FM3560M20X - Fairchild Semiconductor

1www.fairchildsemi.com

FM3540/60

4/5 Bit Multiplexed, 1 Bit Latched Port with Standard 2-Wire Bus Interface and Non-Volatile Latches

www.fairchildsemi.com

FM3540/60 Rev. C

FM3540/60

4/5 Bit Multiplexed, 1 Bit Latched Port with Standard

2-Wire Bus Interface and Non-Volatile Latches

General Description

The FM3540/60 multiplexes the I-port input signals with two

internal non-volatile registers that can be loaded through the serial

port. The multiplexer is selected via the serial port and defaults to

the I-Port upon power-up. Pull-up resistors are provided on the

input port to accommodate connections to open drain outputs and

to eliminate the need for external resistors. The device supports

a choice of either 2.5V output or Open Drain Outputs for easy

interface to devices with different VDD Levels.

The serial port is an IIC compatible slave only interface and

supports both 100kbits and 400kbits modes of operation. The port

is used to read the I-Port, Write Data to the internal non-volatile

Block Diagram

October 2001

registers and select whether the I-Port or one of the internal non-

volatile registers is output to the Y-port. The FM3540/60 is

fabricated with an advanced CMOS technology to achieve high

density and low power.

Features

■Extended Operating Voltage Range 3.0V-5.5V

■IIC Compatible Slave Interface.

■ESD performance: Human body model > 2000V

■Choice of 2.5V outputs or Open-Drain Outputs

SOPRA

SOPRB

IIC

Interface

Start/Stop

Logic

Shift

Comparator

Control Logic

Mux3

Mux2

Non_Mux_Out

Y[4:0]

I[4:0]

IIC Read Logic

SDA

SCL

ASEL

OVRD

MUXSEL

MXSB, MXSA

Mux1

2www.fairchildsemi.com

FM3540/60

4/5 Bit Multiplexed, 1 Bit Latched Port with Standard 2-Wire Bus Interface and Non-Volatile Latches

www.fairchildsemi.com

FM3540/60 Rev. C

SDA 1 14 SCL

I0 2 13 VCC

I1 3 12 Y0

I2 4 11 Y1

I3 5 10 Y2

I4 6 9Y3

GND 7 8Y4

SCL 1 20 V

SDA 2 19 ASEL

OVRD 3 18 WP

I0 4 17 Non_Mux_Out

I1 5 16 MUXSEL

I2 6 15 Y0

I3 7 14 Y1

I4 8 13 Y2

Level 9 12 Y3

GND 10 11 Y4

Ordering Information

Order Package Package Y-Port Device

Number Number Description Packing Output Type Address

FM3540CM14 M14A 14-Pin SO T&R Open-Collector 1001110

FM3540CMT14 MTC14 14-Pin TSSOP T&R Open-Collector 1001110

FM3540SM14 M14A 14-Pin SO T&R Fixed 2.5V 1001110

FM3540SMT14 MTC14 14-Pin TSSOP T&R Fixed 2.5V 1001110

FM3560M20 M20B 20-Pin SO T&R (See Note below) (See Note below)

FM3560MT20 MTC20 20-Pin TSSOP T&R (See Note below) (See Note below)

Note About Y-Port Output Type:

FM3560 device has a dedicated input pin (LEVEL) to select either "Fixed 2.5Volts" or "Open-Collector" Y-Port output type.

Note About Device Address:

1. For FM3540 with an alternate device address of 0110111, contact Fairchild Marketing/Sales.

2. FM3560 device has a dedicated input pin (ASEL) to select either "1001110" or 0110111" as device address.

Pin Connection Diagrams

14-Pin Packages

FM3540

20-Pin Packages

FM3560

Pin Description

Pin Name Description

I[0:4] Data Inputs w/Pullups (10K-40K)

Y[0:4] O/D Data Outputs

SCL Serial Port Clock Input (120K pullup)

Override# Override Input, sets all outputs to 0

WP Write Protect Input

Non_Mux_Out Non-Multiplexed Output

Mux_Sel Mux. Select Input

Level Level Select Input

ASEL Address Select Input

SDA Serial Port Data I/O (120K pullup)

3www.fairchildsemi.com

FM3540/60

4/5 Bit Multiplexed, 1 Bit Latched Port with Standard 2-Wire Bus Interface and Non-Volatile Latches

www.fairchildsemi.com

FM3540/60 Rev. C

Functional Description

The FM3540/60 has two primary functional modes of operation

and an additional mode for programming the device.

Operational Modes

During standard operation the device will either pass an address

to the Y-Port from the I-Port or from an internally programmed

value. At power up the device will default to passing the I-Port

value to the Y-Port.

The I-port values are generated from the motherboard of the

system and may be hardwired or driven by another device. Pull-

up resistors are provided on the device to accommodate this

device being driven by open drain output drivers. The device

expects standard CMOS input signals. The level of the output

signal is determined by the Level input. If this input is connected

to Vss/Ground, the output is at 2.5V on the multiplexed outputs

(Y0-Y4). The non-multiplexed output is always at CMOS levels.

The Level input, if left unconnected (it has an internal pullup), will

cause the Y0-Y4 outputs to operate as open-drain outputs. The

override# input, when set to 0, will cause all the outputs to be set

to 0. The WP signal, if set to logic 1, will prevent data from being

written to the non-volatile register.

The mux_sel input, when set to logic 0, will select the data from the

non-volatile register to drive on the Y0-4 outputs. If set to logic 1,

the data from the inputs are selected instead. The non_mux_out

latch is transparent when the mux_sel signal is at logic 0, and will

latch data when the mux_select is in a logic 1 state.

Output Port: Y0-Y4

The output port is an open drain output to allow for easy connec-

tion to devices running at different voltage levels. The port is

always active and either passes the value on the I-Port or the value

in the Serial output port Register (SOPR). Changing the Mux Path

is accomplished by writing to b7, b6 of the Serial Input Port

the default path is from the I-Port through to the output port. The

multiplexer only updates when an IIC stop condition is observed.

The FM3540/60 has 3 registers in total. These registers are made

up of a combination of read only, write only and read write bits. The

two registers are listed below.

Serial Output Port Register A(SOPRA) Address: 00H

- A read/

write register that contains the new value to be written to output

Port-Y and the multiplexer select bit.

Serial Output Port Register B(SOPRB) Address: 01H

- A read/

write register that contains the new value to be written to output

Port-Y and the multiplexer select bit.

Parallel Input Port Register (PIPR) Address: 02H

- A read only

Serial Output Port Register (SOPR)

(Address 000b and 001b)

MXSB MXSA Data Field

0 0 I5 NMO I3 I2 I1 I0

b7 b6 b5 b4 b3 b2 B1 b0

b7-b6 - Multiplexer Select Bits (MXSB,MXSA)

00 - Multiplexer passes the SOPR(A).

01 - Multiplexer passer the SOPR(B).

10 - Multiplexer defaults to passing the I-Port Value.

b5, b3-b0 - Data Field. New value to be output through the

multiplexer.

nmo - Non multiplexed output from internal non-volatile bit

Parallel Input Port Register (PIPR)

(Address 002b)

Address Field Data Field

0 0 0 I4 I3I2I1 I0

b7 b6 b5 b4 b3 b2 B1 b0

b7-b5 - Address field. Value is always 000

b4-b0 - Data Field. Value is equal to the value on the I-Port.

The external Port Register captures the value on the I-Port. Data

is latched into this register on the first clock after a start condition

is seen. This insures that a valid value will always be in this register

if it is read. This register is a read only register with respect to the

IIC port.

Over- mux_ Non_

ride# sel MXSB MXSA mux_outputs mux_output

0 0 X X all 0's all 0's

0 1 X X Mux_inputs latched NMO

(see note 1)

1 0 1 0 Mux_inputs latched NMO

(see note 1)

1 0 0 0 From Non- From non-

volatile reg- volatile reg-

ister (SOPRA) ister (SOPRA)

1 0 1 1 Do not use this combination

1 0 0 1 From Non- From non-

volatile reg- volatile reg-

ister (SOPRB) ister (SOPRB)

1 1 Note 2 Note 1 Mux_inputs From Non-

volatile reg-

ister (SOPRA

or SOPRB)

Note 1: Latched NMO state will be the value present on the NMO output at the time

of the mux_sel input transitioning from logic 0 to logic 1 state.

Note 2: Output depends on previously selected state of MXSB and MXSA bits

written to device.

4www.fairchildsemi.com

FM3540/60

4/5 Bit Multiplexed, 1 Bit Latched Port with Standard 2-Wire Bus Interface and Non-Volatile Latches

www.fairchildsemi.com

FM3540/60 Rev. C

Multiplexer Logic

The output multiplexer logic determines what value is actually

output to the Y-port. The value that is output is dependent upon b7-

b6 of the SOPRA and SOPRB registers, as well as the external

mux_sel and override# inputs. The is only one set of MXS bits in

the SOPRA and SOPRB registers. Regardless of whether one

writes to SOPRA or SOPRB register for setting the MXS bits, the

result is the same. These same bits appear in both the registers.

If the mux_sel is logic 0 and OVRD is logic 1, then, if b7,b6 is “10”

then the value on the I-port is passed. When b7 is “00” the value

of the SOPRA register is passed on the next IIC stop condition,

and .When b7 is “01” the value of the SOPRB register is passed

on the next IIC stop condition. If mux_sel is logic 1 and OVRD is

logic 1, the input lines I0-4 are used to drive the outputs. The above

table describes all the combinations.

IIC Interface

The IIC Interface is a standard slave interface. As a slave interface

the device will not generate its own clock. Data can be read from

and written into the device. Commands for reading and writing the

registers are generated by the IIC Master.

START and STOP Conditions

If so desired only the SOPRA register can be read. This is

accomplished by issuing a stop command after acknowledge bit

for the first byte read. If no stop is issued, the device will output the

registers in the above sequence.

Writing to the Registers

Data is written to the SOPR registers through the serial port

interface. When a write request is received with the Start Address

it is assumed that the intent is to write the SOPR registers. The

value placed in the least 6 significant bits of the register contain the

new code to be placed in the SOPR A/B registers. The value of the

two most significant bits must contain the address of the destina-

tion register SOPRA or SOPRB.

The internal non-volatile latch takes about 10 ms to update its

data. The new data is reflected on the outputs after the internal

non-volatile latch is updated, if the corresponding select bits

(MXSx, OVRD and mux_sel) are set to reflect the state of the non-

volatile register

Slave SOPRA SOPRB PIPR

S Address R A Register A Register A Register A P

S 1001110 1 A 00bbbbbb A 00bbbbbb A 00bbbbbb A P

Slave SOPRx

S Address W A Register A S

S 1001110 0 A xxbbbbbb A S

xx = Register Selection bits (MXSB and MXSA) xx = 00 selects

SOPRA, 01 selects SOPRB

Repeated Start Condition

Slave SOPRA Slave SOPRx

S Address R A Register A S Address W A Register A P

S 1001110 1 A 00bbbbbb A S 1001110 0 A xxbbbbbb A P

Figure 4

The IIC protocol uniquely defines START and STOP conditions.

A START condition is defined as a HIGH to LOW transition of the

SDA signal while SCL is HIGH. A STOP condition is defined as a

LOW to HIGH transition of the SDA signal while SCL is HIGH.

These are shown in Figure 2.

Device Addressing

The device uses 7 bit IIC addressing. The address has been

defined as 1001 110 if the ASEL input is ‘1’ and 0110 111 if the

ASEL input is ‘0’. The address byte is the first byte of data sent after

a start condition. This is the only address that this device will

respond to. The device will not respond to the general call address

0000 000.

Reading from the Registers

Data can be read from both of the internal registers. All reads are

non-destructive and do not change the value in the register or the

internal state of the device. When a start condition is received with

a read request both registers can be read out in the following

sequence.

(1) SOPRA - Serial Output Port Register A

(2) SPORB - Serial Output Port Register B

(3) PIPR - PORT-I Value

SDA

SCL

START

Condition

STOP

Condition

5www.fairchildsemi.com

FM3540/60

4/5 Bit Multiplexed, 1 Bit Latched Port with Standard 2-Wire Bus Interface and Non-Volatile Latches

www.fairchildsemi.com

FM3540/60 Rev. C

Absolute Maximum Ratings (Note 1)

Supply Voltage (VCC ) -0.5V to +6.5V

DC Input Voltage (VI) -0.5V to +6.5V

Output Voltage (VO)

Outputs 3-STATED -0.5V to +6.5V

Outputs Active (Note 2) -0.5 to VCC+0.5V

DC Input Diode Current (IIK) VI < 0V -50mA

DC Output Diode Current (IOK)

VO < 0V -50mA

VO > Vcc +50mA

DC Output Source/Sink Current (IOH/IOL)±50mA

DC Vcc or Ground Current per

Supply Pin (ICC or Ground) ±100mA

Storage Temperature Range (TSTG) -65°C to +150°C

Recommended Operating Conditions

(Note 3)

Power Supply 3.0V to 5.5V

Input Voltage -0.3V to 5.5V

Output Voltage (VO) 0V TO VCC

Output Current IOL 3mA

Free Air Operating Temperature(TA) -0°C to +70°C

Minimum Input Edge Rate (dT/dV)

VIN = 0.8V to 2.0V, Vcc = 3.0V 10nS/V

Note 1: The “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated at these limits. The

parametric values defined in the “Electrical Characteristics” table are not guaranteed at the Absolute Maximum Ratings. The “Recommended Operating Conditions” table will

define the conditions for actual device operation.

Note 2: IO Absolute Maximum Rating must be observed.

Note 3: Floating or unused pins (inputs or I/O’s) must be held HIGH or LOW.

DC Electrical Characteristics (4.5V < VCC ≤ 5.5V)

Symbol Parameter Conditions VCC (V) Min Max Units

VIH High Level Input Voltage 4.5 - 5.5 VCC x 0.7 V

VIL Low Level Input Voltage 4.5 - 5.5 VCC x 0.3 V

VOL Low Level Output Voltage IOL = 100µA 4.5 - 5.5 0.2 V

IOL = 3mA 0.4

IIR Input Leakage Current VI=VIL 5.5 -10 +10 µA

ICC Quiescent Supply Current VI = VCC or GND 4.5 - 5.5 300 975 µA

VCC ≤ (VaI, VO) ≤ 3.6V

DC Electrical Characteristics Extended (3.0V ≤ VCC ≤ 5.5V)

Symbol Parameter Conditions Vcc (V) Min Max Units

VIH High Level Input Voltage 3.0 - 5.5 VCC x 0.7 V

VIL Low Level Input Voltage 3.0 - 5.5 VCC x 0.3 V

VOL Low Level Output Voltage IOL = 100µA 3.0 - 5.5 0.2 V

IOL = 3mA 0.4

VOH Output High Voltage Fixed output mode, ('s' grade 3.0 - 5.5 2.3 2.5 V

samples, or FM3560 with

LEVEL input = logical ‘0’) 1

TTL load, 50pf capacitance

IIR Input Leakage Current VI=VIL 5.5 -10 +10 µA

ICC Quiescent Supply Current VI = VCC or GND 3.0 - 5.5 300 975 µA

VCC ≤ (VI, VO) ≤ 3.6V

6www.fairchildsemi.com

FM3540/60

4/5 Bit Multiplexed, 1 Bit Latched Port with Standard 2-Wire Bus Interface and Non-Volatile Latches

www.fairchildsemi.com

FM3540/60 Rev. C

AC Characteristics

Symbol Parameter

= 0

C to +70

C,C

= 30pF, R

= 500

Ω

Units

VCC = 5.0V ± 0.5V VCC = 3.3 ± 0.3V

Min Max Min Max

tPHL Prop Delay I to Y 50 50 ns

TPLH Prop Delay I to Y 50 50 ns

tPHL Prop Delay to Y (from OVRD’ or Mux_Sel) 50 50 ns

TPLH Prop Delay to Y (from OVRD’ or Mux_Sel) 50 50 ns

IIC AC Characteristics

Symbol Parameter

= 0

C to +70

C,C

= 30pF, R

= 500

Ω

Units

100kHz 400kHz

Min Max Min Max

fSCL SCL Clock Frequency 100 400 kHz

T1Noise Supression Time Constant 100 50 nS

tAA SCL Low to SDA Data Out Valid 0.3 3.5 0.1 0.9 µS

tBUF Time the Bus must be free before a new 4.7 1.3 µS

Transmission can start

tHD:STA Start Condition Hold Time 4.0 0.6 µS

tLOW Clock Low Period 4.7 0.6 µS

tHIGH Clock High Period 4.0 0.6 µS

tSU:STA Start Condition Setup Time (For a 4.7 0.6

repeated Start Condition)

tHD:DAT Data in Hold Time 0 0 µS

tSU:DAT Data in Setup Time 250 100 nS

tRSDA and SCL Rise Time 1000 300 nS

tFSDA and SCL Fall Time 300 300 nS

tSU:STO Stop Condition Setup Time 4.7 0.6 µS

Capacitance

Symbol Parameter Conditions TA = +25°C Typical Units

Cin Input Capacitance (I4-I0) VI =0V or VCC, VCC=3.3 or 5.0 6 PF

CI/O Input/Output Capacitance (SDA) VI=0V or VCC, VCC=3.3 or 5.0 7 PF

COUT Output Capacitance (Y4-Y0) 7 PF

Non-Volatile Memory Characteristics

Parameter Specification

Data Retention 10 years minimum

Number of writes 1,000,000 cycles

7www.fairchildsemi.com

FM3540/60

4/5 Bit Multiplexed, 1 Bit Latched Port with Standard 2-Wire Bus Interface and Non-Volatile Latches

www.fairchildsemi.com

FM3540/60 Rev. C

Molded Small Outline Package (M)

Order Number FM3560XM

Package Number M20B

X = C for open collector

and X = S for 2.5V

Physical Dimensions inches (millimeters) unless otherwise noted

Lead No. 1

IDENT

101

0.394 - 0.419

[10.008 - 10.643]

0.496 - 05.12

[12.598 - 13.005]

0.050

[1.270]

TYP 0.008

[

0.203

]

0.014-0.020

[0.356-0.508]

30¡ TYP

0.004-0.012

[0.102-0.305]

TYP

Seating Plan

0.010

[0.254]MAX

TYP

0.093 - 0.104

[2.362 - 2.642]

0.014

[0.356]

0.291-0.299

[7.391- 7.595]

0.009-0.013

[0.229-0.330]

TYP All Leads

0.010 - 0.029

[0.254 - 0.737] 8¡ Max Typ

All Leads

x45¡

0.004

[0.102]

All Leads

Tips

0.016 - 0.050

[0.406 - 1.270]

Typ All Leads

8www.fairchildsemi.com

FM3540/60

4/5 Bit Multiplexed, 1 Bit Latched Port with Standard 2-Wire Bus Interface and Non-Volatile Latches

www.fairchildsemi.com

FM3540/60 Rev. C

Molded Small Outline Package (M)

Order Number FM3540XM

Package Number M14A

X = C for open collector

and X = S for 2.5V

Physical Dimensions inches (millimeters) unless otherwise noted

1234567

14 13 12 11 10 9 8

335

344

(8.509 - 8.788)

0.228 - 0.244

(5.791 - 6.198) 0.010

(0.254)Max.

Lead #1

IDENT

Seating

Plane

0.004 - 0.010

(0.102 - 0.254)

0.014 - 0.020

(0.356 - 0.508) Ty

0.053 - 0.069

(1.346 - 1.753)

0.050

(1.270)

Typ

0.008

(0 203)

0.014

(0.356)

0.016 - 0.050

(0.406 - 1.270)

Typ. All Leads

8° Max, Typ.

All leads

0.150 - 0.157

(3.810 - 3.988)

0.008 - 0.010

(0.203 - 0.254)

Typ. all leads

0.04

(0.102)

All lead tips

0.010 - 0.020

(

0.254 - 0.508)

x 45°

30° Typ.

9www.fairchildsemi.com

FM3540/60

4/5 Bit Multiplexed, 1 Bit Latched Port with Standard 2-Wire Bus Interface and Non-Volatile Latches

www.fairchildsemi.com

FM3540/60 Rev. C

Order Number FM3540XMT

Package Number MTC14

X = C for open collector

and X = S for 2.5V

Physical Dimensions inches (millimeters) unless otherwise noted

5.0 –0.1

3.2

6.4

14 8

4.4 – 0.1

(7.72) Typ

(4.16) Typ

(1.78) Typ

(0.42) Typ

0.2 C B A

(0.65) Typ

0.10 – 0.05 TYP

All Lead Tips

0.65 Typ.

1 Max

TYP

0.19 - 0.30 TYP

Pin #1 IDENT

0.9 - 0.20 TYP

(0.9)

0¡-8¡

0.6 –0.1

0.25

Seating

plane

Gage

plane

See detail A

Dimensions are in millimeters

Notes: Unless otherwise specified

1. Reference JEDED registration MO153. Variation AB.

Ref. Note 6, dated 7/93

Land pattern recommendation

DETAIL A

Typ. Scale: 40X

- A -

- B -

- C -

0.13 C

0.1 C

All Lead Tips

10 www.fairchildsemi.com

FM3540/60

4/5 Bit Multiplexed, 1 Bit Latched Port with Standard 2-Wire Bus Interface and Non-Volatile Latches

www.fairchildsemi.com

FM3540/60 Rev. C

Physical Dimensions inches (millimeters) unless otherwise noted

Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications.

Life Support Policy

Fairchild's products are not authorized for use as critical components in life support devices or systems without the express written

approval of the President of Fairchild Semiconductor Corporation. As used herein:

1. Life support devices or systems are devices or systems which,

(a) are intended for surgical implant into the body, or (b) support

or sustain life, and whose failure to perform, when properly

used in accordance with instructions for use provided in the

labeling, can be reasonably expected to result in a significant

injury to the user.

2. A critical component is any component of a life support device

or system whose failure to perform can be reasonably ex-

pected to cause the failure of the life support device or system,

or to affect its safety or effectiveness.

Fairchild Semiconductor Fairchild Semiconductor Fairchild Semiconductor Fairchild Semiconductor

Americas Europe Hong Kong Japan Ltd.

Customer Response Center Fax: +44 (0) 1793-856858 8/F, Room 808, Empire Centre 4F, Natsume Bldg.

Tel. 1-888-522-5372 Deutsch Tel: +49 (0) 8141-6102-0 68 Mody Road, Tsimshatsui East 2-18-6, Yushima, Bunkyo-ku

English Tel: +44 (0) 1793-856856 Kowloon. Hong Kong Tokyo, 113-0034 Japan

Français Tel: +33 (0) 1-6930-3696 Tel; +852-2722-8338 Tel: 81-3-3818-8840

Italiano Tel: +39 (0) 2-249111-1 Fax: +852-2722-8383 Fax: 81-3-3818-8841

Order Number FM3560MT

Package Number MTC20