EAO - Your Expert Partner for Human Machine Interfaces EAO Product Information Series 51 Switches and Indicators 51 Contents 51 Description ...................................................................................................... 3 Product Assembly .......................................................................................... 4 Devices raised mounting ............................................................................... 7 Devices flush mounting ............................................................................... 13 Accessories................................................................................................... 21 Technical Data............................................................................................... 33 Typical Applications ..................................................................................... 36 Application guidelines.................................................................................. 37 Marking .......................................................................................................... 38 Drawings........................................................................................................ 40 Index............................................................................................................... 58 2 01.2010 51 Description Specimen order Product Information General notes The illuminated pushbuttons of series 51 with hoseproof front (IP 65) can be supplied with snap-action or low-level switching elements. The equipment (switches) for raised mounting are protected against accidental operation by the extended sides of the bezel. Flush mounting equipment excells with best available ergonomy and low down hight. To supplement the range of illuminated pushbuttons, we can offer a hoseproof safety keylock switch with various lock numbers. Mounting All switch actuators are mounted from the front by pushing them through the mounting hole in the front panel. They are then fixed from the back with a fixing nut and the mounting tool Typ-Nr. 01-907. Max. tightening torque 50 Ncm. For switching elements we offer plug-in bases, which when soldered to a PCB enable a plug-in connection to the button. The rectangular actuators for raised are provided with an anti-twisting device. 0 Indicator : - Indicator actuator, 18 x 24 mm, soldering terminal 31-040.005 Essential accessories : - Lens plastic blue, transparent, flush, 18 x 24 mm 31-903.6 - Single-LED, T1 3/4 MG, 24 VAC/DC, blau 10-2J12.1066 We reserve the right to modify technical data All dimensions in mm Lenses The flat or concave lenses are available in various colours, as well as translucent or transparent. Round lenses for flush mounting equipment are available in aluminium also. Because of production related reasons, the colours of anodized aluminium parts can vary slightly. Marking For further information about engraving, hot stamping and film inserts see part Marking. Illumination The T1 3/4 Midget Groove incandescent (filament) lamp (6 ... 48 V) ensures perfect illumination of the lenses, which are supplied in various colours. T1 3/4 Midget Groove Single-LED (6, 12, 24, 28, 48 V) are also available in blue, green, red, white or yellow. Luminosity and wave length scattering caused by technologie used in the LED manufacturing processes may lead to visual differences in our products. For supply voltages above 48 V, it is necessary to use a voltage reduction element (external series resistor or transformer). Position indication The status of a maintained action switch can be determinded by the position of the lens. Keylock switch Standard lock (Index D). Standard lock number is 311. If the lock number is not specified, we will supply standard number 311. An additional 134 special locks (Index X) are available on request. Master keys for lock numbers 311 ... 445 may be ordered by quoting Typ-Nr. 31-989.300. Two keys are supplied with each keylock switch. Spare keys (Index D) for standard locks may be ordered by quoting Typ-Nr. 31-989.xxx (please state the lock number). 3 01.2010 51 Product Assembly Indicator round, raised mounting 0 1 2 1 2 3 4 5 6 Lens LED Indicator housing Sealing Front plate Fixing nut 1 2 3 4 5 6 Lens LED Switch housing Sealing Front plate Fixing nut 3 4 5 6 Illuminated pushbutton, raised mounting 0 1 2 3 4 5 6 4 01.2010 51 Product Assembly Keylock switch round, flush mounting 0 1 1 2 3 4 5 6 7 8 Actuator housing Front bezel Sealing Front plate Anti-twist ring Thrust piece Fixing nut Switching element 2 3 4 5 6 7 8 5 01.2010 51 Product Assembly Selector switch square, flush mounting 0 1 2 3 4 5 6 7 8 6 01.2010 1 2 3 4 5 6 7 8 Actuator housing LED Actuator housing Front bezel Sealing Front plate Fixing bracket Fixing nut 51 Devices raised mounting Indicator actuator Essential Accessories: d Lens plastic, raised mounting page 21 d Single-LED page 30 4 4 4 Circuit drawing O 18 mm Typ-Nr. 51-741.006 51-742.006 51-030.005 51-030.002 51-031.006 Technical drawing UT UT S S1 UT a 18 x 24 mm Typ-Nr. 51-701.006 51-702.006 51-040.005 51-040.002 51-041.006 Mounting dimensions 1D 2D - b 18 x 18 mm Typ-Nr. 51-703.006 51-704.006 51-050.005 51-050.002 51-051.006 Component layout IP 65 Terminals Diode (1N 4007) Indicator actuator Front protection Continuation see next page e 1 1 1 1 1 12 12 12 12 12 78 79 1 1 1 0.006 0.006 0.004 0.004 0.005 Indicators fit also in mounting hole no. 2 Diode (1N 4007): D = Diode, - = without Terminals: UT = Universal terminal, S = Soldering terminal, S1 = Soldering terminal (also pluggable 2.8 x 0.5 mm) Component layout from page 40, Mounting dimensions from page 41, Technical drawing from page 42, Circuit drawing from page 47 7 01.2010 51 Devices raised mounting Illuminated pushbutton actuator Essential Accessories: d Lens plastic, raised mounting page 21 d Single-LED page 30 - 1 NO - 2 NC - 2 NO - 1 NC + 1 NO 1D 2D - M 2 NC + 2 NO 1D 2D - 3 NC + 3 NO - 4 NC + 4 NO - MA M MA M MA M MA M MA M Component layout Terminals UT UT UT UT UT UT UT UT UT UT H H H H S S1 S S1 H H H H S S S S S S O 18 mm Typ-Nr. 51-476.036 51-436.036 51-473.036 51-433.036 51-475.036 51-435.036 51-472.036 51-432.036 51-471.036 51-431.036 51-747.0292 51-743.0292 51-748.0292 51-744.0292 51-271.0252 51-271.022 51-131.0252 51-131.022 51-749.0292 51-745.0292 51-750.0292 51-746.0292 51-272.0252 51-132.0252 51-273.0252 51-133.0252 51-274.0252 51-134.0252 4 4 4 4 4 4 4 4 4 4 Circuit drawing 1 NC + 1 NO MA M MA M MA M MA M MA M MA M MA M MA a 18 x 24 mm Typ-Nr. 51-466.036 51-426.036 51-463.036 51-423.036 51-465.036 51-425.036 51-462.036 51-422.036 51-461.036 51-421.036 51-713.0292 51-705.0292 51-714.0292 51-706.0292 51-261.0252 51-261.022 51-121.0252 51-121.022 51-715.0292 51-707.0292 51-716.0292 51-708.0292 51-262.0252 51-122.0252 51-263.0252 51-123.0252 51-264.0252 51-124.0252 Technical drawing - b 18 x 18 mm Typ-Nr. 51-486.036 51-456.036 51-483.036 51-453.036 51-485.036 51-455.036 51-482.036 51-452.036 51-481.036 51-451.036 51-717.0292 51-709.0292 51-718.0292 51-710.0292 51-281.0252 51-281.022 51-151.0252 51-151.022 51-719.0292 51-711.0292 51-720.0292 51-712.0292 51-282.0252 51-152.0252 51-283.0252 51-153.0252 51-284.0252 51-154.0252 Mounting dimensions SA 1 NC Switching action LL Diode (1N 4007) IP 65 Contacts Switching system Illuminated pushbutton actuator Front protection Continuation see next page e 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 11 57 14 60 13 59 12 58 15 61 8 54 9 55 10 7 56 53 4 50 5 51 6 52 3 49 2 48 0.007 0.007 0.007 0.007 0.007 0.007 0.007 0.007 0.007 0.007 0.008 0.008 0.008 0.008 0.006 0.006 0.006 0.006 0.010 0.010 0.010 0.010 0.008 0.008 0.010 0.010 0.012 0.012 Illuminated pushbutton fit also in mounting hole no. 2 Switching system: LL = Low level switching element, SA = Snap-action switching element Contacts: NC = Normally closed, NO = Normally open Diode (1N 4007): - = without, D = Diode Switching action: MA = Maintained action, M = Momentary action Terminals: UT = Universal terminal, H = Combined terminal: Solder-/ Universal (at contact/ at diode), S = Soldering terminal, S1 = Soldering terminal (also pluggable 2.8 x 0.5 mm) Component layout from page 40, Mounting dimensions from page 41, Technical drawing from page 42, Circuit drawing from page 47 8 01.2010 51 Devices raised mounting Keylock switch 2 positions O 18 mm Typ-Nr. 51-415.036D 51-418.036D 51-412.036D 51-414.036D 51-417.036D 51-411.036D 51-235.025D2 51-335.025D2 51-135.025D2 51-235.022D 51-335.022D 51-135.022D 51-236.025D2 51-336.025D2 51-136.025D2 51-237.025D2 51-337.025D2 51-137.025D2 51-238.025D2 51-338.025D2 51-138.025D2 51-438.036D 51-437.036D 51-141.025D2 51-141.022D 51-142.025D2 51-143.025D2 51-144.025D2 4 4 4 4 4 4 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 4 2 4 2 2 2 2 2 2 Circuit drawing a 18 x 24 mm Typ-Nr. 51-405.036D 51-408.036D 51-402.036D 51-404.036D 51-407.036D 51-401.036D 51-295.025D2 51-395.025D2 51-195.025D2 51-295.022D 51-395.022D 51-195.022D 51-296.025D2 51-396.025D2 51-196.025D2 51-297.025D2 51-397.025D2 51-197.025D2 51-298.025D2 51-398.025D2 51-198.025D2 51-428.036D 51-427.036D 51-495.025D2 51-495.022D 51-496.025D2 51-497.025D2 51-498.025D2 Technical drawing IP 65 LL 1 NC + 1 NO MA UT A C C+A 2 NO MA UT A C C+A SA 1 NC + 1 NO MA S A C C+A S1 A C C+A 2 NC + 2 NO MA S A C C+A 3 NC + 3 NO MA S A C C+A 4 NC + 4 NO MA S A C C+A IP 65 LL 1 NC + 1 NO M UT A Position A : Basic position Position C : Momentary action 2 NO M UT A Standard lock 311 SA 1 NC + 1 NO M S A Front : Plastic black S1 A 2 NC + 2 NO M S A 3 NC + 3 NO M S A 4 NC + 4 NO M S A Keylock switch 2 positions Position A : Basic position Position C : Maintained action Standard lock 311 Front : Plastic black b 18 x 18 mm Typ-Nr. 51-445.036D 51-448.036D 51-442.036D 51-444.036D 51-447.036D 51-441.036D 51-255.025D2 51-355.025D2 51-155.025D2 51-255.022D 51-355.022D 51-155.022D 51-256.025D2 51-356.025D2 51-156.025D2 51-257.025D2 51-357.025D2 51-157.025D2 51-258.025D2 51-358.025D2 51-158.025D2 51-458.036D 51-457.036D 51-145.025D2 51-145.022D 51-146.025D2 51-147.025D2 51-148.025D2 Component layout Mounting dimensions Key remove Terminals Switching action Contacts Switching system 0 Front protection Continuation see next page e 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 76 76 76 77 77 77 72 72 72 72 72 72 73 73 73 74 74 74 75 75 75 70 71 66 66 67 68 69 0.017 0.017 0.017 0.017 0.017 0.017 0.016 0.016 0.016 0.016 0.016 0.016 0.016 0.016 0.016 0.016 0.016 0.016 0.016 0.016 0.016 0.017 0.017 0.016 0.016 0.016 0.016 0.016 Other lock numbers on request Switching system: LL = Low level switching element, SA = Snap-action switching element Contacts: NC = Normally closed, NO = Normally open Switching action: MA = Maintained action, M = Momentary action Terminals: UT = Universal terminal, S = Soldering terminal, S1 = Soldering terminal (also pluggable 2.8 x 0.5 mm) Component layout from page 40, Mounting dimensions from page 41, Technical drawing from page 42, Circuit drawing from page 47 9 01.2010 51 Devices raised mounting Keylock switch 3 positions a 18 x 24 mm Typ-Nr. 51-361.022D 51-363.022D 51-362.022D O 18 mm e Typ-Nr. 51-371.022D 2 1 65 0.025 51-373.022D 2 1 65 0.025 51-372.022D 2 1 65 0.025 51-365.022D 51-366.022D 51-375.022D 2 1 64 0.025 51-376.022D 2 1 64 0.025 51-364.022D 51-374.022D 2 1 63 0.025 51-367.022D 51-368.022D 51-377.022D 2 1 62 0.025 51-378.022D 2 1 62 0.025 Other lock numbers on request Switching system: SA = Snap-action switching element Contacts: NC = Normally closed, NO = Normally open Switching action: MA = Maintained action, M = Momentary action Terminals: S1 = Soldering terminal (also pluggable 2.8 x 0.5 mm) Mounting dimensions from page 41, Technical drawing from page 42, Circuit drawing from page 47 10 01.2010 Circuit drawing b 18 x 18 mm Typ-Nr. 51-381.022D Keylock switch 3 positions IP 65 SA 2 NC + 2 NO MA-0-MA S1 A Position C : Maintained action C + B 51-383.022D Position A : Basic position C+A+B 51-382.022D Position B : Maintained action Standard lock 311 51-385.022D Position C : Maintained action IP 65 SA 2 NC + 2 NO MA-0-M S1 A Position A : Basic position C + A 51-386.022D Position B : Momentary action Standard lock 311 S1 A 51-384.022D Position C : Momentary action IP 65 SA 2 NC + 2 NO M-0-M Position A : Basic position Position B : Momentary action Standard lock 311 51-387.022D Position C: Momentary action IP 65 SA 2 NC + 2 NO M-0-MA S1 A Position A : Basic position A + B 51-388.022D Position B : Maintained action standard lock 311 0 Mounting dimensions Technical drawing Key remove Terminals Switching action Contacts Switching system Front protection Continuation see next page 51 Devices raised mounting Selector switch 2 positions illuminative Essential Accessories: d Lever, raised mounting page 24 d Single-LED page 30 SA 2 NC + 2 NO 1D 2D 1D 2D - MA MA MA MA MA M M M M M M M M Position A : Basic position Position C : Momentary action IP 65 LL SA 1D 2D - M M M M M 3 NC + 3 NO 4 NC + 4 NO 1 NC 1 NC + 1 NO 1 NO 2 NC 2 NO 1 NC + 1 NO 2 NC + 2 NO 3 NC + 3 NO 4 NC + 4 NO UT UT UT UT UT H H S S1 H H S S S UT UT UT UT UT H H S S1 H H S S S 4 4 4 4 4 4 4 4 4 4 Circuit drawing MA MA MA MA MA MA MA MA Technical drawing Selector switch 2 positions Position A : Basic position Position C : Maintained action O 18 mm Typ-Nr. 52-476.036 52-473.036 52-475.036 52-472.036 52-471.036 52-747.0292 52-748.0292 52-271.0252 52-271.022 52-749.0292 52-750.0292 52-272.0252 52-273.0252 52-274.0252 52-436.036 52-433.036 52-435.036 52-432.036 52-431.036 52-743.0292 52-744.0292 52-131.0252 52-131.022 52-745.0292 52-746.0292 52-132.0252 52-133.0252 52-134.0252 Mounting dimensions 1D 2D - 0 Component layout 1 NC 1 NC + 1 NO 1 NO 2 NC 2 NO 1 NC + 1 NO Terminals Switching action LL Diode (1N 4007) Switching system IP 65 Contacts Front protection Continuation see next page e 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 43 46 45 44 47 40 41 42 39 36 37 38 35 34 29 32 31 30 33 26 27 28 25 22 23 24 21 20 0.007 0.007 0.007 0.007 0.007 0.008 0.008 0.006 0.006 0.010 0.010 0.006 0.006 0.006 0.007 0.007 0.007 0.007 0.007 0.008 0.008 0.006 0.006 0.010 0.010 0.006 0.006 0.006 Switching system: LL = Low level switching element, SA = Snap-action switching element Contacts: NC = Normally closed, NO = Normally open Diode (1N 4007): - = without, D = Diode Switching action: MA = Maintained action, M = Momentary action Terminals: UT = Universal terminal, H = Combined terminal: Solder-/ Universal (at contact/ at diode), S = Soldering terminal, S1 = Soldering terminal (also pluggable 2.8 x 0.5 mm) Component layout from page 40, Mounting dimensions from page 41, Technical drawing from page 42, Circuit drawing from page 47 11 01.2010 51 Devices raised mounting Selector switch 3 positions illuminative Essential Accessories: d Lever, raised mounting page 24 d Single-LED page 30 Switching action Terminals SA 2 NC + 2 NO MA-0-MA M-0-MA S1 S1 IP 40 SA 2 NC + 2 NO MA-0-M M-0-M S1 S1 52-573.022A 52-572.022A Switching system: SA = Snap-action switching element Contacts: NC = Normally closed, NO = Normally open Switching action: MA = Maintained action, M = Momentary action Terminals: S1 = Soldering terminal (also pluggable 2.8 x 0.5 mm) Mounting dimensions from page 41, Technical drawing from page 42, Circuit drawing from page 47 12 01.2010 Circuit drawing Contacts Selector switch 3 positions Position C : Maintained action Position A : Basic position Position B : Maintained action Position C : Momentary action Position A : Basic position Position B : Momentary action Technical drawing Switching system IP 40 O 18 mm Typ-Nr. 52-571.022A 52-574.022A 0 Mounting dimensions Front protection Continuation see next page e 2 2 6 6 19 17 0.015 0.015 2 2 6 6 18 16 0.015 0.015 51 Devices flush mounting Indicator actuator, flush mounting Actuators usable for front dimensions: b 24 x 24 mm | a 24 x 30 mm | 25 mm dia. Essential Accessories: Front bezel set for Indicators and Illuminated pushbutton, flush mounting page 25 d d d Lens plastic, flush mounting page 21 Single-LED page 30 Circuit drawing Typ-Nr. 51-050.005F 51-050.002F 51-051.006F Technical drawing S S1 UT Mounting dimensions IP 65 Component layout Indicator actuator, flush mounting Terminals Front protection Continuation see next page e 4 3 3 3 15 15 15 1 1 1 0.004 0.004 0.005 Terminals: S = Soldering terminal, S1 = Soldering terminal (also pluggable 2.8 x 0.5 mm), UT = Universal terminal Component layout from page 40, Mounting dimensions from page 41, Technical drawing from page 42, Circuit drawing from page 47 13 01.2010 51 Devices flush mounting Illuminated pushbutton actuator, flush mounting Actuators usable for front dimensions: b 24 x 24 mm | a 24 x 30 mm | 25 mm dia. Essential Accessories: Front bezel set for Indicators and Illuminated pushbutton, flush mounting page 25 d d d Lens plastic, flush mounting page 21 Single-LED page 30 2 NC 2 NO SA 1 NC + 1 NO M 2 NC + 2 NO 3 NC + 3 NO 4 NC + 4 NO MA M MA M MA M Component layout Typ-Nr. 51-486.036F 51-456.036F 51-483.036F 51-453.036F 51-485.036F 51-455.036F 51-482.036F 51-452.036F 51-481.036F 51-451.036F 51-281.0252F 51-281.022F 51-151.0252F 51-151.022F 51-282.0252F 51-152.0252F 51-283.0252F 51-153.0252F 51-284.0252F 51-154.0252F 4 4 4 4 4 4 4 4 4 4 Circuit drawing 1 NO UT UT UT UT UT UT UT UT UT UT S S1 S S1 S S S S S S Technical drawing 1 NC + 1 NO MA M MA M MA M MA M MA M MA Mounting dimensions 1 NC Terminals LL Switching action IP 65 Contacts Switching system Illuminated pushbutton actuator, flush mounting Front protection Continuation see next page e 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 11 57 14 60 13 59 12 58 15 61 10 7 56 53 6 52 3 49 2 48 0.006 0.006 0.006 0.006 0.006 0.006 0.006 0.006 0.006 0.006 0.005 0.007 0.005 0.007 0.008 0.008 0.010 0.010 0.012 0.012 Switching system: LL = Low level switching element, SA = Snap-action switching element Contacts: NC = Normally closed, NO = Normally open Switching action: MA = Maintained action, M = Momentary action Terminals: UT = Universal terminal, S = Soldering terminal, S1 = Soldering terminal (also pluggable 2.8 x 0.5 mm) Component layout from page 40, Mounting dimensions from page 41, Technical drawing from page 42, Circuit drawing from page 47 14 01.2010 51 Devices flush mounting Keylock switch actuator 2 positions, flush mounting Essential Accessories: d Front bezel set for Keylock switch, flush mounting page 26 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 4 3 4 3 3 3 3 3 3 Continuation see next page 15 01.2010 Circuit drawing 4 4 4 4 4 4 Technical drawing IP 65 LL 1 NC + 1 NO MA UT A Keylock switch actuator 2 positions, flush mounting C Position A : Basic position C+A Position C : Maintained action 2 NO MA UT A Standard lock 311 C Front : Plastic black C+A SA 1 NC + 1 NO MA S A C C+A S1 A C C+A 2 NC + 2 NO MA S A C C+A 3 NC + 3 NO MA S A C C+A 4 NC + 4 NO MA S A C C+A IP 65 LL 1 NC + 1 NO M UT A Position A : Basic position Position C : Momentary action 2 NO M UT A Standard lock 311 SA 1 NC + 1 NO M S A Front : Plastic black S1 A 2 NC + 2 NO M S A 3 NC + 3 NO M S A 4 NC + 4 NO M S A b 24 x 24 mm a 24 x 30 mm O 25 mm Typ-Nr. Typ-Nr. Typ-Nr. 51-445.036DF 51-448.036DF 51-442.036DF 51-444.036DF 51-447.036DF 51-441.036DF 51-255.025D2F 51-355.025D2F 51-155.025D2F 51-255.022DF 51-355.022DF 51-155.022DF 51-256.025D2F 51-356.025D2F 51-156.025D2F 51-257.025D2F 51-357.025D2F 51-157.025D2F 51-258.025D2F 51-358.025D2F 51-158.025D2F 51-458.036DF 51-457.036DF 51-145.025D2F 51-145.022DF 51-146.025D2F 51-147.025D2F 51-148.025D2F Component layout Mounting dimensions Key remove Terminals Switching action Contacts Switching system 0 Front protection Continuation see next page e 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 76 76 76 77 77 77 72 72 72 72 72 72 73 73 73 74 74 74 75 75 75 70 71 66 66 67 68 69 0.027 0.027 0.027 0.027 0.027 0.027 0.027 0.027 0.027 0.027 0.027 0.027 0.027 0.027 0.027 0.027 0.027 0.027 0.027 0.027 0.027 0.027 0.027 0.027 0.027 0.027 0.027 0.027 51 S1 2 NC + 2 NO MA S 3 NC + 3 NO MA S 4 NC + 4 NO MA S IP 65 LL 1 NC + 1 NO M Position A : Basic position Position C : Momentary action 2 NO M Standard lock 311 SA 1 NC + 1 NO M Front : Plastic black Position A : Basic position Position C : Maintained action Standard lock 311 Front : Plastic black 2 NC + 2 NO 3 NC + 3 NO 4 NC + 4 NO IP 65 LL 1 NC + 1 NO 2 NO UT UT S S1 M S M S M S MA UT MA UT SA 1 NC + 1 NO MA S S1 2 NC + 2 NO MA S 3 NC + 3 NO MA S 4 NC + 4 NO MA S Component layout Mounting dimensions a 24 x 30 mm O 25 mm Typ-Nr. Typ-Nr. 51-405.036DF 51-408.036DF 51-402.036DF 51-404.036DF 51-407.036DF 51-401.036DF 51-295.025D2F 51-395.025D2F 51-195.025D2F 51-295.022DF 51-395.022DF 51-195.022DF 51-296.025D2F 51-396.025D2F 51-196.025D2F 51-297.025D2F 51-397.025D2F 51-197.025D2F 51-298.025D2F 51-398.025D2F 51-198.025D2F 51-428.036DF 51-427.036DF 51-495.025D2F 51-495.022DF 51-496.025D2F 51-497.025D2F 51-498.025D2F 51-415.036DF 51-418.036DF 51-412.036DF 51-414.036DF 51-417.036DF 51-411.036DF 51-235.025D2F 51-335.025D2F 51-135.025D2F 51-235.022DF 51-335.022DF 51-135.022DF 51-236.025D2F 51-336.025D2F 51-136.025D2F 51-237.025D2F 51-337.025D2F 51-137.025D2F 51-238.025D2F 51-338.025D2F 51-138.025D2F 4 4 4 4 4 4 4 4 4 4 4 4 4 4 Continuation see next page 16 01.2010 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 Circuit drawing SA 1 NC + 1 NO MA S A C C+A A C C+A A C C+A A C C+A A C C+A A C C+A A C C+A A A A A A A A A C C+A A C C+A A C C+A A C C+A A C C+A A C C+A A C C+A b 24 x 24 mm Typ-Nr. Technical drawing IP 65 LL 1 NC + 1 NO MA UT Position A : Basic position Position C : Maintained action Standard lock 311 Front : Plastic black 2 NO MA UT Key remove Terminals Switching action Contacts 0 Switching system Front protection Devices flush mounting e 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 76 76 76 77 77 77 72 72 72 72 72 72 73 73 73 74 74 74 75 75 75 70 71 66 66 67 68 69 76 76 76 77 77 77 72 72 72 72 72 72 73 73 73 74 74 74 75 75 75 0.029 0.029 0.029 0.029 0.029 0.029 0.029 0.029 0.029 0.029 0.029 0.029 0.029 0.029 0.029 0.029 0.029 0.029 0.029 0.029 0.029 0.029 0.029 0.029 0.029 0.029 0.029 0.029 0.026 0.026 0.026 0.026 0.026 0.026 0.026 0.026 0.026 0.026 0.026 0.026 0.026 0.026 0.026 0.026 0.026 0.026 0.026 0.026 0.026 51 Devices flush mounting IP 65 LL 1 NC + 1 NO M Position A : Basic position Position C : Momentary action 2 NO M Standard lock 311 SA 1 NC + 1 NO M Front : Plastic black 2 NC + 2 NO M 3 NC + 3 NO M 4 NC + 4 NO M UT UT S S1 S S S A A A A A A A Circuit drawing Technical drawing b 24 x 24 mm Typ-Nr. Component layout Mounting dimensions Key remove Terminals Switching action Contacts Switching system 0 Front protection Continued from previous page a 24 x 30 mm O 25 mm e Typ-Nr. Typ-Nr. 51-438.036DF 4 3 17 70 0.026 51-437.036DF 4 3 17 71 0.026 51-141.025D2F 3 17 66 0.026 51-141.022DF 3 17 66 0.026 51-142.025D2F 3 17 67 0.026 51-143.025D2F 3 17 68 0.026 51-144.025D2F 3 17 69 0.026 Other lock numbers on request Switching system: LL = Low level switching element, SA = Snap-action switching element Contacts: NC = Normally closed, NO = Normally open Switching action: MA = Maintained action, M = Momentary action Terminals: UT = Universal terminal, S = Soldering terminal, S1 = Soldering terminal (also pluggable 2.8 x 0.5 mm) Component layout from page 40, Mounting dimensions from page 41, Technical drawing from page 42, Circuit drawing from page 47 17 01.2010 51 Devices flush mounting Keylock switch actuator 3 positions, flush mounting Essential Accessories: d Front bezel set for Keylock switch, flush mounting page 26 a 24 x 30 mm Typ-Nr. 51-361.022DF 51-363.022DF 51-362.022DF 01.2010 O 25 mm e Typ-Nr. 51-371.022DF 3 4 65 0.027 51-373.022DF 3 4 65 0.027 51-372.022DF 3 4 65 0.027 51-365.022DF 51-375.022DF 3 4 64 0.027 51-366.022DF 51-376.022DF 3 4 64 0.027 51-367.022DF 51-377.022DF 3 4 62 0.027 51-368.022DF 51-378.022DF 3 4 62 0.027 51-364.022DF 51-374.022DF 3 4 63 0.027 Other lock numbers on request Switching system: SA = Snap-action switching element Contacts: NC = Normally closed, NO = Normally open Switching action: MA = Maintained action, M = Momentary action Terminals: S1 = Soldering terminal (also pluggable 2.8 x 0.5 mm) Mounting dimensions from page 41, Technical drawing from page 42, Circuit drawing from page 47 18 Circuit drawing b 24 x 24 mm Typ-Nr. IP 65 SA 2 NC + 2 NO MA-0-MA S1 A 51-381.022DF Keylock switch actuator 3 positions, flush mounting C + B 51-383.022DF Position C : Maintained action C+A+B 51-382.022DF Position A : Basic position Position B : Maintained action Standard lock 311 51-385.022DF Position C : Maintained action IP 65 SA 2 NC + 2 NO MA-0-M S1 A Position A : Basic position C + A 51-386.022DF Position B : Momentary action Standard lock 311 51-387.022DF Position C : Momentary action IP 65 SA 2 NC + 2 NO M-0-MA S1 A Position A : Basic position A + B 51-388.022DF Position B : Maintained action Standard lock 311 S1 A 51-384.022DF Position C : Momentary action IP 65 SA 2 NC + 2 NO M-0-M Position A : Basic position Position B : Momentary action Standard lock 311 0 Mounting dimensions Technical drawing Key remove Terminals Switching action Contacts Switching system Front protection Continuation see next page 51 Devices flush mounting Selector switch actuator 2 positions, flush mounting illuminative Actuators usable for front dimensions: b 24 x 24 mm | 25 mm dia. Essential Accessories: Front bezel set for Selector switch, flush mounting page 26 d d d Lever, flush mounting page 24 Single-LED page 30 2 NC + 2 NO 3 NC + 3 NO 4 NC + 4 NO 1 NC 1 NC + 1 NO 1 NO 2 NC 2 NO 1 NC + 1 NO MA MA MA M M M M M M Position A : Basic position Position C : Momentary action IP 65 LL SA 2 NC + 2 NO 3 NC + 3 NO 4 NC + 4 NO M M M Typ-Nr. 52-476.036 52-473.036 52-475.036 52-472.036 52-471.036 52-271.0252 52-271.022 52-272.0252 52-273.0252 52-274.0252 52-436.036 52-433.036 52-435.036 52-432.036 52-431.036 52-131.0252 52-131.022 52-132.0252 52-133.0252 52-134.0252 4 4 4 4 4 4 4 4 4 4 Circuit drawing SA UT UT UT UT UT S S1 S S S UT UT UT UT UT S S1 S S S Technical drawing Selector switch actuator 2 positions, flush mounting Position A : Basic position Position C : Maintained action Mounting dimensions MA MA MA MA MA MA 0 Component layout 1 NC 1 NC + 1 NO 1 NO 2 NC 2 NO 1 NC + 1 NO Terminals LL Switching action Switching system IP 65 Contacts Front protection Continuation see next page e 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 43 46 45 44 47 42 39 38 35 34 29 32 31 30 33 28 25 24 21 20 0.007 0.007 0.007 0.007 0.007 0.006 0.006 0.006 0.006 0.006 0.007 0.007 0.007 0.007 0.007 0.006 0.006 0.006 0.006 0.006 Switching system: LL = Low level switching element, SA = Snap-action switching element Contacts: NC = Normally closed, NO = Normally open Switching action: MA = Maintained action, M = Momentary action Terminals: UT = Universal terminal, S = Soldering terminal, S1 = Soldering terminal (also pluggable 2.8 x 0.5 mm) Component layout from page 40, Mounting dimensions from page 41, Technical drawing from page 42, Circuit drawing from page 47 19 01.2010 51 Devices flush mounting Selector switch actuator 3 positions, flush mounting illuminative Actuators usable for front dimensions: b 24 x 24 mm | 25 mm dia. Essential Accessories: Front bezel set for Selector switch, flush mounting page 26 d d d Lever, raised mounting page 24 Single-LED page 30 Switching action Terminals SA 2 NC + 2 NO MA-0-MA M-0-MA S1 S1 Typ-Nr. 52-571.022A 52-574.022A IP 40 SA 2 NC + 2 NO MA-0-M M-0-M S1 S1 52-573.022A 52-572.022A Switching system: SA = Snap-action switching element Contacts: NC = Normally closed, NO = Normally open Switching action: MA = Maintained action, M = Momentary action Terminals: S1 = Soldering terminal (also pluggable 2.8 x 0.5 mm) Mounting dimensions from page 41, Technical drawing from page 42, Circuit drawing from page 47 20 01.2010 Circuit drawing Contacts Selector switch actuator 3 positions, flush mounting Position C : Maintained action Position A : Basic position Position B : Maintained action Position C : Momentary action Position A : Basic position Position B : Momentary action Technical drawing Switching system IP 40 0 Mounting dimensions Front protection Continuation see next page e 3 3 5 5 19 17 0.015 0.015 3 3 5 5 18 16 0.015 0.015 51 Accessories Front Lens plastic, raised mounting Continuation see next page Lens blue transparent colourless transparent green transparent orange transparent red transparent yellow transparent blue transparent colourless transparent green transparent orange transparent red transparent smoked transparent yellow transparent blue translucent colourless transparent green translucent green transparent orange translucent red translucent red transparent white translucent yellow translucent yellow transparent black opaque grey opaque colourless transparent green transparent red transparent yellow transparent Lens plastic, raised mounting concave, illuminative flush, illuminative flush, illuminative (not recommended for film insert) flush, non-illuminative concave, illuminative (not recommended for film insert) b 18 x 18 mm Typ-Nr. 51-954.6 51-954.7 51-954.5 51-954.3 51-954.2 51-954.4 51-953.6 51-953.7 51-953.5 51-953.3 51-953.2 51-953.1 51-953.4 51-951.6 51-955.7 51-951.5 51-955.5 51-951.3 51-951.2 51-955.2 51-951.9 51-951.4 51-955.4 51-951.0 51-951.8 a 18 x 24 mm Typ-Nr. 51-904.6 51-904.7 51-904.5 51-904.3 51-904.2 51-904.4 51-903.6 51-903.7 51-903.5 51-903.3 51-903.2 51-903.1 51-903.4 51-901.6 51-905.7 51-901.5 51-905.5 51-901.3 51-901.2 51-905.2 51-901.9 51-901.4 51-905.4 51-901.0 51-901.8 51-906.7 51-906.5 51-906.2 51-906.4 O 18 mm Typ-Nr. 51-933.6 51-933.7 51-933.5 51-933.3 51-933.2 51-933.1 51-933.4 51-931.6 51-935.7 51-931.5 51-935.5 51-931.3 51-931.2 51-935.2 51-931.9 51-931.4 51-935.4 51-931.0 51-931.8 e 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 Lens plastic, flush mounting mat Continuation see next page Lens plastic, flush mounting illuminative non-illuminative Lens blue transparent flush colourless transparent flush green transparent flush orange transparent flush red transparent flush smoked transparent flush yellow transparent flush black opaque flush grey opaque flush white translucent flush b 24 x 24 mm Typ-Nr. 61-9671.6 61-9671.7 61-9671.5 61-9671.3 61-9671.2 61-9671.1 61-9671.4 61-9771.0 61-9771.8 61-9771.9 a 24 x 30 mm Typ-Nr. 61-9681.6 61-9681.7 61-9681.5 61-9681.3 61-9681.2 61-9681.1 61-9681.4 61-9781.0 61-9781.8 61-9781.9 O 25 mm Typ-Nr. 61-9642.6 61-9642.7 61-9642.5 61-9642.3 61-9642.2 61-9642.1 61-9642.4 e 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 21 01.2010 51 Accessories Lens plastic with symbol, flush mounting Continuation see next page Lens plastic with symbol, flush mounting flush - level, illuminative Symbol ON/OFF Ring Stand by Lens blue transparent colourless transparent green transparent red transparent blue transparent colourless transparent green transparent orange transparent red transparent yellow transparent blue transparent colourless transparent green transparent red transparent O 25 mm Typ-Nr. 61-9643.602 61-9643.702 61-9643.502 61-9643.202 61-9643.601 61-9643.701 61-9643.501 61-9643.301 61-9643.201 61-9643.401 61-9643.603 61-9643.703 61-9643.503 61-9643.203 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 Typ-Nr. 61-9707.7 0.001 O 25 mm Typ-Nr. 61-9841.0A 61-9841.6A 61-9841.4A 61-9841.8A 61-9841.5A 61-9841.2A 0.002 0.002 0.002 0.002 0.002 0.002 e The silvery coat is being applied on the lens (screen print) with an additional protective lacquer. Marking plate for lens round plastic, flush mounting can be hot stamped Continuation see next page Marking plate for lens round plastic, flush mounting only applicable with Lens round Typ-Nr. 61-9642.X Marking plate Plastic colourless transparent e Lens metal with spot, flush mounting mat Continuation see next page Lens metal with spot, flush mounting 22 01.2010 Lens Aluminium black flush Aluminium blue flush Aluminium gold flush Aluminium natural flush Aluminium olive-green flush Aluminium red flush e 51 Accessories Lens metal, flush mounting mat Continuation see next page Lens metal, flush mounting convex flush O 25 mm Typ-Nr. 61-9842.0 61-9842.6 61-9842.4 61-9842.8 61-9842.5 61-9842.2 61-9841.0 61-9841.6 61-9841.4 61-9841.8 61-9841.5 61-9841.2 0.003 0.003 0.003 0.003 0.003 0.003 0.002 0.002 0.002 0.002 0.002 0.002 O 32 mm Typ-Nr. 61-9593.0 61-9593.5 61-9593.2 61-9593.4 0.004 0.004 0.004 0.004 Front bezel Plastic black Typ-Nr. 52-950.0 0.001 Plastic black 52-952.0 0.001 Lens Aluminium black Aluminium blue Aluminium gold Aluminium natural Aluminium olive-green Aluminium red Aluminium black Aluminium blue Aluminium gold Aluminium natural Aluminium olive-green Aluminium red e Mushroom-head cap, flush mounting Continuation see next page Mushroom-head cap, flush mounting Mushroom had cap Plastic black opaque Plastic green opaque Plastic red opaque Plastic yellow opaque e Front bezel square for selector switch, raised mounting Continuation see next page Front bezel square for selector switch, raised mounting 24 x 24 mm 26 x 26 mm e 23 01.2010 51 Accessories Lever, raised mounting with bar and marking dot Continuation see next page Lever, raised mounting illuminative Lever Plastic black Plastic grey non-illuminative Plastic black Plastic grey Bar colour blue green orange red yellow blue green orange red yellow black grey white e Typ-Nr. 52-928.60 52-928.50 52-928.30 52-928.20 52-928.40 52-929.60 52-929.50 52-929.30 52-929.20 52-929.40 52-928.0 52-929.8 52-929.9 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 Typ-Nr. 61-9028.60 61-9028.50 61-9028.30 61-9028.20 61-9028.40 61-9029.60 61-9029.50 61-9029.30 61-9029.20 61-9029.40 61-9028.0 61-9028.9 61-9029.8 61-9029.9 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 Lever, flush mounting with bar and marking dot Continuation see next page Lever, flush mounting illuminative Lever Plastic black Plastic grey non-illuminative Plastic black Plastic grey Bar colour blue green orange red yellow blue green orange red yellow black white grey white e Legend frame for devices 25 mm dia., flush mounting Legend frame 30 x 50 mm, adhesive, Aluminium black Technical drawing from page 42 24 01.2010 Typ-Nr. 61-9980.0 Technical drawing Continuation see next page e 10 0.001 51 Accessories Legend plate insert for Legend frame 61-9980.0 Continuation see next page Legend plate insert 14.5 x 23.5 mm, adhesive, Aluminium black 14.5 x 23.5 mm, adhesive, Aluminium natural e Typ-Nr. 704.968.1 0.001 704.968.0 0.001 Front bezel set for Indicators and Illuminated pushbutton, flush mounting b 24 x 24 mm Typ-Nr. 61-9930.0 61-9930.4 a 24 x 30 mm Typ-Nr. 61-9931.0 61-9931.4 Mounting dimensions Front bezel set for Indicators and Illuminated pushbutton, flush mounting Front bezel Plastic black Plastic silver Aluminium black Aluminium blue Aluminium gold Aluminium natural Aluminium olive-green Aluminium red e 61-9933.1 61-9933.6 61-9933.4 61-9933.0 61-9933.5 61-9933.2 3 3 3 3 3 3 3 3 0.008 0.008 0.006 0.006 0.006 0.006 0.006 0.006 O 25 mm Typ-Nr. Mounting dimensions Continuation see next page e 61-9933.1 61-9933.6 61-9933.4 61-9933.0 61-9933.5 61-9933.2 61-9933.10 4 4 4 4 4 4 4 4 0.013 0.006 0.006 0.006 0.006 0.006 0.006 0.008 O 25 mm Typ-Nr. 61-9933.10 Mounting dimensions from page 41 Front bezel set for Mushroom-head pushbutton, flush mounting Continuation see next page Front bezel set for Mushroom-head pushbutton, flush mounting Front bezel Aluminium natural Aluminium black Aluminium blue Aluminium gold Aluminium natural Aluminium olive-green Aluminium red Plastic black O 40 mm Typ-Nr. 61-9934.8 Mounting dimensions from page 41 25 01.2010 51 Accessories Front bezel set for Keylock switch, flush mounting Mounting dimensions Front bezel set for Keylock switch, flush mounting Front bezel Plastic black Plastic silver Aluminium black Aluminium blue Aluminium gold Aluminium natural Aluminium olive-green Aluminium red e 61-9932.1 61-9932.6 61-9932.4 61-9932.0 61-9932.5 61-9932.2 3 3 3 3 3 3 3 3 0.008 0.008 0.006 0.006 0.006 0.006 0.006 0.006 O 25 mm Typ-Nr. Mounting dimensions Continuation see next page e 61-9932.1 61-9932.6 61-9932.4 61-9932.0 61-9932.5 61-9932.2 61-9932.10 3 3 3 3 3 3 3 3 0.007 0.006 0.006 0.006 0.006 0.006 0.006 0.008 Front protective cap Silicone natural transparent Typ-Nr. 61-9927.2 0.001 Silicone natural transparent 84-9103.7 0.001 b 24 x 24 mm Typ-Nr. 61-9930.0 61-9930.4 a 24 x 30 mm Typ-Nr. 61-9931.0 61-9931.4 O 25 mm Typ-Nr. 61-9932.10 With the round front bezel sets O25 mm the anti-twist ring is part of the sales-package. Mounting dimensions from page 41 Front bezel set for Selector switch, flush mounting Continuation see next page Front bezel set for Selector switch, flush mounting Front bezel Plastic black Aluminium black Aluminium blue Aluminium gold Aluminium natural Aluminium olive-green Aluminium red Plastic black b 24 x 24 mm Typ-Nr. 61-9936.0 With the round front bezel sets O25 mm the anti-twist ring is part of the sales-package. Mounting dimensions from page 41 Front protective cap for flush - level lenses only for protection IP 68 Continuation see next page Front protective cap for front bezel set 24 x 30 mm, flush mounting for front bezel set 25 mm dia., flush mounting e ATTENTION when using the front protection cover for push buttons the external sealing in the front bezel set and the silicone bellows in the actuator are to be removed ! 26 01.2010 51 Accessories Protective cover, raised mounting b 18 x 18 mm Typ-Nr. 51-920 Protective cover, raised mounting hinged, transparent, with means for sealing a 18 x 24 mm Typ-Nr. Technical drawing Continuation see next page e 51-925 2 3 0.002 0.002 Technical drawing from page 42 Protective cover, flush mounting a 24 x 30 mm Typ-Nr. O 25 mm Typ-Nr. Technical drawing Protective cover, flush mounting hinged, transparent, with means for sealing b 24 x 24 mm Typ-Nr. 61-9921.0 Mounting dimensions Continuation see next page e 61-9924.0 3 3 3 7 8 9 0.006 0.006 0.006 61-9922.0 slide by side, with means not for sealing Mounting dimensions from page 41, Technical drawing from page 42 Blind plug, raised mounting Blind plug, raised mounting Blind plug Plastic black b 18 x 18 mm Typ-Nr. 51-948.0 a 18 x 24 mm Typ-Nr. 51-947.0 O 18 mm Typ-Nr. 51-949.0 Mounting dimensions Continuation see next page e 1 0.003 Blind plugs fit also in mounting holes no. 2 Mounting dimensions from page 41 Blind plug, flush mounting b 24 x 24 mm Typ-Nr. 61-9451.0 a 24 x 30 mm Typ-Nr. 61-9452.0 O 25 mm Typ-Nr. 61-9453.0 3 3 Technical drawing Blind plug, flush mounting Blind plug Plastic black Mounting dimensions Continuation see next page e 11 0.006 0.006 Mounting dimensions from page 41, Technical drawing from page 42 27 01.2010 51 Accessories Master key Continuation see next page Master key Lock numbers 311 ... 445 (DOM) e Typ-Nr. 31-989.300 0.006 Typ-Nr. 31-989.311 0.006 Typ-Nr. 31-985.0 0.005 Spare key Continuation see next page Spare key Key lock switch, standard lock 311 (DOM) e Other lock numbers on request EMC Key protection cap Continuation see next page EMC Key protection cap Plastic black, for lock type DOM e > Backside PCB plug-in base PCB plug-in base 16.4 mm dia. x 9.8 mm for Low level switching element, Pins axial 17.8 x 12.9 mm x 9.8 mm for Snap-action switching element 2.8 mm, Pins axial 17.9 x 17.9 x 8.4 mm for Low level switching element, Pins bent at right-angle P Typ-Nr. 31-940 P P 31-942 31-941 Component layout Terminals Continuation see next page e 2 0.002 3 1 0.002 0.004 PCB plug-in base Pins right-angle : With the extendable mounting the distance between plug-in base and PCB can be varied up to 3 mm. Terminals: P = PCB terminal Component layout from page 40 Multi-plug housing Continuation see next page Multi-plug housing for Switching block 28 01.2010 Typ-Nr. 51-943.0 e 0.005 51 Accessories Flat receptacle Continuation see next page Flat receptacle 2.0 x 0.5 mm for Universal terminal 2.8 x 0.5 mm for Multi-plug housing 2.8 x 0.5 mm for Plug-in terminal e Typ-Nr. 31-945 0.001 51-943.1 31-946 0.001 0.001 Typ-Nr. 01-928 0.001 31-928 31-929 0.001 0.001 Typ-Nr. 01-929 0.010 Typ-Nr. 10-1309.1309 10-1310.1319 10-1311.1249 10-1312.1229 10-1313.1209 10-1313.1249 10-1316.1179 10-1316.1209 10-1319.1179 10-1319.1199 10-1306.1349 10-1307.1369 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 Insulation sleeve Continuation see next page Insulation sleeve Cover Plug-in terminals for snap-action switching element 2.8 mm for Flat receptacle 31-945 for Flat receptacle 31-946 e Terminal cover Continuation see next page Terminal cover e > Illumination Filament lamp Continuation see next page Socket Filament lamp 3 T1 /4 MG Operating voltage/-current 12 VAC/DC, 75 mA 14 VAC/DC, 80 mA 18 VAC/DC, 40 mA 24 VAC/DC, 35 mA 28 VAC/DC, 30 mA 28 VAC/DC, 40 mA 36 VAC/DC, 20 mA 36 VAC/DC, 30 mA 48 VAC/DC, 20 mA 48 VAC/DC, 25 mA 6 VAC/DC, 120 mA 6.3 VAC/DC, 200 mA e 29 01.2010 51 Accessories Single-LED Continuation see next page Socket Single-LED T1 3/4 MG Light colour blue green red white diffuse yellow Operating voltage/-current 12 VAC/DC, 7/14 mA 24 VAC/DC, 7/14 mA 28 VAC/DC, 7/14 mA 48 VAC/DC, 4/8 mA 6 VDC, 15 mA 12 VAC/DC, 4/7 mA 24 VAC/DC, 4/7 mA 28 VAC/DC, 4/7 mA 48 VAC/DC, 2/4 mA 6 VDC, 7 mA 12 VAC/DC, 7/14 mA 24 VAC/DC, 7/14 mA 28 VAC/DC, 7/14 mA 48 VAC/DC, 4/8 mA 6 VDC, 15 mA 12 VAC/DC, 7/14 mA 24 VAC/DC, 7/14 mA 28 VAC/DC, 7/14 mA 48 VAC/DC, 4/8 mA 6 VDC, 15 mA 12 VAC/DC, 7/14 mA 24 VAC/DC, 7/14 mA 28 VAC/DC, 7/14 mA 48 VAC/DC, 4/8 mA 6 VDC, 15 mA e Typ-Nr. 10-2J09.1066 10-2J12.1066 10-2J13.1066 10-2J19.1046 10-2J06.3146 10-2J09.1065 10-2J12.1065 10-2J13.1065 10-2J19.1045 10-2J06.3145 10-2J09.1062 10-2J12.1062 10-2J13.1062 10-2J19.1042 10-2J06.3142 10-2J09.1069 10-2J12.1069 10-2J13.1069 10-2J19.1049 10-2J06.3149 10-2J09.1064 10-2J12.1064 10-2J13.1064 10-2J19.1044 10-2J06.3144 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 Operating voltage 230/240 V Typ-Nr. 02-904.7 0.003 110 V 125 V 145 V 02-904.0 02-904.1 02-904.3 0.003 0.003 0.003 Typ-Nr. 02-912.2 e 0.045 02-912.3 02-912.4 02-912.1 0.090 0.095 0.025 Note: AC operation through halve-wave rectifier possible, slight flickering can occure. Series resistor for lamp voltage reduction Continuation see next page Series resistor 10 k, for filament lamp 48 VAC, 25 mA 2.7 k, for filament lamp 48 VAC, 25 mA 3.3 k, for filament lamp 48 VAC, 25 mA 4.7 k, for filament lamp 48 VAC, 25 mA e Please keep to the country specific security rules. Terminal plate empty for fitting with series resistors Continuation see next page Terminal plate empty 10 spaces 125 x 60 x 15 mm 15 spaces 187.5 x 60 x 15 mm 20 spaces 250 x 60 x 15 mm 5 spaces 62.5 x 60 x 15 mm 30 01.2010 51 Accessories > Assembling Fixing nut Continuation see next page Fixing nut Metal, specifically for keylock switches e Typ-Nr. 31-991 0.005 Typ-Nr. 51-910 0.001 Typ-Nr. 61-9730.0 0.011 02-905 0.011 Typ-Nr. 61-9740.0 0.003 Typ-Nr. 01-907 0.020 Typ-Nr. 51-938 0.027 Anti-twist ring for Key lock- and Selector switch Continuation see next page Anti-twist ring e Lens remover Continuation see next page Lens remover for flush mounting for raised mounting e Lamp remover Continuation see next page Lamp remover e CAUTION A switching process might be released when replacing the lamp/LED ! Mounting tool Continuation see next page Mounting tool e Dismantling tool Continuation see next page Dismantling tool for dismantling of Lens, Lens holder and Switching element block e 31 01.2010 51 Accessories Flat receptacle remover Continuation see next page Flat receptacle remover for removing the Flat receptacle of the Multi-plug in housing 32 01.2010 Typ-Nr. 51-943.9 e 0.001 51 Technical Data Rated voltage 250 VAC/VDC Actuator with snap-action switching element Rated current 5A Switching system Self-cleaning, double-break, snap action switching system (with contact gap 2 x 0.5 mm). 1 normally closed or 1 normally open contact per element. Snap-action switching elements with soldering terminals at the sides: up to 4 switching element can be on a pushbutton (max. 4 normally closed and 4 normally open contacts). Snap-action switching element with axial plug-in terminals 2.8 mm stachable, only 1 switching element can be on a pushbutton. Contact resistance Starting value (initial) 50 m Electrostatic discharge (ESD) 15 KV (Keylock switch) Conventional free air thermal current 5A The maximum current in continuous operation and at ambient temperature not exceeding the quoted maximum values. Material Material of contact Gold plated silver Switch housing Axial soldering-/plug-in terminal 2.8 mm: Diallylphthalate DAP, Polyamide 66, Polysulfone, heat-resistant and self-extinguishing. Soldering terminal: PA 6.6 Ultramid Actuator housing Polyetherimide, self-extinguishing Mechanical characteristics Terminals Snap-action switching element with tinned soldering terminals at the sides: Max. wire diameter 2 wires a 1.2 mm Max. wire cross-section of stranded cable 1 x 1 mm Snap-action switching element with axial soldering terminals, which can also be used as plug-in terminals 2.8 x 0.5 mm: Max. wire diameter 2 wires of 1 mm Max. wire cross-section of stranded cable 2 of 0.75 mm or 1 x 1.0 mm Actuating torque 2.5 Ncm ... 5.5 Ncm, depending on the number of switching elements. Measured at the key or lever of the keylock- or selector switch. Actuating force 4 N ... 6 N, depending on the number of switching elements Actuating travel Illuminated pushbutton 3 mm Keylock-/selector switch actuator 2 positions: 1x ca. 42 deflection momentary action 1x ca. 90 deflection maintained action Rebound time 5ms Switch rating AC (cos 0,7) 0 Voltage Current 125 VAC 3A 250 VAC 2A Switch rating DC (inductive) L:R = 30 ms 0 Voltage Current 24 VDC 2A 60 VDC 0.7 A 110 VDC 0.2 A 220 VDC 0.1 A Electric strength 2500 VAC, 50 Hz, 1 min. between all terminals and earth, as per IEC 60512-2-11 Protection class II Environmental conditions Storage temperature -40 C ... +85 C Service temperature -25 C ... +55 C For indicators and illuminated pushbuttons mounted as a block, make sure the heat can escape freely. Protection degree IP 65 front side, as per IEC 60529 Shock resistance (Single impacts, semi-sinusoidal) 15 g for 11 ms, as per IEC 60512-4-3, IEC 60068-2-27 Vibration resistance (Sinusoidal) 10 g at 10 Hz ... 1500 Hz, amplitude 1.5 mm, as per IEC 60512-44, IEC 60068-2-6 Climate resistance Standard condition, as per IEC 60068-2-3 and 2-30 Changing condition, as per IEC 60068-2-14 and 2-33 Mechanical lifetime 0 Momentary action Maintained action Keylock switch Switch rating 250 VAC, 5 A (cos 1) 250 VAC, 3 A (cos 0,3) 2 million cycles of operation 1 million cycles of operation 50 000 cycles of operation Electrical characteristics Standards IEC 61058, EN 61058 Approvals Approbations CB (IEC 61058) CSA ENEC (EN 61058) Germanischer Lloyd UL 33 01.2010 51 Technical Data Declaration of conformity CE Environmental conditions > Storage temperature -40 C ... +85 C Actuator with snap-action switching element block (Keylock- and Selector switch 3 positions) Service temperature -25 C ... +55 C for selector switches mounted as a block, make sure the heat can escape freely Switching system Self-cleaning, double-break, snap action switching system 1 normally closed or 1 normally open contact per element. Protection degree Front side, as per IEC 60529 IP 65 keylock switch IP 40 selector switch Material Material of contact Gold plated hardsilver Switch housing Diallylphthalate (DAP), heat-resistant and self-extinguishing Approvals Approbations CB (IEC 61058) CSA ENEC (EN 61058) Germanischer Lloyd UL Actuator housing Polyetherimide, self-extinguishing Mechanical characteristics Terminals Soldering terminal which can also be used as plug-in terminal 2.8 x 0.5 mm: Max. wire diameter 2 wires of 1 mm Max. wire cross-section of stranded cable 2 x 0.75 mm Actuating torque 2.5 Ncm ... 5.5 Ncm, depending on the number of switching elements. Measured at the key or lever of the keylock- or selector switch. Actuating travel Keylock-/selector switch actuator with 3 positions 2x ca. 42 deflection momentary action 2x ca. 90 deflection maintained action Rebound time 5ms Mechanical lifetime Declaration of conformity CE > Actuator with low level switching element Switching system This low level switching element was designed for switching low powers in electronic circuits. The mechanism assures reliable switching of loads ranging from a few A / V up to 100 mA / 42 VAC/ DC. Single-break momentary contact, as normally open or normally closed with 4 independent points of contact. 2 momentary contacts per switching element; combination of normally open and normally closed is possible. Special features are the long life, extremely short rebound time and stable contact resistance. Material 0 Keylock switch Selector switch 50 000 cycles of operation 100 000 cycles of operation Electrical characteristics Electrostatic discharge (ESD) 15 KV (Keylock switch) Conventional free air thermal current 5A The maximum current in continuous operation and at ambient temperature not exceeding the quoted maximum values. Switch rating 250 VAC, 5 A (cos 0,75) Electric strength 2500 VAC, 50 Hz, 1 min. between all terminals and earth, as per IEC 60512-2-11 Protection class II Material of contact Gold plated Switch housing Polysulfone, heat-resistant and self-extinguishing Actuator housing Polyetherimide, self-extinguishing Mechanical characteristics Terminals The universal terminals permit these units to be mounted on printed circuit boards (PCB). These terminals can also be used as soldering or plug-in terminals. For these terminals we can also supply a plug-in base which, when soldered on to the board, enables the switch to be plugged in. Soldering terminal: Max. wire diameter 2 wires a 0.8 mm Max. wire cross-section of stranded cable 1x 0.75 mm Plug-in terminal 2.0 x 0.5 mm Actuating torque 2.5 Ncm ... 5.5 Ncm, measured at the key or lever of the keylock- or selector switch 34 01.2010 51 Technical Data Actuating force 3 N ... 3,5 N Actuating travel Illuminated pushbutton 3 mm Keylock-/selector switch actuator 2 positions: 1x ca. 42 deflection momentary action 1x ca. 90 deflection maintained action Rebound time Typ. <100 s Mechanical lifetime 0 Momentary action Maintained action Keylock switch 5 million cycles of operation 1 million cycles of operation 50 000 cycles of operation Electrical characteristics Contact resistance Starting value (initial) 50 m Electrostatic breakdown value 15 KV (Keylock switch) Switch rating 10 A, 100 V to 100 mA at 42 VAC/VDC Electric strength 2500 VAC, 50 Hz, 1 min. between all terminals and earth, as per IEC 60512-2-11 Environmental conditions Storage temperature -40 C ... +85 C Service temperature -25 C ... +55 C For indicators and illuminated pushbuttons mounted as a block, make sure the heat can escape freely. Protection degree IP 65 front side, as per IEC 60529 Shock resistance (Single impacts, semi-sinusoidal) 15 g for 11 ms, as per IEC 60512-4-3, IEC 60068-2-27 35 01.2010 Typical Applications Diode element When indicators and illuminated pushbuttons equipped with diodes, the user is able to perform a lamp check or wire an alarm circuit simply with a considerable saving of space. 0 36 01.2010 51 51 Application guidelines Suppressor circuits When switching inductive loads such as relays, DC motors, and DC solenoids, it is always important to absorb surges (e.g. with a diode) to protect the contacts. When these inductive loads are switched off, a counter emf can severely damage switch contacts and greatly shorten lifetime. Fig. 1 shows an inductive load with a free-wheeling diode connected in parallel. This free-wheeling diode provides a path for the inductor current to flow when the current is interrupted by the switch. Without this free-wheeling diode, the voltage across the coil will be limited only by dielectric breakdown voltages of the circuit or parasitic elements of the coil. This voltage can be kilovolts in amplitude even when nominal circuit voltages are low (e.g. 12 VDC) see Fig. 2. The free-wheeling diode should be chosen so that the reverse breakdown voltage is greater than the voltage driving the inductive load. The DC blocking voltage (VR) of the free-wheeling diode can be found in the datasheet of a diode. The forward current should be equal or greater than the maximum current flowing through the load. To get an efficient protection, the free-wheeling diode must be connected as close as possible to the inductive load! 0 Counter emf over load without free-wheeling diode Fig. 2 Switching with inductive load Fig. 1 Switch ON OFF 0 VDC + _ Free-wheeling diode Inductive load Sveral hundred to several thousend volts e=L di __ dt 37 01.2010 51 Marking General notes 0 2. Hot stamping For larger series it is worth considering markings by means of hot stamping We will pleased to advise you. For letters and figures, typefaces with 2.5 mm, 3 mm and 4 mm are available. 1. Engraving In addition to the most commonly used world languages, in DIN 1451-3 close spacing, other typefaces are available as Scandinavian, Slavic, Greek, Russian and Polish. Red, blue and black lenses are filled with white colour. Other colour lenses are filled in black. Standard height of letters is 2 mm. If the height is not specified, we will supply 2 mm engraved letters. 3. Film inserts Instead of using engraving the lenses can be fitted with transparent film inserts, as an alternative. For this purpose, though, it is advisible to use transparent lenses. In the case of use of a smoke-black lens the fitted film becomes readable only if the lamp is on. The film thickness is 0.2 mm. Important : Consider pushbutton mounting orientation befor specifying engraving characters ! > Lenses for indicators and illuminated pushbuttons, raised mounting All dimensions in mm 0 Front size (Lens) 18 dia. (15.8 dia.) Film insert max. size 12.8 dia. 18 x 18 (15.3 x 15.3) 12.7 x 12.7 18 x 24 (15.3 x 21.5) 12.7 x 18.7 Height of letters h 2 3 4 5 6 8 2 3 4 5 6 8 2 3 4 5 6 Number of lines 3 2 2 1 1 1 4 3 2 2 1 1 4 5 3 4 2 3 2 1 2 1 8 Number of (target value) capital letters per line 6 5 3 2 2 2 7-8 6-7 4-5 3-4 3 2-3 11 7-8 9 -10 6-7 7 4-5 5-6 3-4 4-5 3 3-4 2-3 Number of (target value) small letters per line 6 6 4 3 3 2 8 7 5 4 3-4 2-3 12 8 10 - 11 7 7-8 5 6 4 5 3-4 3-4 2-3 Image B4 B4 B4 B4 B4 B4 B3 B3 B3 B3 B3 B3 B1 B2 B1 B2 B1 B2 B1 B2 B1 B2 B1 B2 0 Engraving B1 B2 B3 B4 AB abc AB abc AB AB abc > 38 01.2010 h Film abc 51 Marking Lenses for indicators and illuminated pushbuttons, flush mounting All dimensions in mm 0 Front size (Lens) 24 x 24 (18 x 18) Film insert max. size 15.1 x 15.1 24 x 30 (18 x 24) 15.1 x 21 Height of letters h 2 3 4 5 6 8 2 3 4 5 6 25 dia. (19.7 dia.) Marking plate Number of lines 4 3 2 2 1 1 4 5 3 4 2 3 2 8 1 2 1 2 3 4 5 6 8 3 2 2 1 1 1 Number of (target value) capital letters per line 8-9 7-8 4-5 4 4 2-3 12 8-9 10 - 11 7-8 7 4-5 5-6 4 4-5 3 3-4 2-3 6 5 3 2 2 2 Number of (target value) small letters per line 9 8 5 4-5 4 2-3 13 9 11 - 12 8 8 5 6 4-5 5 3-4 3-4 2-3 6 6 4 3 3 2 Image B3 B3 B3 B3 B3 B3 B1 B2 B1 B2 B1 B2 B1 B2 B1 B2 B1 B2 B4 B4 B4 B4 B4 B4 0 Engraving B1 B2 B3 B4 AB abc AB abc AB AB abc h Film abc 39 01.2010 51 Drawings Component layout 1 PCB plug-in base page 28 Extendable mounting pins 3 1 4 2 a 9 4 3 b b 17.9 31 Switch a 42 9.6 17.9 1.27 O1.0 all holes 7.62 15.24 5 x 2.54 1.27 1.27 1.27 0.85 Drilling plan (conductor side) 2 PCB plug-in base page 28 3.81 3.81 O1.0 5.08 10.16 all holes O2.1 hole for central mounting with M2 screw, if desired 12.7 3 PCB plug-in base page 28 7.62 O2.1 hole for central mounting with M2 screw, if desired 10.16 3.81 7.62 3.81 + 0.1 O1.0 0 all holes 4 Indicator actuator page 7 | Illuminated pushbutton actuator page 8 | Keylock switch 2 positions page 9 | Selector switch 2 positions page 11 | Indicator actuator, flush mounting page 13 | Illuminated pushbutton actuator, flush mounting page 14 | Keylock switch actuator 2 positions, flush mounting page 15 | Selector switch actuator 2 positions, flush mounting page 19 Terminal (rearside) PCB layout (conductor side) 7.62 Round Square Rectangular Anti twist device 40 01.2010 O1.0 all holes 10.16 5.08 2 4 1 3 a b 2 4 1 3 a b 2 4 1 3 a b 2.54 3.81 51 Drawings Mounting dimensions 1 Indicator actuator page 7 | Illuminated pushbutton actuator page 8 | Blind plug, raised mounting page 27 18 x 24 mm 16 18 min. O18 mm 18 min. 18 min. 18 x 18 mm +0.2 0 18 min. 24 min. 18 min. 2 Keylock switch 2 positions page 9 | Keylock switch 3 positions page 10 | Selector switch 2 positions page 11 | Selector switch 3 positions page 12 18 x 24 mm 16 +0.2 0 15 +0.05 0 18 min. O18 mm 18 min. 0 1.7 -0.1 18 min. 18 x 18 mm 18 min. 24 min. 18 min. 3 Indicator actuator, flush mounting page 13 | Illuminated pushbutton actuator, flush mounting page 14 | Keylock switch actuator 2 positions, flush mounting page 15 | Keylock switch actuator 3 positions, flush mounting page 18 | Selector switch actuator 2 positions, flush mounting page 19 | Selector switch actuator 3 positions, flush mounting page 20 | Front bezel set for Indicators and Illuminated pushbutton, flush mounting page 25 | Front bezel set for Keylock switch, flush mounting page 26 | Front bezel set for Selector switch, flush mounting page 26 | Protective cover, flush mounting page 27 | Blind plug, flush mounting page 27 24 min. 21 21 25 min. 24 x 24 mm +0.25 -0.15 24 min. 24 x 30 mm +0.25 -0.15 +0.4 22.3 0 25 min. O25 mm +0.25 27 -0.15 30 min. +0.25 21 -0.15 24 min. - Hole spacing min. 26 mm / min. 26 mm by using of the round front protective cap 84-9103.7 - Hole spacing min. 31 mm / min. 25 mm by using of the rectangular front protectice cap 61-9927.2 41 01.2010 51 Drawings 4 Front bezel set for Mushroom-head pushbutton, flush mounting page 25 O32 = 32 min. +0.4 0 O 32 mm 22.3 O40 = 40 min. O 40 mm O40 = 40 min. O32 = 35 min. Technical drawing 2.8 x 0.5 1 Keylock switch 3 positions page 10 18 x 24 mm 1.5 ... 6 11.5 42 35 2 Protective cover, raised mounting page 27 20 25.5 23.5 10.5 32 14.5 3 Protective cover, raised mounting page 27 24 25.5 23.5 10.5 32 14.5 42 01.2010 18 x 18 mm O 18 mm 51 Drawings 2.8 x 0.5 4 Keylock switch actuator 3 positions, flush mounting page 18 24 x 30 mm 1.5 ... 5 3.5 24 x 24 mm O 25 mm 50 27 2.8 x 0.5 5 Selector switch actuator 3 positions, flush mounting page 20 1.5 ... 5 24 x 24 mm O 25 mm 2 9.5 50 2.8 x 0.5 6 Selector switch 3 positions page 12 1.5 ... 6 6 O 18 mm 42 14 43 01.2010 51 Drawings 7 Protective cover, flush mounting page 27 24 12 25 5.5 max. 24 4.5 8 Protective cover, flush mounting page 27 24 12 25 5.5 max. 30 4.5 9 Protective cover, flush mounting page 27 10 29.3 1.5 min. 42 5.5 max. O 25 50 14.5 4 10 Legend frame page 24 O25 23.5 30 11 Blind plug, flush mounting page 27 16.5 min. 20.5 max. 23.5 2 1...5 25 44 01.2010 51 Drawings 2.8 x 0.5 3 L1 10.5 O 18 mm U U+D Universal terminal + diodes 18 x 18 mm Universal terminal 18 x 24 mm Soldering terminal (also plugable) 1.5 ... 6 Soldering terminal 12 Indicator actuator page 7 L L1 U U+D 23 26 35 1D, 2D 35 L Universal terminal Combined terminal + diodes L L1 U H+D 1NC+1NO 28 36 - - 2NC+2NO 35.5 - - - 3NC+3NO 43 - - - 4NC+4NO Soldering terminal Soldering terminal (also pluggable) 13 Illuminated pushbutton actuator page 8 1.5 ... 6 18 x 24 mm 18 x 18 mm O 18 mm 2.8 x 0.5 3 L1 10.5 U H+D L 50.5 - - - 1NC+1NO+D - - - 43.5 2NO+2NC+D - - - 51 35 - 1NC, 1NO, 1NC+1NO, 2NC, 2NO L1 11.5 Universal terminal 18 x 18 mm Soldering terminal (also pluggable) 18 x 24 mm L L1 U 1NC+1NO 26.5 36 - 2NC+2NO 34 - - 3NC+3NO 41.5 - - 4NC+4NO 49 - O 18 mm 3 2.8 x 0.5 1.5 ... 6 Soldering terminal 14 Keylock switch 2 positions page 9 U 1NC, 1NO, 1NC+1NO, 2NC, 2NO 35.5 L 35 45 01.2010 51 Drawings O 25 mm 3 L1 2 U Universal terminal 24 x 24 mm 2.8 x 0.5 24 x 30 mm Soldering terminal 1.5 ... 4 Soldering terminal (also pluggable) 15 Indicator actuator, flush mounting page 13 L L1 U 31 34 44 L L L1 U 1NC+1NO 36.5 44 - 2NC+2NO 44 - - 3NC+3NO 51.5 - - 4NC+4NO 59 - O 25 mm 3 L1 2 Universal termnal 24 x 24 mm 2.8 x 0.5 24 x 30 mm Soldering terminal (also pluggable) 1.5 ... 4 Soldering terminal 16 Illuminated pushbutton actuator, flush mounting page 14 - 1NC, 1NO, 1NC+1NO, 2NC, 2NO U 44 L L1 3.5 L 27 46 01.2010 Universal terminal 24 x 24 mm Soldering terminal (also pluggable) 24 x 30 mm L L1 U 1NC+1NO 35 44.5 - 2NC+2NO 42.5 - - 3NC+3NO 50 - - 4NC+4NO 57.5 - O 25 mm 3 2.8 x 0.5 1.5 ... 5 Soldering terminal 17 Keylock switch actuator 2 positions, flush mounting page 15 U 1NC, 1NO, 1NC+1NO, 2NC, 2NO 44.5 51 Drawings Universal terminal 24 x 24 mm Soldering terminal (also pluggable) 1.5 ... 6 Soldering terminal 18 Selector switch actuator 2 positions, flush mounting page 19 L L1 U 1NC+1NO 41 48 - 2NC+2NO 48.5 - - 3NC+3NO 56 - - 4NC+4NO 63.5 - O 25 mm 2.8 x 0.5 3 L1 U - 1NC, 1NO, 1NC+1NO, 2NC, 2NO 48 2 9.5 L Universal terminal Combined terminal + diodes L L1 U H+D 1NC+1NO 32 36 - - 2NC+2NO 39.5 - - - 3NC+3NO 47 - - - 4NC+4NO Soldering terminal Soldering terminal (also pluggable) 19 Selector switch 2 positions page 11 1.5 ... 6 18 x 24 mm 18 x 18 mm 2.8 x 0.5 3 L1 6 O 18 mm U L H+D 54.5 - - - 1NC+1NO+D - - - 43.5 2NC+2NO+D - - - 51 39 - 1NC, 1NO, 1NC+1NO, 2NC, 2NO 14 Circuit drawing 1 Indicator actuator page 7 | Indicator actuator, flush mounting page 13 a-(x1) b+(x2) 2 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14 1 3 1 2 3 1 4 2 3 1 4 2 3 x1- 4 x2+ IV III II I 4 2 3 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14 1 3 1 2 3 1 4 2 3 x1- 4 x2+ III II I 4 2 47 01.2010 51 Drawings 4 Illuminated pushbutton actuator page 8 1 3 1 I 2 3 a- 3(+) 4 b+ 4(-) II 2 4 5 Illuminated pushbutton actuator page 8 1 3 1 I 2 3 a- 3(+) 1(-) 4 b+ 4(-) 2(+) II 2 4 6 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14 1 1 3 2 3 x1- 4 x2+ II I 2 4 7 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14 1 3 a- 4 b+ I 2 8 Illuminated pushbutton actuator page 8 1 3 a- 3(+) 4 b+ 4(-) I 2 9 Illuminated pushbutton actuator page 8 1 3 a- 3(+) 1(-) 4 b+ 4(-) 2(+) I 2 10 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14 1 3 x1- 4 x2+ I 2 11 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14 1 a- 2 b+ 48 01.2010 51 Drawings 12 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14 1 3 a- 2 4 b+ 13 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14 1 a- 2 b+ 14 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14 1 3 a- 2 4 b+ 15 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14 1 3 a- 2 4 b+ 16 Selector switch 3 positions page 12 | Selector switch actuator 3 positions, flush mounting page 20 1 3 1 2 3 a- 4 b+ B C 4 2 17 Selector switch 3 positions page 12 | Selector switch actuator 3 positions, flush mounting page 20 1 3 1 2 3 a- 4 b+ B C 4 2 18 Selector switch 3 positions page 12 | Selector switch actuator 3 positions, flush mounting page 20 1 3 1 2 3 a- 4 b+ B C 4 2 19 Selector switch 3 positions page 12 | Selector switch actuator 3 positions, flush mounting page 20 1 3 1 2 3 a- 4 b+ B C 4 2 49 01.2010 51 Drawings 20 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19 1 3 1 I 2 3 1 II 2 4 3 1 III 2 4 3 x1- 4 x2+ IV 2 4 21 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19 1 3 1 I 2 3 1 II 2 4 3 x1- 4 x2+ III 2 4 22 Selector switch 2 positions page 11 1 1 3 2 3 a- 3(+) 4 b+ 4(-) 3 a- 3(+) 1(-) 4 b+ 4(-) 2(+) II I 2 4 23 Selector switch 2 positions page 11 1 1 3 II I 2 2 4 24 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19 1 1 3 2 3 x1- 4 x2+ II I 2 4 25 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19 1 3 a- 4 b+ I 2 26 Selector switch 2 positions page 11 1 3 a- 3(+) 4 b+ 4(-) I 2 27 Selector switch 2 positions page 11 1 3 a- 3(+) 1(-) 4 b+ 4(-) 2(+) I 2 50 01.2010 51 Drawings 28 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19 1 3 x1- 4 x2+ I 2 29 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19 1 a- 2 b+ 30 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19 1 3 a- 2 4 b+ 31 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19 1 a- 2 b+ 32 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19 1 3 a- 2 4 b+ 33 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19 1 3 a- 2 4 b+ 34 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19 1 3 1 2 3 1 4 2 3 1 4 2 3 x1- 4 x2+ IV III II I 4 2 35 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19 1 3 1 2 3 1 4 2 3 x1- 4 x2+ III II I 4 2 51 01.2010 51 Drawings 36 Selector switch 2 positions page 11 1 3 1 I 2 3 a- 3(+) 4 b+ 4(-) 3 a- 3(+) 1(-) 4 b+ 4(-) 2(+) II 2 4 37 Selector switch 2 positions page 11 1 3 1 I 2 II 2 4 38 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19 1 1 3 2 3 x1- 4 x2+ II I 2 4 39 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19 1 3 a- 4 b+ I 2 40 Selector switch 2 positions page 11 1 3 a- 3(+) 4 b+ 4(-) I 2 41 Selector switch 2 positions page 11 1 3 a- 3(+) 1(-) 4 b+ 4(-) 2(+) I 2 42 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19 1 3 x1- 4 x2+ I 2 43 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19 52 01.2010 1 a- 2 b+ 51 Drawings 44 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19 1 3 a- 2 4 b+ 45 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19 1 a- 2 b+ 46 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19 1 3 a- 2 4 b+ 47 Selector switch 2 positions page 11 | Selector switch actuator 2 positions, flush mounting page 19 1 3 a- 2 4 b+ 48 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14 1 3 1 2 1 3 4 2 1 3 2 4 3 x1- 4 x2+ IV III II I 2 4 49 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14 1 3 1 2 1 3 4 2 3 x1- 4 x2+ III II I 2 4 50 Illuminated pushbutton actuator page 8 1 3 1 2 3 a- 3(+) 4 b+ 4(-) II I 4 2 51 Illuminated pushbutton actuator page 8 1 3 1 2 3 a- 3(+) 1(-) 4 b+ 4(-) 2(+) II I 4 2 53 01.2010 51 Drawings 52 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14 1 3 1 I 2 3 x1- 4 x2+ II 2 4 53 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14 1 3 x1- 4 x2+ I 2 54 Illuminated pushbutton actuator page 8 1 3 a- 3(+) 4 b+ 4(-) I 2 55 Illuminated pushbutton actuator page 8 1 3 a- 3(+) 1(-) 4 b+ 4(-) 2(+) I 2 56 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14 1 3 x1- 4 x2+ I 2 57 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14 1 a- 2 b+ 58 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14 1 3 a- 2 4 b+ 59 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14 1 a- 2 b+ 54 01.2010 51 Drawings 60 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14 1 3 a- 2 4 b+ 61 Illuminated pushbutton actuator page 8 | Illuminated pushbutton actuator, flush mounting page 14 1 3 a- 2 4 b+ 62 Keylock switch 3 positions page 10 | Keylock switch actuator 3 positions, flush mounting page 18 1 1 3 2 3 B C 2 4 4 63 Keylock switch 3 positions page 10 | Keylock switch actuator 3 positions, flush mounting page 18 1 1 3 2 3 B C 2 4 4 64 Keylock switch 3 positions page 10 | Keylock switch actuator 3 positions, flush mounting page 18 1 1 3 2 3 B C 2 4 4 65 Keylock switch 3 positions page 10 | Keylock switch actuator 3 positions, flush mounting page 18 1 1 3 2 3 B C 2 4 4 66 Keylock switch 2 positions page 9 | Keylock switch actuator 2 positions, flush mounting page 15 1 3 I 2 4 67 Keylock switch 2 positions page 9 | Keylock switch actuator 2 positions, flush mounting page 15 1 3 1 2 3 II I 4 2 4 55 01.2010 51 Drawings 68 Keylock switch 2 positions page 9 | Keylock switch actuator 2 positions, flush mounting page 15 1 3 1 I 2 3 1 II 4 2 3 III 4 2 4 69 Keylock switch 2 positions page 9 | Keylock switch actuator 2 positions, flush mounting page 15 1 3 1 I 2 3 1 II 4 2 3 1 III 4 2 3 IV 4 2 4 70 Keylock switch 2 positions page 9 | Keylock switch actuator 2 positions, flush mounting page 15 1 3 2 4 71 Keylock switch 2 positions page 9 | Keylock switch actuator 2 positions, flush mounting page 15 1 3 2 4 72 Keylock switch 2 positions page 9 | Keylock switch actuator 2 positions, flush mounting page 15 1 3 I 2 4 73 Keylock switch 2 positions page 9 | Keylock switch actuator 2 positions, flush mounting page 15 1 3 1 2 3 II I 4 2 4 74 Keylock switch 2 positions page 9 | Keylock switch actuator 2 positions, flush mounting page 15 1 3 1 2 3 1 4 2 3 III II I 4 2 4 75 Keylock switch 2 positions page 9 | Keylock switch actuator 2 positions, flush mounting page 15 1 3 1 2 56 01.2010 3 1 4 2 3 1 4 2 3 IV III II I 4 2 4 51 Drawings 76 Keylock switch 2 positions page 9 | Keylock switch actuator 2 positions, flush mounting page 15 1 3 2 4 77 Keylock switch 2 positions page 9 | Keylock switch actuator 2 positions, flush mounting page 15 1 3 2 4 78 Indicator actuator page 7 a-(x1) 3(+) b+(x2) 4(-) 79 Indicator actuator page 7 a-(x1) 3(+) 1(-) b+(x2) 4(-) 2(+) 57 01.2010 Index from Typ-Nr. Typ-Nr. Page 01-907 ........................................31 01-928 ........................................29 01-929 ........................................29 02-904.0 .....................................30 02-904.1 .....................................30 02-904.3 .....................................30 02-904.7 .....................................30 02-905 ........................................31 02-912.1 .....................................30 02-912.2 .....................................30 02-912.3 .....................................30 02-912.4 .....................................30 10-1306.1349 .............................29 10-1307.1369 .............................29 10-1309.1309 .............................29 10-1310.1319 .............................29 10-1311.1249 .............................29 10-1312.1229 .............................29 10-1313.1209 .............................29 10-1313.1249 .............................29 10-1316.1179 .............................29 10-1316.1209 .............................29 10-1319.1179 .............................29 10-1319.1199 .............................29 10-2J06.3142 .............................30 10-2J06.3144 .............................30 10-2J06.3145 .............................30 10-2J06.3146 .............................30 10-2J06.3149 .............................30 10-2J09.1062 .............................30 10-2J09.1064 .............................30 10-2J09.1065 .............................30 10-2J09.1066 .............................30 10-2J09.1069 .............................30 10-2J12.1062 .............................30 10-2J12.1064 .............................30 10-2J12.1065 .............................30 10-2J12.1066 .............................30 10-2J12.1069 .............................30 10-2J13.1062 .............................30 10-2J13.1064 .............................30 10-2J13.1065 .............................30 10-2J13.1066 .............................30 10-2J13.1069 .............................30 10-2J19.1042 .............................30 10-2J19.1044 .............................30 10-2J19.1045 .............................30 10-2J19.1046 .............................30 10-2J19.1049 .............................30 31-928 ........................................29 31-929 ........................................29 31-940 ........................................28 31-941 ........................................28 31-942 ........................................28 31-945 ........................................29 31-946 ........................................29 31-985.0 .....................................28 31-989.300 .................................28 31-989.311 .................................28 31-991 ........................................31 51-030.002 ...................................7 51-030.005 ...................................7 51-031.006 ...................................7 58 01.2010 Typ-Nr. Page 51-040.002 ...................................7 51-040.005 ...................................7 51-041.006 ...................................7 51-050.002 ...................................7 51-050.002F ...............................13 51-050.005 ...................................7 51-050.005F ...............................13 51-051.006 ...................................7 51-051.006F ...............................13 51-121.022 ...................................8 51-121.0252 .................................8 51-122.0252 .................................8 51-123.0252 .................................8 51-124.0252 .................................8 51-131.022 ...................................8 51-131.0252 .................................8 51-132.0252 .................................8 51-133.0252 .................................8 51-134.0252 .................................8 51-135.022D .................................9 51-135.022DF ............................16 51-135.025D2 ...............................9 51-135.025D2F ..........................16 51-136.025D2 ...............................9 51-136.025D2F ..........................16 51-137.025D2 ...............................9 51-137.025D2F ..........................16 51-138.025D2 ...............................9 51-138.025D2F ..........................16 51-141.022D .................................9 51-141.022DF ............................17 51-141.025D2 ...............................9 51-141.025D2F ..........................17 51-142.025D2 ...............................9 51-142.025D2F ..........................17 51-143.025D2 ...............................9 51-143.025D2F ..........................17 51-144.025D2 ...............................9 51-144.025D2F ..........................17 51-145.022D .................................9 51-145.022DF ............................15 51-145.025D2 ...............................9 51-145.025D2F ..........................15 51-146.025D2 ...............................9 51-146.025D2F ..........................15 51-147.025D2 ...............................9 51-147.025D2F ..........................15 51-148.025D2 ...............................9 51-148.025D2F ..........................15 51-151.022 ...................................8 51-151.022F ...............................14 51-151.0252 .................................8 51-151.0252F .............................14 51-152.0252 .................................8 51-152.0252F .............................14 51-153.0252 .................................8 51-153.0252F .............................14 51-154.0252 .................................8 51-154.0252F .............................14 51-155.022D .................................9 51-155.022DF ............................15 51-155.025D2 ...............................9 51-155.025D2F ..........................15 Typ-Nr. Page 51-156.025D2 ...............................9 51-156.025D2F ..........................15 51-157.025D2 ...............................9 51-157.025D2F ..........................15 51-158.025D2 ...............................9 51-158.025D2F ..........................15 51-195.022D .................................9 51-195.022DF ............................16 51-195.025D2 ...............................9 51-195.025D2F ..........................16 51-196.025D2 ...............................9 51-196.025D2F ..........................16 51-197.025D2 ...............................9 51-197.025D2F ..........................16 51-198.025D2 ...............................9 51-198.025D2F ..........................16 51-235.022D .................................9 51-235.022DF ............................16 51-235.025D2 ...............................9 51-235.025D2F ..........................16 51-236.025D2 ...............................9 51-236.025D2F ..........................16 51-237.025D2 ...............................9 51-237.025D2F ..........................16 51-238.025D2 ...............................9 51-238.025D2F ..........................16 51-255.022D .................................9 51-255.022DF ............................15 51-255.025D2 ...............................9 51-255.025D2F ..........................15 51-256.025D2 ...............................9 51-256.025D2F ..........................15 51-257.025D2 ...............................9 51-257.025D2F ..........................15 51-258.025D2 ...............................9 51-258.025D2F ..........................15 51-261.022 ...................................8 51-261.0252 .................................8 51-262.0252 .................................8 51-263.0252 .................................8 51-264.0252 .................................8 51-271.022 ...................................8 51-271.0252 .................................8 51-272.0252 .................................8 51-273.0252 .................................8 51-274.0252 .................................8 51-281.022 ...................................8 51-281.022F ...............................14 51-281.0252 .................................8 51-281.0252F .............................14 51-282.0252 .................................8 51-282.0252F .............................14 51-283.0252 .................................8 51-283.0252F .............................14 51-284.0252 .................................8 51-284.0252F .............................14 51-295.022D .................................9 51-295.022DF ............................16 51-295.025D2 ...............................9 51-295.025D2F ..........................16 51-296.025D2 ...............................9 51-296.025D2F ..........................16 51-297.025D2 ...............................9 Index from Typ-Nr. Typ-Nr. Page 51-297.025D2F .......................... 16 51-298.025D2 .............................. 9 51-298.025D2F .......................... 16 51-335.022D ................................ 9 51-335.022DF ............................ 16 51-335.025D2 .............................. 9 51-335.025D2F .......................... 16 51-336.025D2 .............................. 9 51-336.025D2F .......................... 16 51-337.025D2 .............................. 9 51-337.025D2F .......................... 16 51-338.025D2 .............................. 9 51-338.025D2F .......................... 16 51-355.022D ................................ 9 51-355.022DF ............................ 15 51-355.025D2 .............................. 9 51-355.025D2F .......................... 15 51-356.025D2 .............................. 9 51-356.025D2F .......................... 15 51-357.025D2 .............................. 9 51-357.025D2F .......................... 15 51-358.025D2 .............................. 9 51-358.025D2F .......................... 15 51-361.022D .............................. 10 51-361.022DF ............................ 18 51-362.022D .............................. 10 51-362.022DF ............................ 18 51-363.022D .............................. 10 51-363.022DF ............................ 18 51-364.022D .............................. 10 51-364.022DF ............................ 18 51-365.022D .............................. 10 51-365.022DF ............................ 18 51-366.022D .............................. 10 51-366.022DF ............................ 18 51-367.022D .............................. 10 51-367.022DF ............................ 18 51-368.022D .............................. 10 51-368.022DF ............................ 18 51-371.022D .............................. 10 51-371.022DF ............................ 18 51-372.022D .............................. 10 51-372.022DF ............................ 18 51-373.022D .............................. 10 51-373.022DF ............................ 18 51-374.022D .............................. 10 51-374.022DF ............................ 18 51-375.022D .............................. 10 51-375.022DF ............................ 18 51-376.022D .............................. 10 51-376.022DF ............................ 18 51-377.022D .............................. 10 51-377.022DF ............................ 18 51-378.022D .............................. 10 51-378.022DF ............................ 18 51-381.022D .............................. 10 51-381.022DF ............................ 18 51-382.022D .............................. 10 51-382.022DF ............................ 18 51-383.022D .............................. 10 51-383.022DF ............................ 18 51-384.022D .............................. 10 51-384.022DF ............................ 18 Typ-Nr. Page 51-385.022D .............................. 10 51-385.022DF ............................ 18 51-386.022D .............................. 10 51-386.022DF ............................ 18 51-387.022D .............................. 10 51-387.022DF ............................ 18 51-388.022D .............................. 10 51-388.022DF ............................ 18 51-395.022D ................................ 9 51-395.022DF ............................ 16 51-395.025D2 .............................. 9 51-395.025D2F .......................... 16 51-396.025D2 .............................. 9 51-396.025D2F .......................... 16 51-397.025D2 .............................. 9 51-397.025D2F .......................... 16 51-398.025D2 .............................. 9 51-398.025D2F .......................... 16 51-401.036D ................................ 9 51-401.036DF ............................ 16 51-402.036D ................................ 9 51-402.036DF ............................ 16 51-404.036D ................................ 9 51-404.036DF ............................ 16 51-405.036D ................................ 9 51-405.036DF ............................ 16 51-407.036D ................................ 9 51-407.036DF ............................ 16 51-408.036D ................................ 9 51-408.036DF ............................ 16 51-411.036D ................................ 9 51-411.036DF ............................ 16 51-412.036D ................................ 9 51-412.036DF ............................ 16 51-414.036D ................................ 9 51-414.036DF ............................ 16 51-415.036D ................................ 9 51-415.036DF ............................ 16 51-417.036D ................................ 9 51-417.036DF ............................ 16 51-418.036D ................................ 9 51-418.036DF ............................ 16 51-421.036 ................................... 8 51-422.036 ................................... 8 51-423.036 ................................... 8 51-425.036 ................................... 8 51-426.036 ................................... 8 51-427.036D ................................ 9 51-427.036DF ............................ 16 51-428.036D ................................ 9 51-428.036DF ............................ 16 51-431.036 ................................... 8 51-432.036 ................................... 8 51-433.036 ................................... 8 51-435.036 ................................... 8 51-436.036 ................................... 8 51-437.036D ................................ 9 51-437.036DF ............................ 17 51-438.036D ................................ 9 51-438.036DF ............................ 17 51-441.036D ................................ 9 51-441.036DF ............................ 15 51-442.036D ................................ 9 Typ-Nr. Page 51-442.036DF ............................ 15 51-444.036D ................................9 51-444.036DF ............................ 15 51-445.036D ................................9 51-445.036DF ............................ 15 51-447.036D ................................9 51-447.036DF ............................ 15 51-448.036D ................................9 51-448.036DF ............................ 15 51-451.036 ...................................8 51-451.036F ............................... 14 51-452.036 ...................................8 51-452.036F ............................... 14 51-453.036 ...................................8 51-453.036F ............................... 14 51-455.036 ...................................8 51-455.036F ............................... 14 51-456.036 ...................................8 51-456.036F ............................... 14 51-457.036D ................................9 51-457.036DF ............................ 15 51-458.036D ................................9 51-458.036DF ............................ 15 51-461.036 ...................................8 51-462.036 ...................................8 51-463.036 ...................................8 51-465.036 ...................................8 51-466.036 ...................................8 51-471.036 ...................................8 51-472.036 ...................................8 51-473.036 ...................................8 51-475.036 ...................................8 51-476.036 ...................................8 51-481.036 ...................................8 51-481.036F ............................... 14 51-482.036 ...................................8 51-482.036F ............................... 14 51-483.036 ...................................8 51-483.036F ............................... 14 51-485.036 ...................................8 51-485.036F ............................... 14 51-486.036 ...................................8 51-486.036F ............................... 14 51-495.022D ................................9 51-495.022DF ............................ 16 51-495.025D2 .............................. 9 51-495.025D2F .......................... 16 51-496.025D2 .............................. 9 51-496.025D2F .......................... 16 51-497.025D2 .............................. 9 51-497.025D2F .......................... 16 51-498.025D2 .............................. 9 51-498.025D2F .......................... 16 51-701.006 ...................................7 51-702.006 ...................................7 51-703.006 ...................................7 51-704.006 ...................................7 51-705.0292 ................................. 8 51-706.0292 ................................. 8 51-707.0292 ................................. 8 51-708.0292 ................................. 8 51-709.0292 ................................. 8 51-710.0292 ................................. 8 59 01.2010 Index from Typ-Nr. Typ-Nr. Page 51-711.0292 .................................8 51-712.0292 .................................8 51-713.0292 .................................8 51-714.0292 .................................8 51-715.0292 .................................8 51-716.0292 .................................8 51-717.0292 .................................8 51-718.0292 .................................8 51-719.0292 .................................8 51-720.0292 .................................8 51-741.006 ...................................7 51-742.006 ...................................7 51-743.0292 .................................8 51-744.0292 .................................8 51-745.0292 .................................8 51-746.0292 .................................8 51-747.0292 .................................8 51-748.0292 .................................8 51-749.0292 .................................8 51-750.0292 .................................8 51-901.0 .....................................21 51-901.2 .....................................21 51-901.3 .....................................21 51-901.4 .....................................21 51-901.5 .....................................21 51-901.6 .....................................21 51-901.8 .....................................21 51-901.9 .....................................21 51-903.1 .....................................21 51-903.2 .....................................21 51-903.3 .....................................21 51-903.4 .....................................21 51-903.5 .....................................21 51-903.6 .....................................21 51-903.7 .....................................21 51-904.2 .....................................21 51-904.3 .....................................21 51-904.4 .....................................21 51-904.5 .....................................21 51-904.6 .....................................21 51-904.7 .....................................21 51-905.2 .....................................21 51-905.4 .....................................21 51-905.5 .....................................21 51-905.7 .....................................21 51-906.2 .....................................21 51-906.4 .....................................21 51-906.5 .....................................21 51-906.7 .....................................21 51-910 ........................................31 51-920 ........................................27 51-925 ........................................27 51-931.0 .....................................21 51-931.2 .....................................21 51-931.3 .....................................21 51-931.4 .....................................21 51-931.5 .....................................21 51-931.6 .....................................21 51-931.8 .....................................21 51-931.9 .....................................21 51-933.1 .....................................21 51-933.2 .....................................21 51-933.3 .....................................21 60 01.2010 Typ-Nr. Page 51-933.4 .....................................21 51-933.5 .....................................21 51-933.6 .....................................21 51-933.7 .....................................21 51-935.2 .....................................21 51-935.4 .....................................21 51-935.5 .....................................21 51-935.7 .....................................21 51-938 ........................................31 51-943.0 .....................................28 51-943.1 .....................................29 51-943.9 .....................................32 51-947.0 .....................................27 51-948.0 .....................................27 51-949.0 .....................................27 51-951.0 .....................................21 51-951.2 .....................................21 51-951.3 .....................................21 51-951.4 .....................................21 51-951.5 .....................................21 51-951.6 .....................................21 51-951.8 .....................................21 51-951.9 .....................................21 51-953.1 .....................................21 51-953.2 .....................................21 51-953.3 .....................................21 51-953.4 .....................................21 51-953.5 .....................................21 51-953.6 .....................................21 51-953.7 .....................................21 51-954.2 .....................................21 51-954.3 .....................................21 51-954.4 .....................................21 51-954.5 .....................................21 51-954.6 .....................................21 51-954.7 .....................................21 51-955.2 .....................................21 51-955.4 .....................................21 51-955.5 .....................................21 51-955.7 .....................................21 52-131.022 .................................11 52-131.022 .................................19 52-131.0252 ...............................11 52-131.0252 ...............................19 52-132.0252 ...............................11 52-132.0252 ...............................19 52-133.0252 ...............................11 52-133.0252 ...............................19 52-134.0252 ...............................11 52-134.0252 ...............................19 52-271.022 .................................11 52-271.022 .................................19 52-271.0252 ...............................11 52-271.0252 ...............................19 52-272.0252 ...............................11 52-272.0252 ...............................19 52-273.0252 ...............................11 52-273.0252 ...............................19 52-274.0252 ...............................11 52-274.0252 ...............................19 52-431.036 .................................11 52-431.036 .................................19 52-432.036 .................................11 Typ-Nr. Page 52-432.036 .................................19 52-433.036 .................................11 52-433.036 .................................19 52-435.036 .................................11 52-435.036 .................................19 52-436.036 .................................11 52-436.036 .................................19 52-471.036 .................................11 52-471.036 .................................19 52-472.036 .................................11 52-472.036 .................................19 52-473.036 .................................11 52-473.036 .................................19 52-475.036 .................................11 52-475.036 .................................19 52-476.036 .................................11 52-476.036 .................................19 52-571.022A ...............................12 52-571.022A ...............................20 52-572.022A ...............................12 52-572.022A ...............................20 52-573.022A ...............................12 52-573.022A ...............................20 52-574.022A ...............................12 52-574.022A ...............................20 52-743.0292 ...............................11 52-744.0292 ...............................11 52-745.0292 ...............................11 52-746.0292 ...............................11 52-747.0292 ...............................11 52-748.0292 ...............................11 52-749.0292 ...............................11 52-750.0292 ...............................11 52-928.0 .....................................24 52-928.20 ...................................24 52-928.30 ...................................24 52-928.40 ...................................24 52-928.50 ...................................24 52-928.60 ...................................24 52-929.20 ...................................24 52-929.30 ...................................24 52-929.40 ...................................24 52-929.50 ...................................24 52-929.60 ...................................24 52-929.8 .....................................24 52-929.9 .....................................24 52-950.0 .....................................23 52-952.0 .....................................23 61-9028.0 ...................................24 61-9028.20 .................................24 61-9028.30 .................................24 61-9028.40 .................................24 61-9028.50 .................................24 61-9028.60 .................................24 61-9028.9 ...................................24 61-9029.20 .................................24 61-9029.30 .................................24 61-9029.40 .................................24 61-9029.50 .................................24 61-9029.60 .................................24 61-9029.8 ...................................24 61-9029.9 ...................................24 61-9451.0 ...................................27 Index from Typ-Nr. Typ-Nr. Page 61-9452.0 ................................... 27 61-9453.0 ................................... 27 61-9593.0 ................................... 23 61-9593.2 ................................... 23 61-9593.4 ................................... 23 61-9593.5 ................................... 23 61-9642.1 ................................... 21 61-9642.2 ................................... 21 61-9642.3 ................................... 21 61-9642.4 ................................... 21 61-9642.5 ................................... 21 61-9642.6 ................................... 21 61-9642.7 ................................... 21 61-9643.201 ............................... 22 61-9643.202 ............................... 22 61-9643.203 ............................... 22 61-9643.301 ............................... 22 61-9643.401 ............................... 22 61-9643.501 ............................... 22 61-9643.502 ............................... 22 61-9643.503 ............................... 22 61-9643.601 ............................... 22 61-9643.602 ............................... 22 61-9643.603 ............................... 22 61-9643.701 ............................... 22 61-9643.702 ............................... 22 61-9643.703 ............................... 22 61-9671.1 ................................... 21 61-9671.2 ................................... 21 61-9671.3 ................................... 21 61-9671.4 ................................... 21 61-9671.5 ................................... 21 61-9671.6 ................................... 21 61-9671.7 ................................... 21 61-9681.1 ................................... 21 61-9681.2 ................................... 21 61-9681.3 ................................... 21 61-9681.4 ................................... 21 61-9681.5 ................................... 21 61-9681.6 ................................... 21 61-9681.7 ................................... 21 61-9707.7 ................................... 22 61-9730.0 ................................... 31 61-9740.0 ................................... 31 61-9771.0 ................................... 21 61-9771.8 ................................... 21 61-9771.9 ................................... 21 61-9781.0 ................................... 21 61-9781.8 ................................... 21 61-9781.9 ................................... 21 61-9841.0 ................................... 23 61-9841.0A ................................ 22 61-9841.2 ................................... 23 61-9841.2A ................................ 22 61-9841.4 ................................... 23 61-9841.4A ................................ 22 61-9841.5 ................................... 23 61-9841.5A ................................ 22 61-9841.6 ................................... 23 61-9841.6A ................................ 22 61-9841.8 ................................... 23 61-9841.8A ................................ 22 61-9842.0 ................................... 23 Typ-Nr. Page Typ-Nr. Page 61-9842.2 ................................... 23 61-9842.4 ................................... 23 61-9842.5 ................................... 23 61-9842.6 ................................... 23 61-9842.8 ................................... 23 61-9921.0 ................................... 27 61-9922.0 ................................... 27 61-9924.0 ................................... 27 61-9927.2 ................................... 26 61-9930.0 ................................... 25 61-9930.0 ................................... 26 61-9930.4 ................................... 25 61-9930.4 ................................... 26 61-9931.0 ................................... 25 61-9931.0 ................................... 26 61-9931.4 ................................... 25 61-9931.4 ................................... 26 61-9932.0 ................................... 26 61-9932.0 ................................... 26 61-9932.1 ................................... 26 61-9932.1 ................................... 26 61-9932.10 ................................. 26 61-9932.10 ................................. 26 61-9932.2 ................................... 26 61-9932.2 ................................... 26 61-9932.4 ................................... 26 61-9932.4 ................................... 26 61-9932.5 ................................... 26 61-9932.5 ................................... 26 61-9932.6 ................................... 26 61-9932.6 ................................... 26 61-9933.0 ................................... 25 61-9933.0 ................................... 25 61-9933.1 ................................... 25 61-9933.1 ................................... 25 61-9933.10 ................................. 25 61-9933.10 ................................. 25 61-9933.2 ................................... 25 61-9933.2 ................................... 25 61-9933.4 ................................... 25 61-9933.4 ................................... 25 61-9933.5 ................................... 25 61-9933.5 ................................... 25 61-9933.6 ................................... 25 61-9933.6 ................................... 25 61-9934.8 ................................... 25 61-9936.0 ................................... 26 61-9980.0 ................................... 24 704.968.0 ................................... 25 704.968.1 ................................... 25 84-9103.7 ................................... 26 61 01.2010 Phone Fax E-mail Phone Fax E-mail Phone Fax E-mail Phone Fax E-mail Phone Fax E-mail Phone Fax E-mail Phone Fax E-mail Phone Fax E-mail Phone Fax E-mail Phone Fax E-mail Phone Fax E-mail Phone Fax E-mail Phone Fax E-mail EAO reserves the right to alter specifications without further notice E-mail Website EAO AG Tannwaldstrasse 88 4601 Olten, Switzerland info@eao.com www.eao.com Austria +49 201 85 87 0 +49 201 85 87 210 sales.ede@eao.com Belgium +32 3 777 82 36 +32 3 777 84 19 sales.ebl@eao.com China +852 27 86 91 41 +852 27 86 95 61 sales.ehk@eao.com France +33 1 64 43 37 37 +33 1 64 43 37 49 sales.ese@eao.com Germany +49 201 85 87 0 +49 201 85 87 210 sales.ede@eao.com Italy +39 035 481 0189 +39 035 481 3786 sales.eit@eao.com Japan +81 3 5444 5411 +81 3 5444 0345 sales.esj@eao.com Netherlands +31 78 653 17 00 +31 78 653 17 99 sales.enl@eao.com Sweden +46 8 683 86 60 +46 8 724 29 12 sales.esw@eao.com Switzerland +41 62 388 95 00 +41 62 388 95 55 sales.ech@eao.com United Kingdom +44 1444 236 000 +44 1444 236 641 sales.euk@eao.com USA +1 203 877 4577 +1 203 877 3694 sales.eus@eao.com Other Countries +41 62 286 92 10 +41 62 296 21 62 info@eao.com