Model X2A Rev. A SMT Crossover Description The X2A is a low profile crossover to intersect an RF and DC circuit trace in an easy to use surface mount package designed for frequencies up to 6 GHz. The X2A is ideal for any application where an RF circuit must intersect with a DC circuit without resorting to a multilayer PCB. Parts have been subjected to rigorous qualification testing and units are 100% tested. They are manufactured using materials with x and y thermal expansion coefficients compatible with common substrates such as FR4, G-10 and polyamide. ELECTRICAL SPECIFICATIONS** Features: * * * * * * * * DC - 6.0 GHz RF - DC Crossover Low Loss DC Isolation Surface Mountable Tape And Reel Convenient Package 100 % Tested Frequency Port Impedance Return Loss GHz Ohms dB Min DC - 2.5 2.5 - 4.0 4.0 - 6.0 50 50 50 20 20 15 Insertion Loss Power dB Max Watts C / Watt C 0.05 0.10 0.15 30 15 10 250.9 250.9 250.9 -55 to +85 -55 to +85 -55 to +85 JC Operating Temp. **Specification based on performance of unit properly installed on microstrip printed circuit boards with 50 nominal impedance. Specifications subject to change without notice. Outline Drawing Top View (Near-side) Side View Bottom View (Far-side) .049.005 [1.240.13] .200.010 [5.080.25] 2X .102.004 [2.590.10] GND 2X .056.004 [1.420.10] GND GND Pin 1a .200.010 [5.080.25] GND Pin 1b Pin 1a Pin 1b 4X .039.004 [1.000.10] GND GND 4X .033.008 SQ [0.830.20] Dimensions are in Inches [Millimeters] X2A Rev A Mechanical Outline Available on Tape and Reel For Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 544-2414 +44 2392-232392 Model X2A Rev. A Typical Performance: 0.5 GHz. to 6.0 GHz. Insertion Loss X2A 0.00 -20 -0.10 Insertion Loss (dB) Return Loss (dB) Return Loss X2A -10 -30 -40 -50 -60 500 -0.20 -0.30 -0.40 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 -0.50 500 1000 1500 2000 Frequency (MHz) When a surface mount crossover is mounted to a printed circuit board, the primary concerns are; insuring the RF pads of the device are in contact with the circuit trace of the PCB and insuring the ground plane of neither the component nor the PCB is in contact with the RF signal. Since the component is not symmetrical, the crossovers are specifically oriented in the tape and reel. An example of how the PCB footprint could look is shown below. In specific designs, the 50 lines need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. (315) 432-8909 (800) 544-2414 +44 2392-232392 3000 3500 4000 4500 5000 Frequency (MHz) Mounting In order for Xinger crossovers to work optimally, there must be 50 transmission lines leading to and from all of the RF ports. Also, there must be a very good ground to the corners of the crossover to insure proper electrical performance. If either of these two conditions are not satisfied, insertion loss, VSWR and isolation parameters may not meet published specifications. USA/Canada: Toll Free: Europe: 2500 Available on Tape and Reel For Pick and Place Manufacturing. Mounting Footprint To ensure proper electrical and thermal performance there must be a ground plane with 100% solder connection underneath the part .063 SQ TYP [1.60] .148 [3.75] Mutiple plated thru holes to ground 50 Transmission Line .034 TYP [0.86] DC Line Dimensions are in Inches [Millimeters] X2A Rev A Mounting Footprint 5500 6000