Solid State Relays G3PA 437
Solid State Relays
G3PA
Extremely Thin Relays Integrated with Heat Sinks
• Downsizing achieved through optimum design of heat sink.
• Mounting possible via screws or via DIN track.
• Close mounting possible for linking terminals. (Except for
G3PA-260B-VD and G3PA-450B-VD-2.)
• Applicable with 3-phase loads.
• Replaceable power element cartridges.
• Complies with VDE 0160 (finger protection), with a dielec-
tric strength of 4,000 V between input and load.
• Complies with VDE 0805, IEC 950.
• Certified by UL, CSA, and VDE (reinforced insulation).
Ordering Information
List of Models
To Order: Select the part number and add the rated input voltage range. (e.g., G3PA-430B-VD-2 DC12-24)
Isolation Zero cross function Indicator Rated output load Rated input voltage Model
Phototriac
coupler
Yes Yes 10 A at 24 to 240 VAC 5 to 24 VDC G3PA-210B-VD
20 A at 24 to 240 VAC G3PA-220B-VD
40 A at 24 to 240 VAC G3PA-240B-VD
60 A at 24 to 240 VAC G3PA-260B-VD
No 10 A at 24 to 240 VAC G3PA-210BL-VD
20 A at 24 to 240 VAC G3PA-220BL-VD
40 A at 24 to 240 VAC G3PA-240BL-VD
60 A at 24 to 240 VAC G3PA-260BL-VD
Yes 10 A at 24 to 240 VAC 24 VAC G3PA-210B-VD
20 A at 24 to 240 VAC G3PA-220B-VD
40 A at 24 to 240 VAC G3PA-240B-VD
60 A at 24 to 240 VAC G3PA-260B-VD
20 A at 180 to 400 VAC 12 to 24 VDC G3PA-420B-VD
30 A at 180 to 400 VAC G3PA-430B-VD
20 A at 200 to 480 VAC G3PA-420B-VD-2
30 A at 200 to 480 VAC G3PA-430B-VD-2
50 A at 200 to 480 VAC G3PA-450B-VD-2
438 Solid State Relays G3PA
Replacement Parts
Specifications
■Ratings (at an Ambient Temperature of 25°C)
Input
Output
Refer to Engineering Data for further details.
Name Carry current Load voltage range Applicable SSR Model VDE
certification
Power Device
Cartridge
10 A 19 to 264 VAC G3PA-210B-VD DC5-24 G32A-A10-VD DC5-24 Yes
G3PA-210BL-VD DC5-24 G32A-A10L-VD DC5-24
G3PA-210B-VD AC24 G32A-A10-VD AC24
20 A G3PA-220B-VD DC5-24 G32A-A20-VD DC5-24
G3PA-220BL-VD DC5-24 G32A-A20L-VD DC5-24
G3PA-220B-VD AC24 G32A-A20-VD AC24
40 A G3PA-240B-VD DC5-24 G32A-A40-VD DC5-24
G3PA-240BL-VD DC5-24 G32A-A40L-VD DC5-24
G3PA-240B-VD AC24 G32A-A40-VD AC24
60 A G3PA-260B-VD DC5-24 G32A-A60-VD DC5-24
G3PA-260BL-VD DC5-24 G32A-A60L-VD DC5-24
G3PA-260B-VD AC24 G32A-A60-VD AC24
20 A 150 to 440 VAC G3PA-420B-VD DC12-24 G32A-A420-VD DC12-24
30 A G3PA-430B-VD DC12-24 G32A-A430-VD DC12-24
20 A 180 to 528 VAC G3PA-420B-VD-2 DC12-24 G32A-A420-VD-2 DC12-24
30 A G3PA-430B-VD-2 DC12-24 G32A-A430-VD-2 DC12-24
50 A G3PA-450B-VD-2 DC12-24 G32A-A450-VD-2 DC12-24
Model Rated voltage Operating Voltage
range
Input current
impedance
Voltage level
Must operate voltage Must release voltage
G3PA-2❏❏B-VD 5 to 24 VDC 4 to 30 VDC 7 mA max. 4 VDC max. 1 VDC min.
G3PA-2❏❏BL-VD 20 mA max.
G3PA-2❏❏B-VD 24 VAC 19.2 to 26.4 VAC 1.4 kΩ±20% 19.2 VAC max. 4.8 VAC min.
G3PA-4❏❏B-VD(-2) 12 to 24 VDC 9.6 to 30 VDC 7 mA max. 9.2 VDC max. 1 VDC min.
Model Applicable load
Rated load voltage Load voltage range Load current Inrush current
G3PA-210B(L)-VD 24 to 240 VAC (50/60 Hz) 19 to 264 VAC (50/60 Hz) 0.1 to 10 A 150 A (60 Hz, 1 cycle)
G3PA-220B(L)-VD 0.1 to 20 A 220 A (60 Hz, 1 cycle)
G3PA-240B(L)-VD 0.5 to 40 A 440 A (60 Hz, 1 cycle)
G3PA-260B(L)-VD 0.5 to 60 A 440 A (60 Hz, 1 cycle)
G3PA-420B-VD 180 to 400 VAC (50/60 Hz) 150 to 440 VAC (50/60 Hz) 0.5 to 20 A 220 A (60 Hz, 1 cycle)
G3PA-430B-VD 0.5 to 30 A 440 A (60 Hz, 1 cycle)
G3PA-420B-VD-2 200 to 480 VAC (50/60 Hz) 180 to 528 VAC (50/60 Hz) 0.5 to 20 A 220 A (60 Hz, 1 cycle)
G3PA-430B-VD-2 0.5 to 30 A 440 A (60 Hz, 1 cycle)
G3PA-450B-VD-2 0.5 to 50 A 440 A (60 Hz, 1 cycle)
Solid State Relays G3PA 439
■Characteristics
Item G3PA-
210B(L)-VD
G3PA-
220B(L)-VD
G3PA-
240B(L)-VD
G3PA-
260B(L)-VD
G3PA-
420B-VD
G3PA-
420B-VD-2
G3PA-
430B-VD
G3PA-
430B-VD-2
G3PA-
450B-VD-2
Operate time 1/2 of load power source cycle + 1 ms max. (DC Input, -B models)
1 1/2 of load power source cycle + 1 ms max. (AC Input)
1 ms max. (-BL models)
Release time 1/2 of load power source cycle + 1 ms max. (DC Input)
1 1/2 of load power source cycle + 1 ms max. (AC Input)
Output ON
voltage drop
1.6 V (RMS) max. 1.8 V (RMS) max.
Leakage
current
5 mA max. (at 100 VAC)
10 mA max. (at 200 VAC)
10 mA max. (at 100 VAC)
20 mA max. (at 200 VAC)
20 mA
max. (at
400 VAC)
20 mA max. (at
480 VAC)
20 mA
max. (at
400 VAC)
20 mA max. (at 480 VAC)
I2t 260 A2s 1,260 A2s 260 A2s 1,800 A2s 1,800 A2s 1,800 A2s
Insulation
resistance
100 MΩ min. (at 500 VDC)
Dielectric
strength
4,000 VAC, 50/60 Hz for 1 min
Vibration
resistance
Malfunction: 10 to 55, 0.75–mm double amplitude (Mounted to DIN track)
Shock
resistance Malfunction: 300 m/s2 (mounted to DIN track)
Ambient
temperature
Operating:–30°C to 80°C (with no icing or condensation)
Storage:–30°C to 100°C (with no icing or condensation)
Certified
standards
UL, CSA, EN60950 File No. 5915ÜG UL, CSA ,
EN60947-
4-3 File
No.
6642ÜG
UL, CSA,
EN60947-4-3
File No.
133127ÜG
UL, CSA,
EN60947-
4-3 File
No.
6642ÜG
UL, CSA, EN60947-4-3 File
No. 133127ÜG
Ambient
humidity
Operating: 45% to 85%
Weight Approx.
260 g
Approx.
340 g
Approx.
460 g
Approx.
900 g
Approx.
290 g
Approx.
290 g
Approx.
410 g
Approx.
410 g
Approx.
900 g
440 Solid State Relays G3PA
Operation
■Replacement Parts
G32A-A Power Device Cartridge
The G32A-A Power Device Cartridge (a Triac Unit) can be replaced with a new one. When the temperature indicator has changed from pink to red,
the triac circuitry may have malfunctioned possibly by an excessive flow of current, in which case, dismount the damaged cartridge for replacement.
The damaged cartridge can be replaced with a new one without disconnecting the wires from the G3PA.
Improve the heat radiation efficiency of the G3PA before replacing the cartridge.
The G32A-A Power Device Cartridge can withstand an excessive current for a short period of time, such as may be caused accidentally by the
short circuitry of the load, in which case the temperature indicator will not turn red.
Be sure to turn OFF the power supply when replacing the Cartridge. Supplying power with the Cartridge removed may result in malfunction.
Appearance
Replacing Power Device Cartridges
When replacing Power Device Cartridges, use the specified model. Using a Power Device Cartridge other than the specified one will result in faulty
operation and destruction of the elements.
G32A-A10(L)-VD G32A-A20(L)-VD G32A-A40(L)-VD G32A-A60(L)-VD
G32A-A420-VD(-2) G32A-A430-VD(-2) G32A-A450-VD-2
Solid State Relays G3PA 441
■Replacement Procedure
G32A-A10(L)-VD/G32A-A20(L)-VD/G32-A420-VD(-2)
Use the special tool (provided) to extract the cartridge for replacement with a new one.
Extraction
Follow the procedures below to remove the Power Device Cartridge
from the G3PA.
1. Switch off the power.
2. Remove the terminal cover.
3. Hook the indented part of the cartridge with the tool (supplied with
a new cartridge) and pull up on the cartridge to remove it.
Installation
Follow the procedures below to Install the Power Device Cartridge on
the G3PA.
1. Apply silicone grease (provided with the G32A-A) to the entire
surface of the heat sink.
2. Make sure that there is no dust or pieces of wire on the heat sink
of the G32A-A or the G3PA.
3. Insert the cartridge into the opening of the G3PA so that the let-
ters on the cartridge and those on the G3PA are in the same
direction and side A and side B are even.
4. Attach the terminal cover.
5. Switch on the power and check the G3PA to be sure it works
properly.
G32A-A40(L)-VD/G32A-A60(L)-VD/G32A-A430-VD(-2)/G32A-A450-VD-2
The G32A Power Device Cartridge is mounted and secured with screws to the G3PA Unit.
Extraction
Follow the procedures below to remove the G32A-A Power Device
Cartridge from the G3PA.
1. Switch off the power.
2. Remove the terminal cover.
3. Loosen the two centered screws on the sides to dismount the car-
tridge. The screws are connected to terminals 1 and 2.
4. Loosen the screws on both the corners.
5. Hold the indented part of both the corners to remove
the cartridge.
Installation
Follow the procedures below to Install the Power Device Cartridge on
the G3PA.
1. Apply silicone grease to the entire surface of the heat sink.
2. Make sure that there is no dust or pieces of wire on the heat sink
of the G32A-A or the G3PA.
Remover
Hook here with
Remover.
Apply silicone grease here.
Side A
Side B
Loosen
Loosen
Loosen
Loosen
Apply silicone grease here.
442 Solid State Relays G3PA
3. Insert the cartridge into the opening of the G3PA so that side A
and side B are even.
4. Tighten the screws on both the corners with a tightening torque of
0.59 to 0.78 N•m.
5. Tighten the screws on both the sides with a tightening torque of
0.59 to 0.78 N•m.
6. Attach the terminal cover.
7. Switch on the power and check the G3PA to be sure it works
properly.
■Linking Terminal Connection
•Connecting with linking terminal for G3PA-210B(L)-VD, -220B(L)-
VD, -240B(L)-VD and G3PA-420B-VD(-2), G3PA-430B-VD(-2).
•Connecting with linking terminal to “G32A-D” series short circuit
unit. (Order short circuit units seperately.)
Side B
Side A
SSR1 SSR2 SSR1 SSR2
1. When SSRs are close
mounted, loosen the
M3.5 Sems screw and
flip the linking terminal
down.
2. Insert the linking
terminal securely
into the center of
the screw and
tighten the screw.
*
SSR G32A Unit SSR G32A Unit
* The cover will not fit if
the terminal protrudes.
1. When SSR are close
mounted, loosen the
M3.5 Sems screw on
the G32A and flip the
linking terminal down.
2. Insert the linking terminal
securely into the center
of the screw and tighten
the screw. Ensure that
the linking terminal does
not protrude.
Linking terminal
Linking terminal
Connect the terminal with power off.
G3PA-420B-VD
Refer to the instruction manual for
the G32A-A Power Device Cartridge
to replace the G3PA's triac part.
When the temperature indicator has turned from pink to red, the G32-A-A Power Device Cartridge
may have malfunctioned, in which case the cartridge must be replaced with a new one.
Use the terminal cover to prevent accidents
due to electric shock.
Linking
terminal
Linking
terminal
Solid State Relays G3PA 443
Engineering Data
Load Current vs. Ambient Temperature
Note: Close mounting is possible for a maximum of three Units by reducing the load current by 20%. (A minimum clearance of 10 mm must be
provided when mounting four or more Units.)
25
15
40 60 80 100200-20-30
60
40
25
20
80
Panel Ground
Ambient temperature (°C) Ambient temperature (°C) Ambient temperature (°C)
Load current (A)
Load current (A)
Load current (A)
Vertical Mounting
G3PA-240B(L)-VD G3PA-260B(L)-VD
G3PA-220B(L)-VD
G3PA-210B(L)-VD
G3PA-210B(L)-VD, G3PA-220B(L)-VD
Ambient temperature (°C) Ambient temperature (°C)
Load current (A)
Load current (A)
G3PA-430B-VD, G3PA-430B-VD-2G3PA-420B-VD, G3PA-420B-VD-2 G3PA-450B-VD-2
Ambient temperature (°C)
Load current (A)
444 Solid State Relays G3PA
Input Voltage vs. Input Current
G3PA-2@0B-VD
Input current (mA)
Input voltage (V)
Input current (mA)
Input voltage (V)
G3PA-4@0-VD, G3PA-4@-VD-2
40201086421
0.1
0.2
0.4
0.6
0.8
1
2
4
6
8
Input impedance
Input current
Ta = 25°C
40201086421
0.1
0.2
0.4
2
4
6
8
10
1
0.6
0.8
Input impedance
Input
current
T = 25°C
Input impedance (kΩ)
Input impedance (kΩ)
40 60 80 10
0
200−20−30
60
40
42
20
3.5
11
28
15
11
14
18
20
10
5
5.5 10
7
Panel
Ground
Horizontal Mounting
Ambient temperature (°C) Ambient temperature (°C) Ambient temperature (°C)
Load current (A)
Load current (A)
Load current (A)
G3PA-240B(L)-VD G3PA-260B(L)-VD
G3PA-220B(L)-VD
G3PA-210B(L)-VD, G3PA-220B(L)-VD
G3PA-210B(L)-VD
Solid State Relays G3PA 445
40
30
24
20
10
−30 10 30 80
30
20
16
10
−30 10 30 80 100
40 60 80 100200-20-30
64
40
48
20
18
4.5
36
15
13
20
30
5
7
40
45
30
20
10
14
9
27
Ambient temperature (°C)
G3PA-430B-VD, G3PA-430B-VD-2
Load current (A)
Ambient temperature (°C)
Load current (A)
G3PA-420B-VD, G3PA-420B-VD-2
DIN track
Panel Ground
Close Mounting (Up to Three)
Ambient temperature (°C) Ambient temperature (°C) Ambient temperature (°C)
Load current (A)
Load current (A)
Load current (A)
G3PA-240B(L)-VD G3PA-260B(L)-VD
G3PA-220B-VD
G3PA-210B-VD
G3PA-210B(L)-VD, G3PA-220B(L)-VD
G3PA-450B-VD-2
Ambient temperature (°C)
Load current (A)
446 Solid State Relays G3PA
Inrush Current Resistivity
One cycle, non-repetitive (Keep the inrush current to half the rated value if it occurs repetitively.)
G3PA-210B(L)-VD G3PA-220B(L)-VD, G3PA-420B-VD,
G3PA-420B-VD-2
G3PA-240B(L)-VD/260B(L)-VD,
G3PA-430B-VD, G3PA-430B-VD-2,
G3PA-450B-VD-2
Inrush current (A. Peak)
Energized time (ms)
Inrush current (A. Peak)
Energized time (ms)
Inrush current (A. Peak)
Energized time (ms)
Solid State Relays G3PA 447
Dimensions
Note: All units are in millimeters unless otherwise indicated.
Two, 4.5 dia. or M4 holes
4.6 dia.
Two, M 4
100 max.
G3PA-210B(L)-VD
Mounting
Holes
Without Terminal
Cover
With Terminal
Cover
Linking terminal B1
Linking
terminal B2
Tw o,
M3.5
4.6 x 5.6 elliptical
hole
Terminal
Arrangement/
Internal Connections
Tri gger circuit
Input circuit
Two, 4.5 dia. or M4 holes
4.6 dia.
Two, M 4
100 max.
G3PA-220B(L)-VD
Mounting
Holes
Without Terminal
Cover With Terminal
Cover
Linking terminal B1
Tw o,
M3.5
Linking terminal B2
4.6 x 5.6 elliptical
hole
Terminal
Arrangement/
Internal Connections
Tri gger circuit
Input circuit
4.6 dia.
Two, M 5
100 max.
Two, 4.5 dia. or M4 holes
G3PA-240B(L)-VD
Mounting
Holes
Without Terminal
Cover
With Terminal
Cover
Linking
terminal B1
Tw o,
M3.5
Linking
terminal B2
4.6 x 5.6 elliptical
hole
Terminal
Arrangement/
Internal Connections
Tri gger circuit
Input circuit
448 Solid State Relays G3PA
Two, 4.5 dia. or M4 holes
4.6 dia. Tw o, M5
100 max.
Two, M3.5
110 max.
Mounting Holes
With Terminal
Cover Without Terminal
Cover
G3PA-260B(L)-VD
G3PA-450B-VD-2
4.6 x 5.6
elliptical hole
Terminal Arrangement/
Internal Connections
Tri gger circuit
Input circuit
4.5
7.6
2.2
8.8
13.2
8.6
90±0.2
25±0.2
90±0.3
90 91
67 38 80
Two, M4
Two, M3.5
4.6 dia.
37 max.
4.5 x 5.6 elliptic hole 100 max.
G3PA-420B-VD, G3PA-420B-VD-2
Mounting Holes Terminal Arrangement/
Internal Connections
Tri gger circuit
Input circuit
100
max.
Linking
terminal
−B2
Linking
terminal
+B1
Two, 4.5 dia. or M4
Without Terminal
Cover
With Terminal
Cover
89 91
4.5
13
18
13
7.6
35±0.2 35±0.3
90±0.3
67 38 80
90±0.2
4.6 dia.
100 max.
47 max.
4.6 x 5.6
elliptic hole
G3PA-430B-VD, G3PA-430B-VD-2
Mounting Holes
Two, 4.5 dia. or M4
Two, M5
Terminal Arrangement/
Internal Connections
Tri gger circuit
Input circuit
Linking
terminal
+B1
Linking
terminal
−B2
100
max.
Without Terminal
Cover
With Terminal
Cover
Solid State Relays G3PA 449
Safety Precautions
■Precautions for Correct Use
Please observe the following precautions to prevent failure to oper-
ate, malfunction, or undesirable effect on product performance.
Load Connection
For an AC load, use a power supply rated at 50 or 60 Hz.
The maximum operating frequency is 10 Hz.
The G3PA-(VD) has a built-in varistor for overvoltage protection.
At a low applied voltage, such as 24 VAC, the load current is not fully
supplied. When the Unit is switched ON, the voltage required to
power the Unit deprives the output signal of the necessary voltage
level and thus creates loss time. The lower the load voltage is, the
greater the loss time is. This condition, however, will not create any
serious problems.
For a DC or L load, a diode should be connected in parallel the load
to absorb the counter electromotive force of the load.
Noise Terminal Voltage according to
EN55011
The G3PA-(VD) complies with EN55011 standards when a capacitor
is connected to the load power supply as shown in the following cir-
cuit diagram.
Recommended Capacitor: 1 μF, 250 VAC
Mounting
When attaching a heat sink to the G3PA-(VD), in order to facilitate heat dissipation, apply silicone grease or equivalent heat-conductive grease on
the heat sink. (Toshiba Silicone, Shinetsu Silicone, etc.)
Tighten the mounting screws of the heat sink with a torque of 0.78 to 0.98 N•m.
Loss time
SSR
Input
Load Load power
supply
G3PA-(VD) Output
Load
Input
DIN track
G3PA
G3PA
Panel
DIN track
Panel
The rated ambient
temperature is
40°C. (30°C for
400 V.)
Vertical mounting
Close mounting
Horizontal mounting
• Screw or DIN track
mounting is possible.
• Vertical mounting should
usually be used.
• Close mounting is also
possible.
• Close mounting is possible for
up to 3 G3PA SSRs. (If there
are 4 or more SSRs, mount at
intervals of 10 mm min.)
Reduce the load current by
10% for G3PA-210B-VD,
-220B-VD, -240B-VD and by
20% for G3PA-260B-VD, -
420B-VD(-2), -430B-VD(-2),
-450B-VD-2.
• Leave a distance of 80 mm
• With vertical mounting,
reduce the load current by
30%. (Refer to the Load
Current vs. Ambient
Temperature graph.)
80 mm
Note: Leave a distance of 60 mm min. between SSRs and ducts (especially above the SSR).
↔
↔
↔
Vertical
Vertical
Vertical
450 Solid State Relays G3PA
Close Mounting
SSR Mounting Pitch
Panel Mounting
(At a rated ambient temperature of 40°C).
Relationship between SSRs and Ducts
Ventilation
If the air inlet or air outlet has a filter, clean the filter regularly to pre-
vent it from clogging and ensure an efficient flow of air.
Do not locate any objects around the air inlet or air outlet, otherwise
the objects may obstruct the proper ventilation of the control panel.
A heat exchanger, if used, should be located in front of the SSR Units
to ensure the efficiency of the heat exchanger.
Please reduce the ambient temperature of SSRs.
The rated load current of an SSR is measured at an ambient
temperature of 25 or 40°C.
An SSR uses a semiconductor in the output element. This causes
the temperature inside the control panel to increase due to heating
resulting from the passage of electrical current through the load. To
restrict heating, attach a fan to the ventilation outlet or air inlet of the
control panel to ventilate the panel. This will reduce the ambient tem-
perature of the SSRs and thus increase reliability. (Generally, each
10°C reduction in temperature will double the expected life.)
Example: For 10 SSRs with load currents of 20 A,
0.31 x 10 = 3.1
Thus, 4 fans would be required.
Size of fans: 92 mm2, Air volume: 0.7 m3/min,
Ambient temperature of control panel: 30°C
If there are instruments that generate heat in the control panel
other than SSRs, additional ventilation will be required.
SSR
Between duct
or airflow
obstruction
and SSR
60 mm min.
Mounting direction
Vertical direction
Space between
SSRs
30 mm min.
80 mm min.
min.
Close Mounting
Duct or airflow obstruction
G3PA
G3PA
G3PA
Mounting surface
Mounting surface
Mounting surface
Duct or
airflow
obstruction
Duct or
airflow
obstruction
Vertical
direction
Airflow
(A height of no
more than half
the SSR's height is
recommended.)
Duct Height
If the ducts cannot be
shortened, place the SSR
on a metal base so that it
is not surrounded by the
ducts.
Use short ducts.
Do not surround the SSR
with ducts, otherwise the
heat radiation of the SSR
will be adversely affected.
Countermeasure (1) Countermeasure (2)
50 mm max.
G3PA G3PA
G3PA
Air inlet
Be aware of air flow
Duct or
air flow
obstruction
Ventilation
outlet
Load current (A) 10 A 20 A 30 A 40 A 60 A
Required number of fans
per SSR
0.16 0.31 0.47 0.62 0.93
Solid State Relays G3PA
Omron Electronic Components, LLC
Terms and Conditions of Sales
1. Definitions: The words used herein are defined as follows.
(a) Terms: These terms and conditions
(b) Seller: Omron Electronic Components LLC and its subsidiaries
(c) Buyer: The buyer of Products, including any end user in section III through VI
(d) Products: Products and/or services of Seller
(e) Including: Including without limitation
2. Offer; Acceptance: These Terms are deemed part of all quotations, acknowledgments,
invoices, purchase orders and other documents, whether electronic or in writing, relating
to the sale of Products by Seller. Seller hereby objects to any Terms proposed in Buyer's
purchase order or other documents which are inconsistent with, or in addition to, these
Ter ms.
3. Distributor: Any distributor shall inform its customer of the contents after and including
section III of these Terms.
1. Prices; Payment: All prices stated are current, subject to change without notice by Seller.
Buyer agrees to pay the price in effect at the time the purchase order is accepted by
Seller. Payments for Products received are due net 30 days unless otherwise stated in
the invoice. Buyer shall have no right to set off any amounts against the amount owing in
respect of this invoice.
2. Discounts: Cash discounts, if any, will apply only on the net amount of invoices sent to
Buyer after deducting transportation charges, taxes and duties, and will be allowed only
if (a) the invoice is paid according to Seller's payment terms and (b) Buyer has no past
due amounts owing to Seller.
3. Interest: Seller, at its option, may charge Buyer 1.5% interest per month or the maximum
legal rate, whichever is less, on any balance not paid within the stated terms.
4. Orders: Seller will accept no order less than 200 U.S. dollars net billing.
5. Currencies: If the prices quoted herein are in a currency other than U.S. dollars, Buyer
shall make remittance to Seller at the then current exchange rate most favorable to
Seller; provided that if remittance is not made when due, Buyer will convert the amount
to U.S. dollars at the then current exchange rate most favorable to Seller available
during the period between the due date and the date remittance is actually made.
6. Governmental Approvals: Buyer shall be responsible for all costs involved in obtaining
any government approvals regarding the importation or sale of the Products.
7. Taxes: All taxes, duties and other governmental charges (other than general real
property and income taxes), including any interest or penalties thereon, imposed directly
or indirectly on Seller or required to be collected directly or indirectly by Seller for the
manufacture, production, sale, delivery, importation, consumption or use of the Products
sold hereunder (including customs duties and sales, excise, use, turnover and license
taxes) shall be charged to and remitted by Buyer to Seller.
8. Financial: If the financial position of Buyer at any time becomes unsatisfactory to Seller,
Seller reserves the right to stop shipments or require satisfactory security or payment in
advance. If Buyer fails to make payment or otherwise comply with these Terms or any
related agreement, Seller may (without liability and in addition to other remedies) cancel
any unshipped portion of Products sold hereunder and stop any Products in transit until
Buyer pays all amounts, including amounts payable hereunder, whether or not then due,
which are owing to it by Buyer. Buyer shall in any event remain liable for all unpaid
accounts.
9. Cancellation; Etc: Orders are not subject to rescheduling or cancellation unless Buyer
indemnifies Seller fully against all costs or expenses arising in connection therewith.
10. Force Majeure: Seller shall not be liable for any delay or failure in delivery resulting from
causes beyond its control, including earthquakes, fires, floods, strikes or other labor
disputes, shortage of labor or materials, accidents to machinery, acts of sabotage, riots,
delay in or lack of transportation or the requirements of any government authority.
11. Shipping; Delivery: Unless otherwise expressly agreed in writing by Seller:
(a) All sales and shipments of Products shall be FOB shipping point (unless otherwise
stated in writing by Seller), at which point title to and all risk of loss of the Products
shall pass from Seller to Buyer, provided that Seller shall retain a security interest in
the Products until the full purchase price is paid by Buyer;
(b) Delivery and shipping dates are estimates only; and
(c) Seller will package Products as it deems proper for protection against normal
handling and extra charges apply to special conditions.
12. Claims: Any claim by Buyer against Seller for shortage or damage to the Products
occurring before delivery to the carrier or any claim related to pricing or other charges
must be presented in detail in writing to Seller within 30 days of receipt of shipment.
1. Suitability: IT IS THE BUYER’S SOLE RESPOINSIBILITY TO ENSURE THAT ANY
OMRON PRODUCT IS FIT AND SUFFICIENT FOR USE IN A MOTORIZED VEHICLE
APPLICATION. BUYER SHALL BE SOLELY RESPONSIBLE FOR DETERMINING
APPROPRIATENESS OF THE PARTICULAR PRODUCT WITH RESPECT TO THE
BUYER’S APPLICATION INCLUDING (A) ELECTRICAL OR ELECTRONIC
COMPONENTS, (B) CIRCUITS, (C) SYSTEM ASSEMBLIES, (D) END PRODUCT, (E)
SYSTEM, (F) MATERIALS OR SUBSTANCES OR (G) OPERATING ENVIRONMENT.
Buyer acknowledges that it alone has determined that the Products will meet their
requirements of the intended use in all cases. Buyer must know and observe all
prohibitions of use applicable to the Product/s.
2. Use with Attention: The followings are some examples of applications for which
particular attention must be given. This is not intended to be an exhaustive list of all
possible use of any Product, nor to imply that any use listed may be suitable for any
Product:
(a) Outdoor use, use involving potential chemical contamination or electrical
interference.
(b) Use in consumer Products or any use in significant quantities.
(c) Energy control systems, combustion systems, railroad systems, aviation systems,
medical equipment, amusement machines, vehicles, safety equipment, and
installations subject to separate industry or government regulations.
(d) Systems, machines, and equipment that could present a risk to life or property.
3. Prohibited Use: NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING
SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM
AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE
PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE
WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
4. Motorized Vehicle Application: USE OF ANY PRODUCT/S FOR A MOTORIZED
VEHICLE APPLICATION MUST BE EXPRESSLY STATED IN THE SPECIFICATION BY
SELLER.
5. Programmable Products: Seller shall not be responsible for the Buyer's programming of
a programmable Product.
1. Warranty: Seller's exclusive warranty is that the Products will be free from defects in
materials and workmanship for a period of twelve months from the date of sale by Seller
(or such other period expressed in writing by Seller). SELLER MAKES NO WARRANTY
OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT ALL OTHER WARRANTIES,
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE OF THE PRODUCTS.
2. Buyer Remedy: Seller's sole obligation hereunder shall be to replace (in the form
originally shipped with Buyer responsible for labor charges for removal or replacement
thereof) the non-complying Product or, at Seller's election, to repay or credit Buyer an
amount equal to the purchase price of the Product; provided that there shall be no
liability for Seller or its affiliates unless Seller's analysis confirms that the Products were
correctly handled, stored, installed and maintained and not subject to contamination,
abuse, misuse or inappropriate modification. Return of any Products by Buyer must be
approved in writing by Seller before shipment.
3. Limitation on Liability: SELLER AND ITS AFFILIATES SHALL NOT BE LIABLE FOR
SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF
PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED
WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT,
WARRANTY, NEGLIGENCE OR STRICT LIABILITY. FURTHER, IN NO EVENT SHALL
LIABILITY OF SELLER OR ITS AFFILITATES EXCEED THE INDIVIDUAL PRICE OF
THE PRODUCT ON WHICH LIABILITY IS ASSERTED.
4. Indemnities: Buyer shall indemnify and hold harmless Seller, its affiliates and its
employees from and against all liabilities, losses, claims, costs and expenses (including
attorney's fees and expenses) related to any claim, investigation, litigation or proceeding
(whether or not Seller is a party) which arises or is alleged to arise from Buyer's acts or
omissions under these Terms or in any way with respect to the Products.
1. Intellectual Property: The intellectual property embodied in the Products is the exclusive
property of Seller and its affiliates and Buyer shall not attempt to duplicate it in any way
without the written permission of Seller. Buyer (at its own expense) shall indemnify and
hold harmless Seller and defend or settle any action brought against Seller to the extent
that it is based on a claim that any Product made to Buyer specifications infringed
intellectual property rights of another party.
2. Property; Confidentiality: Notwithstanding any charges to Buyer for engineering or
tooling, all engineering and tooling shall remain the exclusive property of Seller. All
information and materials supplied by Seller to Buyer relating to the Products are
confidential and proprietary, and Buyer shall limit distribution thereof to its trusted
employees and strictly prevent disclosure to any third party.
3. Performance Data: Performance data is provided as a guide in determining suitability
and does not constitute a warranty. It may represent the result of Seller's test conditions,
and the users must correlate it to actual application requirements.
4. Change In Specifications: Product specifications and descriptions may be changed at
any time based on improvements or other reasons. It is Seller’s practice to change part
numbers when published ratings or features are changed, or when significant
engineering changes are made. However, some specifications of the Product may be
changed without any notice.
5. Errors And Omissions: The information on Seller’s website or in other documentation
has been carefully checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
6. Export Controls: Buyer shall comply with all applicable laws, regulations and licenses
regarding (a) export of the Products or information provided by Seller; (b) sale of
Products to forbidden or other proscribed persons or organizations; (c) disclosure to non-
citizens of regulated technology or information.
1. Waiver: No failure or delay by Seller in exercising any right and no course of dealing
between Buyer and Seller shall operate as a waiver of rights by Seller.
2. Assignment: Buyer may not assign its rights hereunder without Seller's written consent.
3. Law: These Terms are governed by Illinois law (without regard to conflict of laws).
Federal and state courts in Cook County, Illinois have exclusive jurisdiction for any
dispute hereunder.
4. Amendment: These Terms constitute the entire agreement between Buyer and Seller
relating to the Products, and no provision may be changed or waived unless in writing
signed by the parties.
5. Severability: If any provision hereof is rendered ineffective or invalid, such provision shall
not invalidate any other provision.
I. GENERAL
II. SALES
III. PRECAUTIONS
IV. WARRANTY AND LIMITATION
V. INFORMATION; ETC.
VI. MISCELLANEOUS
Solid State Relays G3PA
Certain Precautions on Specifications and Use
1. Suitability for Use. Seller shall not be responsible for conformity with any stan-
dards, codes or regulations which apply to the combination of the Product in
Buyer's application or use of the Product. At Buyer's request, Seller will pro-
vide applicable third party certification documents identifying ratings and limi-
tations of use which apply to the Product. This information by itself is not
sufficient for a complete determination of the suitability of the Product in com-
bination with the end product, machine, system, or other application or use.
Buyer shall be solely responsible for determining appropriateness of the par-
ticular Product with respect to Buyer's application, product or system. Buyer
shall take application responsibility in all cases but the following is a non-
exhaustive list of applications for which particular attention must be given:
(i) Outdoor use, uses involving potential chemical contamination or electrical
interference, or conditions or uses not described in this document.
(ii) Energy control systems, combustion systems, railroad systems, aviation
systems, medical equipment, amusement machines, vehicles, safety
equipment, and installations subject to separate industry or government
regulations.
(iii) Use in consumer products or any use in significant quantities.
(iv) Systems, machines and equipment that could present a risk to life or
property. Please know and observe all prohibitions of use applicable to this
product.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS
RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM
AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT
THE OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE
INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
2. Programmable Products. Seller shall not be responsible for the user's pro-
gramming of a programmable product, or any consequence thereof.
3. Performance Data. Performance data given in this publication is provided as
a guide for the user in determining suitability and does not constitute a war-
ranty. It may represent the result of Seller's test conditions, and the users must
correlate it to actual application requirements. Actual performance is subject to
Seller's Warranty and Limitations of Liability.
4. Change in Specifications. Product specifications and accessories may be
changed at any time based on improvements and other reasons. It is our prac-
tice to change part numbers when published ratings or features are changed,
or when significant construction changes are made. However, some specifica-
tions of the Product may be changed without any notice. When in doubt, spe-
cial part numbers may be assigned to fix or establish key specifications for
your application. Please consult with your Seller representative at any time to
confirm actual specifications of purchased Product.
5. Errors and Omissions. The information in this publication has been carefully
checked and is believed to be accurate; however, no responsibility is assumed
for clerical, typographical or proofreading errors, or omissions.
6. RoHS Compliance. Where indicated, our products currently comply, to the
best of our knowledge as of the date of this publication, with the requirements
of the European Union's Directive on the Restriction of certain Hazardous
Substances ("RoHS"), although the requirements of RoHS do not take effect
until July 2006. These requirements may be subject to change. Please consult
our website for current information.
OMRON ON-LINE
Global - http://www.omron.com
USA - http://www.components.omron.com
Cat. No. X301-E-1 Printed in USA
OMRON ELECTRONIC
COMPONENTS LLC
55 E. Commerce Drive, Suite B
Schaumburg, IL 60173
847-882-2288
06/09 Specifications subject to change without notice
Complete “Terms and Conditions of Sale” for product purchase and use are on Omron’s website
at http://www.components.omron.com – under the “About Us” tab, in the Legal Matters section.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.