UG334: Si5394 Evaluation Board User's Guide The Si5394 EVB is used for evaluating the Si5394 Any-Frequency, Any-Output, JitterAttenuating Clock Multiplier. There are two different EVBs for the Si5394. There is a Grade A and a Grade P board. This user guide is intended for both versions of the Si5394 EVBs. The device grade and revision is distinguished by a white 1 inch x 0.187 inch label installed in the lower left hand corner of the board. In the example below, the label "SI5394A-A-EB" indicates the evaluation board has been assembled with an Si5394 device, Grade A, Revision A, installed. (For ordering purposes only, the terms "EB" and "EVB" refer to the board and the kit respectively. For the purpose of this document, the terms are synonymous in context.) KEY FEATURES * Powered from USB port or external power supply * Onboard 48 MHz XTAL or Reference SMA Inputs allow holdover mode of operation on the Si5394 * ClockBuilder Pro(R) (CBPro) GUI programmable VDD supply allows device to operate from 3.3, 2.5, or 1.8 V * CBPro GUI programmable VDDO supplies allow each of the 10 outputs to have its own power supply voltage selectable from 3.3, 2.5, or 1.8 V * CBPro GUI-controlled voltage, current, and power measurements of VDD and all VDDO supplies * Status LEDs for power supplies and control/status signals of Si5394 * SMA connectors for input clocks, output clocks, and optional external timing reference clock silabs.com | Building a more connected world. Rev. 1.0 UG334: Si5394 Evaluation Board User's Guide Functional Block Diagram 1. Functional Block Diagram Below is a functional block diagram of the Si5394 EVB. This evaluation board can be connected to a PC via the main USB connector for programming, control, and monitoring. See 3. Quick Start or 10.2 Overview of ClockBuilder Pro Applications for more information. Figure 1.1. Si5394 EVB Functional Block Diagram silabs.com | Building a more connected world. Rev. 1.0 | 2 UG334: Si5394 Evaluation Board User's Guide Si5394 EVB Support Documentation and ClockBuilder Pro Software 2. Si5394 EVB Support Documentation and ClockBuilder Pro Software All Si5394 EVB schematics, BOMs, User's Guides, and software can be found online at: https://www.silabs.com/products/developmenttools/timing/clock/si5394a-a-evb-evaluation-kit. silabs.com | Building a more connected world. Rev. 1.0 | 3 UG334: Si5394 Evaluation Board User's Guide Quick Start 3. Quick Start 1. Install the ClockBuilder Pro desktop software from http://www.silabs.com/CBPro. 2. Connect a USB cable from Si5394 EVB to the PC where the software was installed. 3. Confirm jumpers are installed as shown in Table 4.1 Si5394 EVB Jumper Defaults1 on page 5. 4. Launch the ClockBuilder Pro Software. 5. You can use ClockBuilder Pro to create, download, and run a frequency plan on the Si5394 EVB. 6. For the Si5394 data sheet, go to http://www.silabs.com/timing. silabs.com | Building a more connected world. Rev. 1.0 | 4 UG334: Si5394 Evaluation Board User's Guide Jumper Defaults 4. Jumper Defaults Table 4.1. Si5394 EVB Jumper Defaults1 Location Type I= Installed 0 = Open Location Type I = Installed 0 = Open JP1 2-pin I JP23 2-pin O JP2 2-pin I JP24 2-pin O JP3 2-pin I JP25 2-pin all open JP4 2-pin I JP26 2-pin all open JP5 2-pin 1 to 2 JP27 2-pin O JP6 2-pin O JP28 2-pin O JP7 2-pin O JP29 2-pin all open JP8 2-pin O JP30 2-pin all open JP9 2-pin O JP31 2-pin O JP10 2-pin O JP32 2-pin O JP11 2-pin O JP33 2-pin all open JP12 2-pin O JP17 5x2 Hdr All 5 installed JP13 2-pin O Note: 1. Refer to the Si5394 EVB schematics for the functionality associated with each jumper. silabs.com | Building a more connected world. Rev. 1.0 | 5 UG334: Si5394 Evaluation Board User's Guide Status LEDs 5. Status LEDs Location Silkscreen Color Status Function Indication D5 INTRB Blue Dut Interrupt D7 LOLB Blue DUT Loss of Lock D8 LOSXAXBB Blue DUT Loss of Reference D11 +5V MAIN Green Main USB +5V present D12 READY Green MCU Ready D13 BUSY Green MCU Busy D11 is illuminated when USB +5V supply voltage is present. D12 and D13 are status LEDs showing onboard MCU activity. Figure 5.1. Status LEDs silabs.com | Building a more connected world. Rev. 1.0 | 6 UG334: Si5394 Evaluation Board User's Guide External Reference Input (XA/XB) 6. External Reference Input (XA/XB) An external reference (XTAL) is used in combination with the internal oscillator to produce an ultra-low jitter reference clock for the DSPLL and for providing a stable reference for the free-run and holdover modes. The Si5394 EVB can also accommodate an external reference clock instead of a crystal. To evaluate the device with a REFCLK, C93 and C94 must be populated and the XTAL removed (see Figure 3). The REFCLK can then be applied to J25 and J26. Figure 6.1. External Reference Input Circuit silabs.com | Building a more connected world. Rev. 1.0 | 7 UG334: Si5394 Evaluation Board User's Guide Clock Input Circuits (INx/INxB) 7. Clock Input Circuits (INx/INxB) The Si5394 EVB has eight SMA connectors (IN0, IN0B - IN3, IN3B) for receiving external clock signals. All input clocks are terminated as shown below. Note input clocks are ac-coupled and 50 terminated. This represents four differential input clock pairs. Single-ended clocks can be used by appropriately driving one side of the differential pair with a single-ended clock. For details on how to configure inputs as single-ended, refer to the Si5394 data sheet. Figure 7.1. Input Clock Termination Circuit silabs.com | Building a more connected world. Rev. 1.0 | 8 UG334: Si5394 Evaluation Board User's Guide Clock Output Circuits (OUTx/OUTxB) 8. Clock Output Circuits (OUTx/OUTxB) Each of the eight output drivers (4 differential pairs) is ac-coupled to its respective SMA connector. The output clock termination circuit is shown below. The output signal will have no dc bias. If dc coupling is required, the ac coupling capacitors can be replaced with a resistor of appropriate value. The Si5394 EVB provides pads for optional output termination resistors and/or low-frequency capacitors. Note that components with schematic "NI" designation are not normally populated on the Si5394 EVB and provide locations on the PCB for optional dc/ac terminations by the end user. Figure 8.1. Output Clock Termination Circuit silabs.com | Building a more connected world. Rev. 1.0 | 9 UG334: Si5394 Evaluation Board User's Guide Installing ClockBuilder Pro Desktop Software 9. Installing ClockBuilder Pro Desktop Software To install the CBOPro software on any Windows 7 (or above) PC, go to http://www.silabs.com/CBPro and download the ClockBuilder Pro software. Installation instructions and User's Guide for ClockBuilder Pro can be found at the download link shown above. silabs.com | Building a more connected world. Rev. 1.0 | 10 UG334: Si5394 Evaluation Board User's Guide Using the Si5394 EVB 10. Using the Si5394 EVB 10.1 Connecting the EVB to Your Host PC Once ClockBuilder Pro software is installed, connect to the EVB with a USB cable as shown in the figure below: Figure 10.1. EVB Connection Diagram 10.2 Overview of ClockBuilder Pro Applications Note: The following instructions and screen captures may vary slightly depending on the grade of your device and your version of ClockBuilder Pro. (The screen captures below were taken for a board labeled "SI5394A-A-EB".) The ClockBuilder Pro installer will install two main applications: silabs.com | Building a more connected world. Rev. 1.0 | 11 UG334: Si5394 Evaluation Board User's Guide Using the Si5394 EVB Figure 10.2. Application #1: ClockBuilder Pro Wizard Use the CBPro wizard to: * Create a new design * Review or edit an existing design * Export: create in-system programming Figure 10.3. Application #2: EVBGUI Use the EVB GUI to: * Download configuration to EVB's DUT (Si5394) * Control the EVB's regulators * Monitor voltage, current, power on theEVB silabs.com | Building a more connected world. Rev. 1.0 | 12 UG334: Si5394 Evaluation Board User's Guide Using the Si5394 EVB 10.3 Common ClockBuilder Pro Workflow Scenarios There are three common workflow scenarios when using CBPro and the Si5394 EVB. These workflow scenarios are: * Workflow Scenario #1: Testing a Silicon Labs-Created Default Configuration * Workflow Scenario #2: Modifying the Default Silicon Labs-Created Device Configuration * Workflow Scenario #3: Testing a User-Created Device Configuration Each is described in more detail in the following sections. 10.4 Workflow Scenario 1: Testing a Silicon Labs Default Configuration The flow for using the EVB GUI to initialize and control a device on the EVB is as follows. Once the PC and EVB are connected, launch ClockBuilder Pro by clicking on this icon on your PC's desktop: Figure 10.4. ClockBuilder Pro Desktop Icon If an EVB is detected, click on the "Open Default Plan" button on the Wizard's main menu. CBPro automatically detects the EVB and device type. Figure 10.5. Open Default Plan silabs.com | Building a more connected world. Rev. 1.0 | 13 UG334: Si5394 Evaluation Board User's Guide Using the Si5394 EVB Once you open the default plan (based on your EVB model number), a popup will appear Figure 10.6. Write Design to EVB Dialog Select "Yes" to write the default plan to the Si5394 device mounted on your EVB. This ensures the device is completely reconfigured per the Silicon Labs default plan for the DUT type mounted on the EVB. Figure 10.7. Writing Design Status After CBPro writes the default plan to the EVB, click on "Open EVB GUI" as shown below: Figure 10.8. Open EVB GUI The EVB GUI will appear. Note all power supplies will be set to the values defined in the device's default CBPro project file created by Silicon Labs, as shown below: silabs.com | Building a more connected world. Rev. 1.0 | 14 UG334: Si5394 Evaluation Board User's Guide Using the Si5394 EVB Figure 10.9. EVB GUI Window silabs.com | Building a more connected world. Rev. 1.0 | 15 UG334: Si5394 Evaluation Board User's Guide Using the Si5394 EVB 10.4.1 Verify Free-Run Mode Operation Assuming no external clocks have been connected to the INPUT CLOCK differential SMA connectors (labeled "INx/INxB") located around the perimeter of the EVB, the DUT should now be operating in free-run mode, as the DUT will be locked to the crystal in this case. You can run aquick check to determine if the device is powered up and generating output clocks (and consuming power) by clicking on the Read All button highlighted above and then reviewing the voltage, current and power readings for each VDDx supply. Note: Shutting the VDD and VDDA supplies "Off" then "On" will power-down and reset the DUT. Every time you do this, to reload the Silicon Labs-created default plan into the DUT's register space, you must go back to the Wizard's main menu and select "Write Design to EVB" as shown below. Figure 10.10. Write Design to EVB Failure to perform the step above will cause the device to read in a pre-programmed plan from its non-volatile memory (NVM). However, the plan loaded from the NVM may not be the latest plan recommended by Silicon Labs for evaluation. At this point, you should verify the presence and frequencies of the output clocks (running to free-run mode from the crystal) using appropriate external instrumentation connected to the output clock SMA connectors. To verify the output clocks are toggling at the correct frequency and signal format, click on View Design Report as highlighted below. silabs.com | Building a more connected world. Rev. 1.0 | 16 UG334: Si5394 Evaluation Board User's Guide Using the Si5394 EVB Figure 10.11. View Design Report Your configuration's design report will appear in a new window, as shown below. Compare the observed output clocks to the frequencies and formats noted in your default project's Design Report. silabs.com | Building a more connected world. Rev. 1.0 | 17 UG334: Si5394 Evaluation Board User's Guide Using the Si5394 EVB Figure 10.12. Design Report Window 10.4.2 Verify Locked Mode Operation Assuming you connect the correct input clocks to the EVB (as noted in the Design Report shown above), the DUT on your EVB will be running in "locked" mode. silabs.com | Building a more connected world. Rev. 1.0 | 18 UG334: Si5394 Evaluation Board User's Guide Using the Si5394 EVB 10.5 Workflow Scenario 2: Modifying the Default Silicon Labs-Created Device Configuration To modify the "default" configuration using the CBPro Wizard, click on the links below under "Edit Configuration with Wizard". Figure 10.13. Edit Configuration with Wizard You will now be taken to the Wizard's step-by-step menus to allow you to change any of the default plan's operating configurations. silabs.com | Building a more connected world. Rev. 1.0 | 19 UG334: Si5394 Evaluation Board User's Guide Using the Si5394 EVB Figure 10.14. Design Wizard Note that you can click on the icon on the lower left hand corner of the menu to confirm if your frequency plan is valid. After making your desired changes, you can click on Write to EVB to update the DUT to reconfigure your device real-time. The Design Write status window will appear each time you make a change. Figure 10.15. Writing Design Status silabs.com | Building a more connected world. Rev. 1.0 | 20 UG334: Si5394 Evaluation Board User's Guide Using the Si5394 EVB 10.6 Workflow Scenario 3: Testing a User-Created Device Configuration To test a previously created user configuration, open the CBPro Wizard by clicking on the icon on your desktop and then selecting Open Design Project File. Figure 10.16. Open Design Project File Locate your CBPro design file (*.slabtimeproj or *.sitproj file).design file in the Windows file browser. Figure 10.17. Browse to Project File silabs.com | Building a more connected world. Rev. 1.0 | 21 UG334: Si5394 Evaluation Board User's Guide Using the Si5394 EVB Select "Yes" when the WRITE DESIGN to EVB popup appears: Figure 10.18. Write Design to EVB Dialog The progress bar will be launched. Once the new design project file has been written to the device, verify the presence and frequencies of your output clocks and other operating configurations using external instrumentation. silabs.com | Building a more connected world. Rev. 1.0 | 22 UG334: Si5394 Evaluation Board User's Guide Using the Si5394 EVB 10.7 Exporting the Register Map File for Device Programming by a Host Processor You can also export your configuration to a file format suitable for in-system programming by selecting Export as shown below: Figure 10.19. Export Register Map File You can now write your device's complete configuration to file formats suitable for in-system programming: Figure 10.20. Export Settings silabs.com | Building a more connected world. Rev. 1.0 | 23 UG334: Si5394 Evaluation Board User's Guide Writing a New Frequency Plan or Device Configuration to Non-Volatile Memory (OTP) 11. Writing a New Frequency Plan or Device Configuration to Non-Volatile Memory (OTP) Note: Writing to the device non-volatile memory (OTP) is NOT the same as writing a configuration into the Si5394 using ClockBuilder Pro on the Si5394 EVB. Writing a configuration into the EVB from ClockBuilderPro is done using Si5394 RAM space and can be done virtually unlimited numbers of times. Writing to OTP is limited as described below: Refer to the Si5394 Family Reference Manual and device data sheets for information on how to write a configuration to the EVB DUT's non-volatile memory (OTP). The OTP can be programmed a maximum of two times only. Care must be taken to ensure the configuration desired is valid when choosing to write to OTP. silabs.com | Building a more connected world. Rev. 1.0 | 24 UG334: Si5394 Evaluation Board User's Guide Serial Device Communications 12. Serial Device Communications 12.1 Onboard SPI Support The MCU onboard the Si5394 EVB communicates with the Si5394 device through a 4-wire SPI (Serial Peripheral Interface) link. The MCU is the SPI master and the Si5394 device is the SPI slave. The Si5394 device can also support a 2-wire I2C serial interface, although the Si5394 EVB does NOT support the I2C mode of operation. SPI mode was chosen for the EVB because of the relatively higher speed transfers supported by SPI vs. I2C. 12.2 External I2C Support I2C can be supported if driven from an external I2C controller. The serial interface signals between the MCU and Si5394 pass through shunts loaded on header J17. These jumper shunts must be installed in J17 for normal EVB operation using SPI with CBPro. If testing of I2C operation via external controller is desired, the shunts in J17 can be removed thereby isolating the on-board MCU from the Si5394 device. The shunt at JP1 (I2C_SEL) must also be removed to select I2C as Si5394 interface type. An external I2C controller connected to the Si5394 side of J17 can then communicate to the Si5394 device. (For more information on I2C signal protocol, please refer to the Si5394 data sheet.) The figure below illustrates the J17 header schematic. J17 even numbered pins (2, 4, 6, etc.) connect to the Si5394 device and the odd numbered pins (1, 3, 5, etc.) connect to the MCU. Once the jumper shunts have been removed from J17 and JP1, I2C operation should use J17 pin 4 (DUT_SDA_SDIO) as the I2C SDA and J17 pin 8 (DUT_SCLK) as the I2C SCLK. Please note the external I2C controller will need to supply its own I2C signal pull-up resistors. Figure 12.1. Serial Communications Header J17 silabs.com | Building a more connected world. Rev. 1.0 | 25 UG334: Si5394 Evaluation Board User's Guide Si5394 EVB Schematic, Layout, and Bill of Materials (BOM) 13. Si5394 EVB Schematic, Layout, and Bill of Materials (BOM) The Si5394 EVB Schematic, Layout, and Bill of Materials (BOM) can be found online at: http://www.silabs.com/products/clocksoscillators/pages/si539x-evb.aspx. Note: Please be aware that the Si5394 EVB schematic is in OrCad Capture hierarchical format and not in a typical "flat" schematic format. This document supports the evaluation board silkscreened Si5394 EVB for the following configurations as described in the table below. The data sheet documents the different Si5394 grades. Table 13.1. Evaluation Board Configurations1 Config # Eval Board Label Si5394 Notes Grade Revision 1 Si5394A-A-EB A A Crystal and related components installed. 2 Si5394P-A-EB P A Crystal and related components installed. Only the DUT and label differ versus Si5394A-A-EB. Note: 1. Note that it is not possible to load an Si5394A project onto an Si5394P-A-EB or an Si5394P project onto an Si5394A-A-EB. Use Si5394A/B/C/D plans for Si5394A-A-EB and Si5394P plans for Si5394P-A-EB. silabs.com | Building a more connected world. Rev. 1.0 | 26 ClockBuilder Pro One-click access to Timing tools, documentation, software, source code libraries & more. Available for Windows and iOS (CBGo only). www.silabs.com/CBPro Timing Portfolio www.silabs.com/timing SW/HW www.silabs.com/CBPro Quality www.silabs.com/quality Support and Community community.silabs.com Disclaimer Silicon Labs intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or intending to use the Silicon Labs products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Labs reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included information. Silicon Labs shall have no liability for the consequences of use of the information supplied herein. This document does not imply or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products are not designed or authorized to be used within any Life Support System without the specific written consent of Silicon Labs. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant personal injury or death. Silicon Labs products are not designed or authorized for military applications. Silicon Labs products shall under no circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons. Trademark Information Silicon Laboratories Inc.(R) , Silicon Laboratories(R), Silicon Labs(R), SiLabs(R) and the Silicon Labs logo(R), Bluegiga(R), Bluegiga Logo(R), Clockbuilder(R), CMEMS(R), DSPLL(R), EFM(R), EFM32(R), EFR, Ember(R), Energy Micro, Energy Micro logo and combinations thereof, "the world's most energy friendly microcontrollers", Ember(R), EZLink(R), EZRadio(R), EZRadioPRO(R), Gecko(R), ISOmodem(R), Micrium, Precision32(R), ProSLIC(R), Simplicity Studio(R), SiPHY(R), Telegesis, the Telegesis Logo(R), USBXpress(R), Zentri, Z-Wave, and others are trademarks or registered trademarks of Silicon Labs. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders. Silicon Laboratories Inc. 400 West Cesar Chavez Austin, TX 78701 USA http://www.silabs.com