Doc. No.1P034-00 Product Specifications Standard Description 2.7" TFT EPD Panel Model Name EM027AS013 Date 2013/06/26 Doc. No. 1P034-00 Revision 02 PL AY S IN C . Customer VA Date SI VE D IS Customer Approval PE R The above signature represents that the product specifications, testing regulation, and warranty in the specifications are accepted Design Engineering Approval Check Design 2013.6.26 2013.6.26 2013.6.26 No.71, Delun Rd., Rende Dist., Tainan City 71743, Taiwan (R.O.C.) Tel: +886-6-279-5399 Rev.: 02 Fax: +886-6-279-5300 Page: 1 of 29 Date: 2013/06/26 This document is the exclusive property of PDI and shall not be reproduced or copied or transformed to any other format without prior permission of PDI. ( PDI Confidential ) Doc. No.1P034-00 Copyright Pervasive Displays Incorporated All rights reserved. This document is the exclusive property of Pervasive Displays Inc. (PDI) and shall not be reproduced or copied or transformed to any other format without prior permission of PDI. ( PDI Confidential ) Pervasive Displays Inc. C . No.71, Delun Rd., Rende Dist., Tainan City 71743, Taiwan (R.O.C.) IN Tel: +886-6-279-5399 PE R VA SI VE D IS PL AY S http://www.pervasivedisplays.com Rev.: 02 Page: 2 of 29 Date: 2013/06/26 This document is the exclusive property of PDI and shall not be reproduced or copied or transformed to any other format without prior permission of PDI. ( PDI Confidential ) Doc. No.1P034-00 Table of Contents Revision History ......................................................................................................... 6 Glossary of Acronyms ................................................................................................. 7 1.2 Features .................................................................................................... 8 1.3 Applications ................................................................................................ 8 1.4 General Specifications .................................................................................. 9 1.5 Mechanical Specifications ........................................................................... 10 C . Overview.................................................................................................... 8 IN Absolute Maximum Ratings ................................................................................... 12 Absolute Ratings of Environment ................................................................. 12 2.2 Reliability Test Item ................................................................................... 13 S 2.1 Electrical Characteristics ...................................................................................... 14 AY 3 1.1 3.1 Absolute Maximum Ratings of Panel ............................................................. 14 3.2 Recommended Operation Conditions of Panel ................................................ 14 PL 2 General Description ............................................................................................... 8 D IS 1 4 Application Circuit Block Diagram .......................................................................... 16 5 Terminal Pin Assignment & Reference Circuit ........................................................... 17 5.2 Reference Circuit ....................................................................................... 19 SI VE Terminal Pin Assignment ............................................................................ 17 VA Optical Characteristics ......................................................................................... 20 6.1 Test Conditions ......................................................................................... 20 6.2 Optical Specifications ................................................................................. 20 R 6 5.1 PE 6.2.1 Optical ..................................................................................................... 20 6.2.2 Ghosting .................................................................................................. 23 7 Packing ............................................................................................................. 24 8 Precautions ........................................................................................................ 26 9 Definition of Labels.............................................................................................. 28 Rev.: 02 Page: 3 of 29 Date: 2013/06/26 This document is the exclusive property of PDI and shall not be reproduced or copied or transformed to any other format without prior permission of PDI. ( PDI Confidential ) Doc. No.1P034-00 List of Figures Figure 1-1 EPD Drawing................................................................................ 11 Figure 2-1 Operating Range of Relative Humidity and Temperature ..................... 12 Figure 3-1 Test Pattern of Panel ..................................................................... 15 Figure 3-2 Image Update Current Profile ......................................................... 15 Figure 3-3 Current Measurement ................................................................... 15 Figure 4-1 Application Circuit Block Diagram.................................................... 16 Figure 5-1 EPD Reference Circuit ................................................................... 19 Optical measurement .................................................................... 21 Figure 6-2 Definition of Viewing Angle to Measure Contrast Ratio........................ 22 C . Figure 6-1 IN Figure 7-1 Packing Diagram .......................................................................... 24 Model Labels................................................................................ 28 Figure 9-2 Definition of Model Labels .............................................................. 28 AY S Figure 9-1 Figure 9-3 Carton Label ................................................................................ 29 PE R VA SI VE D IS PL Figure 9-4 Pallet Label .................................................................................. 29 Rev.: 02 Page: 4 of 29 Date: 2013/06/26 This document is the exclusive property of PDI and shall not be reproduced or copied or transformed to any other format without prior permission of PDI. ( PDI Confidential ) Doc. No.1P034-00 List of Tables General Specification ........................................................................ 9 Table 1-2 Mechanical Specification ................................................................. 10 Table 1-3 FPC Specification ........................................................................... 10 Table 2-1 Absolute Ratings of Environment ...................................................... 12 Table 2-2 Reliability Test Items ...................................................................... 13 Table 3-1 Absolute Maximum Ratings of Panel.................................................. 14 Table 3-2 Recommended Operation Conditions of Panel ..................................... 14 Table 5-1 Terminal Pin Assignment ................................................................. 17 Table 6-1 Optical Test Conditions ................................................................... 20 Table 6-2 Optical Measurement with D65 light source ....................................... 20 Table 6-3 Measurement of Ghosting ............................................................... 23 PE R VA SI VE D IS PL AY S IN C . Table 1-1 Rev.: 02 Page: 5 of 29 Date: 2013/06/26 This document is the exclusive property of PDI and shall not be reproduced or copied or transformed to any other format without prior permission of PDI. ( PDI Confidential ) Doc. No.1P034-00 Revision History Page Section (New) All 1 2 Product specification first issued. Cover Modify company address and Fax number. page Modify EPD drawing 11 1 13 2.2 15 3.2 17 5.1 Modify description in Terminal Pin Assignment 19 5.2 Modify Reference circuit 23 6.2.2 Add Note 3 at Reliability Test Items Add current value(MAX) Add Note description 2013/06/26 28 Modify definition of labels 9 PE R VA SI VE D IS 29 About refreshing of Test1 & Test2 had modified "1h storage" to "Refresh immediately", and to delete the PCS test. PL Ver.02 All C . 2012/06/30 IN Ver.01 Description S Date AY Version Rev.: 02 Page: 6 of 29 Date: 2013/06/26 This document is the exclusive property of PDI and shall not be reproduced or copied or transformed to any other format without prior permission of PDI. ( PDI Confidential ) Doc. No.1P034-00 Glossary of Acronyms Electrophoretic Display (e-Paper Display) EPD Panel EPD EPD Module EPD with TCon board TCon Timing Controller TFT Thin Film Transistor MCU Microcontroller Unit FPC Flexible Printed Circuit FPL Front Plane Laminate SPI Serial Peripheral Interface COG Chip on Glass PCS Print Contrast Signal PDI Pervasive Displays Incorporated PE R VA SI VE D IS PL AY S IN C . EPD Rev.: 02 Page: 7 of 29 Date: 2013/06/26 This document is the exclusive property of PDI and shall not be reproduced or copied or transformed to any other format without prior permission of PDI. ( PDI Confidential ) Doc. No.1P034-00 1 General Description 1.1 Overview This is a 2.7" a-Si, active matrix TFT, Electronic Paper Display (EPD) panel. The panel has such high resolution (117 dpi) that it is able to easily display fine patterns. Due to its bi-stable nature, the EPD panel requires very little power to update and needs no power to maintain an image. 1.2 Features a-Si TFT active matrix Electronic Paper Display(EPD) - Resolution: 264 x 176 - Ultra low power consumption - Super Wide Viewing Angle - near 180 - Extra thin & light - SPI interface - RoHS compliant D IS PL AY S IN C . - SI VE 1.3 Applications Electronic shelf label (ESL) - Reusable container - Badge PE R VA - Rev.: 02 Page: 8 of 29 Date: 2013/06/26 This document is the exclusive property of PDI and shall not be reproduced or copied or transformed to any other format without prior permission of PDI. ( PDI Confidential ) Doc. No.1P034-00 1.4 General Specifications Table 1-1 General Specification Specification Unit Note Outline Dimension 70.42(H) x 45.80(V) x 1.00(T) mm (1) Active Area 57.288(H) x 38.192(V) mm Driver Element a-Si TFT active matrix - FPL V110 - Pixel Number 264 x 176 Pixel Pitch 0.217 x 0.217 (117dpi) Pixel Arrangement Vertical stripe Display Colors Black/White Surface Treatment Anti-Glare pixel mm - D IS PL AY S IN C . Item PE R VA SI VE Note (1): Not including the FPC. Rev.: 02 Page: 9 of 29 Date: 2013/06/26 This document is the exclusive property of PDI and shall not be reproduced or copied or transformed to any other format without prior permission of PDI. ( PDI Confidential ) Doc. No.1P034-00 1.5 Mechanical Specifications Mechanical Specification Glass Size Min. Typ. Max. Unit Horizontal(H) 70.12 70.42 70.72 mm Vertical(V) 45.50 45.80 46.10 mm 0.80 1.00 1.20 mm - 6.30 7.7 g Thickness(T) Weight FPC Specification Pin numbers Golden Finger 40 Pitch (mm) Connector Note PL Item AY Table 1-3 (1) S Note (1): Not including the Masking Film. Note C . Item IN Table 1-2 PE R VA SI VE D IS 0.5 Rev.: 02 Page: 10 of 29 Date: 2013/06/26 This document is the exclusive property of PDI and shall not be reproduced or copied or transformed to any other format without prior permission of PDI. ( PDI Confidential ) Doc. No.1P034-00 EPD Drawing PE R VA SI VE D IS PL AY S IN C . Figure 1-1 General tolerance: 0.3mm Rev.: 02 Page: 11 of 29 Date: 2013/06/26 This document is the exclusive property of PDI and shall not be reproduced or copied or transformed to any other format without prior permission of PDI. ( PDI Confidential ) Doc. No.1P034-00 2 Absolute Maximum Ratings 2.1 Absolute Ratings of Environment Table 2-1 Absolute Ratings of Environment Item Symbol Value Min. Max. Unit Note TST -20 +60 C (1) Operating Ambient Temperature TOP 0 +50 C (1), (2) IN Note (1): C . Storage Temperature S (a) 90 %RH Max. (Ta 40 C), where Ta is ambient temperature. AY (b) Wet-bulb temperature should be 39 C Max. (Ta > 40 C). PL (c) No condensation. D IS Note (2): The temperature of panel display surface area should be 0 C Min. and 50 C Max. Refresh time depends on operation temperature. Operating Range of Relative Humidity and Temperature VE Figure 2-1 VA SI Relative Humidity(%RH) 90 PE R 100 Storage Range Operating Range 20 -20 Rev.: 02 0 Temperature(degree C) Page: 12 of 29 50 60 Date: 2013/06/26 This document is the exclusive property of PDI and shall not be reproduced or copied or transformed to any other format without prior permission of PDI. ( PDI Confidential ) Doc. No.1P034-00 2.2 Reliability Test Item Table 2-2 Reliability Test Items Item Test Condition Remark High Temperature Operation 50 for 240h (1) (2) Low Temperature Operation 0 for 240h (1) (2) High Temperature/Humidity Operation 40 / 90 %RH for 168h (1) (2) High Temperature Storage 60 for 240h Low Temperature Storage -20 for 240h High Temperature/Humidity Storage 50 / 80 %RH for 168h Thermal Cycles ( Non-operation ) 1 Cycle:-20/30min 60/30min, for 100 Cycles C . (1) (2)(3) IN (1) (2) (3) (1) (2) (3) PL AY S (1) (2) (3) D IS Drop from 97cm. ( ISTA ) Package Drop Test VE 1 corner, 3 edges, 6 sides. One drop for each. 1.15Grms, 1Hz ~ 200Hz. ( ISTA ) (1) (2) (3) SI Package Random Vibration Test (1) (2) (3) VA Note (1): End of test, function, mechanical, and optical shall be satisfied. PE R Note (2): The test result and judgment are based on PDI's 1bit driving waveform, driving fixture and driving system. Note (3): Test with white pattern Rev.: 02 Page: 13 of 29 Date: 2013/06/26 This document is the exclusive property of PDI and shall not be reproduced or copied or transformed to any other format without prior permission of PDI. ( PDI Confidential ) Doc. No.1P034-00 3 Electrical Characteristics 3.1 Absolute Maximum Ratings of Panel Table 3-1 Absolute Maximum Ratings of Panel Parameter Value Symbol Min Max Unit VDD -0.3 5.0 V Analog Power VCC -0.3 5.0 V Ground VSS - Connect VSS to Ground Ta = 25 2 C AY S IN - C . Digital Power Note Table 3-2 D IS PL 3.2 Recommended Operation Conditions of Panel Recommended Operation Conditions of Panel VDD 2.7 3.0 3.3 V VCC 2.7 3.0 3.3 V High VIH 0.8VDD - VDD V Low VIL VSS - 0.2VDD V High VOH 0.8VDD - VDD V IOH=0.5mA, SO, BUSY Low VOL VSS - 0.2VDD V IOL=-0.5mA, SO, BUSY High IIH - - 1.0 uA Low IIL - - -1.0 uA R VA SI Max PE Input Leakage Current Rev.: 02 Note Typ Analog Power Output Voltage Unit Min Digital Power Input Voltage Value Symbol VE Parameter Page: 14 of 29 /CS, ID, SCLK, SI, /RESET Date: 2013/06/26 This document is the exclusive property of PDI and shall not be reproduced or copied or transformed to any other format without prior permission of PDI. ( PDI Confidential ) Doc. No.1P034-00 Input Current IDD + ICC - 6 10 mA (1),(2),(3) IPEAK - 40 100 mA (1),(2),(3) DC/DC Inrush Current Ta = 25 2 C Note (1): Test Pattern of Panel IN These currents are tested with PDI test jig. C . Figure 3-1 S Note (2): Image Update Current Profile VA SI VE D IS PL Figure 3-2 AY VDD=VCC=3.0V PE R The "Time of DC/DC ON" which contains the some current peak of VGH/VDH/VGL/VDL/VCOM. Note (3): Figure 3-3 Current Measurement Computer Tektronix TCPA300 Amplifier USB Cable PDI Pattern Generator Board Rev.: 02 Tektronix DPO4054 Digital Phosphor Oscilloscope 10pin FFC PDI Timing Controller Board IDD+ICC(RMS) / IPEAK EPD Module Tektronix Current Probe TCP312 Page: 15 of 29 Date: 2013/06/26 This document is the exclusive property of PDI and shall not be reproduced or copied or transformed to any other format without prior permission of PDI. ( PDI Confidential ) Doc. No.1P034-00 4 Application Circuit Block Diagram Figure 4-1 Application Circuit Block Diagram Temperature Sensor Frame Memory e-Paper Panel Pin.1 SPI FPC VCC/VDD C . EPD Timing Controller Pin.40 IN System Host (MCU) PE R VA SI VE D IS PL AY S Driver IC Rev.: 02 Page: 16 of 29 Date: 2013/06/26 This document is the exclusive property of PDI and shall not be reproduced or copied or transformed to any other format without prior permission of PDI. ( PDI Confidential ) Doc. No.1P034-00 5 Terminal Pin Assignment & Reference Circuit 5.1 Terminal Pin Assignment Table 5-1 Terminal Pin Assignment Signal Type Connected to Function 1 /CS I Tcon Chip Select. Low enable 2 BUSY O Tcon When BUSY = HIGH, EPD stays in busy state that EPD ignores any input data from SPI 3 ID I Ground 4 SCLK I Tcon 5 SI I Tcon 6 SO O Tcon 7 /RESET I 8 ADC_IN - 9 VCL C 10 C42P 11 C42M 12 C41P C C41M C 14 C31M C 15 C31P C 16 C21M C 17 C21P C 18 C16M C 19 C16P C 20 C15M C 21 C15P C C . No. IN Connect ID to ground S Clock for SPI Rev.: 02 C AY PL D IS VE - Capacitor SI VA R PE 13 Tcon C Serial input from Timing Controller to EPD Charge-Pump Capacitor Charge-Pump Capacitor Charge-Pump Capacitor Charge-Pump Capacitor Charge-Pump Capacitor Charge-Pump Capacitor Page: 17 of 29 Serial output from EPD to Timing Controller Reset signal. Low enable Not connected Date: 2013/06/26 This document is the exclusive property of PDI and shall not be reproduced or copied or transformed to any other format without prior permission of PDI. ( PDI Confidential ) 22 C14M C 23 C14P C 24 C13M C 25 C13P C 26 C12M C 27 C12P C 28 C11M C 29 C11P C 30 VCOM_DRIVER RC Resistor & Capacitor 31 VCC P VCC 32 VDD P VDD 33 VSS P Ground - 34 VGH C Capacitor - 35 VGL C 36 VDH C 37 VDL 38 BORDER 39 PE Doc. No.1P034-00 40 Charge-Pump Capacitor The signal duty cycle can drive VCOM voltage from source driver IC Power supply for analog part of source driver VE D IS PL AY S Charge-Pump Capacitor - C . Charge-Pump Capacitor - IN Charge-Pump Capacitor Power supply for digital part of source driver - Capacitor - C Capacitor - I - VST P VCOM_PANEL - VCOM_PANEL C Capacitor VCOM to panel R VA SI Capacitor Connect to VDL via control circuit for white frame border Note: Type: I: Input O: Output C: Capacitor RC: Resistor and Capacitor P: Rev.: 02 Power Page: 18 of 29 Date: 2013/06/26 This document is the exclusive property of PDI and shall not be reproduced or copied or transformed to any other format without prior permission of PDI. ( PDI Confidential ) Doc. No.1P034-00 5.2 Reference Circuit Figure 5-1 EPD Reference Circuit INPUT J1 /CS BUSY Connect to Timing Controller SPI Connect to Timing Controller GPIO to to to to Timing Timing Timing Timing Controller Controller Controller Controller SPI SPI SPI GPIO C1 2.2u/10V/Y 5V BORDER VCL C42P C42M C41P C41M C31M C31P C21M C21P C16M C16P C15M C15P C14M C14P C13M C13P C12M C12P C11M C11P C2 2.2u/16V/Y 5V R1 0R/NC (Reserv ed f or test) C3 2.2u/16V/Y 5V C4 2.2u/25V/Y 5V 2.2u/25V/Y5V C7 2.2u/25V/Y5V C8 2.2u/16V/Y 5V C9 Connect to Power Ground 2.2u/16V/Y 5V 2.2u/16V/Y 5V S C10 IN C6 C . C5 2.2u/25V/Y5V C11 AY C12 1u/10V/X7R Connect to Power Switch PL VGH 2N7002KW Q1 VDH 2N7002KW DISCHARGE 1 2 Connect to Timing Controller GPIO PWM PWM: 100~300KHz, 50% duty cycle, square wave SI 100n/16V/X7R 3 Connect to Timing Controller GPIO VE DISCHARGE: set high for EPD discharge when EPD power off Q2 VA C17 R2 VCOM_DRIVER 2K/5% VCC VDD VGH ZIF-40-0.5 2.2u/25V/Y5V VGL D IS C13 3 2 1 2.2u/16V/Y 5V C14 2.2u/25V/Y5V C15 2.2u/25V/Y5V C16 2.2u/25V/Y5V VDH VDL BORDER VST Q3 2N7002KW BORDER 2 3 1 3 Connect to a MOS Switch to prevent leakage current VCOM /CS BUSY ID SCLK SI SO /RESET ADC_IN VCL C42P C42M C41P C41M C31M C31P C21M C21P C16M C16P C15M C15P C14M C14P C13M C13P C12M C12P C11M C11P VCOM_DRIVER VCC VDD VSS VGH VGL VDH VDL BORDER VST VCOM_PANEL 100K/5% R3 100K/5% VCOM R4 R5 100K/5% 1VGL BAT54SW 3 Q4 BSS84W 1 2 BORDER_CONTROL PE Connect to Timing Controller GPIO 2 R D1 VCC BORDER_CONTROL : Square Pulse when power on Note: (1) VDD and VCC must be discharged promptly after power off. Rev.: 02 Page: 19 of 29 Date: 2013/06/26 This document is the exclusive property of PDI and shall not be reproduced or copied or transformed to any other format without prior permission of PDI. ( PDI Confidential ) 40PIN 0.5mm PITCH CONNECTOR/PAD EPD PANEL PCB SIDE Connect Connect Connect Connect SCLK SI SO /RESET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Doc. No.1P034-00 6 Optical Characteristics 6.1 Test Conditions Table 6-1 Optical Test Conditions Value Unit Ambient Temperature Ta 252 C Ambient Humidity Ha 5010 %RH VCC & VDD 3.0 V Supply Voltage C . Symbol IN Item Table 6-2 PL Optical Optical Measurement with D65 light source Item Symbol Contrast ratio CR R PE White Chromaticity Reflectance Rev.: 02 Rating Max. 5:1 7:1 - - Tr - 3 - sec Wx - 0.313 - SI VE Min. Unit Typ. VA Refresh time D IS 6.2.1 AY S 6.2 Optical Specifications Wy - 0.338 - R% 25 32 - Page: 20 of 29 Note x=y=0 (1),(2),(3),(4) (3) x=y=0 - (1),(4) % (1),(4) Date: 2013/06/26 This document is the exclusive property of PDI and shall not be reproduced or copied or transformed to any other format without prior permission of PDI. ( PDI Confidential ) Doc. No.1P034-00 Note (1): Panel is driven by PDI waveform without masking film and optical measurement by CM-700D with D65 light source and SCE mode. Figure 6-1 Optical measurement PE R VA SI VE D IS PL AY S IN C . SCE mode Rev.: 02 Page: 21 of 29 Date: 2013/06/26 This document is the exclusive property of PDI and shall not be reproduced or copied or transformed to any other format without prior permission of PDI. ( PDI Confidential ) Doc. No.1P034-00 Note (2): Definition of Viewing Angle (x, y): Definition of Viewing Angle to Measure Contrast Ratio D IS PL AY S IN C . Figure 6-2 SI VE Note (3): Refresh time is the time that e-paper particles move not including the power on and off time. The refresh time is measured at 25C.The refresh time and contrast ratio varies due to different films, display performance requirements, and ambient temperatures. PE R VA Note (4): Contrast ratio (C.R.): The Contrast ratio is calculated by the following expression. C.R. =(R% White) / (R% Black). Reflectance is measured at 120 seconds after refresh. Rev.: 02 Page: 22 of 29 Date: 2013/06/26 This document is the exclusive property of PDI and shall not be reproduced or copied or transformed to any other format without prior permission of PDI. ( PDI Confidential ) Doc. No.1P034-00 6.2.2 Ghosting Below are two test methods to verify that ghosting within an acceptable range. Test 1 and Test 2 use measured data to calculate Delta E which is a single number representing the distance between two colors in a 3 dimensional color space. Test 1 and Test 2 are performed at 25C. Test 1: White to Black Ghosting White White Black A A' Measuring L, a, b of A and A', and calculate the E*ab Refresh immediately Black White Black B D IS Black AY Test 2: Black to White Ghosting PL y S IN Refresh immediately White C . y Refresh immediately B' Measuring L, a, b of B and B', and calculate the E*ab VE Refresh immediately SI The formula is used to calculate Test1 and Test2. For example of Test 2: VA E*ab = [ (LB - LB')2 + (aB - aB')2 + (bB - bB')2 ]1/2 PE R Table 6-3 Measurement of Ghosting Item Rating Min. Typ. Max. Test 1 E*ab - - 2 Test 2 E*ab - - 2 Note: Panel is driven by PDI waveform without masking film and optical measurement by CM-700D with D65 light source and SCE mode. Rev.: 02 Page: 23 of 29 Date: 2013/06/26 This document is the exclusive property of PDI and shall not be reproduced or copied or transformed to any other format without prior permission of PDI. ( PDI Confidential ) Doc. No.1P034-00 7 Packing Figure 7-1 Packing Diagram 16set EPD Tray F/B-EPE Drier x2 Drier UP/DOW-EPE 17X16=272Pcs 2Pcs Empty Tray Drier C . 1Pcs Empty Tray R/L-EPE Plastic bag Carton_Label Carton VE D IS PL 1Pcs Empty Tray AY S IN 17Pcs Full Tray SI Vacuum Packaging PE R VA Note: Rev.: 02 Page: 24 of 29 Date: 2013/06/26 This document is the exclusive property of PDI and shall not be reproduced or copied or transformed to any other format without prior permission of PDI. ( PDI Confidential ) Doc. No.1P034-00 Pallet Label S IN C . Film PL Pallet PP Belt AY Protector SI VE D IS 272(pcs) x 40(BOX)=10,880pcs PE R VA Sea / Land / Air Transportation Rev.: 02 Page: 25 of 29 Date: 2013/06/26 This document is the exclusive property of PDI and shall not be reproduced or copied or transformed to any other format without prior permission of PDI. ( PDI Confidential ) Doc. No.1P034-00 8 Precautions The EPD Panel / Module is manufactured from fragile materials such as glass and plastic, and may be broken or cracked if dropped. Please handle with care. Do not apply force such as bending or twisting to the EPD panel during assembly. (2) It is recommended to assemble or install EPD panels in a clean working area. Dust and oil may cause electrical shorts or degrade the protection sheet film. (3) Do not apply pressure to the EPD panel in order to prevent damaging it. (4) Do not connect or disconnect the interface connector while the EPD panel is in operation. (5) Please support the bezel with your finger while connecting the interface cable such as the FPC. (6) Do not stack the EPD panels / Modules. (7) Do not press the FPC on the glass edge or Pull FPC up / down to 90. (8) Do not touch the FPC lead connector. (9) Wear a Wrist Strap (Grounding connect) when handling and during assembly. Semiconductor devices are included in the EPD Panel / Module and they should be handled with care to prevent any electrostatic discharge (ESD). (An Ion Fan may be needed in assembly operation to reduce ESD risk.) PL AY S IN C . (1) D IS (10) Keep the EPD Panel / Module in the specified environment and original packing boxes when storage in order to avoid scratching. VE (11) Do not disassemble or reassemble the EPD panel. SI (12) Use a soft dry cloth without chemicals for cleaning. The surface of the protection sheet film is very soft and easily scratched. VA (13) Be mindful of moisture to avoid its penetration into the EPD panel, which may cause damage during operation. PE R (14) High temperature, high humidity, sunlight or fluorescent light may degrade the EPD panel's performance. Please do not expose the unprotected EPD panel to high temperature, high humidity, sunlight, or fluorescent for long periods of time. It is highly recommended to store the EPD panel in a dark place without condensation, a temperature range of 15C to 35C, and humidity from 30%RH to 60%RH. (15) The ink used for marking the Panel ID number is erased easily by solvent. Please avoid using solvent to clean the EPD panel. (16) The EPD is vacuum packed. (17) Before approved by PDI and customer, products and product specifications may be subject to change without notice. Confirm that you have received the latest product standards or specifications before final design, purchase or use. (18) PDI makes every attempt to ensure that its products are of high quality and reliability. However, contact PDI sales office before using the product in an application that demands especially high quality and reliability or where its failure or malfunction may directly threaten human life or cause risk of bodily injury, such as aerospace, aeronautics, nuclear power, combustion control, transportation, traffic, safety equipment or medical equipment for life support. Rev.: 02 Page: 26 of 29 Date: 2013/06/26 This document is the exclusive property of PDI and shall not be reproduced or copied or transformed to any other format without prior permission of PDI. ( PDI Confidential ) Doc. No.1P034-00 (19) Design your application so that the product is used within the ranges guaranteed by PDI particularly for maximum rating, operating supply voltage range, heat radiation characteristics, installation conditions and other characteristics. PDI bears no responsibility for failure or damage when used beyond the guaranteed ranges. Even within the guaranteed ranges, consider normally foreseeable failure rates or failure modes in semiconductor devices and employ systemic measures such as fail safes, so that the equipment incorporating PDI product does not cause bodily injury, fire or other consequential damage due to operation of the PDI product. PE R VA SI VE D IS PL AY S IN C . (20) This product is not designed to be radiation resistant. Rev.: 02 Page: 27 of 29 Date: 2013/06/26 This document is the exclusive property of PDI and shall not be reproduced or copied or transformed to any other format without prior permission of PDI. ( PDI Confidential ) Doc. No.1P034-00 9 Definition of Labels Figure 9-1 Model Labels Model Label 1 for preceding process XXXXXXXXXXXXXXXXXXXX S IN C . Barcode=ID No.(20 Digits) AY Model Label 2 for posterior process Barcode=ID No.(18 Digits) Definition of Model Labels SI Figure 9-2 XEXXXXXXXXXXXXXXXX VE D IS PL XXXXXXXXXX-XX VA ID NO. definition of Model Label 1 PE R XXXXXXXXXXXXXXXXXXXX (8~20)TFT LOT NO. (5~7)FPL LOT NO. (2~4)Manufacture Year/Month/Day (1)Preceding process vender code ID NO. definition of Model Label 2 (1~12) Customs control information XXXXXXXXXX-XX XEXXXXXXXXXXXXXXXX (15~18)Serial NO. (12~14)Manufacture Year/Month/Day (2~11)Model Name (1)Posterior process vender code Rev.: 02 Page: 28 of 29 Date: 2013/06/26 This document is the exclusive property of PDI and shall not be reproduced or copied or transformed to any other format without prior permission of PDI. ( PDI Confidential ) Doc. No.1P034-00 Figure 9-3 Carton Label Model Name. (10 Digits) Carton Serial No. (9 Digits) Q'TY. (3 Digits) EXXXXXXXXX CXXXXXXXX Q'TY:XXX RoHS (3 Digits) XXXXXXXXXX-XX (10 Digits) (9 Digits) C . Customs control information Pallet Label D IS Figure 9-4 PL AY S Carton Label IN Bar Code=Model Name.+Carton Serial No.+Q'TY.(22 Digits) Model Name. (10 Digits) SI CXXXXXX GW:XXXXKg VA Pallet Serial No. (7 Digits) VE EXXXXXXXXX Q'TY. (5 Digits) PE R Weight. Q'TY:XXXXX RoHS PERVASIVEDISPLAYS (10 Digits) (7 Digits) (5 Digits) Bar Code=Model Name.+Pallet Serial No.+Q'TY.(22 Digits) Pallet Label Rev.: 02 Page: 29 of 29 Date: 2013/06/26 This document is the exclusive property of PDI and shall not be reproduced or copied or transformed to any other format without prior permission of PDI. ( PDI Confidential )