DS1307+. - MAXIM INTEGRATED PRODUCTS

1 of 15 REV: 071405

Note: Some revisions of this device may incorporate deviations from published specifications known as errata. Multiple revisions of any device

may be simultaneously available through various sales channels. For information about device errata, click here: www.maxim-ic.com/errata.

GENERAL DESCRIPTION

The DS1307 serial real-time clock (RTC) is a

low-power, full binary-coded decimal (BCD)

clock/calendar plus 56 bytes of NV SRAM.

Address and data are transferred serially through

an I2C*, bidirectional bus. The clock/calendar

provides seconds, minutes, hours, day, date,

month, and year information. The end of the

month date is automatically adjusted for months

with fewer than 31 days, including corrections for

leap year. The clock operates in either the 24-

hour or 12-hour format with AM/PM indicator.

The DS1307 has a built-in power-sense circuit

that detects power failures and automatically

switches to the battery supply.

* I2C is a trademark of Philips Corp. Purchase of I2C components of

Maxim Integrated Products, Inc., or one of its sublicensed

Associated Companies, conveys a license under the Philips I2C

Patent Rights to use these components in an I2C system, provided

that the system conforms to the I2C Standard Specification as

defined by Philips Corp.

FEATURES

§ Real-Time Clock (RTC) Counts Seconds,

Minutes, Hours, Date of the Month, Month,

Day of the week, and Year with Leap-Year

Compensation Valid Up to 2100

§ 56-Byte, Battery-Backed, Nonvolatile (NV)

RAM for Data Storage

§ I2C Serial Interface

§ Programmable Square-Wave Output Signal

§ Automatic Power-Fail Detect and Switch

Circuitry

§ Consumes Less than 500nA in Battery-

Backup Mode with Oscillator Running

§ Optional Industrial Temperature Range:

-40°C to +85°C

§ Available in 8-Pin Plastic DIP or SO

§ Underwriters Laboratory (UL) Recognized

Typical Operating Circuit and Pin Configurations appear

at end of data sheet.

ORDERING INFORMATION

PART TEMP RANGE

VOLTAGE

(V) PIN-PACKAGE TOP MARK*

DS1307 0°C to +70°C 5.0 8 PDIP (300 mils) DS1307

DS1307+ 0°C to +70°C 5.0 8 PDIP (300 mils) DS1307

DS1307N -40°C to +85°C 5.0 8 PDIP (300 mils) DS1307

DS1307Z 0°C to +70°C 5.0 8 SO (150 mils) DS1307

DS1307Z+ 0°C to +70°C 5.0 8 SO (150 mils) DS1307

DS1307ZN -40°C to +85°C 5.0 8 SO (150 mils) DS1307N

DS1307ZN+ -40°C to +85°C 5.0 8 SO (150 mils) DS1307N

DS1307Z/T&R 0°C to +70°C 5.0 8 SO (150 mils) Tape and Reel DS1307

DS1307Z+T&R 0°C to +70°C 5.0 8 SO (150 mils) Tape and Reel DS1307

DS1307ZN/T&R -40°C to +85°C 5.0 8 SO (150 mils) Tape and Reel DS1307N

DS1307ZN+T&R -40°C to +85°C 5.0 8 SO (150 mils) Tape and Reel DS1307N

+ Denotes a lead-free/RoHS-compliant device.

* A “+” anywhere on the top mark indicates a lead-free device. An “N” on the lower left corner of the top mark indicates an industrial

temperature grade device.

DS1307

64 x 8, Serial, I2C Real-Time Clock

DS1307 64 x 8, Serial, I2C Real-Time Clock

2 of 15

ABSOLUTE MAXIMUM RATINGS

Voltage Range on Any Pin Relative to Ground……….……………………….…………....-0.5V to +7.0V

Operating Temperature Range (Noncondensing)

Commercial…………………….……………………………….………………………..0°C to +70°C

Industrial………………………………………………………………………………-40°C to +85°C

Storage Temperature Range………………………………………...…………..…………-55°C to +125°C

Soldering Temperature (DIP, leads)..…………………………………………….....+260°C for 10 seconds

Soldering Temperature (surface mount)…..……………………….See JPC/JEDEC Standard J-STD-020A

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only,

and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is

not implied. Exposure to the absolute maximum rating conditions for extended periods may affect device reliability.

RECOMMENDED DC OPERATING CONDITIONS

(TA = 0°C to +70°C, TA = -40°C to +85°C.) (Notes 1, 2)

PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS

Supply Voltage VCC 4.5 5.0 5.5 V

Logic 1 Input VIH 2.2 VCC + 0.3 V

Logic 0 Input VIL -0.3 +0.8 V

VBAT Battery Voltage VBAT 2.0 3 3.5 V

DC ELECTRICAL CHARACTERISTICS

(VCC = 4.5V to 5.5V; TA = 0°C to +70°C, TA = -40°C to +85°C.) (Notes 1, 2)

PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS

Input Leakage (SCL) ILI -1 1 mA

I/O Leakage (SDA, SQW/OUT) ILO -1 1 mA

Logic 0 Output (IOL = 5mA) VOL 0.4 V

Active Supply Current

(fSCL = 100kHz) ICCA 1.5 mA

Standby Current ICCS (Note 3) 200 mA

VBAT Leakage Current IBATLKG 5 50 nA

Power-Fail Voltage (VBAT = 3.0V) VPF 1.216 x

VBAT

1.25 x

VBAT

1.284 x

VBAT V

DC ELECTRICAL CHARACTERISTICS

(VCC = 0V, VBAT = 3.0V; TA = 0°C to +70°C, TA = -40°C to +85°C.) (Notes 1, 2)

PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS

VBAT Current (OSC ON);

SQW/OUT OFF IBAT1 300 500 nA

VBAT Current (OSC ON);

SQW/OUT ON (32kHz) IBAT2 480 800 nA

VBAT Data-Retention Current

(Oscillator Off) IBATDR 10 100 nA

DS1307 64 x 8, Serial, I2C Real-Time Clock

3 of 15

AC ELECTRICAL CHARACTERISTICS

(VCC = 4.5V to 5.5V; TA = 0°C to +70°C, TA = -40°C to +85°C.)

PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS

SCL Clock Frequency fSCL 0 100 kHz

Bus Free Time Between a STOP and

START Condition tBUF 4.7 ms

Hold Time (Repeated) START

Condition tHD:STA (Note 4) 4.0 ms

LOW Period of SCL Clock tLOW 4.7 ms

HIGH Period of SCL Clock tHIGH 4.0 ms

Setup Time for a Repeated START

Condition tSU:STA 4.7 ms

Data Hold Time tHD:DAT 0 ms

Data Setup Time tSU:DAT (Notes 5, 6) 250 ns

Rise Time of Both SDA and SCL

Signals tR 1000 ns

Fall Time of Both SDA and SCL

Signals tF 300 ns

Setup Time for STOP Condition tSU:STO 4.7 ms

CAPACITANCE

(TA = +25°C)

PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS

Pin Capacitance (SDA, SCL) CI/O 10 pF

Capacitance Load for Each Bus

Line CB (Note 7) 400 pF

Note 1: All voltages are referenced to ground.

Note 2: Limits at -40°C are guaranteed by design and are not production tested.

Note 3: ICCS specified with VCC = 5.0V and SDA, SCL = 5.0V.

Note 4: After this period, the first clock pulse is generated.

Note 5: A device must internally provide a hold time of at least 300ns for the SDA signal (referred to the VIH(MIN) of the

SCL signal) to bridge the undefined region of the falling edge of SCL.

Note 6: The maximum tHD:DAT only has to be met if the device does not stretch the LOW period (tLOW) of the SCL signal.

Note 7: CB—total capacitance of one bus line in pF.

DS1307 64 x 8, Serial, I2C Real-Time Clock

4 of 15

TIMING DIAGRAM

Figure 1. Block Diagram

START

SDA

STOP

SCL

tSU:STO

tHD:STA

tSU:STA

REPEATED

START

HD:DAT

tHIGH

LOW t

tHD:STA

BUF

SU:DAT

SERIAL BUS

INTERFACE

AND ADDRESS

DECODE

OSCILLATOR

CONTROL

LOGIC

SCL

SDA

1Hz/4.096kHz/

8.192kHz/32.768kHz

MUX/BUFFER

SQW/OUT

USER BUFFER

(7 BYTES)

CLOCK AND

CALENDAR

REGISTERS

32,768Hz

1Hz

POWER

CONTROL

vcc

VBAT

DIVIDER

CHAIN

RAM

GND

DS1307

DS1307 64 x 8, Serial, I2C Real-Time Clock

5 of 15

TYPICAL OPERATING CHARACTERISTICS

(VCC = 5.0V, TA = +25°C, unless otherwise noted.)

ICCS vs. VCC

100

110

120

1.0 2.0 3.0 4.0 5.0

VCC (V)

SUPPLY CURRENT (uA

)

VBAT=3.0V

IBAT vs. Temperature

175.0

225.0

275.0

325.0

-40-20 0 20406080

TEMPERATURE (°C)

SUPPLY CURRENT (nA

)

VCC=0V, VBAT=3.0

SQW=32kHz

SQW off

IBAT vs. VBAT

100

150

200

250

300

350

400

2.0 2.5 3.0 3.5

VBACKUP (V)

SUPPLY CURRENT (nA

)

SQW=32kHz

SQW of f

VCC = 0V

SQW/OUT vs. Supply Voltage

32768

32768.1

32768.2

32768.3

32768.4

32768.5

32768.6

32768.7

32768.8

32768.9

32769

2.02.53.03.54.04.55.05.5

Supply (V)

FREQUENCY (Hz)

DS1307 64 x 8, Serial, I2C Real-Time Clock

6 of 15

PIN DESCRIPTION

PIN NAME FUNCTION

1 X1

2 X2

Connections for Standard 32.768kHz Quartz Crystal. The internal oscillator circuitry is

designed for operation with a crystal having a specified load capacitance (CL) of 12.5pF.

X1 is the input to the oscillator and can optionally be connected to an external 32.768kHz

oscillator. The output of the internal oscillator, X2, is floated if an external oscillator is

connected to X1.

Note: For more information on crystal selection and crystal layout considerations, refer to

Application Note 58: Crystal Considerations with Dallas Real-Time Clocks.

3 VBAT

Backup Supply Input for Any Standard 3V Lithium Cell or Other Energy Source. Battery

voltage must be held between the minimum and maximum limits for proper operation.

Diodes in series between the battery and the VBAT pin may prevent proper operation. If a

backup supply is not required, VBAT must be grounded. The nominal power-fail trip point

(VPF) voltage at which access to the RTC and user RAM is denied is set by the internal

circuitry as 1.25 x VBAT nominal. A lithium battery with 48mAhr or greater will back up

the DS1307 for more than 10 years in the absence of power at +25°C.

UL recognized to ensure against reverse charging current when used with a lithium

battery.

4 GND Ground

5 SDA

Serial Data Input/Output. SDA is the data input/output for the I2C serial interface. The

SDA pin is open drain and requires an external pullup resistor.

6 SCL

Serial Clock Input. SCL is the clock input for the I2C interface and is used to synchronize

data movement on the serial interface.

7 SWQ/OUT

Square Wave/Output Driver. When enabled, the SQWE bit set to 1, the SQW/OUT pin

outputs one of four square-wave frequencies (1Hz, 4kHz, 8kHz, 32kHz). The SQW/OUT

pin is open drain and requires an external pullup resistor. SQW/OUT operates with either

VCC or VBAT applied.

8 VCC

Primary Power Supply. When voltage is applied within normal limits, the device is fully

accessible and data can be written and read. When a backup supply is connected to the

device and VCC is below VTP, read and writes are inhibited. However, the timekeeping

function continues unaffected by the lower input voltage.

DETAILED DESCRIPTION

The DS1307 is a low-power clock/calendar with 56 bytes of battery-backed SRAM. The clock/calendar

provides seconds, minutes, hours, day, date, month, and year information. The date at the end of the

month is automatically adjusted for months with fewer than 31 days, including corrections for leap year.

The DS1307 operates as a slave device on the I2C bus. Access is obtained by implementing a START

condition and providing a device identification code followed by a register address. Subsequent registers

can be accessed sequentially until a STOP condition is executed. When VCC falls below 1.25 x VBAT, the

device terminates an access in progress and resets the device address counter. Inputs to the device will not

be recognized at this time to prevent erroneous data from being written to the device from an out-of-

tolerance system. When VCC falls below VBAT, the device switches into a low-current battery-backup

mode. Upon power-up, the device switches from battery to VCC when VCC is greater than VBAT +0.2V and

recognizes inputs when VCC is greater than 1.25 x VBAT. The block diagram in Figure 1 shows the main

elements of the serial RTC.

DS1307 64 x 8, Serial, I2C Real-Time Clock

7 of 15

OSCILLATOR CIRCUIT

The DS1307 uses an external 32.768kHz crystal. The oscillator circuit does not require any external

resistors or capacitors to operate. Table 1 specifies several crystal parameters for the external crystal.

Figure 3 shows a functional schematic of the oscillator circuit. If using a crystal with the specified

characteristics, the startup time is usually less than one second.

CLOCK ACCURACY

The accuracy of the clock is dependent upon the accuracy of the crystal and the accuracy of the match

between the capacitive load of the oscillator circuit and the capacitive load for which the crystal was

trimmed. Additional error will be added by crystal frequency drift caused by temperature shifts. External

circuit noise coupled into the oscillator circuit may result in the clock running fast. Refer to Application

Note 58: Crystal Considerations with Dallas Real-Time Clocks for detailed information.

Table 1. Crystal Specifications*

PARAMETER SYMBOL MIN TYP MAX UNITS

Nominal Frequency fO 32.768 kHz

Series Resistance ESR 45 kW

Load Capacitance CL 12.5 pF

*The crystal, traces, and crystal input pins should be isolated from RF generating signals. Refer to

Application Note 58: Crystal Considerations for Dallas Real-Time Clocks for additional specifications.

Figure 2. Recommended Layout for Crystal

NOTE: AVOID ROUTING SIGNAL LINES IN THE CROSSHATCHED

REA (UPPER LEFT QUADRANT) OF THE PACKAGE UNLESS

THERE IS A GROUND PLANE BETWEEN THE SIGNAL LINE AND THE

DEVICE PACKAGE.

LOCAL GROUND PLANE (LAYER 2)

CRYSTAL

GND

DS1307 64 x 8, Serial, I2C Real-Time Clock

8 of 15

Figure 3. Oscillator Circuit Showing Internal Bias Network

RTC AND RAM ADDRESS MAP

Table 2 shows the address map for the DS1307 RTC and RAM registers. The RTC registers are located in

address locations 00h to 07h. The RAM registers are located in address locations 08h to 3Fh. During a

multibyte access, when the address pointer reaches 3Fh, the end of RAM space, it wraps around to

location 00h, the beginning of the clock space.

CLOCK AND CALENDAR

The time and calendar information is obtained by reading the appropriate register bytes. Table 2 shows

the RTC registers. The time and calendar are set or initialized by writing the appropriate register bytes.

The contents of the time and calendar registers are in the BCD format. The day-of-week register

increments at midnight. Values that correspond to the day of week are user-defined but must be

sequential (i.e., if 1 equals Sunday, then 2 equals Monday, and so on.) Illogical time and date entries

result in undefined operation. Bit 7 of Register 0 is the clock halt (CH) bit. When this bit is set to 1, the

oscillator is disabled. When cleared to 0, the oscillator is enabled.

Please note that the initial power-on state of all registers is not defined. Therefore, it is important to

enable the oscillator (CH bit = 0) during initial configuration.

The DS1307 can be run in either 12-hour or 24-hour mode. Bit 6 of the hours register is defined as the

12-hour or 24-hour mode-select bit. When high, the 12-hour mode is selected. In the 12-hour mode, bit 5

is the AM/PM bit with logic high being PM. In the 24-hour mode, bit 5 is the second 10-hour bit (20 to

23 hours). The hours value must be re-entered whenever the 12/24-hour mode bit is changed.

When reading or writing the time and date registers, secondary (user) buffers are used to prevent errors

when the internal registers update. When reading the time and date registers, the user buffers are

synchronized to the internal registers on any I2C START. The time information is read from these

secondary registers while the clock continues to run. This eliminates the need to re-read the registers in

case the internal registers update during a read. The divider chain is reset whenever the seconds register is

written. Write transfers occur on the I2C acknowledge from the DS1307. Once the divider chain is reset,

to avoid rollover issues, the remaining time and date registers must be written within one second.

COUNTDOWN

CHAIN

X1 X2

CRYSTAL

RTC

REGISTERS

CL1 CL2

DS1307 RTC

DS1307 64 x 8, Serial, I2C Real-Time Clock

9 of 15

Table 2. Timekeeper Registers

ADDRESS Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 FUNCTION RANGE

00H CH 10 Seconds Seconds Seconds 00–59

01H 0 10 Minutes Minutes Minutes 00–59

12 10 Hour

02H 0

24 PM/AM

10 Hour Hours Hours

1–12

+AM/PM

00–23

03H 0 0 0 0 0 DAY Day 01–07

04H 0 0 10 Date Date Date 01–31

05H 0 0 0

Month Month Month 01–12

06H 10 Year Year Year 00–99

07H OUT 0 0 SQWE 0 0 RS1 RS0 Control —

08H-3FH RAM 56 x 8 00H–FFH

0 = Always reads back as 0.

CONTROL REGISTER

The DS1307 control register is used to control the operation of the SQW/OUT pin.

BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0

OUT 0 0 SQWE 0 0 RS1 RS0

Bit 7: Output Control (OUT). This bit controls the output level of the SQW/OUT pin when the square-

wave output is disabled. If SQWE = 0, the logic level on the SQW/OUT pin is 1 if OUT = 1 and is 0 if

OUT = 0.

Bit 4: Square-Wave Enable (SQWE). This bit, when set to logic 1, enables the oscillator output. The

frequency of the square-wave output depends upon the value of the RS0 and RS1 bits. With the square-

wave output set to 1Hz, the clock registers update on the falling edge of the square wave.

Bits 1, 0: Rate Select (RS1, RS0). These bits control the frequency of the square-wave output when the

square-wave output has been enabled. The following table lists the square-wave frequencies that can be

selected with the RS bits.

RS1 RS0 SQUARE-WAVE

OUTPUT FREQUENCY

0 0 1Hz

0 1 4.096kHz

1 0 8.192kHz

1 1 32.768kHz

DS1307 64 x 8, Serial, I2C Real-Time Clock

10 of 15

I2C DATA BUS

The DS1307 supports the I2C protocol. A device that sends data onto the bus is defined as a transmitter

and a device receiving data as a receiver. The device that controls the message is called a master. The

devices that are controlled by the master are referred to as slaves. The bus must be controlled by a master

device that generates the serial clock (SCL), controls the bus access, and generates the START and STOP

conditions. The DS1307 operates as a slave on the I2C bus.

Figures 4, 5, and 6 detail how data is transferred on the I2C bus.

§ Data transfer may be initiated only when the bus is not busy.

§ During data transfer, the data line must remain stable whenever the clock line is HIGH. Changes in

the data line while the clock line is high will be interpreted as control signals.

Accordingly, the following bus conditions have been defined:

Bus not busy: Both data and clock lines remain HIGH.

Start data transfer: A change in the state of the data line, from HIGH to LOW, while the clock is

HIGH, defines a START condition.

Stop data transfer: A change in the state of the data line, from LOW to HIGH, while the clock line

is HIGH, defines the STOP condition.

Data valid: The state of the data line represents valid data when, after a START condition, the data

line is stable for the duration of the HIGH period of the clock signal. The data on the line must be

changed during the LOW period of the clock signal. There is one clock pulse per bit of data.

Each data transfer is initiated with a START condition and terminated with a STOP condition. The

number of data bytes transferred between START and STOP conditions is not limited, and is

determined by the master device. The information is transferred byte-wise and each receiver

acknowledges with a ninth bit. Within the 2-wire bus specifications a standard mode (100kHz clock

rate) and a fast mode (400kHz clock rate) are defined. The DS1307 operates in the standard mode

(100kHz) only.

Acknowledge: Each receiving device, when addressed, is obliged to generate an acknowledge after

the reception of each byte. The master device must generate an extra clock pulse which is associated

with this acknowledge bit.

A device that acknowledges must pull down the SDA line during the acknowledge clock pulse in

such a way that the SDA line is stable LOW during the HIGH period of the acknowledge related

clock pulse. Of course, setup and hold times must be taken into account. A master must signal an

end of data to the slave by not generating an acknowledge bit on the last byte that has been clocked

out of the slave. In this case, the slave must leave the data line HIGH to enable the master to generate

the STOP condition.

DS1307 64 x 8, Serial, I2C Real-Time Clock

11 of 15

Figure 4. Data Transfer on I2C Serial Bus

Depending upon the state of the R/W bit, two types of data transfer are possible:

1. Data transfer from a master transmitter to a slave receiver. The first byte transmitted by the

master is the slave address. Next follows a number of data bytes. The slave returns an acknowledge

bit after each received byte. Data is transferred with the most significant bit (MSB) first.

2. Data transfer from a slave transmitter to a master receiver. The first byte (the slave address) is

transmitted by the master. The slave then returns an acknowledge bit. This is followed by the slave

transmitting a number of data bytes. The master returns an acknowledge bit after all received bytes

other than the last byte. At the end of the last received byte, a “not acknowledge” is returned.

The master device generates all the serial clock pulses and the START and STOP conditions. A

transfer is ended with a STOP condition or with a repeated START condition. Since a repeated

START condition is also the beginning of the next serial transfer, the bus will not be released. Data is

transferred with the most significant bit (MSB) first.

The DS1307 may operate in the following two modes:

1. Slave Receiver Mode (Write Mode): Serial data and clock are received through SDA and SCL.

After each byte is received an acknowledge bit is transmitted. START and STOP conditions are

recognized as the beginning and end of a serial transfer. Hardware performs address recognition after

reception of the slave address and direction bit (see Figure 5). The slave address byte is the first byte

received after the master generates the START condition. The slave address byte contains the 7-bit

DS1307 address, which is 1101000, followed by the direction bit (R/W), which for a write is 0. After

receiving and decoding the slave address byte, the DS1307 outputs an acknowledge on SDA. After

the DS1307 acknowledges the slave address + write bit, the master transmits a word address to the

DS1307. This sets the register pointer on the DS1307, with the DS1307 acknowledging the transfer.

The master can then transmit zero or more bytes of data with the DS1307 acknowledging each byte

received. The register pointer automatically increments after each data byte are written. The master

will generate a STOP condition to terminate the data write.

ACKNOWLEDGEMENT

SIGNAL FROM RECEIVER

ACKNOWLEDGEMENT

SIGNAL FROM RECEIVER

DIRECTION

BIT

REPEATED IF MORE BYTES

ARE TRANSFERED

START

CONDITION STOP

CONDITION

REPEATED

START

CONDITION

MSB

1 2 6 7 8 9 1 2 3-7 8 9

ACK

SDA

SCL

DS1307 64 x 8, Serial, I2C Real-Time Clock

12 of 15

Figure 5. Data Write—Slave Receiver Mode

2. Slave Transmitter Mode (Read Mode): The first byte is received and handled as in the slave

receiver mode. However, in this mode, the direction bit will indicate that the transfer direction is

reversed. The DS1307 transmits serial data on SDA while the serial clock is input on SCL. START

and STOP conditions are recognized as the beginning and end of a serial transfer (see Figure 6). The

slave address byte is the first byte received after the START condition is generated by the master. The

slave address byte contains the 7-bit DS1307 address, which is 1101000, followed by the direction bit

(R/W), which is 1 for a read. After receiving and decoding the slave address the DS1307 outputs an

acknowledge on SDA. The DS1307 then begins to transmit data starting with the register address

pointed to by the register pointer. If the register pointer is not written to before the initiation of a read

mode the first address that is read is the last one stored in the register pointer. The register pointer

automatically increments after each byte are read. The DS1307 must receive a Not Acknowledge to

end a read.

Figure 6. Data Read—Slave Transmitter Mode

XXXXXXX

1101000 S 0 XXXXXXX

XXXXXXX

<RW>

S — START

— ACKNOWLEDGE

P — STOP

R/W — READ/WRITE OR DIRECTION BIT ADDRESS = D0H

DATA TRANSFERRED

(X+1 BYTES + ACKNOWLEDGE)

XXXXXXX

1101000 S 1 XXXXXXX

XXXXXXX

<RW>

DATA TRANSFERRED

(X+1 BYTES + ACKNOWLEDGE); NOTE: LAST DATA BYTE IS

FOLLOWED BY A NOT ACKNOWLEDGE (A) SIGNAL)

S — START

— ACKNOWLEDGE

P — STOP

— NOT ACKNOWLEDGE

— READ/WRITE OR DIRECTION BIT ADDRESS = D1H

DS1307 64 x 8, Serial, I2C Real-Time Clock

13 of 15

TYPICAL OPERATING CIRCUIT

PIN CONFIGURATIONS

DS1307

CPU

VCC

1 2

SDA

SCL

GND

X2 X1

VCC

RPU RPU

CRYSTAL

FT/OUT

VBAT

RPU = tr / Cb

TOP VIEW

PDIP (300 mils)

VBAT

GND

VCC

SQW/OUT

SCL

5SDA

SO (150 mils)

VBAT

GND

VCC

SQW/OUT

SCL

SDA

DS1307

DS1307 64 x 8, Serial, I2C Real-Time Clock

14 of 15

PACKAGE INFORMATION

(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package

outline information, go to www.maxim-ic.com/DallasPackInfo.)

DS1307 64 x 8, Serial, I2C Real-Time Clock

15 of 15

Maxim/Dallas Semiconductor cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim/Dallas Semiconductor product.

No circuit patent licenses are implied. Maxim/Dallas Semiconductor reserves the right to change the circuitry and specifications without notice at any time.

Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600

The Maxim logo is a registered trademark of Maxim Integrated Products, Inc. The Dallas logo is a registered trademark of Dallas Semiconductor Corporation.

PACKAGE INFORMATION (continued)

(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package

outline information, go to www.maxim-ic.com/DallasPackInfo.)