GS1531 HD-LINX(R) II Multi-Rate Serializer with ClockCleanerTM GS1531 Data Sheet Key Features Description * SMPTE 292M and SMPTE 259M-C compliant scrambling and NRZ NRZI encoding (with bypass) * DVB-ASI sync word insertion and 8b/10b encoding * Rejection of more than 300ps jitter on the input PCLK The GS1531 is a multi-standard serializer with an integrated cable driver. When used in conjunction with the GO1555/GO1525* Voltage Controlled Oscillator, a transmit solution can be realized for HD-SDI, SD-SDI and DVB-ASI applications. * User selectable additional processing features including: * CRC, ANC data checksum, and line number calculation and insertion * TRS and EDH packet generation and insertion * illegal code remapping * Internal flywheel for noise immune TRS generation * 20-bit / 10-bit CMOS parallel input data bus * 148.5MHz / 74.25MHz / 27MHz / 13.5MHz parallel digital input * Automatic standards detection and indication * 1.8V core power supply and 3.3V charge pump power supply * 3.3V digital I/O supply * JTAG test interface * Available in a Pb-free package * small footprint (11mm x 11mm) Applications * SMPTE 292M Serial Digital Interfaces * SMPTE 259M-C Serial Digital Interfaces * DVB-ASI Serial Digital Interfaces The device features an internal PLL, which can be configured for loop bandwidth as narrow as 100kHz. Thus the GS1531 can tolerate in excess of 300ps jitter on the input PCLK and still provide output jitter well within SMPTE specification. Connect the output clocks from Gennum's GS4911 clock generator directly to the GS1531's PCLK input and configure the GS1531's loop bandwidth accordingly. In addition to serializing the input, the GS1531 performs NRZ-to-NRZI encoding and scrambling as per SMPTE 292M/259M-C when operating in SMPTE mode. When operating in DVB-ASI mode, the device will insert K28.5 sync characters and 8b/10b encode the data prior to serialization. Parallel data inputs are provided for 10-bit multiplexed or 20-bit demultiplexed formats at both HD and SD signal rates. An appropriate parallel clock input signal is also required. The integrated cable driver features an output mute on loss of parallel clock, high impedance mode, adjustable signal swing, and automatic dual slew rate selection depending on HD/SD operational requirements. The GS1531 also includes a range of data processing functions including automatic standards detection and EDH support. The device can also insert TRS signals, calculate and insert line numbers and CRC's, re-map illegal code words and insert SMPTE 352M payload identifier packets. All processing features are optional and may be enabled/disabled via external control pin(s) and/or host interface programming. *For new designs use GO1555 30573 - 7 February 2008 1 of 50 www.gennum.com GS1531 Data Sheet Functional Block Diagram VCO_GND LF VCO_VCC LB_CONT VCO VCO CP_CAP PCLK LOCKED F V H DETECT_TRS DVB_ASI IOPROC_EN/DIS SMPTE_BYPASS BLANK SD/HD 20bit/10bit Phase detector, charge pump, VCO control & power supply HOST Interface / JTAG test sd/hd bypass DIN[19:0] TRS insertion, Line number insertion, CRC insertion, data blank, codere-map and flywheel I/O Buffer & demux dvb-asi ClockCleanerTM SDO_EN/DIS DVB-ASI sync word insert & 8b/10b encode SMPTE 352M generation EDH generation & SMPTE scramble SDO P -> S SDO RSET Reset RESET_TRST SDOUT_TDO SDIN_TDI SCLK_TCK CS_TMS JTAG/HOST GS1531 Functional Block Diagram 30573 - 7 February 2008 2 of 50 GS1531 Data Sheet Contents Key Features .................................................................................................................1 Applications...................................................................................................................1 Description ....................................................................................................................1 Functional Block Diagram .............................................................................................2 1. Pin Out .....................................................................................................................5 1.1 Pin Assignment ...............................................................................................5 1.2 Pin Descriptions ..............................................................................................6 2. Electrical Characteristics ........................................................................................13 2.1 Absolute Maximum Ratings ..........................................................................13 2.2 DC Electrical Characteristics ........................................................................13 2.3 AC Electrical Characteristics.........................................................................14 2.4 Solder Reflow Profiles...................................................................................16 3. Input/Output Circuits ..............................................................................................17 3.1 Host Interface Maps ......................................................................................19 3.1.1 Host Interface Map (Read Only Registers) .........................................20 3.1.2 Host Interface Map (R/W Configurable Registers) .............................21 4. Detailed Description ...............................................................................................22 4.1 Functional Overview .....................................................................................22 4.2 Parallel Data Inputs.......................................................................................22 4.2.1 Parallel Input in SMPTE Mode............................................................23 4.2.2 Parallel Input in DVB-ASI Mode..........................................................23 4.2.3 Parallel Input in Data-Through Mode ..................................................23 4.2.4 Parallel Input Clock (PCLK) ................................................................24 4.3 SMPTE Mode................................................................................................25 4.3.1 Internal Flywheel.................................................................................25 4.3.2 HVF Timing Signal Extraction .............................................................25 4.4 DVB-ASI mode..............................................................................................26 4.4.1 Control Signal Inputs ..........................................................................27 4.5 Data-Through Mode ......................................................................................28 4.6 Additional Processing Functions...................................................................28 4.6.1 Input Data Blank .................................................................................28 4.6.2 Automatic Video Standard Detection..................................................28 4.6.3 Packet Generation and Insertion ........................................................30 4.7 Parallel-To-Serial Conversion .......................................................................37 4.8 Serial Digital Data PLL..................................................................................38 4.8.1 External VCO......................................................................................38 4.8.2 Lock Detect Output .............................................................................38 4.8.3 Loop Bandwidth Adjustment ...............................................................39 4.9 Serial Digital Output ......................................................................................39 4.9.1 Output Swing ......................................................................................39 30573 - 7 February 2008 3 of 50 GS1531 Data Sheet 4.9.2 Serial Digital Output Mute...................................................................40 4.10 GSPI Host Interface ....................................................................................40 4.10.1 Command Word Description.............................................................41 4.10.2 Data Read and Write Timing ............................................................42 4.10.3 Configuration and Status Registers ..................................................43 4.11 JTAG...........................................................................................................43 4.12 Device Power Up ........................................................................................45 4.13 Device Reset...............................................................................................45 5. Application Reference Design ................................................................................46 5.1 Typical Application Circuit .............................................................................46 6. References & Relevant Standards.........................................................................47 7. Package & Ordering Information............................................................................48 7.1 Package Dimensions ....................................................................................48 7.2 Packaging Data.............................................................................................49 7.3 Ordering Information .....................................................................................49 8. Revision History .....................................................................................................50 30573 - 7 February 2008 4 of 50 GS1531 Data Sheet 1. Pin Out 1.1 Pin Assignment A B 1 2 3 4 5 6 LF VCO_ VCC VCO_ GND VCO VCO NC LB_ CONT NC NC NC CP_CAP CP_VDD CP_GND C NC D NC NC NC NC E NC NC NC SD/HD F RSV NC NC G NC NC NC H NC NC NC CS_ TMS J NC NC NC K RSET CD_VDD SDO 30573 - 7 PD_VDD PD_GND 8 9 10 PCLK IO_VDD DIN18 DIN19 NC DETECT _TRS IO_GND DIN16 DIN17 NC NC NC DIN14 DIN15 NC NC DIN12 DIN13 DVB_ASI LOCKED 7 CORE _GND CORE _VDD NC IO_VDD DIN10 DIN11 CORE _GND CORE _VDD NC IO_GND DIN8 DIN9 10bit IOPROC _EN/DIS SMPTE_ BYPASS RESET _TRST NC BLANK DIN6 DIN7 SCLK _TCK SDOUT _TDO NC H DIN4 DIN5 NC SDO_EN /DIS SDIN _TDI V IO_GND DIN2 DIN3 SD0 CD_GND JTAG/ HOST F IO_VDD DIN0 DIN1 20bit/ February 2008 5 of 50 GS1531 Data Sheet 1.2 Pin Descriptions Table 1-1: Pin Descriptions Pin Number Name Timing Type Description A1 LF Analog Output Control voltage to external voltage controlled oscillator. Nominally +1.25V DC. A2 VCO_VCC - Output Power Power supply for the external voltage controlled oscillator. Connect to pin 7 of the GO1555/GO1525*. This pin is an output. Should be isolated from all other power supplies. *For new designs use GO1555 A3 VCO_GND - Output Power Ground reference for the external voltage controlled oscillator. Connect to pins 2, 4, 6, and 8 of the GO1555/GO1525*. This pin is an output. Should be isolated from all other grounds. *For new designs use GO1555 A4, A5 VCO, VCO Analog Input Differential inputs for the external VCO reference signal. For single ended devices such as the GO1555/GO1525*, VCO should be AC coupled to VCO_GND. VCO is nominally 1.485GHz. *For new designs use GO1555 A6, B5, B6, C1, C4, C5, C6, C7, C8, D1, D2, D3, D4, D7, D8, E1, E2, E3, E7, F2, F3, F7, G1, G2, G3, G7, H1, H2, H3, H7, J1, J2, J3, J4 NC - - A7 PCLK - Input A8, E8, K8 IO_VDD - 30573 - 7 Power No connect. PARALLEL DATA BUS CLOCK Signal levels are LVCMOS/LVTTL compatible. HD 20-bit mode PCLK = 74.25MHz or 74.25/1.001MHz HD 10-bit mode PCLK = 148.5MHz or 148.5/1.001MHz SD 20-bit mode PCLK = 13.5MHz SD 10-bit mode PCLK = 27MHz Power supply connection for digital I/O buffers. Connect to +3.3V DC digital. February 2008 6 of 50 GS1531 Data Sheet Table 1-1: Pin Descriptions (Continued) Pin Number Name Timing Type Description A10, A9, B10, B9, C10, C9, D10, D9, E10, E9 DIN[19:10] Synchronous with PCLK Input PARALLEL DATA BUS Signal levels are LVCMOS/LVTTL compatible. DIN19 is the MSB and DIN10 is the LSB. HD 20-bit mode SD/HD = LOW 20bit/10bit = HIGH Luma data input in SMPTE mode SMPTE_BYPASS = HIGH DVB_ASI = LOW Data input in Data-Through mode SMPTE_BYPASS = LOW DVB_ASI = LOW HD 10-bit mode SD/HD = LOW 20bit/10bit = LOW Multiplexed Luma and Chroma data input in SMPTE mode SMPTE_BYPASS = HIGH DVB_ASI = LOW Data input in Data-Through mode SMPTE_BYPASS = LOW DVB_ASI = LOW SD 20-bit mode SD/HD = HIGH 20bit/10bit = HIGH Luma data input in SMPTE mode SMPTE_BYPASS = HIGH DVB_ASI = LOW Data input in Data-Through mode SMPTE_BYPASS = LOW DVB_ASI = LOW DVB-ASI data input in DVB-ASI mode SMPTE_BYPASS = LOW DVB_ASI = HIGH SD 10-bit mode SD/HD = HIGH 20bit/10bit = LOW Multiplexed Luma and Chroma data input in SMPTE mode SMPTE_BYPASS = HIGH DVB_ASI = LOW Data input in data through mode SMPTE_BYPASS = LOW DVB_ASI = LOW DVB-ASI data input in DVB-ASI mode SMPTE_BYPASS = LOW DVB_ASI = HIGH B1 CP_CAP Analog Input PLL lock time constant capacitor connection. B2 CP_VDD - Power Power supply connection for the charge pump. Connect to +3.3V DC analog. B3 CP_GND - Power Ground connection for the charge pump. Connect to analog GND. B4 LB_CONT Analog Input Control voltage to set the loop bandwidth of the integrated reclocker. B7 DETECT_TRS Non Synchronous Input CONTROL SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. Used to select the timing mode of the device. When set HIGH, the device will lock the internal flywheel to the embedded TRS timing signals in the parallel input data. When set LOW, the device will lock the internal flywheel to the externally supplied H, V, and F input signals. 30573 - 7 February 2008 7 of 50 GS1531 Data Sheet Table 1-1: Pin Descriptions (Continued) Pin Number Name Timing Type Description B8, F8, J8 IO_GND - Power Ground connection for digital I/O buffers. Connect to digital GND. C2 PD_VDD - Power Power supply connection for the phase detector. Connect to +1.8V DC analog. C3 PD_GND - Power Ground connection for the phase detector. Connect to analog GND. D5 DVB_ASI Non Synchronous Input CONTROL SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. When set HIGH in conjunction with SD/HD = HIGH and SMPTE_BYPASS = LOW, the device will be configured to operate in DVB-ASI mode. When set LOW, the device will not support the encoding of received DVB-ASI data. D6 LOCKED Synchronous with PCLK Output STATUS SIGNAL OUTPUT Signal levels are LVCMOS / LVTTL compatible. The LOCKED signal will be HIGH whenever the device has correctly received and locked to SMPTE compliant data in SMPTE mode or DVB-ASI compliant data in DVB-ASI mode, or when the device has achieved lock in Data-Through mode. It will be LOW otherwise. E4 SD/HD Non Synchronous Input CONTROL SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. When set LOW, the device will be configured to transmit signal rates of 1.485Gb/s or 1.485/1.001Gb/s only. When set HIGH, the device will be configured to transmit signal rates of 270Mb/s only. E5, F5 CORE_GND - Power Ground connection for the digital core logic. Connect to digital GND. E6, F6 CORE_VDD - Power Power supply connection for the digital core logic. Connect to +1.8V DC digital. F1 RSV - - F4 20bit/10bit Non Synchronous Input Connect to Analog GND. CONTROL SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. Used to select the input data bus width in SMPTE or Data-Through modes. When set HIGH, the parallel input will be 20-bit demultiplexed data. When set LOW, the parallel input will be 10-bit multiplexed data. 30573 - 7 February 2008 8 of 50 GS1531 Data Sheet Table 1-1: Pin Descriptions (Continued) Pin Number Name Timing Type Description F10, F9, G10, G9, H10, H9, J10, J9, K10, K9 DIN[9:0] Synchronous with PCLK Input PARALLEL DATA BUS Signal levels are LVCMOS/LVTTL compatible. DIN9 is the MSB and DIN0 is the LSB. HD 20-bit mode SD/HD = LOW 20bit/10bit = HIGH Chroma data input in SMPTE mode SMPTE_BYPASS =HIGH DVB_ASI = LOW Data input in Data-Through mode SMPTE_BYPASS = LOW DVB_ASI = LOW HD 10-bit mode SD/HD = LOW 20bit/10bit = LOW High impedance in all modes. SD 20-bit mode SD/HD = HIGH 20bit/10bit = HIGH Chroma data input in SMPTE mode SMPTE_BYPASS = HIGH DVB_ASI = LOW Data input in Data-Through mode SMPTE_BYPASS = LOW DVB_ASI = LOW High impedance in DVB-ASI mode SMPTE_BYPASS = LOW DVB_ASI = HIGH SD 10-bit mode SD/HD = HIGH 20bit/10bit = LOW G4 IOPROC_EN/DIS Non Synchronous Input High impedance in all modes. CONTROL SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. Used to enable or disable I/O processing features. When set HIGH, the following I/O processing features of the device are enabled: * EDH Packet Generation and Insertion (SD-only) * SMPTE 352M Packet Generation and Insertion * ANC Data Checksum Calculation and Insertion * Line-based CRC Generation and Insertion (HD-only) * Line Number Generation and Insertion (HD-only) * TRS Generation and Insertion * Illegal Code Remapping To enable a subset of these features, keep IOPROC_EN/DIS HIGH and disable the individual feature(s) in the IOPROC_DISABLE register accessible via the host interface. When set LOW, the I/O processing features of the device are disabled, regardless of whether the features are enabled in the IOPROC_DISABLE register. 30573 - 7 February 2008 9 of 50 GS1531 Data Sheet Table 1-1: Pin Descriptions (Continued) Pin Number Name Timing Type G5 SMPTE_BYPASS Non Synchronous Input Description CONTROL SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. When set HIGH in conjunction with DVB_ASI = LOW, the device will be configured to operate in SMPTE mode. All I/O processing features may be enabled in this mode. When set LOW, the device will not support the scrambling or encoding of received SMPTE data. No I/O processing features will be available. G6 RESET_TRST Non Synchronous Input CONTROL SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. Used to reset the internal operating conditions to default settings and to reset the JTAG test sequence. Host Mode (JTAG/HOST = LOW) When asserted LOW, all functional blocks will be set to default conditions and all input and output signals become high impedance, including the serial digital outputs SDO and SDO. Must be set HIGH for normal device operation. JTAG Test Mode (JTAG/HOST = HIGH) When asserted LOW, all functional blocks will be set to default and the JTAG test sequence will be held in reset. When set HIGH, normal operation of the JTAG test sequence resumes. G8 BLANK Synchronous with PCLK Input CONTROL SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. Used to enable or disable input data blanking. When set LOW, the luma and chroma input data is set to the appropriate blanking levels. Horizontal and vertical ancillary spaces will also be set to blanking levels. When set HIGH, the luma and chroma input data pass through the device unaltered. H4 CS_TMS Synchronous with SCLK_TCK Input CONTROL SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. Chip Select / Test Mode Select Host Mode (JTAG/HOST = LOW) CS_TMS operates as the host interface chip select, CS, and is active LOW. JTAG Test Mode (JTAG/HOST = HIGH) CS_TMS operates as the JTAG test mode select, TMS, and is active HIGH. NOTE: If the host interface is not being used, tie this pin HIGH. H5 SCLK_TCK Non Synchronous Input CONTROL SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. Serial Data Clock / Test Clock. Host Mode (JTAG/HOST = LOW) SCLK_TCK operates as the host interface burst clock, SCLK. Command and data read/write words are clocked into the device synchronously with this clock. JTAG Test Mode (JTAG/HOST = HIGH) SCLK_TCK operates as the JTAG test clock, TCK. NOTE: If the host interface is not being used, tie this pin HIGH. 30573 - 7 February 2008 10 of 50 GS1531 Data Sheet Table 1-1: Pin Descriptions (Continued) Pin Number Name Timing Type Description H6 SDOUT_TDO Synchronous with SCLK_TCK Output CONTROL SIGNAL OUTPUT Signal levels are LVCMOS/LVTTL compatible. Serial Data Output / Test Data Output Host Mode (JTAG/HOST = LOW) SDOUT_TDO operates as the host interface serial output, SDOUT, used to read status and configuration information from the internal registers of the device. JTAG Test Mode (JTAG/HOST = HIGH) SDOUT_TDO operates as the JTAG test data output, TDO. H8 H Synchronous with PCLK Input CONTROL SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. Used to indicate the portion of the video line containing active video data when DETECT_TRS is set LOW. The device will set the H bit in all outgoing TRS signals for the entire period that the H input signal is HIGH (IOPROC_EN/DIS must also be HIGH). H signal timing is configurable via the H_CONFIG bit of the IOPROC_DISABLE register, accessible via the host interface. Active Line Blanking (H_CONFIG = 0h) The H signal should be set HIGH for the entire horizontal blanking period, including the EAV and SAV TRS words, and LOW otherwise. This is the default setting. TRS Based Blanking (H_CONFIG = 1h) The H signal should be set HIGH for the entire horizontal blanking period as indicated by the H bit in the received TRS ID words, and LOW otherwise. J5 SDO_EN/DIS Non Synchronous Input CONTROL SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. Used to enable or disable the serial digital output stage. When set LOW, the serial digital output signals SDO and SDO are disabled and become high impedance. When set HIGH, the serial digital output signals SDO and SDO are enabled. J6 SDIN_TDI Synchronous with SCLK_TCK Input CONTROL SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. Serial Data In / Test Data Input Host Mode (JTAG/HOST = LOW) SDIN_TDI operates as the host interface serial input, SDIN, used to write address and configuration information to the internal registers of the device. JTAG Test Mode (JTAG/HOST = HIGH) SDIN_TDI operates as the JTAG test data input, TDI. NOTE: If the host interface is not being used, tie this pin HIGH. 30573 - 7 February 2008 11 of 50 GS1531 Data Sheet Table 1-1: Pin Descriptions (Continued) Pin Number Name Timing Type Description J7 V Synchronous with PCLK Input CONTROL SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. Used to indicate the portion of the video field / frame that is used for vertical blanking when DETECT_TRS is set LOW. The device will set the V bit in all outgoing TRS signals for the entire period that the V input signal is HIGH (IOPROC_EN/DIS must also be HIGH). The V signal should be set HIGH for the entire vertical blanking period and should be set LOW for all lines outside of the vertical blanking interval. The V signal is ignored when DETECT_TRS = HIGH. K1 RSET Analog Input Used to set the serial digital output signal amplitude. Connect to CD_VDD through 281 +/- 1% for 800mVp-p single-ended output swing. K2 CD_VDD - Power Power supply connection for the serial digital cable driver. Connect to +1.8V DC analog. K3, K4 SDO, SDO Analog Output Serial digital output signal operating at 1.485Gb/s, 1.485/1.001Gb/s, or 270Mb/s. The slew rate of these outputs is automatically controlled to meet SMPTE 292M and 259M requirements according to the setting of the SD/HD pin. K5 CD_GND - Power Ground connection for the serial digital cable driver. Connect to analog GND. K6 JTAG/HOST Non Synchronous Input CONTROL SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. Used to select JTAG Test Mode or Host Interface Mode. When set HIGH, CS_TMS, SDOUT_TDO, SDI_TDI and SCLK_TCK are configured for JTAG boundary scan testing. When set LOW, CS_TMS, SDOUT_TDO, SDI_TDI and SCLK_TCK are configured as GSPI pins for normal host interface operation. K7 F Synchronous with PCLK Input CONTROL SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. Used to indicate the ODD / EVEN field of the video signal when DETECT_TRS is set LOW. The device will set the F bit in all outgoing TRS signals for the entire period that the F input signal is HIGH (IOPROC_EN/DIS must also be HIGH). The F signal should be set HIGH for the entire period of field 2 and should be set LOW for all lines in field 1 and for all lines in progressive scan systems. The F signal is ignored when DETECT_TRS = HIGH. 30573 - 7 February 2008 12 of 50 GS1531 Data Sheet 2. Electrical Characteristics 2.1 Absolute Maximum Ratings Parameter Value/Units Supply Voltage Core -0.3V to +2.1V Supply Voltage I/O -0.3V to +4.6V Input Voltage Range (any input) -2.0V to + 5.25V Ambient Operating Temperature -20C < TA < 85C Storage Temperature -40C < TSTG < 125C ESD Protection On All Pins (see Note 1) 1kV NOTES: 1. HBM, per JESDA-114B. 2.2 DC Electrical Characteristics Table 2-1: DC Electrical Characteristics TA = 0C to 70C, unless otherwise specified. Parameter Symbol Conditions Min Typ Max Units Test Level Notes Operation Temperature Range TA - 0 - 70 C 3 1 Digital Core Supply Voltage CORE_VDD - 1.71 1.8 1.89 V 3 1 Digital I/O Supply Voltage IO_VDD - 3.13 3.3 3.47 V 3 1 Charge Pump Supply Voltage CP_VDD - 3.13 3.3 3.47 V 3 1 Phase Detector Supply Voltage PD_VDD - 1.71 1.8 1.89 V 3 1 Input Buffer Supply Voltage BUFF_VDD - 1.71 1.8 1.89 V 3 1 Cable Driver Supply Voltage CD_VDD - 1.71 1.8 1.89 V 3 1 External VCO Supply Voltage Output VCO_VCC - 2.25 - 2.75 V 1 - +1.8V Supply Current I1V8 SDO Enabled - - 245 mA 3 3 +3.3V Supply Current I3V3 - - - 45 mA 3 4 Total Device Power PD SDO Enabled - - 590 mW 3 - System 30573 - 7 February 2008 13 of 50 GS1531 Data Sheet Table 2-1: DC Electrical Characteristics (Continued) TA = 0C to 70C, unless otherwise specified. Parameter Symbol Conditions Min Typ Max Units Test Level Notes Input Logic LOW VIL - - - 0.8 V 4 - Input Logic HIGH VIH - 2.1 - - V 4 - Output Logic LOW VOL +8mA - 0.2 0.4 V 4 - Output Logic HIGH VOH -8mA IO_VDD - 0.4 - - V 4 - VRSET RSET=281 0.54 0.6 0.66 V 1 2 VCMOUT 75 load, RSET=281, SD and HD 0.8 1.0 1.2 V 1 - Digital I/O Input RSET Voltage Output Output Common Mode Voltage TEST LEVELS NOTES 1. Production test at room temperature and nominal supply voltage with guardbands for supply and temperature ranges. 2. Production test at room temperature and nominal supply voltage with guardbands for supply and temperature ranges using correlated test. 3. Production test at room temperature and nominal supply voltage. 4. QA sample test. 5. Calculated result based on Level 1, 2, or 3. 6. Not tested. Guaranteed by design simulations. 7. Not tested. Based on characterization of nominal parts. 8. Not tested. Based on existing design/characterization data of similar product. 9. Indirect test. 1. 2. 3. 4. All DC and AC electrical parameters within specification. Set by the value of the RSET resistor. Sum of all 1.8V supplies. Sum of all 3.3V supplies. 2.3 AC Electrical Characteristics Table 2-2: AC Electrical Characteristics TA = 0C to 70C, unless otherwise shown Parameter Symbol Conditions Min Typ Max Units Test Level Notes - 10-bit SD - 21 - PCLK 8 - - - 20-bit HD - 19 - PCLK 8 - DVB-ASI - 11 - PCLK 8 - treset - 1 - - ms 8 1 System Device Latency Reset Pulse Width 30573 - 7 February 2008 14 of 50 GS1531 Data Sheet Table 2-2: AC Electrical Characteristics (Continued) TA = 0C to 70C, unless otherwise shown Parameter Symbol Conditions Min Typ Max Units Test Level Notes Parallel Clock Frequency fPCLK - 13.5 - 148.5 MHz 4 - Parallel Clock Duty Cycle DCPCLK - 40 - 60 % 6 - Input Data Setup Time tsu - 2.0 - - ns 5 - Input Data Hold Time tih - 1.5 - - ns 5 - DRSDO - - 1.485 - Gb/s 1 - - - 1.485/1.001 - Gb/s 9 - Parallel Input Serial Digital Output Serial Output Data Rate - - 270 - Mb/s 1 - 650 800 950 mVp-p 1 - HD signal - - 260 ps 1 - trSDO SD signal 400 550 1500 ps 1 - Serial Output Fall Time 20% ~ 80% tfSDO HD signal - - 260 ps 1 - tfSDO SD signal 400 550 1500 ps 1 - Serial Output Intrinsic Jitter tIJ Pseudorandom and pathological HD signal - 90 125 ps 5 - tIJ Pseudorandom and pathological SD signal - 270 350 ps 5 - - 6.6 MHz 8 - Serial Output Swing VSDD RSET = 281 75 load Serial Output Rise Time 20% ~ 80% trSDO GSPI GSPI Input Clock Frequency fSCLK - - GSPI Input Clock Duty Cycle DCSCLK - 40 - 60 % 8 - GSPI Input Data Setup Time - - 0 - - ns 8 - GSPI Input Data Hold Time - - 1.43 - - ns 8 - GSPI Output Data Hold Time - - 2.1 - - ns 8 - GSPI Output Data Delay Time - - - - 7.27 ns 8 - TEST LEVELS NOTES 1. Production test at room temperature and nominal supply voltage with guardbands for supply and temperature ranges. 2. Production test at room temperature and nominal supply voltage with guardbands for supply and temperature ranges using correlated test. 3. Production test at room temperature and nominal supply voltage. 4. QA sample test. 5. Calculated result based on Level 1, 2, or 3. 6. Not tested. Guaranteed by design simulations. 7. Not tested. Based on characterization of nominal parts. 8. Not tested. Based on existing design/characterization data of similar product. 9. Indirect test. 1. See Device Power Up on page 45, Figure 4-12. 30573 - 7 February 2008 15 of 50 GS1531 Data Sheet 2.4 Solder Reflow Profiles The GS1531 is available in a Pb or Pb-free package. It is recommended that the Pb package be soldered with Pb paste using the Standard Eutectic profile shown in Figure 2-1, and the Pb-free package be soldered with Pb-free paste using the reflow profile shown in Figure 2-2. NOTE: It is possible to solder a Pb-free package with Pb paste using a Standard Eutectic profile with a reflow temperature maintained at 245oC - 250oC. 60-150 sec. Temperature 10-20 sec. 230C 220C 3C/sec max 183C 6C/sec max 150C 100C 25C Time 120 sec. max 6 min. max Figure 2-1: Standard Eutectic Solder Reflow Profile (Pb package, Pb paste) Temperature 60-150 sec. 20-40 sec. 260C 250C 3C/sec max 217C 6C/sec max 200C 150C 25C Time 60-180 sec. max 8 min. max Figure 2-2: Maximum Pb-free Solder Reflow Profile (Pb-free package, Pb-free paste) 30573 - 7 February 2008 16 of 50 GS1531 Data Sheet 3. Input/Output Circuits All resistors in ohms, all capacitors in farads, unless otherwise shown. SDO SDO Figure 3-1: Serial Digital Output LF CP_CAP 300 Figure 3-2: VCO Control Output & PLL Lock Time Capacitor VDD 42K 63K PCLK Figure 3-3: PCLK Input 30573 - 7 February 2008 17 of 50 GS1531 Data Sheet VCO VDD 25 1.5K 5K 25 VCO Figure 3-4: VCO Input LB_CONT 865mV 7.2K Figure 3-5: PLL Loop Bandwidth Control 30573 - 7 February 2008 18 of 50 IOPROC_DISABLE EDH_FLAG VIDEO_STANDARD VIDEO_FORMAT_B VIDEO_FORMAT_A FF_LINE_END_F1 FF_LINE_START_F1 FF_LINE_END_F0 FF_LINE_START_F0 AP_LINE_END_F1 AP_LINE_START_F1 AP_LINE_END_F0 AP_LINE_START_F0 RASTER_STRUCTURE4 RASTER_STRUCTURE3 RASTER_STRUCTURE2 RASTER_STRUCTURE1 REGISTER NAME LINE_352M_f2 LINE_352M_f1 03h 02h 01h 00h ADDRESS 1Ch 1Bh 1Ah 19h 18h 17h 16h 15h 14h 13h 12h 11h 10h 0Fh 0Eh 0Dh 0Ch 0Bh 0Ah 09h 08h 07h 06h 05h 04h Not Used Not Used Not Used VF4-b7 VF2-b7 Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used 15 Not Used Not Used Not Used ANC-IDA VDS-b3 VF4-b5 VF2-b5 Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used 13 Not Used Not Used 30573 - 7 Not Used ANC-UES VDS-b4 VF4-b6 VF2-b6 Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used 14 Not Used Not Used 3.1 Host Interface Maps Not Used ANC-EDA VDS-b1 VF4-b3 VF2-b3 Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used b11 b11 11 Not Used Not Used February 2008 Not Used ANC-IDH VDS-b2 VF4-b4 VF2-b4 Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used 12 Not Used Not Used Not Used ANC-EDH VDS-b0 VF4-b2 VF2-b2 Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used b10 b10 b10 b10 10 b10 b10 Not Used FF-UES INT_PROG VF4-b1 VF2-b1 b9 b9 b9 b9 b9 b9 b9 b9 b9 b9 b9 b9 9 b9 b9 H_CONFIG FF-IDA STD_ LOCK VF4-b0 VF2-b0 b8 b8 b8 b8 b8 b8 b8 b8 b8 b8 b8 b8 8 b8 b8 Not Used FF-IDH NOT USED VF3-b7 VF1-b7 b7 b7 b7 b7 b7 b7 b7 b7 b7 b7 b7 b7 7 b7 b7 352M_INS FF-EDA NOT USED VF3-b6 VF1-b6 b6 b6 b6 b6 b6 b6 b6 b6 b6 b6 b6 b6 6 b6 b6 ILLEGAL_RE MAP FF-EDH NOT USED VF3-b5 VF1-b5 b5 b5 b5 b5 b5 b5 b5 b5 b5 b5 b5 b5 5 b5 b5 4 EDH_CRC_IN S AP-UES NOT USED VF3-b4 VF1-b4 b4 b4 b4 b4 b4 b4 b4 b4 b4 b4 b4 b4 b4 b4 3 ANC_ CSUM_INS AP-IDA NOT USED VF3-b3 VF1-b3 b3 b3 b3 b3 b3 b3 b3 b3 b3 b3 b3 b3 b3 b3 CRC_INS AP-IDH NOT USED VF3-b2 VF1-b2 b2 b2 b2 b2 b2 b2 b2 b2 b2 b2 b2 b2 2 b2 b2 TRS_INS AP-EDH NOT USED VF3-b0 VF1-b0 b0 b0 b0 b0 b0 b0 b0 b0 b0 b0 b0 b0 0 b0 b0 19 of 50 LNUM_ INS AP-EDA NOT USED VF3-b1 VF1-b1 b1 b1 b1 b1 b1 b1 b1 b1 b1 b1 b1 b1 1 b1 b1 GS1531 Data Sheet VIDEO_STANDARD RASTER_STRUCTURE4 RASTER_STRUCTURE3 RASTER_STRUCTURE2 RASTER_STRUCTURE1 REGISTER NAME 03h 02h 01h 00h ADDRESS 1Ch 1Bh 1Ah 19h 18h 17h 16h 15h 14h 13h 12h 11h 10h 0Fh 0Eh 0Dh 0Ch 0Bh 0Ah 09h 08h 07h 06h 05h 04h 15 VDS-b3 13 30573 - 7 VDS-b4 14 VDS-b1 b11 b11 11 February 2008 VDS-b2 12 VDS-b0 b10 b10 b10 b10 10 3.1.1 Host Interface Map (Read Only Registers) INT_PROG b9 b9 b9 b9 9 STD_ LOCK b8 b8 b8 b8 8 b7 b7 b7 b7 7 b6 b6 b6 b6 6 b5 b5 b5 b5 5 b4 b4 b4 b4 4 b3 b3 b3 b3 3 b2 b2 b2 b2 2 b1 b1 b1 b1 1 20 of 50 b0 b0 b0 b0 0 GS1531 Data Sheet IOPROC_DISABLE EDH_FLAG VIDEO_FORMAT_B VIDEO_FORMAT_A FF_LINE_END_F1 FF_LINE_START_F1 FF_LINE_END_F0 FF_LINE_START_F0 AP_LINE_END_F1 AP_LINE_START_F1 AP_LINE_END_F0 AP_LINE_START_F0 REGISTER NAME LINE_352M_f2 LINE_352M_f1 ADDRESS 1Ch 1Bh 1Ah 19h 18h 17h 16h 15h 14h 13h 12h 11h 10h 0Fh 0Eh 0Dh 0Ch 0Bh 0Ah 09h 08h 07h 06h 05h 04h 03h 02h 01h 00h VF4-b7 VF2-b7 15 ANC-IDA VF4-b5 VF2-b5 13 30573 - 7 ANC-UES VF4-b6 VF2-b6 14 ANC-EDA VF4-b3 VF2-b3 11 February 2008 ANC-IDH VF4-b4 VF2-b4 12 ANC-EDH VF4-b2 VF2-b2 10 b10 b10 FF-UES VF4-b1 VF2-b1 b9 b9 b9 b9 b9 b9 b9 b9 9 b9 b9 3.1.2 Host Interface Map (R/W Configurable Registers) H_CONFIG FF-IDA VF4-b0 VF2-b0 b8 b8 b8 b8 b8 b8 b8 b8 8 b8 b8 FF-IDH VF3-b7 VF1-b7 b7 b7 b7 b7 b7 b7 b7 b7 7 b7 b7 352M_INS FF-EDA VF3-b6 VF1-b6 b6 b6 b6 b6 b6 b6 b6 b6 6 b6 b6 ILLEGAL_RE MAP FF-EDH VF3-b5 VF1-b5 b5 b5 b5 b5 b5 b5 b5 b5 5 b5 b5 EDH_CRC_IN S AP-UES VF3-b4 VF1-b4 b4 b4 b4 b4 b4 b4 b4 b4 4 b4 b4 ANC_ CSUM_INS AP-IDA VF3-b3 VF1-b3 b3 b3 b3 b3 b3 b3 b3 b3 3 b3 b3 CRC_INS AP-IDH VF3-b2 VF1-b2 b2 b2 b2 b2 b2 b2 b2 b2 2 b2 b2 TRS_INS AP-EDH VF3-b0 VF1-b0 b0 b0 b0 b0 b0 b0 b0 b0 0 b0 b0 21 of 50 LNUM_ INS AP-EDA VF3-b1 VF1-b1 b1 b1 b1 b1 b1 b1 b1 b1 1 b1 b1 GS1531 Data Sheet GS1531 Data Sheet 4. Detailed Description 4.1 Functional Overview The GS1531 is a multi-rate serializer with an integrated cable driver. When used in conjunction with the external GO1555/GO1525* Voltage Controlled Oscillator, a transmit solution at 1.485Gb/s, 1.485/1.001Gb/s or 270Mb/s is realized. The device has three different modes of operation which must be set through external device pins. When SMPTE mode is enabled, the device will accept 10-bit multiplexed or 20-bit demultiplexed SMPTE compliant data at both HD and SD signal rates. The device's additional processing features are also enabled in this mode. In DVB-ASI mode, the GS1531 will accept an 8-bit parallel DVB-ASI compliant transport stream on its upper input bus. The serial output data stream will be 8b/10b encoded and stuffed. The GS1531's third mode allows for the serializing of data not conforming to SMPTE or DVB-ASI streams. The provided serial digital outputs feature a high impedance mode, output mute on loss of parallel clock and adjustable signal swing. The output slew rate is automatically controlled by the SD/HD setting. In the digital signal processing core, several data processing functions are implemented including SMPTE 352M and EDH data packet generation and insertion, and automatic video standards detection. These features are all enabled by default, but may be individually disabled via internal registers accessible through the GSPI host interface. Finally, the GS1531 contains a JTAG interface for boundary scan test implementations. *For new designs use GO1555 4.2 Parallel Data Inputs Data inputs enter the device on the rising edge of PCLK as shown in Figure 4-1. The input data format is defined by the setting of the external SD/HD, SMPTE_BYPASS and DVB_ASI pins and may be presented in 10-bit or 20-bit format. The input data bus width is controlled independently from the internal data bus width by the 20bit/10bit input pin. 30573 - 7 February 2008 22 of 50 GS1531 Data Sheet PCLK DIN[19:0] DATA Control signal input tSU tIH Figure 4-1: PCLK to Data Timing 4.2.1 Parallel Input in SMPTE Mode When the device is operating in SMPTE mode, see SMPTE Mode on page 25, both SD and HD data may be presented to the input bus in either multiplexed or demultiplexed form depending on the setting of the 20bit/10bit input pin. In 20-bit mode, (20bit/10bit = HIGH), the input data format should be word aligned, demultiplexed luma and chroma data. Luma words should be presented to DIN[19:10] while chroma words should occupy DIN[9:0]. In 10-bit mode, (20bit/10bit = LOW), the input data format should be word aligned, multiplexed luma and chroma data. The data should be presented to DIN[19:10]. DIN[9:0] will be high impedance in this mode. 4.2.2 Parallel Input in DVB-ASI Mode When operating in DVB-ASI mode, see DVB-ASI mode on page 26, the GS1531 requires the input data bus to be configured for 10-bit operation (20bit/10bit = LOW). The device accepts 8-bit data words on DIN[17:10] such that DIN17 = HIN is the most significant bit of the encoded transport stream data and DIN10 = AIN is the least significant bit. In addition, DIN19 and DIN18 are configured as the DVB-ASI control signals INSSYNCIN and KIN respectively. See DVB-ASI mode on page 26 for a description of these DVB-ASI specific input signals. The pins DIN[9:0] are high impedance when the GS1531 is operating in DVB-ASI mode. 4.2.3 Parallel Input in Data-Through Mode When operating in Data-Through mode, see Data-Through Mode on page 28, the GS1531 passes data presented to the parallel input bus to the serial output without performing any encoding or scrambling. The input data bus width accepted by the device in this mode is controlled by the setting of the 20bit/10bit pin. 30573 - 7 February 2008 23 of 50 GS1531 Data Sheet 4.2.4 Parallel Input Clock (PCLK) The frequency of the PCLK input signal required by the GS1531 is determined by the input data format. Table 4-1 below lists the possible input signal formats and their corresponding parallel clock rates. NOTE: DVB-ASI input requires a 10-bit wide input data bus (20bit/10bit = LOW). Table 4-1: Parallel Data Input Format Control Signals Input Data Format DIN [19:10] DIN [9:0] PCLK 20bit/ 10bit SD/ HD SMPTE_BYPASS DVB_ASI 20bit DEMULTIPLEXED SD LUMA CHROMA 13.5MHz HIGH HIGH HIGH LOW 10bit MULTIPLEXED SD LUMA / CHROMA HIGH IMPEDANCE 27MHz LOW HIGH HIGH LOW 20bit DEMULTIPLEXED HD LUMA CHROMA 74.25 or HIGH LOW HIGH LOW LOW LOW HIGH LOW LOW HIGH LOW HIGH LOW HIGH LOW HIGH SMPTE MODE 74.25/ 1.001MHz 10bit MULTIPLEXED HD LUMA / CHROMA HIGH IMPEDANCE 148.5 or DVB-ASI HIGH IMPEDANCE 27MHz DATA 20bit DEMULTIPLEXED SD DATA DATA 13.5MHz HIGH HIGH LOW LOW 10bit MULTIPLEXED SD DATA HIGH IMPEDANCE 27MHz LOW HIGH LOW LOW 20bit DEMULTIPLEXED HD DATA DATA 74.25 or HIGH LOW LOW LOW LOW LOW LOW LOW 148.5/ 1.001MHz DVB-ASI MODE 10bit DVB-ASI DATA-THROUGH MODE 74.25/ 1.001MHz 10bit MULTIPLEXED HD DATA HIGH IMPEDANCE 30573 - 7 148.5 or 148.5/ 1.001MHz February 2008 24 of 50 GS1531 Data Sheet 4.3 SMPTE Mode The GS1531 is said to be in SMPTE mode when the SMPTE_BYPASS pin is set HIGH and the DVB_ASI pin is set LOW. In this mode, the parallel data will be scrambled according to SMPTE 259M or 292M, and NRZ-to-NRZI encoded prior to serialization. 4.3.1 Internal Flywheel The GS1531 has an internal flywheel which is used in the generation of internal / external timing signals, and in automatic video standards detection. It is operational in SMPTE mode only. The flywheel consists of a number of counters and comparators operating at video pixel and video line rates. These counters maintain information about the total line length, active line length, total number of lines per field / frame and total active lines per field / frame for the received video standard. When DETECT_TRS is LOW, the flywheel will be locked to the externally supplied H, V, and F timing signals. When DETECT_TRS is HIGH, the flywheel will be locked to the embedded TRS signals in the parallel input data. Both 8-bit and 10-bit TRS code words will be identified by the device. The flywheel 'learns' the video standard by timing the horizontal and vertical reference information supplied a the H, V, and F input pins, or contained in the TRS ID words of the received video data. Full synchronization of the flywheel to the received video standard therefore requires one complete video frame. Once synchronization has been achieved, the flywheel will continue to monitor the received TRS timing or the supplied H, V, and F timing information to maintain synchronization. 4.3.2 HVF Timing Signal Extraction As discussed above, the GS1531's internal flywheel may be locked to externally provided H, V, and F signals when DETECT_TRS is set LOW. The H signal timing should also be configured via the H_CONFIG bit of the internal IOPROC_DISABLE register as either active line based blanking or TRS based blanking, see Packet Generation and Insertion on page 30. Active line based blanking is enabled when the H_CONFIG bit is set LOW. In this mode, the H input should be HIGH for the entire horizontal blanking period, including the EAV and SAV TRS words. This is the default H timing assumed by the device. When H_CONFIG is set HIGH, TRS based blanking is enabled. In this case, the H input should be set HIGH for the entire horizontal blanking period as indicated by the H bit in the associated TRS words. The timing of these signals is shown in Figure 4-2. 30573 - 7 February 2008 25 of 50 GS1531 Data Sheet PCLK LUMA DATA OUT 3FF 000 000 XYZ (eav) 3FF 000 000 XYZ (sav) CHROMA DATA OUT 3FF 000 000 XYZ (eav) 3FF 000 000 XYZ (sav) H V F H:V:F TIMING - HD 20-BIT INPUT MODE PCLK MULTIPLEXED Y/Cr/Cb DATA OUT 3FF 3FF 000 000 000 XYZ (eav) XYZ (eav) 000 XYZ (sav) XYZ (sav) 000 H V F H:V:F TIMING AT EAV - HD 10-BIT INPUT MODE PCLK MULTIPLEXED Y/Cr/Cb DATA OUT 3FF 3FF 000 000 000 H V F H;V:F TIMING AT SAV - HD 10-BIT INPUT MODE PCLK CHROMA DATA OUT 3FF 000 3FF 000 LUMA DATA OUT 000 XYZ (eav) 000 XYZ (SAV) H V H SIGNAL TIMING: H_CONFIG = LOW F H_CONFIG = HIGH H:V:F TIMING - SD 20-BIT INPUT MODE PCLK MULTIPLEXED Y/Cr/Cb DATA OUT 3FF 000 000 XYZ (eav) 3FF 000 000 XYZ (sav) H V F H:V:F TIMING - SD 10-BIT INPUT MODE Figure 4-2: H, V, F Timing 4.4 DVB-ASI mode To operate the GS1531 in DVB-ASI mode, set the SMPTE_BYPASS and 20bit/10bit pins LOW, and the DVB_ASI and SD/HD pins HIGH. 30573 - 7 February 2008 26 of 50 GS1531 Data Sheet 4.4.1 Control Signal Inputs In DVB-ASI mode, the DIN19 and DIN18 pins will be configured as DVB-ASI control signals INSSYNCIN and KIN respectively. When INSSYNCIN is set HIGH, the device will insert K28.5 sync characters into the data stream. This function is used to assist system implementations where the GS1531 may be preceded by an external data FIFO. Parallel DVB-ASI data may be clocked into the FIFO at some rate less than 27MHz. The INSSYNCIN input may then be connected to the FIFO empty signal, thus providing a means of padding up the data transmission rate to 27MHz. See Figure 4-3. NOTE: 8b/10b encoding will take place after K28.5 sync character insertion. KIN should be set HIGH whenever the parallel data input is to be interpreted as any special character defined by the DVB-ASI standard (including the K28.5 sync character). This pin should be set LOW when the input is to be interpreted as data. NOTE: When operating in DVB-ASI mode, DIN[9:0] become high impedance. AIN ~ HIN SDO TS 8 8 FIFO GS1531 KIN KIN WRITE_CLK <27MHz READ CLK =27MHz SDO CLK_IN FE INSSYNCIN CLK_OUT PCLK = 27MHz Figure 4-3: DVB-ASI FIFO Implementation using the GS1531 30573 - 7 February 2008 27 of 50 GS1531 Data Sheet 4.5 Data-Through Mode The GS1531 may be configured to operate as a simple parallel-to-serial converter. In this mode, the device presents data to the output buffer without performing any scrambling or encoding. Data-through mode is enabled only when both the SMPTE_BYPASS and DVB_ASI pins are set LOW. 4.6 Additional Processing Functions The GS1531 contains an additional data processing block which is available in SMPTE mode only, see SMPTE Mode on page 25. 4.6.1 Input Data Blank The video input data may be 'blanked' by the GS1531. In this mode, all input video data except TRS words are set to the appropriate blanking levels by the device. Both the horizontal and vertical ancillary data spaces will also be set to blanking levels. This function is enabled by setting the BLANK pin LOW. 4.6.2 Automatic Video Standard Detection The GS1531 can detect the input video standard by using the timing parameters extracted from the received TRS ID words or supplied H, V, and F timing signals, see Internal Flywheel on page 25. This information is presented to the host interface via the VIDEO_STANDARD register (Table 4-2). Total samples per line, active samples per line, total lines per field/frame and active lines per field/frame are also calculated and presented to the host interface via the RASTER_STRUCTURE registers (Table 4-3). These line and sample count registers are updated once per frame at the end of line 12. This is in addition to the information contained in the VIDEO_STANDARD register. After device reset, the four RASTER_STRUCTURE registers default to zero. Table 4-2: Host Interface Description for Video Standard Register Register Name Bit Name Description R/W Default VIDEO_STANDARD Address: 004h 15 - Not Used. - - 14-10 VD_STD[4:0] Video Data Standard (see Table 4-4). R 0 9 INT_PROG Interlace/Progressive: Set LOW if detected video standard is PROGRESSIVE and is set HIGH if it is INTERLACED. R 0 8 STD_LOCK Standard Lock: Set HIGH when flywheel has achieved full synchronization. R 0 7-0 - Not Used. - - 30573 - 7 February 2008 28 of 50 GS1531 Data Sheet Table 4-3: Host Interface Description for Raster Structure Registers Register Name Bit Name Description R/W Default RASTER_STRUCTURE1 Address: 00Eh 15-12 - Not Used. - - 11-0 RASTER_STRUCTURE_1[11:0] Words Per Active Line R 0 RASTER_STRUCTURE2 Address: 00Fh 15-13 - Not Used. - - 12-0 RASTER_STRUCTURE_2[12:0] Words Per Total Line. R 0 RASTER_STRUCTURE3 Address: 010h 15-11 - Not Used. - - 10-0 RASTER_STRUCTURE_3[10:0] Total Lines Per Frame R 0 RASTER_STRUCTURE4 Address: 011h 15-11 - Not Used. - - 10-0 RASTER_STRUCTURE_4[10:0] Active Lines Per Field R 0 4.6.2.1 Video Standard Indication The video standard codes reported in the VD_STD[4:0] bits of the VIDEO_STANDARD register represent the SMPTE standards as shown in Table 4-4. In addition to the 5-bit video standard code word, the VIDEO_STANDARD register also contains two status bits. The STD_LOCK bit will be set HIGH whenever the flywheel has achieved full synchronization. The INT_PROG bit will be set LOW if the detected video standard is progressive and HIGH if the detected video standard is interlaced. The VD_STD[4:0], STD_LOCK and INT_PROG bits of the VIDEO_STANDARD register will default to zero after device reset. The VD_STD[4:0] and INT_PROG bits will also default to zero if the SMPTE_BYPASS pin is asserted LOW or if the LOCKED output is LOW. The STD_LOCK bit will retain its previous value if the PCLK is removed. Table 4-4: Supported Video Standards VD_STD[4:0] SMPTE Standard Video Format Length of HANC Length of Active Video Total Samples SMPTE352M Lines 00h 296M (HD) 1280x720/60 (1:1) 358 1280 1650 10 01h 296M (HD) 1280x720/60 (1:1) - EM 198 1440 1650 10 02h 296M (HD) 1280x720/30 (1:1) 2008 1280 3300 10 03h 296M (HD) 1280x720/30 (1:1) - EM 408 2880 3300 10 04h 296M (HD) 1280x720/50 (1:1) 688 1280 1980 10 05h 296M (HD) 1280x720/50 (1:1) - EM 240 1728 1980 10 06h 296M (HD) 1280x720/25 (1:1) 2668 1280 3960 10 07h 296M (HD) 1280x720/25 (1:1) - EM 492 3456 3960 10 30573 - 7 February 2008 29 of 50 GS1531 Data Sheet Table 4-4: Supported Video Standards (Continued) VD_STD[4:0] SMPTE Standard Video Format Length of HANC Length of Active Video Total Samples SMPTE352M Lines 08h 296M (HD) 1280x720/24 (1:1) 2833 1280 4125 10 09h 296M (HD) 1280x720/24 (1:1) - EM 513 3600 4125 10 0Ah 274M (HD) 1920x1080/60 (2:1) or 1920x1080/30 (PsF) 268 1920 2200 10, 572 0Bh 274M (HD) 1920x1080/30 (1:1) 268 1920 2200 18 0Ch 274M (HD) 1920x1080/50 (2:1) or 708 1920 2640 10, 572 1920x1080/25 (PsF) 0Dh 274M (HD) 1920x1080/25 (1:1) 708 1920 2640 18 0Eh 274M (HD) 1920x1080/25 (1:1) - EM 324 2304 2640 18 0Fh 274M (HD) 1920x1080/25 (PsF) - EM 324 2304 2640 10, 572 10h 274M (HD) 1920x1080/24 (1:1) 818 1920 2750 18 11h 274M (HD) 1920x1080/24 (PsF) 818 1920 2750 10, 572 12h 274M (HD) 1920x1080/24 (1:1) - EM 338 2400 2750 18 13h 274M (HD) 1920x1080/24 (PsF) - EM 338 2400 2750 10, 572 14h 295M (HD) 1920x1080/50 (2:1) 444 1920 2376 10, 572 15h 260M (HD) 1920x1035/60 (2:1) 268 1920 2200 10, 572 16h 125M (SD) 1440x487/60 (2:1) 268 1440 1716 10, 276 268 1440 1716 10, 276 (Or dual link progressive) 17h 125M (SD) 1440x507/60 (2:1) 19h 125M (SD) 525-line 487 generic - - 1716 10, 276 1Bh 125M (SD) 525-line 507 generic - - 1716 10, 276 18h ITU-R BT.656 1440x576/50 (2:1) 280 1440 1728 9, 322 (SD) (Or dual link progressive) ITU-R BT.656 625-line generic (EM) - - 1728 9, 322 1Ah (SD) 1Dh Unknown HD - - - - - 1Eh Unknown SD - - - - - 1Ch, 1Fh Reserved - - - - - NOTE: Though the GS1531 will work correctly on and serialize both 59.94Hz and 60Hz formats, it will not distinguish between them. 4.6.3 Packet Generation and Insertion In addition to input data blanking and automatic video standards detection, the GS1531 may also calculate, assemble and insert into the data stream various types of ancillary data packets and TRS ID words. 30573 - 7 February 2008 30 of 50 GS1531 Data Sheet These features are only available when the device is set to operated in SMPTE mode and the IOPROC_EN/DIS pin is set HIGH. Individual insertion features may be enabled or disabled via the IOPROC_DISABLE register (Table 4-5). All of the IOPROC_DISABLE register bits default to '0' after device reset, enabling all of the processing features. To disable any individual error correction feature, the host interface must set the corresponding bit HIGH in this register. Table 4-5: Host Interface Description for Internal Processing Disable Register Register Name Bit Name Description R/W Default IOPROC_DISABLE Address: 000h 15-9 - Not Used. - - 8 H_CONFIG Horizontal sync timing input configuration. Set LOW when the H input timing is based on active line blanking (default). Set HIGH when the H input timing is based on the H bit of the TRS words. See Figure 4-2. R/W 0 7 - Not Used. - - 6 352M_INS SMPTE352M packet insertion. In HD mode, 352M packets are inserted in the Y channel only when one of the bytes in the VIDEO_FORMAT_A or VIDEO_FORMAT_B registers are programmed with non-zero values. The IOPROC_EN/DIS pin and SMPTE_BYPASS pin must also be set HIGH. Set HIGH to disable. R/W 0 5 ILLEGAL_REMAP Illegal Code Remapping. Detection and correction of illegal code words within the active picture area (AP). The IOPROC_EN/DIS pin and SMPTE_BYPASS pin must also be set HIGH. Set HIGH to disable. R/W 0 4 EDH_CRC_INS Error Detection & Handling (EDH) Cyclical Redundancy Check (CRC) error correction. In SD mode the GS1531 will generate and insert EDH packets. The IOPROC_EN/DIS pin and SMPTE_BYPASS pin must also be set HIGH. Set HIGH to disable. R/W 0 3 ANC_CSUM_INS Ancillary Data Checksum insertion. The IOPROC_EN/DIS pin and SMPTE_BYPASS pin must also be set HIGH. Set HIGH to disable. R/W 0 2 CRC_INS Y and C line-based CRC insertion. In HD mode, line-based CRC words are inserted in both the Y and C channels. The IOPROC_EN/DIS pin and SMPTE_BYPASS pin must be also set HIGH. Set HIGH to disable R/W 0 1 LNUM_INS Y and C line number insertion - HD mode only. The IOPROC_EN/DIS pin and SMPTE_BYPASS pin must be set HIGH. Set HIGH to disable. R/W 0 0 TRS_INS Timing Reference Signal Insertion. Occurs only when IOPROC_EN/DIS is HIGH and SMPTE_BYPASS is HIGH. Set HIGH to disable. R/W 0 30573 - 7 February 2008 31 of 50 GS1531 Data Sheet 4.6.3.1 SMPTE 352M Payload Identifier Insertion The GS1531 can generate and insert SMPTE 352M payload identifier ancillary data packets into the data stream, based on information programmed into the host interface. When this feature is enabled, the device will automatically generate the ancillary data preambles, (DID, SDID, DBN, DC), and calculate the checksum. The SMPTE 352M packet will be inserted into the data stream according to the line numbers programmed in the LINE_352M registers (Table 4-6). The insertion process will only take place if one or more of the four VIDEO_FORMAT registers (Table 4-7) have been programmed with non-zero values. In addition, the GS1531 requires the 352M_INS bit of the IOPROC_DISABLE register be set LOW. NOTE 1: For the purpose of determining the line and pixel position for insertion, the GS1531 will differentiate between PsF and interlaced formats by interrogating bits 14 and 15 of the VIDEO_FORMAT_A register. The packets will be inserted immediately after the EAV word in SD video streams and immediately after the line-based CRC word in the Y channel of HD video streams. NOTE 2: It is the responsibility of the user to ensure that there is sufficient space in the horizontal blanking interval for the insertion of the SMPTE 352M packets. If there are other ancillary data packets present, the SMPTE 352M packet will be inserted in the first available location in the horizontal ancillary space. Ancillary data must be adjacent to the EAV in SD streams or to the line based-CRC in HD streams. Where there is insufficient space available, the 352M packets will not be inserted. Table 4-6: Host Interface Description for SMPTE 352M Packet Line Number Insertion Registers Register Name Bit Name Description LINE_352M_f1 Address: 01Bh 15-11 - Not Used. 10-0 LINE_0_352M[10:0] Line number where SMPTE352M packet is inserted in field 1. LINE_352M_f2 Address: 01Ch 15-11 - Not Used. 10-0 LINE_1_352M[10:0] Line number where SMPTE352M packet is inserted in field 2. 30573 - 7 February 2008 R/W Default - - R/W 0 - - R/W 0 32 of 50 GS1531 Data Sheet Table 4-7: Host Interface Description for SMPTE 352M Payload Identifier Registers Register Name Bit Name Description VIDEO_FORMAT_B Address: 00Bh 15-8 SMPTE352M Byte 4 7-0 SMPTE352M Byte 3 VIDEO_FORMAT_A Address: 00Ah 15-8 SMPTE352M Byte 2 7-0 SMPTE 352M Byte 1 R/W Default SMPTE 352M Byte 4 information must be programmed in this register when 352M_INS = LOW. R/W 0 SMPTE 352M Byte 3 information must be programmed in this register when 352M_INS = LOW. R/W 0 SMPTE 352M Byte 2 information must be programmed in this register when 352M_INS = LOW. R/W 0 SMPTE 352M Byte 1 information must be programmed in this register when 352M_INS = LOW. R/W 0 4.6.3.2 Illegal Code Remapping If the ILLEGAL_REMAP bit of the IOPROC_DISABLE register is set LOW, the GS1531 will remap all codes within the active picture between the values of 3FCh and 3FFh to 3FBh. All codes within the active picture area between the values of 000h and 003h will be remapped to 004h. In addition, 8-bit TRS and ancillary data preambles will be remapped to 10-bit values if this feature is enabled. 4.6.3.3 EDH Generation and Insertion When operating in SD mode, (SD/HD = HIGH), the GS1531 will generate and insert complete EDH packets into the data stream. Packet generation and insertion will only take place if the EDH_CRC_INS bit of the IOPROC_DISABLE register is set LOW. The GS1531 will generate all of the required EDH packet data including all ancillary data preambles, (DID, DBN, DC), reserved code words and checksum. Calculation of both full field (FF) and active picture (AP) CRC's will be carried out by the device. SMPTE RP165 specifies the calculation ranges and scope of EDH data for standard 525 and 625 component digital interfaces. The GS1531 will utilize these standard ranges by default. If the received video format does not correspond to 525 or 625 digital component video standards as determined by the flywheel pixel and line counters, then one of two schemes for determining the EDH calculation ranges will be employed: 1. Ranges will be based on the line and pixel ranges programmed by the host interface; or 2. In the absence of user-programmed calculation ranges, ranges will be determined from the received TRS ID words or supplied H, V, and F timing signals, see Internal Flywheel on page 25. 30573 - 7 February 2008 33 of 50 GS1531 Data Sheet The registers available to the host interface for programming EDH calculation ranges include active picture and full field line start and end positions for both fields. Table 4-8 shows the relevant registers, which default to '0' after device reset. If any or all of these register values are zero, then the EDH CRC calculation ranges will be determined from the flywheel generated H signal. The first active and full field pixel will always be the first pixel after the SAV TRS code word. The last active and full field pixel will always be the last pixel before the start of the EAV TRS code words. EDH error flags (EDH, EDA, IDH, IDA and UES) for ancillary data, full field and active picture will also be inserted. These flags must be programmed into the EDH_FLAG registers of the device (Table 4-9). NOTE 1: It is the responsibility of the user to ensure that the EDH flag registers are updated once per field. The prepared EDH packet will be inserted at the appropriate line of the video stream according to RP165. The start pixel position of the inserted packet will be based on the SAV position of that line such that the last byte of the EDH packet (the checksum) will be placed in the sample immediately preceding the start of the SAV TRS word. NOTE 2: It is also the responsibility of the user to ensure that there is sufficient space in the horizontal blanking interval for the EDH packet to be inserted. Table 4-8: Host Interface Description for EDH Calculation Range Registers Register Name Bit Name Description AP_LINE_START_F0 Address: 012h 15-10 - Not Used. 9-0 AP_LINE_START_F0[9:0] Field 0 Active Picture start line data used to set EDH calculation range outside of RP 165 values. AP_LINE_END_F0 Address: 013h 15-10 - Not Used. 9-0 AP_LINE_END_F0[9:0] Field 0 Active Picture end line data used to set EDH calculation range outside of RP 165 values. AP_LINE_START_F1 Address: 014h 15-10 - Not Used. 9-0 AP_LINE_START_F1[9:0] Field 1 Active Picture start line data used to set EDH calculation range outside of RP 165 values. AP_LINE_END_F1 Address: 015h 15-10 - Not Used. 9-0 AP_LINE_END_F1[9:0] Field 1 Active Picture end line data used to set EDH calculation range outside of RP 165 values. 30573 - 7 February 2008 R/W Default - - R/W 0 - - R/W 0 - - R/W 0 - - R/W 0 34 of 50 GS1531 Data Sheet Table 4-8: Host Interface Description for EDH Calculation Range Registers (Continued) Register Name Bit Name Description FF_LINE_START_F0 Address: 016h 15-10 - Not Used. 9-0 FF_LINE_START_F0[9:0] Field 0 Full Field start line data used to set EDH calculation range outside of RP 165 values. FF_LINE_END_F0 Address: 017h 15-10 - Not Used. 9-0 FF_LINE_END_F0[9:0] Field 0 Full Field end line data used to set EDH calculation range outside of RP 165 values. FF_LINE_START_F1 Address: 018h 15-10 - Not Used. 9-0 FF_LINE_START_F1[9:0] Field 1 Full Field start line data used to set EDH calculation range outside of RP-165 values. FF_LINE_END_F1 Address: 019h 15-10 - Not Used. 9-0 FF_LINE_END_F1[9:0] Field 1 Full Field end line data used to set EDH calculation range outside of RP-165 values. R/W Default - - R/W 0 - - R/W 0 - - R/W 0 - - R/W 0 R/W Default - - Table 4-9: Host Interface Description for EDH Flag Register Register Name Bit Name Description EDH_FLAG Address: 002h 15 - Not Used. 14 ANC-UES Ancillary Unknown Error Status flag will be generated and inserted when IOPROC_EN/DIS and SMPTE_BYPASS pins are HIGH and EDH_CRC_INS bit is LOW. SD mode only. R/W 0 13 ANC-IDA Ancillary Internal device error Detected Already flag will be generated and inserted when IOPROC_EN/DIS and SMPTE_BYPASS pins are HIGH and EDH_CRC_INS bit is LOW. SD mode only. R/W 0 12 ANC-IDH Ancillary Internal device error Detected Here flag will be generated and inserted when IOPROC_EN/DIS and SMPTE_BYPASS pins are HIGH and EDH_CRC_INS bit is LOW. SD mode only. R/W 0 11 ANC-EDA Ancillary Error Detected Already flag will be generated and inserted when IOPROC_EN/DIS and SMPTE_BYPASS pins are HIGH and EDH_CRC_INS bit is LOW. SD mode only. R/W 0 10 ANC-EDH Ancillary Error Detected Here flag will be generated and inserted when IOPROC_EN/DIS and SMPTE_BYPASS pins are HIGH and EDH_CRC_INS bit is LOW. SD mode only. R/W 0 30573 - 7 February 2008 35 of 50 GS1531 Data Sheet Table 4-9: Host Interface Description for EDH Flag Register (Continued) Register Name Bit Name Description R/W Default 9 FF-UES Full Field Unknown Error flag will be generated and inserted when IOPROC_EN/DIS and SMPTE_BYPASS pins are HIGH and EDH_CRC_INS bit is LOW. SD mode only. R/W 0 8 FF-IDA Full Field Internal device error Detected Already flag will be generated and inserted when IOPROC_EN/DIS and SMPTE_BYPASS pins are HIGH and EDH_CRC_INS bit is LOW. SD mode only. R/W 0 7 FF-IDH Full Field Internal device error Detected flag will be generated and inserted when IOPROC_EN/DIS and SMPTE_BYPASS pins are HIGH and EDH_CRC_INS bit is LOW. SD mode only. R/W 0 6 FF-EDA Full Field Error Detected Already flag will be generated and inserted when IOPROC_EN/DIS and SMPTE_BYPASS pins are HIGH and EDH_CRC_INS bit is LOW. SD mode only. R/W 0 5 FF-EDH Full Field Error Detected Here flag will be generated and inserted when IOPROC_EN/DIS and SMPTE_BYPASS pins are HIGH and EDH_CRC_INS bit is LOW. SD mode only. R/W 0 4 AP-UES Active Picture Unknown Error Status flag will be generated and inserted when IOPROC_EN/DIS and SMPTE_BYPASS pins are HIGH and EDH_CRC_INS bit is LOW. SD mode only. R/W 0 3 AP-IDA Active Picture Internal device error Detected Already flag will be generated and inserted when IOPROC_EN/DIS and SMPTE_BYPASS pins are HIGH and EDH_CRC_INS bit is LOW. SD mode only. R/W 0 2 AP-IDH Active Picture Internal device error Detected Here flag will be generated and inserted when IOPROC_EN/DIS and SMPTE_BYPASS pins are HIGH and EDH_CRC_INS bit is LOW. SD mode only. R/W 0 1 AP-EDA Active Picture Error Detected Already flag will be generated and inserted when IOPROC_EN/DIS and SMPTE_BYPASS pins are HIGH and EDH_CRC_INS bit is LOW. SD mode only. R/W 0 0 AP-EDH Active Picture Error Detected Here flag will be generated and inserted when IOPROC_EN/DIS and SMPTE_BYPASS pins are HIGH and EDH_CRC_INS bit is LOW. SD mode only. R/W 0 30573 - 7 February 2008 36 of 50 GS1531 Data Sheet 4.6.3.4 Ancillary Data Checksum Generation and Insertion The GS1531 will calculate checksums for all detected ancillary data packets presented to the device. These calculated checksum values are inserted into the data stream prior to serialization. Ancillary data checksum generation and insertion will only take place if the ANC_CSUM_INS bit of the IOPROC_DISABLE register is set LOW. 4.6.3.5 Line Based CRC Generation and Insertion The GS1531 will generate and insert line based CRC words into both the Y and C channels of the data stream. This feature is only available in HD mode and is enabled by setting the CRC_INS bit of the IOPROC_DISABLE register LOW. 4.6.3.6 HD Line Number Generation and Insertion In HD mode, the GS1531 will calculate and insert line numbers into the Y and C channels of the output data stream. Line number generation is in accordance with the relevant HD video standard as determined by the device, see Automatic Video Standard Detection on page 28. This feature is enabled when SD/HD = LOW, and the LNUM_INS bit of the IOPROC_DISABLE register is set LOW. 4.6.3.7 TRS Generation and Insertion The GS1531 can generate and insert 10-bit TRS code words into the data stream as required. This feature is enabled by setting the TRS_INS bit of the IOPROC_DISABLE register LOW. TRS word generation will be performed in accordance with the timing parameters generated by the flywheel which will be locked either to the received TRS ID words or the supplied H, V, and F timing signals, see Internal Flywheel on page 25. 4.7 Parallel-To-Serial Conversion The parallel data output of the internal data processing blocks is fed to the parallel-to-serial converter. The function of this block is to generate a serial data stream from the 10-bit or 20-bit parallel data words and pass the stream to the integrated cable driver. 30573 - 7 February 2008 37 of 50 GS1531 Data Sheet 4.8 Serial Digital Data PLL To obtain a clean clock signal for serialization and transmission, the input PCLK is locked to an external reference signal via the GS1531's integrated phase-locked loop. This high quality analog PLL allows the GS1531 to significantly attenuate jitter on the incoming PCLK. This PLL is also responsible for generating all internal clock signals required by the device. Internal division ratios for the locked PCLK are determined by the setting of the SD/HD and 20bit/10bit pins as shown in Table 4-10. Table 4-10: Serial Digital Output Rates Supplied PCLK Rate Serial Digital Output Rate Pin Settings SD/HD 20bit/10bit 74.25 or 74.25/1.001 MHz 1.485 or 1.485/1.001Gb/s LOW HIGH 148.5 or 148.5/1.001MHz 1.485 or 1.485/1.001Gb/s LOW LOW 13.5MHz 270Mb/s HIGH HIGH 27MHz 270Mb/s HIGH LOW 4.8.1 External VCO The GS1531 requires the GO1555/GO1525* external voltage controlled oscillator as part of its internal PLL. Power for the external VCO is generated entirely by the GS1531 from an integrated voltage regulator. The internal regulator uses +3.3V supplied on the CP_VDD / CP_GND pins to provide +2.5V on the VCO_VCC / VCO_GND pins. The external VCO produces a 1.485GHz reference signal for the PLL, input on the VCO pin of the device. Both reference and control signals should be referenced to the supplied VCO_GND as shown in the recommended application circuit of Typical Application Circuit on page 46. *For new designs use GO1555 4.8.2 Lock Detect Output The lock detect block controls the serial digital output signal and indicates the lock status of the device via the LOCKED output pin. LOCKED will be asserted HIGH if and only if the internal data PLL has locked the PCLK signal to the external VCO reference signal and one of the following is true: 1. The device is set to operate in SMPTE mode and has detected SMPTE TRS words in the serial stream; or 2. The device is set to operate in DVB-ASI mode and has detected K28.5 sync characters in the serial stream; or 30573 - 7 February 2008 38 of 50 GS1531 Data Sheet 3. The device is set to operate in Data-Through mode. 4.8.3 Loop Bandwidth Adjustment For new designs the GO1555 is recommended for use with the GS1531. The recommended loop bandwidth control component values are listed in Table 4-11 and can be seen in Section 5.1 Typical Application Circuit. Designs using the GO1525 VCO will require different loop bandwidth control components. The component values are listed in Table 4-11. Table 4-11: GO1555 Loop Bandwidth Adjustment Component GO1555 GO1525 LB_CONT 100nF 100nF RLF-CP_CAP 33 50 CP_CAP 47nF 22nF NOTE: When using the GS1531 with the GS4911B clock generator a narrower loop bandwidth for the GS1531 serializer should be used. For more details please refer to Section 2.5 of the GS4911B Reference Design. 4.9 Serial Digital Output The GS1531 contains an integrated current mode differential serial digital cable driver with automatic slew rate control. The integrated cable driver uses a separate power supply of +1.8V DC supplied via the CD_VDD and CD_GND pins. To enable the output, SDO_EN/DIS must be set HIGH. Setting the SDO_EN/DIS signal LOW will cause the SDO and SDO output pins to become high impedance, resulting in reduced device power consumption. Gennum recommends using the GS1528A SDI Dual Slew-Rate Cable Driver to meet SMPTE specifications. 4.9.1 Output Swing Nominally, the voltage swing of the serial digital output is 800mVp-p single-ended into a 75 load. This is set externally by connecting the RSET pin to CD_VDD through 281 . The output swing may be decreased by increasing the value of the RSET resistor. The relationship is approximated by the curve shown in Figure 4-4. Alternatively, the serial digital output swing can drive 800mVp-p into a 50 load. Since the output swing is reduced by a factor of approximately one third when the smaller load is used, the RSET resistor must be 187 to obtain 800mVp-p. 30573 - 7 February 2008 39 of 50 GS1531 Data Sheet 1000 VSDO(mVp-p) 900 800 700 600 75 load 500 50 load 400 300 200 250 300 350 400 450 500 550 600 650 700 RSET() Figure 4-4: Serial Digital Output Swing 4.9.2 Serial Digital Output Mute The GS1531 will automatically mute the serial digital output when the LOCKED output signal is LOW. In this case, the SDO and SDO signals are set to a constant voltage level. 4.10 GSPI Host Interface The GSPI, or Gennum Serial Peripheral Interface, is a 4-wire interface provided to allow the host to enable additional features of the device and /or to provide additional status information through configuration registers in the GS1531. The GSPI comprises a serial data input signal SDIN, serial data output signal SDOUT, an active low chip select CS, and a burst clock SCLK. The burst clock must have a duty cycle between 40% and 60%. Because these pins are shared with the JTAG interface port, an additional control signal pin JTAG/HOST is provided. When JTAG/HOST is LOW, the GSPI interface is enabled. When operating in GSPI mode, the SCLK, SDIN, and CS signals are provided by the host interface. The SDOUT pin is a high-impedance output allowing multiple devices to be connected in parallel and selected via the CS input. The interface is illustrated in the Figure 4-5 below. All read or write access to the GS1531 is initiated and terminated by the host processor. Each access always begins with a 16-bit command word on SDIN indicating the address of the register of interest. This is followed by a 16-bit data word on SDIN in write mode, or a 16-bit data word on SDOUT in read mode. 30573 - 7 February 2008 40 of 50 GS1531 Data Sheet Application Host GS1531 SCLK SCLK SDOUT SDIN CS SDIN CS SDOUT Figure 4-5: Gennum Serial Peripheral Interface (GSPI) 4.10.1 Command Word Description The command word is transmitted MSB first and contains a read/write bit, nine reserved bits and a 6-bit register address. Set R/W = '1' to read and R/W = '0' to write from the GSPI. Command words are clocked into the GS1531 on the rising edge of the serial clock SCLK. The appropriate chip select signal, CS, must be asserted low a minimum of 1.5ns (t0 in Figure 4-8 and Figure 4-9) before the first clock edge to ensure proper operation. Each command word must be followed by only one data word to ensure proper operation. 30573 - 7 February 2008 41 of 50 GS1531 Data Sheet MSB LSB R/W RSV RSV RSV RSV RSV RSV RSV RSV RSV A5 A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 Figure 4-6: Command Word MSB LSB D15 D14 D13 D12 D11 D9 D10 D8 Figure 4-7: Data Word 4.10.2 Data Read and Write Timing Read and write mode timing for the GSPI interface is shown in Figure 4-8 and Figure 4-9 respectively. The maximum SCLK frequency allowed is 6.6MHz. When writing to the registers via the GSPI, the MSB of the data word may be presented to SDIN immediately following the falling edge of the LSB of the command word. All SDIN data is sampled on the rising edge of SCLK. When reading from the registers via the GSPI, the MSB of the data word will be available on SDOUT 12ns (t5) following the falling edge of the LSB of the command word, and thus may be read by the host on the very next rising edge of the clock. The remaining bits are clocked out by the GS1531 on the negative edges of SCLK. duty cycle t2 t0 t4 t5 period SCLK CS t3 input data setup time RSV RSV t6 SDIN R/W RSV RSV RSV RSV RSV RSV RSV A4 A5 A3 A2 A1 output data hold time A0 SDOUT D15 D14 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 D13 Figure 4-8: GSPI Read Mode Timing t2 t0 duty cycle t4 period SCLK CS SDIN R/W RSV RSV RSV RSV t3 input data setup time RSV RSV RSV RSV RSV A5 A4 A3 A2 A1 A0 D15 D14 D13 Figure 4-9: GSPI Write Mode Timing 30573 - 7 February 2008 42 of 50 GS1531 Data Sheet 4.10.3 Configuration and Status Registers Table 4-12 summarizes the GS1531's internal status and configuration registers. All of these registers are available to the host via the GSPI and are all individually addressable. Where status registers contain less than the full 16 bits of information however, two or more registers may be combined at a single logical address. Table 4-12: GS1531 Internal Registers Address Register Name See Section 000h IOPROC_DISABLE Section 4.6.3 002h EDH_FLAG Section 4.6.3.3 004h VIDEO_STANDARD Section 4.6.2 00Ah - 00Bh VIDEO_FORMAT Section 4.6.3.1 00Eh - 011h RASTER_STRUCTURE Section 4.6.2 012h - 019h EDH_CALC_RANGES Section 4.6.3.3 01Bh - 01Ch LINE_352M Section 4.6.3.1 4.11 JTAG When the JTAG/HOST input pin of the GS1531 is set HIGH, the host interface port will be configured for JTAG test operation. In this mode, pins H4 to H6 and J6 become TMS, TCK, TDO, and TDI. In addition, the RESET_TRST pin will operate as the test reset pin. Boundary scan testing using the JTAG interface will be enabled in this mode. There are two methods in which JTAG can be used on the GS1531: 1. As a stand-alone JTAG interface to be used at in-circuit ATE (Automatic Test Equipment) during PCB assembly; or 2. Under control of the host for applications such as system power on self tests. When the JTAG tests are applied by ATE, care must be taken to disable any other devices driving the digital I/O pins. If the tests are to be applied only at ATE, this can be accomplished with tri-state buffers used in conjunction with the JTAG/HOST input signal. This is shown in Figure 4-10. 30573 - 7 February 2008 43 of 50 GS1531 Data Sheet Application HOST GS1531 CS_TMS SCLK_TCK SDIN_TDI SDOUT_TDO JTAG_HOST In-circuit ATE probe Figure 4-10: In-Circuit JTAG Alternatively, if the test capabilities are to be used in the system, the host may still control the JTAG/HOST input signal, but some means for tri-stating the host must exist in order to use the interface at ATE. This is represented in Figure 4-11. Application HOST GS1531 CS_TMS SCLK_TCK SDIN_TDI SDOUT_TDO JTAG_HOST Tri-State In-circuit ATE probe Figure 4-11: System JTAG Please contact your Gennum representative to obtain the BSDL model for the GS1531. 30573 - 7 February 2008 44 of 50 GS1531 Data Sheet 4.12 Device Power Up The GS1531 has a recommended power supply sequence. To ensure correct power up, power the CORE_VDD pins before the IO_VDD pins. Device pins may also be driven prior to power up without causing damage. To ensure that all internal registers are cleared upon power-up, the RESET_TRST signal must be held LOW for a minimum of 1ms after the core power supply has reached the minimum level specified in the DC Electrical Characteristics Table, Table 2-1. See Figure 4-12. 4.13 Device Reset In order to initialize all internal operating conditions to their default states the RESET_TRST signal must be held LOW for a minimum of treset = 1ms. When held in reset, all device outputs will be driven to a high-impedance state. +1.65V +1.8V CORE_VDD treset treset Reset Reset RESET_TRST Figure 4-12: Reset Pulse 30573 - 7 February 2008 45 of 50 GS1531 Data Sheet 5. Application Reference Design 5.1 Typical Application Circuit +3.3V GND_VCO 2 1 O/P NC VCC GND 8 10n GND_D 1u +1.8V +3.3V GND_VCO VCO_VCC CORE_VDD GND_VCO 10n 10n 7 VCTR GND 1u 10n IO_GND VCO_VCC GO1555 (GO1525) 5 GND_VCO GND 6 4 GND 3 IO_VDD IO_VDD 1u 10n GND_VCO CORE_GND 10n IO_GND GND_D +3.3V GND_D GND_VCO 0 +1.8V CP_VDD * Component values for GO1555. For GO1525 component values see Section 4.8.3 10n 1u 1u +3.3V 33* 47n* 0 CORE_VDD 10n IO_VDD 10n 0 CP_GND CORE_GND D o n o t p o p u l a t e R2 1u 10n VCO_VCC GND_VCO IO_GND R2 100n GND_D GND_A GND_D GND_VCO PD_VDD 10n CORE_GND CORE_GND CORE_VDD CORE_VDD IO_GND IO_GND IO_GND IO_VDD IO_VDD IO_VDD CP_VDD CP_GND PD_GND PD_VDD +1.8V CORE_GND F5 CORE_GND E5 CORE_VDD F6 CORE_VDD E6 IO_GND B8 IO_GND F8 IO_GND J8 IO_VDD A8 IO_VDD E8 IO_VDD K8 B2 B3 C3 C2 C1 B4 B1 A1 A2 A3 A4 A5 PD_GND SDO_EN/DIS DETECT_TRS JTAG/HOST GND_A 20bit/10bit J1 G1 H1 H2 SDO_EN/DIS DETECT_TRS 281 +/-1% +1.8V_A SMPTE_BYPASS SD/HD DVB_ASI SMPTE_BYPASS SD/HD DVB_ASI NOTE: SMPTE_BYPASS, SD/HD, DVB_ASI, and RC_BYP are INPUTS in slave mode (MASTER/SLAVE = LOW), and are OUTPUTS in master mode (MASTER/SLAVE = HIGH). SDIN_TDI SDOUT_TDO CS_TMS 10n RESET_TRST 20bit/10bit IOPROC_EN/DIS SDO_EN/DIS DETECT_TRS JTAG/HOST SMPTE_BYPASS SD/HD DVB_ASI SCLK_TCK SDIN_TDI SDOUT_TDO CS_TMS D4 C6 C7 G6 F4 G4 J5 B7 K6 G5 E4 D5 H5 J6 H6 H4 RESET_TRST 20bit/10bit IOPROC_EN/DIS SDO_EN/DIS DETECT_TRS JTAG/HOST SMPTE_BYPASS SD/HD DVB_ASI SCLK_TCK SDIN_TDI SDOUT_TDO CS_TMS LOCKED SCLK_TCK A6 B5 B6 C4 C5 D2 D3 D7 E3 SCLK_TCK GS1531 K1 RSET JTAG/HOST PCLK BLANK H V F DATA[19..0] A10 A9 B10 B9 C10 C9 D10 D9 E10 E9 F10 F9 G10 G9 H10 H9 J10 J9 K10 K9 D6 C8 D8 H7 A7 G8 H8 J7 K7 DATA19 DATA18 DATA17 DATA16 DATA15 DATA14 DATA13 DATA12 DATA11 DATA10 DATA9 DATA8 DATA7 DATA6 DATA5 DATA4 DATA3 DATA2 DATA1 DATA0 LOCK PCLK BLANK H V F E7 F2 F3 F7 G2 G3 G7 H3 J2 J3 J4 IOPROC_EN/DIS RESET_TRST IOPROC_EN/DIS SDO SDO CD_GND CD_VDD 20bit/10bit DIN19 DIN18 DIN17 DIN16 DIN15 DIN14 DIN13 DIN12 DIN11 DIN10 DIN9 DIN8 DIN7 DIN6 DIN5 DIN4 DIN3 DIN2 DIN1 DIN0 RSV K3 K4 K5 K2 RESET_TRST F1 D1 E2 E1 LB_CONT CP_CAP LF VCO_VCC VCO_GND VCO VCO CP_VDD CP_GND PD_GND PD_VDD GND_A SDIN_TDI SDOUT_TDO CS_TMS +1.8V_A 10n +1.8V_A 10n GND_A 50 50 GND_A LOCK To the GS1528A Cable Driver NOTE: See Gennum's Reference Design: "Interfacing the GS1532 to the GS1528 Multi-rate Cable Driver" PCLK BLANK H V F 30573 - 7 February 2008 LOCK 75 PCLK BLANK H V F 46 of 50 GS1531 Data Sheet 6. References & Relevant Standards SMPTE 125M Component video signal 4:2:2 - bit parallel interface SMPTE 260M 1125 / 60 high definition production system - digital representation and bit parallel interface SMPTE 267M Bit parallel digital interface - component video signal 4:2:2 16 x 9 aspect ratio SMPTE 274M 1920 x 1080 scanning analog and parallel digital interfaces for multiple picture rates SMPTE 291M Ancillary Data Packet and Space Formatting SMPTE 292M Bit-Serial Digital Interface for High-Definition Television Systems SMPTE 293M 720 x 483 active line at 59.94 Hz progressive scan production - digital representation SMPTE 296M 1280 x 720 scanning, analog and digital representation and analog interface SMPTE 352M Video Payload Identification for Digital Television Interfaces SMPTE RP165 Error Detection Checkwords and Status Flags for Use in Bit-Serial Digital Interfaces for Television SMPTE RP168 Definition of Vertical Interval Switching Point for Synchronous Video Switching 30573 - 7 February 2008 47 of 50 GS1531 Data Sheet 7. Package & Ordering Information 7.1 Package Dimensions 30573 - 7 February 2008 48 of 50 GS1531 Data Sheet 7.2 Packaging Data Parameter Value Package Type 11mm x 11mm 100-ball LBGA Package Drawing Reference JEDEC M0192 Moisture Saturation Level 3 Junction to Case Thermal Resistance, j-c 10.4C/W Junction to Air Thermal Resistance, j-a (at zero airflow) 37.1C/W Psi 0.4C/W Pb-free and RoHS compliant (GS1531-CBE2 only) Yes 7.3 Ordering Information Part Number Package Pb-free and RoHS Compliant Temperature Range GS1531-CBE2 100-ball BGA Yes 0C to 70C GS1531-CB 100-ball BGA No 0C to 70C 30573 - 7 February 2008 49 of 50 GS1531 Data Sheet 8. Revision History Version ECR PCN Date Changes and / or Modifications 1 134904 - November 2004 Changed interfacing resistor values between GS1531 and GS1528A on Typical Application Circuit. Added note for PCLK Jitter Tolerance. 2 136174 - March 2005 Update SCLK to show as a burst clock. Remove "Green" references. 3 136663 - May 2005 Updated the status of the VD_STD[4:0] and STD_LOCK and INT_PROGb bits following a device reset or the removal of the input PCLK. Changed the GSPI Input Data Hold Time to a minimum instead of a maximum. 4 136981 - July 2005 Added note on 59.94Hz and 60Hz formats to Table 4-4 on page 29. Corrected PCLK to Data Timing (Figure 4-1 on page 23). Changed note on ESD protection in Absolute Maximum Ratings on page 13. Corrected setup time and hold time labels in Table 2-2 on page 14 and Figure 4-1 on page 23. Converted to Data Sheet. 5 141995 41245 October 2006 Modified internal register addresses to hexidecimal values in Table 4-12.Specified that serializer can reject >300ps pclk jitter in Description section on page 1. Corrected IO_PROG pin setting typing error in Section 4.6.2.1. Corrected VIDEO_FORMAT register labels in description of bit 6 (352M_INS) in Table 4-5. 6 143759 42774 February 2007 Recommended GO1555 VCO for new designs. Updated Section 5.1 Typical Application Circuit. Added Section 4.8.3 Loop Bandwidth Adjustment. 7 148907 - February 2008 Changed register RASTER_STRUCTURE2 from 12 bits to 13 bits in Table 4-3: Host Interface Description for Raster Structure Registers. Changes related to DVB-ASI mode in Pin Descriptions, Section 4.2.2, Section 4.2.4, Table 4-1 & Section 4.4. Changed SMPTE 352 Lines from 13 to 10 in Table 4-4. CAUTION ELECTROSTATIC SENSITIVE DEVICES DO NOT OPEN PACKAGES OR HANDLE EXCEPT AT A STATIC-FREE WORKSTATION DOCUMENT IDENTIFICATION DATA SHEET The product is in production. Gennum reserves the right to make changes at any time to improve reliability, function or design, in order to provide the best product possible. GENNUM CORPORATION Mailing Address: P.O. Box 489, Stn. A, Burlington, Ontario, Canada L7R 3Y3 Shipping Address: 970 Fraser Drive, Burlington, Ontario, Canada L7L 5P5 Tel. +1 (905) 632-2996 Fax. +1 (905) 632-5946 GENNUM JAPAN CORPORATION Shinjuku Green Tower Building 27F, 6-14-1, Nishi Shinjuku, Shinjuku-ku, Tokyo, 160-0023 Japan Tel. +81 (03) 3349-5501, Fax. +81 (03) 3349-5505 GENNUM UK LIMITED 25 Long Garden Walk, Farnham, Surrey, England GU9 7HX Tel. +44 (0)1252 747 000 Fax +44 (0)1252 726 523 Gennum Corporation assumes no liability for any errors or omissions in this document, or for the use of the circuits or devices described herein. The sale of the circuit or device described herein does not imply any patent license, and Gennum makes no representation that the circuit or device is free from patent infringement. GENNUM and the G logo are registered trademarks of Gennum Corporation. (c) Copyright 2004 Gennum Corporation. All rights reserved. Printed in Canada. www.gennum.com 30573 - 7 February 2008 50 of 50 50