www.RFM.com E-mail: info@rfm.com Page 1 of 4
©2009 by RF Monolithics, Inc. SF2135A - 7/9/09
Electrical Characteristics
Characteristic Sym Notes Min Typ Max Units
Center Frequency fC196.0 MHz
1 dB Bandwidth BW11.56 1.80 MHz
Insertion Loss IL 1, 2,3 11.8 15.0 dB
Relative Attenuation 91 to 94.5 MHz 6 9.5
97.5 to 98.5 MHz 6 11.5 dB
10 to 60 MHz 55 72 dB
76.8 MHz 55 72 dB
132 to135 MHz 55 74 dB
135 to 1000 MHz 35 58
Passband Amplitude Ripple 95.2 to 96.8 MHz 1, 2, 3 0.9 1.2 dBP-P
Group Delay Ripple 95.2 to 96.8 MHz 62 100 nsP-P
Operating Temperature 1 -30 +85 °C
Terminating Source Impedance 50 ohm
Terminating Load Impedance 50 ohm
Impedance Matching to 50 Unbalanced External L-C
Case Style SMP-53 13.3 x 6.5 mm Nominal Footprint
Lid Symbolization (YY = year, WW = week) RF M SF2135A YYWW
Designed for Wide Channel IF Filtering
Low Insertion Loss
Hermetic 13.3 x 6.5 mm Surface-mount Case
Balanced or Single-ended Input and Output
Complies with Directive 2002/95/EC (RoHS)
Absolute Maximum Ratings
Rating Value Units
Maximum Incident Power in Passband +13 dBm
Maximum DC Voltage Between any Two Ter minals 30 VDC
Storage Temperature Range -40 to +85 °C
Suitable for Lead-free Soldering - Maximum Soldering Profile 260 °C for 30 s
96.0 MHz
SAW Filter
SF2135A
SMP-53
1. Unless note d other wise , all s pecific ations ap ply over t he o peratin g temper at ure range with f ilt er sol dere d to th e spec ified d emons trat ion board wit h impe dance
match ing to 50 and measured with 50 network analyzer.
2. Unless noted otherwise, all freque ncy specifications are referenced to the nominal center frequency, fc.
3. Rejection i s measured as atten uation below the minimum IL point in th e pas sband. Rejecti on in final user ap plication is dependent on P CB l ay out a nd ext erna l
impedance matching des ign. See Application Note No. 42 for details.
4. Part to part absolute delay meas urement records the absolute delay mean across 1 dB passban d.
5. "LRIP" or "L" after the part number indicates "low rate initial production" and " ENG" or "E" indicates "engineering prototypes.”
6. The desi gn, manufact uring process, and specifications of this filter are subject to change.
7. Eith er Port 1 or Por t 2 may be used f or either inpu t o r ou tp ut in t he d esign. Ho wever, impedanc es and imped ance matchi ng ma y vary bet ween Por t 1 and Por t
2, so that the filter must always be installed in one dir ection per the circuit design .
8. US and international patents may apply.
Pb
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling.
Notes:
www.RFM.com E-mail: info@rfm.com Page 2 of 4
©2009 by RF Monolithics, Inc. SF2135A - 7/9/09
CH1 S21 DEL 100 ns/ REF 1.5 us
CH1 CENTER 96 . 000 000 MHz SPAN 4. 000 000 MHz
Cor
Smo
PRm
CH2 S21 LOG 10 dB/ REF -43 dB
CH2 CENTER 96 . 000 000 MHz SPAN 30 . 000 000 MHz
Cor
PRm
2 Mar 20 07 06:33: 48
1
2
3
2:-71 .859 ns 1.600 000 MHz
REF=1
CH1 Markers
mean : 1 . 4732 us
s . dev : 13 . 558 ns
p-p : 71 . 859 ns
1
1 : -11 . 432 dB 95 . 568 750 MHz
Max
SF2 135A TST Demo
Thru c al
Resp
Resp
SF2135A 50 ohm Tuning Network
SF2135A Group Delay Ripple and Filter Response Plots
SF2135A
www.RFM.com E-mail: info@rfm.com Page 3 of 4
©2009 by RF Monolithics, Inc. SF2135A - 7/9/09
CH1 S11 1 U FS
CENTR 96 . 000 MHz SPAN 4. 000 MHz
Cor
PRm
CH2 S21 LO G 1 dB/ REF -13 dB
START 94 . 000 000 MHz STOP 98 . 000 000 MHz
Cor
PRm
CH3 S22 1 U FS
CENTR 96 . 000 MHz SPAN 4. 000 MHz
Cor
8 Mar 2007 09: 46: 34
1
1: 101 .74 28 . 777 47 . 709 nH
96 . 000 000 MHz
1
2
3 4
1: 0. 0000 dB 0. 000 000 MHz
Max RE F=1
CH2 Markers
BW: 1. 778417 MHz
cent : 95 . 932649 MHz
Q: 53 . 943
1_loss : -11 . 634 dB
1
1: 49.668 0. 1367 226 . 66 pH
96 . 000 000 MHz
SF2135 A TST Demo
Full 2-p ort cal
Full
Full
SF2135A S11, S22 and Pass-band Plots
www.RFM.com E-mail: info@rfm.com Page 4 of 4
©2009 by RF Monolithics, Inc. SF2135A - 7/9/09
SAW Filters Package
SMP-53 Case
12-Terminal Ceramic Surface-Mount Case
13.3 x 6.5 mm Nominal Footprint
Case Dimensions
Dimension mm Inches
Min Nom Max Min Nom Max
A13.08 13.31 13.60 0.515 0.524 0.535
B6.27 6.50 6.80 0.247 0.256 0.268
C1.91 2.00 0.075 0.079
D1.50 0.059
E0.79 0.031
H1.0 0.039
P2.54 0.100
Electrical Connections
Connection Terminals
Port 1 Input or Return 11
Return or Input 12
Port 2 Output or Return 5
Return or Output 6
Ground All others
Single-ended Operation Return is ground
Diff erential Operation Return is hot
Materials
Solder Pad
Plating 0.3 to 1.0 µm Gold over 1.27 to 8.89 µm Nickel
Lid Plating 2.0 to 3.0 µm Nickel
Body Al2O3 Ceramic
Pb Free
C
H
P (8 Places)
E (10 Places)
D
B
A
1
2
3
4
10
9
8
7
12
65
11
10
9
8
7
1
2
3
4
11
12
56
TOP VIEW BOTTOM VIEW