Product
Folder
Sample &
Buy
Technical
Documents
Tools &
Software
Support &
Community
LM8272
SNOS515F –OCTOBER 2000–REVISED AUGUST 2015
LM8272 Dual RRIO, High Output Current & Unlimited Cap Load
Op Amp in Miniature Package
1 Features 3 Description
The LM8272 is a Rail-to-Rail input and output Op
1(VS= 12V, TA= 25°C, Typical values unless Amp which can operate with a wide supply voltage
specified). range. This device has high output current drive,
• GBWP 15MHz greater than Rail-to-Rail input common mode voltage
• Wide supply voltage range 2.5 V to 24 V range, and unlimited capacitive load drive capability,
while requiring only 0.95mA/channel supply current. It
• Slew rate 15 V/µs is specifically designed to handle the requirements of
• Supply current/channel 0.95 mA flat panel TFT panel VCOM driver applications as well
• Cap load tolerance Unlimited as being suitable for other low power and medium
speed applications which require ease of use and
• Output short circuit current ±13 0mA enhanced performance over existing devices.
• Output current (1 V from rails) ±65 mA Greater than Rail-to-Rail input common mode voltage
• Input common mode voltage 0.3 V beyond rails range with 50 dB of Common Mode Rejection allows
• Input voltage noise 15 nV/√Hz high side and low side sensing among many
• Input current noise 1.4 pA/√Hz applications without concerns for exceeding the range
and with no compromise in accuracy. An
2 Applications exceptionally wide operating supply voltage range of
2.5 V to 24 V removes any concerns over
• TFT-LCD flat panel VCOM driver functionality under extreme conditions and offers
• A/D converter buffer flexibility of use in multitude of applications. In
• High side/low side sensing addition, most device parameters are insensitive to
power supply variations. This design enhancement is
• Headphone amplifier yet another step in simplifying its usage.
The LM8272 is offered in the 8-pin VSSOP package.
Device Information(1)
PART NUMBER PACKAGE BODY SIZE (NOM)
LM8272 VSSOP (8) 3.00 mm × 3.00 mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
Large Signal Step Response
Simplified Schematic for Various Cap. Load
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM8272
SNOS515F –OCTOBER 2000–REVISED AUGUST 2015
www.ti.com
Table of Contents
A) Input Stage:......................................................... 14
1 Features.................................................................. 17.2 B) Output Stage: ..................................................... 15
2 Applications ........................................................... 17.3 C) Output Voltage Swing Close to V−:.................... 15
3 Description............................................................. 17.4 Driving Capactive Loads:........................................ 16
4 Revision History..................................................... 27.5 Estimating the Output Voltage Swing ..................... 16
5 Pin Configuration and Functions......................... 37.6 Output Short Circuit Current and Dissipation
6 Specifications......................................................... 4Issues:...................................................................... 17
6.1 Absolute Maximum Ratings ...................................... 47.7 Other Application Hints:.......................................... 18
6.2 ESD Ratings.............................................................. 47.8 LM8272 Advantages:.............................................. 18
6.3 Recommended Operating Conditions....................... 48 Device and Documentation Support.................. 19
6.4 Thermal Information.................................................. 48.1 Community Resources............................................ 19
6.5 5V Electrical Characteristics ..................................... 58.2 Trademarks............................................................. 19
6.6 12V Electrical Characteristics ................................... 68.3 Electrostatic Discharge Caution.............................. 19
6.7 Typical Performance Characteristics ........................ 88.4 Glossary.................................................................. 19
7 Application and Implementation ........................ 14 9 Mechanical, Packaging, and Orderable
7.1 Block Diagram and Operational Description Information........................................................... 19
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision E (August 2014) to Revision F Page
• Changed pin 5 From: -IN B To: +IN B Non-Inverting Input B in the Pin Functions table....................................................... 3
• Changed pin 6 From: +IN B To: -IN B Inverting Input B in the Pin Functions table............................................................... 3
• Moved "Storage temperature range" to the Absolute Maximum Ratings(1)(2) ........................................................................ 4
• Changed Handling Ratings To: ESD Ratings ........................................................................................................................ 4
Changes from Revision D (March 2013) to Revision E Page
• Changed data sheet structure and organization. Added, updated, or renamed the following sections: Device
Information Table, Application and Implementation; Power Supply Recommendations; Mechanical, Packaging, and
Ordering Information. ............................................................................................................................................................. 1
• Deleted TJ= 25°C................................................................................................................................................................... 5
• Deleted TJ= 25°C .................................................................................................................................................................. 6
Changes from Revision C (March 2013) to Revision D Page
• Changed layout of National Data Sheet to TI format ........................................................................................................... 18
2Submit Documentation Feedback Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: LM8272
LM8272
www.ti.com
SNOS515F –OCTOBER 2000–REVISED AUGUST 2015
5 Pin Configuration and Functions
8-Pin VSSOP
Top View
Pin Functions
PIN I/O DESCRIPTION
NUMBER NAME
1 OUT A O Output A
2 -IN A I Inverting Input A
3 +IN A I Non-Inverting Input A
4 V- I Negative Supply
5 +IN B I Non-Inverting Input B
6 -IN B I Inverting Input B
7 OUT B O Output B
8 V+ I Positive Supply
Copyright © 2000–2015, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LM8272
LM8272
SNOS515F –OCTOBER 2000–REVISED AUGUST 2015
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings(1)(2)
over operating free-air temperature range (unless otherwise noted) MIN MAX UNIT
VIN Differential +/−10 V
Output Short Circuit Duration See(3)(4)
Supply Voltage (V+- V−) 27 V
Voltage at Input/Output pins V++0.3, V−−0.3 V
Junction Temperature(5) +150 °C
Storage temperature range, Tstg −65 +150 °C
Soldering Information: Infrared or Convection (20 sec.) 235 °C
Wave Soldering (10 sec.) 260 °C
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Rating indicate conditions for
which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test
conditions, see the Electrical Characteristics.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
(3) Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in
exceeding the maximum allowed junction temperature of 150°C.
(4) Output short circuit duration is infinite for VS ≤6 V at room temperature and below. For VS > 6 V, allowable short circuit duration is 1.5
ms.
(5) The maximum power dissipation is a function of TJ(max), RθJA, and TA. The maximum allowable power dissipation at any ambient
temperature is PD = (TJ(max) - TA)/ RθJA. All numbers apply for packages soldered directly onto a PC board.
6.2 ESD Ratings VALUE UNIT
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins(2) ±2000
V(ESD) Electrostatic discharge(1) V
Machine Model (MM)(3) ±200
(1) Human body model, 1.5 kΩin series with 100 pF. Machine Model, 0 Ωis series with 200 pF.
(2) JEDEC document JEP155 states that 2000-V HBM allows safe manufacturing with a standard ESD control process.
(3) JEDEC document JEP157 states that 200-V MM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted) MIN NOM MAX UNIT
Supply Voltage (V+- V−) 2.5 24 V
Operating Temperature Range(1) −40 +85 °C
(1) The maximum power dissipation is a function of TJ(max), RθJA, and TA. The maximum allowable power dissipation at any ambient
temperature is PD = (TJ(max) - TA)/ RθJA. All numbers apply for packages soldered directly onto a PC board.
6.4 Thermal Information DGK
THERMAL METRIC(1) UNIT
8 Pins
RθJA Junction-to-ambient thermal resistance(2) 235 °C/W
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
(2) The maximum power dissipation is a function of TJ(max), RθJA, and TA. The maximum allowable power dissipation at any ambient
temperature is PD = (TJ(max) - TA)/ RθJA. All numbers apply for packages soldered directly onto a PC board.
4Submit Documentation Feedback Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: LM8272
LM8272
www.ti.com
SNOS515F –OCTOBER 2000–REVISED AUGUST 2015
6.5 5V Electrical Characteristics
Unless otherwise specified, all limited ensured for V+= 5V, V−= 0V, VCM = 0.5V, VO= V+/2, and RL> 1MΩto V−.Boldface
limits apply at the temperature extremes.
PARAMETER TEST CONDITIONS TYP(1) LIMIT(2) UNIT
VOS Input Offset Voltage VCM = 0.5V & VCM = 4.5V +/−5 mV
+/−0.7 +/−7max
TC VOS Input Offset Average Drift VCM = 0.5V & VCM = 4.5V(3) +/−2 — µV/°C
IBInput Bias Current See (4) ±2.00 µA
—±2.70 max
IOS Input Offset Current 250 nA
20 400 max
CMRR Common Mode Rejection Ratio VCM stepped from 0V to 5V 64 dB
80 61 min
+PSRR Positive Power Supply Rejection Ratio V+from 4.5V to 13V 78 dB
100 74 min
CMVR Input Common-Mode Voltage Range CMRR > 50dB −0.1 V
−0.3 0.0 max
5.1 V
5.3 5.0 min
AVOL Large Signal Voltage Gain VO= 0.5 to 4.5V, 64 dB
80
RL= 10kΩto V+/2 60 min
VOOutput Swing RL= 10kΩto V−4.93 4.85 V
High min
ISOURCE = 5mA 4.85 4.70
Output Swing RL= 10kΩto V+215 250 mV
Low max
ISINK = 5mA 300 350
ISC Output Short Circuit Current Sourcing to V−100 —
VID = 200mV(5) mA
Sinking to V+100 —
VID =−200mV(5)
IOUT Output Current VID = ±200mV, VO= 1V from rails ±55 — mA
ISSupply Current (Both Channel) No load, VCM = 0.5V 2.3 mA
1.8 2.8 max
SR Slew Rate(6) AV= +1, VI= 5VPP 12 — V/µs
fuUnity Gain Frequency VI= 10mVp, RL= 2KΩto V+/2 7.5 — MHz
GBWP Gain-Bandwidth Product f = 50KHz 13 — MHz
PhimPhase Margin VI= 10mVp, RL= 2kΩto V+/2 55 — deg
enInput-Referred Voltage Noise f = 2KHz, RS= 50Ω15 — nV/√Hz
inInput-Referred Current Noise f = 2KHz 1.4 — pA/√Hz
fmax Full Power Bandwidth ZL= (20pF || 10kΩ) to V+/2 700 — kHz
(1) Typical Values represent the most likely parametric norm.
(2) All limits are ensured by testing or statistical analysis.
(3) Offset voltage average drift determined by dividing the change in VOS at temperature extremes into the total temperature change.
(4) Positive current corresponds to current flowing into the device.
(5) Short circuit test is a momentary test. Output short circuit duration is infinite for VS≤6V at room temperature and below. For VS> 6V,
allowable short circuit duration is 1.5ms.
(6) Slew rate is the slower of the rising and falling slew rates. Connected as a Voltage Follower.
Copyright © 2000–2015, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LM8272
LM8272
SNOS515F –OCTOBER 2000–REVISED AUGUST 2015
www.ti.com
6.6 12V Electrical Characteristics
Unless otherwise specified, all limited ensured for V+= 12V, V−= 0V, VCM = 6V, VO= 6V, and RL> 1MΩto V−.Boldface
limits apply at the temperature extremes.
PARAMETER TEST CONDITIONS TYP(1) LIMIT(2) UNIT
VOS Input Offset Voltage VCM = 0.5V & VCM = 11.5V +/−7 mV
+/−0.7 +/−9max
TC VOS Input Offset Average Drift VCM = 0.5V & VCM = 11.5V(3) +/−2 — µV/°C
IBInput Bias Current See (4) ±2.00 µA
—±2.80 max
IOS Input Offset Current 275 nA
30 550 max
CMRR Common Mode Rejection Ratio VCM stepped from 0V to 12V 74 dB
88 72 min
+PSRR Positive Power Supply Rejection Ratio V+from 4.5V to 13V, VCM = 0.5V 78 dB
100 74 min
−PSRR Negative Power Supply Rejection Ratio 85 — dB
CMVR Input Common-Mode Voltage Range CMRR > 50dB −0.1 V
−0.3 0max
12.1 V
12.3 12.0 min
AVOL Large Signal Voltage Gain VO= 1V to 11V 74 dB
83
RL= 10kΩto V+/2 70 min
VOOutput Swing RL10kΩto V+/2 11.8 11.7 V
High min
ISOURCE = 5mA 11.6 11.5
Output Swing RL= 10kΩto V+/2 0.25 0.3 V
Low max
ISINK = 5mA .40 .45
ISC Output Short Circuit Current Sourcing to V−130 110
VID = 200mV (5) mA
min
Sinking to V+130 110
VID = 200mV (5)
IOUT Output Current VID = ±200mV, VO= 1V from rails ±65 — mA
ISSupply Current (Both Channel) No load, VCM = 0.5V 2.4 mA
1.9 2.9 max
SR Slew Rate(6) AV= +1, VI= 10VPP, CL= 10pF 15 — V/µs
AV= +1, VI= 10VPP, CL= 0.1µF 1 —
ROUT Close Loop Output Resistance AV= +1, f = 100KHz 3 — Ω
fuUnity Gain Frequency VI= 10mVp, RL= 2kΩto V+/2 8 — MHz
GBWP Gain-Bandwidth Product f = 50KHz 15 — MHz
PhimPhase Margin VI= 10mVp, RL= 2kΩto V+/2 57 — Deg
GM Gain Margin VI= 10mVp, RL= 2kΩto V+/2 20 — dB
−3dB BW Small Signal -3db Bandwidth AV= +1, RL= 2kΩto V+/2 12.5 —
AV= +1, RL= 600Ωto V+/2 10.5 — MHz
AV= +10, RL= 600Ωto V+/2 1.0 —
(1) Typical Values represent the most likely parametric norm.
(2) All limits are ensured by testing or statistical analysis.
(3) Offset voltage average drift determined by dividing the change in VOS at temperature extremes into the total temperature change.
(4) Positive current corresponds to current flowing into the device.
(5) Short circuit test is a momentary test. Output short circuit duration is infinite for VS ≤6V at room temperature and below. For VS > 6V,
allowable short circuit duration is 1.5ms.
(6) Slew rate is the slower of the rising and falling slew rates. Connected as a Voltage Follower.
6Submit Documentation Feedback Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: LM8272
LM8272
www.ti.com
SNOS515F –OCTOBER 2000–REVISED AUGUST 2015
12V Electrical Characteristics (continued)
Unless otherwise specified, all limited ensured for V+= 12V, V−= 0V, VCM = 6V, VO= 6V, and RL> 1MΩto V−.Boldface
limits apply at the temperature extremes.
PARAMETER TEST CONDITIONS TYP(1) LIMIT(2) UNIT
enInput-Referred Voltage Noise f = 2KHz, RS= 50Ω15 — nV/√Hz
inInput-Referred Current Noise f = 2KHz 1.4 — pA/√Hz
fmax Full Power Bandwidth ZL= (20pF || 10kΩ) to V+/2 300 — kHz
THD+N Total Harmonic Distortion +Noise AV= +2, RL= 2kΩto V+/2 0.02% —
VO= 8VPP, VS= ±5V
CT Rej. Cross-Talk Rejection f = 5MHz, Driver RL= 10kΩto V+/2 68 — dB
Copyright © 2000–2015, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LM8272
LM8272
SNOS515F –OCTOBER 2000–REVISED AUGUST 2015
www.ti.com
6.7 Typical Performance Characteristics
Figure 1. VOS Distribution Figure 2. VOS vs. VCM for 3 Representative Units
Figure 3. VOS vs. VCM for 3 Representative Units Figure 4. VOS vs. VCM for 3 Representative Units
Figure 6. VOS vs. VSfor 3 Representative Units
Figure 5. VOS vs. VSfor 3 Representative Units
8Submit Documentation Feedback Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: LM8272
LM8272
www.ti.com
SNOS515F –OCTOBER 2000–REVISED AUGUST 2015
Typical Performance Characteristics (continued)
Figure 7. VOS vs. VSfor 3 Representative Units Figure 8. IBvs. VS
Figure 9. IBvs. VSFigure 10. ISvs. VCM
Figure 12. ISvs. VS
Figure 11. ISvs. VCM
Copyright © 2000–2015, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LM8272
LM8272
SNOS515F –OCTOBER 2000–REVISED AUGUST 2015
www.ti.com
Typical Performance Characteristics (continued)
Figure 14. CMRR vs. Frequency
Figure 13. ISvs. VS
Figure 15. +PSRR vs. Frequency Figure 16. −PSRR vs. Frequency
Figure 17. Open Loop Gain/Phase Figure 18. Closed Loop Frequency Response
for Various Supplies for Various Gains
10 Submit Documentation Feedback Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: LM8272
LM8272
www.ti.com
SNOS515F –OCTOBER 2000–REVISED AUGUST 2015
Typical Performance Characteristics (continued)
Figure 20. Closed Loop Frequency Response
Figure 19. Closed Loop Frequency Response for Various RL
for Various Gains
Figure 21. Maximum Output Swing vs. Load Figure 22. Maximum Output Swing vs. Frequency
(1% Distortion) (1% Distortion)
Figure 23. Closed Loop Small Signal Frequency Response Figure 24. Overshoot vs. Cap Load
for Various CL
Copyright © 2000–2015, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LM8272
LM8272
SNOS515F –OCTOBER 2000–REVISED AUGUST 2015
www.ti.com
Typical Performance Characteristics (continued)
Figure 26. VOUT from V+vs. ISOURCE
Figure 25. Settling Time (±1%) & Slew Rate vs. Cap Load
Figure 28. Step Response for Various Amplitudes
Figure 27. VOUT from V−vs. ISINK
Figure 29. Step Response for Various Amplitudes Figure 30. Large Signal Step Response
for Various Cap Loads
12 Submit Documentation Feedback Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: LM8272
LM8272
www.ti.com
SNOS515F –OCTOBER 2000–REVISED AUGUST 2015
Typical Performance Characteristics (continued)
Figure 31. THD+N vs. Input Amplitude Figure 32. Input Referred Noise Density
for Various Frequency
Figure 34. Crosstalk Rejection vs. Frequency
Figure 33. Closed Loop Output Impedance vs. Frequency
Copyright © 2000–2015, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: LM8272
LM8272
SNOS515F –OCTOBER 2000–REVISED AUGUST 2015
www.ti.com
7 Application and Implementation
7.1 Block Diagram and Operational Description
A) Input Stage:
As seen in Figure 35, the input stage consists of two distinct differential pairs (Q1-Q2 and Q3-Q4) in order to
accommodate the full Rail-to-Rail input common mode voltage range. The voltage drop across R5, R6, R7 and
R8 is kept to less than 200 mV in order to allow the input to exceed the supply rails. Q13 acts as a switch to
steer current away from Q3-Q4 and into Q1-Q2, as the input increases beyond 1.4 of V+. This in turn shifts the
signal path from the bottom stage differential pair to the top one and causes a subsequent increase in the supply
current.
In transitioning from one stage to another, certain input stage parameters (VOS, Ib, IOS, en, and in) are determined
based on which differential pair is “on” at the time. Input Bias current, Ib, will change in value and polarity as the
input crosses the transition region. In addition, parameter such as PSRR and CMRR which involve the input
offset voltage will also be effected by changes in VCM across the differential pair transition region.
Figure 35. Simplified Schematic Diagram
14 Submit Documentation Feedback Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: LM8272
LM8272
www.ti.com
SNOS515F –OCTOBER 2000–REVISED AUGUST 2015
Block Diagram and Operational Description
A) Input Stage: (continued)
The input stage is protected with the combination of R9-R10 and D1, D2, D3 and D4 against differential input
over-voltages. This fault condition could otherwise harm the differential pairs or cause offset voltage shift in case
of prolonged over voltage. As shown in Figure 36, if this voltage reaches approximately ±1.4V at 25°C, the
diodes turn on and current flow is limited by the internal series resistors (R9 and R10). The Absolute Maximum
Rating of ±10V differential on VIN still needs to be observed. With temperature variation, the point were the
diodes turn on will change at the rate of 5mV/°C
Figure 36. Input Stage Current vs. Differential Input Voltage
7.2 B) Output Stage:
The output stage (see Figure 35) is comprised of complimentary NPN and PNP common-emitter stages to permit
voltage swing to within a Vce(sat) of either supply rail. Q9 supplies the sourcing and Q10 supplies the sinking
current load. Output current limiting is achieved by limiting the Vce of Q9 and Q10. Using this approach to current
limiting alleviates the drawback to the conventional scheme which requires one Vbe reduction in output swing.
The frequency compensation circuit includes Miller capacitors from collector to base of each output transistor
(see Figure 35, Ccomp9 and Ccomp10). At light capacitive loads, the high frequency gain of the output transistors is
high, and the Miller effect increases the effective value of the capacitors thereby stabilizing the Op Amp. Large
capacitive loads greatly decrease the high frequency gain of the output transistors thus lowering the effective
internal Miller capacitance - the internal pole frequency increases at the same time a low frequency pole is
created at the Op Amp output due to the large load capacitor. In this fashion, the internal dominant pole
compensation, which works by reducing the loop gain to less than 0dB when the phase shift around the feedback
loop is more than 180°, varies with the amount of capacitive load and becomes less dominant when the load
capacitor has increased enough. Hence the Op Amp is very stable even at high values of load capacitance
resulting in the uncharacteristic feature of stability under all capacitive loads.
7.3 C) Output Voltage Swing Close to V−:
The LM8272's output stage design allows voltage swings to within millivolts of either supply rail for maximum
flexibility and improved useful range. Because of this design architecture, as can be seen from Figure 35
diagram, with Output approaching either supply rail, either Q9 or Q10 Collector-Base junction reverse bias will
decrease. With output less than a Vbe from either rail, the corresponding output transistor operates near
saturation. In this mode of operation, the transistor will exhibit higher junction capacitance and lower ftwhich will
reduce Phase Margin. With the Noise Gain (NG = 1 + Rf/Rg, Rf & Rg are external gain setting resistors) of 2 or
higher, there is sufficient Phase Margin that this reduction (in Phase Margin) is of no consequence. However,
with lower Noise Gain (<2) and with less than 150mV voltage to the supply rail, if the output loading is light, the
Phase Margin reduction could result in unwanted oscillations.
Copyright © 2000–2015, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Links: LM8272
LM8272
SNOS515F –OCTOBER 2000–REVISED AUGUST 2015
www.ti.com
C) Output Voltage Swing Close to V−: (continued)
In the case of the LM8272, due to inherent architectural specifics, the oscillation occurs only with respect to Q10
when output swings to within 150mV of V−. However, if Q10 collector current is larger than its idle value of a few
microamps, the Phase Margin loss becomes insignificant. In this case, 300µA is the required Q10 collector
current to remedy this situation. Therefore, when all the aforementioned critical conditions are present at the
same time (NG < 2, VOUT < 150mV from supply rails, & output load is light) it is possible to ensure stability by
adding a load resistor to the output to provide the necessary Q10 minimum Collector Current (300µA).
For 12V (or ±6V) operation, for example, add a 39kΩresistor from the output to V+to cause 300µA output
sinking current and ensure stability. This is equivalent to about 15% increase in total quiescent power dissipation.
7.4 Driving Capactive Loads:
The LM8272 is specifically designed to drive unlimited capacitive loads without oscillations (see Figure 25). In
addition, the output current handling capability of the device allows for good slewing characteristics even with
large capacitive loads (Settling Time and Slew Rate vs. Cap Load plot). The combination of these features is
ideal for applications such as TFT flat panel buffers, A/D converter input amplifiers, etc.
However, as in most Op Amps, addition of a series isolation resistor between the Op Amp and the capacitive
load improves the settling and overshoot performance.
Output current drive is an important parameter when driving capacitive loads. This parameter will determine how
fast the output voltage can change. Referring to Figure 25, two distinct regions can be identified. Below about
10,000pF, the output Slew Rate is solely determined by the Op Amp's compensation capacitor value and
available current into that capacitor. Beyond 10nF, the Slew Rate is determined by the Op Amp's available output
current. An estimate of positive and negative slew rates for loads larger than 100nF can be made by dividing the
short circuit current value by the capacitor.
7.5 Estimating the Output Voltage Swing
It is important to keep in mind that the steady state output current will be less than the current available when
there is an input overdrive present. For steady state conditions, Figure 37 and Figure 38 plots can be used to
predict the output swing. These plots also show several load lines corresponding to loads tied between the
output and ground. In each case, the intersection of the device plot at the appropriate temperature with the load
line would be the typical output swing possible for that load. For example, a 600-Ωload can accommodate an
output swing to within 100mV of V−and to 250mV of V+(VS= ±5V) corresponding to a typical 9.65VPP unclipped
swing.
Figure 37. Steady State Output Sourcing Characteristics with Load Lines
16 Submit Documentation Feedback Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: LM8272
LM8272
www.ti.com
SNOS515F –OCTOBER 2000–REVISED AUGUST 2015
Estimating the Output Voltage Swing (continued)
Figure 38. Steady State Output Sinking Characteristics with Load Lines
7.6 Output Short Circuit Current and Dissipation Issues:
The LM8272 output stage is designed for maximum output current capability. Even though momentary output
shorts to ground and either supply can be tolerated at all operating voltages, longer lasting short conditions can
cause the junction temperature to rise beyond the absolute maximum rating of the device, especially at higher
supply voltage conditions. Below supply voltage of 6V, output short circuit condition can be tolerated indefinitely.
With the Op Amp tied to a load, the device power dissipation consists of the quiescent power due to the supply
current flow into the device, in addition to power dissipation due to the load current. The load portion of the
power itself could include an average value (due to a DC load current) and an AC component. DC load current
would flow if there is an output voltage offset, or if the output AC average current is non-zero, or if the Op Amp
operates in a single supply application where the output is maintained somewhere in the range of linear
operation. Therefore:
Ptotal = PQ+ PDC + PAC (1)
PQ= IS· VS(Op Amp Quiescent Power Dissipation) (2)
PDC = IO· (Vr- Vo) (DC Load Power) (3)
PAC = See Table 1 below (AC Load Power)
where:
• IS: Supply Current
• VS: Total Supply Voltage (V+- V−)
• VO: Average Output Voltage
• Vr: V+for sourcing and V−for sinking current
Table 1 below shows the maximum AC component of the load power dissipated by the Op Amp for standard
Sinusoidal, Triangular, and Square Waveforms:
Table 1. Normalized AC Power Dissipated in the Output Stage for Standard Waveforms
PAC (W.Ω/V2)
SINUSOIDAL TRIANGULAR SQUARE
50.7 × 10−346.9 × 10−362.5 × 10−3
Copyright © 2000–2015, Texas Instruments Incorporated Submit Documentation Feedback 17
Product Folder Links: LM8272
LM8272
SNOS515F –OCTOBER 2000–REVISED AUGUST 2015
www.ti.com
The table entries are normalized to VS2/RL. To figure out the AC load current component of power dissipation,
simply multiply the table entry corresponding to the output waveform by the factor VS2/RL. For example, with
±12V supplies, a 600Ωload, and triangular waveform power dissipation in the output stage is calculated as:
PAC = (46.9 × 10−3) · [242/600] = 45.0mW (4)
7.7 Other Application Hints:
The use of supply decoupling is mandatory in most applications. As with most relatively high speed/high output
current Op Amps, best results are achieved when each supply line is decoupled with two capacitors; a small
value ceramic capacitor (∼0.01µF) placed very close to the supply lead in addition to a large value Tantalum or
Aluminum (> 4.7µF). The large capacitor can be shared by more than one device if necessary. The small
ceramic capacitor maintains low supply impedance at high frequencies while the large capacitor will act as the
charge “bucket” for fast load current spikes at the Op Amp output. The combination of these capacitors will
provide supply decoupling and will help keep the Op Amp oscillation free under any load.
7.8 LM8272 Advantages:
Compared to other Rail-to-Rail Input/Output devices, the LM8272 offers several advantages such as:
• Improved cross over distortion
• Nearly constant supply current throughout the output voltage swing range and close to either rail.
• Nearly constant Unity gain frequency (fu) and Phase Margin (Phim) for all operating supplies and load
conditions.
• No output phase reversal under input overload condition.
18 Submit Documentation Feedback Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: LM8272
LM8272
www.ti.com
SNOS515F –OCTOBER 2000–REVISED AUGUST 2015
8 Device and Documentation Support
8.1 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
8.2 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
8.3 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
8.4 Glossary
SLYZ022 —TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
9 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2000–2015, Texas Instruments Incorporated Submit Documentation Feedback 19
Product Folder Links: LM8272
PACKAGE OPTION ADDENDUM
www.ti.com 29-Jul-2015
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM8272MM NRND VSSOP DGK 8 1000 TBD Call TI Call TI -40 to 85 A60
LM8272MM/NOPB ACTIVE VSSOP DGK 8 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 A60
LM8272MMX/NOPB ACTIVE VSSOP DGK 8 3500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 A60
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
PACKAGE OPTION ADDENDUM
www.ti.com 29-Jul-2015
Addendum-Page 2
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LM8272MM VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LM8272MM/NOPB VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LM8272MMX/NOPB VSSOP DGK 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 29-Jul-2015
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM8272MM VSSOP DGK 8 1000 210.0 185.0 35.0
LM8272MM/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0
LM8272MMX/NOPB VSSOP DGK 8 3500 367.0 367.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 29-Jul-2015
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
