Available on Tape
and Reel for Pick and
Place Manufacturing.
USA/Canada:
Toll Free:
Europe
:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Model X3C19P1-04S
Rev D
4dB Directional Coupler
Description
The X3C19P1-04S is a low profile, high performance 4dB directional
coupler in a new easy to use, manufacturing friendly surface mount
package. It is designed for DC, WCDMA, LTE and PCS applications.
The X3C19P1-04S is designed particularly for non-binary split and
combine in high power amplifiers, e.g. used along with a 3dB to get a
3-way, plus other signal distribution applications where low insertion
loss is required. It can be used in high power applications up to 70
Watts.
Parts have been subjected to rigorous qualification testing and they are
manufactured using materials with coefficients of thermal expansion
(CTE) compatible with common substrates such as FR4, G-10, RF-35,
RO4003 and polyimide. Produced with 6 of 6 RoHS compliant tin
immersion finish
Electrical Specifications
**
Features:
1500-2000MHz
DCS,PCS, WCDMA and LTE
High Power
Very Low Loss
Tight Coupling
High Directivity
Production Friendly
Tape and Reel
Lead Free
Frequency Mean
Coupling
Insertion
Loss VSWR Phase
Balance
MHz dB dB Max Max : 1 Degrees
1500-1700
1700-2000
4.0 ± 0.3
4.0 ± 0.3
0.15
0.15
1.22
1.22
904.0
904.0
1805-1880 4.0 ± 0.2 0.13 1.15 903.0
1930-1990 4.0 ± 0.2 0.14 1.15 903.0
Directivity Frequency
Sensitivity Power JC Operating
Temp.
dB Min dB Max Avg. CW Watts ºC/Watt ºC
20
20
± 0.25
± 0.25
70
70
25
25
-55 to +95
-55 to +95
23 ± 0.05 70 25 -55 to +95
23 ± 0.05 70 25 -55 to +95
**Specification based on performance of unit properly installed on Anaren Test Board 54147-0001. Refer to
Specifications subject to change without notice. Refer to parameter definitions for details.
Mechanical Outline
.250
±.010
[6.35
±0.25
]
.200
±.010
[5.08
±0.25
]
Pin 2Pin 1
Pin 3Pin 4 Denotes Array
Row (RR) &
Column (CC)
Orientation Mark
Denotes Pin 1
.045
±.005
[1.13
±0.14
]
Pin 2 Pin 1
Pin 3 Pin 4
GND
4X .020
±.004
[0.51
±0.10
]
GND 4X .020
±.004
[0.51
±0.10
]
4X .034
±.004
SQ
[0.86
±0.10
]
.170
±.004
[4.32
±0.10
]
.120
±.004
[3.05
±0.10
]
Dimensions are in Inches [Millimeters]
X3C19P1-04S Mechanical Outline
Tolerance are Non-cumulative
RR
-04S
19P1
CC
X3C
USA/Canada:
Toll Free:
Europe:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Available on Tape and
Reel for Pick and Place
Manufacturing.
Model X3C19P1-04S
Rev D
Directional Coupler Pin Configuration
The X3C19P1-04S has an orientation marker to denote Pin 1. Once port one has been identified the other ports are
known automatically. Please see the chart below for clarification:
Pin 1 Pin 2 Pin 3 Pin 4
Input Isolated Direct Coupled
Isolated Input Coupled Direct
Direct Coupled Input Isolated
Coupled Direct Isolated Input
Note: The direct port has a DC connection to the input port and the coupled port has a DC connection to the
isolated port.
Available on Tape
and Reel for Pick and
Place Manufacturing.
USA/Canada:
Toll Free:
Europe
:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Model X3C19P1-04S
Rev D
Insertion Loss and Power Derating Curves
Insertion Loss Derating:
The insertion loss, at a given frequency, of a group of
couplers is measured at 25C and then averaged. The
measurements are performed under small signal conditions
(i.e. using a Vector Network Analyzer). The process is
repeated at 95C and 150C. A best-fit line for the
measured data is computed and then plotted from -55C to
150C.
Power Derating:
The power handling and corresponding power derating
plots are a function of the thermal resistance, mounting
surface temperature (base plate temperature), maximum
continuous operating temperature of the coupler, and the
thermal insertion loss. The thermal insertion loss is
defined in the Power Handling section of the data sheet.
As the mounting interface temperature approaches the
maximum continuous operating temperature, the power
handling decreases to zero.
If mounting temperature is greater than 95C, Xinger
coupler will perform reliably as long as the input power
is derated to the curve above.
USA/Canada:
Toll Free:
Europe:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Available on Tape and
Reel for Pick and Place
Manufacturing.
Model X3C19P1-04S
Rev D
Typical Performance (-55°C, 25°C and 95°C): 1700-2000 MHz
1700 1750 1800 1850 1900 1950 2000
-50
-40
-30
-20
-10
0
Frequency (MHz)
Return Loss (dB)
Return Loss for X3C19P1-04S (Feeding Port 1)
-55ºC
25ºC
95ºC
1700 1750 1800 1850 1900 1950 2000
-50
-40
-30
-20
-10
0
Frequency (MHz)
Return Loss (dB)
Return Loss for X3C19P1-04S (Feeding Port 2)
-55ºC
25ºC
95ºC
1700 1750 1800 1850 1900 1950 2000
-50
-40
-30
-20
-10
0
Frequency (MHz)
Return Loss (dB)
Return Loss for X3C19P1-04S (Feeding Port 3)
-55ºC
25ºC
95ºC
1700 1750 1800 1850 1900 1950 2000
-50
-40
-30
-20
-10
0
Frequency (MHz)
Return Loss (dB)
Return Loss for X3C19P1-04S (Feeding Port 4)
-55ºC
25ºC
95ºC
Available on Tape
and Reel for Pick and
Place Manufacturing.
USA/Canada:
Toll Free:
Europe
:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Model X3C19P1-04S
Rev D
Typical Performance (-55°C, 25°C and 95°C): 1700-2000 MHz
1700 1750 1800 1850 1900 1950 2000
-4.4
-4.2
-4
-3.8
-3.6
Frequency (MHz)
Coupling (dB)
Coupling for X3C19P1-04S (Feeding Port 1)
-55ºC
25ºC
95ºC
1700 1750 1800 1850 1900 1950 2000
-50
-40
-30
-20
-10
0
Frequency (MHz)
Directivity (dB)
Directivity for X3C19P1-04S (Feeding Port 1)
-55ºC
25ºC
95ºC
1700 1750 1800 1850 1900 1950 2000
-0.2
-0.18
-0.16
-0.14
-0.12
-0.1
-0.08
-0.06
-0.04
-0.02
0
Frequency (MHz)
Insertion Loss (dB)
Insertion Loss for X3C19P1-04S (Feeding Port 1)
-55ºC
25ºC
95ºC
1700 1750 1800 1850 1900 1950 2000
-4
-2
0
2
4
Frequency (MHz)
Phase Balance (deg)
Phase Balance for X3C19P1-04S (Feeding Port 1)
-55ºC
25ºC
95ºC
USA/Canada:
Toll Free:
Europe:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Available on Tape and
Reel for Pick and Place
Manufacturing.
Model X3C19P1-04S
Rev D
Definition of Measured Specifications
Parameter Definition Mathematical Representation
VSWR
(Voltage Standing Wave Ratio)
The impedance match of
the coupler to a 50
system. A VSWR of 1:1
is optimal.
VSWR =
min
max
V
V
Vmax = voltage maxima of a standing wave
Vmin = voltage minima of a standing wave
Return Loss
The impedance match of
the coupler to a 50
system. Return Loss is
an alternate means to
express VSWR.
Return Loss (dB)= 20log
1-VSWR
1VSWR
Mean Coupling
At a given frequency
(
n
), coupling is the input
power divided by the
power at the coupled
port. Mean coupling is
the average value of the
coupling values in the
band. N is the number
of frequencies in the
band.
Coupling (dB) =
)(
)(
log10)(
ncpl
nin
n
P
P
C
Mean Coupling (dB) =
N
C
N
n
n
1
)(
Insertion Loss
The input power divided
by the sum of the power
at the two output ports.
10log
direct cpl
in
PP
P
Directivity
The power at the
coupled port divided by
the power at the isolated
port.
10log
iso
cpl
P
P
Phase Balance
The difference in phase
angle between the two
output ports.
Phase at coupled port – Phase at direct port
Frequency Sensitivity
The decibel difference
between the maximum in
band coupling value and
the mean coupling, and
the decibel difference
between the minimum in
band coupling value and
the mean coupling.
Max Coupling (dB) – Mean Coupling (dB)
and
Min Coupling (dB) – Mean Coupling (dB)
Available on Tape
and Reel for Pick and
Place Manufacturing.
USA/Canada:
Toll Free:
Europe
:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Model X3C19P1-04S
Rev D
USA/Canada:
Toll Free:
Europe:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Available on Tape and
Reel for Pick and Place
Manufacturing.
Model X3C19P1-04S
Rev D
Notes on RF Testing and Circuit Layout
The X3C19P1-04S Surface Mount Couplers require the use of a test fixture for verification of RF performance. This test
fixture is designed to evaluate the coupler in the same environment that is recommended for installation. Enclosed
inside the test fixture, is a circuit board that is fabricated using the recommended footprint. The part being tested is
placed into the test fixture and pressure is applied to the top of the device using a pneumatic piston. A four port Vector
Network Analyzer is connected to the fixture and is used to measure the S-parameters of the part. Worst case values
for each parameter are found and compared to the specification. These worst case values are reported to the test
equipment operator along with a Pass or Fail flag. See the illustrations below.
3dB, 4dB and 5dB
Test Board Test Board
In Fixture
Test Station
Available on Tape
and Reel for Pick and
Place Manufacturing.
USA/Canada:
Toll Free:
Europe
:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Model X3C19P1-04S
Rev D
The effects of the test fixture on the measured data must be minimized in order to accurately determine the performance
of the device under test. If the line impedance is anything other than 50 and/or there is a discontinuity at the microstrip
to SMA interface, there will be errors in the data for the device under test. The test environment can never be “perfect”,
but the procedure used to build and evaluate the test boards (outlined below) demonstrates an attempt to minimize the
errors associated with testing these devices. The lower the signal level that is being measured, the more impact the
fixture errors will have on the data. Parameters such as Return Loss and Isolation/Directivity, which are specified as
low as 27dB and typically measure at much lower levels, will present the greatest measurement challenge.
The test fixture errors introduce an uncertainty to the measured data. Fixture errors can make the performance of the
device under test look better or worse than it actually is. For example, if a device has a known return loss of 30dB and
a discontinuity with a magnitude of –35dB is introduced into the measurement path, the new measured Return Loss
data could read anywhere between –26dB and –37dB. This same discontinuity could introduce an insertion phase error
of up to 1.
There are different techniques used throughout the industry to minimize the affects of the test fixture on the
measurement data. Anaren uses the following design and de-embedding criteria:
Test boards have been designed and parameters specified to provide trace impedances of 50
1. Furthermore, discontinuities at the SMA to microstrip interface are required to be less than
–35dB and insertion phase errors (due to differences in the connector interface discontinuities and
the electrical line length) should be less than 0.50 from the median value of the four paths.
A “Thru” circuit board is built. This is a two port, microstrip board that uses the same SMA to
microstrip interface and has the same total length (insertion phase) as the actual test board. The
“Thru” board must meet the same stringent requirements as the test board. The insertion loss and
insertion phase of the “Thru” board are measured and stored. This data is used to completely de-
embed the device under test from the test fixture. The de-embedded data is available in S-
parameter form on the Anaren website (www.anaren.com).
Note: The S-parameter files that are available on the anaren.com website include data for frequencies that are outside
of the specified band. It is important to note that the test fixture is designed for optimum performance through 2.3GHz.
Some degradation in the test fixture performance will occur above this frequency and connector interface discontinuities
of –25dB or more can be expected. This larger discontinuity will affect the data at frequencies above 2.3GHz.
Circuit Board Layout
The dimensions for the Anaren test board are shown below. The test board is printed on Rogers RO4003 material that
is 0.032” thick. Consider the case when a different material is used. First, the pad size must remain the same to
accommodate the part. But, if the material thickness or dielectric constant (or both) changes, the reactance at the
interface to the coupler will also change. Second, the linewidth required for 50 will be different and this will introduce
a step in the line at the pad where the coupler interfaces with the printed microstrip trace. Both of these conditions will
affect the performance of the part. To achieve the specified performance, serious attention must be given to the
design and layout of the circuit environment in which this component will be used.
If a different circuit board material is used, an attempt should be made to achieve the same interface pad reactance
that is present on the Anaren RO4003 test board. When thinner circuit board material is used, the ground plane will be
closer to the pad yielding more capacitance for the same size interface pad. The same is true if the dielectric constant
of the circuit board material is higher than is used on the Anaren test board. In both of these cases, narrowing the line
before the interface pad will introduce a series inductance, which, when properly tuned, will compensate for the extra
capacitive reactance. If a thicker circuit board or one with a lower dielectric constant is used,
USA/Canada:
Toll Free:
Europe:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Available on Tape and
Reel for Pick and Place
Manufacturing.
Model X3C19P1-04S
Rev D
the interface pad will have less capacitive reactance than the Anaren test board. In this case, a wider section of line
before the interface pad (or a larger interface pad) will introduce a shunt capacitance and when properly tuned will
match the performance of the Anaren test board.
Notice that the board layout for the 3dB, 4dB and 5dB couplers is different from that of the 10dB and 20dB couplers.
The test board for the 3dB, 4dB and 5dB couplers has all four traces interfacing with the coupler at the same angle.
The test board for the 10dB and 20dB couplers has two traces approaching at one angle and the other two traces at a
different angle. The entry angle of the traces has a significant impact on the RF performance and these parts
have been optimized for the layout used on the test boards shown below.
3dB, 4dB and 5dB Test Board
Testing Sample Parts Supplied on Anaren Test Boards
If you have received a coupler installed on an Anaren produced microstrip test board, please remember to remove the
loss of the test board from the measured data. The loss is small enough that it is not of concern for Return Loss and
Isolation/Directivity, but it should certainly be considered when measuring coupling and calculating the insertion loss of
the coupler. An S-parameter file for a “Thru” board (see description of “Thru” board above) will be supplied upon request.
As a first order approximation, one should consider the following loss estimates:
Frequency Band
Avg. Ins. Loss of Test Board @ 25
C
869-894 MHz ~0.064dB
925-960 MHz ~0.068dB
1805-1880 MHz ~0.119dB
1930-1990 MHz ~0.126dB
2110-2170 MHz ~0.136dB
The loss estimates in the table above come from room temperature measurements. It is important to note that the loss
of the test board will change with temperature. This fact must be considered if the coupler is to be evaluated at other
temperatures.
(1.500)
(2.000)
.170
.120
.034 TYP
4X .063
Ø.015 Thru Hole
54147-0001
REV C
Available on Tape
and Reel for Pick and
Place Manufacturing.
USA/Canada:
Toll Free:
Europe
:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Model X3C19P1-04S
Rev D
Peak Power Handling
High-Pot testing of these couplers during the qualification procedure resulted in a minimum breakdown voltage of
0.56Kv (minimum recorded value). This voltage level corresponds to a breakdown resistance capable of handling at
least 12dB peaks over average power levels, for very short durations. The breakdown location consistently occurred
across the air interface at the coupler contact pads (see illustration below). The breakdown levels at these points will
be affected by any contamination in the gap area around these pads. These areas must be kept clean for optimum
performance. It is recommended that the user test for voltage breakdown under the maximum operating conditions and
over worst case modulation induced power peaking. This evaluation should also include extreme environmental
conditions (such as high humidity).
Orientation Marker
A printed circular feature appears on the top surface of the coupler to designate Pin 1. This orientation marker is not
intended to limit the use of the symmetry that these couplers exhibit but rather to facilitate consistent placement of these
parts into the tape and reel package. This ensures that the components are always delivered with the same orientation.
Refer to the table on page 2 of the data sheet for allowable pin configurations.
Test Plan
Xinger III couplers are manufactured in large panels and then separated. All parts are RF small signal tested and DC
tested for shorts/opens at room temperature in the fixture described above . (See “Qualification Flow Chart” section for
details on the accelerated life test procedures.)
USA/Canada:
Toll Free:
Europe:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Available on Tape and
Reel for Pick and Place
Manufacturing.
Model X3C19P1-04S
Rev D
Power Handling
The average power handling (total input power) of a Xinger coupler is a function of:
Internal circuit temperature.
Unit mounting interface temperature.
Unit thermal resistance
Power dissipated within the unit.
All thermal calculations are based on the following assumptions:
The unit has reached a steady state operating condition.
Maximum mounting interface temperature is 95
o
C.
Conduction Heat Transfer through the mounting interface.
No Convection Heat Transfer.
No Radiation Heat Transfer.
The material properties are constant over the operating temperature range.
Finite element simulations are made for each unit. The simulation results are used to calculate the unit thermal
resistance. The finite element simulation requires the following inputs:
Unit material stack-up.
Material properties.
Circuit geometry.
Mounting interface temperature.
Thermal load (dissipated power).
The classical definition for dissipated power is temperature delta (
T) divided by thermal resistance (R). The dissipated
power (P
dis
) can also be calculated as a function of the total input power (P
in
) and the thermal insertion loss (IL
therm
):
)(101
10
WP
R
T
P
therm
IL
indis
(1)
Power flow and nomenclature for an “X” style coupler is shown in Figure 1.
Available on Tape
and Reel for Pick and
Place Manufacturing.
USA/Canada:
Toll Free:
Europe
:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Model X3C19P1-04S
Rev D
Pin 1
Pin 4
Input Port
Coupled Port Direct Port
Isolated Port
P
In
P
Out
(RL) P
Out
(ISO)
P
Out
(CPL) P
Out
(DC)
Figure 1
The coupler is excited at the input port with P
in
(watts) of power. Assuming the coupler is not ideal, and that there are
no radiation losses, power will exit the coupler at all four ports. Symbolically written, P
out(RL)
is the power that is returned
to the source because of impedance mismatch, P
out(ISO)
is the power at the isolated port, P
out(CPL)
is the power at the
coupled port, and P
out(DC)
is the power at the direct port.
At Anaren, insertion loss is defined as the log of the input power divided by the sum of the power at the coupled and
direct ports:
Note: in this document, insertion loss is taken to be a positive number. In many places, insertion loss is written as a
negative number. Obviously, a mere sign change equates the two quantities.
)dB(
PP
P
log10IL
)DC(out)CPL(out
in
10
(2)
In terms of S-parameters, IL can be computed as follows:
)dB(SSlog10IL
2
41
2
3110
(3)
We notice that this insertion loss value includes the power lost because of return loss as well as power lost to the
isolated port.
For thermal calculations, we are only interested in the power lost “inside” the coupler. Since P
out(RL)
is lost in the source
termination and P
out(ISO)
is lost in an external termination, they are not be included in the insertion loss for thermal
calculations. Therefore, we define a new insertion loss value solely to be used for thermal calculations:
)(log10
)()()()(
10
dB
PPPP
P
IL
RLoutISOoutDCoutCPLout
in
therm
(4)
USA/Canada:
Toll Free:
Europe:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Available on Tape and
Reel for Pick and Place
Manufacturing.
Model X3C19P1-04S
Rev D
In terms of S-parameters, IL
therm
can be computed as follows:
)(log10
2
41
2
31
2
21
2
1110
dBSSSSIL
therm
(5)
The thermal resistance and power dissipated within the unit are then used to calculate the average total input power of
the unit. The average total steady state input power (P
in
) therefore is:
)(
101101
1010
W
R
T
P
P
thermtherm
ILIL
dis
in
(6)
Where the temperature delta is the circuit temperature (T
circ
) minus the mounting interface temperature (T
mnt
):
)( CTTT
o
mntcirc
(7)
The maximum allowable circuit temperature is defined by the properties of the materials used to construct the unit.
Multiple material combinations and bonding techniques are used within the Xinger III product family to optimize RF
performance. Consequently the maximum allowable circuit temperature varies. Please note that the circuit temperature
is not a function of the Xinger case (top surface) temperature. Therefore, the case temperature cannot be used as a
boundary condition for power handling calculations.
Due to the numerous board materials and mounting configurations used in specific customer configurations, it is the
end users responsibility to ensure that the Xinger III coupler mounting interface temperature is maintained within the
limits defined on
the power derating plots for the required average power handling. Additionally appropriate solder
composition is required to prevent
reflow or
fatigue failure at the RF ports. Finally, reliability is improved when the
mounting interface and RF port temperatures are kept to a minimum.
The power-derating curve illustrates how changes in the mounting interface temperature result in converse changes of
the power handling of the coupler.
Available on Tape
and Reel for Pick and
Place Manufacturing.
USA/Canada:
Toll Free:
Europe
:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Model X3C19P1-04S
Rev D
Mounting
In order for Xinger surface mount couplers to work
optimally, there must be 50Ω transmission lines leading to
and from all of the RF ports. Also, there must be a very
good ground plane underneath the part to ensure proper
electrical performance. If either of these two conditions is
not satisfied, electrical performance may not meet
published specifications.
Overall ground is improved if a dense population of plated
through holes connect the top and bottom ground layers
of the PCB. This minimizes ground inductance and
improves ground continuity. All of the Xinger hybrid and
directional couplers are constructed from ceramic filled
PTFE composites which possess excellent electrical and
mechanical stability having X and Y thermal coefficient of
expansion (CTE) of 17-25 ppm/
o
C.
When a surface mount hybrid coupler is mounted to a
printed circuit board, the primary concerns are; ensuring
the RF pads of the device are in contact with the circuit
trace of the PCB and insuring the ground plane of neither
the component nor the PCB is in contact with the RF
signal.
Mounting Footprint
Coupler Mounting Process
The process for assembling this component is a
conventional surface mount process as shown in
Figure 1. This process is conducive to both low and
high volume usage.
Figure 1: Surface Mounting Process Steps
Storage of Components: The Xinger III products
are available in either an immersion tin or tin-lead
finish. Commonly used storage procedures used to
control oxidation should be followed for these
surface mount components. The storage
temperatures should be held between 15
O
C and
60
O
C.
Substrate: Depending upon the particular
component, the circuit material has an x and y
coefficient of thermal expansion of between 17 and
25 ppm/°C. This coefficient minimizes solder joint
stresses due to similar expansion rates of most
commonly used board substrates such as RF35,
RO4003, FR4, polyimide and G-10 materials.
Mounting to “hard” substrates (alumina etc.) is
possible depending upon operational temperature
requirements. The solder surfaces of the coupler are
all copper plated with either an immersion tin or tin-
lead exterior finish.
Solder Paste: All conventional solder paste
formulations will work well with Anaren’s Xinger III
surface mount components. Solder paste can be
applied with stencils or syringe dispensers. An
example of a stenciled solder paste deposit is shown
in Figure 2. As shown in the figure solder paste is
applied to the four RF pads and the entire ground
plane underneath the body of the part.
.170
[4.32]
.120
[3.05]
4x .034
[0.86]
4x 50
Transmission
Line
To ensure proper electrical and thermal performance
there must be a ground plane with 100%
solder connection underneath the part orientated as
shown with text facing up.
RR
-04S
19P1
CC
X3C
Dimensions are in Inches [Millimeters]
X3C19P1-04S Mounting Footprint
USA/Canada:
Toll Free:
Europe:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Available on Tape and
Reel for Pick and Place
Manufacturing.
Model X3C19P1-04S
Rev D
Figure 2: Solder Paste Application
Coupler Positioning: The surface mount coupler can
be placed manually or with automatic pick and place
mechanisms. Couplers should be placed (see Figure 3
and 4) onto wet paste with common surface mount
techniques and parameters. Pick and place systems
must supply adequate vacuum to hold a 0.11 gram
coupler.
Figure 3: Component Placement
Figure 4: Mounting Features Example
Reflow: The surface mount coupler is conducive to most of
today’s conventional reflow methods. A low and high
temperature thermal reflow profile are shown in Figures 5
and 6, respectively. Manual soldering of these components
can be done with conventional surface mount non-contact
hot air soldering tools. Board pre-heating is highly
recommended for these selective hot air soldering methods.
Manual soldering with conventional irons should be avoided.
Available on Tape
and Reel for Pick and
Place Manufacturing.
USA/Canada:
Toll Free:
Europe
:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Model X3C19P1-04S
Rev D
Figure 5 – Low Temperature Solder Reflow Thermal Profile
Figure 6 – High Temperature Solder Reflow Thermal Profile
USA/Canada:
Toll Free:
Europe:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Available on Tape and
Reel for Pick and Place
Manufacturing.
Model X3C19P1-04S
Rev D
Qualification Flow Chart
Visual Inspection
n=45
Mechanical Inspection
n=40
Solderability Test
n=5
Initial RF Test
n=40
Solder Units to Test Board
n=20
Post Solder Visual Inspection
n=20
Initial RF Test Board Mounted
Over Temp
n=20
Visual Inspection
n=40
Automated TT&R Operation
n=45
Thermal Shock
n=40
Post Shock RF Test
n=40
Moisture Resistance
n=40
Reflow /Resistance to
Solder Heat
n=20 (loose)
Bake Units
n=40
Micro section
n = 2
Visual Inspection
n=40
Life Test
n=3
Final RF Test
n=3
RF Test
n = 20 (loose), n = 20
(mounted over temp)
Voltage Breakdown
n=10
Visual Inspection
n=10
RF Test
n=10
Micro section
n = 1 loose control, n = 1
mounted control, n = 3
board mounted, n = 3
loose
Visual Inspection
n=45
Available on Tape
and Reel for Pick and
Place Manufacturing.
USA/Canada:
Toll Free:
Europe
:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Model X3C19P1-04S
Rev D
Application Information
The X3C19P1-04S is an “X” style 4dB coupler. Port configurations are defined in the table on page 2 of this data sheet
and an example driving port 1 is shown below. The change was made to allow better placement of the termination resistors
when the coupler is used in a serial splitter/combiner network.
Ideal Coupler Operation
The primary application for 4dB couplers is in serial splitting and combining networks. These networks are often employed
when the combining of 3 amplifiers is required. Unlike corporate networks, serial networks are not limited to binary
divisions (corporate networks are limited to 2 n number of splits, where n is an integer). Serial networks can be designed
with [3, 4, 5, ..., n] splits, but have a practical limitation of about 8 splits.
2-Way Splitter for Doherty Power Amplifer
Hybrid coupler can be used in Doherty power amplifier to split the input power into the desired power ratio and phase
delay. In above symmetrical Doherty power amplifier (main and peaking amplifier delivers equal amount output power at
max drive condition), 3dB hybrid splits the input power into 1:1 ratio with 90 degree phase difference.
When the peaking amplifier is off, or when peaking amplifier is dramatically different than main amplifier due to bias,
matching, difference between transistors, the 3dB hybrid coupler does not see equally unmatched termination, the
mismatch is then reflected not only to isolated port, but also shows up at input port as return loss mismatch.
4dB hybrid splits the input power into 1:15 ratio with 90 degree phase difference. It can be used in asymmetrical (1:1.5)
Doherty power amplifier architecture as splitter. The 4dB hybrid is also used in some symmetrical Doherty power amplifier
to compensate the gain difference between main and peaking amplifiers. It is worth noting that 3dB and 4dB hybrid react
differently to the termination mismatch, resulting in different return loss at input port.
4
3
0.631V
(-4dB)
1
Isolated port 2
1V
0.776V
(-2.2dB)
Main
Amplifier
°
°
Peaking
Amplifier
°
°
50
90°
35
90°
Input
3dB/4dB/5dB
Hybrid Coupler
Output
USA/Canada:
Toll Free:
Europe:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Available on Tape and
Reel for Pick and Place
Manufacturing.
Model X3C19P1-04S
Rev D
Packaging and Ordering Information
Parts are available in reels. Packaging follows EIA 481-2 for reels. Parts are oriented in tape and reel as shown below.
Minimum order quantities are 2000 per reel.
Direction Of
Part Feed
(Unloading)
.079
[2.00]
.157
[4.00]
.069
[1.75]
.217
[5.50] .472
[12.00]
.315
[8.00]
TYP Ø.059
[Ø1.50]
.264
[6.70]
.217
[5.50]
.012
[0.30]
.079
[2.00]
Dimensions are in Inches [Millimeters]
CC
RR
NO
MODEL
B
ØA ØC
REEL DIMENSIONS (inches [mm])
TABLE 1
ØA 13.0 [330.0]
B .945 [24.0]
ØC 4.017 [102.03]
ØD 0.512 [13.0]
Available on Tape
and Reel for Pick and
Place Manufacturing.
USA/Canada:
Toll Free:
Europe
:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Model X3C19P1-04S
Rev D
