TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com 0.5-A 60-V STEP-DOWN SWIFTTM DC/DC CONVERTER WITH Eco-modeTM FEATURES 1 * * * * * * * * * * Qualified for Automotive Applications 3.5-V to 60-V Input Voltage Range 200-m High-Side MOSFET High Efficiency at Light Loads with a Pulse Skipping Eco-modeTM Control Scheme 116-A Operating Quiescent Current 1.5-A Shutdown Current 100-kHz to 2.5-MHz Switching Frequency Synchronizes to External Clock Adjustable Slow Start/Sequencing Undervoltage and Overvoltage Power Good Output * * * * Adjustable UVLO Voltage and Hysteresis 0.8-V Internal Voltage Reference Supported by SwitcherProTM Software Tool (http://focus.ti.com/docs/toolsw/folders/print/s witcherpro.html) For SWIFTTM Documentation, See the TI Website at http://www.ti.com/swift APPLICATIONS * * 12-V, 24-V and 48-V Industrial and Commercial Low Power Systems Aftermarket Auto Accessories: Video, GPS, Entertainment DESCRIPTION The TPS57060-Q1 device is a 60-V 0.5-A step-down regulator with an integrated high-side MOSFET. Current-mode control provides simple external compensation and flexible component selection. A low-ripple pulse-skip mode reduces the no load, regulated output supply current to 116 A. Using the enable pin, shutdown supply current is reduced to 1.5 A, when the enable pin is low. Under voltage lockout is internally set at 2.5 V, but can be increased using the enable pin. The output voltage startup ramp is controlled by the slow start pin that can also be configured for sequencing/tracking. An open-drain power good signal indicates the output is within 92% to 109% of its nominal voltage. A wide switching frequency range allows efficiency and external component size to be optimized. Frequency fold back and thermal shutdown protects the part during an overload condition. The TPS57060-Q1 is available in a 10-pin thermally enhanced MSOP PowerPADTM package (DGQ) and a SON (DRC) package. SIMPLIFIED SCHEMATIC VIN EFFICIENCY vs LOAD CURRENT PWRGD 100 TPS57060-Q1 90 BOOT PH SS /TR RT /CLK COMP Efficiency - % 80 EN 70 60 50 40 30 VI = 12 V, VO = 3.3 V, fsw = 500 kHz 20 VSENSE 10 0 0 GND 0.05 0.1 0.15 0.2 0.25 0.3 0.35 Load Current - A 0.4 0.45 0.5 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2010, Texas Instruments Incorporated TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. ORDERING INFORMATION (1) PACKAGE (2) TJ -40C to 150C (1) (2) ORDERABLE PART NUMBER TOP-SIDE MARKING MSOP - DGQ Reel of 2500 TPS57060QDGQRQ1 5706Q SON - DRC Reel of 3000 TPS57060QDRCRQ1 5706Q For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI web site at www.ti.com. Package drawings, thermal data, and symbolization are available at www.ti.com/packaging. ABSOLUTE MAXIMUM RATINGS (1) Over operating temperature range (unless otherwise noted). VALUE VIN -0.3 V to 65 V EN (2) -0.3 V to 5 V BOOT Input voltage 73 V VSENSE -0.3 V to 3 V COMP -0.3 V to 3 V PWRGD -0.3 V to 6 V -0.3 V to 3 V SS/TR -0.3 V to 3.6 V RT/CLK BOOT-PH 8V -0.6 V to 65 V Output voltage PH 200ns -1 V to 65 V 30ns -2 V to 65 V Maximum dc voltage, Tj=-40C Voltage difference Source current PAD to GND EN 100 A BOOT 100 mA VSENSE PH RT/CLK VIN Sink current -0.85V 200 mV 10 A Current Limit 100 A Current Limit COMP 100 A PWRGD 10 mA SS/TR 200 A Operating junction temperature -40 C to 150 C Storage temperature -65 C to 150 C (1) (2) 2 Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. See Enable and Adjusting Undervoltage Lockout for details. Submit Documentation Feedback Copyright (c) 2010, Texas Instruments Incorporated TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com THERMAL INFORMATION TPS57060-Q1 THERMAL METRIC (1) (2) JA DGQ DRC 10 PINS 10 PINS 62.5 56.5 Junction-to-ambient thermal resistance (standard board) (3) JA Junction-to-ambient thermal resistance (custom board) 57 61.5 JCtop Junction-to-case (top) thermal resistance 83 52.1 JB Junction-to-board thermal resistance 28 20.6 JT Junction-to-top characterization parameter 1.7 0.9 JB Junction-to-board characterization parameter 20.1 20.8 JCbot Junction-to-case (bottom) thermal resistance 21 5.2 (1) (2) (3) UNITS C/W For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953. Power rating at a specific ambient temperature TA should be determined with a junction temperature of 150C. This is the point where distortion starts to substantially increase. See power dissipation estimate in application section of this data sheet for more information. Test boards conditions: (a) 3 inches x 3 inches, 2 layers, thickness: 0.062 inch (b) 2 oz. copper traces located on the top of the PCB (c) 2 oz. copper ground plane, bottom layer (d) 6 thermal vias (13mil) located under the device package ELECTRICAL CHARACTERISTICS TJ = -40C to 150C, VIN = 3.5 to 60V (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT SUPPLY VOLTAGE (VIN PIN) Operating input voltage 3.5 60 Internal undervoltage lockout threshold No voltage hysteresis, rising and falling 2.5 Shutdown supply current EN = 0 V, 25C, 3.5 V VIN 60 V 1.5 4 Operating : nonswitching supply current VSENSE = 0.83 V, VIN = 12 V, 25C 116 136 1.25 1.36 V V A ENABLE AND UVLO (EN PIN) Enable threshold voltage Input current No voltage hysteresis, rising and falling, 25C 1.15 Enable threshold +50 mV -3.8 Enable threshold -50 mV -0.9 A -2.9 Hysteresis current V A VOLTAGE REFERENCE Voltage reference TJ = 25C 0.792 0.8 0.808 0.784 0.8 0.816 V HIGH-SIDE MOSFET On-resistance VIN = 3.5 V, BOOT-PH = 3 V 300 VIN = 12 V, BOOT-PH = 6 V 200 410 m ERROR AMPLIFIER Input current 50 nA Error amplifier transconductance (gM) -2 A < ICOMP < 2 A, VCOMP = 1 V 97 Mhos Error amplifier transconductance (gM) -2 A < ICOMP < 2 A, VCOMP = 1 V, during slow start VVSENSE = 0.4 V 26 Mhos Error amplifier dc gain VVSENSE = 0.8 V Error amplifier bandwidth Error amplifier source/sink V(COMP) = 1 V, 100 mV overdrive COMP to switch current transconductance 10,000 V/V 2700 kHz 7 A 1.9 A/V 0.94 A CURRENT LIMIT Current limit threshold Copyright (c) 2010, Texas Instruments Incorporated VIN = 12 V, TJ = 25C 0.6 Submit Documentation Feedback 3 TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com ELECTRICAL CHARACTERISTICS (continued) TJ = -40C to 150C, VIN = 3.5 to 60V (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT THERMAL SHUTDOWN Thermal shutdown 4 Submit Documentation Feedback 182 C Copyright (c) 2010, Texas Instruments Incorporated TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com ELECTRICAL CHARACTERISTICS (continued) TJ = -40C to 150C, VIN = 3.5 to 60V (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT 2500 kHz 720 kHz 2200 kHz TIMING RESISTOR AND EXTERNAL CLOCK (RT/CLK PIN) fSW Switching frequency using RT mode VIN = 12 V 100 Switching frequency VIN = 12 V, RT = 200 k 450 Switching frequency using CLK mode VIN = 12 V 581 300 Minimum CLK input pulse width 40 RT/CLK high threshold VIN = 12 V RT/CLK low threshold VIN = 12 V RT/CLK falling edge to PH rising edge delay Measured at 500 kHz with RT resistor in series PLL lock in time Measured at 500 kHz 1.9 0.45 ns 2.2 V 0.7 V 60 ns 100 s SLOW START AND TRACKING (SS/TR) Charge current VSS/TR = 0.4 V 2 A SS/TR-to-VSENSE matching VSS/TR = 0.4 V 45 mV SS/TR-to-reference crossover 98% nominal 1.0 V SS/TR discharge current (overload) VSENSE = 0 V, V(SS/TR) = 0.4 V 112 A SS/TR discharge voltage VSENSE = 0 V 54 mV VSENSE falling 92% POWER GOOD (PWRGD PIN) VVSENSE VSENSE rising 94% VSENSE rising 109% VSENSE falling 107% Hysteresis VSENSE falling 2% Output high leakage VSENSE = VREF, V(PWRGD) = 5.5 V, 25C 10 nA On resistance I(PWRGD) = 3 mA, VSENSE < 0.79 V 50 Minimum VIN for defined output V(PWRGD) < 0.5 V, II(PWRGD) = 100 A VSENSE threshold Copyright (c) 2010, Texas Instruments Incorporated 0.95 1.5 Submit Documentation Feedback V 5 TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com DEVICE INFORMATION PIN CONFIGURATION MSOP10 (TOP VIEW) BOOT 1 VIN 2 10 Thermal Pad (11) PH 9 GND 8 COMP EN 3 SS/TR 4 7 VSENSE RT/CLK 5 6 PWRGD PIN FUNCTIONS PIN I/O DESCRIPTION NAME NO. BOOT 1 O A bootstrap capacitor is required between BOOT and PH. If the voltage on this capacitor is below the minimum required by the output device, the output is forced to switch off until the capacitor is refreshed. COMP 8 O Error amplifier output, and input to the output switch current comparator. Connect frequency compensation components to this pin. EN 3 I Enable pin, internal pull-up current source. Pull below 1.2V to disable. Float to enable. Adjust the input undervoltage lockout with two resistors. GND 9 - Ground PH 10 I The source of the internal high-side power MOSFET. POWERPAD 11 - GND pin must be electrically connected to the exposed pad on the printed circuit board for proper operation. PWRGD 6 O An open drain output, asserts low if output voltage is low due to thermal shutdown, dropout, over-voltage or EN shut down. RT/CLK 5 I Resistor Timing and External Clock. An internal amplifier holds this pin at a fixed voltage when using an external resistor to ground to set the switching frequency. If the pin is pulled above the PLL upper threshold, a mode change occurs and the pin becomes a synchronization input. The internal amplifier is disabled and the pin is a high impedance clock input to the internal PLL. If clocking edges stop, the internal amplifier is re-enabled and the mode returns to a resistor set function. SS/TR 4 I Slow-start and Tracking. An external capacitor connected to this pin sets the output rise time. Since the voltage on this pin overrides the internal reference, it can be used for tracking and sequencing. VIN 2 I Input supply voltage, 3.5 V to 60 V. VSENSE 7 I Inverting node of the transconductance ( gm) error amplifier. 6 Submit Documentation Feedback Copyright (c) 2010, Texas Instruments Incorporated TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com FUNCTIONAL BLOCK DIAGRAM PWRGD 6 EN 3 VIN 2 Shutdown UV Thermal Shutdown Enable Comparator Logic UVLO Shutdown Shutdown Logic OV Enable Threshold Boot Charge Voltage Reference Boot UVLO Minimum Clamp Pulse Skip ERROR AMPLIFIER PWM Comparator VSENSE 7 Current Sense 1 BOOT Logic And PWM Latch SS/TR 4 Shutdown Slope Compensation 10 PH COMP 8 Overload Recovery Maximum Clamp Frequency Shift 11 POWERPAD Oscillator with PLL 9 GND 5 RT/CLK Copyright (c) 2010, Texas Instruments Incorporated Submit Documentation Feedback 7 TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com TYPICAL CHARACTERISTICS VOLTAGE REFERENCE vs JUNCTION TEMPERATURE 0.816 500 VI = 12 V VI = 12 V 375 Vref - Voltage Reference - V RDSON - Static Drain-Source On-State Resistance - mW ON RESISTANCE vs JUNCTION TEMPERATURE BOOT-PH = 3 V 250 BOOT-PH = 6 V 125 0 -50 0.808 0.800 0.792 0.784 -50 -25 0 25 50 75 100 TJ - Junction Temperature - C 125 -25 0 150 25 50 75 100 TJ - Junction Temperature - C 125 150 Figure 1. Figure 2. SWITCH CURRENT LIMIT vs JUNCTION TEMPERATURE SWITCHING FREQUENCY vs JUNCTION TEMPERATURE 1.1 610 VI = 12 V, RT = 200 kW VI = 12 V fs - Switching Frequency - kHz 600 Switch Current - A 1 0.9 0.8 590 580 570 560 0.7 -50 -25 0 25 50 75 100 125 550 -50 150 -25 0 TJ - Junction Temperature - C 25 50 75 100 TJ - Junction Temperature - C Figure 4. SWITCHING FREQUENCY vs RT/CLK RESISTANCE HIGH FREQUENCY RANGE SWITCHING FREQUENCY vs RT/CLK RESISTANCE LOW FREQUENCY RANGE 2500 500 2000 fs - Switching Frequency - kHz fs - Switching Frequency - kHz 150 Figure 3. VI = 12 V, TJ = 25C 1500 1000 500 0 0 25 50 75 100 125 RT/CLK - Resistance - kW Figure 5. 8 125 Submit Documentation Feedback 150 175 200 VI = 12 V, TJ = 25C 400 300 200 100 0 200 300 400 500 600 700 800 900 RT/CLK - Resistance - kW 1000 1100 1200 Figure 6. Copyright (c) 2010, Texas Instruments Incorporated TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com TYPICAL CHARACTERISTICS (continued) EA TRANSCONDUCTANCE DURING SLOW START vs JUNCTION TEMPERATURE EA TRANSCONDUCTANCE vs JUNCTION TEMPERATURE 150 40 VI = 12 V VI = 12 V 130 gm - mA/V gm - mA/V 30 110 90 20 70 10 -50 -25 0 25 50 75 100 TJ - Junction Temperature - C 125 50 -50 150 -25 0 25 50 75 100 125 150 TJ - Junction Temperature - C Figure 7. Figure 8. EN PIN VOLTAGE vs JUNCTION TEMPERATURE EN PIN CURRENT vs JUNCTION TEMPERATURE 1.40 -3.25 VI = 12 V, VI(EN) = Threshold +50 mV VI = 12 V -3.5 I(EN) - mA EN - Threshold - V 1.30 -3.75 1.20 -4 1.10 -50 -25 0 25 50 75 100 125 150 -4.25 -50 0 25 50 75 100 125 150 TJ - Junction Temperature - C Figure 9. Figure 10. EN PIN CURRENT vs JUNCTION TEMPERATURE SS/TR CHARGE CURRENT vs JUNCTION TEMPERATURE -1 -0.8 VI = 12 V, VI(EN) = Threshold -50 mV VI = 12 V -0.85 -1.5 I(SS/TR) - mA I(EN) - mA -25 TJ - Junction Temperature - C -0.9 -0.95 -1 -50 -2 -2.5 -25 0 25 50 75 100 TJ - Junction Temperature - C Figure 11. Copyright (c) 2010, Texas Instruments Incorporated 125 150 -3 -50 -25 0 25 50 75 100 TJ - Junction Temperature - C 125 150 Figure 12. Submit Documentation Feedback 9 TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com TYPICAL CHARACTERISTICS (continued) SS/TR DISCHARGE CURRENT vs JUNCTION TEMPERATURE SWITCHING FREQUENCY vs VSENSE 120 100 VI = 12 V VI = 12 V, TJ = 25C 80 % of Nominal fsw II(SS/TR) - mA 115 110 60 40 105 20 100 -50 0 -25 0 25 50 75 100 TJ - Junction Temperature - C 125 150 0 SHUTDOWN SUPPLY CURRENT vs INPUT VOLTAGE (Vin) 2 TJ = 25C I(VIN) - mA 1.5 1 0.5 1 0.5 0 -25 0 25 50 75 100 TJ - Junction Temperature - C 125 150 0 10 20 30 40 VI - Input Voltage - V Figure 15. VIN SUPPLY CURRENT vs JUNCTION TEMPERATURE 60 VIN SUPPLY CURRENT vs INPUT VOLTAGE 140 VI = 12 V, VI(VSENSE) = 0.83 V o TJ = 25 C, VI(VSENSE) = 0.83 V 130 130 120 120 I(VIN) - mA I(VIN) - mA 50 Figure 16. 140 110 100 110 100 90 -25 0 25 50 75 100 TJ - Junction Temperature - C Figure 17. 10 0.8 SHUTDOWN SUPPLY CURRENT vs JUNCTION TEMPERATURE 1.5 90 -50 0.6 Figure 14. VI = 12 V I(VIN) - mA 0.4 VSENSE - V Figure 13. 2 0 -50 0.2 Submit Documentation Feedback 125 150 0 20 40 VI - Input Voltage - V 60 Figure 18. Copyright (c) 2010, Texas Instruments Incorporated TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com TYPICAL CHARACTERISTICS (continued) PWRGD ON RESISTANCE vs JUNCTION TEMPERATURE PWRGD THRESHOLD vs JUNCTION TEMPERATURE 115 100 VI = 12 V PWRGD Threshold - % of Vref VI = 12 V RDSON - W 80 60 40 20 VSENSE Rising 110 VSENSE Falling 105 100 VSENSE Rising 95 VSENSE Falling 90 0 -50 -25 0 25 50 75 100 125 85 -50 150 -25 0 150 Figure 20. BOOT-PH UVLO vs JUNCTION TEMPERATURE INPUT VOLTAGE (UVLO) vs JUNCTION TEMPERATURE 2.5 3 2.3 2.75 2 1.8 2.50 2.25 1.5 -50 -25 0 25 50 75 100 TJ - Junction Temperature - C 125 2 -50 150 -25 0 25 50 75 100 TJ - Junction Temperature - C Figure 21. 125 150 Figure 22. SS/TR TO VSENSE OFFSET vs VSENSE SS/TR TO VSENSE OFFSET vs TEMPERATURE 600 60 V(SS/TR) = 0.2 V VI = 12 V VIN = 12 V TJ = 25C 500 55 50 400 Offset - mV Offset Voltage Threshold (mV) 125 Figure 19. VI(VIN) - V VI(BOOT-PH) - V TJ - Junction Temperature - C 25 50 75 100 TJ - Junction Temperature - C 300 45 40 200 35 100 30 -50 0 0 200 400 600 Voltage Sense (mV) Figure 23. Copyright (c) 2010, Texas Instruments Incorporated 800 -25 0 25 50 75 100 125 150 TJ - Junction Temperature - C Figure 24. Submit Documentation Feedback 11 TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com OVERVIEW The TPS57060-Q1 device is a 60-V, 0.5-A, step-down (buck) regulator with an integrated high side n-channel MOSFET. To improve performance during line and load transients the device implements a constant frequency, current mode control which reduces output capacitance and simplifies external frequency compensation design. The wide switching frequency of 100kHz to 2500kHz allows for efficiency and size optimization when selecting the output filter components. The switching frequency is adjusted using a resistor to ground on the RT/CLK pin. The device has an internal phase lock loop (PLL) on the RT/CLK pin that is used to synchronize the power switch turn on to a falling edge of an external system clock. The TPS57060-Q1 has a default start up voltage of approximately 2.5V. The EN pin has an internal pull-up current source that can be used to adjust the input voltage under voltage lockout (UVLO) threshold with two external resistors. In addition, the pull up current provides a default condition. When the EN pin is floating the device will operate. The operating current is 116A when not switching and under no load. When the device is disabled, the supply current is 1.5A. The integrated 200m high side MOSFET allows for high efficiency power supply designs capable of delivering 0.5 amperes of continuous current to a load. The TPS57060-Q1 reduces the external component count by integrating the boot recharge diode. The bias voltage for the integrated high side MOSFET is supplied by a capacitor on the BOOT to PH pin. The boot capacitor voltage is monitored by an UVLO circuit and will turn the high side MOSFET off when the boot voltage falls below a preset threshold. The TPS57060-Q1 can operate at high duty cycles because of the boot UVLO. The output voltage can be stepped down to as low as the 0.8V reference. The TPS57060-Q1 has a power good comparator (PWRGD) which asserts when the regulated output voltage is less than 92% or greater than 109% of the nominal output voltage. The PWRGD pin is an open drain output which deasserts when the VSENSE pin voltage is between 94% and 107% of the nominal output voltage allowing the pin to transition high when a pull-up resistor is used. The TPS57060-Q1 minimizes excessive output overvoltage (OV) transients by taking advantage of the OV power good comparator. When the OV comparator is activated, the high side MOSFET is turned off and masked from turning on until the output voltage is lower than 107%. The SS/TR (slow start/tracking) pin is used to minimize inrush currents or provide power supply sequencing during power up. A small value capacitor should be coupled to the pin to adjust the slow start time. A resistor divider can be coupled to the pin for critical power supply sequencing requirements. The SS/TR pin is discharged before the output powers up. This discharging ensures a repeatable restart after an over-temperature fault, UVLO fault or a disabled condition. The TPS57060-Q1, also, discharges the slow start capacitor during overload conditions with an overload recovery circuit. The overload recovery circuit will slow start the output from the fault voltage to the nominal regulation voltage once a fault condition is removed. A frequency foldback circuit reduces the switching frequency during startup and overcurrent fault conditions to help control the inductor current. 12 Submit Documentation Feedback Copyright (c) 2010, Texas Instruments Incorporated TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com DETAILED DESCRIPTION Fixed Frequency PWM Control The TPS57060-Q1 uses an adjustable fixed frequency, peak current mode control. The output voltage is compared through external resistors on the VSENSE pin to an internal voltage reference by an error amplifier which drives the COMP pin. An internal oscillator initiates the turn on of the high side power switch. The error amplifier output is compared to the high side power switch current. When the power switch current reaches the level set by the COMP voltage, the power switch is turned off. The COMP pin voltage will increase and decrease as the output current increases and decreases. The device implements a current limit by clamping the COMP pin voltage to a maximum level. The Eco-ModeTM is implemented with a minimum clamp on the COMP pin. Slope Compensation Output Current The TPS57060-Q1 adds a compensating ramp to the switch current signal. This slope compensation prevents sub-harmonic oscillations. The available peak inductor current remains constant over the full duty cycle range. Pulse Skip Eco-Mode The TPS57060-Q1 operates in a pulse skip Eco mode at light load currents to improve efficiency by reducing switching and gate drive losses. The TPS57060-Q1 is designed so that if the output voltage is within regulation and the peak switch current at the end of any switching cycle is below the pulse skipping current threshold, the device enters Eco mode. This current threshold is the current level corresponding to a nominal COMP voltage or 500mV. When in Eco-mode, the COMP pin voltage is clamped at 500mV and the high side MOSFET is inhibited. Further decreases in load current or in output voltage can not drive the COMP pin below this clamp voltage level. Since the device is not switching, the output voltage begins to decay. As the voltage control loop compensates for the falling output voltage, the COMP pin voltage begins to rise. At this time, the high side MOSFET is enabled and a switching pulse initiates on the next switching cycle. The peak current is set by the COMP pin voltage. The output voltage re-charges the regulated value (see Figure 25), then the peak switch current starts to decrease, and eventually falls below the Eco mode threshold at which time the device again enters Eco mode. For Eco mode operation, the TPS57060-Q1 senses peak current, not average or load current, so the load current where the device enters Eco mode is dependent on the output inductor value. For example, the circuit in Figure 51 enters Eco mode at about 20 mA of output current. When the load current is low and the output voltage is within regulation, the device enters a sleep mode and draws only 116A input quiescent current. The internal PLL remains operating when in sleep mode. When operating at light load currents in the pulse skip mode, the switching transitions occur synchronously with the external clock signal. Copyright (c) 2010, Texas Instruments Incorporated Submit Documentation Feedback 13 TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com DETAILED DESCRIPTION (continued) VOUT(ac) IL PH Figure 25. Pulse Skip Mode Operation Low Dropout Operation and Bootstrap Voltage (BOOT) The TPS57060-Q1 has an integrated boot regulator, and requires a small ceramic capacitor between the BOOT and PH pins to provide the gate drive voltage for the high side MOSFET. The BOOT capacitor is refreshed when the high side MOSFET is off and the low side diode conducts. The value of this ceramic capacitor should be 0.1F. A ceramic capacitor with an X7R or X5R grade dielectric with a voltage rating of 10V or higher is recommended because of the stable characteristics overtemperature and voltage. To improve drop out, the TPS57060-Q1 is designed to operate at 100% duty cycle as long as the BOOT to PH pin voltage is greater than 2.1V. When the voltage from BOOT to PH drops below 2.1V, the high side MOSFET is turned off using an UVLO circuit which allows the low side diode to conduct and refresh the charge on the BOOT capacitor. Since the supply current sourced from the BOOT capacitor is low, the high side MOSFET can remain on for more switching cycles than are required to refresh the capacitor, thus the effective duty cycle of the switching regulator is high. The effective duty cycle during dropout of the regulator is mainly influenced by the voltage drops across the power MOSFET, inductor resistance, low side diode and printed circuit board resistance. During operating conditions in which the input voltage drops and the regulator is operating in continuous conduction mode, the high side MOSFET can remain on for 100% of the duty cycle to maintain output regulation, until the BOOT to PH voltage falls below 2.1V. 14 Submit Documentation Feedback Copyright (c) 2010, Texas Instruments Incorporated TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com DETAILED DESCRIPTION (continued) Attention must be taken in maximum duty cycle applications which experience extended time periods with light loads or no load. When the voltage across the BOOT capacitor falls below the 2.1V UVLO threshold, the high side MOSFET is turned off, but there may not be enough inductor current to pull the PH pin down to recharge the BOOT capacitor. The high side MOSFET of the regulator stops switching because the voltage across the BOOT capacitor is less than 2.1V. The output capacitor then decays until the difference in the input voltage and output voltage is greater than 2.1V, at which point the BOOT UVLO threshold is exceeded, and the device starts switching again until the desired output voltage is reached. This operating condition persists until the input voltage and/or the load current increases. It is recommended to adjust the VIN stop voltage greater than the BOOT UVLO trigger condition at the minimum load of the application using the adjustable VIN UVLO feature with resistors on the EN pin. The start and stop voltages for typical 3.3V and 5V output applications are shown in Figure 26 and Figure 27. The voltages are plotted versus load current. The start voltage is defined as the input voltage needed to regulate the output within 1%. The stop voltage is defined as the input voltage at which the output drops by 5% or stops switching. During high duty cycle conditions, the inductor current ripple increases while the BOOT capacitor is being recharged resulting in an increase in ripple voltage on the output. This is due to the recharge time of the boot capacitor being longer than the typical high side off time when switching occurs every cycle. 4 5.6 VO = 3.3 V VO = 5 V 5.4 VI - Input Voltage - V VI - Input Voltage - V 3.8 3.6 Start 3.4 Stop 3.2 5.2 Start 5 Stop 4.8 3 4.6 0 0.05 0.10 IO - Output Current - A 0.15 Figure 26. 3.3V Start/Stop Voltage 0.20 0 0.05 0.10 IO - Output Current - A 0.15 0.20 Figure 27. 5.0V Start/Stop Voltage Error Amplifier The TPS57060-Q1 has a transconductance amplifier for the error amplifier. The error amplifier compares the VSENSE voltage to the lower of the SS/TR pin voltage or the internal 0.8V voltage reference. The transconductance (gm) of the error amplifier is 97A/V during normal operation. During the slow start operation, the transconductance is a fraction of the normal operating gm. When the voltage of the VSENSE pin is below 0.8V and the device is regulating using the SS/TR voltage, the gm is 25A/V. The frequency compensation components (capacitor, series resistor and capacitor) are added to the COMP pin to ground. Voltage Reference The voltage reference system produces a precise 2% voltage reference over temperature by scaling the output of a temperature stable bandgap circuit. Adjusting the Output Voltage The output voltage is set with a resistor divider from the output node to the VSENSE pin. It is recommended to use 1% tolerance or better divider resistors. Start with a 10 k for the R2 resistor and use the Equation 1 to calculate R1. To improve efficiency at light loads consider using larger value resistors. If the values are too high the regulator will be more susceptible to noise and voltage errors from the VSENSE input current will be noticeable Copyright (c) 2010, Texas Instruments Incorporated Submit Documentation Feedback 15 TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com DETAILED DESCRIPTION (continued) ae Vout - 0.8V o R1 = R2 c / 0.8 V e o (1) Enable and Adjusting Undervoltage Lockout The TPS57060-Q1 is disabled when the VIN pin voltage falls below 2.5 V. If an application requires a higher undervoltage lockout (UVLO), use the EN pin as shown in Figure 28 to adjust the input voltage UVLO by using the two external resistors. Though it is not necessary to use the UVLO adjust registers, for operation it is highly recommended to provide consistent power up behavior. The EN pin has an internal pull-up current source, I1, of 0.9A that provides the default condition of the TPS57060-Q1 operating when the EN pin floats. Once the EN pin voltage exceeds 1.25V, an additional 2.9A of hysteresis, Ihys, is added. This additional current facilitates input voltage hysteresis. Use Equation 2 to set the external hysteresis for the input voltage. Use Equation 3 to set the input start voltage. TPS57060-Q1 VIN Ihys I1 0.9 mA R1 2.9 mA + R2 EN - 1.25 V Figure 28. Adjustable Undervoltage Lockout (UVLO) V - VSTOP R1 = START IHYS R2 = (2) VENA VSTART - VENA + I1 R1 (3) Another technique to add input voltage hysteresis is shown in Figure 29. This method may be used, if the resistance values are high from the previous method and a wider voltage hysteresis is needed. The resistor R3 sources additional hysteresis current into the EN pin. TPS57060-Q1 VIN R1 Ihys I1 0.9 mA 2.9 mA + R2 EN 1.25 V R3 - VOUT Figure 29. Adding Additional Hysteresis 16 Submit Documentation Feedback Copyright (c) 2010, Texas Instruments Incorporated TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com DETAILED DESCRIPTION (continued) R1 = R2 = VSTART - VSTOP V IHYS + OUT R3 (4) VENA VSTART - VENA V + I1 - ENA R1 R3 (5) Do not place a low-impedance voltage source with greater than 5 V directly on the EN pin. Do not place a capacitor directly on the EN pin if VEN > 5 V when using a voltage divider to adjust the start and stop voltage. The node voltage, (see Figure 30) must remain equal to or less than 5.8 V. The zener diode can sink up to 100 A. The EN pin voltage can be greater than 5 V if the VIN voltage source has a high impedance and does not source more than 100 A into the EN pin. VIN IA RUVLO1 EN 10 kW Node 3 IB RUVLO2 IC 5.8 V UDG-10065 Figure 30. Node Voltage Copyright (c) 2010, Texas Instruments Incorporated Submit Documentation Feedback 17 TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com DETAILED DESCRIPTION (continued) Slow Start/Tracking Pin (SS/TR) The TPS57060-Q1 effectively uses the lower voltage of the internal voltage reference or the SS/TR pin voltage as the power-supply's reference voltage and regulates the output accordingly. A capacitor on the SS/TR pin to ground implements a slow start time. The TPS57060-Q1 has an internal pull-up current source of 2A that charges the external slow start capacitor. The calculations for the slow start time (10% to 90%) are shown in Equation 6. The voltage reference (VREF) is 0.8 V and the slow start current (ISS) is 2A. The slow start capacitor should remain lower than 0.47F and greater than 0.47nF. Tss(ms) Iss(m A) Css(nF) = Vref (V) 0.8 (6) At power up, the TPS57060-Q1 will not start switching until the slow start pin is discharged to less than 40 mV to ensure a proper power up, see Figure 31. Also, during normal operation, the TPS57060-Q1 will stop switching and the SS/TR must be discharged to 40 mV, when the VIN UVLO is exceeded, EN pin pulled below 1.25V, or a thermal shutdown event occurs. The VSENSE voltage will follow the SS/TR pin voltage with a 45mV offset up to 85% of the internal voltage reference. When the SS/TR voltage is greater than 85% on the internal reference voltage the offset increases as the effective system reference transitions from the SS/TR voltage to the internal voltage reference (see Figure 23). The SS/TR voltage will ramp linearly until clamped at 1.7V. EN SS/TR VSENSE VOUT Figure 31. Operation of SS/TR Pin when Starting Overload Recovery Circuit The TPS57060-Q1 has an overload recovery (OLR) circuit. The OLR circuit will slow start the output from the overload voltage to the nominal regulation voltage once the fault condition is removed. The OLR circuit will discharge the SS/TR pin to a voltage slightly greater than the VSENSE pin voltage using an internal pull down of 100A when the error amplifier is changed to a high voltage from a fault condition. When the fault condition is removed, the output will slow start from the fault voltage to nominal output voltage. 18 Submit Documentation Feedback Copyright (c) 2010, Texas Instruments Incorporated TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com DETAILED DESCRIPTION (continued) Sequencing Many of the common power supply sequencing methods can be implemented using the SS/TR, EN and PWRGD pins. The sequential method can be implemented using an open drain output of a power on reset pin of another device. The sequential method is illustrated in Figure 32 using two TPS57060-Q1 devices. The power good is coupled to the EN pin on the TPS57060-Q1 which will enable the second power supply once the primary supply reaches regulation. If needed, a 1nF ceramic capacitor on the EN pin of the second power supply will provide a 1ms start up delay. Figure 33 shows the results of Figure 32. TPS57060-Q1 EN PWRGD EN EN1 SS /TR SS /TR PWRGD1 PWRGD VOUT1 VOUT2 Figure 32. Schematic for Sequential Start-Up Sequence Figure 33. Sequential Startup using EN and PWRGD TPS57060-Q1 3 EN 4 SS/TR 6 PWRGD EN1, EN2 VOUT1 TPS57060-Q1 VOUT2 3 EN 4 SS/TR 6 PWRGD Figure 34. Schematic for Ratiometric Start-Up using Coupled SS/TR Pins Copyright (c) 2010, Texas Instruments Incorporated Figure 35. Ratio-Metric Startup using Coupled SS/TR pins Submit Documentation Feedback 19 TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com DETAILED DESCRIPTION (continued) Figure 34 shows a method for ratio-metric start up sequence by connecting the SS/TR pins together. The regulator outputs will ramp up and reach regulation at the same time. When calculating the slow start time the pull up current source must be doubled in Equation 6. Figure 35 shows the results of Figure 34. TPS57060-Q1 EN VOUT 1 SS/TR PWRGD TPS57060-Q1 VOUT 2 EN R1 SS/ TR R2 PWRGD R3 R4 Figure 36. Schematic for Ratiometric and Simultaneous Start-Up Sequence Ratio-metric and simultaneous power supply sequencing can be implemented by connecting the resistor network of R1 and R2 shown in Figure 36 to the output of the power supply that needs to be tracked or another voltage reference source. Using Equation 7 and Equation 8, the tracking resistors can be calculated to initiate the Vout2 slightly before, after or at the same time as Vout1. Equation 9 is the voltage difference between Vout1 and Vout2 at the 95% of nominal output regulation. The deltaV variable is zero volts for simultaneous sequencing. To minimize the effect of the inherent SS/TR to VSENSE offset (Vssoffset) in the slow start circuit and the offset created by the pullup current source (Iss) and tracking resistors, the Vssoffset and Iss are included as variables in the equations. To design a ratio-metric start up in which the Vout2 voltage is slightly greater than the Vout1 voltage when Vout2 reaches regulation, use a negative number in Equation 7 through Equation 9 for deltaV. Equation 9 will result in a positive number for applications which the Vout2 is slightly lower than Vout1 when Vout2 regulation is achieved. Since the SS/TR pin must be pulled below 40mV before starting after an EN, UVLO or thermal shutdown fault, careful selection of the tracking resistors is needed to ensure the device will restart after a fault. Make sure the calculated R1 value from Equation 7 is greater than the value calculated in Equation 10 to ensure the device can recover from a fault. As the SS/TR voltage becomes more than 85% of the nominal reference voltage the Vssoffset becomes larger as the slow start circuits gradually handoff the regulation reference to the internal voltage reference. The SS/TR pin voltage needs to be greater than 1.3V for a complete handoff to the internal voltage reference as shown in Figure 23. Vout2 + deltaV Vssoffset R1 = VREF Iss (7) VREF R1 R2 = Vout2 + deltaV - VREF (8) 20 Submit Documentation Feedback Copyright (c) 2010, Texas Instruments Incorporated TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com DETAILED DESCRIPTION (continued) deltaV = Vout1 - Vout2 R1 > 2800 Vout1 - 180 deltaV (9) (10) EN EN VOUT1 VOUT1 VOUT2 Figure 37. Ratiometric Startup with VOUT2 leading VOUT1 VOUT2 Figure 38. Ratiometric Startup with VOUT1 leading VOUT2 EN VOUT1 VOUT2 Figure 39. Simultaneous Startup With Tracking Resistor Copyright (c) 2010, Texas Instruments Incorporated Submit Documentation Feedback 21 TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com DETAILED DESCRIPTION (continued) Constant Switching Frequency and Timing Resistor (RT/CLK Pin) The switching frequency of the TPS57060-Q1 is adjustable over a wide range from approximately 100kHz to 2500kHz by placing a resistor on the RT/CLK pin. The RT/CLK pin voltage is typically 0.5V and must have a resistor to ground to set the switching frequency. To determine the timing resistance for a given switching frequency, use Equation 11 or the curves in Figure 40 or Figure 41. To reduce the solution size one would typically set the switching frequency as high as possible, but tradeoffs of the supply efficiency, maximum input voltage and minimum controllable on time should be considered. The minimum controllable on time is typically 130ns and limits the maximum operating input voltage. The maximum switching frequency is also limited by the frequency shift circuit. More discussion on the details of the maximum switching frequency is located below. 206033 RT (kOhm ) = | sw (kHz )1.0888 (11) SWITCHING FREQUENCY vs RT/CLK RESISTANCE HIGH FREQUENCY RANGE SWITCHING FREQUENCY vs RT/CLK RESISTANCE LOW FREQUENCY RANGE 2500 500 2000 fs - Switching Frequency - kHz fs - Switching Frequency - kHz VI = 12 V, TJ = 25C 1500 1000 500 0 0 25 50 75 100 125 150 RT/CLK - Clock Resistance - kW 175 200 Figure 40. High Range RT VI = 12 V, TJ = 25C 400 300 200 100 0 200 300 400 500 600 700 800 900 RT/CLK - Resistance - kW 1000 1100 1200 Figure 41. Low Range RT Overcurrent Protection and Frequency Shift The TPS57060-Q1 implements current mode control which uses the COMP pin voltage to turn off the high side MOSFET on a cycle by cycle basis. Each cycle the switch current and COMP pin voltage are compared, when the peak switch current intersects the COMP voltage, the high side switch is turned off. During overcurrent conditions that pull the output voltage low, the error amplifier will respond by driving the COMP pin high, increasing the switch current. The error amplifier output is clamped internally, which functions as a switch current limit. To increase the maximum operating switching frequency at high input voltages the TPS57060-Q1 implements a frequency shift. The switching frequency is divided by 8, 4, 2, and 1 as the voltage ramps from 0 to 0.8 volts on VSENSE pin. The device implements a digital frequency shift to enable synchronizing to an external clock during normal startup and fault conditions. Since the device can only divide the switching frequency by 8, there is a maximum input voltage limit in which the device operates and still have frequency shift protection. During short-circuit events (particularly with high input voltage applications), the control loop has a finite minimum controllable on time and the output has a low voltage. During the switch on time, the inductor current ramps to the peak current limit because of the high input voltage and minimum on time. During the switch off time, the inductor would normally not have enough off time and output voltage for the inductor to ramp down by the ramp up amount. The frequency shift effectively increases the off time allowing the current to ramp down. 22 Submit Documentation Feedback Copyright (c) 2010, Texas Instruments Incorporated TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com DETAILED DESCRIPTION (continued) Selecting the Switching Frequency The switching frequency that is selected should be the lower value of the two equations, Equation 12 and Equation 13. Equation 12 is the maximum switching frequency limitation set by the minimum controllable on time. Setting the switching frequency above this value will cause the regulator to skip switching pulses. Equation 13 is the maximum switching frequency limit set by the frequency shift protection. To have adequate output short circuit protection at high input voltages, the switching frequency should be set to be less than the fsw(maxshift) frequency. In Equation 13, to calculate the maximum switching frequency one must take into account that the output voltage decreases from the nominal voltage to 0 volts, the fdiv integer increases from 1 to 8 corresponding to the frequency shift. In Figure 42, the solid line illustrates a typical safe operating area regarding frequency shift and assumes the output voltage is zero volts, and the resistance of the inductor is 0.130, FET on resistance of 0.2 and the diode voltage drop is 0.5V. The dashed line is the maximum switching frequency to avoid pulse skipping. Enter these equations in a spreadsheet or other software or use the SwitcherPro design software to determine the switching frequency. ae 1 o ae (IL Rdc + VOUT + Vd) o fSW (max skip ) = c / / cc / e tON o e (VIN - IL Rhs + Vd) o (12) fSW (hift ) = fdiv ae (IL Rdc + VOUTSC + Vd) o c / t ON ce (VIN - IL x Rhs + Vd ) /o IL inductor current Rdc inductor resistance VIN maximum input voltage VOUT output voltage VOUTSC output voltage during short Vd diode voltage drop RDS(on) switch on resistance tON controllable on time DIV frequency divide equals (1, 2, 4, or 8) (13) 2500 fs - Switching Frequency - kHz VO = 3.3 V 2000 Shift 1500 Skip 1000 500 0 10 20 30 40 VI - Input Voltage - V 50 60 Figure 42. Maximum Switching Frequency vs. Input Voltage Copyright (c) 2010, Texas Instruments Incorporated Submit Documentation Feedback 23 TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com DETAILED DESCRIPTION (continued) How to Interface to RT/CLK Pin The RT/CLK pin can be used to synchronize the regulator to an external system clock. To implement the synchronization feature connect a square wave to the RT/CLK pin through the circuit network shown in Figure 43. The square wave amplitude must transition lower than 0.5V and higher than 2.2V on the RT/CLK pin and have an on time greater than 40 ns and an off time greater than 40 ns. The synchronization frequency range is 300 kHz to 2200 kHz. The rising edge of the PH will be synchronized to the falling edge of RT/CLK pin signal. The external synchronization circuit should be designed in such a way that the device will have the default frequency set resistor connected from the RT/CLK pin to ground should the synchronization signal turn off. It is recommended to use a frequency set resistor connected as shown in Figure 43 through a 50 resistor to ground. The resistor should set the switching frequency close to the external CLK frequency. It is recommended to ac couple the synchronization signal through a 10 pF ceramic capacitor to RT/CLK pin and a 4k series resistor. The series resistor reduces PH jitter in heavy load applications when synchronizing to an external clock and in applications which transition from synchronizing to RT mode. The first time the CLK is pulled above the CLK threshold the device switches from the RT resistor frequency to PLL mode. The internal 0.5V voltage source is removed and the CLK pin becomes high impedance as the PLL starts to lock onto the external signal. Since there is a PLL on the regulator the switching frequency can be higher or lower than the frequency set with the external resistor. The device transitions from the resistor mode to the PLL mode and then will increase or decrease the switching frequency until the PLL locks onto the CLK frequency within 100 microseconds. When the device transitions from the PLL to resistor mode the switching frequency will slow down from the CLK frequency to 150 kHz, then reapply the 0.5V voltage and the resistor will then set the switching frequency. The switching frequency is divided by 8, 4, 2, and 1 as the voltage ramps from 0 to 0.8 volts on VSENSE pin. The device implements a digital frequency shift to enable synchronizing to an external clock during normal startup and fault conditions. Figure 44, Figure 45 and Figure 46 show the device synchronized to an external system clock in continuous conduction mode (ccm) discontinuous conduction (dcm) and pulse skip mode (psm). TPS57060-Q1 10 pF 4 kW PLL Rfset EXT Clock Source 50 W RT/CLK Figure 43. Synchronizing to a System Clock 24 Submit Documentation Feedback Copyright (c) 2010, Texas Instruments Incorporated TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com DETAILED DESCRIPTION (continued) PH PH EXT EXT IL IL Figure 44. Plot of Synchronizing in ccm Figure 45. Plot of Synchronizing in dcm PH EXT IL Figure 46. Plot of Synchronizing in PSM Power Good (PWRGD Pin) The PWRGD pin is an open drain output. Once the VSENSE pin is between 94% and 107% of the internal voltage reference the PWRGD pin is de-asserted and the pin floats. It is recommended to use a pull-up resistor between the values of 10 and 100k to a voltage source that is 5.5V or less. The PWRGD is in a defined state once the VIN input voltage is greater than 1.5V but with reduced current sinking capability. The PWRGD will achieve full current sinking capability as VIN input voltage approaches 3V. Copyright (c) 2010, Texas Instruments Incorporated Submit Documentation Feedback 25 TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com DETAILED DESCRIPTION (continued) The PWRGD pin is pulled low when the VSENSE is lower than 92% or greater than 109% of the nominal internal reference voltage. Also, the PWRGD is pulled low, if the UVLO or thermal shutdown are asserted or the EN pin pulled low. Overvoltage Transient Protection The TPS57060-Q1 incorporates an overvoltage transient protection (OVTP) circuit to minimize voltage overshoot when recovering from output fault conditions or strong unload transients on power supply designs with low value output capacitance. For example, when the power supply output is overloaded the error amplifier compares the actual output voltage to the internal reference voltage. If the VSENSE pin voltage is lower than the internal reference voltage for a considerable time, the output of the error amplifier will respond by clamping the error amplifier output to a high voltage. Thus, requesting the maximum output current. Once the condition is removed, the regulator output rises and the error amplifier output transitions to the steady state duty cycle. In some applications, the power supply output voltage can respond faster than the error amplifier output can respond, this actuality leads to the possibility of an output overshoot. The OVTP feature minimizes the output overshoot, when using a low value output capacitor, by implementing a circuit to compare the VSENSE pin voltage to OVTP threshold which is 109% of the internal voltage reference. If the VSENSE pin voltage is greater than the OVTP threshold, the high side MOSFET is disabled preventing current from flowing to the output and minimizing output overshoot. When the VSENSE voltage drops lower than the OVTP threshold, the high side MOSFET is allowed to turn on at the next clock cycle. Thermal Shutdown The device implements an internal thermal shutdown to protect itself if the junction temperature exceeds 182C. The thermal shutdown forces the device to stop switching when the junction temperature exceeds the thermal trip threshold. Once the die temperature decreases below 182C, the device reinitiates the power up sequence by discharging the SS/TR pin. Small Signal Model for Loop Response Figure 47 shows an equivalent model for the TPS57060-Q1 control loop which can be modeled in a circuit simulation program to check frequency response and dynamic load response. The error amplifier is a transconductance amplifier with a gmEA of 97 A/V. The error amplifier can be modeled using an ideal voltage controlled current source. The resistor Ro and capacitor Co model the open loop gain and frequency response of the amplifier. The 1mV ac voltage source between the nodes a and b effectively breaks the control loop for the frequency response measurements. Plotting c/a shows the small signal response of the frequency compensation. Plotting a/b shows the small signal response of the overall loop. The dynamic loop response can be checked by replacing RL with a current source with the appropriate load step amplitude and step rate in a time domain analysis. This equivalent model is only valid for continuous conduction mode designs. 26 Submit Documentation Feedback Copyright (c) 2010, Texas Instruments Incorporated TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com DETAILED DESCRIPTION (continued) PH VO Power Stage gmps 1.9 A/V a b RESR R1 RL COMP c 0.8 V CO R3 RO VSENSE COUT gmea C2 R2 97 mA/V C1 Figure 47. Small Signal Model for Loop Response Simple Small Signal Model for Peak Current Mode Control Figure 48 describes a simple small signal model that can be used to understand how to design the frequency compensation. The TPS57060-Q1 power stage can be approximated to a voltage-controlled current source (duty cycle modulator) supplying current to the output capacitor and load resistor. The control to output transfer function is shown in Equation 14 and consists of a dc gain, one dominant pole, and one ESR zero. The quotient of the change in switch current and the change in COMP pin voltage (node c in Figure 47) is the power stage transconductance. The gmPS for the TPS57060-Q1 is 1.9A/V. The low-frequency gain of the power stage frequency response is the product of the transconductance and the load resistance as shown in Equation 15. As the load current increases and decreases, the low-frequency gain decreases and increases, respectively. This variation with the load may seem problematic at first glance, but fortunately the dominant pole moves with the load current (see Equation 16). The combined effect is highlighted by the dashed line in the right half of Figure 48. As the load current decreases, the gain increases and the pole frequency lowers, keeping the 0-dB crossover frequency the same for the varying load conditions which makes it easier to design the frequency compensation. The type of output capacitor chosen determines whether the ESR zero has a profound effect on the frequency compensation design. Using high ESR aluminum electrolytic capacitors may reduce the number frequency compensation components needed to stabilize the overall loop because the phase margin increases from the ESR zero at the lower frequencies (see Equation 17). VO Adc VC RESR fp RL gmps COUT fz Figure 48. Simple Small Signal Model and Frequency Response for Peak Current Mode Control Copyright (c) 2010, Texas Instruments Incorporated Submit Documentation Feedback 27 TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com DETAILED DESCRIPTION (continued) ae s o c1 + / 2p fZ o VOUT = Adc e VC ae s o c1 + / 2 p fP o e Adc = gmps RL (14) (15) 1 fP = COUT RL 2p (16) 1 fZ = COUT RESR 2p (17) Small Signal Model for Frequency Compensation The TPS57060-Q1 uses a transconductance amplifier for the error amplifier and readily supports three of the commonly-used frequency compensation circuits. Compensation circuits Type 2A, Type 2B, and Type 1 are shown in Figure 49. Type 2 circuits most likely implemented in high bandwidth power-supply designs using low ESR output capacitors. The Type 1 circuit is used with power-supply designs with high-ESR aluminum electrolytic or tantalum capacitors.. Equation 18 and Equation 19 show how to relate the frequency response of the amplifier to the small signal model in Figure 49. The open-loop gain and bandwidth are modeled using the RO and CO shown in Figure 49. See the application section for a design example using a Type 2A network with a low ESR output capacitor. Equation 18 through Equation 27 are provided as a reference for those who prefer to compensate using the preferred methods. Those who prefer to use prescribed method use the method outlined in the application section or use switched information. VO R1 VSENSE gmea COMP Type 2A Type 2B Type 1 Vref R2 RO CO R3 C1 C2 R3 C2 C1 Figure 49. Types of Frequency Compensation 28 Submit Documentation Feedback Copyright (c) 2010, Texas Instruments Incorporated TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com DETAILED DESCRIPTION (continued) Aol A0 P1 Z1 P2 A1 BW Figure 50. Frequency Response of the Type 2A and Type 2B Frequency Compensation Aol(V/V) gmea gmea = 2p BW (Hz) Ro = CO (18) (19) ae o s c1 + / 2p fZ1 o e EA = A0 ae o ae o s s c1 + / c1 + / 2 2 p p f f P1 o e P2 o e A0 = gmea A1 = gmea P1 = Z1 = P2 = P2 = P2 = (20) R2 Ro R1 + R2 R2 Ro| | R3 R1 + R2 (21) (22) 1 2p Ro C1 (23) 1 2p R3 C1 (24) 1 2p R3 | | RO (C2 + CO ) type 2a (25) 1 type 2b 2p R3 | | RO CO 2p R O (26) 1 type 1 (C2 + C O ) Copyright (c) 2010, Texas Instruments Incorporated (27) Submit Documentation Feedback 29 TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com APPLICATION INFORMATION Design Guide -- Step-By-Step Design Procedure This example details the design of a high frequency switching regulator design using ceramic output capacitors. A few parameters must be known in order to start the design process. These parameters are typically determined at the system level. For this example, we will start with the following known parameters: Output Voltage 3.3 V Transient Response 0 to 1.5A load step Vout = 4% Maximum Output Current 0.5 A Input Voltage 34 V nom. 12V to 48 V Output Voltage Ripple 1% of Vout Start Input Voltage (rising VIN) 8.9 V Stop Input Voltage (falling VIN) 7.9 V Selecting the Switching Frequency The first step is to decide on a switching frequency for the regulator. Typically, the user will want to choose the highest switching frequency possible since this will produce the smallest solution size. The high switching frequency allows for lower valued inductors and smaller output capacitors compared to a power supply that switches at a lower frequency. The switching frequency that can be selected is limited by the minimum on-time of the internal power switch, the input voltage and the output voltage and the frequency shift limitation. Equation 12 and Equation 13 must be used to find the maximum switching frequency for the regulator, choose the lower value of the two equations. Switching frequencies higher than these values will result in pulse skipping or the lack of overcurrent protection during a short circuit. The typical minimum on time, tonmin, is 130 ns for the TPS57060-Q1. For this example, the output voltage is 3.3 V and the maximum input voltage is 48 V, which allows for a maximum switch frequency up to 616 kHz when including the inductor resistance, on resistance and diode voltage in Equation 12. To ensure overcurrent runaway is not a concern during short circuits in your design use Equation 13 or the solid curve in Figure 42 to determine the maximum switching frequency. With a maximum input voltage of 48 V, assuming a diode voltage of 0.5 V, inductor resistance of 130m, switch resistance of 400m, a current limit value of 0.94 A and a short circuit output voltage of 0.1V. The maximum switching frequency is approximately 923 kHz. Choosing the lower of the two values and adding some margin a switching frequency of 500kHz is used. To determine the timing resistance for a given switching frequency, use Equation 11 or the curve in Figure 40. The switching frequency is set by resistor R3 shown in Figure 51. Figure 51. High Frequency, 3.3V Output Power Supply Design with Adjusted UVLO. 30 Submit Documentation Feedback Copyright (c) 2010, Texas Instruments Incorporated TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com Output Inductor Selection (LO) To calculate the minimum value of the output inductor, use Equation 28. KIND is a coefficient that represents the amount of inductor ripple current relative to the maximum output current. The inductor ripple current will be filtered by the output capacitor. Therefore, choosing high inductor ripple currents will impact the selection of the output capacitor since the output capacitor must have a ripple current rating equal to or greater than the inductor ripple current. In general, the inductor ripple value is at the discretion of the designer; however, the following guidelines may be used. For designs using low ESR output capacitors such as ceramics, a value as high as KIND = 0.3 may be used. When using higher ESR output capacitors, KIND = 0.2 yields better results. Since the inductor ripple current is part of the PWM control system, the inductor ripple current should always be greater than 30 mA for dependable operation. In a wide input voltage regulator, it is best to choose an inductor ripple current on the larger side. This allows the inductor to still have a measurable ripple current with the input voltage at its minimum. For this design example, use KIND = 0.3 and the minimum inductor value is calculated to be 39.7 H. For this design, a nearest standard value was chosen: 47H. For the output filter inductor, it is important that the RMS current and saturation current ratings not be exceeded. The RMS and peak inductor current can be found from Equation 30 and Equation 31. For this design, the RMS inductor current is 0.501 A and the peak inductor current is 0.563 A. The chosen inductor is a MSS1048-473ML. It has a saturation current rating of 1.44 A and an RMS current rating of 1.83A. As the equation set demonstrates, lower ripple currents will reduce the output voltage ripple of the regulator but will require a larger value of inductance. Selecting higher ripple currents will increase the output voltage ripple of the regulator but allow for a lower inductance value. The current flowing through the inductor is the inductor ripple current plus the output current. During power up, faults or transient load conditions, the inductor current can increase above the calculated peak inductor current level calculated above. In transient conditions, the inductor current can increase up to the switch current limit of the device. For this reason, the most conservative approach is to specify an inductor with a saturation current rating equal to or greater than the switch current limit rather than the peak inductor current. Vinmax - Vout Vout Lo min = Io KIND Vinmax sw (28) IRIPPLE = IL(rms) = VOUT (Vin max - VOUT ) Vin max L O fSW 1 - VOUT ) o / / Vinmax LO fSW o ae VOUT (IO )2 + 12 cc e (Vinmax (29) 2 (30) Iripple ILpeak = Iout + 2 (31) Output Capacitor There are three primary considerations for selecting the value of the output capacitor. The output capacitor will determine the modulator pole, the output voltage ripple, and how the regulators responds to a large change in load current. The output capacitance needs to be selected based on the more stringent of these three criteria. The desired response to a large change in the load current is the first criteria. The output capacitor needs to supply the load with current when the regulator can not. This situation would occur if there are desired hold-up times for the regulator where the output capacitor must hold the output voltage above a certain level for a specified amount of time after the input power is removed. The regulator also will temporarily not be able to supply sufficient output current if there is a large, fast increase in the current needs of the load such as transitioning from no load to a full load. The regulator usually needs two or more clock cycles for the control loop Copyright (c) 2010, Texas Instruments Incorporated Submit Documentation Feedback 31 TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com to see the change in load current and output voltage and adjust the duty cycle to react to the change. The output capacitor must be sized to supply the extra current to the load until the control loop responds to the load change. The output capacitance must be large enough to supply the difference in current for 2 clock cycles while only allowing a tolerable amount of droop in the output voltage. Equation 32 shows the minimum output capacitance necessary to accomplish this. Where Iout is the change in output current, sw is the regulators switching frequency and Vout is the allowable change in the output voltage. For this example, the transient load response is specified as a 4% change in Vout for a load step from 0A (no load) to 0.5 A (full load). For this example, Iout = 0.5-0 = 0.5 A and Vout = 0.04 x 3.3 = 0.132 V. Using these numbers gives a minimum capacitance of 15.2F. This value does not take the ESR of the output capacitor into account in the output voltage change. For ceramic capacitors, the ESR is usually small enough to ignore in this calculation. Aluminum electrolytic and tantalum capacitors have higher ESR that should be taken into account. The catch diode of the regulator can not sink current so any stored energy in the inductor will produce an output voltage overshoot when the load current rapidly decreases, see Figure 52. The output capacitor must also be sized to absorb energy stored in the inductor when transitioning from a high load current to a lower load current. The excess energy that gets stored in the output capacitor will increase the voltage on the capacitor. The capacitor must be sized to maintain the desired output voltage during these transient periods. Equation 33 is used to calculate the minimum capacitance to keep the output voltage overshoot to a desired value. Where L is the value of the inductor, IOH is the output current under heavy load, IOL is the output under light load, VF is the final peak output voltage, and Vi is the initial capacitor voltage. For this example, the worst case load step will be from 0.5 A to 0 A. The output voltage will increase during this load transition and the stated maximum in our specification is 4% of the output voltage. This will make Vf = 1.04 x 3.3 = 3.432. Vi is the initial capacitor voltage which is the nominal output voltage of 3.3 V. Using these numbers in Equation 33 yields a minimum capacitance of 13.2F. Equation 34 calculates the minimum output capacitance needed to meet the output voltage ripple specification. Where fsw is the switching frequency, Voripple is the maximum allowable output voltage ripple, and Iripple is the inductor ripple current. Equation 34 yields 1F. Equation 35 calculates the maximum ESR an output capacitor can have to meet the output voltage ripple specification. Equation 35 indicates the ESR should be less than 248m. The most stringent criteria for the output capacitor is 15.2F of capacitance to keep the output voltage in regulation during an load transient. Additional capacitance de-ratings for aging, temperature and dc bias should be factored in which will increase this minimum value. For this example, a 47 F 10V X5R ceramic capacitor with 5 m of ESR will be used. Capacitors generally have limits to the amount of ripple current they can handle without failing or producing excess heat. An output capacitor that can support the inductor ripple current must be specified. Some capacitor data sheets specify the Root Mean Square (RMS) value of the maximum ripple current. Equation 36 can be used to calculate the RMS ripple current the output capacitor needs to support. For this application, Equation 36 yields 37.7 mA. 2 DIout Cout > | sw DVout (32) ((I ) - (I ) ) ((V ) - (V ) ) 2 OH COUT > LO 2 OL 2 2 f Cout > 32 1 i (33) 1 VORIPPLE IRIPPLE (34) Submit Documentation Feedback Copyright (c) 2010, Texas Instruments Incorporated 8 | sw TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com V RESR < ORIPPLE IRIPPLE Icorms = (35) Vout (Vin max - Vout) 12 Vin max Lo | sw (36) Catch Diode The TPS57060-Q1 requires an external catch diode between the PH pin and GND. The selected diode must have a reverse voltage rating equal to or greater than Vinmax. The peak current rating of the diode must be greater than the maximum inductor current. The diode should also have a low forward voltage. Schottky diodes are typically a good choice for the catch diode due to their low forward voltage. The lower the forward voltage of the diode, the higher the efficiency of the regulator. Typically, the higher the voltage and current ratings the diode has, the higher the forward voltage will be. Since the design example has an input voltage up to 48V, a diode with a minimum of 60V reverse voltage will be selected. For the example design, the B160A Schottky diode is selected for its lower forward voltage and it comes in a larger package size which has good thermal characteristics over small devices. The typical forward voltage of the B160A is 0.50 volts. The diode must also be selected with an appropriate power rating. The diode conducts the output current during the off-time of the internal power switch. The off-time of the internal switch is a function of the maximum input voltage, the output voltage, and the switching frequency. The output current during the off-time is multiplied by the forward voltage of the diode which equals the conduction losses of the diode. At higher switch frequencies, the ac losses of the diode need to be taken into account. The ac losses of the diode are due to the charging and discharging of the junction capacitance and reverse recovery. Equation 37 is used to calculate the total power dissipation, conduction losses plus ac losses, of the diode. The B160A has a junction capacitance of 110pF. Using Equation 37, the selected diode will dissipate 0.297 Watts. This power dissipation, depending on mounting techniques, should produce a 5.9C temperature rise in the diode when the input voltage is 48V and the load current is 0.5A. If the power supply spends a significant amount of time at light load currents or in sleep mode consider using a diode which has a low leakage current and slightly higher forward voltage drop. 2 Pd = (Vin max - Vout) Iout Vd Cj sw (Vin + Vd) + 2 Vin max (37) Input Capacitor The TPS57060-Q1 requires a high quality ceramic, type X5R or X7R, input decoupling capacitor of at least 3 F of effective capacitance and in some applications a bulk capacitance. The effective capacitance includes any dc bias effects. The voltage rating of the input capacitor must be greater than the maximum input voltage. The capacitor must also have a ripple current rating greater than the maximum input current ripple of the TPS57060-Q1. The input ripple current can be calculated using Equation 38. The value of a ceramic capacitor varies significantly over temperature and the amount of dc bias applied to the capacitor. The capacitance variations due to temperature can be minimized by selecting a dielectric material that is stable over temperature. X5R and X7R ceramic dielectrics are usually selected for power regulator capacitors because they have a high capacitance to volume ratio and are fairly stable over temperature. The output capacitor must also be selected with the dc bias taken into account. The capacitance value of a capacitor decreases as the dc bias across a capacitor increases. For this example design, a ceramic capacitor with at least a 60V voltage rating is required to support the maximum input voltage. Common standard ceramic capacitor voltage ratings include 4V, 6.3V, 10V, 16V, 25V, 50V or 100V so a 100V capacitor should be selected. For this example, two 2.2F, 100V capacitors in parallel have been selected. Table 1 shows a selection of high voltage capacitors. The input capacitance value determines the input ripple voltage of the regulator. The input voltage ripple can be calculated using Equation 39. Using the design example values, Ioutmax = 0.5 A, Cin = 4.4F, sw = 500 kHz, yields an input voltage ripple of 57 mV and a rms input ripple current of 0.223A. Copyright (c) 2010, Texas Instruments Incorporated Submit Documentation Feedback 33 TPS57060-Q1 SLVSAP2 - DECEMBER 2010 Icirms = Iout www.ti.com Vout Vin min (Vin min - Vout ) Vin min (38) Iout max 0.25 Vin = Cin | sw (39) Table 1. Capacitor Types VENDOR VALUE (F) 1.0 to 2.2 1.0 to 4.7 Murata 1.0 1.0 to 2.2 1.0 10 1.8 1.0 to 1.2 Vishay 1.0 to 3.9 1.0 to 1.8 1.0 to 2.2 TDK 1.5 to 6.8 1.0. to 2.2 1.0 to 3.3 1.0 to 4.7 AVX 1.0 1.0 to 4.7 1.0 to 2.2 EIA Size 1210 1206 2220 2225 1812 1210 1210 1812 VOLTAGE DIALECTRIC 100 V COMMENTS GRM32 series 50 V 100 V GRM31 series 50 V 50 V 100 V VJ X7R series 50 V 100 V 100 V 50 V 100 V 50 V X7R C series C4532 C series C3225 50 V 100 V 50 V X7R dielectric series 100 V Slow Start Capacitor The slow start capacitor determines the minimum amount of time it will take for the output voltage to reach its nominal programmed value during power up. This is useful if a load requires a controlled voltage slew rate. This is also used if the output capacitance is large and would require large amounts of current to quickly charge the capacitor to the output voltage level. The large currents necessary to charge the capacitor may make the TPS57060-Q1 reach the current limit or excessive current draw from the input power supply may cause the input voltage rail to sag. Limiting the output voltage slew rate solves both of these problems. The slow start time must be long enough to allow the regulator to charge the output capacitor up to the output voltage without drawing excessive current. Equation 40 can be used to find the minimum slow start time, tss, necessary to charge the output capacitor, Cout, from 10% to 90% of the output voltage, Vout, with an average slow start current of Issavg. In the example, to charge the 47F output capacitor up to 3.3V while only allowing the average input current to be 0.125A would require a 1 ms slow start time. Once the slow start time is known, the slow start capacitor value can be calculated using Equation 6. For the example circuit, the slow start time is not too critical since the output capacitor value is 47F which does not require much current to charge to 3.3V. The example circuit has the slow start time set to an arbitrary value of 3.2ms which requires a 0.01 F capacitor. Cout Vout 0.8 Tss > Issavg (40) Bootstrap Capacitor Selection A 0.1-F ceramic capacitor must be connected between the BOOT and PH pins for proper operation. It is recommended to use a ceramic capacitor with X5R or better grade dielectric. The capacitor should have a 10V or higher voltage rating. 34 Submit Documentation Feedback Copyright (c) 2010, Texas Instruments Incorporated TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com Under Voltage Lock Out Set Point The Under Voltage Lock Out (UVLO) can be adjusted using an external voltage divider on the EN pin of the TPS57060-Q1. The UVLO has two thresholds, one for power up when the input voltage is rising and one for power down or brown outs when the input voltage is falling. For the example design, the supply should turn on and start switching once the input voltage increases above 8.9V (enabled). After the regulator starts switching, it should continue to do so until the input voltage falls below 7.9V (UVLO stop). The programmable UVLO and enable voltages are set using a resistor divider between Vin and ground to the EN pin. Equation 2 through Equation 3 can be used to calculate the resistance values necessary. For the example application, a 332k between Vin and EN and a 56.2k between EN and ground are required to produce the 8.9 and 7.9 volt start and stop voltages. Output Voltage and Feedback Resistors Selection For the example design, 10.0 k was selected for R2. Using Equation 1, R1 is calculated as 31.25 k. The nearest standard 1% resistor is 31.6 k. Due to current leakage of the VSENSE pin, the current flowing through the feedback network should be greater than 1 A in order to maintain the output voltage accuracy. This requirement makes the maximum value of R2 equal to 800 k. Choosing higher resistor values will decrease quiescent current and improve efficiency at low output currents but may introduce noise immunity problems. Compensation There are several methods used to compensate DC/DC regulators. The method presented here is easy to calculate and ignores the effects of the slope compensation that is internal to the device. Since the slope compensation is ignored, the actual cross over frequency will usually be lower than the cross over frequency used in the calculations. This method assume the crossover frequency is between the modulator pole and the esr zero and the esr zero is at least 10 times greater the modulator pole. Use SwitcherPro software for a more accurate design. To get started, the modulator pole, fpmod, and the esr zero, fz1 must be calculated using Equation 41 and Equation 42. For Cout, use a derated value of 40 f. Use equations Equation 43 and Equation 44, to estimate a starting point for the crossover frequency, fco, to design the compensation. For the example design, fpmod is 603 Hz and fzmod is 796 kHz. Equation 43 is the geometric mean of the modulator pole and the esr zero and Equation 44 is the mean of modulator pole and the switching frequency. Equation 43 yields 21.9 kHz and Equation 44 gives 12.3 kHz. Use the lower value of Equation 43 or Equation 44 for an initial crossover frequency. For this example, fco is 12.3kHz. Next, the compensation components are calculated. A resistor in series with a capacitor is used to create a compensating zero. A capacitor in parallel to these two components forms the compensating pole. Ioutmax |p mod = 2 x p x Vout x Cout (41) 1 | z mod = 2 p Resr x Cout (42) fco = f p mod f z mod fco = f p mod (43) f sw 2 (44) To determine the compensation resistor, R4, use Equation 45. Assume the power stage transconductance, gmps, is 1.9A/V. The output voltage, Vo, reference voltage, VREF, and amplifier transconductance, gmea, are 3.3V, 0.8V and 92A/V, respectively. R4 is calculated to be 72.6 k, use the nearest standard value of 73.2k. Use Equation 46 to set the compensation zero to the modulator pole frequency. Equation 46 yields 3600pF for compensating capacitor C7, a 3300pF is used on the board. o ae 2 p fco Cout o ae Vout R4 = c / /c gmps e o e Vref gmea o (45) 1 C7 = 2 p R4 f p m od (46) Copyright (c) 2010, Texas Instruments Incorporated Submit Documentation Feedback 35 TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com Use the larger value of Equation 47 and Equation 48 to calculate the C8, to set the compensation pole. Equation 48 yields 8.7pF so the nearest standard of 10pF is used. C Re sr C8 = o R4 (47) C8 = 1 R4 f sw p (48) Discontinuous Mode and Eco Mode Boundary With an input voltage of 34V, the power supply enters discontinuous mode when the output current is less than 60mA. The power supply enters EcoMode when the output current is lower than 38mA. The input current draw at no load is 228A. APPLICATION CURVES 36 Figure 52. Load Transient Figure 53. Startup With VIN Figure 54. Output Ripple CCM Figure 55. Output Ripple, DCM Submit Documentation Feedback Copyright (c) 2010, Texas Instruments Incorporated TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com Figure 56. Output Ripple, PSM Figure 57. Input Ripple CCM 90 80 70 Efficiency - % 60 50 VIN = 34 V VIN = 24 V VIN = 18 V VIN = 12 V VIN = 42 40 30 20 10 VOUT = 3.3 V 0 0 Figure 58. Input Ripple DCM 0.05 0.10 0.15 0.20 0.25 0.30 0.35 IO - Output Current - A 0.40 0.45 0.50 Figure 59. Efficiency vs Load Current 100 60 90 150 40 80 100 Phase 20 Vin = 18 V 50 Vin = 12 V Vin = 24 V Vin = 34 V 40 30 0 0 Gain Phase - o 50 60 Gain - dB Efficiency - % 70 -50 Vin = 42 V -20 -100 20 -40 0 0 -150 VOUT = 3.3 V 10 0.02 0.04 0.06 IO - Output Current - A 0.08 Figure 60. Light Load Efficiency Copyright (c) 2010, Texas Instruments Incorporated 0.10 -60 100 1-103 1-104 f - Frequency - Hz 1-105 1-106 Figure 61. Overall Loop Frequency Response Submit Documentation Feedback 37 TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com 0.1 0.1 0.06 0.06 0.04 0.04 0.02 0 -0.02 0 -0.02 -0.04 -0.04 -0.06 -0.08 -0.08 -0.1 0.25 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 Load Current - A Figure 62. Regulation vs Load Current 38 0.02 -0.06 -0.1 0.00 IO = 0.25 A 0.08 VI = 34 V Regulation (%) Regulation (%) 0.08 Submit Documentation Feedback 0.5 10 15 20 25 30 35 40 45 50 55 60 VI - Input Voltage - V Figure 63. Regulation vs Input Voltage Copyright (c) 2010, Texas Instruments Incorporated TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com Power Dissipation Estimate The following formulas show how to estimate the IC power dissipation under continuous conduction mode (CCM) operation. These equations should not be used if the device is working in discontinuous conduction mode (DCM). The power dissipation of the IC includes conduction loss (Pcon), switching loss (Psw), gate drive loss (Pgd) and supply current (Pq). Vout Pcon = Io2 RDS(on) Vin (49) Psw = Vin 2 | sw lo 0.25 10-9 Pgd = Vin 3 10 Pq = 116 10 -6 -9 (50) | sw (51) Vin (52) Where: IOUT is the output current (A). RDS(on) is the on-resistance of the high-side MOSFET (). VOUT is the output voltage (V). VIN is the input voltage (V). fsw is the switching frequency (Hz). So Ptot = Pcon + Psw + Pgd + Pq (53) For given TA, TJ = TA + Rth Ptot (54) For given TJMAX = 150C TAmax = TJmax - Rth Ptot (55) Where: Ptot is the total device power dissipation (W). TA is the ambient temperature (C). TJ is the junction temperature (C). Rth is the thermal resistance of the package (C/W). TJMAX is maximum junction temperature (C). TAMAX is maximum ambient temperature (C). There will be additional power losses in the regulator circuit due to the inductor ac and dc losses, the catch diode and trace resistance that will impact the overall efficiency of the regulator. Copyright (c) 2010, Texas Instruments Incorporated Submit Documentation Feedback 39 TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com Layout Layout is a critical portion of good power supply design. There are several signals paths that conduct fast changing currents or voltages that can interact with stray inductance or parasitic capacitance to generate noise or degrade the power supplies performance. To help eliminate these problems, the VIN pin should be bypassed to ground with a low ESR ceramic bypass capacitor with X5R or X7R dielectric. Care should be taken to minimize the loop area formed by the bypass capacitor connections, the VIN pin, and the anode of the catch diode. See Figure 64 for a PCB layout example. The GND pin should be tied directly to the power pad under the IC and the power pad. The power pad should be connected to any internal PCB ground planes using multiple vias directly under the IC. The PH pin should be routed to the cathode of the catch diode and to the output inductor. Since the PH connection is the switching node, the catch diode and output inductor should be located close to the PH pins, and the area of the PCB conductor minimized to prevent excessive capacitive coupling. For operation at full rated load, the top side ground area must provide adequate heat dissipating area. The RT/CLK pin is sensitive to noise so the RT resistor should be located as close as possible to the IC and routed with minimal lengths of trace. The additional external components can be placed approximately as shown. It may be possible to obtain acceptable performance with alternate PCB layouts, however this layout has been shown to produce good results and is meant as a guideline. Vout Output Capacitor Topside Ground Area Input Bypass Capacitor Vin UVLO Adjust Resistors Slow Start Capacitor Output Inductor Route Boot Capacitor Trace on another layer to provide wide path for topside ground BOOT Catch Diode PH VIN GND EN COMP SS/TR VSENSE RT/CLK PWRGD Frequency Set Resistor Compensation Network Resistor Divider Thermal VIA Signal VIA Figure 64. PCB Layout Example Estimated Circuit Area The estimated printed circuit board area for the components used in the design of Figure 51 is 0.55 in2. This area does not include test points or connectors. 40 Submit Documentation Feedback Copyright (c) 2010, Texas Instruments Incorporated TPS57060-Q1 SLVSAP2 - DECEMBER 2010 www.ti.com VIN + CIN Cboot 0.1mF Lo150 mH BOOT VIN Cd 1 mF PH R1 14 kW GND R2 1kW TPS57060-Q1 GND + Co 2x15 mF VOUT VSENSE EN SS/TR COMP RT/CLK Css 0.1 mF RT 237 kW Rcomp 52.3 kW Czero 27 nF Cpole 82 pF Figure 65. +24V to -12V Inverting Power Supply from SLVA317 Application Note Copyright (c) 2010, Texas Instruments Incorporated Submit Documentation Feedback 41 PACKAGE OPTION ADDENDUM www.ti.com 29-Aug-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) TPS57060QDGQRQ1 ACTIVE MSOPPowerPAD DGQ 10 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR TPS57060QDRCRQ1 ACTIVE SON DRC 10 1 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 29-Aug-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TPS57060QDGQRQ1 MSOPPower PAD DGQ 10 2500 330.0 12.4 5.3 3.3 1.3 8.0 12.0 Q1 TPS57060QDRCRQ1 SON DRC 10 1 330.0 12.4 3.3 3.3 1.0 8.0 12.0 Q2 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 29-Aug-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS57060QDGQRQ1 MSOP-PowerPAD DGQ 10 2500 370.0 355.0 55.0 TPS57060QDRCRQ1 SON DRC 10 1 370.0 355.0 55.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated