INCH-POUND MIL-M-38510/315D 27 October 2003 SUPERSEDING MIL-M-38510/315C 17 JANUARY 1984 MILITARY SPECIFICATION MICROCIRCUITS, DIGITAL, LOW-POWER SCHOTTKY TTL, COUNTERS, MONOLITHIC SILICON Inactive for new design after 18 April 1997. This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product herein shall consist of this specification sheet and MIL-PRF 38535 1. SCOPE 1.1 Scope. This specification covers the detail requirements for monolithic silicon, low power Schottky TTL, binary and decade counters. Two product assurance classes and a choice of case outlines/lead finish are provided for each type and are reflected in the complete part number. For this product, the requirements of MIL-M-38510 have been superseded by MIL-PRF-38535, (see 6.3). 1.2 Part or Identifying Number (PIN). The PIN should be in accordance with MIL-PRF-38535, and as specified herein. 1.2.1 Device types. The device types should be as follows: Device type 01 02 03 04 05 06 07 08 09 10 11 12 13 Circuit Decade counter 4-bit binary counter Synchronous 4-bit decade counter (asynchronous clear) Synchronous 4-bit binary counter (asynchronous clear) Synchronous 4-bit up/down decade counter Synchronous 4-bit up/down binary counter Synchronous 4-bit up/down decade counter (with clear) Synchronous 4-bit up/down binary counter (with clear) Synchronous 4-bit up/down binary counter (with mode control) Divide-by-twelve counter Synchronous 4-bit decade counter (with synchronous clear) Synchronous 4-bit binary counter (with synchronous clear) Synchronous 4-bit decade counter (with mode control) 1.2.2 Device class. The device class should be the product assurance level as defined in MIL-PRF-38535. Comments, suggestions, or questions on this document should be addressed to: Commander, Defense Supply Center Columbus, ATTN: DSCC-VAS, 3990 East Broad St., Columbus, OH 43216-5000, or emailed to bipolar@dscc.dla.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at www.dodssp.daps.mil. AMSC N/A FSC 5962 MIL-M-38510/315D 1.2.3 Case outlines. The case outlines should be as designated in MIL-STD-1835 and as follows: Outline letter A B C D E F 2 Descriptive designator Terminals 14 14 14 14 16 16 20 GDFP5-F14 or CDFP6-F14 GDFP4-F14 GDIP1-T14 or CDIP2-T14 GDFP1-F14 or CDFP2-F14 GDIP1-T16 or CDIP2-T16 GDFP2-F16 or CDFP3-F16 CQCC1-N20 Package style Flat pack Flat pack Dual-in-line Flat pack Dual-in-line Flat pack Square leadless chip carrier 1.3 Absolute maximum ratings. Supply voltage range ............................................................................. -0.5 V dc to 7.0 V dc Input voltage range ................................................................................ -1.2 V dc at -18 mA to 5.5 V dc Storage temperature range .................................................................... -65 to +150C Maximum power dissipation, (PD) 1/ : Device type 05, 06, 07, 08................................................................. 187 mW Device type 01, 02, 10....................................................................... 83 mW Device type 03, 04, 11, 12................................................................. 176 mW Device type 09, 13 ............................................................................ 193 mW Lead temperature (soldering, 10 seconds) ............................................. 300C Thermal resistance, junction to case (JC): Cases A, B, C, D, E, F, and 2 (See MIL-STD-1835) Junction temperature (TJ) 3/.................................................................... 175C 1.4 Recommended operating conditions. 2/ Maximum low level output current (IoL) ................................................... Supply voltage (VCC) .............................................................................. Minimum high-level input voltage (VIH) ................................................... Maximum low-level input voltage (VIL) .................................................... Normalized fanout (each output) Types 01, 02, 05, 06, 07, 08, 10........................................................ Types 03, 04, 09, 11, 12, 13.............................................................. Low-level ...................................................................................... High-level ..................................................................................... Width of input count pulse, tp(IN) Types 01, 02, 10 Input A, reset ................................................................................ Input B .......................................................................................... Types 07, 08 ..................................................................................... Width of reset pulse, tp(reset) Types 01, 02, 10 ............................................................................... Count enable time Type 09, enable ............................................................................... 4.0 mA 4.5 V dc minimum to 5.5 V dc maximum 2.0 V dc 0.7 V dc 10 maximum 10 maximum 20 maximum 15 ns minimum 30 ns minimum 20 ns minimum 25 ns minimum 40 ns minimum _______ 1/ Must withstand the added PD due to short-circuit test (e.g., IOS). 2/ A change of states on the U/ D input for device types 09 and 13 is not recommended when the clock input is low. This may result in an erroneous count. 3/ Maximum junction temperature shall not be exceeded except for allowable short duration burn-in screening conditions in accordance with MIL-PRF-38535. 2 MIL-M-38510/315D Input clock frequency, fclock Types 01, 02, 10 Input A .......................................................................................... 0 to 29 MHz Types 03, 04, 11, 12 ......................................................................... 0 to 22 MHz Types 09, 13 ..................................................................................... 0 to 18 MHz Types 07, 08 ..................................................................................... 0 to 20 MHz Types 05, 06 ..................................................................................... 0 to 25 MHz Width of clock pulse, tw(clock) Types 03, 06, 09, 11, 12, 13.............................................................. 25 ns minimum Types 04 ........................................................................................... 30 ns minimum Types 05 ........................................................................................... 20 ns minimum Width of clear pulse, tw (clear) Types 03, 04, 05, 06, 07, 08, 11, 12.................................................. 20 ns minimum Setup time, t(setup) Types 03, 11, 12 Enable P....................................................................................... Load ............................................................................................. Clear (types 11 and 12 only) ........................................................ Type 04 Enable P....................................................................................... Load ............................................................................................. Data inputs Types 03, 09, 11, 12, 13 ......................................................... Type 04 ................................................................................... Types 07, 08 ........................................................................ Type 05 Data, L inputs ............................................................................... 25 ns minimum 25 ns minimum 20 ns minimum 35 ns minimum 35 ns minimum 20 ns minimum 25 ns minimum 30 ns minimum 15 ns minimum U/ D input ..................................................................................... 30 ns minimum EP, ET inputs ............................................................................... 15 ns minimum Type 06 Data, L inputs ............................................................................... 25 ns minimum U/ D input ..................................................................................... EP, ET, inputs .............................................................................. Hold time at any input, t(hold) Types 09, 13 ..................................................................................... Types 07, 08 ..................................................................................... Types 05, 06 Data, EP, ET inputs ...................................................................... L, U/ D inputs ............................................................................... Types 03, 04, 11, 12 ......................................................................... Types 03, 04, 11, 12 tW (clear) ......................................................... Case operating temperature range (Tc)................................................... 30 ns minimum 25 ns minimum 0 ns minimum 10 ns minimum 5 ns minimum 0 ns minimum 10 ns minimum 0 ns minimum -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, or 5 of this specification, whether or not they are listed. 3 MIL-M-38510/315D 2.2 Government documents. 2.2.1 Specifications and Standards. The following specifications and standards form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-38535 - Integrated Circuits (Microcircuits) Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 MIL-STD-1835 - Test Method Standard for Microelectronics. Interface Standard Electronic Component Case Outlines (Copies of these documents are available online at http://assist.daps.dla.mil;quicksearch/ or www.dodssp.daps.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Qualification. Microcircuits furnished under this specification shall be products that are manufactured by a manufacturer authorized by the qualifying activity for listing on the applicable qualified manufacturers list before contract award (see 4.3 and 6.4). 3.2 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. 3.3 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein. 3.3.1 Terminal connections and logic diagrams. The terminal connections and logic diagrams shall be as specified on figures 1 and 2. 3.3.2 Truth tables. The truth tables and logic equations shall be as specified on figure 3. 3.3.4 Schematic circuits. The schematic circuits shall be maintained by the manufacturer and made available to the qualifying activity and the preparing activity (DSCC-VAS) upon request. 3.3.5 Case outlines. The case outlines shall be as specified in 1.2.3. 3.4 Lead material and finish. The lead material and finish shall be in accordance with MIL-PRF-38535 (see 6.6). 4 MIL-M-38510/315D 3.5 Electrical performance characteristics. The electrical performance characteristics are as specified in table I, and apply over the full recommended case operating temperature range, unless otherwise specified. 3.6 Electrical test requirements. The electrical test requirements for each device class shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table III. 3.7 Marking. Marking shall be in accordance with MIL-PRF-38535. 3.8 Microcircuit group assignment. The devices covered by this specification shall be in microcircuit group number 12 (see MIL-PRF-38535, appendix A). 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535 or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not effect the form, fit, or function as described herein. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38535 and shall be conducted on all devices prior to qualification and quality conformance inspection. The following additional criteria shall apply: a. The burn-in test duration, test condition, and test temperature, or approved alternatives shall be as specified in the device manufacturer's QM plan in accordance with MIL-PRF-38535. The burn-in test circuit shall be maintained under document control by the device manufacturer's Technology Review Board (TRB) in accordance with MILPRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II, except interim electrical parameters test prior to burn-in is optional at the discretion of the manufacturer. c. Additional screening for space level product shall be as specified in MIL-PRF-38535, appendix B. 5 MIL-M-38510/315D TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C < TC < +125C unless otherwise specified Limits Device types Min Max Unit Low-level output voltage VOL VCC = 4.5 V, VIH = 2.0 V VIL = 0.7 V, IOL = 4 mA 1/ All - 0.4 V High-level output voltage VOH VCC = 4.5 V, VIH = 2.0 V VIL = 0.7 V, IOH = -400m A All 2.5 - V Input clamp voltage VIC TC = 25C, VCC = 4.5 V IIN = -18 mA All - -1.5 V Low-level input current at reset inputs IIL1 VCC = 5.5 V, VIN = 0.4 V 01, 02, 10 -30 -400 A Low-level input current at input A Low-level input current at input B Low-level input current at data, clear, EnP Low-level input current at data, EnP Low-level input current at clear Low-level input current at load Low-level input current at EnT Low-level input current at clock Low-level input current at EnG Low-level input current at data, clock, down/up Low-level input current at load Low-level input current at data Low-level input current at load Low-level input current at clear, count up, count down Low-level input current at data Low-level input current at clock, down/up Low-level input current at EP Low-level input current at ET IIL2 -0.5 -2.4 mA IIL4 01, 02, 10 01, 10 02 03, 04 -0.4 -0.4 -30 -3.2 -1.6 -400 mA mA A IIL4 01, 12 -30 -400 A IIL4 01, 12 -30 -760 A IIL5 -30 -800 A -30 -860 A 0 -.630 mA -.15 -.36 -120 -1.08 -1.08 -400 mA IIL8 03, 04, 11, 12 03, 04, 11, 12 03, 04, 11, 12 09 13 09, 13 IIL8 09, 13 -100 -400 A IIL9 07, 08 -100 -400 A IIL10 07, 08 -100 -400 A IIL11 07, 08 -120 -400 A IIL12 05, 06 -3.0 -400 A IIL13 05, 06 -135 -370 A IIL14 05, 06 -150 -385 A IIL15 05, 06 -280 -760 A IIL3 IIL5 IIL6 IIL7 See footnotes at end of table. 6 A MIL-M-38510/315D TABLE I. Electrical performance characteristics. Test Symbol High-level input current at reset inputs IIH1 Conditions -55C < TC < +125C unless otherwise specified VCC = 5.5 V, VIN = 2.7 V High-level input current at reset inputs High-level input current at input A High-level input current at input A High-level input current at input B High-level input current at input B High-level input current at load, clock, EnT High-level input current at load, clock, EnT High-level input current at data, EnP High-level input current at data, EnP High-level input current at clear High-level input current at clear High-level input current at EnG High-level input current at EnG High-level input current at data, load, clear, count up, count down, clock, down/up High-level input current at data, load, clear, count up, count down, clock, down/up High-level input current at ET IIH2 VCC = 5.5 V, VIN = 5.5 V IIH3 VCC = 5.5 V, VIN = 2.7 V IIH4 VCC = 5.5 V, VIN = 5.5 V IIH5 VCC = 5.5 V, VIN = 2.7 V IIH6 VCC = 5.5 V, VIN = 5.5 V IIH9 VCC = 5.5 V, VIN = 2.7 V IIH10 VCC = 5.5 V, VIN = 5.5 V IIH11 VCC = 5.5 V, VIN = 2.7 V IIH12 VCC = 5.5 V, VIN = 5.5 V IIH13 VCC = 5.5 V, VIN = 2.7 V IIH14 VCC = 5.5 V, VIN = 5.5 V IIH15 VCC = 5.5 V, VIN = 2.7 V 01, 02 10 01, 02 10 01, 02, 10 01 02, 10 01 02, 10 03, 04, 11, 12 03, 04, 11, 12 03, 04, 11, 12 03, 04, 11, 12 03, 04, 11, 12 03, 04 11, 12 09, 13 IIH16 VCC = 5.5 V, VIN = 5.5 V 09, 13 - 300 A IIH17 VCC = 5.5 V, VIN = 2.7 V 05, 06 07, 08 09, 13 - 20 A IIH18 VCC = 5.5 V, VIN = 5.5 V 05, 06 07, 08 09, 13 - 100 A IIH19 VCC = 5.5 V, VIN = 2.7 V 05, 06 - 40 A See footnotes at end of table. 7 Device types Limits Unit Min Max 01, 02 10 - 20 A - 100 A - 80 A - 400 A - 160 80 800 400 40 A - 200 A - 20 A - 100 A - 20 40 100 200 60 A A A A A MIL-M-38510/315D TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C < TC < +125C unless otherwise specified High-level input current at ET IIH20 VCC = 5.5 V, VIN = 5.5 V Short circuit output current IOS VCC = 5.5 V 2/ Supply current ICC VCC = 5.5 V Limits Device types Min Max 05, 06 - 200 A All -15 -130 mA 15 mA 01,02,10 Unit 05,06,07,08 34 09, 13 35 High-level supply current ICCH VCC = 5.5 V, 3/ 03, 04, 11, 12 - 31 mA High-level supply current ICCH VCC = 5.5 V, 3/ 03, 04 11, 12 - 31 mA Low-level supply current ICCL VCC = 5.5 V, 4/ 03, 04 11, 12 - 32 mA Maximum input A, clock, or count up frequency FMAX VCC = 5.0 V, CL = 50 pF, 10% 05, 06 01, 02, 10 25 29 - MHz 03, 04, 07, 08, 11, 12 22 09, 13 18 - RL = 2 k Propagation delay time, high to low, A to QC tPHL1 01,02,10 3 81 ns Propagation delay time, low to high, A to QC tPLH1 01, 10 3 74 ns 02 3 74 01, 10 3 56 02 3 78 01, 10 3 52 02 3 78 Propagation delay time, high to low, B to QD Propagation delay time, low to high, B to QD tPHL2 tPLH2 ns ns Propagation delay time, low to high, clock to carry tPLH4 03, 04, 11, 12 3 56 ns Propagation delay time, high to low, clock to carry tPHL4 03, 04, 11, 12 3 56 ns See footnotes at end of table. 8 MIL-M-38510/315D TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C < TC < +125C unless otherwise specified Device types VCC = 5.0 V, CL = 50 pF, 10% Limits Unit Min Max 03, 04, 11, 12 3 41 ns Propagation delay time, low to high, clock to Q tPLH5 Propagation delay time, high to high, clock to Q tPHL5 03, 04, 11, 12 3 45 ns Propagation delay time, low to high, clock to Q tPLH5 05, 06 3 26 ns Propagation delay time, high to low, clock to Q tPHL5 05 3 26 ns 06 3 36 RL = 2 k Propagation delay time, low to high, clock (data) to Q Propagation delay time, high to low, clock (data) to Q Propagation delay time, low to high, EnT to carry tPLH6 03, 04, 11, 12 3 42 ns tPHL6 03, 04, 11, 12 3 48 ns tPLH7 03, 04, 11, 12 3 28 ns Propagation delay time, high to low, EnT to carry tPHL7 03, 04, 11, 12 3 28 ns Propagation delay time, low to high, ET to RC tPLH7 05 3 18 ns 06 3 28 05 3 28 06 3 32 Propagation delay time, high to low, ET to RC tPHL7 ns Propagation delay time, high to low, clear to Q tPHL8 03, 04, 11, 12 3 46 ns Propagation delay time, low to high, load to Q tPLH8 07, 08 3 63 ns Propagation delay time, high to low, load to Q tPHL10 07, 08 3 63 ns Propagation delay time, low to high, counts up tPLH9 07, 08 3 60 ns 05 3 26 06 3 32 and down to Q, U/ D to RC 9 MIL-M-38510/315D TABLE I. Electrical performance characteristics - Continued. Test Propagation delay time, high to low, counts up Symbol tPHL11 Conditions -55C < TC < +125C unless otherwise specified Device types Min Max VCC = 5.0 V, CL = 50 pF, 10% 07, 08 3 73 05 3 33 06 3 37 RL = 2 k and down to Q, U/ D to RC Limits Unit ns Propagation delay time, high to low, clear to Q tPHL12 07, 08 3 56 ns Propagation delay time, low to high, load to Q tPLH10 09, 13 3 53 ns Propagation delay time, high to low, load to Q tPHL13 09, 13 3 77 ns Propagation delay time, low to high, clock to Q tPLH11 09, 13 3 41 ns Propagation delay time, high to low, clock to Q tPHL14 09, 13 3 57 ns Propagation delay time, low to high, clock to Max Min Propagation delay time, low to high, clock to ripple carry Propagation delay time, high to low, clock to Max Min Propagation delay time, high to low, clock to ripple carry tPLH12 09, 13 3 66 ns tPLH12 05 3 35 ns 06 3 38 tPHL15 09, 13 3 80 ns tPHL15 05 3 37 ns 06 3 40 1/ Use IOL + IIL3(Max) for VOL test on QA. 2/ Not more than one output should be shorted at a time. 3/ ICCH is measured : (a) With the load input high; and (b) Then again with the load input low with all other inputs high and all outputs open. 4/ ICCL is measured: (a) With the clock input high; and (b) Then again with the clock input low with all other inputs low and all outputs open. 10 MIL-M-38510/315D TABLE II. Electrical test requirements. MIL-PRF-38535 test requirements Interim electrical parameters Final electrical test parameters Group A test requirements Group B test when using the method 5005 QCI option Group C end-point electrical parameters Group D end-point electrical parameters Subgroups (see table III) Class S Class B devices devices 1 1 1*, 2, 3, 7, 9, 10, 11 1, 2, 3, 7, 8, 9, 10, 11 1, 2, 3, 7 8, 9, 10, 11 1*, 2, 3, 7, 9 1, 2, 3, 7, 8, 9, 10, 11 N/A 1, 2, 3 1, 2, 3, 7, 8 9, 10, 11 1, 2, 3 1, 2, 3 *PDA applies to subgroup 1. 4.3 Qualification inspection. Qualification inspection shall be in accordance with MIL-PRF-38535 . 4.4 Technology Conformance inspection (TCI). Technology conformance inspection shall be in accordance with MILPRF-38535 and herein for groups A, B, C, and D inspections (see 4.4.1 through 4.4.4). 4.4.1 Group A inspection. Group A inspection shall be in accordance with table III of MIL-PRF-38535 and as follows: a. Tests shall be as specified in table II herein. b. Subgroups 4, 5, and 6 shall be omitted. 4.4.2 Group B inspection. Group B inspection shall be in accordance with table II MIL-PRF-38535. 4.4.3 Group C inspection. Group C inspection shall be in accordance with table IV of MIL-PRF-38535 and as follows: a. End-point electrical parameters shall be as specified in table II herein. b. The steady-state life test duration, test condition, and test temperature, or approved alternatives shall be as specified in the device manufacturer's QM plan in accordance with MIL-PRF-38535. The burn-in test circuit shall be maintained under document control by the device manufacturer's Technology Review Board (TRB) in accordance with MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1005 of MIL-STD-883. 4.4.4 Group D inspection. Group D inspection shall be in accordance with table V of MIL-PRF-38535. End-point electrical parameters shall be as specified in table II herein. 4.5 Methods of inspection. Methods of inspection shall be specified and as follows: 4.5.1 Voltage and current. All voltages given are referenced to the microcircuit ground terminal. Currents given are conventional and positive when flowing into the referenced terminal. 11 MIL-M-38510/315D Device type 01 Device type 02 Device type 03 Device type 04 CASES Pin number A, B, C, and D 2 A, B, C, and D 2 E,F 2 E,F 2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 BD INPUT (1) RO (2) RO NC VCC R9(1) R9(2) OUTPUT C OUTPUT B GND OUTPUT D OUTPUT A NC INPUT A N/C BD INPUT (1) RO (2) RO N/C N/C N/C VCC (1) R9 (2) R9 N/C OUTPUT C OUTPUT B GND N/C INPUT B RO(1) RO(2) NC N/C INPUT B (1) RO CLEAR CLOCK INPUT A INPUT B INPUT C INPUT D ENABLE P GND LOAD ENABLE T QD QC QB N/C CLEAR CLOCK INPUT A INPUT B N/C INPUT C INPUT D ENABLE P GND N/C LOAD T QD QC CLEAR CLOCK INPUT A INPUT B INPUT C INPUT D ENABLE P GND LOAD ENABLE T QD QC QB N/C CLEAR CLOCK INPUT A INPUT B N/C INPUT C INPUT D ENABLE P GND N/C LOAD T QD QC VCC NC NC OUTPUT C OUTPUT B GND OUTPUT D OUTPUT A NC INPUT A (2) RO N/C N/C N/C VCC N/C N/C N/C OUTPUT C OUTPUT B GND N/C 16 17 18 19 OUTPUT D N/C OUTPUT A N/C OUTPUT D N/C OUTPUT A N/C 20 INPUT A INPUT A QA CARRY OUTPUT VCC FIGURE 1. Terminal connections. 12 N/C QB QA CARRY OUTPUT VCC QA CARRY OUTPUT VCC N/C QB QA CARRY OUTPUT VCC MIL-M-38510/315D Device type 05 Device type 06 Device type 07 CASES E, F 2 Pin number E, F 2 E, F 2 1 U/ D N/C U/ D N/C 2 CK U/ D CK U/ D 3 4 INPUT A INPUT B CK INPUT A INPUT A INPUT B CK INPUT A 5 INPUT C INPUT B INPUT C INPUT B 6 7 INPUT D ENABLE P GND LOAD N/C INPUT C INPUT D ENABLE P GND LOAD N/C INPUT C 8 9 10 11 12 ENABLE T QD QC 13 QB 14 15 QA RIPPLE CARRY OUTPUT VCC 16 17 18 19 20 INPUT D ENABLE P GND N/C LOAD ENABLE T QD QC N/C QB QA RC OUTPUT VCC ENABLE T QD QC QB QA RIPPLE CARRY OUTPUT VCC INPUT D ENABLE P GND N/C LOAD DATA B INPUT QB QA COUNT DOWN COUNT UP QC QD GND DATA D DATA C LOAD CARRY ENABLE T QD QC BORROW N/C QB QA RC OUTPUT VCC VCC CLEAR DATA A N/C DATA B INPUT QB QA COUNT DOWN N/C COUNT UP QC QD GND N/C DATA D DATA C LOAD CARRY N/C BORROW CLEAR DATA A VCC FIGURE 1. Terminal connections - Continued. 13 Device type 08 E, F 2 DATA B INPUT QB N/C QA COUNT DOWN COUNT UP QC QD GND DATA D DATA C LOAD CARRY BORROW CLEAR DATA A VCC DATA B INPUT QB QA COUNT DOWN N/C COUNT UP QC QD GND N/C DATA D DATA C LOAD CARRY N/C BORROW CLEAR DATA A VCC MIL-M-38510/315D Device type 09 Device type 10 Device type 11 Device type 12 CASES Pin number E, F 2 A,B C, and D 2 E, F 2 E, F 2 1 DATA B N/C N/C CLEAR N/C CLEAR N/C 2 QB DATA B INPUT BC NC CLOCK CLEAR CLOCK CLEAR 3 4 QB QA NC NC INPUT A INPUT B CLOCK INPUT A INPUT A INPUT B CLOCK INPUT A N/C INPUT C INPUT B INPUT C INPUT B RO(1) RO(2) N/C N/C INPUT D ENABLE P N/C INPUT C INPUT D ENABLE P N/C INPUT C 8 9 GND DATA D ENABLE G N/C DOWN UP QC QD VCC 6 7 QA ENABLE G DOWN UP QC QD INPUT BC N/C N/C OUTPUT D OUTPUT C VCC (1) RO GND LOAD GND LOAD 10 11 12 DATA C LOAD MAX/ MIN RIPPLE CLOCK CLOCK DATA A GND N/C DATA D GND OUTPUT B OUTPUT A RO N/C OUTPUT D ENABLE T QD QC INPUT D ENABLE P GND N/C LOAD ENABLE T QD QC INPUT D ENABLE P GND N/C LOAD DATA C NC OUTPUT C QB T QB T LOAD MAX/ MIN N/C RC CLOCK DATA A INPUT A GND N/C QA CARRY OUTPUT VCC QD QC QA CARRY OUTPUT VCC QD QC 5 13 14 15 16 17 18 19 20 VCC VCC (2) OUTPUT B N/C OUTPUT A N/C INPUT A FIGURE 1. Terminal connections - Continued. 14 N/C QB QA CARRY OUTPUT VCC N/C QB QA CARRY OUTPUT VCC MIL-M-38510/315D Pin number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Device type 13 CASES E, F 2 DATA B QB QA ENABLE G DOWN UP QC QD GND DATA D DATA C LOAD MAX/ MIN RIPPLE CLOCK CLOCK DATA A VCC N/C DATA B QB QA ENABLE G N/C DOWN UP QC QD GND N/C DATA D DATA C LOAD MAX/ MIN N/C RC CLOCK DATA A VCC FIGURE 1. Terminal connections - Continued 15 MIL-M-38510/315D FIGURE 2. Logic diagrams 16 MIL-M-38510/315D FIGURE 2. Logic diagrams - Continued. 17 MIL-M-38510/315D FIGURE 2. Logic diagrams - Continued. 18 MIL-M-38510/315D FIGURE 2. Logic diagrams - Continued. 19 MIL-M-38510/315D FIGURE 2. Logic diagrams - Continued. 20 MIL-M-38510/315D FIGURE 2. Logic diagrams - Continued. 21 MIL-M-38510/315D FIGURE 2. Logic diagrams - Continued. 22 MIL-M-38510/315D FIGURE 2. Logic diagrams - Continued. 23 MIL-M-38510/315D FIGURE 2. Logic diagrams - Continued. 24 MIL-M-38510/315D FIGURE 2. Logic diagrams - Continued. 25 MIL-M-38510/315D FIGURE 2. Logic diagrams - Continued. 26 MIL-M-38510/315D FIGURE 2. Logic diagrams - Continued. 27 MIL-M-38510/315D FIGURE 2. Logic diagrams - Continued. 28 MIL-M-38510/315D FIGURE 2. Logic diagrams - Continued. 29 MIL-M-38510/315D FIGURE 2. Logic diagrams - Continued. 30 MIL-M-38510/315D FIGURE 2. Logic diagrams - Continued. 31 MIL-M-38510/315D FIGURE 2. Logic diagrams - Continued. 32 MIL-M-38510/315D FIGURE 2. Logic diagrams - Continued. 33 MIL-M-38510/315D FIGURE 2. Logic diagrams - Continued. 34 MIL-M-38510/315D FIGURE 2. Logic diagrams - Continued. 35 MIL-M-38510/315D FIGURE 2. Logic diagrams - Continued. 36 MIL-M-38510/315D FIGURE 2. Logic diagrams - Continued. 37 MIL-M-38510/315D FIGURE 2. Logic diagrams - Continued. 38 MIL-M-38510/315D FIGURE 2. Logic diagrams - Continued. 39 MIL-M-38510/315D FIGURE 2. Logic diagrams - Continued. 40 MIL-M-38510/315D FIGURE 2. Logic diagrams - Continued. 41 MIL-M-38510/315D DEVICE TYPE 01 BCD COUNT SEQUENCE (See Note A) COUNT 0 1 2 3 4 5 6 7 8 9 QD L L L L L L L L H H OUTPUT QC QB L L L L L H L H H L H L H H H H L L L L BI-QUINARY (5-2) (See Note B) COUNT QA L H L H L H L H L H 0 1 2 3 4 5 6 7 8 9 QA L L L L L H H H H H OUTPUT QD QC L L L L L H L H H L L L L L L H L H H L RESET/COUNT FUNCTION TABLE R0(1) H H X X L L X RESET INPUTS R0(2) R9(1) H L H X X H L X X L X X L L R9(2) X L H L X L X QD L L H OUTPUT QC QB L L L L L L COUNT COUNT COUNT COUNT NOTES: A. Output QA is connected to input B for BCD count. B. Output QD is connected to input A for bi-quinary count. FIGURE 3. Truth tables. 42 QA L L H QB L H L H L L H L H L MIL-M-38510/315D DEVICE TYE 02 DEVICE TYPE 10 COUNT SEQUENCE (See Note) COUNT 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 QD L L L L L L L L H H H H H H H H OUTPUT QC QB L L L L L H L H H L H L H H H H L L L L L H L H H L H L H H H H COUNT SEQUENCE (See Note) COUNT QA L H L H L H L H L H L H L H L H 0 1 2 3 4 5 6 7 8 9 10 11 RESET/COUNT FUNCTION TABLE RESET INPUTS R0(1) R0(2) H H L X X L QD L OUTPUT QC QB L L COUNT COUNT QD L L L L L L H H H H H H OUTPUT QC QB L L L L L H L H H L H L L L L L L H L H H L H L QA L H L H L H L H L H L H RESET/COUNT FUNCTION TABLE RESET INPUTS R0(1) R0(2) H H L X X L QA L NOTE: Output QA is connected to input B. QD L OUTPUT QC QB L L COUNT COUNT NOTE: Output QA is connected to input B. FIGURE 3. Truth tables. 43 QA L MIL-M-38510/315D SYNCHRONOUS TRUTH TABLE, DEVICE TYPES 3 AND 11 Input at time tn CP CP CP Enable P L X H Enable T X L H CP X CP CP X X Clock Outputs at time tn+1 Load A B C D Clear H H H X X X X X X X X X X X X H H H H L X X X X H L X L X X X X X X X X X H L QB QA QC QD NC NC NC NC NC NC NC NC Previous count plus 1 (note 1) A B C D A L B L C L D L Carry output NC L H if count = 9 L if count < 9 H if count = 9 L if count < 9 L L ASYNCHRONOUS TRUTH TABLE, DEVICE TYPE 3 Clock X Enable P X Inputs at time tn Enable Load A T X X X Outputs at time tn+1 B C D Clear QA QB QC QD X X X L L L L L NOTES: 1. See up count sequence table. 2. L = VIL for inputs, V0L for outputs. 3. H = VIH for inputs, V0H for outputs. 4. X = VIH or VIL. 5. CP = Clock pulse. 6. NC = No change. Carry output L UP COUNT SEQUENCE TABLE QA (LSB) L H L H L H L H L H QB QC L L H H L L H H L L L L L L H H H H L L FIGURE 3. Truth tables - Continued. 44 QD (MSB) L L L L L L L L H H MIL-M-38510/315D SYNCHRONOUS TRUTH TABLE, DEVICE TYPES 4 AND 12 Input at time tn CP CP CP Enable P L X H Enable T X L H CP X CP CP X X Clock Outputs at time tn+1 Load A B C D Clear H H H X X X X X X X X X X X X H H H H L X X X X H L X L X X X X X X X X X H L QA QB QC QD NC NC NC NC NC NC NC NC Previous count plus 1 (note 1) A B C D A L B L C L D L Carry output NC L H if count = 15 L if count < 15 H if count = 15 L if count < 15 L L ASYNCHRONOUS TRUTH TABLE, DEVICE TYPE 4 Clock X Enable P X Inputs at time tn Enable Load A T X X X Outputs at time tn+1 B C D Clear QA QB QC QD X X X L L L L L Carry output L NOTES: 1. See up count sequence table. 2. L = VIL for inputs, V0L for outputs. 3. H = VIH for inputs, V0H for outputs. 4. X = VIH or VIL. 5. CP = Clock pulse. 6. NC = No change. UP COUNT SEQUENCE TABLE QA (LSB) L H L H L H L H L H L H L H L H QB QC L L H H L L H H L L H H L L H H L L L L H H H H L L L L H H H H FIGURE 3. Truth tables - Continued. 45 QD (MSB) L L L L L L L L H H H H H H H H MIL-M-38510/315D Device type 05 Device type 06 UP COUNT SEQUENCE TABLE QA (LSB) L H L H L H L H L H QB QC L L H H L L H H L L L L L L H H H H L L UP COUNT SEQUENCE TABLE QA (LSB) L H L H L H L H L H L H L H L H QD (MSB) L L L L L L L L H H QB QC L L H H L L H H L L H H L L H H L L L L H H H H L L L L H H H H Device types 05 and 06 MODE SELECT TABLE L EP ET L H H H H X L L H X X L L X H U/ D X H L X X Action on Rising Clock Edge Load (Dn Qn) Count Up (increment) Count Down (decrement) No Change (Hold) No Change (Hold) H = High voltage level L = Low voltage X = Don't care FIGURE 3. Truth tables - Continued. 46 QD (MSB) L L L L L L L L H H H H H H H H MIL-M-38510/315D DEVICE TYPE 7 TRUTH TABLE Outputs at time tn=1 Inputs at time tn Count Up H H H P Count Down H H H H Load H H L H A X X X X B X X X X C X X X X D X X X X Clear L H L L H P H X X X X L N H H X X X X L QC QD QA QB NC NC NC NC L L L L A B C D Previous count plus 1 (note 1) Previous count minus 1 (note 2) NC NC NC NC H N H X X X X L NC NC NC NC NOTES: 1. See up count sequence table. 2. See down count sequence table. 3. L= VIL for inputs, VOL for outputs. 4. H = VIH for inputs, VOH for outputs. 5. X = VIH or VIL. 6. NC = No change. 7. NA = Not applicable. 8. P = Positive going pulse. 9. N= Negative going pulse. FIGURE 3. Truth tables - Continued. 47 Carry H H H H Borrow H H H H H H N if count = 9 H if count 9 H H N if count = 0 H if count 0 MIL-M-38510/315D DEVICE TYPE 07 UP COUNT SEQUENCE TABLE QA (LSB) L H L H L H L H L H QB QC L L H H L L H H L L L L L L H H H H L L DOWN COUNT SEQUENCE TABLE Carry QD (MSB) L L L L L L L L H H QA (LSB) H L H L H L H L H L H H H H H H H H H L QB QC L L H H L L H H L L L L H H H H L L L L QD (MSB) H H L L L L L L L L Borrow H H H H H H H H H L DEVICE TYPE 8 TRUTH TABLE Outputs at time tn=1 Input at time tn Count up H H H P Count down H H H H Load H H L H A X X X X B X X X X C X X X X D X X X X Clear L H L L H P H X X X X L N H H X X X X L QC QD QA QB NC NC NC NC L L L L A B C D Previous count plus 1 (note) Previous count minus 1 (note 2) NC NC NC NC H N H X X X X L NC NC NC NC NOTES: 1. See up count sequence table. 2. See down count sequence table. 3. L = VIL for inputs, VOL for outputs. 4. H = VIH for inputs, VOH for outputs. 5. X = VIH or VIL. 6. NC = No change. 7. NA = Not applicable. 8. P = Positive going pulse. 9. N = Negative going pulse. FIGURE 3. Truth tables - Continued. 48 Carry H H H H Borrow H H H H H H N if count = 15 H if count 15 H H N if count = 0 H if count 0 MIL-M-38510/315D DEVICE TYPE 08 UP COUNT SEQUENCE TABLE QA (LSB) L H L H L H L H L H L H L H L H QB QC L L H H L L H H L L H H L L H H L L L L H H H H L L L L H H H H QD (MSB) L L L L L L L L H H H H H H H H DOWN COUNT SEQUENCE TABLE Carry QA (LSB) H L H L H L H L H L H L H L H L H H H H H H H H H H H H H H H L QB QC H H L L H H L L H H L L H H L L H H H H L L L L H H H H L L L L QD (MSB) H H H H H H H H L L L L L L L L DEVICE TYPES 09 AND 13 Mode select table Ripple carry truth table Inputs Inputs Mode Outputs RC output Load Enable G U/D H L L Count up L H L H Count down H X X H L X X X Preset (Asyn) X X L H H H X X No change (Hold) Enable G CLK L = Low voltage level H = High voltage level X = Don't care = Low-to-high clock transition = Negative going clock pulse NOTE: The up count and down count sequence for device type 09 is identical as that for device type 08. The up count and down count sequence for device type 13 is identical as that for device type 07. FIGURE 3. Truth tables - Continued. 49 CLK Max/Min H Borrow H H H H H H H H H H H H H H H L MIL-M-38510/315D FIGURE 4. Switching time test circuit and waveforms for device type 01. 50 MIL-M-38510/315D TEST F MAX A TO QC B TO QD SWITCH POSITION SW1 SW2 1 CLOSED 1 CLOSED 2 OPEN TEST CIRCUIT NOTES: 1. The pulse generator has the following characteristics: Vgen = 3 V, tr 15 ns, tf 6 ns, tp = .5 s, PRR 1 MHz, Zout 50. 2. All diodes are 1N3064 or equivalent. 3. CL includes probe and jig capacitance. 4. Voltage values are with respect to ground terminal. 5. FMAX: tr = tf 6 ns. FIGURE 4. Switching time test circuit and waveforms for device type 01 - Continued. 51 MIL-M-38510/315D VOLTAGE WAVEFORMS FIGURE 5. Switching time test circuit and waveforms for device type 02. 52 MIL-M-38510/315D TEST F MAX A TO QC B TO QD SWITCH POSITION SW1 SW2 1 CLOSED 1 CLOSED 2 OPEN TEST CIRCUIT NOTES: 1. The pulse generator has the following characteristics: Vgen = 3 V, tr 15 ns, tf 6 ns, tp = .5 s, PRR 1 MHz, Zout 50. 2. All diodes are 1N3064 or equivalent. 3. CL includes probe and jig capacitance. 4. Voltage values are with respect to ground terminal. 5. FMAX: tr = tf 6 ns. FIGURE 5. Switching time test circuit and waveforms for device type 02 - Continued. 53 MIL-M-38510/315D VOLTAGE WAVEFORMS FIGURE 6. Switching time test circuit and waveforms for device types 03, 04, 11, and 12. 54 MIL-M-38510/315D VOLTAGE WAVEFORMS FIGURE 6. Switching time test circuit and waveforms for device types 03, 04, 11, and 12 - Continued. 55 MIL-M-38510/315D NOTE: The clear pulse generator has the following characteristics: Vgen = 3.0 V, tr 15 ns, tf 6 ns, 20 ns tw(clear) 25 ns for types 11 and 12, 20 ns tsetup 25 ns, thold = 0 ns. FIGURE 6. Switching time test circuit and waveforms for device types 03, 04, 11, and 12 - Continued. 56 MIL-M-38510/315D NOTE: The data pulse generator has the following characteristics: Vgern = 3.0 V, tr 15 ns, tf 6 ns, tDATA = 30 ns, tsetup = 20 ns, tHOLD = 10 ns. FIGURE 6. Switching time test circuit and waveforms for device types 03, 04, 11, and 12 - Continued. 57 MIL-M-38510/315D NOTES: 1. The pulse generator has the following characteristics: Vgen = 3 V, tr 15 ns, tf 6 ns, tp = .5 s, PRR 1 MHz, Zout 50. 2. All diodes are 1N3064 or equivalent. 3. CL includes probe and jig capacitance. 4. Voltage values are with respect to ground terminal. 5. FMAX: tr = tf 6 ns. FIGURE 6. Switching time test circuit and waveforms for device type 03, 04, 11, and 12 - Continued. 58 MIL-M-38510/315D FIGURE 7. Switching time test circuit and waveforms for device types 05 and 06. 59 MIL-M-38510/315D FIGURE 7. Switching time test circuit and waveforms for device types 05 and 06 - Continued. 60 MIL-M-38510/315D NOTES: 1. The pulse generator has the following characteristics: Vgen = 3 V, tr 15 ns, tf 6 ns, tp = .5 s, PRR 1 MHz, Zout 50. 2. All diodes are 1N3064 or equivalent. 3. CL includes probe and jig capacitance. 4. Voltage values are with respect to ground terminal. 5. FMAX: tr = tf 6 ns. 6. The clear pulse generator has the following characteristics: Vgen = 3.0 V, tr 15 ns, tf 6 ns, tw(CLEAR) = 20 ns. FIGURE 7. Switching time test circuit and waveforms for device types 05 and 06 - Continued. 61 MIL-M-38510/315D FIGURE 8. Switching time test circuit and waveforms for device types 07. 62 MIL-M-38510/315D NOTES: 1. The pulse generator has the following characteristics: Vgen = 3 V, tp = .5 s, PRR 1 MHz, Zout 50, tr 15 ns, tf 6 ns between 0.7 V and 2.7 V. 2. All diodes are 1N3064 or equivalent. 3. CL includes probe and jig capacitance. 4. Voltage values are with respect to ground terminal. 5. FMAX: tr = tf 6 ns. 6. The clear pulse generator has the following characteristics: Vgen = 3.0 V, tr 15 ns, tf 6 ns, between 0.7 V and 2.7 V, tw(CLEAR) = 20 ns. FIGURE 8. Switching time test circuit and waveforms for device types 07 and Continued. 63 MIL-M-38510/315D FIGURE 9. Switching time test circuit and waveforms for device type 08. 64 MIL-M-38510/315D NOTES: 1. The load and count pulse generators have the following characteristics: Vgen = 3 V, tp = .5 s, PRR 1 MHz, Zout 50, tr 15 ns, tf 6 ns between 0.7 V and 2.7 V. 2. All diodes are 1N3064 or equivalent. 3. CL includes probe and jig capacitance. 4. Voltage values are with respect to ground terminal. 5. FMAX: tr = tf 6 ns. 6. The clear pulse generator has the following characteristics: Vgen = 3.0 V, tr 15 ns, tf 6 ns, between 0.7 V and 2.7 V, tw(CLEAR) = 20 ns. FIGURE 9. Switching time test circuit and waveforms for device type 08 - Continued. 65 MIL-M-38510/315D FIGURE 10. Switching time test circuit and waveforms for device type 09. 66 MIL-M-38510/315D TEST CIRCUIT NOTES: 1. The pulse generator has the following characteristics: Vgen = 3 V, tp = .5 s, PRR 1 MHz, Zout 50, tr 15 ns, tf 6 ns between 0.7 V and 2.7 V. 2. All diodes are 1N3064 or equivalent. 3. CL includes probe and jig capacitance. 4. Voltage values are with respect to ground terminal. 5. FMAX: tr = tf 6 ns. FIGURE 10. Switching time test circuit and waveforms for device type 09 - Continued. 67 MIL-M-38510/315D VOLTAGE WAVEFORMS FIGURE 11. Switching time test circuit and waveforms for device type 10. 68 MIL-M-38510/315D TEST F MAX A TO QC B TO QD SWITCH POSITION SW1 SW2 1 CLOSED 1 CLOSED 2 OPEN TEST CIRCUIT NOTES: 1. The pulse generator has the following characteristics: Vgen = 3 V, tr 15 ns, tf 6 ns, tp = .5 s, PRR 1 MHz, Zout 50. 2. All diodes are 1N3064 or equivalent. 3. CL includes probe and jig capacitance. 4. Voltage values are with respect to ground terminal. 5. FMAX: tr = tf 6 ns. FIGURE 11. Switching time test circuit and waveforms for device type 10 - Continued. 69 MIL-M-38510/315D FIGURE 12. Switching time test circuit and waveforms for device type 13. 70 MIL-M-38510/315D NOTES: 1. The pulse generator have the following characteristics: Vgen = 3 V, tp = .5 s, PRR 1 MHz, Zout 50, tr 15 ns, tf 6 ns, between 0.7 V and 2.7 V. 2. All diodes are 1N3064 or equivalent. 3. CL includes probe and jig capacitance. 4. Voltage values are with respect to ground terminal. 5. FMAX: tr = tf 6 ns. Figure 12. Switching time test circuit and waveforms for device type 13 - Continued. 71 TABLE III. Group A inspection for device type 01. Terminal conditions (pins not designated may be H 2.0 V; or L 0.7 V; or open). Subgroup MIL-STD883 Symbol method 1 VOL Tc = 25C VOH IIL1 3007 " " " " " 3006 " " " " " 3009 " " " 19 20 21 22 23 24 25 26 27 28 29 30 31 32 72 18 VIC IIH3 3010 " " " " " " " " IIH2 2 3 4 5 6 7 8 9 10 11 12 13 14 2 3 4 6 8 9 10 12 13 14 16 18 19 20 Measured B 2.0 V " " GND 2.0 V 2.0 V 2.0 V GND 2.0 V GND 3/ 4/ 3/ 5/ RO(1) 2.0 V " " " " 0.7 V 2.0 V 0.7 V " " 3/ 3/ 0.4 V 5.5 V RO(2) 2.0 V " " " 0.7 V 2.0 V 0.7 V 2.0 V 0.7 V 0.7 V 3/ 3/ 5.5 V 0.4 V NC VCC 4.5 V " " " " " " " " " " " 5.5 V " " " R9(1) GND GND 2.0 V 0.7 V 2.0 V " " " " " 0.7 V 0.7 V R9(2) GND GND 0.7 V 2.0 V " " " " " " 0.7 V 0.7 V QC 4mA QB QD QA NC A GND " " 2.0 V GND " " 2.0 V GND 2.0 V GND GND terminal QC QB QD QA QC QB QD QA QD QA QC QB RO(1) RO(2) R9(1) R9(2) Min 2.5 " " " " " 6/ " " " 6/ " " " V " " " " " " " " " " " mA " " " " " 17 IIL3 IIH1 1 GND 0.4 V GND GND GND -18 mA -18 mA -18 mA 2.7 V 2.7 V 5.5 V 5.5 V Limits Unit " 0.4 V 5.5 V 3/ 5.5 V 0.4 V 3/ GND GND " " " " " " " " " " " " " " " " A " " 3/ 3/ " B " " " 4.5 V " " " " " 5.5 V " " " " " " " -18 mA " " " " " " " " " " " " " " R9(1) R9(2) A B RO(1) RO(2) R9(1) R9(2) RO(1) RO(2) R9(1) R9(2) RO(1) RO(2) -1.5 " " " " " 20 " " " 100 " " " V " " " " " A " " " " " " " -18 mA 2.7 V 2.7 V 5.5 V 5.5 V 4 mA 4 mA 4 mA -0.4 mA -0.4 mA 4 mA 2/ -0.4 mA -0.4 mA -0.4 mA -0.4 mA 0.4 V -18 mA Max 0.4 " " " " " 33 " " 2.7 V A 80 " IIH4 " 34 " " 5.5 V A 400 " IIH5 " 35 2.7 V " " B 160 " IIH6 " 36 5.5 V " " B 800 " See footnotes at end of device types 01. MIL-M-38510/306E IIL2 Cases A,B,C,D Cases1/ 2 Test no. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Subgroup 1 Tc = 25C Symbol IOS MIL-STD883 method 3011 " " " ICC Cases A,B,C,D Cases 1/ 2 Test no. 37 38 39 40 41 1 2 TABLE III. Group A inspection for device type 01 - Continued Terminal conditions (pins not designated may be H 2.0 V or L 0.7 V or open). 3 4 5 6 7 8 9 10 3 4 6 8 9 10 12 13 14 16 18 19 20 NC VCC 5.5 V " " " R9(1) 5.5 V 5.5 V GND " R9(2) 5.5 V 5.5 V GND " QC QB GND GND " " " QD GND QA NC A 3/ 5/ 3/ 4/ RO(2) GND GND 3/ " GND " " " " " Same tests, terminal conditions, and limits as for subgroup 1, except TC = -55C and VIC tests are omitted. A 8/ B B A B B A B A B A B A B A B A B A B B A B A B A B A B A B B A B A B A B B B A B A B A 8/ " " B B A A A A A B B " " " " " " " " " " A " " " " " " " " B B A " " " " " B " " " " A 8/ " " B B A " " " " " " " " " " " " " " B " " " " " " " " " " " " " " " " " A " " " " " 4.5 V " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A A B A A B " " " " " " " " " " " " " " " A " " " " " " " " " B " " " " " " " A " " " " A A B A A B B A " " " " " " " " " " " " B " " " " " " " " " " " " A " " " " B " " " " " " L " " " " " " " " " " " " H " " " L " " " " " " H " " " L " " " " " " H " " L " " " " H L " " " " " " " " " " H H L L H H L " " " " H H L L H H L " " " " H H L L H L " " H H L GND " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " GND " QD QA QB QC " VCC GND H H L H H L " " " " " " " " " " " H H L " " " " " " " " H H L " " " " " " " " " " " " " H H L H H L " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B 8/ " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " Unit Measured terminal See 9/ Min -15 " " " Max -100 " " " mA " " " 15 " MIL-M-38510/315D 73 See footnotes at end of device type 01. 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 GND GND Limits 14 RO(1) GND GND 3/ " 3 3014 " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " 13 2 Same tests, terminal conditions, and limits as for subgroup 1, except TC = 125C and VIC tests are omitted. Functional tests 7/ 12 B 2 7 TC = +25C 11 Subgroup 7 TC = +25C Symbol Functional tests 7/ 9 TC = +25C 10 TC = +125C 11 1 2 11 12 13 Limits 14 2 3 4 6 8 9 10 12 13 14 16 18 19 20 B A 8/ B A " " B A B A B A B A B B A B A B A B A A B B A A B " " " " " " " " " " " " RO(1) B 8/ " " " A A B " " " " " " A B " " " " " " " " " " " A A B " " " " A A B " " A A RO(2) A A B B A A B " " " " " " A B " " " " " " " " " " " A A B " " " A A B " " " " A NC VCC 4.5 V " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " R9(1) A " " " B " " " " " " " " " " " " " " " " " A A B " " " " " " " " " " " " A " " R9(2) B B A B " " " " " " " " " " " " " " " " " " A A B " " " " " " " " " " A " " B A QC H H L " " " " " " H " " " L " " " " H " " " L " " " " " " " " " " " " " " " " " QB L H L " " " " H H L L H H L " " H H L L H H L " " " " " " " " " " " " " " " " " GND GND " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " QD L L H H L " " " " " " " " " " " " " " " " " H " " " L " " " " " " " " " " H " " QA L L H H L " " " " " " " " " " " " " " " " " H " " " L " " H H L " " " H " " " " NC A B " " " " " " " " " " " " " " " " " " " " " " " " " " " A B A B A B A B A B A B Unit Measured terminal Min Max See 9/ MIL-M-38510/315D 74 8 MIL-STD883 method 3014 " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " Cases A,B,C,D Cases 1/ 2 Test no. 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 TABLE III. Group A inspection for device type 01 - Continued Terminal conditions (pins not designated may be H 2.0 V or L 0.7 V or open). 3 4 5 6 7 8 9 10 Same tests, terminal conditions, and limits as for subgroup 7, except TC = 125C and -55C. 3003 (Fig. 4) " " " " " 126 GND tPLH1 tPHL1 tPLH2 tPHL2 FMAX 127 128 129 130 131 11/ GND 11/ GND GND A 8/ tPLH1 tPHL1 tPLH2 tPHL2 " " " " 132 133 134 135 11/ GND 11/ GND A FMAX IN IN IN IN A A Same tests, terminal conditions, and limits as for subgroup 10, except TC = -55C. See footnotes at end of device type 01. 5.0 V GND " " " " " " " " " " OUT OUT GND " " " " " " " " OUT OUT " " " " " " " " " OUT IN 10/ A to QA 29 IN IN A to QC A to QC B to QD B to QD A to QA 3 " " " 29 53 58 37 40 ns " " " MHz A A B B 3 " " " 74 81 52 56 ns " " " OUT OUT OUT IN 10/ IN IN OUT OUT to QC to QC to QD to QD MHz 1/ Case 2 pins not referenced are N/C. 2/ Test 4, Pin 12; 4 mA + IIL3(MAX). 3/ Apply 4.5 V pulse then ground prior to taking measurements to set device in the desired state. 4/ Apply two pulses after RO (reset) pulse. 5/ Apply one pulse after RO (reset) pulse. 6/ IIL limits (mA) min/max values for circuits shown: Parameter IIL1 Terminals Circuits A B RO(1) -12/-.36 RO(2) " C D E F -.03/-.40 -.03/-.40 -12/-.36 -12/-.36 " " " " " " " " R9(2) " " " " " IIL2 A -0.5/-2.0 -1.0/-2.4 -1.0/-2.4 -1.0/-2.4 -0.5/-2.0 IIL3 B -0.4/-1.6 -1.3/-3.2 -1.3/-3.2 -1.3/-3.2 -1.0/-2.4 75 7/ Only a summary of attributes data is required. 8/ A = 3.0 V minimum, B = 0.0 V or GND. 9/ H > 1.5 V; L < 1.5 V. 10/ FMAX minimum limit specified is the frequency of the input pulse. The output pulse shall be one-half of the input frequency. 11/ Momentary 3.0 V (min), then ground. Maintain ground for measurement. MIL-M-38510/315D R9(1) " G TABLE III. Group A inspection for device type 02. Terminal conditions (pins not designated may be H 2.0 V; or L 0.7 V; or open). Subgroup 1 Tc = 25C 3009 " IIL2 " 15 IIL3 " 16 IIH1 IIH1 IIH2 IIH2 3010 " " " Symbol MIL-STD883 method VOL 3007 " " " VOH 3006 " " " VIC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 2 3 4 6 8 9 10 12 13 14 16 18 19 20 B GND 2.0 V " " GND 3/ 4/ 3/ 5/ 3/ 6/ RO(1) 2.0 V " " " 3/ 3/ " " RO(2) 2.0 V " " " 3/ " " " NC VCC 4.5 V " " " " " " " " " " " 5.5 V " NC NC QC QB GND GND " " " " " " " " " " " " " QD QA 2/ NC A 2.0 V GND " " 3/ 4/ GND " " -18 mA -18 mA -18 mA 4 mA 4mA -0.4 mA -0.4 mA 4 mA -0.4 mA -0.4 mA Limits Min QA QB QC QD QA QB QC QD A B RO(1) RO(2) RO(1) RO(2) 2.5 " " " V " " " " " " " " " " " mA " 7/ " A " " " B " " " 20 20 100 100 A " " " -18 mA 5.5 V 0.4 V 3/ " " 3/ 3/ " " 17 18 19 20 2.7 V GND 5.5 V GND GND 2.7 V GND 5.5 V " " " " " " " " RO(1) RO(2) R0(1) R0(2) 0.4 V Max 0.4 " " " -1.5 mA " " " 7/ " 0.4 V 5.5 V 3/ 0.4 V Unit Measured terminal 76 IIH3 " 21 5.5 V " " " 2.7 V A 80 " IIH4 " 22 " " " " 5.5 V A 400 " " IIH5 " 23 2.7 V " " " B 80 " IIH6 " 24 5.5 V " " " " B 400 " IOS 3011 " " " 25 26 27 28 GND 3/ 4/ 3/ 5/ 3/ 6/ 3/ " " " 3/ " " " " " " " -100 " " " mA " " " 3005 29 GND 15 " ICC GND GND " 2 Same tests, terminal conditions, and limits as for subgroup 1, except TC = 125C and VIC tests are omitted. 3 Same tests, terminal conditions, and limits as for subgroup 1, except TC = -55C and VIC tests are omitted. See footnotes at end of device types 02. " " " " " GND GND 3/ 4/ GND " " QA QB QC QD VCC -15 " " " MIL-M-38510/315D IIL1 Cases A,B,C,D Cases1/ 2 Test no. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Subgroup 7 Tc = 25C Symbol Functional tests 8/ 9 TC = +25C 1 2 11 12 13 Limits 14 2 3 4 6 8 9 10 12 13 14 16 18 19 20 B B 9/ A B B A B " " A A B A B A B A B A B A B A B A B A B A B A B A B A B B A B A B A A B " " " " RO(1) A 9/ " " " " " " B " " " " " " " " " " " " " " " " " " " " " " " " " " " A " " " " " " " B " " " RO(2) A " " B " " A " " B " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A A B " " " NC VCC 4.5 V " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " NC NC QC L " " " " " " " " " " " H " " " L " " " H " " " L " " " H " " " L " " " " H " " " L " " " " " QB L " " " " H L " " " H H L L H H L L H H L L H H L L H H L L H H L L H " " L L H H L " " " " " GND GND " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " QD L " " " " " " " " " " " " " " " H " " " " " " " L " " " " " " " H " " " " " " " " L " " " " " QA L " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " H H L NC A B 9/ " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A B A B Unit Measured terminal Min Max See 10/ MIL-M-38510/315D 77 8 MIL-STD883 method 3014 " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " Cases A,B,C,D Cases 1/ 2 Test no. 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 TABLE III. Group A inspection for device type 02 - Continued Terminal conditions (pins not designated may be H 2.0 V or L 0.7 V or open). 3 4 5 6 7 8 9 10 Same tests, terminal conditions, and limits as for subgroup 7, except TC = +125C and -55C. FMAX tPLH1 tPHL1 tPLH2 tPHL1 3003 (Fig. 5) " " " " See footnotes at end of device type 02. 77 78 79 80 81 GND IN IN 12/ GND 12/ GND 5.0 V A 9/ A " " " " GND OUT OUT " " " " OUT OUT OUT IN 11/ A to QA 29 IN IN A to QC A to QC B to QD B to QD 3 " " " MHz 53 58 56 56 ns " " " Subgroup Symbol 10 TC = +125C FMAX tPLH1 tPHL1 tPLH2 tPHL2 11 MIL-STD883 method 3003 (Fig. 5) " " " " Cases A,B,C,D Cases 1/ 2 Test no. 82 1 83 84 85 86 TABLE III. Group A inspection for device type 02 - Continued Terminal conditions (pins not designated may be H 2.0 V or L 0.7 V or open). 2 3 4 5 6 7 8 9 10 11 12 13 14 Limits 2 3 4 6 8 9 10 12 13 14 16 18 19 20 Measured terminal B RO(1) GND RO(2) NC VCC 5.0 V NC NC QC QB GND GND QD QA OUT NC A IN 11/ Min 29 Max A to QA 12/ GND 12/ GND A A to QC A to QC B to QD B to QD 3 " " " 74 81 78 78 IN IN " " " " A OUT OUT " " " " IN IN OUT OUT Unit MHz ns " " " Same tests, terminal conditions, and limits as for subgroup 10 except, TC = 55C Case 2 pins not referenced are N/C. 2/ For test 1, 4 mA +IIL3 (max). 3/ Apply 4.5 V pulse, then ground prior to taking measurements to set device in the desired state. Maintain ground for measurement. 4/ Input pulse must be applied one time after RO pulse. 5/ Input pulse must be applied twice after RO pulse. 6/ Input pulse must be applied four times after RO pulse. 7/ IIL limits (mA) min/max values for circuits shown: Parameter Terminals IIL1 RO(1) MIL-M-38510/315D 78 1/ Circuits A B C D E F -12/-.36 -.03/-.40 -12/-.36 -.03/-.40 -12/-.36 -12/-.36 RO(2) " " " " " " IIL2 A -0.5/-2.0 -1.0/-2.4 -0.5/-2.0 -1.0/-2.4 -1.0/-2.4 -0.5/-2.0 IIL3 B -0.4/-1.6 -0.4/-1.6 -0.4/-1.6 -0.4/-1.6 -.65/-1.6 -0.4/-1.6 8/ Only a summary of attributes data is required. 9/ A = 3.0 V minimum; B = 0.0 V or GND. 10/ H > 1.5 V; L < 1.5 V. 11/ FMAX min limit specified is the frequency of the input pulse. The output frequency shall be one-half the input frequency. 12/ Momentary 3.0 V (min), then ground. Maintain ground for measurement. G Subgroup Symbol 1 VOL Tc = +25C VOH MIL-STD883 method Cases E, F Cases1/ 2 2 3 Clear Clock 1 2 3 4 5 4.5 V " " " " 2/ " " " 3006 " " " " 6 7 8 9 10 " " " " " 2/ " " " " 11 12 13 14 15 16 17 18 19 -18 mA 20 0.4 V 3009 IIL6 " 21 IIL4 IIL5 IIL5 " " " " " " " 22 23 24 25 26 27 28 5/ IIH13 3010 29 13/ IIH9 " 30 IIH11 " " " " " " " 31 32 33 34 35 36 37 79 IIL4 3 4 A TABLE III. Group A inspection for device types 03, 04, 11, and 12. Terminal conditions (pins not designated may be H 2.0 V; or L 0.7 V; or open). 4 5 6 7 8 9 10 11 12 5 7 8 9 10 12 13 14 15 B C D EnP 0.7 V 0.7 V 0.7 V 0.7 V 2.0 V 2.0 V 2.0 V 2.0 V 2.0 V 3/ 3/ 2.0 V -18 mA -18 mA -18 mA -18 mA -18 mA -18 mA Load GND " " " " GND " " " " " " " " " GND " " " " EnT 0.4 V 0.4 V 0.4 V 0.4 V 4.5 V 4.5 V 2.7 V 2.7 V 2.7 V 2.7 V 2.7 V 2.7 V 2.7 V GND GND QC QB 15 19 QA Ripple carry 16 20 Limits Measured terminal " " " " " " " " " QD QC QB QA Ripple carry QD QC QB QA Ripple carry Clear Clock A B C D EnP Load EnT 5.5 V Clear " Clock " " " " " " " " A B C D EnP Load EnT " " " " " " " " " " " " " " " " A B C D EnP Load EnT " " " " " " " " " " " " " " " " " -.4 mA -.4 mA -.4 mA -.4 mA 2.0 V -18 mA GND 2.7 V GND -.4 mA " " " " " 4 mA -18 mA GND " " " 4.5 V 0.4 V 4.5 V 4 mA 4 mA 0.7 V 4.5 V 4.5 V 0.4 V GND GND 2.7 V Unit Min VCC 4.5 V " " " " 4 mA " 0.4 V QD 14 18 4 mA " 0.4 V See footnotes at end of device types 03, 04, 11, and 12. GND 13 17 Max 0.4 " " " " 2.5 " " " " V " " " " " " " " " -1.5 " " " " " " " " " " " " " " " " " 4/ A " " " " " " " " " " " " " " " " " " " " " " " " Clear 20 " Clock 40 " 20 " " " " 40 40 " " " " " " " 4/ MIL-M-38510/315D Test no. 3007 " " " " VIC IIH9 IIH9 1 2 Subgroup 1 Symbol IIH14 Tc = +25C IIH10 IIH12 IIH10 IIH10 IOS 1 2 2 3 3 4 Test no. Clear Clock A B 3010 38 13/ 5.5 V " 39 " " " " " " " 3011 " " " " 40 41 42 43 44 45 46 47 48 49 50 51 4.5 V " " " " 2/ " " " " 4.5 V 4.5 V 6/ 6/ 4.5 V 3005 " " " 52 53 54 55 5.5 V 5.5 V GND GND 5.5 V 5.5 V GND GND 5.5 V 5.5 V GND GND 5.5 V 5.5 V GND GND 5.5 V 5.5 V GND GND 5.5 V 5.5 V GND GND MIL-STD883 method C D EnP 5.5 V 5.5 V 5.5 V 5.5 V 5.5 V 5.5 V GND GND 4.5 V 4.5 V 4.5 V 5.5 V 5.5 V GND GND GND Load QD QC 14 18 15 19 16 20 QB QA Ripple carry VCC Limits Unit Measured terminal Min Max 5.5 V Clear " " Clock 200 " " " " " " " " " " " " " GND 5.5 V GND GND " " " " 4.5 V " " " " " " " " " " " " 100 " " " " 200 200 -100 " " " " " " " " " " " mA " " " " " " " " 5.5 V GND GND GND 5.5 V 5.5 V GND GND A B C D EnP Load EnT QD QC QB QA Ripple carry VCC " " " 31 31 32 32 " " " " Same tests, terminal conditions, and limits as for subgroup 1, except TC = 125C and VIC tests are omitted. 3 Same tests, terminal conditions, and limits as for subgroup 1, except TC = -55C and VIC tests are omitted. GND GND 5.5 V GND GND GND GND GND " " " " 100 A GND 2 80 See footnotes at end of device types 03, 04, 11, and 12. EnT 13 17 -15 " " " " MIL-M-38510/315D ICCH ICCH ICCL ICCL Cases E, F Cases1/ 2 TABLE III. Group A inspection for device types 03, 04, 11, and 12 - Continued. Terminal conditions (pins not designated may be H 2.0 V; or L 0.7 V; or open). 4 5 6 7 8 9 10 11 12 5 7 8 9 10 12 13 14 15 Subgroup 7 Tc = +25C Symbol Functional tests 7/ Cases E, F Cases 1/ 2 Test no. 3014 " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 1 2 2 3 3 4 Clear Clock A B C D EnP GND Load EnT A 8/ B A A B A A B A A B A A B A A B A A B A A B A A B A A B A " " " " " B A " " " " " " " " " " " " " " " " " " " " " " A 8/ B A A B A A B A A B A A B A A B A A B A A B A A B A A B A " " " " " B A A A B B B A " " " " " B " " " " " A " " " " A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A " " " " " B A A A B B B A " " " " " B " " " " " A " " " " A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A " " " " " B A A A B " " " " " " " " A " " " " " " " " " " A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B " " A " " " " " " " " " " " " " " " " " " " " " " " GND " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B " " " " " A " " B " " A " " B " " " A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A " " " " " B " " " " " " " " " " " " " " " " " " A " " " " B 8/ A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B A " " " " " " " " " " " " " " " " " " " " " B A A A B A 8/ A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A A B A A A B A A B A A B A A B A A B A A B A A A B A A 12 15 13 17 14 18 15 19 16 20 QD QC QB QA VCC L " " " " " " " " " " " " " " " " " " " " " " " H " " " " " L " " " " " " " " " " " " " " " " " " " H " " " L " " H L L " " " " " " " " " " " H " " " " " " " " " " " L " " " " " " " " " " " " " " " " " " " H " " " " " L " " " " " " H L L " " " " " H " " " " " L " " " " " H " " " " " L " " " " " " " " " " " " " " " " " " " H " " " " " L " " " " " " H L L " " H " " L " " H " " L " " H " " L " " H " " L " " H " " L " " " " " " " " " " H " " " " " " " " " " " " L " " H L Ripple carry L " " " " " " " " " " " " " " " " " " " " " " " " " " H L H L " " " " " " " " " " " " " " " " " " " " " " " " " " X L 4.5 V " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " Measured terminal Limits Min Unit Max See 9/ MIL-M-38510/315D 81 MIL-STD883 method TABLE III. Group A inspection for device type 03 - Continued. Terminal conditions (pins not designated may be H 2.0 V or L 0.7 V or open). 4 5 6 7 8 9 10 11 5 7 8 9 10 12 13 14 See footnotes at end of device types 03, 04, 11, and 12. Subgroup 7 Tc = +25C Functional tests 7/ MIL-STD883 method Cases E, F Cases 1/ 2 Test no. 3014 " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 1 2 2 3 3 4 Clear Clock A B C D EnP GND Load EnT A 8/ " " B " " " " " " " " " " " A " " " " " B " " A " " B " " A " " B " " B 8/ " " " " " A " " B " " A " " B " " A " " " " " " " " B " " " " " A " " B " " " " " " " " A " " " " " B " " A " " B " " " " " A " " " " " " " " B " " A " " B " " A " " " " " " " " B " " A " " B " " " " " " " " " " " B " " A " " B " " " " " " " " A " " B " " A " " " " " " " " " " " " " " GND " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B " " A " " " " " " " " B " " A " " B " " " " " A " " " " " " " " " " " A 8/ " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " Repeat subgroup 7 at TC = +125C and TC = -55C. See footnotes at end of device types 03, 04, 11, and 12. A 8/ B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A 12 15 13 17 14 18 15 19 16 20 QD QC QB QA VCC L " " " " H " " L " " H " " " " " " " " L " " H " " L " " " " " " " " " L " " " " " " " " " " H " " " " " L " " H " " L " " " " " H " " " " " " L " " " " " " " H " " L " " H " " L " " H " " " " " " " " L " " " " " H L L H " " L " " " " " " " " " " " H " " " " " L " " H " " L " " H " " L Ripple carry L " " " " " " " " " " " " " " " " H L " " " " " " " " " " " " " " " " " 4.5 V " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " Measured terminal Limits Min Unit Max See 9/ MIL-M-38510/315D 82 8 Symbol TABLE III. Group A inspection for device type 03 - Continued. Terminal conditions (pins not designated may be H 2.0 V or L 0.7 V or open). 4 5 6 7 8 9 10 11 5 7 8 9 10 12 13 14 Subgroup 7 Tc = +25C Symbol Functional tests 7/ Cases E, F Cases 1/ 2 Test no. 3014 " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 1 2 2 3 Clear Clock B 8/ A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B A " " " " " " " " A 8/ A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A A B A B A B A A B 3 4 A B C D A 8/ B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A A A " " " " " " " " A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A A A " " B " " " A A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A A A " " B " " " A A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A A A " " B " " " " " EnP A 8/ " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B B A " " " " " " 12 15 13 17 14 18 15 19 16 20 Ripple carry L " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " H L H L " " " " " " " " " " 4.5 V " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " GND Load EnT QD QC QB QA GND " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B " " " A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A A A B " " " " " " " L " " " " " " " " " " " " " " " " " " " " " " " H " " " " " " " " " " " " " " " " " " " " " " " L " " " " " " " " " " L " " " " " " " " " " " H " " " " " " " " " " " L " " " " " " " " " " " H " " " " " " " " " " " L " " " " " " " " " " L " " " " " H " " " " " L " " " " " H " " " " " L " " " " " H " " " " " L " " " " " H " " " " " L " " " " " " " " " " L " " H " " L " " H " " L " " H " " L " " H " " L " " H " " L " " H " " L " " H " " L " " H " " L " " " " " " " H " " Measured terminal Limits Min VCC Unit Max See 9/ MIL-M-38510/315D 83 MIL-STD883 method TABLE III. Group A inspection for device type 04 - Continued. Terminal conditions (pins not designated may be H 2.0 V or L 0.7 V or open). 4 5 6 7 8 9 10 11 5 7 8 9 10 12 13 14 See footnotes at end of device types 03, 04, 11, and 12. Subgroup 7 Tc = +25C Functional tests 7/ MIL-STD883 method Cases E, F Cases 1/ 2 Test no. 3014 " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 1 2 2 3 Clear Clock A 8/ " " " " " B A " " " B A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " Repeat subgroup 7 at TC = +125 and TC = -55C. See footnotes at end of device types 03, 04, 11, and 12. A 8/ A B A B A A A B A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A 3 4 12 15 13 17 14 18 15 19 16 20 Ripple carry L " " " " " " " " H " L " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " 4.5 V " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A B C D EnP GND Load EnT QD QC QB QA A " " " " " " " " " " " B " " " " " A " " B " " A " " B " " " " " A " " B " " A " " A " " " B B A " " " " " " " " " " " " " " B " " " " " A " " B " " A " " B " " " " " A " " " B B A " " " " " " " " B " " " " " A " " " " " " " " B " " " " " A " " " " " B " " " A " " " " " " " " " " B " " " " " " " " " " " " " " A " " " " " " " " " " " A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " GND " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B A " " B " " " " " " A B " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B " " " " " A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " L " " " " H L " " H " L " " H " " L " " " " " " " " " " " " " " H " " " " " " " " " H " " " " L " " " H " L " " H " " L " " " " " H " " " " " " " " L " " " " " H " " " H " " " " L " " " H " L " " H " " " " " " " " L " " " " " H " " L " " H " " L " " " H " " " " " L " " H " L " " " " " " " " H " " L " " H " " L " " " " " H " " L " " H Measured terminal Limits Min VCC Unit Max See 9/ MIL-M-38510/315D 84 8 Symbol TABLE III. Group A inspection for device type 04 - Continued. Terminal conditions (pins not designated may be H 2.0 V or L 0.7 V or open). 4 5 6 7 8 9 10 11 5 7 8 9 10 12 13 14 Subgroup 7 Tc = +25C Symbol Functional tests 7/ MIL-STD883 3014 " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 See footnotes at end of device types 03, 04, 11, and 12. 1 2 2 3 3 4 Clear Clock A B C D B 8/ " " " A A A B A A B A A B A A B A A B A A B A A B A A B A A B B A A B A " " " " " " " " " " " " " " " " " " " " " " B " " " A A A B A A B A A B A A B A A B A A B A A B A A B A A B B A A B A " " " " " B " " A " " " " " B " " " " A " " B " " " A A A B A A B A A B A A B A A B A A B A A B A A B A A B B A A B A " " " " " B " " A " " " " " B " " " " A " " B 8/ " " " A A A B A A B A A B A A B A A B A A B A A B A A B A A B B A A B A " " " " " B " " " " " " " " A " " " " " " " B 8/ B A A B B B A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A " " " " " B B A B 8/ A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B B A A B A A B A B A B A A B A A B A B A A B A B A A EnP A 8/ " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B " " A " " " " " " " " A " " " " " " " " 12 15 13 17 14 18 15 19 16 20 Ripple carry X L " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " H L H L " " " " " " " " " " " " " " " " " " H L L 4.5 V " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " GND Load EnT QD QC QB QA GND " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B " " " A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B " " " " A " " B B A " " " " B A " " " " " " B A A B A A B A A B A A B A A B A A B A A B A A B B A A B A A " " " B " " " " " " " " " " " " " " A " " X L " " " " " " " " " " " " " " " " " " " " " " " " " " " " H " " " " " " L " " " " " " " " " " " " " " H " " " " L L X L " " " " " " " " " " " " " " " " H " " " " " " " " " " " L " " " " " " " " " " " " " " " " H " " " " L " " " " " " X L " " " " " " " " " " H " " " " " L " " " " " H " " " " " L " " " " " " " " " " " " " " " " H " " " " L " " " " " " X L " " " " " " " H " " L " " H " " L " " H " " L " " H " " L " " " H " " L " " " " " " H " " " " " " " " " " " " L L Measured terminal VCC Limits Min Unit Max See 9/ MIL-M-38510/315D 85 method Cases E, F Cases 1/ 2 Test no. TABLE III. Group A inspection for device type 11 - Continued. Terminal conditions (pins not designated may be H 2.0 V or L 0.7 V or open). 4 5 6 7 8 9 10 11 5 7 8 9 10 12 13 14 Subgroup 7 Tc = +25C Functional tests 7/ MIL-STD883 method Cases E, F Cases 1/ 2 Test no. 3014 " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 1 2 2 3 3 4 Clear Clock A B C D EnP GND Load EnT A " " " " " B " " " " " " " " " " " A " " B " " A " " B " " " " " A " " " " " B " " " " " " A A B " " " " " A " " " " " B " " " " " A " " B " " " " " A " " B " " " " " " " " " " " " " " A " " B " " A " " " " " " " " B " " " " " A " " A " " " " " B " " A " " B " " A " " B " " " " " " " " " " " A " " " " " " " " A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " GND " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A " " A " " " " " B " " " " " A " " " " " " " " " " " " " " " " " " " " " " " " " " A 8/ " " " B B A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " Repeat subgroup 7 at TC = +125 and TC = -55C. See footnotes at end of device types 03, 04, 11, and 12. B 8/ A B A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A 12 15 13 17 14 18 15 19 16 20 QD QC QB QA VCC L H " " " L " " " " " H " " L " " H " " L " " " " " " " " " " " H " " " " " L L " " " " " " " " " " " " " " " " H " " L " " H " " " " " " " " L " " " " " " L " " " " " " " H " " L " " " " " H " " " " " L " " " " " H " " L " " " " " " L H " " " L " " " " " " " " " " " " " " H " " L " " H " " L " " " " " H " " L Ripple carry L H " " " L " " " " " " " " " " " " " " " " " " " " " " " " " " " " " H " " L 4.5 V " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " Measured terminal Limits Min Unit Max See 9/ MIL-M-38510/315D 86 8 Symbol TABLE III. Group A inspection for device type 11 - Continued. Terminal conditions (pins not designated may be H 2.0 V or L 0.7 V or open). 4 5 6 7 8 9 10 11 5 7 8 9 10 12 13 14 Subgroup 7 Tc = +25C Symbol Functional tests 7/ Cases E, F Cases 1/ 2 Test no. 3014 " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 See footnotes at end of device types 03, 04, 11, and 12. 1 2 2 3 Clear Clock B 8/ B A A B B B A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B 8/ A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A B A B A 3 4 A B C D B 8/ " " " A " " B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A " " " " " B " " " A " " B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A " " " " B B " " " A " " B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A " " " " B B " " " A " " B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A " " " " B EnP A 8/ " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B " A A 12 15 13 17 14 18 15 19 16 20 Ripple carry X L " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " H L H L " " " " 4.5 V " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " GND Load EnT QD QC QB QA GND " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B " " " A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A " " " " " " B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A B " " " X L " " " " " " " " " " " " " " " " " " " " " " " " " " " " H " " " " " " " " " " " " " " " " " " " " " " " L " " " " X L " " " " " " " " " " " " " " " " H " " " " " " " " " " " L " " " " " " " " " " " H " " " " " " " " " " " L " " " " X L " " " " " " " " " " H " " " " " L " " " " " H " " " " " L " " " " " H " " " " " L " " " " " H " " " " " L " " " " X L " " " " " " " H " " L " " H " " L " " H " " L " " H " " L " " H " " L " " H " " L " " H " " L " " H " " L " " " " Measured terminal VCC Limits Min Unit Max See 9/ MIL-M-38510/315D 87 MIL-STD883 method TABLE III. Group A inspection for device type 12 - Continued. Terminal conditions (pins not designated may be H 2.0 V or L 0.7 V or open). 4 5 6 7 8 9 10 11 5 7 8 9 10 12 13 14 Subgroup 7 Tc = +25C Functional tests 7/ MIL-STD883 method Cases E, F Cases 1/ 2 Test no. 3014 " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 1 2 2 3 Clear Clock A B C D EnP GND Load EnT B A A B A A B A B A A B A A B B A " " " " " " " B A A B A A B A A B A A B A A B A A B A A B A A B A A B A A " " " " " " " " " " " " B A A A B A B A B B A " " B " " A " " B " " " " " " " " A " " B " " A " " " " " B 8/ B A " " " " B " " A " " " " B " " " " " " A " " " B " " " " " A " " B " " A " " " " " B " " " " " " " " B 8/ B A " " " " B " " A " " " " B " " A " " " B " " " A " " " " " " " " B " " " " " " " " A " " " " " " " " B " " " " " " A " " " " " " " B " " A A B " " " " " " " " " " " " " " A " " " " " " " " " " " " " " " " " A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " GND " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B " " " " A " " B " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A " " B " " " " " " " " " A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A 8/ " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " Repeat subgroup 7 at TC = +125 and TC = -55C. See footnotes at end of device types 03, 04, 11, and 12. 3 4 12 15 13 17 14 18 15 19 16 20 QD QC QB QA L " " " " " " " " H " " " " " " L " " " " " " " " " " " " " " " " " " " " H " " " " " " " " " " " " " " " L " " " H " " " " L " " H " " " L " " " " " " " " " " " H " " " " " " " " L " " " " " " " " H " " " " " " L " " " H " " " " L " " H " " " L " " " " " " " " H " " L " " " " " H " " L " " H " " " " " L " " " " " H L H " " " " " " " " " " " " " " " " " " " " " " " " " " L " " H " " L " " " " " " " " H " " L " " H " " L Ripple carry L " " " " " " " " " " " H " " " L " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " 4.5 V " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " Measured terminal Limits Min VCC Unit Max See 9/ MIL-M-38510/315D 88 8 Symbol TABLE III. Group A inspection for device type 12 - Continued. Terminal conditions (pins not designated may be H 2.0 V or L 0.7 V or open). 4 5 6 7 8 9 10 11 5 7 8 9 10 12 13 14 Subgroup MIL-STD883 Symbol method 9 FMAX Tc = +125C 10/ 3003 (Fig 6) Cases E, F Case 1/ Test no. (Device types) 151 157 154 1 168 2 TABLE III. Group A inspection for device types 03, 04, 11, and 12. Terminal conditions (pins not designated may be H 2.0 V; or L 0.7 V; or open). 3 4 5 6 7 8 9 10 11 12 13 14 15 19 Ripple carry 2 3 4 5 7 8 9 10 12 13 14 15 17 18 Clear Clock A B C D EnP GND Load EnT QD QC QB QA 4.5 V IN 4.5 V GND 4.5 V 4.5 V OUT 16 20 Min 5.0 V QA 22 Clk to carry Clk to carry Clk to QA Clk to QB Clk to QC Clk to QD Clk to QA Clk to QB Clk to QC Clk to QD Clk to QA Clk to QA Clk to QB Clk to QB Clk to QC Clk to QC Clk to QD Clk to QD EnT to Cy EnT to Cy Clr to QA Clr to QB Clr to QC Clr to QD 3 40 ns " 40 " " 29 " " " " " " " " " " " 32 " " " " " " " " " " " 29 " " 32 " " 29 " " 32 " " 29 " " 32 " " 29 " " 32 " " 19 " " " " 19 11/ 33 " " " " " " " " " " 152 158 155 169 " " " " " " OUT " tPHL4 " 153 159 156 170 " " " " " " OUT " " " " tPLH5 tPHL5 " 154 160 157 171 " " " 155 161 158 172 " " " " " " " " " " " " 156 162 159 173 " " 157 163 160 174 " " " " " " " " " " " OUT " OUT " OUT " OUT " 158 164 161 175 " " 159 165 162 176 " " " " " " " 160 166 163 177 " " " " " " " " " " " IN " GND IN " " IN " " IN " " " OUT " " OUT " " 161 167 164 178 " " 162 168 165 179 " " " " tPHL6 " 163 169 166 180 " tPLH6 " 164 170 167 181 " tPHL6 " " 165 171 168 182 " " " IN " IN " " OUT " OUT " OUT " OUT OUT " OUT " OUT " OUT " tPLH6 " 166 172 169 183 " tPHL6 " 167 173 170 184 " " " IN " " OUT " IN " " OUT " tPLH6 " 168 174 171 185 " tPHL6 " 169 175 172 186 " " 187 " " " tPLH7 " 170 176 173 tPHL7 " 171 177 174 188 " tPHL8 " 172 178 175 189 IN 12/ tPHL8 " 173 179 176 190 " " tPHL8 " 174 180 177 191 " " tPHL8 " 175 181 178 See footnotes at end of device types 03, 04, 11, and 12. 192 " " 4.5 V 4.5 V 4.5 V 4.5 V 4.5 V 4.5 V " 4.5 V " 4.5 V " GND " " " " " " IN OUT IN OUT OUT OUT OUT OUT " Unit Max MHz " MIL-M-38510/315D tPLH6 89 Measured terminal VCC tPLH4 " Limits Subgroup Symbol MIL-STD883 method 10 FMAX Tc = +125C 10/ tPLH4 177 183 180 194 tPHL4 " 178 184 181 195 tPLH5 " 179 185 182 196 " 180 186 183 197 " 181 187 184 198 182 188 185 199 183 189 186 200 " 184 190 187 201 " 185 191 188 202 " 186 192 189 203 tPLH6 " 187 193 190 204 tPHL6 " 188 194 191 205 tPLH6 " 189 195 192 206 tPHL6 " 190 196 193 207 tPLH6 " 191 197 194 208 tPHL6 " 192 198 195 209 tPLH6 " 193 199 196 210 tPHL6 " 194 200 197 211 tPLH7 " 195 201 198 212 tPHL7 " 196 202 199 213 tPHL8 " 197 203 200 214 tPHL8 " 198 204 201 215 tPHL8 " 199 205 202 216 tPHL8 " 200 206 203 217 1 2 13 14 15 19 Ripple carry 2 3 4 5 7 8 9 10 12 13 14 15 17 18 Clear Clock A B C D EnP GND Load EnT QD QC QB QA 90 Same terminal conditions as for subgroup 9. Same tests, terminal conditions, and limits as for subgroup 10, except TC = -55C. See footnotes at end of device types 03, 04, 11, and 12. 12 16 20 VCC Limits Measured terminal Clk to QA Clk to Carry Clk to carry Clk to QA Clk to QB Clk to QC Clk to QD Clk to QA Clk to QB Clk to QC Clk to QD Clk to QA Clk to QA Clk to QB Clk to QB Clk to QC Clk to QC Clk to QD Clk to QD EnT to carry EnT to carry Clr to QA Clr to QB Clr to QC Clr to QD Unit Min Max 22 MHz 3 56 ns " 56 " " 41 " " " " " " " " " " " 45 " " " " " " " " " " " 42 " " 48 " " 42 " " 48 " " 42 " " 48 " " 42 " " 48 " " 28 " " 28 " " 46 " " 46 " " 46 " " 46 " MIL-M-38510/315D " " tPHL5 11 3003 (Fig 6) " Cases E, F Case 1/ Test no. (Device types) 03 04 11 12 176 182 179 193 TABLE III. Group A inspection for device types 03, 04, 11, and 12. Terminal conditions (pins not designated may be H 2.0 V; or L 0.7 V; or open). 3 4 5 6 7 8 9 10 11 1/ For case 2, pins not referenced are NC. 2/ Apply one pulse prior to measurement as follows: 2.5 V min/5.0 V max 2.5 V min/5.0 V max or 0 V .2 V 0 V .2 V 3/ Apply 0.7 V for types 03 and 11; apply 2.0 V for types 04 and 12. 4/ IIL limits (A) min/max values for circuits shown: Parameter IIL6 Clear 03 Clear 04 Clear 11 Clear 12 EnP A, B, C, D Load EnT Clock A B C D E F -160/-400 " " " " " -30/-300 " " " " " -120/-360 " -160/-400 " " " " " -120/-360 " " -0/-100 " -150/-450 -320/-800 -30/-300 -120/-360 -150/-380 -120/-360 -240/-720 -150/-380 -0/-100 -160/-400 -300/-760 -160/-400 -0/-100 -180/-420 -0/-100 -290/-630 -120/-360 -160/-400 -290/-630 -340/-860 -290/-630 -320/-800 -160/-400 91 5/ For types 03 and 11, set outputs to 9th count (QA = 1, QD = 1, QB and QC = 0) prior to measurement. th For types 04 and 12, set outputs to 15 count (QA, QB, QC and QD = 1) prior to measurement. 6/ Apply GND for types 03 and 11; apply 4.5 V for types 04 and 12. 7/ Only a summary of attributes data is required. 8/ A = 3.0 V minimum; B = 0.0 V or GND. 9/ H > 1.5 V; L < 1.5 V; X = don't care. 10/ The FMAX minimum limit specified is the frequency of the input pulse. The output frequency shall be one-half of the input frequency. For type 04, circuit C, 20 MHz minimum. 11/ The limit for circuit B shall be 23 ns. 12/ For types 03 and 04, apply one clock pulse prior to test. For types 11 and 12 apply one clock pulse prior to test and another pulse during test. 13/ IIH13 limit for types 11 and 12; 40 A maximum. IIH14 limit for types 11 and 12; 200 A maximum. G -16/-400 " " " " " -320/-800 -160/-400 MIL-M-38510/315D IIL5 Circuits Terminals Subgroup Symbol 1 VOL Tc = +25C VOH MIL-STD883 method IIL14 1 2 3 4 5 3006 " " " " 6 7 8 9 10 4.05 V 11 -18 mA 3009 " " " " 12 13 14 15 16 17 18 19 20 21 22 23 24 " " 25 26 " 27 IIL15 " 28 IIL17 3010 29 " " " " " " " 30 31 32 33 34 35 36 " 37 IIH19 U/ D See footnotes at end of device types 05 and 06. 4.5 V 0.7 V 0.7 V 2 3 3 4 CK A B C D EP GND L ET QD' 2/ " " " " 0.7 V " " " " 0.7 V " " " " 0.7 V " " " " 0.7 V " " " " 4.5 V " " " 0.7 V GND " " " " 0.7 V " " " " 4.5 V " " " 0.7 V 4 mA " " " " " 2.0 V " " " " 2.0 V " " " " 2.0 V " " " " 2.0 V " " " " " " " " " " " " " " " " " " " " " " " " -.4 mA -18 mA -18 mA -18 mA -18 mA -18 mA -18 mA 0.4 V 0.4 V 0.4 V 0.4 V 0.4 V 0.4 V 0.4 V 2.7 V 2.7 V 2.7 V 2.7 V 2.7 V 2.7 V 14 18 15 19 16 20 QB' QA' Ripple carry VCC terminal 4 mA 4.5 V " " " " -.4 mA " " " " " QD QC QB QA Ripple carry QD QC QB QA Ripple carry 4 mA 4 mA 4 mA -.4 mA -.4 mA -.4 mA " " " " " " " " " " " " " " " " " " " " " " " 5.5 V " " " " " " " -18 mA -18 mA GND " " " " " " 0.4 V " 2.7 V QC' 13 17 0.4 V " Limits Measured U/ D CK A B C D EP L ET A B C D U/ D CK L 0.4 " " " " 2.5 " " " " V " " " " " " " " " -1.5 " 3/ " " " " " " " " 3/ 3/ 3/ " " " " " " " " A " " " " " " 3/ " ET 3/ 3/ " 20 " " " " " " " " " " " " " " " 40 " " " " " " " " " " " " " " " U/ D CK A B C D EP L " ET 2.7 V Max 3/ " 2.7 V Min EP " " Unit MIL-M-38510/315D 92 IIL13 Test no. 1 2 3007 " " " " VIC IIL12 Cases E, F Case 1/ 2 TABLE III. Group A inspection for device types 05 and 06. Terminal conditions (pins not designated may be H 2.0 V; or L 0.7 V; or open). 4 5 6 7 8 9 10 11 12 5 7 8 9 10 12 13 14 15 Subgroup Symbol MIL-STD883 method Cases E, F Cases1/ 2 Test no. 1 IIH18 1 2 U/ D 2 3 3 4 TABLE III. Group A inspection for device types 05 and 06. Terminal conditions (pins not designated may be H 2.0 V; or L 0.7 V; or open). 4 5 6 7 8 9 10 11 12 5 7 8 9 10 12 13 14 15 CK A B C D EP L ET 38 " " " " " " " 39 40 41 42 43 44 45 IIL20 " 46 I0S 3011 " " " " 47 48 49 50 51 5.5 V " " " " 2/ " " " " 5.5 V " " " " 5.5 V " " " " 5.5 V " " " " 5.5 V " " " " 5.5 V " " " " " " " " " GND " " " " 5.5 V " " " " 3005 52 GND " GND GND GND GND GND " 5.5 V GND ICC 5.5 V 5.5 V 5.5 V 5.5 V 5.5 V 5.5 V QC 15 19 16 20 QB QA Ripple carry VCC Limits Measured terminal GND 5.5 V " " " " " " " " " " " " " " U/ D CK A B C D EP L 5.5 V " 5.5 V 2 Same tests, terminal conditions, and limits as for subgroup 1, except TC = +125C and VIC tests are omitted. 3 Same tests, terminal conditions, and limits as for subgroup 1, except TC = -55C and VIC tests are omitted. 93 See footnotes at end of device types 05 and 06. QD 14 18 GND GND GND GND GND " ET " " " " " QD QC QB QA Ripple carry " VCC Unit Min -15 " " " " Max 100 A " " " " " " " " " " " " " " 200 " -100 " " " " " " " " " 34 " MIL-M-38510/315D 3010 Tc = +25C 5.5 V GND 13 17 Subgroup 7 Tc = +25C Functional tests 4/ MIL-STD883 method Cases E, F Cases 1/ 2 Test no. 3014 " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 1 2 U/ D A 5/ " " " " " " " " " " " " " " " " " " " " " " " " " " " " B " " " " " " " " " " " " " " " " " " " " " " " " " Repeat subgroup 7 at TC = +125 and TC = -55C. See footnotes at end of device types 05 and 06. 2 3 CK B 5/ A B A B A B A B A B A B A B A B A B A B A B A A B A B A B A B A B A B A B A B A B A B A B A B A B B A B B A 3 4 A B C D EP GND L ET B " " " " " " " " " " " " " " " " " " " " " " " " " " A " " " " " " " " " " " " " " " " " " " " " " " " " B B B " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A A B " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A A B " " " " " " " " " " " " " " " " " " " " " " " " " " A " " " " " " " " " " " " " " " " " " " " " " " " " " " B " " " " " " " " " " " " " " " " " " " A A B " " " " " " " " " " " " " " " " " " " " " " " " A A B " " " " " GND " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B B A " " " " " " " " " " " " " " " " " " " " " " " " B B A " " " " " " " " " " " " " " " " " " " " " " " B B B " " " " " " " " " " " " " " " " " " " " " " A A B " " " " " " " " " " " " " " " " " " " " " " " " A A B " " 12 15 13 17 14 18 15 19 16 20 QD QC QB QA X L 5/ " " " " " " " " " " " " " " " H " " " " " " " " L L H " " " L " " " " " " " " " " " " " " " " " " " " " " X L " " " " " " " H " " " " " " " L " " " " " " " " " " " " " " H " " " " " " " L " " " " " " " " " " " " " " X L " " " H " " " L " " " H " " " L " " " " " " " " " " " " " " H " " H L " " " H " " " L " " " " " " " " " H X L L H H L L H H L L H H L L H H L L H " " " " " " L L H H L L H H L L H " L L H H L L H H L " " " " " " " H Ripple carry X H 5/ " " " " " " " " " " " " " " " " " L L " " H H L H " L H " " " " " " " " " " " " " " " " L " " " H H L L H 4.5 V " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " Measured terminal VCC Limits Min Unit Max See 6/ MIL-M-38510/315D 94 8 Symbol TABLE III. Group A inspection for device type 05 - Continued. Terminal conditions (pins not designated may be H 2.0 V or L 0.7 V or open). 4 5 6 7 8 9 10 11 5 7 8 9 10 12 13 14 Subgroup 7 Tc = +25C Symbol Functional tests 4/ Cases E, F Cases 1/ 2 Test no. 3014 " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 See footnotes at end of device types 05 and 06. 1 2 U/ D A 5/ " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B " " " " " " " " " " " " " " 2 3 CK B 5/ A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B B A B A B A B A B A B A B A B A B A B A B 3 4 A B C D EP GND L ET B " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A " " " " " " " " " " " " " " " " B " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A " " " " " " " " " " " " " " " " B " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A " " " " " " " " " " " " " " " " B " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A " " " " " " " " " " " " " " " " B " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A A B " " " " " " " " " " " " " " " " " " " " " GND " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B B A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B B A " " " " " " " " " " " " " " B " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A A B " " " " " " " " " " " " " " " " " " 12 15 13 17 14 18 15 19 16 20 QD QC QB QA X L 5/ " " " " " " " " " " " " " " " H " " " " " " " " " " " " " " " " " " " " L L H " " " " " " " " " " " " " " " X L " " " " " " " H " " " " " " " L " " " " " " " H " " " " " " " " " " " " L L H " " " " " " " L " " " " " " " X L " " " H " " " L " " " H " " " L " " " H " " " L " " " H " " " " " " " " L L H " " " L " " " H " " " L " " " X L L H H L L H H L L H H L L H H L L H H L L H H L L H H L L H " " " " " " L L H H L L H H L L H H L L H H L L Ripple carry X H 5/ " " " " " " " " " " " " " " " " " " " " " " " " " " " " " L " " " H H L H H L H " " " " " " " " " " " " " " 4.5 V " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " Measured terminal VCC Limits Min Unit Max See 6/ MIL-M-38510/315D 95 MIL-STD883 method TABLE III. Group A inspection for device type 06 - Continued. Terminal conditions (pins not designated may be H 2.0 V or L 0.7 V or open). 4 5 6 7 8 9 10 11 5 7 8 9 10 12 13 14 Subgroup 7 Tc = +25C Functional tests 4/ MIL-STD883 method Cases E, F Cases 1/ 2 Test no. 3014 " " " " " " " " " " " " " " " " " " " 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 1 2 U/ D B 5/ " " " " " " " " " " " " " " " " " " " Repeat subgroup 7 at TC = +125 and TC = -55C. 96 See footnotes at end of device types 05 and 06. 2 3 CK A 5/ B A B A B A B A B A B A B A B A B A B 3 4 12 15 13 17 14 18 15 19 16 20 Ripple carry H " " " " " " " " " " " " " L " " H H L 4.5 V " " " " " " " " " " " " " " " " " " " A B C D EP GND L ET QD QC QB QA A " " " " " " " " " " " " " " " " " " " A " " " " " " " " " " " " " " " " " " " A " " " " " " " " " " " " " " " " " " " A " " " " " " " " " " " " " " " " " " " B " " " " " " " " " " " " " " A A B " " GND " " " " " " " " " " " " " " " " " " " A " " " " " " " " " " " " " " " " " " " B " " " " " " " " " " " " " " " " A A B L " " " " " " " " " " " " " " " " " " " H " " " " " " " L " " " " " " " " " " " H " " " L " " " H " " " L " " " " " " " H H L L H H L L H H L L H H L " " " " " Measured terminal VCC Limits Min Unit Max See 6/ MIL-M-38510/315D 8 Symbol TABLE III. Group A inspection for device type 06 - Continued. Terminal conditions (pins not designated may be H 2.0 V or L 0.7 V or open). 4 5 6 7 8 9 10 11 5 7 8 9 10 12 13 14 Subgroup 9 Symbol tPLH5 Tc = +25C tPHL5 tPHL15 MIL-STD883 method Cases E, F Cases 1/ 2 Test no. 1 2 See fig. 7 " " " " " " 108 109 110 111 112 113 114 115 5.0 V " " " " " " " " 116 " 2 3 U/ D IN IN IN IN IN 3 4 TABLE III. Group A inspection for device type 05- Continued. Terminal conditions (pins not designated may be H 2.0 V or L 0.7 V or open). 4 5 6 7 8 9 10 11 5 7 8 9 10 12 13 14 CK A B C D EP GND L ET 7/ GND " " " " 5.0 V " " GND " " " " " 5.0 V " GND " " " " " " 5.0 V GND " " " " " " " GND " " " " " " " IN 7/ 5.0 V " " IN " " " GND 2/ 8/ 7/ " " " GND " " " 5.0 V " " " " " " " " " " " " 117 " " " " " " " 5.0 V " " " " " " " " " " " 118 119 120 121 122 123 124 125 126 127 GND " " " " " " " 5.0 V 5.0 V IN 9/ IN " " " " " " IN 7/ GND IN GND " " " " " " 5.0 V " IN IN 7/ " GND " " " 5.0 V GND " " " " " GND " " " " " 5.0 V GND 5.0 V " " " " " " " " " " " " " " " " " " " " " " " " GND 128 GND GND 5.0 V GND " " " " " " " 129 IN " " " " " 130 131 GND GND IN 7/ GND GND " " " " " GND " 132 IN IN 7/ " " " 133 IN " " " tPHL11 97 tPLH9 " tPHL7 tPLH7 " " " tPHL11 IN GND 13 17 QC QB 14 18 15 19 QA Ripple carry OUT 16 20 Measured terminal VCC Unit Min Max 22 " " " " " " " OUT 5.0 V " " " " " " " " CK TO RC 3 " " " " " " " " 32 ns " " " " " " " " OUT " CK TO RC " 30 " CK TO QA CK TO QA CK TO QB CK TO QB CK TO QC CK TO QC CK TO QD CK TO QD ET to RC ET to RC " " " " " " " " " " 22 " " " " " " " 24 15 " " " " " " " " " " " 28 " " 22 " " " 24 15 " " " 28 " " 22 " OUT OUT OUT OUT OUT OUT OUT OUT OUT IN 5.0 V IN IN OUT OUT " " " " " " " " " " IN GND OUT " " 5.0 V GND " " " " " IN 5.0 V IN IN " " " " " IN GND " " " " 5.0 V OUT OUT OUT OUT OUT OUT CK TO QA CK TO QB CK TO QC CK TO QD CK TO QA CK TO QB CK TO QC CK TO QD Limits U/ D to RC U/ D to RC ET to RC ET to RC U/ D to RC tPLH9 " FMAX 10/ FMAX 10/ " 134 5.0 V IN " " 5.0 V OUT OUT OUT OUT " CK to Qn 25 MHz " 135 GND IN " " 5.0 V OUT OUT OUT OUT " CK to Qn 25 MHz See footnotes at end of device types 05 and 06. GND " U/ D to RC MIL-M-38510/315D tPLH12 tPLH5 tPHL5 tPLH5 tPHL5 tPLH5 tPHL5 tPLH5 tPHL5 tPHL7 tPLH7 QD 12 15 Subgroup 10 Tc = +125C Symbol tPLH5 tPHL5 tPHL15 MIL-STD883 method Cases E, F Cases 1/ 2 Test no. See fig. 7 " " " " " " 136 137 138 139 140 141 142 143 CK TO QA CK TO QB CK TO QC CK TO QD CK TO QA CK TO QB CK TO QC CK TO QD " 144 U/ D 2 3 3 4 CK A B C D EP GND L ET QD 12 15 13 17 14 18 15 19 16 20 QC QB QA Ripple carry VCC Measured terminal Limits Unit Min Max 26 " " " " " " " CK TO RC 3 " " " " " " " " 37 ns " " " " " " " " " 145 CK TO RC 35 " tPLH5 tPHL5 tPLH5 tPHL5 tPLH5 tPHL5 tPLH5 tPHL5 tPHL7 tPLH7 " " " " " " " " " " " 146 147 148 149 150 151 152 153 154 155 CK TO QA CK TO QA CK TO QB CK TO QB CK TO QC CK TO QC CK TO QD CK TO QD ET to RC ET to RC " " " " " " " " " " 26 " " " " " " " 28 18 " " " " " " " " " " " 33 " " 26 " " " 28 18 " " " 33 " " 26 " 98 tPLH9 " tPHL7 tPLH7 " " " tPHL11 tPLH9 " FMAX FMAX " " Same conditions as for subgroup 9. 156 157 158 159 160 161 162 163 Same tests, conditions and limits as for subgroup 10 except TC = -55C and VCC = 4.5 for FMAX. See footnotes at end of device types 05 and 06. U/ D to RC U/ D to RC ET to RC ET to RC U/ D to RC U/ D to RC CK to Qn CK to Qn 25 25 MHz MHz MIL-M-38510/315D tPLH12 " tPHL11 11 1 2 TABLE III. Group A inspection for device type 05- Continued. Terminal conditions (pins not designated may be H 2.0 V or L 0.7 V or open). 4 5 6 7 8 9 10 11 5 7 8 9 10 12 13 14 Subgroup 9 CK A B C D EP GND L ET tPHL15 tPLH12 tPLH5 tPHL5 tPLH5 tPHL5 tPLH5 tPHL5 tPLH5 tPHL5 tPHL7 tPLH7 tPHL11 See fig. 7 " " " " " " " " " " " " " " " " " " " 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 5.0 V " " " " " " " " " GND " " " " " " " 5.0 V 5.0 V IN IN 7/ " " " " 7/ " " " " " " " " " " " " " " 7/ " IN 7/ GND 5.0 V " " 5.0 V " " " GND GND 5.0 V GND " " " " " " 5.0 V " " GND " 5.0 V " GND 5.0 V " " " " GND GND 5.0 V GND " " " " 5.0 V " " GND " " 5.0 V GND " 5.0 V " " " GND " " " 5.0 V GND " " 5.0 V " " GND " " " GND " " 5.0 V " " GND " " " " " 5.0 V GND 5.0 V " " GND " " " " " " " " " " " " " " " " " " " " GND " " " GND " " " " " " " " " " " " " " " " IN " " " IN " " " " 5.0 V 5.0 V " " " " " " " 5.0 V 5.0 V 5.0 V GND " " " GND " " " " " " " " " " " " " IN IN GND tPLH9 " 150 IN IN " " " " " " 5.0 V tPHL7 tPLH7 tPHL11 " " " 151 152 153 GND GND IN IN 7/ IN IN 7/ GND " " GND " " GND " " GND " " " " " " " " tPLH9 " 154 IN IN " " " " " FMAX FMAX " " 155 156 5.0 V GND IN IN " 5.0 V " 5.0 V " 5.0 V " 5.0 V " " tPLH5 Tc = +25C tPHL5 99 See footnotes at end of device types 05 and 06. 1 2 U/ D 2 3 3 4 QD 12 15 13 17 QC QB 14 18 15 19 QA Ripple carry OUT 16 20 VCC OUT OUT OUT 5.0 V " " " " " " " " " " " " " " " " " " " " GND " " 5.0 V 5.0 V 5.0 V IN IN GND " " " " " " " 5.0 V " " " " " 5.0 V 5.0 V " " OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT Measured terminal " " CK TO QA CK TO QB CK TO QC CK TO QD CK TO QA CK TO QB CK TO QC CK TO QD CK TO RC CK TO RC CK TO QA CK TO QA CK TO QB CK TO QB CK TO QC CK TO QC CK TO QD CK TO QD ET to RC ET to RC U/ D to RC U/ D to RC ET to RC ET to RC U/ D to RC U/ D to RC CK to Qn CK to Qn Limits Unit Min Max 3 " " " " " " " " " " " " " " " " " " " " 22 " " " 32 " " " 35 33 22 32 22 32 22 32 22 32 28 24 32 " 28 " " " " 28 24 32 " " " " 22 25 25 ns " " " " " " " " " " " " " " " " " " " " " MHz MHz MIL-M-38510/315D method Cases E, F Cases 1/ 2 Test no. Symbol MIL-STD883 TABLE III. Group A inspection for device type 06. Terminal conditions (pins not designated may be H 2.0 V or L 0.7 V or open). 4 5 6 7 8 9 10 11 5 7 8 9 10 12 13 14 Subgroup 10 Tc = +125C Symbol tPLH5 tPHL5 tPHL15 MIL-STD883 method Cases E, F Cases 1/ 2 Test no. See fig. 7 " " " " " " 157 158 159 160 161 162 163 164 CK TO QA CK TO QB CK TO QC CK TO QD CK TO QA CK TO QB CK TO QC CK TO QD " 165 U/ D 2 3 3 4 CK A B C D EP GND L ET QD 12 15 13 17 14 18 15 19 16 20 QC QB QA Ripple carry VCC Measured terminal Limits Unit Min Max 26 " " " 36 " " " CK TO RC 3 " " " " " " " " 40 ns " " " " " " " " " 166 CK TO RC 38 " tPLH5 tPHL5 tPLH5 tPHL5 tPLH5 tPHL5 tPLH5 tPHL5 tPHL7 tPLH7 " " " " " " " " " " " 167 168 169 170 171 172 173 174 175 176 CK TO QA CK TO QA CK TO QB CK TO QB CK TO QC CK TO QC CK TO QD CK TO QD ET to RC ET to RC " " " " " " " " " " 26 36 26 36 26 36 26 36 32 28 " " " " " " " " " " " 37 " " 32 " " " 32 28 " " " 37 " " 32 " tPLH9 " tPHL7 tPLH7 " " " tPHL11 tPLH9 " FMAX FMAX " " Same conditions as for subgroup 9. 177 178 179 180 181 182 183 184 Same tests, conditions and limits as for subgroup 10 except TC = -55C and VCC = 4.5 for FMAX. See footnotes at end of device types 05 and 06. U/ D to RC U/ D to RC ET to RC ET to RC U/ D to RC U/ D to RC CK to Qn CK to Qn 25 25 MHz MHz MIL-M-38510/315D 100 tPLH12 " tPHL11 11 1 2 TABLE III. Group A inspection for device type 06. Terminal conditions (pins not designated may be H 2.0 V or L 0.7 V or open). 4 5 6 7 8 9 10 11 5 7 8 9 10 12 13 14 1/ Case 2, pins not referenced are N/C. 2/ Apply one clock pulse prior to test as follows: 3 V .2 V 0 V .2 V 3/ IIL limits (A) min/max values for circuits shown: Terminals IIL12 A, B, C, D IIL13 U/ D , CK, L IIL14 IIL15 Circuits A B C D E -160/-400 -0.5/-400 -160/-400 -135/-370 EP 160/-400 -150/-385 ET -140/-720 -280/-760 101 4/ Only a summary of attributes data is required. 5/ A = 3.0 V minimum; B = 0.0 V or GND. 6/ H > 1.5 V; L < 1.5 V; X = don't care. 7/ Apply one clock pulse with "L" low prior to test. 8/ Apply three clock pulses prior to test. 9/ Apply one clock pulse with "A" low prior to test. 10/ On (QA, QB, QC, and QD) shall respond as specified in the truth table with the minimum FMAX frequency input to "CK". F G MIL-M-38510/315D Parameter Subgroup Symbol 1 VOL Tc = +25C VOH MIL-STD883 method 1 2 2 3 Test no. B QB 1 2 3 4 5 " 3006 " " " " 6 7 8 9 10 11 " 12 13 14 15 16 17 18 19 20 3 4 QA Count down Count Up QC QD 4 mA 0.7 V 0.7 V 2.0 V " " " " " " 4 mA 4 mA 4 mA 2/ 0.7 V -0.4 mA 2.0 V GND GND " " " " -0.4 mA -0.4 mA -0.4 mA 2.0 V -18 mA -18 mA -18 mA " " " " " " " " " 102 3009 " " " 21 22 23 24 IIL10 " 25 " IIL11 " " " 26 27 28 0.4 V " " " 3010 " " " " " " " 29 30 31 32 33 34 35 36 2.7 V " " " " " " " " " " " " " " " " 37 38 39 40 41 42 43 44 5.5 V " " " " " " " " IIH17 IIH18 See footnotes at end of device types 07 and 08. " " " " 0.4 V 0.4 V 2.7 V 2.7 V 5.5 V 5.5 V D 0.7 V 2.0 V C Load 0.7 V " 2/ 0.7 V " " " " Ripple Carry 13 17 14 18 Borrow Clear A VCC terminal 0.7 V " " " " 0.7 V 4.5 V " " " 4.5 V QA QB QC QD Ripple carry Borrow QA QB QC QD Ripple Carry Borrow A B C D Load Clear Count up Count down A B C D 4 mA 4 mA 2.0 V 2.0 V 0.7 V " " " -0.4 mA 2.0 V 0.7 V " " " " 15 19 2.0 V 2.0 V -0.4 mA -18 mA -18 mA -18 mA -18 mA -18 mA 0.4 V 0.4 V GND " " " GND " " " 0.4 V 0.4 V 0.4 V 2.7 V 2.7 V 5.5 V " " " 2.7 V 5.5 V " " " 5.5 V 5.5 V 5.5 V " " " 5.5 V 4.5 V " " " " " " " " " " " " " " 5.5 V " " " Limits Measured Unit Min Max 0.4 " " " " V " " " " " " " " " " " 2.5 " " " " " 3/ " " " -1.5 " " " " " " " " " " " " " " " " 3/ " " " A " " " " Load " " " " " " Clear Count up Count down A B C D Load Clear Count up Count down A B C D Load Clear Count up Count down " " " " " " " " " 20 " " " " " " " " " " " " " " " 100 " " " " " " " " " " " " " " " 2.7 V " " " " " " " " 5.5 V " " " " " " " " 2.7 V 5.5 V " " " " 16 20 MIL-M-38510/315D 3007 " " " " VIC IIL9 Cases E, F Cases1/ 2 TABLE III. Group A inspection for device types 07 and 08. Terminal conditions (pins not designated may be H 2.0 V; or L 0.7 V; or open). 4 5 6 7 8 9 10 11 12 5 7 8 9 10 12 13 14 15 Subgroup Symbol 1 IOS Tc = +25C ICC MIL-STD883 method Cases E, F Cases1/ 2 1 2 2 3 Test no. B QB 3011 " " " " 45 46 47 48 49 " 50 3005 51 3 4 QA TABLE III. Group A inspection for device types 07 and 08 - Continued. Terminal conditions (pins not designated may be H 2.0 V; or L 0.7 V; or open). 4 5 6 7 8 9 10 11 12 5 7 8 9 10 12 13 14 15 Count down Count Up QC QD GND 5.5 V GND GND GND 5.5 V 5.5 V GND GND " " " " D C 5.5 V 5.5 V Load 2 Same tests, terminal conditions, and limits as for subgroup 1, except TC = +125C and VIC tests are omitted. 3 Same tests, terminal conditions, and limits as for subgroup 1, except TC = -55C and VIC tests are omitted. 14 18 Borrow Clear A VCC terminal Min Max GND " " " " 5.5 V 5.5 V " " " " 4/ " " " " 4/ " " " " mA " " " " " QA QB QC QD Ripple carry Borrow " " " VCC 34 " GND " " " GND " " Ripple Carry 13 17 GND GND GND 15 19 16 20 Limits Measured Unit " See footnotes at end of device types 07 and 08. MIL-M-38510/315D 103 Subgroup Symbol 7 FuncTc = +25C tional tests 5/ MIL-STD883 method 1 2 2 3 3 4 Test no. B QB QA A 6/ " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " L " " " " H " " " L " " " H " " " L " " " " " " " " " H " " " L " " " H " " " L " " " " H L H H L L L L L H H L L H H L L H H L L H H L L H H L L H H L L H H L L H H L L H H L L H H L L H H L H H L L 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 See footnotes at end of device types 07 and 08. Count down A " " " " " " " " " " " " " " " " " " " " " B A B A B A B A B A B A B A B A B A B A B A " " " " " " Count Up A A B A B A B A B A B A B A B A B A B A B A " " " " " " " " " " " " " " " " " " " " " " " " " " " " QC QD GND D C Load L " " " " " " " " H " " " " " " " L " " " " " " " " " H " " " " " " " L " " " " " " " " H L H H L L L " " " " " " " " " " " " " " " " H " " " L L H " " " L " " " " " " " " " " " " " " " H H L H H L L GND " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B " " A " " Ripple Carry H " " " " " " " " " " " " " " " " " " " L H " " " " " " " " " " " " " " " " " " " " " " " " " " " " 13 17 14 18 15 19 16 20 Borrow Clear A VCC H " " " " " " " " " " " " " " " " " " " " " L H H " " " " " " " " " " " " " " " " " L H " " " " " " A B 6/ " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A B B A B A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " 4.5 V " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " Limits Measured terminal See 7/ Unit Min Max MIL-M-38510/315D 104 3014 " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " Cases E, F Cases1/ 2 TABLE III. Group A inspection for device types 07 - Continued. Terminal conditions (pins not designated may be H 2.0 V; or L 0.7 V; or open). 4 5 6 7 8 9 10 11 12 5 7 8 9 10 12 13 14 15 Subgroup Symbol MIL-STD883 method Cases E, F Cases1/ 2 Test no. 7 FuncTc = +25C tional tests 5/ 8 3014 " " " " " " " " " " " " " 102 103 104 105 106 107 108 109 110 111 112 113 114 115 1 2 2 3 3 4 B QB QA A 6/ A B " " " " " " " " " " " H " " L " " " " " " " " " " H " " L " " " " " " " " " " TABLE III. Group A inspection for device types 07 - Continued. Terminal conditions (pins not designated may be high 2.0 V; or low 0.7 V; or open). 4 5 6 7 8 9 10 11 12 5 7 8 9 10 12 13 14 15 Count down A " " " B A " " " " B A A A Count Up A " " " " " B A " " " " B A QC QD GND D C H " " L " " " " " " " " " " H " " L " " " " " " " " " " GND " " " " " " " " " " " " " A A B " " " " " " " " " " " A A B " " " " " " " " " " " Load B 6/ A A B " " " " A " " " " " Ripple Carry H " " " " " " " " " " " " " 13 17 14 18 15 19 16 20 Borrow Clear A VCC H " " " L H " " " " L H " " B " " " " " " " " A " " " " A A B " " " " " " " " " " " 4.5 V " " " " " " " " " " " " " Limits Measured terminal Unit Min Max See 7/ Repeat subgroup 7 at TC = +125 and TC = -55C. See footnotes at end of device types 07 and 08. MIL-M-38510/315D 105 Subgroup Symbol 7 FuncTc = +25C tional tests 5/ MIL-STD883 method 1 2 2 3 3 4 Test no. B QB QA B 6/ " " " A " " " B " " " A " " " B " " " A " " " B " " " A " " " " " " " " " " " " " " " " " " " " " " " " " " " L " " " H " " " L " " " H " " " L " " " H " " " L " " " H " " L " " " H " " " L " " " H " " " L " " " H " " " L L L H H L L H H L L H H L L H H L L H H L L H H L L H H L L H L " " " H H L L H H L L H H L L H H L L H H L L H 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 See footnotes at end of device types 07 and 08. Count down A 6/ " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B A B A B A B A B A B A B A B A B A B A B A Count Up A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " QC QD GND D C Load L " " " " " " " H " " " " " " " L " " " " " " " H " " " " " " L " " " H " " " " " " " L " " " " " " " H " " " " L " " " " " " " " " " " " " " " H " " " " " " " " " " " " " " L " " " H " " " " " " " " " " " " " " " L " " " " GND " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B " " " " " " " " " " " " " " " A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B " " " " " " " A " " " " " " " B " " " " " " " A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B B A " " " " " " " " " " " " " " " " " " " " " " " Ripple Carry H " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " 13 17 14 18 15 19 16 20 Borrow Clear A VCC H " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " L H " " " " " " " " " " " " " " " " " " " " B " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A A B " " " " " " " " " " " " " " " " " " " " " " B B A A B B A A B B A A B B A A B B A A B B A A B B A A B B A " " " " " " " " " " " " " " " " " " " " " " " " " 4.5 V " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " Limits Measured terminal See 7/ Unit Min Max MIL-M-38510/315D 106 3014 " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " Cases E, F Cases1/ 2 TABLE III. Group A inspection for device types 08 - Continued. Terminal conditions (pins not designated may be high 2.0 V; or low 0.7 V; or open). 4 5 6 7 8 9 10 11 12 5 7 8 9 10 12 13 14 15 Subgroup Symbol 7 FuncTc = +25C tional tests 5/ 3014 " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " Cases E, F Cases1/ 2 1 2 2 3 3 4 Test no. B QB QA A 6/ " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " L " " H " " " L " " " " " H " " " L " " " H " " " L " " " H " " " L " " " H " " " L " " " " " " H " " " " H L L H H L L H H L L H H L L H H L L H H L L H H L L H H L L H H L L H H L L H H L " " " " " " H " " " " 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 Repeat subgroup 7 at TC = +125 and TC = -55C. See footnotes at end of device types 07 and 08. Count down B 6/ A B A B A B A B A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B A " " " " B A Count Up A " " " " " " " " " B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A A B A " " " " B A A A QC QD GND D C Load H " " L " " " " " " " " " " " " " H " " " " " " " L " " " " " " " H " " " " " " " L " " " " " " H " " " " L " " " " " " " " " " " " " " " " " " " " " " " " H " " " " " " " " " " " " " " " L " " " " " " H " " " " GND " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B " " " " Ripple Carry H " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " L H " " " " " " " L H " " 13 17 14 18 15 19 Borrow Clear A VCC A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " 4.5 V " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " H " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " L H " " " " " " B 8/ " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A " " " " B " " " " " 16 20 Limits Measured terminal See 7/ Unit Min Max MIL-M-38510/315D 107 8 MIL-STD883 method TABLE III. Group A inspection for device types 08 - Continued. Terminal conditions (pins not designated may be H 2.0 V; or L 0.7 V; or open). 4 5 6 7 8 9 10 11 12 5 7 8 9 10 12 13 14 15 Subgroup MIL-STD883 Symbol method 9 FMAX 8/ Tc = +25C FMAX 8/ tPLH8 tPHL10 tPLH9 108 tPHL12 1 2 3 2 3 4 B QB 5 7 QA Count down Count up 3003 9/ 116 161 OUT 5.0 V IN " 117 162 OUT IN 5.0 V " " " " " " " " " " " " " " " " " " " " " " " " " " " " 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 OUT See footnotes at end of device types 07 and 08. 5.0 V 8 QC 9 QD OUT OUT OUT OUT GND OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT 5.0 V 5.0 V " " " IN " " " 5.0 V " " " IN " " " IN " " " 5.0 V " " " IN " " " 5.0 V " " " OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT 10 GND 12 D 13 C 14 Load 15 Ripple carry 17 Borrow 14 15 16 18 19 20 Measured VCC terminal Min 5.0 V Count up to QA 22 " Count down to QA 22 " " " " " " " " " " " " " " " " " " " " " " " " " " " " Load to QA Load to QB Load to QC Load to QD Load to QA Load to QB Load to QC Load to QD Count up to QA Count up to QB Count up to QC Count up to QD Count down to QD Count down to QC Count down to QB Count down to QA Count up to QA Count up to QB Count up to QC Count up to QD Count down to QD Count down to QC Count down to QB Count down to QA Clear to QA Clear to QB Clear to QC Clear to QD 3 " " " " " " " " " " " " " " " " " " " " " " " " " " " Clear GND 5.0 V GND " 5.0 V GND " " " " " " " " " " " " " " " " " " " " " " " " " " " " IN " " " " " " " 5.0 V " " " " " " " " " " " " " " " 10/ " " " GND " " " GND " " " " " " " " " " " " " " " " " " " IN " " " 5.0 V 5.0 V " GND GND 5.0 V 5.0 V A 5.0 V GND 5.0 V Limits Unit Max MHz MHz 45 " " " " " " " 43 " " " " " " " 52 " " " " " " " 40 " " " ns " " " " " " " " " " " " " " " " " " " " " " " " " " " MIL-M-38510/315D tPHL11 Cases E, F Case 1/ 2 (Device type) 07 08 TABLE III. Group A inspection for device types 07 and 08 - Continued. Terminal conditions (pins not designated may be high 2.0 V; or low 0.7 V; or open). 4 5 6 7 8 9 10 11 12 13 Subgroup Symbol 9 FMAX 8/ Tc = +25C FMAX 8/ tPLH8 tPHL10 tPLH9 109 tPHL12 11 Cases E, F Case 1/ 2 (Device type) 07 08 1 2 3 14 15 16 2 3 4 5 7 8 9 10 12 13 14 15 17 18 19 20 Measured Limits B QB QA Count down Count up QC QD GND D C Load Ripple carry Borrow Clear A VCC terminal Min Unit 3003 9/ 146 191 Count up to QA 22 " 147 192 Count down to QA 22 " " " " " " " " " " " " " " " " " " " " " " " " " " " " 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 Load to QA Load to QB Load to QC Load to QD Load to QA Load to QB Load to QC Load to QD Count up to QA Count up to QB Count up to QC Count up to QD Count down to QD Count down to QC Count down to QB Count down to QA Count up to QA Count up to QB Count up to QC Count up to QD Count down to QD Count down to QC Count down to QB Count down to QA Clear to QA Clear to QB Clear to QC Clear to QD 3 " " " " " " " " " " " " " " " " " " " " " " " " " " " Same terminal conditions as for subgroup 9. Same tests, terminal conditions, and limits as for subgroup 10, except TC = -55C. See footnotes at end of device types 07 and 08. Max MHz MHz 63 " " " " " " " 60 " " " " " " " 73 " " " " " " " 56 " " " ns " " " " " " " " " " " " " " " " " " " " " " " " " " " MIL-M-38510/315D tPHL11 MIL-STD883 method TABLE III. Group A inspection for device types 07 and 08 - Continued. Terminal conditions (pins not designated may be high 2.0 V; or low 0.7 V; or open). 4 5 6 7 8 9 10 11 12 13 1/ Case 2, pins not referenced are N/C. 2/ Apply 0.7 V for device type 07; apply 2.0 V for device type 08. 3/ IIL limits (A) min/max values for circuits shown: Parameter IIL9 IIL10 A B C D E F G -160/-400 -160/-400 -160/-400 -100/-340 -100/-340 -120/-360 -135/-370 A " " " " " " " B " " " " " " " C " " " " " " " D " " " " " " " -100/-340 " -150/-380 -120/-360 -120/-360 " -100/-340 " " -135/-370 Load " -150/-380 Count up " " " " " " " Count down " " " " " " " 110 4/ IOS limits (mA) min/max values for circuits shown: -15/-100 for circuits A, C, D, E, F, and G and -15/-110 for circuit B. 5/ Only a summary of attributes data is required. 6/ A = 3.0 V minimum; B = 0.0 V or GND. 7/ H > 1.5 V; L < 1.5 V; X = don't care. 8/ FMAX minimum limit specified is the frequency of the input pulse. The output frequency shall be one-half of the input frequency. 9/ See figure 8 for device type 07 and figure 9 for device type 08. 10/ Apply momentary GND, then 4.5 V minimum prior to input pulses. Maintain 4.5 V minimum for measurement. MIL-M-38510/315D -160/-400 " Clear IIL11 Circuits Terminals Subgroup Symbol 1 VOL Tc = +25C VOH MIL-STD883 method 3007 " " " " " 3006 " " " " " VIC Cases E, F Cases1/ 2 1 2 2 3 3 4 QA B QB 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 0.7 V 4 mA Enable G Down/ up QC QD 4 mA 4 mA 4 mA 2.0 V 2/ 2.0 V 0.7 V 2.0 V 0.7 V -0.4 mA -0.4 mA -0.4 mA -0.4 mA 0.7 V 2.0 V 2.0 V -18 mA -18 mA -18 mA 5.5 V D C 0.7 V 0.7 V 2.0 V 2/ 2.0 V 2.0 V 0.7 V 0.7 V Load 0.7 V " " " " " " " " " " " Max/ Min 14 18 15 19 Ripple carry Clock A 0.7 V 4 mA 4 mA 0.7 V 2.0 V 2.0 V -0.4 mA 0.7 V -0.4 mA -18 mA -18 mA -18 mA -18 mA -18 mA Limits Measured VCC terminal 4.5 V " " " " " " " " " " " " " " " " " " " QB QA QC QD Max/Min Ripple carry QB QA QC QD Max/Min Ripple carry B Enable G Down/up D C Load Clock A 5.5 V Enable G " " " " " " " B Down/up D C Load Clock A Unit Min Max 0.4 " " " " " -1.5 V " " " " " " " V " " " " " " " " " " " " " " " " " " " 3/ 3/ A " " " " " " " " " " " " " " " " " " " " " 2.5 V " " " " " 21 IIL8 " " " " " " " 22 23 24 25 26 27 28 IIH15 3010 29 2.7 V " " Enable G 60 " IIH16 " 30 5.5 V " " Enable G 300 " IIH17 " " " " " " " 31 32 33 34 35 36 37 " " " " " " " B Down/up D C Load Clock A 20 " " " " " " " " " " " " " 111 3009 0.4 V 0.4 V 2.7 V 2.7 V " 16 20 IIL7 See footnotes at end of device types 09 and 13. 0.4 V GND GND " " " " " " " " " " " " " " " " " " " 13 17 " " " " " " " " " " " " " " GND 0.4 V 0.4 V " " 0.4 V 0.4 V GND 0.4 V 5.5 V 2.7 V 2.7 V 5.5 V 5.5 V 2.7 V 2.7 V 5.5 V 2.7 V MIL-M-38510/315D Test no. TABLE III. Group A inspection for device types 09 and 13 - Continued. Terminal conditions (pins not designated may be H 2.0 V; or L 0.7 V; or open). 4 5 6 7 8 9 10 11 12 5 7 8 9 10 12 13 14 15 Subgroup Symbol 1 IIH18 Tc = +25C IOS ICC MIL-STD883 method Cases E, F Cases1/ 2 1 2 2 3 3 4 QB QA Test no. B 3010 " " " " " " 3011 " " " " " 38 39 40 41 42 43 44 45 46 47 48 49 50 5.5 V 3005 51 GND TABLE III. Group A inspection for device types 09 and 13 - Continued. Terminal conditions (pins not designated may be H 2.0 V; or L 0.7 V; or open). 4 5 6 7 8 9 10 11 12 5 7 8 9 10 12 13 14 15 Enable G Down/ Up QC QD 5.5 V 5.5 V GND GND GND GND GND 5.5 V 5.5 V GND GND GND GND " " " " " " " " " " " " " D Load Max/ Min 14 18 15 19 Ripple Carry Clock A VCC terminal 5.5 V 5.5 V " " " " " " " " " " " " B Down/up D C Load Clock A QB QA QC QD Max/Min Ripple carry " VCC 5.5 V 5.5 V 5.5 V 5.5 V " " 5.5 V 5.5 V 5.5 V GND GND 5.5 V GND " " " " 5.5 V GND GND GND GND 2 Same tests, terminal conditions, and limits as for subgroup 1, except TC = +125C and VIC tests are omitted. 3 Same tests, terminal conditions, and limits as for subgroup 1, except TC = -55C and VIC tests are omitted. GND GND GND GND 16 20 Limits Measured Unit Min Max 4/ " " " " " 100 " " " " " " 4/ " " " " " A " " " " " " mA " " " " " 35 " 112 MIL-M-38510/315D See footnotes at end of device types 09 and 13. C 13 17 Subgroup Symbol MIL-STD883 method 7 FuncTc = +25C tional tests 5/ Test no. 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 See footnotes at end of device types 09 and 13. 1 2 2 3 3 4 B QB QA A 6/ " " B B B A " " " " B A " " " " " " " " " B B A " " B " " " " " A B A B A B A B A B A B A A B B A H " " " " " " L " " " H " " " L " " " H " " " L " " " H " " " L " " " H " " " L " " " " " " H " " " H " " " " " " L L H H L L H H L L H H L L H H L L H H L L H H L L H H L L H H L " " " " " " H H L L Enable G B 6/ A " " " B " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A " " B " " " " " Down/ up B " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A " " " " " " " " " QC QD GND D C Load Max/Min H " " " " " " L " " " " " " " H " " " " " " " L " " " " " " " H " " " " " " " L " " " " " " H " " " H " " " " " " L " " " " " " " " " " " " " " " H " " " " " " " " " " " " " " " L " " " " " " H " " " GND " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A " " B " " A " " " " B A " " " B A " " B B A A B " " A " " " " B A B A B A B A B A B B A " " B B A A " " B " " A " " " " B A A B " " A B A " " B B A " " B B A A B B A B A B A B A B A B A B B A B B A B B A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " H " " " " " " L " " " " " " " " " " " " " " " " " " " " " " " " " " " " " H H L H " " " " " L " " " 13 17 14 18 15 19 16 20 Ripple Carry H " " " " " L H " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " L H " " " " " L H " " " Clock A VCC A " " B A A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A " " B A A B A B A B A " " B " " A " " B " " A A B B A B B A B A B B A A B A " " B " " A B A " " B A B A B " " " A B B A 4.5 V " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " Limits Measured terminal See 7/ Unit Min Max MIL-M-38510/315D 113 3014 " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " Cases E, F Cases1/ 2 TABLE III. Group A inspection for device types 09 - Continued. Terminal conditions (pins not designated may be H 2.0 V; or L 0.7 V; or open). 4 5 6 7 8 9 10 11 12 5 7 8 9 10 12 13 14 15 Subgroup 7 Tc = +25C Functional tests 5/ MIL-STD883 method 3014 " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " Test no. 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 1 2 3 4 B QB QA A 6/ B A A A B B A A A B B B A B A B A A A B B B A A A B A B A " " " B B A B A B A A B " " " " " A " " L " " " H " " " L " " " H " " " L " " " H " " " L " " " H " " " " L L H L H L H " " " " " " " " " " H H L L H H L L H H L L H H L L H H L L H H L L H H L L H " " " " L H L H L H L " " " " " " " " " " Repeat subgroup 7 at TC = +125 and TC = -55C. See footnotes at end of device types 09 and 13. 2 3 TABLE III. Group A inspection for device types 09 - Continued. Terminal conditions (pins not designated may be H 2.0 V; or L 0.7 V; or open). 4 5 6 7 8 9 10 11 12 5 7 8 9 10 12 13 14 15 Enable G B 6/ " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A " " " " B " " " " " A B " " " " " Down/ up A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B " " " " " A " " " " " B " " A " " " " QC QD GND D C Load Max/Min H " " " L " " " " " " " H " " " " " " " L " " " " " " " H " " " " L H L H L H L " " " " " " " " H H H " " " " " " " " " " " L " " " " " " " " " " " " " " " H " " " " L L H L H L H " " " " " " " " L L GND " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B A B B A A B A B B A B B A B A B A B B B A B B A A B A B A " " " B B A B A B A A B " " " " " " " " A A B B A B A B A A B B B A B A B A B B A A B B B A B A B A " " " B A B A B A B B A " " " " " " " " A " " " " " " " " " " " " " " " " " " " " " " " " " " " " B " " " " " " " " " " A " " " " " " " B A L " " " " " " " " " " " " " " " " " " " " " " " " " H H L L H " " L " " " " " " " " " " " " " " " " 13 17 Ripple Carry H " " " " " " " " " " " " " " " " " " " " " " " " " " L H H L H " " " " " " " " " " " " " " " " " " 14 18 15 19 16 20 Clock A VCC A B A B A B A B A B A B A B A B A B A B A B A B A B A B A A B A B " " " " " " A " " " " " " " " B B B B A A B A A A B B A A B A B B A B A " " " " B A A B A B A " " " B A B A B A B B A " " " " B A B B 4.5 V " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " Limits Measured terminal See 7/ Unit Min Max MIL-M-38510/315D 114 8 Symbol Cases E, F Cases1/ 2 Subgroup Symbol 7 FuncTc = +25C tional tests 5/ MIL-STD883 method 1 2 2 3 3 4 Test no. B QB QA 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 B 6/ " " " " " A A B B A B " " A B A " " " B A A B B B A B A A B " " " " A " " " " " " " " B B A " " " L " " " " " " " " H " " " L " " " H " " " L " " " " " " " " " " " " " " " " " H " " " L " " " H " " H " " " " L L H H L L H H L L H H L L H H L L H H L L H " " " " " L L H H L L H H L L H H L L H H L See footnotes at end of device types 09 and 13. Enable G A 6/ " " B " " " " " " " " " " " " " " " " " " " " " " " " A " " " B " " " " " " " " " " " " " " " " " Down/ up B " " " " " " " " " " " " " " " " " " " " " " " " " " " A " " " " " " " " " " " " " " " " " " " " " QC QD GND D C Load Max/Min L " " " " " " " " " " " " H " " " " " " " L " " " " " " " " " " " " " " " " " H " " " " " " " L " " H " " " " L " " " " " " " " " " " " " " " H " " " L " " " " " " " " " H " " " L " " " " " " " " " " GND " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A " " " " " " " " B A " " " " B " " " A B A A B " " A A B B A " " " B " " " A " " " B " " " A " " " B " " " " " A " " B A B B A A B A B B A B A A B " " A B A A B B A A B " " " A " " " B B A " " " " " B 6/ A " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " H " " " " L " " " " " " " " " " " " " " " " " H H L " " " " " " " H H L L " " " " " " " " " " " " " 13 17 14 18 15 19 16 20 Ripple carry H " " " L H " " " " " " " " " " " " " " " " " " L H " " " " " " " " L H H " " " " " " " " " " " " " Clock A VCC B B A A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A A " " " " " " " B B A " " B " " " " " A B A A B " " A A B B A A B " " A " " " " B " " " A B B A " " 4.5 V " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " Limits Measured terminal See 7/ Unit Min Max MIL-M-38510/315D 115 3014 " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " Cases E, F Cases1/ 2 TABLE III. Group A inspection for device types 13 - Continued. Terminal conditions (pins not designated may be H 2.0 V; or L 0.7 V; or open). 4 5 6 7 8 9 10 11 12 5 7 8 9 10 12 13 14 15 Subgroup Symbol 7 FuncTc = +25C tional tests 5/ 3014 " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " Cases E, F Cases1/ 2 Test no. 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 1 2 3 4 B QB QA B 6/ " " " A A B " " A " " B " " " " " " " " A " " B " " " A A B " " " " " A A B B A " " " " " " " H L " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " H H L " " " " " " " " H L H H L L " " " " H H L H " " " " " " " " " " L H " " " " " L " " " " H L H L " " " " H " " L H Repeat subgroup 7 at TC = +125 and TC = -55C. See footnotes at end of device types 09 and 13. 2 3 Enable G B 6/ " " " A " " B " " " " " " " A " " " " " B " " " " " " " " " " A " " " " " " B " " " " " " " " Down/ up A 6/ " " " " " " " " " " " " " " " " " B " " " " " " " " " " " " " A " " " " " B " " A " " B " " " QC QD GND D C Load Max/Min L " " " " " " " " " " " " " " " " " " " " " " L H " " " " " L " " " " " H H L " " " " " " " " H L " " " " " " " " H " " " " " " " " " " " " " L " " " " " " H " " " " " L " " " " " " H " " L H GND " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " B " " " A A B " " A " " " " B " " " " " " A " " B " " " A " " " " B B A B " " " A " " B B A " " B 6/ " " " A A B " " A " " B " " " " " " " " A " " " " " " B " " " " A A B A A B B A " " " " " " " A " " " " " " " " " " " B A " " " " " " " " " " B " " A " " B B A " " B " " " A " " " " " " " B L " " H " " " " " L " " " " " " " " H " " " " L " " " " " " " " " " " " " " " " " H H L H H L H 13 17 Ripple Carry H " " " " " " " L H " " " " " " " " " " " " L H " " " " " " " " " " " " " " " " " " L H H L H H 14 18 15 19 16 20 Clock A VCC B A B A A B A A B A B A " " " " B A A B A A B A A B A " " B B A A B A " " " " " " " B A A B A A B B A A B " " " " A B A " " B " " " " " " A " " " " " " B " " " " A " " B A B B A " " B B A " " 4.5 V " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " Limits Measured terminal See 7/ Unit Min Max MIL-M-38510/315D 116 8 MIL-STD883 method TABLE III. Group A inspection for device types 13 - Continued. Terminal conditions (pins not designated may be H 2.0 V; or L 0.7 V; or open). 4 5 6 7 8 9 10 11 12 5 7 8 9 10 12 13 14 15 Subgroup MIL-STD883 Symbol method Cases E, F Case 1/ 2 (Device type) 09 13 1 2 3 TABLE III. Group A inspection for device types 09 and 13 - Continued. Terminal conditions (pins not designated may be H 2.0 V; or L 0.7 V; or open). 4 5 6 7 8 9 10 11 12 13 2 3 4 5 B QB QA 152 150 OUT 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 OUT tPLH12 " 169 tPHL15 " 170 tPHL13 tPLH11 tPHL14 Enable Down/ G up QC 9 QD 10 GND 12 D 13 C 14 Load 15 Max/Min 17 Ripple carry 16 18 19 20 Clock 117 GND GND 5.0 V IN GND " " " " " " " GND " " " " " " " " " " " " " " " " " " " " " " " IN " " " " " " " 5.0 V " " " " " " " GND " " " " " " " IN " " " " " " " 167 " " " " OUT 168 " " " " OUT See footnotes at end of device types 09 and 13. 5.0 V GND 8 15 OUT OUT OUT OUT GND OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT 5.0 V 5.0 V GND GND A Limits Measured terminal Unit Min VCC Max 5.0 V Ck to QA 18 " " " " " " " " " " " " " " " " Load to QA Load to QB Load to QC Load to QD Load to QA Load to QB Load to QC Load to QD Ck to QA Ck to QB Ck to QC Ck to QD Ck to QA Ck to QB Ck to QC Ck to QD 3 " " " " " " " " " " " " " " " 38 " " " 55 " " " 29 " " " 41 " " " ns " " " " " " " " " " " " " " " " " Ck to Max/Min " 47 " " " Ck to Max/Min " 57 " 5.0 V GND MHz MIL-M-38510/315D 3003 9/ " " " " " " " " " " " " " " " " 9 FMAX 8/ Tc = +25C tPLH10 7 14 Subgroup MIL-STD883 Symbol method 1 2 3 2 3 4 5 B QB QA Enable G 7 Down/ up 8 QC 9 QD 10 GND 12 D 13 C 14 Load 15 Max/Min 17 Ripple carry 14 15 16 18 19 20 Clock A Limits Measured terminal Unit Min VCC 171 169 Ck to QA 18 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 Load to QA Load to QB Load to QC Load to QD Load to QA Load to QB Load to QC Load to QD Ck to QA Ck to QB Ck to QC Ck to QD Ck to QA Ck to QB Ck to QC Ck to QD 3 " " " " " " " " " " " " " " " tPLH12 " 188 186 Ck to Max/Min tPHL15 " 189 187 Count up to QB tPHL13 tPLH11 tPHL14 Same terminal conditions as for subgroup 9. 118 Same tests, terminal conditions, and limits as for subgroup 10, except TC = -55C. See footnotes at end of device types 09 and 13. Max MHz 53 " " " 77 " " " 41 " " " 57 " " " ns " " " " " " " " " " " " " " " " 66 " " 80 " MIL-M-38510/315D 3003 9/ " " " " " " " " " " " " " " " " 10 FMAX 8/ Tc = +125C tPLH10 11 Cases E, F Case 1/ 2 (Device type) 09 13 TABLE III. Group A inspection for device types 09 and 13 - Continued. Terminal conditions (pins not designated may be H 2.0 V; or L 0.7 V; or open). 4 5 6 7 8 9 10 11 12 13 1/ Case 2, pins not referenced are N/C. 2/ Apply 2.0 for device type 09; apply 0.7 V for device type 13. 3/ IIL limits (A) min/max values for circuits shown: Parameter IIL7 IIL8 Circuits Terminals A B C D E F G -360/-1080 -160/-400 -360/-1080 -360/-1080 -360/-1080 -360/-1080 -360/-1080 A, B, C, D -130/-400 -160/-400 -160/-400 -160/-400 -120/-360 -120/-360 -120/-360 Down/up " " -150/-380 " " " " Enable G Clock Load " " " " " " " -100/-340 " " -100/-340 " " " IOS limits (mA) min/max values for circuits shown: -15/-100 for circuits A, C, D, E, F, and G and -15/-110 for circuit B. 5/ Only a summary of attributes data is required. 6/ A = 3.0 V minimum; B = 0.0 V or GND. 7/ H > 1.5 V; L < 1.5 V; X = don't care. 8/ FMAX minimum limit specified is the frequency of the input pulse. The output frequency shall be one-half of the input frequency. 9/ See figure 10 for device type 09 and figure 12 for device type 13. MIL-M-38510/315D 119 4/ Subgroup 1 Tc = +25C Symbol VOL MIL-STD883 method Cases A, B, C, D Cases1/ 2 1 2 2 3 TABLE III. Group A inspection for device types 10. Terminal conditions (pins not designated may be H 2.0 V; or L 0.7 V; or open). 3 4 5 6 7 8 9 10 11 4 6 8 9 10 Test no. B VCC RO(1) RO(2) 3007 " 1 2 GND 2.0 V 4.5 V " 2.0 V " 2.0 V " " " 3006 " " " " " GND 2/ 3/ 2/ 4/ 2/ 5/ " " " " " " " " " " 5.5 V " " " 2/ " " " " " 2/ " " " NC NC NC 12 QD 13 QC 14 GND GND " 16 12 13 14 18 19 20 QB QA 4 mA 4 mA +IIL3 (max) NC Limits Measured terminal A QA QB 0.4 " V " " " QC QD QA QB QC QD A B RO(1) RO(2) RO(1) RO(2) " " " " " " " " " " " " mA " IIL1 3009 " -18 mA 5.5 V 0.4 V IIL2 " 15 IIL3 " 16 " 2/ 2/ " " " " " IIH1 IIH1 IIH2 IIH2 3010 " " " 17 18 19 20 " " " " 2.7 V GND 5.5 V GND GND 2.7 V GND 5.5 V " " " " RO(1) RO(2) RO(1) RO(2) IIH3 IIH4 " 21 " 5.5 V 5.5 V " 2.7 V A 80 " " 22 " " " " 5.5 V A 400 " IIH5 " 23 2.7 V " " " " B IIH6 " 24 5.5 V " " " " B 80 " IOS 3011 " " " 25 26 27 28 GND 2/ 3/ 2/ 4/ 2/ 5/ " " " " 2/ " " " 2/ " " " " " " " 3005 29 GND " -18 mA 0.4 V 4 mA -0.4 mA -0.4 mA -18 mA 120 GND GND 2 Same tests, terminal conditions, and limits as for subgroup 1, except TC = +125C and VIC tests are omitted. 3 Same tests, terminal conditions, and limits as for subgroup 1, except TC = -55C and VIC tests are omitted. See footnotes at end of device type 10. " -0.4 mA -0.4 mA 2/ 3/ GND " " -18 mA 0.4 V GND GND 2/ 3/ GND " " 2.5 " " " 6/ " -1.5 " " " 6/ " A " " " B " " " 20 20 100 100 A " " " QA QB QC QD VCC 13/ 7/ " " " 400 " 7/ " " " mA " " " 15 " MIL-M-38510/315D 0.4 V 5.5 V " " " " " " " " " " " " VIC ICC Max 2.0 V GND 3 4 5 6 7 8 9 10 11 12 13 14 VOH Unit Min Subgroup 7 Tc = +25C Symbol FuncTional tests 8/ 9 Tc = +25C 10 Tc = +125C 11 3014 " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " Cases E A, B, C, D Cases1/ 2 1 2 2 3 Test no. B 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 B 9/ A B B A B B B A B A B A B A B A B B B A B A B A B A B A B A B " " " " NC 4 NC 6 NC 8 9 10 12 13 14 16 12 13 14 18 19 20 Measured A terminal NC Limits Unit Min Max VCC RO(1) RO(2) QD QC GND QB QA 4.5 V " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A 9/ " " B " " A " " " " " " " " " " " " B " " " " " " " " " " " " " " " " A 9/ " " " " " " X B " " " " " " " " " A " " " " " " " " " " " " " " " " " L " " " " " " " " " " " " H " " " " L " " " " " " H " " " " " L " " " " L " " " " " " " " " " H H L " " " H L " " " " H H L " " " H H L " " " " GND " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " L " " " " H L " " H H L " " " H H L " " " H H L " " " H H L " " " " " " L " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " H H L B 9/ " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " " A B A B OUT IN 12/ A to QA 29 IN IN A to QC A to QC B to QD B to QD A to QA 3 " " " 29 53 58 37 50 ns " " " MHz A to QC A to QC B to QD B to QD 3 " " " 74 81 52 56 ns " " " MIL-M-38510/315D 121 8 MIL-STD883 method TABLE III. Group A inspection for device type 10- Continued. Terminal conditions (pins not designated may be high 2.0 V; or low 0.7 V; or open). 3 4 5 6 7 8 9 10 11 See 10/ Same tests, terminal conditions, and limits as for subgroup 7, except TC = +125C and -55C. FMAX 3003 66 tPLH1 tPHL1 tPLH2 tPHL2 FMAX (Fig 11) " " " " 67 68 69 70 71 tPLH1 tPHL1 tPLH2 tPHL2 " " " " 72 73 74 75 IN IN IN IN 5.0 V GND " " " " " 11/ GND 11/ GND GND A 9/ " " " " 11/ GND 11/ GND A 9/ Same tests, terminal conditions, and limits as for subgroup 10, except TC = -55C. See footnotes at end of device type 10. GND A 9/ A 9/ OUT OUT OUT OUT OUT OUT OUT OUT " " " " " " " " " OUT IN 12/ IN IN MHz 1/ Case 2, pins not referenced are N/C. 2/ Apply 4.5 volts pulse, then ground prior to taking measurements to set device in the desired state. Maintain ground for measurement. 3/ Input pulse must be applied one time after RO pulse. 4/ Input pulse must be applied twice after RO pulse. 5/ Input pulse must be applied four times after RO pulse. 6/ IIL limits (mA) min/max values for circuits shown: Parameter B C D E F RO(1) RO(2) -.12/-.36 " -.03/-.40 -.03/-.40 -.03/-.40 -.12/-.36 " " " " IIL2 A -0.5/-2.0 -1.0/-2.4 -1.0/-2.4 -1.0/-2.4 -0.5/-2.0 IIL3 B -0.7/-3.2 -0.7/-3.2 -0.7/-3.2 -0.4/-1.6 -0.7/-3.2 G 122 MIL-M-38510/315D A IIL1 7/ Circuits Terminals IOS limits (mA) min/max values for circuits shown: Parameter IOS Measured terminals QA, QB, QC, QD Circuits A B C D -15/-100 -15/-100 -30/-130 -15/-100 8/ Only a summary of attributes data is required. 9/ A = 3.0 V minimum; B = 0.0 V or GND. E F -15/-100 10/ H > 1.5 V; L < 1.5 V; X = don't care. 11/ Momentary 3.0 V (min), then ground. Maintain ground for measurement. 12/ FMAX min limit specified is the frequency of the input pulse. The output frequency shall be one-half of the input frequency. 13/ The minimum limit for circuit F shall be -150 A. G MIL-M-38510/315D 5. PACKAGING 5.1 Packaging requirements. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When actual packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Point's packaging activity within the Military Service or Defense Agency, or within the military service's system command. Packaging data retrieval is available from the managing Military Department's or Defense Agency's automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Microcircuits conforming to this specification are intended for original equipment design applications and logistic support of existing equipment. 6.2 Acquisition requirements. Acquisition documents should specify the following: a. Title, number, and date of the specification. b. PIN and compliance identifier, if applicable (see 1.2). c. Requirements for delivery of one copy of the conformance inspection data pertinent to the device inspection lot to be supplied with each shipment by the device manufacturer, if applicable. d. Requirements for certificate of compliance, if applicable. e. Requirements for notification of change of product or process to contracting activity in addition to notification to the qualifying activity, if applicable. f. Requirements for failure analysis (including required test condition of method 5003 of MIL-STD-883), corrective action, and reporting of results, if applicable. g. Requirements for product assurance options. h. Requirements for special carriers, lead lengths, or lead forming, if applicable. These requirements shall not affect the part number. Unless otherwise specified, these requirements will not apply to direct purchase by or direct shipment to the Government. I Requirements for "JAN" marking. j. Packaging Requirements (see 5.1) 6.3 Superseding information. The requirements of MIL-M-38510 have been superseded to take advantage of the available Qualified Manufacturer Listing (QML) system provided by MIL-PRF-38535. Previous references to MIL-M38510 in this document have been replaced by appropriate references to MIL-PRF-38535. All technical requirements now consist of this specification and MIL-PRF-38535. The MIL-M-38510 specification sheet number and PIN have been retained to avoid adversely impacting existing government logistics systems and contractor's parts lists. 6.4 Qualification. With respect to products requiring qualification, awards will be made only for products which are, at the time of award of contract, qualified for inclusion in Qualified Manufacturers List QML-38535 whether or not such products have actually been so listed by that date. The attention of the contractors is called to these requirements, and manufacturers are urged to arrange to have the products that they propose to offer to the Federal Government tested for qualification in order that they may be eligible to be awarded contracts or purchase orders for the products covered by this specification. Information pertaining to qualification of products may be obtained from DSCC-VQ, 3990 E. Broad Street, Columbus, Ohio 43123-1199. 123 MIL-M-38510/315D 6.5 Abbreviations, symbols, and definitions. The abbreviations, symbols, and definitions used herein are defined in MIL-PRF-38535, MIL-HDBK-1331, and as follows: GND ........................................... IIN ................................................ VIC ............................................... VIN ............................................... Ground zero voltage potential Current flowing into an input terminal Input clamp voltage Voltage level at an input terminal 6.6 Logistic support. Lead materials and finishes (see 3.4) are interchangeable. Unless otherwise specified, microcircuits acquired for Government logistic support will be acquired to device class B (see 1.2.2), lead material and finish A (see 3.4). Longer length leads and lead forming should not affect the part number. 6.7 Substitutability. The cross-reference information below is presented for the convenience of users. Microcircuits covered by this specification will functionally replace the listed generic-industry type. Generic-industry microcircuit types may not have equivalent operational performance characteristics across military temperature ranges or reliability factors equivalent to MIL-M-38510 device types and may have slight physical variations in relation to case size. The presence of this information should not be deemed as permitting substitution of generic-industry types for MIL-M-38510 types or as a waiver of any of the provisions of MIL-PRF-38535. Military device type____ Generic-industry type_____ 01 02 03 04 05 06 07 08 09 10 11 12 13 54LS90 54LS93 54LS160 54LS161 54LS168 54LS169 54LS192 54LS193 54LS191 54LS92 54LS162 54LS163 54LS190 124 MIL-M-38510/315D 6.8 Manufacturers' designation. Manufacturers' circuits which form a part of this specification are designated with an "X" as shown in table IV herein. TABLE IV. Manufacturers' designation. Device type Circuit A B G C E F D Manufacturer Texas Instruments, Incorporated Signetics Corp. National SemiConductor Corp. Raytheon Company Fairchild Semiconductor Motorola, Inc. Advanced Micro Devices Inc. X X X Commercial Type 01 54LS90 X X 02 54LS93 X X X X X X 03 54LS160A X X X X X X X 04 54LS161A X X X X X X X 05 54LS168 X X 06 54LS169A X X 07 54LS192 X X X X X X X 08 54LS193 X X X X X X X 09 54LS191 X X X X X X X 10 54LS92 X X X 11 54LS162A X X X X X X X 12 54LS163A X X X X X X X 13 54LS190 X X X X X X X X 6.9 Change from previous issue. Asterisks are not used in this revision to identify changes with respect to the previous issue, due to the extensiveness of the changes. 125 MIL-M-38510/315D Custodians: Army - CR Navy - EC Air Force - 11 DLA - CC Preparing activity: DLA - CC Review activities: Army - SM, MI Navy - AS, CG, MC, SH TD Air Force - 03, 19, 99 (Project 5962-1996) 126