PRODUCT DATASHEET 10Gb/s 1310nm SFP+ 10km Transceiver PART NUMBER: SFPPT-LR1-01 PRODUCT FEATURES Up to 11.1Gbps Data Links Up to 10km transmission on SMF DFB Laser and PIN receiver Metal enclosure, for lower EMI 2-wire interface with integrated Digital Diagnostic monitoring Hot-pluggable SFP+ footprint Specifications compliant with SFF 8472 Compliant with SFP+ MSA with LC connector Single 3.3V power supply Case operating temperature range: 0C to 70C Power dissipation < 1.5 W APPLICATIONS 10GBASE-LR/LW & 10G Ethernet PART NUMBER SFPPT-LR1-01 DFTO DATE REVISION ELLA 15 Sep., 2014 P1 http://www.pulseelectronics.com/ SHEET NO 1 OF 9 PRODUCT DATASHEET 10Gb/s 1310nm SFP+ 10km Transceiver STANDARD Compliant to SFF-8431 Compliant to SFF 8472 RoHS Compliant. Absolute Maximum Ratings Parameter Symbol Min. Typ. Max. Unit Storage Temperature Ts -40 - 85 C Storage Ambient Humidity HA 5 - 95 % Operating Relative Humidity RH - - 85 % Power Supply Voltage VCC -0.3 - 4 V Vcc-0.3 - Vcc+0.3 V Signal Input Voltage Note Recommended Operating Conditions Parameter Symbol Min. Typ. Max. Unit Note Case Operating Temperature Tcase 0 - 70 C Without air flow Power Supply Voltage VCC 3.14 3.3 3.47 V Power Supply Current ICC - 270 350 mA Data Rate BR 10.3125 Transmission Distance TD - Coupled fiber PART NUMBER SFPPT-LR1-01 Gbps 10 km Single mode fiber DFTO DATE REVISION ELLA 15 Sep., 2014 P1 http://www.pulseelectronics.com/ 9/125um SMF SHEET NO 2 OF 9 PRODUCT DATASHEET 10Gb/s 1310nm SFP+ 10km Transceiver Optical Characteristics Parameter Symbol Min Typ Max Unit NOTE Output Opt. Pwr POUT -6 -1 dBm 1 Optical Wavelength 1260 1355 nm Spectral Width (-20dB) 1 nm Optical Extinction Ratio ER Transmitter and Dispersion Peanlty TDP 3.2 dB RIN RIN -128 dB/Hz Transmitter Output Eye Mask 1310 3.5 dB Compliant with IEEE 802.3ae Receiver Rx Sensitivity RSENS Input Saturation Power (Overload) Psat 0.5 Wavelength Range 1270 LOS De -Assert LOSD LOS Assert LOSA C LOS Hysteresis -14.4 2 dBm 1610 nm -17 dBm -30 0.5 dBm dBm 1.0 dB Notes: 1. Class 1 Laser Safety per FDA/CDRH and IEC-825-1 regulations. 31 -12 2. Measured with a PRBS 2 -1 test pattern, @10.325Gb/s, BER<10 PART NUMBER SFPPT-LR1-01 . DFTO DATE REVISION ELLA 15 Sep., 2014 P1 http://www.pulseelectronics.com/ SHEET NO 3 OF 9 PRODUCT DATASHEET 10Gb/s 1310nm SFP+ 10km Transceiver IV. Electrical Characteristics Parameter Symbol Min Typ Max Unit Supply Voltage Vcc 3.14 3.3 3.46 V Supply Current Icc 350 mA NOTE Transmitter Input differential impedance Rin 100 Single ended data input swing Vin,pp 180 700 mV Transmit Disable Voltage VD Vcc-1.3 Vcc V Transmit Enable Voltage VEN Vee Vee+ 0.8 V 10 us 850 mV 3 Transmit Disable Assert Time 1 2 Receiver Differential data output swing Vout,pp 300 Data output rise time tr 28 ps 4 Data output fall time tf 28 ps 4 LOS Fault VLOS fault Vcc-1.3 VccHOST V 5 LOS Normal VLOS norm Vee Vee+0.8 V 5 Power Supply Rejection PSR 100 mVpp 6 Notes: 1. Connected directly to TX data input pins. AC coupled thereafter. 2. Or open circuit. 3. Into 100 ohms differential termination. 4. 20 - 80 %. 5. Loss Of Signal is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected. 6. Receiver sensitivity is compliant with power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to specified value applied through the recommended power supply filtering network. PART NUMBER SFPPT-LR1-01 DFTO DATE REVISION ELLA 15 Sep., 2014 P1 http://www.pulseelectronics.com/ SHEET NO 4 OF 9 PRODUCT DATASHEET 10Gb/s 1310nm SFP+ 10km Transceiver V. Pin Assignment Pin out of Connector Block on Host Board Pin Symbol Name/Description NOTE EET Transmitter Ground (Common with Receiver Ground) 1 FAULT Transmitter Fault. 2 Transmitter Disable. Laser output disabled on high or open. 3 V 1 T 2 3 T 4 SDA 2-wire Serial Interface Data Line 4 5 SCL 2-wire Serial Interface Clock Line 4 6 MOD_ABS Module Absent. Grounded within the module 4 7 RS0 Rate Select 0 5 8 LOS Loss of Signal indication. Logic 0 indicates normal operation. 6 9 RS1 No connection required 1 10 V EER Receiver Ground (Common with Transmitter Ground) 1 11 V EER Receiver Ground (Common with Transmitter Ground) 1 12 RD- PART NUMBER SFPPT-LR1-01 DIS Receiver Inverted DATA out. AC Coupled DFTO DATE REVISION ELLA 15 Sep., 2014 P1 http://www.pulseelectronics.com/ SHEET NO 5 OF 9 PRODUCT DATASHEET 10Gb/s 1310nm SFP+ 10km Transceiver 13 RD+ Receiver Non-inverted DATA out. AC Coupled 14 V 15 V 16 V 17 V 18 TD+ Transmitter Non-Inverted DATA in. AC Coupled. 19 TD- Transmitter Inverted DATA in. AC Coupled. 20 V EER Receiver Ground (Common with Transmitter Ground) CCR Receiver Power Supply 1 Transmitter Power Supply CCT Transmitter Ground (Common with Receiver Ground) EET 1 Transmitter Ground (Common with Receiver Ground) EET 1 Notes: 1. Circuit ground is internally isolated from chassis ground. 2. T FAULT is an open collector/drain output, which should be pulled up with a 4.7k - 10k Ohms resistor on the host board if intended for use. Pull up voltage should be between 2.0V to Vcc + 0.3V.A high output indicates a transmitter fault caused by either the TX bias current or the TX output power exceeding the preset alarm threshold. A low output indicates normal operation. In the low state, the output is pulled to <0.8V. 3. Laser output disabled on T DIS >2.0V or open, enabled on T DIS <0.8V. 4. Should be pulled up with 4.7k- 10k host board to a voltage between 2.0V and 3.6V. MOD_ABS pulls line low to indicate module is plugged in. 5. Internally pulled down per SFF-8431 Rev 4.1. 6. LOS is open collector output. It should be pulled up with 4.7k - 10k on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal. VI. Digital Diagnostic Functions SFPPT-LR1-01 transceivers support the 2-wire serial communication protocol as defined in the SFP+ MSA. The standard SFP serial ID provides access to identification information that describes the transceiver's capabilities, standard interfaces, manufacturer, and other information. Additionally, SFP+ transceivers provide a unique enhanced digital diagnostic monitoring interface, which allows PART NUMBER SFPPT-LR1-01 DFTO DATE REVISION ELLA 15 Sep., 2014 P1 http://www.pulseelectronics.com/ SHEET NO 6 OF 9 PRODUCT DATASHEET 10Gb/s 1310nm SFP+ 10km Transceiver real-time access to device operating parameters such as transceiver temperature, laser bias current, transmitted optical power, received optical power and transceiver supply voltage. It also defines a sophisticated system of alarm and warning flags, which alerts end-users when particular operating parameters are outside of a factory set normal range. The SFP MSA defines a 256-byte memory map in EEPROM that is accessible over a 2-wire serial interface at the 8 bit address 1010000X (A0h).The digital diagnostic monitoring interface makes use of the 8 bit address 1010001X (A2h), so the originally defined serial ID memory map remains unchanged. The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed through a 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL, Mod Def 1) is generated by the host. The positive edge clocks data into the SFP transceiver into those segments of the E2PROM that are not write-protected. The negative edge clocks data from the SFP transceiver. The serial data signal (SDA, Mod Def 2) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially. PART NUMBER SFPPT-LR1-01 DFTO DATE REVISION ELLA 15 Sep., 2014 P1 http://www.pulseelectronics.com/ SHEET NO 7 OF 9 PRODUCT DATASHEET 10Gb/s 1310nm SFP+ 10km Transceiver VII. Host - Transceiver Interface Block Diagram SFP+ Module PART NUMBER SFPPT-LR1-01 DFTO DATE REVISION ELLA 15 Sep., 2014 P1 http://www.pulseelectronics.com/ SHEET NO 8 OF 9 PRODUCT DATASHEET 10Gb/s 1310nm SFP+ 10km Transceiver VIII. Outline Dimensions Comply to SFF-8432 rev. 5.0, the improved Pluggable form factor specification. IX. Regulatory Compliance Feature Reference Performance Electrostatic dischargeESD IEC/EN 61000-4-2 Compatible with standards Electromagnetic Interference (EMI) FCC Part 15 Class B EN 55022 Class B (CISPR 22A) Compatible with standards Laser Eye Safety FDA 21CFR 1040.10, 1040.11 IEC/EN 60825-1, 2 Class 1 laser product Component Recognition IEC/EN 60950, UL Compatible with standards ROHS 2002/95/EC Compatible with standards EMC EN61000-3 Compatible with standards PART NUMBER SFPPT-LR1-01 DFTO DATE REVISION ELLA 15 Sep., 2014 P1 http://www.pulseelectronics.com/ SHEET NO 9 OF 9