MAX4130–MAX4134
________________________________________________________________ Maxim Integrated Products 1
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
General Description
The MAX4130–MAX4134 family of operational amplifiers
combines 10MHz gain-bandwidth product and excellent
DC accuracy with Rail-to-Rail®operation at the inputs
and outputs. These devices require only 900µA per
amplifier, and operate from either a single supply (+2.7V
to +6.5V) or dual supplies (±1.35V to ±3.25V) with a
common-mode voltage range that extends 250mV
beyond VEE and VCC. They are capable of driving 250Ω
loads and are unity-gain stable. In addition, the
MAX4131/ MAX4133 feature a shutdown mode in which
the outputs are placed in a high-impedance state and
the supply current is reduced to only 25µA per amplifier.
With their rail-to-rail input common-mode range and
output swing, the MAX4130–MAX4134 are ideal for low-
voltage, single-supply operation. Although the minimum
operating voltage is specified at 2.7V, the devices
typically operate down to 1.8V. In addition, low offset
voltage and high speed make them the ideal signal-
conditioning stages for precision, low-voltage data-
acquisition systems. The MAX4130 is offered in the
space-saving 5-pin SOT23 package. The MAX4131 is
offered in the ultra-small 6-bump, 1mm x 1.5mm chip-
scale package (UCSP™).
________________________Applications
Battery-Powered Instruments
Portable Equipment
Data-Acquisition Systems
Signal Conditioning
Low-Power, Low-Voltage Applications
Features
♦6-Bump UCSP (MAX4131)
♦+2.7V to +6.5V Single-Supply Operation
♦Rail-to-Rail Input Common-Mode Voltage Range
♦Rail-to-Rail Output Voltage Swing
♦10MHz Gain-Bandwidth Product
♦900µA Quiescent Current per Amplifier
♦25µA Shutdown Function (MAX4131/MAX4133)
♦200µV Offset Voltage
♦No Phase Reversal for Overdriven Inputs
♦Drive 250ΩLoads
♦Stable with 160pF Capacitive Loads
♦Unity-Gain Stable
Single/Dual/Quad, Wide-Bandwidth, Low-Power,
Single-Supply, Rail-to-Rail I/O Op Amps
MAX147
MAX4131
SHDN
31
2
4
5
6
8
7
VDD
+3V
AIN
VREF
GND
DOUT
SERIAL
INTERFACE SCLK
CS
Typical Operating Circuit
19-1089; Rev 3; 3/03
Ordering Information
*Dice are specified at TA= +25°C. DC parameters only.
Ordering Information continued at end of data sheet.
Selector Guide
Pin Configurations appear at end of data sheet.
Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd.
UCSP is a trademark of Maxim Integrated Products, Inc.
PART AMPS PER
PACKAGE
SHUTDOWN
MODE
PIN-
PACKAGE
MAX4130 1 —5 SOT23
MAX4131 1 Yes 6 UCSP,
8 µMAX/SO
MAX4132 2 —8 µMAX/SO
MAX4133 2 Yes 14 SO
MAX4134 4 —14 SO
PART TEMP RANGE PIN-
PACKAGE
TOP
MARK
MAX4130EUK-T -40°C to +85°C 5 SOT23-5 AABB
MAX4131C/D 0°C to +70°C Dice* —
MAX4131EBT-T -40°C to +85°C 6 UCSP-6 AAX
MAX4131EUA -40°C to +85°C 8 µMAX —
MAX4131ESA -40°C to +85°C 8 SO —
MAX4130–MAX4134
Single/Dual/Quad, Wide-Bandwidth, Low-Power,
Single-Supply Rail-to-Rail I/O Op Amps
2 _______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
DC ELECTRICAL CHARACTERISTICS
(VCC = +2.7V to +6.5V, VEE = 0V, VCM = 0V, VOUT = VCC/2, RLtied to VCC/2, SHDN ≥2V (or open), TA= +25°C, unless
otherwise noted.)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Supply Voltage (VCC - VEE)...................................................7.5V
IN+, IN-, SHDN Voltage ...................(VCC + 0.3V) to (VEE - 0.3V)
Output Short-Circuit Duration (Note 1).......................Continuous
(short to either supply)
Continuous Power Dissipation (TA= +70°C)
5-Pin SOT23 (derate 7.1mW/°C above +70°C)............571mW
6-Bump UCSP (derate 2.9mW/°C above +70°C).........308mW
8-Pin SO (derate 5.88mW/°C above +70°C)................471mW
8-Pin µMAX (derate 4.10mW/°C above +70°C) ...........330mW
14-Pin SO (derate 8.00mW/°C above +70°C)..............640mW
Operating Temperature Range
MAX413_E__ ...................................................-40°C to +85°C
Maximum Junction Temperature .....................................+150°C
Storage Temperature Range .............................-65°C to +160°C
Lead Temperature (soldering, 10s) .................................+300°C
Bump Reflow Temperature .........................................+235°C
Note 1: Provided that the maximum package power-dissipation rating is not exceeded.
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
MAX4130EUK ±0.35 ±1.50
MAX4131ESA ±0.20 ±0.60
MAX4131EUA/
MAX4131EBT ±0.35 ±1.20
MAX4132ESA/
MAX4133ESD ±0.25 ±0.75
MAX4132EUA ±0.40 ±1.50
Input Offset Voltage VOS VCM = VEE to VCC
MAX4134ESD ±0.35 ±1.50
mV
Input Bias Current IBVCM = VEE to VCC ±50 ±150 nA
MAX4131EBT ±15
Input Offset Current IOS VCM = VEE to VCC All other packages ±12 nA
Differential Input Voltage RIN -1.5V < VDIFF < 1.5V 500 kΩ
Common-Mode Input Voltage
Range CMVR VEE -
0.25
VCC -
0.25 V
MAX4130EUK 67 90
MAX4131ESA 78 98
MAX4131EUA/
MAX4131EBT 68 88
MAX4132ESA/
MAX4133ESD 74 94
MAX4132EUA 66 86
Common-Mode Rejection Ratio CMRR VEE - 0.25V < VCM
< VCC + 0.25V
MAX4134ESD 64 84
dB
Power-Supply Rejection Ratio PSRR VCC = 2.7V to 6.5V 78 100 dB
Output Resistance ROUT AV = 1 0.1 Ω
Off-Leakage Current ILKG SHDN < 0.8V, VOUT = 0V to VCC ±0.1 ±1 µA
MAX4130–MAX4134
Single/Dual/Quad, Wide-Bandwidth, Low-Power,
Single-Supply Rail-to-Rail I/O Op Amps
_______________________________________________________________________________________ 3
DC ELECTRICAL CHARACTERISTICS (continued)
(VCC = +2.7V to +6.5V, VEE = 0V, VCM = 0V, VOUT = VCC/2, RLtied to VCC/2, SHDN ≥2V (or open), TA= +25°C, unless
otherwise noted.)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
VOUT = 0.25V to 2.45V,
RL = 100kΩ92 108
VCC = 2.7V
VOUT = 0.4V to 2.3V,
RL = 250Ω72 82
VOUT = 0.25V to 4.75V,
RL = 100kΩ94 108
Large-Signal Voltage Gain AV
VCC = 5V
VOUT = 0.4V to 4.6V,
RL = 250Ω75 86
dB
VCC - VOH 12 20
RL = 100kΩVOL - VEE 20 35
VCC - VOH 240 290
MAX4130/
MAX4131
RL = 250ΩVOL - VEE 125 170
VCC - VOH 15 30
RL = 100kΩVOL - VEE 25 40
VCC - VOH 280 330
Output Voltage Swing VO
MAX4132/
MAX4133/
MAX4134 RL = 250ΩVOL - VEE 180 230
mV
Output Short-Circuit Current ISC 50 mA
VIL Low 0.8
SHDN Logic Threshold VIH
MAX4131–MAX4134 High 2.0 V
SHDN Input Current IIL MAX4131–MAX4134 ±1 ±3 µA
Operating Supply Voltage
Range VCC 2.7 6.5 V
VCC = 2.7V 900 1050
Supply Current per Amplifier ICC VCM = VOUT = VCC/2 VCC = 5V 1000 1150 µA
VCC = 2.7V 25 40
Shutdown Supply Current per
Amplifier ISHDN SHDN > 0.8V, MAX4131–
MAX4134 VCC = 5V 40 60
µA
DC ELECTRICAL CHARACTERISTICS
(VCC = +2.7V to +6.5V, VEE = 0V, VCM = 0V, VOUT = VCC/2, RLtied to VCC/2, SHDN ≥2V (or open), TA= -40°C to +85°C, unless
otherwise noted.) (Note 2)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
MAX4130EUK ±3.50
MAX4131ESA ±0.75
MAX4131EUA/MAX4131EBT ±4.40
MAX4132ESA/MAX4133ESD ±0.95
MAX4132EUA ±4.70
Input Offset Voltage VOS VCM = VEE to
VCC
MAX4134ESD ±4.00
mV
Input Offset Voltage Tempco TCVOS ±2 µV/°C
Input Bias Current IBVCM = VEE to VCC ±160 nA
MAX4130–MAX4134
Single/Dual/Quad, Wide-Bandwidth, Low-Power,
Single-Supply Rail-to-Rail I/O Op Amps
4 _______________________________________________________________________________________
DC ELECTRICAL CHARACTERISTICS
(VCC = +2.7V to +6.5V, VEE = 0V, VCM = 0V, VOUT = VCC/2, RLtied to VCC/2, SHDN ≥2V (or open), TA= -40°C to +85°C, unless
otherwise noted.) (Note 2)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
MAX4131EBT ±24
Input Offset Current IOS VCM = VEE to VCC All other packages ±18 nA
Common-Mode Input Voltage
Range CMVR VEE -
0.20
VCC -
0.20 V
MAX4130EUK 62
MAX4131ESA 76
MAX4131EUA/MAX4131EBT 60
MAX4132ESA/MAX4133ESD 74
MAX4132EUA 58
Common-Mode Rejection Ratio CMRR
VEE - 0.2V
< VCM < VCC
+ 0.2V
MAX4134ESD 60
dB
Power-Supply Rejection Ratio PSRR VCC = 2.7V to 6.5V 74 dB
Off-Leakage Current ILKG SHDN < 0.8V, VOUT = 0V to VCC ±12 µA
VOUT = 0.25V to 2.45V,
RL = 100kΩ84
VCC = 2.7V
VOUT = 0.4V to 2.3V,
RL = 250Ω66
VOUT = 0.25V to 4.75V,
RL = 100kΩ86
Large-Signal Voltage Gain AV
VCC = 5V
VOUT = 0.4V to 4.6V,
RL = 250Ω68
dB
VCC - VOH 25
RL = 100kΩVOL - VEE 40
VCC - VOH 300
MAX4130/
MAX4131ESA/
MAX4131EUA RL = 250ΩVOL - VEE 190
VCC - VOH 25
RL = 100kΩVOL - VEE 40
VCC - VOH 350
MAX4131EBT
RL = 250ΩVOL - VEE 190
VCC - VOH 35
RL = 100kΩVOL - VEE 50
VCC - VOH 350
Output Voltage Swing VO
MAX4132/
MAX4133/
MAX4134 RL = 250ΩVOL - VEE 250
mV
MAX4130–MAX4134
Single/Dual/Quad, Wide-Bandwidth, Low-Power,
Single-Supply Rail-to-Rail I/O Op Amps
_______________________________________________________________________________________ 5
DC ELECTRICAL CHARACTERISTICS (continued)
(VCC = +2.7V to +6.5V, VEE = 0V, VCM = 0V, VOUT = VCC/2, RLtied to VCC/2, SHDN ≥2V (or open), TA= -40°C to +85°C, unless
otherwise noted.) (Note 2)
AC ELECTRICAL CHARACTERISTICS
(VCC = +2.7V to +6.5V, VEE = 0V, SHDN ≥2V (or open), TA= +25°C, unless otherwise noted.)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
VIL Low 0.8
SHDN Logic Threshold VIH
MAX4131–MAX4134 High 2.0 V
SHDN Input Current IIL MAX4131–MAX4134 ±3 µA
Operating Supply Voltage Range VCC 2.7 6.5 V
VCC = 2.7V 1200
MAX4131EBT VCC = 5V 1350
VCC = 2.7V 1100
Supply Current per Amplifier ICC VCM = VOUT =
VCC/2 All other
devices VCC = 5V 1200
µA
VCC = 2.7V 50
Shutdown Supply Current per
Amplifier ISHDN
SHDN > 0.8V,
MAX4131–MAX4134 VCC = 5V 70 µA
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Gain-Bandwidth Product GBWP 10 MHz
Phase Margin θM62 Degrees
Gain Margin GM12 dB
Total Harmonic Distortion THD f = 10kHz, VOUT = 2VP-P (AV = 1) 0.003 %
Slew Rate SR 4 V/µs
Settling Time to 0.01% tSAV = 1, VOUT = 2V step 2.0 µs
Turn-On Time tON VCC = 0V to 3V step, VOUT = VCC/2 1 µs
Enable 1
SHDN Delay MAX4131–MAX4134,
VCC = 3V, VOUT = VCC/2 Disable 0.2 µs
Input Capacitance CIN 3pF
Input Noise-Voltage Density enf = 1kHz 22 nV/√Hz
Input Noise-Current Density inf = 1kHz 0.4 pA/√Hz
Capacitive-Load Stability CLAV = 1 160 pF
Note 2: All devices are 100% tested at TA= +25°C. MAX4130EUK/MAX4131EBT temperature limits are guaranteed by design.
MAX4130–MAX4134
Single/Dual/Quad, Wide-Bandwidth, Low-Power,
Single-Supply, Rail-to-Rail I/O Op Amps
6 _______________________________________________________________________________________
60
-40
100 1k 10k 1M 10M100k 100M
GAIN AND PHASE
vs. FREQUENCY
-20
FREQUENCY (Hz)
GAIN (dB)
0
20
40
PHASE
GAIN
AV = +1000
NO LOAD
PHASE (DEGREES)
180
144
72
0
-72
-144
-180
-108
-36
36
108
MAX4130/34-01 60
-40
100 1k 10k 1M 10M100k 100M
GAIN AND PHASE
vs. FREQUENCY (WITH CLOAD)
-20
MAX4130/34-02
FREQUENCY (Hz)
GAIN (dB)
0
20
40
PHASE
GAIN
AV = +1000
RL = ∞
CL = 160pF
PHASE (DEGREES)
180
144
72
0
-72
-144
-180
-108
-36
36
108
0
-100
10 100 1k 100k 1M 10M10k 100M
POWER-SUPPLY REJECTION
vs. FREQUENCY
-80
MAX4130/34-03
FREQUENCY (Hz)
PSR (dB)
-60
-40
-20
AV = +1
0
10
5
15
20
25
35
30
45
40
50
-40-25-105 20355065 8095
SHUTDOWN SUPPLY CURRENT
vs. TEMPERATURE
MAX4130/34-07
TEMPERATURE (°C)
SUPPLY CURRENT (µA)
VCC = +6.5V
VCC = +2.7V
100
0.10
0.01
100 1k 100k 1M 10M
10k 100M
OUTPUT IMPEDANCE
vs. FREQUENCY
MAX4130/34-05
FREQUENCY (Hz)
OUTPUT IMPEDANCE (Ω)
1
10
AV = +1
1150
800
850
900
950
1050
1000
1100
-40 -25 -10 5 20 35 50 65 80 95
SUPPLY CURRENT PER AMPLIFIER
vs. TEMPERATURE
MAX4130/34-06
TEMPERATURE (°C)
SUPPLY CURRENT (µA)
VCC = +6.5V
VCC = +2.7V
-10
-5
0
5
10
15
20
-40 -25 -10 5 20 35 50 65 80 95
OUTPUT LEAKAGE CURRENT
vs. TEMPERATURE
MAX4130/34-08
TEMPERATURE (°C)
LEAKAGE CURRENT (µA)
VCC = +6.5V
VOUT SHORT
TO VCC VCC = +2.7V
VCC = +6.5V
VOUT SHORT
TO VEE VCC = +2.7V
AV = +1
SHDN = 0V
Typical Operating Characteristics
(VCC = +5V, VEE = 0V, VCM = VCC / 2, TA = +25°C, unless otherwise noted.)
-60
0123456
INPUT BIAS CURRENT
vs. COMMON-MODE VOLTAGE
MAX4130/34-10
COMMON-MODE VOLTAGE (V)
INPUT BIAS CURRENT (nA)
-50
-40
-30
-20
-10
0
10
20
30
40
VCC = +2.7V
VCC = +6.5V
-60
-40
-40 -25 -10 5 20 35 50 65 80 95
INPUT BIAS CURRENT
vs. TEMPERATURE
MAX4130/34-11
TEMPERATURE (°C)
INPUT BIAS CURRENT (nA)
-20
0
20
40
60
VCC = +6.5V, VCM = VCC
VCC = +2.7V, VCM = VEE
VCC = +2.7V, VCM = VCC
VCC = +6.5V, VCM = VEE
MAX4130–MAX4134
Single/Dual/Quad, Wide-Bandwidth, Low-Power,
Single-Supply, Rail-to-Rail I/O Op Amps
_______________________________________________________________________________________ 7
120
70
75
0 600
110
115
OUTPUT VOLTAGE: EITHER SUPPLY (mV)
GAIN (dB)
300
95
85
90
80
100 200 500
105
100
400
MAX4130/34-19
LARGE-SIGNAL GAIN
vs. OUTPUT VOLTAGE
RL = 500Ω
RL = 100kΩ
RL = 10kΩ
RL = 2kΩ
VCC = +6.5V
RL TO VCC
130
-40 -25 -10 5 20 35 50 65 80 95
LARGE-SIGNAL GAIN
vs. TEMPERATURE
90
120
MAX4130/34-20
TEMPERATURE (°C)
GAIN
(dB)
110
100
85
95
125
115
105
VCC = +6.5V, RL TO VCC OR VEE
VCC = +2.7V, RL TO VCC OR VEE
RL = 100kΩ
VOUT(P-P) = VCC - 0.6V
1.2
1.3
1.5
1.4
1.6
1.7
1.8
1.9
-40 -25 -10 5 20 35 50 65 80 95
MINIMUM OPERATING VOLTAGE
vs. TEMPERATURE
MAX4130/34-21
TEMPERATURE (°C)
MINIMUM OPERATING VOLTAGE (V)
Typical Operating Characteristics (continued)
(VCC = +5V, VEE = 0V, VCM = VCC / 2, TA = +25°C, unless otherwise noted.)
120
80
85
90
95
100
105
110
115
-40 -25 -10 5 20 35 50 65 80 95
COMMON-MODE REJECTION
vs. TEMPERATURE
MAX4130/34-12
TEMPERATURE (°C)
COMMON-MODE REJECTION (dB)
VCM = 0V TO 5.0V
VCM = 0.2V TO 5.2V
VCM = 0.3V TO 5.3V
130
70
0 600
120
OUTPUT VOLTAGE: EITHER SUPPLY (mV)
GAIN (dB)
300
100
90
80
100 200 500
110
400
MAX4130/34-16
LARGE-SIGNAL GAIN
vs. OUTPUT VOLTAGE
VCC = +6.5V
RL TO VEE
RL = 500Ω
RL = 100kΩ
RL = 10kΩ
RL = 2kΩ
120
60
0 600
110
OUTPUT VOLTAGE: EITHER SUPPLY (mV)
GAIN (dB)
300
90
80
70
100 200 500
100
400
MAX4130/34-15
LARGE-SIGNAL GAIN
vs. OUTPUT VOLTAGE
VCC = +2.7V
RL TO VEE
RL = 500Ω
RL = 100kΩ
RL = 10kΩ
RL = 2kΩ
120
80
-40 -25 -10 5 20 35 50 65 80 95
LARGE-SIGNAL GAIN
vs. TEMPERATURE
90
MAX4130/34-17
TEMPERATURE (°C)
GAIN (dB)
105
85
95
115
110
100 VCC = +2.7V,
RL TO VEE
VCC = +6.5V,
RL TO VCC
VCC = +2.7V, RL TO VCC
VOUT(P-P) = VCC -1V
RL = 500Ω
VCC = +6.5V,
RL TO VEE
120
70
75
0 600
110
115
OUTPUT VOLTAGE: EITHER SUPPLY (mV)
GAIN (dB)
300
95
85
90
80
100 200 500
105
100
400
MAX4130/34-18
LARGE-SIGNAL GAIN
vs. OUTPUT VOLTAGE
RL = 500Ω
RL = 100kΩ
RL = 10kΩ
RL = 2kΩ
VCC = +2.7V
RL TO VCC
-3.00
-2.25
-0.75
-1.50
0
1.50
0.75
2.25
3.00
-40 -25 -10 5 20 35 50 65 80 95
INPUT OFFSET VOLTAGE
vs. TEMPERATURE
MAX4130/34-09
TEMPERATURE (°C)
VOLTAGE (mV)
SOT23
PACKAGE
SO PACKAGE
MAX4130–MAX4134
Single/Dual/Quad, Wide-Bandwidth, Low-Power,
Single-Supply, Rail-to-Rail I/O Op Amps
8 _______________________________________________________________________________________
140
80
10k1k 100k 10M1M
CHANNEL SEPARATION
vs. FREQUENCY
MAX4130/34-25a
FREQUENCY (Hz)
CHANNEL SEPARATION (dB)
100
90
130
110
120
VS = +5V
10 100k10k
FREQUENCY (Hz)
100 1k
0.030
0
0.005
0.010
0.015
0.020
0.025
TOTAL HARMONIC DISTORTION
AND NOISE vs. FREQUENCY
MAX4130/34-22A
THD AND NOISE (%)
2Vp-p SIGNAL
500kHz LOWPASS FILTER
RL = 10kΩ TO VCC / 2
0.1
0.001
4.0 4.44.2 5.04.84.6
TOTAL HARMONIC DISTORTION AND NOISE
vs. PEAK-TO-PEAK SIGNAL AMPLITUDE
MAX4130/34-23
PEAK-TO-PEAK SIGNAL AMPLITUDE (V)
THD + NOISE (%)
0.01
RL = 100kΩ
RL = 10kΩ
RL = 2kΩ
RL = 250Ω
AV = +1
10kHz SINE WAVE
RL TO VCC / 2
500kHz LOWPASS FILTER IN
TIME (200ns/div)
VOLTAGE (50mV/div)
OUT
MAX4131
SMALL-SIGNAL TRANSIENT
RESPONSE (NONINVERTING)
MAX4130/34-24
AV = +1
IN
TIME (200ns/div)
VOLTAGE (50mV/div)
OUT
MAX4131
SMALL-SIGNAL TRANSIENT
RESPONSE (INVERTING)
MAX4130/34-25
AV = -1
IN
TIME (2µs/div)
VOLTAGE (2V/div)
OUT
MAX4131
LARGE-SIGNAL TRANSIENT
RESPONSE (NONINVERTING)
MAX4130/34-26
AV = +1
IN
TIME (2µs/div)
VOLTAGE (2V/div)
OUT
MAX4131
LARGE-SIGNAL TRANSIENT
RESPONSE (INVERTING)
MAX4130/34-27
AV = -1
Typical Operating Characteristics (continued)
(VCC = +5V, VEE = 0V, VCM = VCC / 2, TA = +25°C, unless otherwise noted.)
160
0
-40 -25 -10 5 20 35 50 65 80 95
MINIMUM OUTPUT VOLTAGE
vs. TEMPERATURE
20
140
120
MAX4130/34-13
TEMPERATURE (°C)
VOUT - VEE (mV)
100
80
60
40
RL TO VCC
VCC = +6.5V, RL = 500Ω
VCC = +2.7V, RL = 100kΩ
VCC = +2.7V, RL = 500Ω
VCC = +6.5V, RL = 100kΩ
0
50
100
150
200
250
300
-40 -25 -10 5 20 35 50 65 80 95
MAXIMUM OUTPUT VOLTAGE
vs. TEMPERATURE
MAX4130/34-14
TEMPERATURE (°C)
VCC - VOUT (mV)
RL TO VEE VCC = +6.5V, RL = 500Ω
VCC = +2.7V, RL = 100kΩ (BOTTOM)
VCC = +2.7V, RL = 500Ω
VCC = +6.5V, RL = 100kΩ (TOP)
MAX4130–MAX4134
Single/Dual/Quad, Wide-Bandwidth, Low-Power,
Single-Supply, Rail-to-Rail I/O Op Amps
_______________________________________________________________________________________ 9
Pin Description
R3
R3 = R1 R2
R1 R2
MAX4130
MAX4131
MAX4132
MAX4133
MAX4134
Figure 1a. Reducing Offset Error Due to Bias Current
(Noninverting)
R3
R3 = R1 R2
R1 R2
MAX4130
MAX4131
MAX4132
MAX4133
MAX4134
Figure 1b. Reducing Offset Error Due to Bias Current
(Inverting)
PIN
MAX4131
MAX4130 SO/µMAX UCSP MAX4132 MAX4133 MAX4134 NAME FUNCTION
16 A2———OUT Output
2 4 A1 4 4 11 VEE Negative Supply. Connect to
GND for single-supply operation.
33 B1———IN+ Noninverting Input
42 B2———IN- Inverting Input
5 7 A3 8 14 4 VCC Positive Supply
—1, 5 ——5, 7, 8, 10 —N.C. No Connection. Not internally
connected.
—8B3——SHDN
Shutdown Control. Connect to
VCC or leave floating to enable
amplifier.
—— — 1, 7 1, 13 1, 7 OUT1, OUT2 Outputs for Amps 1 and 2
—— — 2, 6 2, 12 2, 6 IN1-, IN2- Inverting Inputs for Amps 1 and 2
—— — 3, 5 3, 11 3, 5 IN1+, IN2+ Noninverting Inputs for Amps 1
and 2
————6, 9 —SHDN1,
SHDN2
Shutdown Control. Provides
independent shutdown control for
amps 1 and 2. Connect to VCC or
leave floating to enable
amplifiers.
—————8, 14 OUT3,
OUT4 Outputs for Amps 3 and 4
—————9, 13 IN3-, IN4- Inverting Inputs for Amps 3 and 4
—————10, 12 IN3+, IN4+ Noninverting Inputs for Amps 3
and 4
MAX4130–MAX4134
Single/Dual/Quad, Wide-Bandwidth, Low-Power,
Single-Supply, Rail-to-Rail I/O Op Amps
10 ______________________________________________________________________________________
Applications Information
Rail-to-Rail Input Stage
Devices in the MAX4130–MAX4134 family of high-
speed amplifiers have rail-to-rail input and output
stages designed for low-voltage, single-supply opera-
tion. The input stage consists of separate NPN and
PNP differential stages that combine to provide an
input common-mode range that extends 0.2V beyond
the supply rails. The PNP stage is active for input volt-
ages close to the negative rail, and the NPN stage is
active for input voltages near the positive rail. The input
offset voltage is typically below 200µV. The switchover
transition region, which occurs near VCC / 2, has been
extended to minimize the slight degradation in com-
mon-mode rejection ratio caused by the mismatch of
the input pairs. Their low offset voltage, high band-
width, and rail-to-rail common-mode range make these
op amps excellent choices for precision, low-voltage
data-acquisition systems.
Since the input stage switches between the NPN and
PNP pairs, the input bias current changes polarity as
the input voltage passes through the transition region.
Reduce the offset error caused by input bias currents
flowing through external source impedances by match-
ing the effective impedance seen by each input
(Figures 1a, 1b). High source impedances, together
with input capacitance, can create a parasitic pole that
produces an underdamped signal response. Reducing
the input impedance or placing a small (2pF to 10pF)
capacitor across the feedback resistor improves
response.
The MAX4130–MAX4134s’ inputs are protected from
large differential input voltages by 1kΩseries resistors
and back-to-back triple diodes across the inputs
(Figure 2). For differential input voltages less than 1.8V,
input resistance is typically 500kΩ. For differential input
voltages greater than 1.8V, input resistance is approxi-
mately 2kΩ. The input bias current is given by the fol-
lowing equation:
I = V - 1.8V
2k
BIAS DIFF
Ω
1kΩ
1kΩ
Figure 2. Input Protection Circuit
MAX4130–MAX4134
Single/Dual/Quad, Wide-Bandwidth, Low-Power,
Single-Supply, Rail-to-Rail I/O Op Amps
______________________________________________________________________________________ 11
Rail-to-Rail Output Stage
The minimum output voltage is within millivolts of
ground for single-supply operation where the load is
referenced to ground (VEE). Figure 3 shows the input
voltage range and output voltage swing of a MAX4131
connected as a voltage follower. With a +3V supply
and the load tied to ground, the output swings from
0.00V to 2.90V. The maximum output voltage swing
depends on the load, but will be within 150mV of a +3V
supply, even with the maximum load (500Ωto ground).
Driving a capacitive load can cause instability in most
high-speed op amps, especially those with low quies-
cent current. The MAX4130–MAX4134 have a high tol-
erance for capacitive loads. They are stable with
capacitive loads up to 160pF. Figure 4 gives the stable
operating region for capacitive loads. Figures 5 and 6
show the response with capacitive loads and the
results of adding an isolation resistor in series with the
output (Figure 7). The resistor improves the circuit’s
phase margin by isolating the load capacitor from the
op amp’s output.
IN
TIME (1µs/div)
VOLTAGE (1V/div)
OUT
VCC = 3V, RL = 10kΩ to VEE
Figure 3. Rail-to-Rail Input/Output Voltage Range
500
0
50
100
150
200
300
350
400
450
0.1 1 10010
LOAD RESISTANCE (kΩ)
LOAD CAPACITANCE (pF)
250
UNSTABLE
OPERATING
REGION
STABLE
OPERATING
REGION
RL TO VEE
VOUT = VCC/2
Figure 4. Capacitive-Load Stability
IN
TIME (200ns/div)
VOLTAGE (50mV/div)
OUT
VCC = 5V
RL = 10kΩ
CL = 130pF
Figure 5. MAX4131 Small-Signal Transient Response with
Capacitive Load
Figure 6. MAX4131 Transient Response to Capacitive Load
with Isolation Resistor
IN
TIME (500ns/div)
VOLTAGE (50mV/div)
OUT
VCC = 5V
CL = 1000pF
RS = 39Ω
MAX4130–MAX4134
Single/Dual/Quad, Wide-Bandwidth, Low-Power,
Single-Supply, Rail-to-Rail I/O Op Amps
12 ______________________________________________________________________________________
Power-Up and Shutdown Mode
The MAX4130–MAX4134 amplifiers typically settle with-
in 1µs after power-up. Figures 9 and 10 show the out-
put voltage and supply current on power-up, using the
test circuit of Figure 8.
The MAX4131 and MAX4133 have a shutdown option.
When the shutdown pin (SHDN) is pulled low, the sup-
ply current drops below 25µA per amplifier and the
amplifiers are disabled with the outputs in a high-
impedance state. Pulling SHDN high or leaving it float-
ing enables the amplifier. In the dual-amplifier
MAX4133, the shutdown functions operate indepen-
dently. Figures 11 and 12 show the output voltage and
supply current responses of the MAX4131 to a shut-
down pulse, using the test circuit of Figure 8.
RS
CL
Figure 7. Capacitive-Load Driving Circuit
SHDN
OUT
0V TO 2.7V
STEP FOR
SHUTDOWN
TEST
0V TO 2.7V STEP
FOR POWER-UP
TEST; 2.7V FOR
SHUTDOWN
ENABLE TEST
SUPPLY-CURRENT
MONITORING POINT
VCC
*0.1µF
10Ω
2kΩ
*FOR SHUTDOWN TEST ONLY.
10kΩ
2kΩ
Figure 8. Power-Up/Shutdown Test Circuit
VCC
TIME (5µs/div)
VOLTAGE (1V/div)
OUT
Figure 9. Power-Up Output Voltage
VCC
(1V/div)
TIME (5µs/div)
IEE
(500µA/div)
Figure 10. Power-Up Supply Current
MAX4130–MAX4134
Single/Dual/Quad, Wide-Bandwidth, Low-Power,
Single-Supply, Rail-to-Rail I/O Op Amps
______________________________________________________________________________________ 13
Power Supplies and Layout
The MAX4130–MAX4134 operate from a single +2.7V
to +6.5V power supply, or from dual supplies of ±1.35V
to ±3.25V. For single-supply operation, bypass the
power supply with a 0.1µF ceramic capacitor in parallel
with at least 1µF. For dual supplies, bypass each sup-
ply to ground.
Good layout improves performance by decreasing the
amount of stray capacitance at the op amp’s inputs
and outputs. Decrease stray capacitance by placing
external components close to the op amp’s pins, mini-
mizing trace lengths and resistor leads.
UCSP Applications Information
For the latest application details on UCSP construction,
dimensions, tape carrier information, PC board tech-
niques, bump-pad layout, and the recommended
reflow temperature profile, as well as the latest informa-
tion on reliability testing results, go to Maxim’s website
at www.maxim-ic.com/ucsp and search for the
Application Note: UCSP–A Wafer-Level Chip-Scale
Package.
SHDN
TIME (1µs/div)
VOLTAGE (1V/div)
OUT
Figure 11. Shutdown Output Voltage
SHDN
1V/div
TIME (1µs/div)
SUPPLY
CURRENT
500µA/div
Figure 12. Shutdown Enable/Disable Supply Current
MAX4130–MAX4134
Single/Dual/Quad, Wide-Bandwidth, Low-Power,
Single-Supply, Rail-to-Rail I/O Op Amps
14 ______________________________________________________________________________________
__________________________________________________________Pin Configurations
VEE
IN-
IN+
15VCC
OUT
MAX4130
SOT23
TOP VIEW
TOP VIEW
BUMPS ON BOTTOM
2
34
IN-
SHDN
VEE
OUT
VCC
IN+
MAX4131
UCSP
14
13
12
11
10
9
8
1
2
3
4
5
6
7
VCC
OUT2
IN2-
IN2+
VEE
IN1+
IN1-
OUT1
MAX4133
N.C.
SHDN2
N.C.
N.C.
SHDN1
N.C.
SO
14
13
12
11
10
9
8
1
2
3
4
5
6
7
OUT4
IN4-
IN4+
VEE
VCC
IN1+
IN1-
OUT1
MAX4134
IN3+
IN3-
OUT3
OUT2
IN2-
IN2+
SO
IN2-
IN1+
IN2+
VEE
1
2
8
7
VCC
OUT2
IN1-
OUT1
MAX4132
SO/µMAX
3
4
6
5
OUT
IN1+
N.C.
VEE
1
2
8
7
SHDN
VCC
IN1-
N.C.
MAX4131
SO/µMAX
3
4
6
5
B1 A1
B2 A2
B3 A3
MAX4130–MAX4134
Single/Dual/Quad, Wide-Bandwidth, Low-Power,
Single-Supply, Rail-to-Rail I/O Op Amps
______________________________________________________________________________________ 15
Chip Information
Ordering Information (continued)
MAX4130 TRANSISTOR COUNT: 170
MAX4131 TRANSISTOR COUNT: 170
MAX4132 TRANSISTOR COUNT: 340
MAX4134 TRANSISTOR COUNT: 680
*Dice are specified at TA= +25°C, DC parameters only.
PART TEMP RANGE PIN-
PACKAGE
TOP
MARK
MAX4132ESA -40°C to +85°C 8 SO —
MAX4132EUA -40°C to +85°C 8 µMAX —
MAX4133C/D 0°C to +70°C Dice* —
MAX4133ESD -40°C to +85°C 14 SO —
MAX4134ESD -40°C to +85°C 14 SO —
SOT-23 5L .EPS
E
1
1
21-0057
PACKAGE OUTLINE, SOT-23, 5L
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
MAX4130–MAX4134
Single/Dual/Quad, Wide-Bandwidth, Low-Power,
Single-Supply, Rail-to-Rail I/O Op Amps
16 ______________________________________________________________________________________
SOT23, 8L .EPS
REV.DOCUMENT CONTROL NO.APPROVAL
PROPRIETARY INFORMATION
TITLE:
3.002.60E
CE1
E
BETWEEN 0.08mm AND 0.15mm FROM LEAD TIP.
8. MEETS JEDEC MO178.
8
0.60
1.75
0.30
L2
0
e1
e
L
1.50E1
0.65 BSC.
1.95 REF.
0.25 BSC.
GAUGE PLANE
SEATING PLANE C
C
L
PIN 1
I.D. DOT
(SEE NOTE 6)
L
C
L
C
A2
e1
D
DETAIL "A"
5. COPLANARITY 4 MILS. MAX.
NOTE:
7. SOLDER THICKNESS MEASURED AT FLAT SECTION OF LEAD
6. PIN 1 I.D. DOT IS 0.3 MM MIN. LOCATED ABOVE PIN 1.
4. PACKAGE OUTLINE INCLUSIVE OF SOLDER PLATING.
3. PACKAGE OUTLINE EXCLUSIVE OF MOLD FLASH & METAL BURR.
HEEL OF THE LEAD PARALLEL TO SEATING PLANE C.
2. FOOT LENGTH MEASURED FROM LEAD TIP TO UPPER RADIUS OF
1. ALL DIMENSIONS ARE IN MILLIMETERS.
L2
L
A1
A
0.45
1.30
0.15
1.45
MAX
0.28b
0.90A2
0.00A1
0.90
A
MIN
SYMBOL
3.00
0.20
2.80D
0.09
C
SEE DETAIL "A"
L
C
be
D
1
21-0078
1
PACKAGE OUTLINE, SOT-23, 8L BODY
0
0
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
MAX4130–MAX4134
Single/Dual/Quad, Wide-Bandwidth, Low-Power,
Single-Supply, Rail-to-Rail I/O Op Amps
______________________________________________________________________________________ 17
6L, UCSP.EPS
G
1
1
21-0097
PACKAGE OUTLINE, 3x2 UCSP
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
18 __________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600
© 2003 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.
MAX4130–MAX4134
Single/Dual/Quad, Wide-Bandwidth, Low-Power,
Single-Supply, Rail-to-Rail I/O Op Amps
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
18 __________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600
© 2003 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.
SOICN .EPS
PACKAGE OUTLINE, .150" SOIC
1
1
21-0041 B
REV.DOCUMENT CONTROL NO.APPROVAL
PROPRIETARY INFORMATION
TITLE:
TOP VIEW
FRONT VIEW
MAX
0.010
0.069
0.019
0.157
0.010
INCHES
0.150
0.007
E
C
DIM
0.014
0.004
B
A1
MIN
0.053A
0.19
3.80 4.00
0.25
MILLIMETERS
0.10
0.35
1.35
MIN
0.49
0.25
MAX
1.75
0.050
0.016L0.40 1.27
0.3940.386D
D
MINDIM
D
INCHES
MAX
9.80 10.00
MILLIMETERS
MIN MAX
16 AC
0.337 0.344 AB8.758.55 14
0.189 0.197 AA5.004.80 8
N MS012
N
SIDE VIEW
H 0.2440.228 5.80 6.20
e 0.050 BSC 1.27 BSC
C
HE
eBA1
A
D
0-8
L
1
VARIATIONS:
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
