VESD09A4A-HSF www.vishay.com Vishay Semiconductors 4-Line (Quad) ESD Protection Diode Array in LLP75-6L FEATURES 6 5 * Compact LLP75-6L package 4 * Low package height < 0.6 mm * 4-line ESD protection (quad) * Low leakage current < 0.1 A 1 2 3 * Low load capacitance CD = 6 pF 21002 20453 * ESD immunity acc. IEC 61000-4-2 8 kV contact discharge 10 kV air discharge 1 MARKING (example only) XX YY * Surge current acc. IEC 61000-4-5 IPP > 1.5 A * Soldering can be checked by standard vision inspection. No X-ray necessary 21001 * e4 - precious metal (e.g. Ag, Au, NiPd, NiPdAu) (no Sn) Dot = pin 1 marking XX = date code YY = type code (see table below) * Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 click logo to get started ORDERING CODE TAPED UNITS PER REEL (8 mm TAPE ON 7" REEL) MINIMUM ORDER QUANTITY VESD09A4A-HSF-GS08 3000 15 000 DESIGN SUPPORT TOOLS Models Available ORDERING INFORMATION DEVICE NAME VESD09A4A-HSF PACKAGE DATA DEVICE NAME PACKAGE TYPE NAME CODE VESD09A4A-HSF LLP75-6L 49 WEIGHT MOLDING COMPOUND FLAMMABILITY RATING MOISTURE SENSITIVITY LEVEL SOLDERING CONDITIONS 4.2 mg UL 94 V-0 MSL level 1 (according J-STD-020) Peak temperature max. 260 C ABSOLUTE MAXIMUM RATINGS VESD09A4A-HSF TEST CONDITIONS SYMBOL VALUE UNIT Peak pulse current BiAs-mode: each input (pin 1, 3 - 5) to ground (pin 2 and 6); acc. IEC 61000-4-5; tp = 8/20 s; single shot IPPM 1.5 A Peak pulse power BiAs-mode: each input (pin 1, 3 - 5) to ground (pin 2 and 6); acc. IEC 61000-4-5; tp = 8/20 s; single shot PPP 30 W Contact discharge acc. IEC 61000-4-2; 10 pulses BiAs-mode: each input (pin 1, 3 - 5) to ground (pin 2 and 6) VESD 8 kV Air discharge acc. IEC 61000-4-2; 10 pulses BiAs-mode: each input (pin 1, 3 - 5) to ground (pin 2 and 6) VESD 10 kV TJ -40 to +125 C TSTG -55 to +150 C PARAMETER ESD immunity Operating temperature Storage temperature Rev. 1.7, 04-Jan-2019 Junction temperature Document Number: 81834 1 For technical questions, contact: ESDprotection@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VESD09A4A-HSF www.vishay.com Vishay Semiconductors BiAs-MODE (4-line bidirectional asymmetrical protection mode) With the VESD09A4A-HSF up to 4 signal- or data-lines (L1 to L4) can be protected against voltage transients. With pin 2 connected to ground and pin 1, 3, 4 and 6 connected to a signal- or data-line which has to be protected. As long as the voltage level on the data- or signal-line is between 0 V (ground level) and the specified maximum reverse working voltage (VRWM) the protection diode between data line and ground offer a high isolation to the ground line. The protection device behaves like an open switch. As soon as any positive transient voltage signal exceeds the break through voltage level of the protection diode, the diode becomes conductive and shorts the transient current to ground. Now the protection device behaves like a closed switch. The clamping voltage (VC) is defined by the breakthrough voltage (VBR) level plus the voltage drop at the series impedance (resistance and inductance) of the protection device. Any negative transient signal will be clamped accordingly. The negative transient current is flowing in the forward direction of the protection diode. The low forward voltage (VF) clamps the negative transient close to the ground level. Due to the different clamping levels in forward and reverse direction the VESD09A4A-HSF clamping behaviour is bidirectional and asymmetrical (BiAs). L4 L3 6 5 4 1 2 3 L2 L1 21003 ELECTRICAL CHARACTERISTICS VESD09A4A-HSF (Pin 1, 3, 4, or 5 to pin 2) (Tamb = 25 C, unless otherwise specified) PARAMETER TEST CONDITIONS/REMARKS SYMBOL MIN. TYP. MAX. UNIT Number of lines which can be protected Nchannel - - 1 lines Max. reverse working voltage VRWM - - 9 V Reverse voltage at IR = 0.1 A VR 9 - - V Reverse current at VR = VRWM = 9 V IR - < 0.01 0.1 A Protection paths Reverse stand-off voltage Reverse breakdown voltage at IR = 1 mA VBR 11.2 13 V Reverse clamping voltage at IPP = 1.5 A, acc. IEC 61000-4-5 VC - 23 V Forward clamping voltage at IF = 1.5 A, acc. IEC 61000-4-5 VF - 2 V at VR = 0 V; f = 1 MHz CD - 6.2 10 pF at VR = 4.5 V; f = 1 MHz CD - 3.2 4 pF Capacitance Note * BiAs mode (between pin 1 and pin 2). If a higher surge current or peak pulse current (IPP) is needed, some protection diodes in the VESD09A4A-HSF can also be used in parallel in order to "multiply" the performance. If two diodes are switched in parallel you get * double surge power = double peak pulse current (2 x IPPM) * half of the line inductance = reduced clamping voltage * half of the line resistance = reduced clamping voltage * double line capacitance (2 x CD) * double reverse leakage current (2 x IR) 6 5 4 L2 L1 1 2 3 21004 Rev. 1.7, 04-Jan-2019 Document Number: 81834 2 For technical questions, contact: ESDprotection@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VESD09A4A-HSF www.vishay.com Vishay Semiconductors TYPICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) 100 8 s to 100 % 100 % 10 80 % 1 IF (mA) IPPM 60 % 20 s to 50 % 40 % 0.1 20 % 0.01 0% 0 10 20 30 Time (s) 20548 0.001 0.5 40 Fig. 1 - ESD Discharge Current Wave Form acc. IEC 61000-4-2 (330 /150 pF) 0.7 0.8 0.9 1 VF (V) Fig. 4 - Typical Forward Current IF vs. Forward Voltage VF 14 120 % Rise time = 0.7 ns to 1 ns 12 100 % 10 80 % 8 VR (V) Discharge Current IESD 0.6 20936 60 % 53 % 6 40 % 4 27 % 20 % 2 0% -10 0 10 20 30 40 50 60 70 80 90 100 Time (ns) 20557 0 0.01 0.1 1 20937 Fig. 2 - 8/20 s Peak Pulse Current Wave Form acc. IEC 61000-4-5 10 100 1000 10000 IR (A) Fig. 5 - Typical Reverse Voltage VR vs. Reverse Current IR 7 25 f = 1 MHz 6 20 positive surge 5 4 VC (V) CD (pF) 15 3 Measured acc. IEC 61000-4-5 (8/20 s - wave form) 10 VC 5 2 0 1 negative surge 0 -5 0 20935 2 4 6 8 10 VR (V) Fig. 3 - Typical Capacitance CD vs. Reverse Voltage VR Rev. 1.7, 04-Jan-2019 0 20938 1 2 IPP (A) Fig. 6 - Typical Peak Clamping Voltage VC vs. Peak Pulse Current IPP Document Number: 81834 3 For technical questions, contact: ESDprotection@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VESD09A4A-HSF www.vishay.com Vishay Semiconductors 120 acc. IEC 61000-4-2 + 8 kV contact discharge 100 VC-ESD (V) 80 60 40 20 0 - 20 - 10 0 10 20 30 40 50 60 70 80 90 t (ns) 20939 Fig. 7 - Typical Clamping Performance at + 8 kV Contact Discharge (acc. IEC 61000-4-2) 30 acc. IEC 61000-4-2 - 8 kV contact discharge 20 10 VC-ESD (V) 0 - 10 - 20 - 30 - 40 - 50 - 60 - 70 - 10 0 10 20 30 40 50 60 70 80 90 t (ns) 20940 Fig. 8 - Typical Clamping Performance at - 8 kV Contact Discharge (acc. IEC 61000-4-2) 120 acc. IEC 61000-4-2 contact discharge 100 80 positive discharge VC-ESD (V) 60 40 20 VC-ESD 0 - 20 - 40 negative discharge - 60 - 80 0 20941 2000 4000 6000 8000 10000 VESD (kV) Fig. 9 - Typical Peak Clamping Voltage at ESD Contact Discharge (acc. IEC 61000-4-2) Rev. 1.7, 04-Jan-2019 Document Number: 81834 4 For technical questions, contact: ESDprotection@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VESD09A4A-HSF www.vishay.com Vishay Semiconductors 0.45 (0.018) 0.55 (0.022) 0.2 (0.008) 0.3 (0.012) 0.2 (0.008) 0.3 (0.012) 1 (0.039) 0.2 (0.008) 0.3 (0.012) Heat sink 0.95 (0.037) 1.05 (0.041) PACKAGE DIMENSIONS in millimeters (Inches): LLP75-6L 0.5 (0.020) 0.6 (0.024) 0.54 (0.021) 0.60 (0.023) 0.05 (0.002) 0 (0.000) 0.15 (0.006) 0.25 (0.010) 1.65 (0.065) 1.55 (0.061) 1.55 (0.061) 1.65 (0.065) Pin 1 marking Foot print recommendation: 0.5 (0.020) 0.5 (0.020) 0.3 (0.012) 0.3 (0.012) Document no.:S8-V-3906.02-010 (4) Created - Date: 04. MAY 2005 Rev. 4 - Date: 21. March 2006 0.15 (0.006) 1 (0.039) 0.5 (0.020) 1 (0.039) 0.25 (0.010) 0.15 (0.006) Solder resist mask Solder pad 0.5 (0.020) 20454 Rev. 1.7, 04-Jan-2019 Document Number: 81834 5 For technical questions, contact: ESDprotection@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VESD09A4A-HSF www.vishay.com Vishay Semiconductors LLP75-6x S9 F5 Pad layout - view from top / seen at bottom side S8-V-3906.02-004 (4) 10.01.2005 Rev. 1.7, 04-Jan-2019 Pin 1 - location Document Number: 81834 6 For technical questions, contact: ESDprotection@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. (c) 2021 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2021 1 Document Number: 91000