 1 0.999 0.998 0.997 0.996 0.995 -40 -15 10 35 60 85 TA - Free-Air Temperature - C 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. TPS3820-33-Q1, TPS3820-50-Q1, TPS3823-25-Q1 TPS3823-30-Q1, TPS3823-33-Q1, TPS3823-50-Q1, TPS3824-30-Q1, TPS3824-33-Q1 TPS3824-50-Q1, TPS3825-33-Q1, TPS3825-50-Q1, TPS3828-33-Q1, TPS3828-50-Q1 SGLS143C - DECEMBER 2002 - REVISED DECEMBER 2015 www.ti.com Table of Contents 1 2 3 4 5 6 7 8 Features .................................................................. Applications ........................................................... Description ............................................................. Revision History..................................................... Device Comparison Table..................................... Pin Configuration and Functions ......................... Specifications......................................................... 1 1 1 2 3 3 4 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 4 4 4 4 5 6 6 7 Absolute Maximum Ratings ...................................... ESD Ratings.............................................................. Recommended Operating Conditions....................... Thermal Information .................................................. Electrical Characteristics........................................... Timing Requirements ................................................ Switching Characteristics .......................................... Typical Characteristics .............................................. Detailed Description .............................................. 9 8.1 Overview ................................................................... 9 8.2 Functional Block Diagram ......................................... 9 8.3 Feature Description................................................... 9 8.4 Device Functional Modes........................................ 10 9 Application and Implementation ........................ 11 9.1 Application Information............................................ 11 9.2 Typical Applications ................................................ 11 10 Power Supply Recommendations ..................... 12 11 Layout................................................................... 13 11.1 Layout Guidelines ................................................. 13 11.2 Layout Example .................................................... 13 12 Device and Documentation Support ................. 14 12.1 12.2 12.3 12.4 12.5 12.6 Device Support...................................................... Documentation Support ........................................ Community Resources.......................................... Trademarks ........................................................... Electrostatic Discharge Caution ............................ Glossary ................................................................ 14 14 14 14 15 15 13 Mechanical, Packaging, and Orderable Information ........................................................... 15 4 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision B (June 2008) to Revision C Page * Added ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section ................................................................................................. 1 * Added AEC-Q100 Qualified information and Temperature Range to Features .................................................................... 1 * Added -Q1 to all applicable part numbers ............................................................................................................................. 1 * Added FIXED DELAY TIME column to table ........................................................................................................................ 3 2 Submit Documentation Feedback Copyright (c) 2002-2015, Texas Instruments Incorporated Product Folder Links: TPS3820-33-Q1 TPS3820-50-Q1 TPS3823-25-Q1 TPS3823-30-Q1 TPS3823-33-Q1 TPS382350-Q1 TPS3824-30-Q1 TPS3824-33-Q1 TPS3824-50-Q1 TPS3825-33-Q1 TPS3825-50-Q1 TPS3828-33-Q1 TPS3828-50-Q1 TPS3820-33-Q1, TPS3820-50-Q1, TPS3823-25-Q1 TPS3823-30-Q1, TPS3823-33-Q1, TPS3823-50-Q1, TPS3824-30-Q1, TPS3824-33-Q1 TPS3824-50-Q1, TPS3825-33-Q1, TPS3825-50-Q1, TPS3828-33-Q1, TPS3828-50-Q1 www.ti.com SGLS143C - DECEMBER 2002 - REVISED DECEMBER 2015 5 Device Comparison Table DEVICE RESET TPS3820-xx-Q1 TPS3823-xx-Q1 TPS3824-xx-Q1 Push-pull TPS3825-xx-Q1 Push-pull RESET WDI MR FIXED DELAY TIME Push-pull X X 25 ms Push-pull X X 200 ms X Push-pull TPS3828-xx-Q1 Open-drain X 200 ms X 200 ms X 200 ms 6 Pin Configuration and Functions TPS3820-xx-Q1, TPS3823-xx-Q1, TPS3828-xx-Q1: DBV PACKAGE 5-Pin SOT-23 Top View RESET 1 GND 2 MR 3 TPS3824-xx-Q1: DBV PACKAGE 5-Pin SOT-23 Top View VDD 5 4 WDI RESET 1 GND 2 RESET 3 5 VDD 4 WDI TPS3825-xx-Q1: DBV PACKAGE 5-Pin SOT-23 Top View RESET 1 GND 2 RESET 3 5 VDD 4 MR Pin Functions PIN NAME TPS3820xxQ1, TPS3823xxQ1, TPS3828xxQ1 TPS3824xxQ1 TPS3825xxQ1 I/O DESCRIPTION GND 2 2 2 -- MR 3 -- 4 I Manual-reset input. Pull low to force a reset. RESET remains low as long as MR is low and for the time-out period after MR goes high. Leave unconnected or connect to VDD when unused. RESET -- 3 3 O Active-high reset output. Either push-pull or open-drain output stage. RESET 1 1 1 O Active-low reset output. Either push-pull or open-drain output stage. VDD 5 5 5 I Supply voltage. Powers the device and monitors its own voltage. I Watchdog timer input. If WDI remains high or low longer than the time-out period, then reset is triggered. The timer clears when reset is asserted or when WDI sees a rising edge or a falling edge. If unused, the WDI connection must be high impedance to prevent it from causing a reset event. WDI 4 4 Copyright (c) 2002-2015, Texas Instruments Incorporated -- Ground connection Submit Documentation Feedback Product Folder Links: TPS3820-33-Q1 TPS3820-50-Q1 TPS3823-25-Q1 TPS3823-30-Q1 TPS3823-33-Q1 TPS382350-Q1 TPS3824-30-Q1 TPS3824-33-Q1 TPS3824-50-Q1 TPS3825-33-Q1 TPS3825-50-Q1 TPS3828-33-Q1 TPS3828-50-Q1 3 TPS3820-33-Q1, TPS3820-50-Q1, TPS3823-25-Q1 TPS3823-30-Q1, TPS3823-33-Q1, TPS3823-50-Q1, TPS3824-30-Q1, TPS3824-33-Q1 TPS3824-50-Q1, TPS3825-33-Q1, TPS3825-50-Q1, TPS3828-33-Q1, TPS3828-50-Q1 SGLS143C - DECEMBER 2002 - REVISED DECEMBER 2015 www.ti.com 7 Specifications 7.1 Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted) (1) (2) Voltage Current MIN MAX VDD -0.3 6 RESET, RESET, MR, WDI -0.3 (VDD + 0.3) Maximum low output, IOL -5 5 Maximum high output, IOH -5 5 -10 10 Output range (VO < 0 or VO > VDD), IOK Continuous total power dissipation Temperature (1) (2) UNIT V mA See Thermal Information Operating free-air, TA -40 125 Storage, Tstg -65 150 C Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltage values are with respect to GND. 7.2 ESD Ratings VALUE V(ESD) (1) Electrostatic discharge Human-body model (HBM), per AEC Q100-002 (1) 2000 Charged-device model (CDM), per AEC Q100-011 750 UNIT V AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification. 7.3 Recommended Operating Conditions over operating junction temperature range (unless otherwise noted). MIN VDD Supply voltage VI Input voltage VIH High-level input voltage at MR and WDI VIL Low-level input voltage t/V Input transition rise and fall rate at MR or WDI TA Operating free-air temperature range NOM MAX UNIT 1.1 5.5 V 0 VDD + 0.3 V 0.7 x VDD V 0.3 x VDD -40 V 100 ns/V 125 C 7.4 Thermal Information TPS382x-xx-Q1 THERMAL METRIC (1) DBV (SOT-23) UNIT 5 PINS RJA Junction-to-ambient thermal resistance 209.1 C/W RJC(top) Junction-to-case (top) thermal resistance 72.8 C/W RJB Junction-to-board thermal resistance 36.7 C/W JT Junction-to-top characterization parameter 2.1 C/W JB Junction-to-board characterization parameter 35.8 C/W (1) 4 For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report, SPRA953. Submit Documentation Feedback Copyright (c) 2002-2015, Texas Instruments Incorporated Product Folder Links: TPS3820-33-Q1 TPS3820-50-Q1 TPS3823-25-Q1 TPS3823-30-Q1 TPS3823-33-Q1 TPS382350-Q1 TPS3824-30-Q1 TPS3824-33-Q1 TPS3824-50-Q1 TPS3825-33-Q1 TPS3825-50-Q1 TPS3828-33-Q1 TPS3828-50-Q1 TPS3820-33-Q1, TPS3820-50-Q1, TPS3823-25-Q1 TPS3823-30-Q1, TPS3823-33-Q1, TPS3823-50-Q1, TPS3824-30-Q1, TPS3824-33-Q1 TPS3824-50-Q1, TPS3825-33-Q1, TPS3825-50-Q1, TPS3828-33-Q1, TPS3828-50-Q1 www.ti.com SGLS143C - DECEMBER 2002 - REVISED DECEMBER 2015 7.5 Electrical Characteristics over operating junction temperature range (unless otherwise noted) PARAMETER RESET High-level output voltage VOH RESET TEST CONDITIONS TPS382x-25-Q1 VDD = VIT- + 0.2 V, IOH = -20 A TPS382x-30-Q1 TPS382x-33-Q1 VDD = VIT- + 0.2 V, IOH = -30 A TPS382x-50-Q1 VDD = VIT- + 0.2 V IOH = -120 A TPS3824-25-Q1 TPS3825-25-Q1 VDD 1.8 V, IOH = -100 A MIN MAX UNIT 0.8 x VDD VDD - 1.5 V V TPS3824-30-Q1 TPS3825-30-Q1 TPS3824-33-Q1 TPS3825-33-Q1 TYP 0.8 x VDD VDD 1.8 V, IOH = -150 A TPS3824-50-Q1 TPS3825-50-Q1 TPS3824-25-Q1 TPS3825-25-Q1 RESET Low-level output voltage VOL RESET TPS3824-30-Q1 TPS3825-30-Q1 TPS3824-33-Q1 TPS3825-33-Q1 VDD = VIT- + 0.2 V, IOL = 1 mA VDD = VIT- + 0.2 V, IOL = 1.2 mA V TPS3824-50-Q1 TPS3825-50-Q1 VDD = VIT- + 0.2 V, IOL = 3 mA TPS382x-25-Q1 VDD = VIT- - 0.2 V, IOL = 1 mA TPS382x-30-Q1 TPS382x-33-Q1 TPS382x-50-Q1 Power-up reset voltage (1) 0.4 VDD = VIT- - 0.2 V, IOL = 1.2 mA 0.45 VDD = VIT- - 0.2 V, IOL = 3 mA VDD 1.1 V, IOL = 20 A 0.4 TPS382x-25-Q1 2.21 2.25 2.3 2.59 2.63 2.69 2.88 2.93 3 TPS382x-50-Q1 4.49 4.55 4.64 TPS382x-25-Q1 2.19 2.25 2.3 2.55 2.63 2.69 2.84 2.93 3 4.44 4.55 4.64 TPS382x-30-Q1 TPS382x-33-Q1 Negative-going input threshold voltage (2) VIT- TPS382x-30-Q1 TPS382x-33-Q1 TA = 0C to 85C TA = -40C to 125C TPS382x-50-Q1 V V TPS382x-25-Q1 TPS382x-30-Q1 Vhys Hysteresis at VDD input IIH(AV) Average high-level input current IIL(AV) Average low-level input current IIH High-level input current IIL Low-level input current 30 mV TPS382x-33-Q1 TPS382x-50-Q1 50 WDI = VDD, time average (DC = 88%) 120 WDI = 0.3 V, VDD = 5.5 V time average (DC = 12%) -15 WDI WDI = VDD 140 190 MR MR = VDD x 0.7, VDD = 5.5 V -40 -60 WDI WDI = 0.3 V, VDD = 5.5 V 140 190 MR MR = 0.3 V, VDD = 5.5 V -110 -160 WDI A A A TPS382x-25-Q1 IOS Output short-circuit current (3) IDD Supply current RESET TPS382x-30-Q1 TPS382x-33-Q1 -400 VDD = VIT, max + 0.2 V, VO = 0 V TPS382x-50-Q1 -800 WDI, MR, and outputs unconnected Internal pullup resistor at MR Ci (1) (2) (3) Input capacitance at MR, WDI A VI = 0 V to 5.5 V 15 25 A 52 k 5 pF The lowest supply voltage at which RESET becomes active. tr, VDD 15 s/V. To ensure best stability of the threshold voltage, a bypass capacitor (ceramic, 0.1 F) should be placed near the supply terminals. The RESET short-circuit current is the maximum pullup current when RESET is driven low by a microprocessor bidirectional reset pin. Copyright (c) 2002-2015, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: TPS3820-33-Q1 TPS3820-50-Q1 TPS3823-25-Q1 TPS3823-30-Q1 TPS3823-33-Q1 TPS382350-Q1 TPS3824-30-Q1 TPS3824-33-Q1 TPS3824-50-Q1 TPS3825-33-Q1 TPS3825-50-Q1 TPS3828-33-Q1 TPS3828-50-Q1 5 TPS3820-33-Q1, TPS3820-50-Q1, TPS3823-25-Q1 TPS3823-30-Q1, TPS3823-33-Q1, TPS3823-50-Q1, TPS3824-30-Q1, TPS3824-33-Q1 TPS3824-50-Q1, TPS3825-33-Q1, TPS3825-50-Q1, TPS3828-33-Q1, TPS3828-50-Q1 SGLS143C - DECEMBER 2002 - REVISED DECEMBER 2015 www.ti.com 7.6 Timing Requirements At RL = 1 M, CL = 50 pF, and TJ = 25C, unless otherwise noted. MIN tw Pulse width TYP MAX UNIT at VDD VDD = VIT- + 0.2 V, VDD = VIT- - 0.2 V 6 s at MR VDD VIT- + 0.2 V, VIL = 0.3 x VDD, VIH = 0.7 x VDD 1 s at WDI VDD VIT- + 0.2 V, VIL = 0.3 x VDD, VIH = 0.7 x VDD 100 ns 7.7 Switching Characteristics At RL = 1 M, CL = 50 pF, and TA = 25C, unless otherwise noted. PARAMETER ttout Watchdog time out TPS3823/4/8-xx-Q1 TPS3820-xx-Q1 td Delay time tPHL Propagation (delay) time, high-to-low-level output tPLH TPS3823/4/5/8-xx-Q1 Propagation (delay) time, low-to-high-level output VDD TEST CONDITIONS TPS3820-xx-Q1 MIN TYP MAX UNIT VDD VIT- + 0.2 V See Figure 1 112 200 300 ms 0.9 1.6 2.5 s VDD VIT- + 0.2 V See Figure 1 15 25 37 120 200 300 MR to RESET delay (TPS3820/3/5/8-xx-Q1) VDD VIT- + 0.2 V, VIL = 0.3 x VDD, VIH = 0.7 x VDD 0.1 VDD to RESET delay VIL = VIT- - 0.2 V, VIH = VIT- + 0.2 V 25 MR to RESET delay (TPS3824/5-xx-Q1) VDD VIT- + 0.2 V, VIL = 0.3 x VDD, VIH = 0.7 x VDD 0.1 VDD to RESET delay (TPS3824/5-xx-Q1) VIL = VIT- - 0.2 V, VIH = VIT- + 0.2 V 25 ms s s VIT1.1 V td td tt(out) td undefined undefined RESET WDI Figure 1. Delay and Time Out Timing Diagram 6 Submit Documentation Feedback Copyright (c) 2002-2015, Texas Instruments Incorporated Product Folder Links: TPS3820-33-Q1 TPS3820-50-Q1 TPS3823-25-Q1 TPS3823-30-Q1 TPS3823-33-Q1 TPS382350-Q1 TPS3824-30-Q1 TPS3824-33-Q1 TPS3824-50-Q1 TPS3825-33-Q1 TPS3825-50-Q1 TPS3828-33-Q1 TPS3828-50-Q1 TPS3820-33-Q1, TPS3820-50-Q1, TPS3823-25-Q1 TPS3823-30-Q1, TPS3823-33-Q1, TPS3823-50-Q1, TPS3824-30-Q1, TPS3824-33-Q1 TPS3824-50-Q1, TPS3825-33-Q1, TPS3825-50-Q1, TPS3828-33-Q1, TPS3828-50-Q1 www.ti.com SGLS143C - DECEMBER 2002 - REVISED DECEMBER 2015 Normalized Input Threshold Voltage -V IT (TA), VIT (25C) 7.8 Typical Characteristics 19 1.001 1 15 13 0.999 TPS382x-33-Q1 11 0.998 9 7 0.997 5 0.996 3 1 0.995 -40 -15 10 60 35 85 TA - Free-Air Temperature - C i1 i0.5 VOL - Low-Level Output Voltage - V VDD = 5.5 V WDI = Open 0 -40C -100 85C -150 -200 -1 2.5 3.5 4.5 5.5 6.5 VDD = 2.66 V WDI = Open MR = Open 2.5 2 1.5 85C 1 -40C 0.5 0 0 1 2 3 4 5 0 6 2 1 3 4 5 6 7 8 9 10 IOL - Low-Level Output Current - mA VI - Input Voltage at MR - V Figure 4. Input Current vs Input Voltage at MR Figure 5. Low-Level Output Voltage vs Low-Level Output Current 6 3.5 VDD = 3.2 V WDI = Open MR = Open 3 VOH - High-Level Output Voltage - V VOH - High-Level Output Voltage - V 1.5 3 50 -50 0.5 Figure 3. Supply Current vs Supply Voltage Figure 2. Normalized Input Threshold Voltage vs Free-Air Temperature at VDD I I - Input Current - A MR = Open WDI = Open TA = 25C 17 2.5 -40C 2 1.5 85C 1 0.5 0 VDD = 5.5 V WDI = Open MR = Open 5 4 -40C 3 85C 2 1 0 0 -50 -100 -150 -200 -250 IOH - High-Level Output Current - A Figure 6. High-Level Output Voltage vs High-Level Output Current Copyright (c) 2002-2015, Texas Instruments Incorporated 0 -100 -200 -300 -400 -500 -600 -700 IOH - High-Level Output Current - A Figure 7. High-Level Output Voltage vs High-Level Output Current Submit Documentation Feedback Product Folder Links: TPS3820-33-Q1 TPS3820-50-Q1 TPS3823-25-Q1 TPS3823-30-Q1 TPS3823-33-Q1 TPS382350-Q1 TPS3824-30-Q1 TPS3824-33-Q1 TPS3824-50-Q1 TPS3825-33-Q1 TPS3825-50-Q1 TPS3828-33-Q1 TPS3828-50-Q1 7 TPS3820-33-Q1, TPS3820-50-Q1, TPS3823-25-Q1 TPS3823-30-Q1, TPS3823-33-Q1, TPS3823-50-Q1, TPS3824-30-Q1, TPS3824-33-Q1 TPS3824-50-Q1, TPS3825-33-Q1, TPS3825-50-Q1, TPS3828-33-Q1, TPS3828-50-Q1 SGLS143C - DECEMBER 2002 - REVISED DECEMBER 2015 www.ti.com Typical Characteristics (continued) t w - Minimum Pulse Duration at VDD - s 10 WDI = Open MR = Open 8 6 4 2 0 0 200 400 600 800 1000 VDD - Threshold Overdrive - mV Figure 8. Minimum Pulse Duration at VDD vs VDD Threshold Overdrive 8 Submit Documentation Feedback Copyright (c) 2002-2015, Texas Instruments Incorporated Product Folder Links: TPS3820-33-Q1 TPS3820-50-Q1 TPS3823-25-Q1 TPS3823-30-Q1 TPS3823-33-Q1 TPS382350-Q1 TPS3824-30-Q1 TPS3824-33-Q1 TPS3824-50-Q1 TPS3825-33-Q1 TPS3825-50-Q1 TPS3828-33-Q1 TPS3828-50-Q1 TPS3820-33-Q1, TPS3820-50-Q1, TPS3823-25-Q1 TPS3823-30-Q1, TPS3823-33-Q1, TPS3823-50-Q1, TPS3824-30-Q1, TPS3824-33-Q1 TPS3824-50-Q1, TPS3825-33-Q1, TPS3825-50-Q1, TPS3828-33-Q1, TPS3828-50-Q1 www.ti.com SGLS143C - DECEMBER 2002 - REVISED DECEMBER 2015 8 Detailed Description 8.1 Overview The TPS382x-xx-Q1 family of supervisors provide circuit initialization and timing supervision. Optional configurations include devices with active-high and active-low output signals (TPS3824/5-xx-Q1), devices with a watchdog timer (TPS3820/3/4/8-xx-Q1), and devices with manual reset (MR) pins (TPS3820/3/5/8-xx-Q1). RESET asserts when the supply voltage, VDD, rises above 1.1 V. For devices with active-low output logic, the device monitors VDD and keeps RESET low as long as VDD remains below the negative threshold voltage, VIT-. For devices with active-high output logic, RESET remains high as long as VDD remains below VIT-. An internal timer delays the return of the output to the inactive state (high) to ensure proper system reset. The delay time, td, starts after VDD rises above the positive threshold voltage (VIT- + VHYS). When the supply voltage drops below VIT-, the output becomes active (low) again. All the devices of this family have a fixed-sense threshold voltage, VIT-, set by an internal voltage divider, so no external components are required. The TPS382x-xx-Q1 family is designed to monitor supply voltages of 2.5 V, 3 V, 3.3 V, and 5 V. The devices are available in a 5-pin SOT-23 package and are characterized for operation over a temperature range of -40C to 125C, and are qualified in accordance with AEC-Q100 stress test qualification for integrated circuits. 8.2 Functional Block Diagram VDD + _ 52 kW RESET RESET Logic (1) RESET VREF MR (2) Auto-Reset Oscillator 40 kW WDI (3) (1) TPS3824/5-xx-Q1 (2) TPS3820/3/5/8-xx-Q1 (3) TPS3820/3/4/8-xx-Q1 Transition Detector Watchdog Timer Logic 8.3 Feature Description 8.3.1 Manual Reset (MR) The MR input allows an external logic signal from processors, logic circuits, and/or discrete sensors to force a reset signal regardless of VDD with respect to VIT- or the state of the watchdog timer. A low level at MR causes the reset signals to become active. 8.3.2 Active High or Active Low Output All TPS382x-xx-Q1 devices have an active-low logic output (RESET), while the TPS3824/5-xx-Q1 devices also include an active-high logic output (RESET). Copyright (c) 2002-2015, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: TPS3820-33-Q1 TPS3820-50-Q1 TPS3823-25-Q1 TPS3823-30-Q1 TPS3823-33-Q1 TPS382350-Q1 TPS3824-30-Q1 TPS3824-33-Q1 TPS3824-50-Q1 TPS3825-33-Q1 TPS3825-50-Q1 TPS3828-33-Q1 TPS3828-50-Q1 9 TPS3820-33-Q1, TPS3820-50-Q1, TPS3823-25-Q1 TPS3823-30-Q1, TPS3823-33-Q1, TPS3823-50-Q1, TPS3824-30-Q1, TPS3824-33-Q1 TPS3824-50-Q1, TPS3825-33-Q1, TPS3825-50-Q1, TPS3828-33-Q1, TPS3828-50-Q1 SGLS143C - DECEMBER 2002 - REVISED DECEMBER 2015 www.ti.com Feature Description (continued) 8.3.3 Push-Pull or Open-Drain Output All TPS382x-xx-Q1 devices, except for TPS3828-xx-Q1, have push-pull outputs. TPS3828-xx-Q1 devices have an open-drain output. 8.3.4 Watchdog Timer (WDI) TPS3820/3/4/8-xx-Q1 devices have a watchdog timer that must be periodically triggered by either a positive or negative transition at WDI to avoid a reset signal being issued. When the supervising system fails to retrigger the watchdog circuit within the time-out interval, ttout, RESET becomes active for the time period td. This event also reinitializes the watchdog timer. The watchdog timer can be disabled by disconnecting the WDI pin from the system. If the WDI pin detects that it is in a high-impedance state the TPS3820/3/4/8-xx-Q1 will generate its own WDI pulse to ensure that RESET does not assert. If this behavior is not desired place a 1-k resistor from WDI to ground. This resistor will help ensure that the TPS3820/3/4/8-xx-Q1 detects that WDI is not in a high-impedance state. In applications where the input to the WDI pin is active (transitioning high and low) when the TPS3820/3/4/8-xxQ1 is asserting RESET, RESET will be stuck at a logic low after the input voltage returns above VIT-. If the application requires that input to WDI be active when the reset signal is asserted, then use a FET to decouple the WDI signal. An external FET decouples the WDI signal by disconnecting the WDI input when RESET is asserted. For more details on this, see Decoupling WDI During Reset Event for more details. 8.4 Device Functional Modes The device functions according to the inputs and outputs in Table 1. Table 1. Function Table INPUTS (1) (2) 10 (1) OUTPUTS VDD > VIT RESET RESET (2) L 0 L H MR L 1 L H H 0 L H H 1 H L TPS3820/3/5/8-xx-Q1 TPS3824/5-xx-Q1 Submit Documentation Feedback Copyright (c) 2002-2015, Texas Instruments Incorporated Product Folder Links: TPS3820-33-Q1 TPS3820-50-Q1 TPS3823-25-Q1 TPS3823-30-Q1 TPS3823-33-Q1 TPS382350-Q1 TPS3824-30-Q1 TPS3824-33-Q1 TPS3824-50-Q1 TPS3825-33-Q1 TPS3825-50-Q1 TPS3828-33-Q1 TPS3828-50-Q1 TPS3820-33-Q1, TPS3820-50-Q1, TPS3823-25-Q1 TPS3823-30-Q1, TPS3823-33-Q1, TPS3823-50-Q1, TPS3824-30-Q1, TPS3824-33-Q1 TPS3824-50-Q1, TPS3825-33-Q1, TPS3825-50-Q1, TPS3828-33-Q1, TPS3828-50-Q1 www.ti.com SGLS143C - DECEMBER 2002 - REVISED DECEMBER 2015 9 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI's customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality. 9.1 Application Information The TPS382x-xx-Q1 family of devices are very small supervisory circuits that monitor fixed supply voltages of 2.5 V, 3 V, 3.3 V, and 5 V. The TPS382x-xx-Q1 family operates from 1.1 V to 5.5 V. Orderable options include versions with either push-pull or open-drain outputs, versions that use active-high or active-low logic for output signals, versions with a manual reset pin, and versions with a watchdog timer. See the Device Comparison Table for an overview of device options. 9.2 Typical Applications 9.2.1 Supply Rail Monitoring with Watchdog Time-out and 200-ms Delay The TPS3823-xx-Q1 can be used to monitor the supply rail for devices such as microcontrollers. The downstream device is enabled by the TPS3823-xx-Q1 once the voltage on the supply pin (VDD) is above the internal threshold voltage (VIT- + VHYS). The downstream device is disabled by the TPS3823-xx-Q1 when VDD falls below the threshold voltage minus the hysteresis voltage (VIT-). The TPS3823-xx-Q1 also issues a reset signal if the WDI input is not periodically triggered by a positive or negative transition at WDI. When the supervising system fails to retrigger the watchdog circuit within the time-out interval, ttout, RESET becomes active for the time period td. Some applications require a shorter reset signal than the 200 ms that most of the TPS382x-xx-Q1 family provide. In these cases, the TPS3820-xx-Q1is a good choice because it has a delay time of only 25 ms. If an open-drain output is needed, replace the TPS3823-xx-Q1 with the TPS3828-xx-Q1 (if the WDI input must be active while RESET is low, see Decoupling WDI During Reset Event). Figure 9 shows the TPS3823-33-Q1 in a typical application. 3.3 V 100 nF VDD RESET VDD RESET TPS3823-33-Q1 WDI MR GND MSP430C325 I/O GND Figure 9. Supply Rail Monitoring With Watchdog Time-out 9.2.1.1 Design Requirements The TPS3823-33-Q1 must drive the enable pin of a MSP430C325 using a logic-high signal to signify that the supply voltage is above the minimum operating voltage of the device and monitor the I/O pin to determine if the microcontroller is operating correctly. Copyright (c) 2002-2015, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: TPS3820-33-Q1 TPS3820-50-Q1 TPS3823-25-Q1 TPS3823-30-Q1 TPS3823-33-Q1 TPS382350-Q1 TPS3824-30-Q1 TPS3824-33-Q1 TPS3824-50-Q1 TPS3825-33-Q1 TPS3825-50-Q1 TPS3828-33-Q1 TPS3828-50-Q1 11 TPS3820-33-Q1, TPS3820-50-Q1, TPS3823-25-Q1 TPS3823-30-Q1, TPS3823-33-Q1, TPS3823-50-Q1, TPS3824-30-Q1, TPS3824-33-Q1 TPS3824-50-Q1, TPS3825-33-Q1, TPS3825-50-Q1, TPS3828-33-Q1, TPS3828-50-Q1 SGLS143C - DECEMBER 2002 - REVISED DECEMBER 2015 www.ti.com Typical Applications (continued) 9.2.1.2 Detailed Design Procedure Determine which version of the TPS382x-xx-Q1 family best suits the functional performance required. If the input supply is noisy, include an input capacitor to help avoid unwanted changes to the reset signal. 9.2.1.3 Application Curve t w - Minimum Pulse Duration at VDD - s 10 WDI = Open MR = Open 8 6 4 2 0 0 200 400 600 800 1000 VDD - Threshold Overdrive - mV Figure 10. Minimum Pulse Duration at VDD vs VDD Threshold Overdrive 9.2.2 Decoupling WDI During Reset Event If the application requires that the input to WDI is active when the reset signal is asserted, Figure 11 shows how to decouple WDI from the active signal using an N-channel FET. The N-channel FET is placed in series with the WDI pin, with the gate of the FET connected to the RESET output. 3.3 V VDD VDD RESET RESET TPS3820-33-Q1 MR WDI Microprocessor I/O GND GND Figure 11. WDI Example 10 Power Supply Recommendations These devices are designed to operate from an input supply with a voltage range from 1.1 V to 5.5 V. Though not required, it is good analog design practice to place a 0.1-F ceramic capacitor close to the VDD pin if the input supply is noisy. 12 Submit Documentation Feedback Copyright (c) 2002-2015, Texas Instruments Incorporated Product Folder Links: TPS3820-33-Q1 TPS3820-50-Q1 TPS3823-25-Q1 TPS3823-30-Q1 TPS3823-33-Q1 TPS382350-Q1 TPS3824-30-Q1 TPS3824-33-Q1 TPS3824-50-Q1 TPS3825-33-Q1 TPS3825-50-Q1 TPS3828-33-Q1 TPS3828-50-Q1 TPS3820-33-Q1, TPS3820-50-Q1, TPS3823-25-Q1 TPS3823-30-Q1, TPS3823-33-Q1, TPS3823-50-Q1, TPS3824-30-Q1, TPS3824-33-Q1 TPS3824-50-Q1, TPS3825-33-Q1, TPS3825-50-Q1, TPS3828-33-Q1, TPS3828-50-Q1 www.ti.com SGLS143C - DECEMBER 2002 - REVISED DECEMBER 2015 11 Layout 11.1 Layout Guidelines Follow these guidelines to lay out the printed-circuit-board (PCB) that is used for the TPS382x-xx-Q1 family of devices. * Place the VDD decoupling capacitor (CVDD) close to the device. * Avoid using long traces for the VDD supply node. The VDD capacitor (CVDD), along with parasitic inductance from the supply to the capacitor, can form an LC tank and create ringing with peak voltages above the maximum VDD voltage. 11.2 Layout Example Pullup Voltage CVDD RESET Flag TPS3828-xx-Q1 1 5 2 MR Signal 3 4 WDI Signal Figure 12. Example Layout (DBV Package) Copyright (c) 2002-2015, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: TPS3820-33-Q1 TPS3820-50-Q1 TPS3823-25-Q1 TPS3823-30-Q1 TPS3823-33-Q1 TPS382350-Q1 TPS3824-30-Q1 TPS3824-33-Q1 TPS3824-50-Q1 TPS3825-33-Q1 TPS3825-50-Q1 TPS3828-33-Q1 TPS3828-50-Q1 13 TPS3820-33-Q1, TPS3820-50-Q1, TPS3823-25-Q1 TPS3823-30-Q1, TPS3823-33-Q1, TPS3823-50-Q1, TPS3824-30-Q1, TPS3824-33-Q1 TPS3824-50-Q1, TPS3825-33-Q1, TPS3825-50-Q1, TPS3828-33-Q1, TPS3828-50-Q1 SGLS143C - DECEMBER 2002 - REVISED DECEMBER 2015 www.ti.com 12 Device and Documentation Support 12.1 Device Support 12.1.1 Development Support 12.1.1.1 Spice Models Computer simulation of circuit performance using SPICE is often useful when analyzing the performance of analog circuits and systems. A SPICE model for the TPS382xx-Q1 is available through the product folders under Tools & Software. 12.2 Documentation Support 12.2.1 Related Documentation * Disabling the Watchdog Timer for TI's Family of Supervisors, SLVA145 12.2.1.1 Related Links The table below lists quick access links. Categories include technical documents, support and community resources, tools and software, and quick access to sample or buy. Table 2. Related Links PARTS PRODUCT FOLDER SAMPLE & BUY TECHNICAL DOCUMENTS TOOLS & SOFTWARE SUPPORT & COMMUNITY TPS3820-33-Q1 Click here Click here Click here Click here Click here TPS3820-50-Q1 Click here Click here Click here Click here Click here TPS3823-25-Q1 Click here Click here Click here Click here Click here TPS3823-30-Q1 Click here Click here Click here Click here Click here TPS3823-33-Q1 Click here Click here Click here Click here Click here TPS3823-50-Q1 Click here Click here Click here Click here Click here TPS3824-30-Q1 Click here Click here Click here Click here Click here TPS3824-33-Q1 Click here Click here Click here Click here Click here TPS3824-50-Q1 Click here Click here Click here Click here Click here TPS3825-33-Q1 Click here Click here Click here Click here Click here TPS3825-50-Q1 Click here Click here Click here Click here Click here TPS3828-33-Q1 Click here Click here Click here Click here Click here TPS3828-50-Q1 Click here Click here Click here Click here Click here 12.3 Community Resources The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use. TI E2ETM Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help solve problems with fellow engineers. Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and contact information for technical support. 12.4 Trademarks E2E is a trademark of Texas Instruments. All other trademarks are the property of their respective owners. 14 Submit Documentation Feedback Copyright (c) 2002-2015, Texas Instruments Incorporated Product Folder Links: TPS3820-33-Q1 TPS3820-50-Q1 TPS3823-25-Q1 TPS3823-30-Q1 TPS3823-33-Q1 TPS382350-Q1 TPS3824-30-Q1 TPS3824-33-Q1 TPS3824-50-Q1 TPS3825-33-Q1 TPS3825-50-Q1 TPS3828-33-Q1 TPS3828-50-Q1 TPS3820-33-Q1, TPS3820-50-Q1, TPS3823-25-Q1 TPS3823-30-Q1, TPS3823-33-Q1, TPS3823-50-Q1, TPS3824-30-Q1, TPS3824-33-Q1 TPS3824-50-Q1, TPS3825-33-Q1, TPS3825-50-Q1, TPS3828-33-Q1, TPS3828-50-Q1 www.ti.com SGLS143C - DECEMBER 2002 - REVISED DECEMBER 2015 12.5 Electrostatic Discharge Caution These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 12.6 Glossary SLYZ022 -- TI Glossary. This glossary lists and explains terms, acronyms, and definitions. 13 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. Copyright (c) 2002-2015, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: TPS3820-33-Q1 TPS3820-50-Q1 TPS3823-25-Q1 TPS3823-30-Q1 TPS3823-33-Q1 TPS382350-Q1 TPS3824-30-Q1 TPS3824-33-Q1 TPS3824-50-Q1 TPS3825-33-Q1 TPS3825-50-Q1 TPS3828-33-Q1 TPS3828-50-Q1 15 PACKAGE OPTION ADDENDUM www.ti.com 4-Mar-2016 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) 2T25-50QFRG4Q1 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 PDFQ 2T28-33QDBVRG4Q1 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 PDIQ 2U3820-50QDBVRG4Q1 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 PDDQ 2U3823-25QDBVRG4Q1 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 PAPQ 2U3823-30QDBVRG4Q1 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 PAQQ 2U3823-33QDBVRG4Q1 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 PARQ 2U3823-50QDBVRG4Q1 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 PASQ 2U3824-33QDBVRG4Q1 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 PAVQ 2U3824-50QDBVRG4Q1 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 PAWQ 2U3825-33QDBVRG4Q1 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 PDGQ TPS3820-33QDBVRQ1 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 PDEQ TPS3820-50DBVRQ1G4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 PKG4 TPS3820-50QDBVRQ1 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 PDDQ TPS3823-25QDBVRQ1 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 PAPQ TPS3823-30QDBVRQ1 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 PAQQ TPS3823-33QDBVRQ1 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 PARQ TPS3823-50QDBVRQ1 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 PASQ Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 4-Mar-2016 Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) TPS3824-25QDBVRQ1 OBSOLETE SOT-23 DBV 5 TBD Call TI Call TI -40 to 125 TPS3824-30QDBVRQ1 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 PAUQ TPS3824-33QDBVRQ1 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 PAVQ TPS3824-50QDBVRQ1 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 PAWQ TPS3825-33QDBVRQ1 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 PDGQ TPS3825-50QDBVRQ1 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 PDFQ TPS3828-33QDBVRQ1 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 PDIQ TPS3828-50QDBVRG4Q ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 PDHQ (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. Addendum-Page 2 Samples PACKAGE OPTION ADDENDUM www.ti.com 4-Mar-2016 (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF TPS3820-33-Q1, TPS3820-50-Q1, TPS3823-25-Q1, TPS3823-30-Q1, TPS3823-33-Q1, TPS3823-50-Q1, TPS3824-25-Q1, TPS3824-30-Q1, TPS3824-33-Q1, TPS3824-50-Q1, TPS3825-33-Q1, TPS3825-50-Q1, TPS3828-33-Q1, TPS3828-50-Q1 : * Catalog: TPS3820-33, TPS3820-50, TPS3823-25, TPS3823-30, TPS3823-33, TPS3823-50, TPS3824-25, TPS3824-30, TPS3824-33, TPS3824-50, TPS3825-33, TPS3825-50, TPS3828-33, TPS3828-50 NOTE: Qualified Version Definitions: * Catalog - TI's standard catalog product Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 23-Oct-2015 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2T25-50QFRG4Q1 SOT-23 DBV 5 3000 180.0 9.0 2T28-33QDBVRG4Q1 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 3.15 3.2 1.4 4.0 8.0 Q3 SOT-23 DBV 5 3000 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 2U3820-50QDBVRG4Q1 SOT-23 DBV 5 3000 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 2U3823-25QDBVRG4Q1 SOT-23 DBV 5 3000 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 2U3823-30QDBVRG4Q1 SOT-23 DBV 5 3000 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 2U3823-33QDBVRG4Q1 SOT-23 DBV 5 3000 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 2U3823-50QDBVRG4Q1 SOT-23 DBV 5 3000 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 2U3824-33QDBVRG4Q1 SOT-23 DBV 5 3000 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 2U3824-50QDBVRG4Q1 SOT-23 DBV 5 3000 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 2U3825-33QDBVRG4Q1 SOT-23 DBV 5 3000 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 TPS3820-33QDBVRQ1 SOT-23 DBV 5 3000 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 TPS3820-50DBVRQ1G4 SOT-23 DBV 5 3000 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 TPS3820-50QDBVRQ1 SOT-23 DBV 5 3000 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 TPS3823-25QDBVRQ1 SOT-23 DBV 5 3000 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 TPS3823-30QDBVRQ1 SOT-23 DBV 5 3000 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 TPS3823-33QDBVRQ1 SOT-23 DBV 5 3000 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 TPS3823-50QDBVRQ1 SOT-23 DBV 5 3000 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 TPS3824-30QDBVRQ1 SOT-23 DBV 5 3000 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 23-Oct-2015 Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) TPS3824-33QDBVRQ1 SOT-23 DBV 5 3000 180.0 9.0 TPS3824-50QDBVRQ1 SOT-23 DBV 5 3000 180.0 9.0 TPS3825-33QDBVRQ1 SOT-23 DBV 5 3000 180.0 TPS3825-50QDBVRQ1 SOT-23 DBV 5 3000 180.0 TPS3828-33QDBVRQ1 SOT-23 DBV 5 3000 TPS3828-50QDBVRG4Q SOT-23 DBV 5 3000 W Pin1 (mm) Quadrant 3.15 3.2 1.4 4.0 8.0 Q3 3.15 3.2 1.4 4.0 8.0 Q3 9.0 3.15 3.2 1.4 4.0 8.0 Q3 9.0 3.15 3.2 1.4 4.0 8.0 Q3 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 180.0 9.0 3.15 3.2 1.4 4.0 8.0 Q3 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) 2T25-50QFRG4Q1 SOT-23 DBV 5 3000 182.0 182.0 20.0 2T28-33QDBVRG4Q1 SOT-23 DBV 5 3000 182.0 182.0 20.0 2U3820-50QDBVRG4Q1 SOT-23 DBV 5 3000 182.0 182.0 20.0 2U3823-25QDBVRG4Q1 SOT-23 DBV 5 3000 182.0 182.0 20.0 2U3823-30QDBVRG4Q1 SOT-23 DBV 5 3000 182.0 182.0 20.0 2U3823-33QDBVRG4Q1 SOT-23 DBV 5 3000 182.0 182.0 20.0 2U3823-50QDBVRG4Q1 SOT-23 DBV 5 3000 182.0 182.0 20.0 2U3824-33QDBVRG4Q1 SOT-23 DBV 5 3000 182.0 182.0 20.0 2U3824-50QDBVRG4Q1 SOT-23 DBV 5 3000 182.0 182.0 20.0 2U3825-33QDBVRG4Q1 SOT-23 DBV 5 3000 182.0 182.0 20.0 TPS3820-33QDBVRQ1 SOT-23 DBV 5 3000 182.0 182.0 20.0 Pack Materials-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 23-Oct-2015 Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS3820-50DBVRQ1G4 SOT-23 DBV 5 3000 182.0 182.0 20.0 TPS3820-50QDBVRQ1 SOT-23 DBV 5 3000 182.0 182.0 20.0 TPS3823-25QDBVRQ1 SOT-23 DBV 5 3000 182.0 182.0 20.0 TPS3823-30QDBVRQ1 SOT-23 DBV 5 3000 182.0 182.0 20.0 TPS3823-33QDBVRQ1 SOT-23 DBV 5 3000 182.0 182.0 20.0 TPS3823-50QDBVRQ1 SOT-23 DBV 5 3000 182.0 182.0 20.0 TPS3824-30QDBVRQ1 SOT-23 DBV 5 3000 182.0 182.0 20.0 TPS3824-33QDBVRQ1 SOT-23 DBV 5 3000 182.0 182.0 20.0 TPS3824-50QDBVRQ1 SOT-23 DBV 5 3000 182.0 182.0 20.0 TPS3825-33QDBVRQ1 SOT-23 DBV 5 3000 182.0 182.0 20.0 TPS3825-50QDBVRQ1 SOT-23 DBV 5 3000 182.0 182.0 20.0 TPS3828-33QDBVRQ1 SOT-23 DBV 5 3000 182.0 182.0 20.0 TPS3828-50QDBVRG4Q SOT-23 DBV 5 3000 182.0 182.0 20.0 Pack Materials-Page 3 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2016, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: TPS3828-33QDBVRQ1 2T28-33QDBVRG4Q1