SVPSSeries Surface mount type OS-CON Line-up Image of case size Products list Packing specifications SMD type Packing specifications Radial lead type Recommended soldering condition Fundamental structure Characteristics Reliability The SVPS series is designed to have a longer life span than the SVP series. Recommended for products such as flat-screen TVs where extended life performance would be beneficial. Lead free-reflow is supported.2 Specifications Items Technical data Series system diagram Selection guide Guidelines and precautions for use Condition (V) - 4.0 6.3 10 16 20 25 Surge voltage (V) Room temperature 5.2 8.2 12 18 23 25 Category temperature range () Capacitance tolerance Surface mount type SVPS SVPS 120Hz/20 M : 20 120Hz/20 Please see the attached characteristics list Rated voltage applied, after 2 minutes Please see the attached characteristics list 100kHz to 300kHz/20 Please see the attached characteristics list SVPD SVPC SVPB SVPA SVQP Equivalent series resistance (ESR) Characteristics of impedance ratio at high temp. and low temp. -55 to 105 - () Leakage current1 SVPE Specifications Rated voltage Dissipation Factor (DF) SVPF Based the value at 100kHz, 20 105 Z/Z20 0.75 to 1.25 C/C Within 20% of the initial value 105, 5,000h, Rated voltage applied (25V 20V applied) Endurance Radial lead type SEPC SEQP SEP 60, 90 to 95% RH, 1,000h, No-applied voltage Damp heat(Steady state) Resistance to soldering heat2 0.75 to 1.25 -55 Z/Z20 SVP SEPF RoHS compliance Long life VPS (230 X 75s) DF Within 1.5 times of the initial limit ESR Within 1.5 times of the initial limit LC Within the initial limit C/C Within 20% of the initial value DF Within 1.5 times of the initial limit ESR Within 1.5 times of the initial limit LC Within the initial limit (after voltage processing) C/C Within 10% of the initial value DF Within 1.3 times of the initial limit ESR Within 1.3 times of the initial limit LC Within the initial limit (after voltage processing) 1 When measured values are questionable, measure after voltage processing mentioned below. Voltage processing: Apply voltage for 120 minutes at 105. The voltage to be applied is the rated voltage for 4.0-20V products, and 20V for 25V products. 2 Please refer to page 14 for reflow soldering conditions. Marking and dimensions 180 16 Series B6, C6, E7, F8 size is SVPS A5 is S on the side of rated capacitance Rated capacitance L Rated voltage P C SVPS Case No. W H 003 0.2max D Polarity marking Cathode (unit : mm) Size 0.5 code D R Size list RV F 10 15 22 33 39 47 68 82 100 120 150 180 220 270 330 470 680 38 L 0.1 -0.4 W A5 B6 C6 E7 F8 6.3 A5 B6 C6 10 A5 A5 B6 C6 E7F8 E7 F8 F8 16 C6 E7 F8 F8 C 0.2 R P 0.2 4.0 5.4 4.3 4.3 5.0 0.6 to 0.8 1.0 B6 5.0 5.9 5.3 5.3 6.0 0.6 to 0.8 1.4 C6 6.3 5.9 6.6 6.6 7.3 0.6 to 0.8 2.1 E7 8.0 6.9 8.3 8.3 9.0 0.6 to 0.8 3.2 F8 10.0 7.9 10.3 10.3 11.0 0.6 to 0.8 4.6 20 25 E7 B6 H 0.2 A5 RV : Rated voltage 4.0 0.2 C6 E7 SVPS series characteristics list B6 DF (% max) Leakage current (A)(max) After 2 minutes 10 10 220 700 10 50 10 15 200 740 10 75 6SVPS22M 6.3 22 200 740 12 69.3 4SVPS33M 4.0 33 200 740 15 66 16SVPS22M 16 22 90 1060 10 176 10SVPS33M 10 33 70 1100 12 165 Products list Packing specifications SMD type Packing specifications Radial lead type Recommended soldering condition Fundamental structure Characteristics 6SVPS47M 6.3 47 30 1970 12 300 4SVPS68M 4.0 68 30 1970 12 300 22 60 1450 10 88 SVPF SVPE 20 16SVPS39M 16 39 24 2460 12 300 10SVPS68M 10 68 30 2200 12 300 6.3 120 22 2570 12 300 4.0 4SVPS150M 150 22 2570 12 300 25SVPS10M 25 10 60 1500 10 125 20SVPS47M 20 47 45 1890 12 188 16SVPS82M 16 82 30 2760 12 262 10SVPS150MX 10 6SVPS220M 4SVPS270M F8 Allowable ripple current 100kHz(mArms)1 10SVPS15M 6SVPS120M E7 ESR(m) (max) 100kHz to 300kHz / 20 10SVPS10M 20SVPS22M C6 Rated capacitance (F) Image of case size 150 30 2760 12 500 6.3 220 22 3220 12 500 4.0 270 22 3220 12 500 16SVPS100M 16 100 35 2670 12 320 16SVPS180M 16 180 29 3430 12 576 10SVPS150M 10 150 30 3020 12 300 10SVPS330M 10 330 24 3770 12 660 6SVPS470M 6.3 470 20 4130 12 592 4SVPS680M 4.0 680 20 4130 12 544 Reliability Surface mount type A5 Rated voltage (V) Part number Series system diagram SVPS SVPS SVPD SVPC SVPB SVPA SVQP SVP SEPF Radial lead type Size code Guidelines and precautions for use Selection guide SVPS Series Technical data Surface mount type OS-CON Line-up SEPC SEQP SEP 1 The surface temperature of aluminum case top must not exceed 105. A rise in temperature due to self-heating by ripple current should be factored in. Recommended land pattern dimension of PWB (unit : mm) a b c A5 1.0 6.2 1.6 B6 1.4 7.4 1.6 C6 2.1 9.1 1.6 E7 2.8 11.1 1.9 F8 4.3 13.1 1.9 c Size code a b Frequency coefficient for ripple current Frequency Coefficient 120Hz < f < 1kHz 0.05 1kHz < f < 10kHz 0.3 10kHz < f < 100kHz 0.7 100kHz < f < 500kHz 1 39