W49F002U Data Sheet
256K × 8 CMOS FLASH MEMORY
Publication Release Date: April 19, 2005
- 1 - Revision A7
Table of Content-
1. GENERAL DESCRIPTION ......................................................................................................... 3
2. FEATURES ................................................................................................................................. 3
3. PIN CONFIGURATIONS............................................................................................................. 4
4. BLOCK DIAGRAM ...................................................................................................................... 4
5. PIN DESCRIPTION..................................................................................................................... 4
6. FUNCTIONAL DESCRIPTION.................................................................................................... 5
6.1 Device Operation ............................................................................................................ 5
6.1.1 Read Mode.......................................................................................................................5
6.1.2 Write Mode .......................................................................................................................5
6.1.3 Standby Mode ..................................................................................................................5
6.1.4 Output Disable Mode........................................................................................................5
6.1.5 Auto-select Mode..............................................................................................................5
6.1.6 Reset Mode: Hardware Reset ..........................................................................................6
6.2 Data Protection ............................................................................................................... 6
6.2.1 Low VDD Inhibit................................................................................................................6
6.2.2 Write Pulse "Glitch" Protection .........................................................................................6
6.2.3 Logical Inhibit ...................................................................................................................6
6.2.4 Power-up Write and Read Inhibit......................................................................................6
6.3 Command Definitions ..................................................................................................... 7
6.3.1 Read Command ...............................................................................................................7
6.3.2 Auto-select Command ......................................................................................................7
6.3.3 Byte Program Command..................................................................................................7
6.3.4 Chip Erase Command ......................................................................................................8
6.3.5 Sector Erase Command ...................................................................................................8
6.4 Write Operation Status ................................................................................................... 8
6.4.1 DQ7: Data Polling.............................................................................................................8
6.4.2 DQ6: Toggle Bit ................................................................................................................9
7. TABLE OF OPERATING MODES .............................................................................................. 9
7.1 Device Bus Operations ................................................................................................... 9
7.2 Auto-select Codes (High Voltage Method) ................................................................... 10
7.3 Embedded Programming Algorithm.............................................................................. 11
7.4 Embedded Erase Algorithm.......................................................................................... 12
7.5 Embedded #Data Polling Algorithm.............................................................................. 13
7.6 Embedded Toggle Bit Algorithm................................................................................... 13
7.7 Software Product Identification and Boot Block Lockout Detection Acquisition Flow .. 14
7.8 Boot Block Lockout Enable Acquisition Flow................................................................ 15
8. DC CHARACTERISTICS.......................................................................................................... 16
8.1 Absolute Maximum Ratings .......................................................................................... 16
8.2 DC Operating Characteristics ....................................................................................... 16
8.3 Power-up Timing........................................................................................................... 17
W49F002U
- 2 -
9. CAPACITANCE......................................................................................................................... 17
10. AC CHARACTERISTICS .......................................................................................................... 17
10.1 AC Test Conditions....................................................................................................... 17
10.2 AC Test Load and Waveform ....................................................................................... 17
10.3 Read Cycle Timing Parameters.................................................................................... 18
10.4 Write Cycle Timing Parameters .................................................................................... 18
10.5 Datah Polling and Toggle Bit Timing Parameters......................................................... 19
10.6 Reset Timing Parameters ............................................................................................. 19
11. TIMING WAVEFORMS ............................................................................................................. 20
11.1 Read Cycle Timing Diagram......................................................................................... 20
11.2 #WE Controlled Command Write Cycle Timing Diagram............................................. 20
11.3 #CE Controlled Command Write Cycle Timing Diagram.............................................. 21
11.4 Program Cycle Timing Diagram.................................................................................... 21
11.5 #DATA Polling Timing Diagram .................................................................................... 22
11.6 Toggle Bit Timing Diagram ........................................................................................... 22
11.7 Boot Block Lockout Enable Timing Diagram ................................................................ 23
11.8 Chip Erase Timing Diagram.......................................................................................... 23
11.9 Sector Erase Timing Diagram....................................................................................... 24
11.10 Reset Timing Diagram................................................................................................. 24
12. ORDERING INFORMATION..................................................................................................... 25
13. HOW TO READ THE TOP MARKING...................................................................................... 26
14. PACKAGE DIMENSIONS......................................................................................................... 27
14.1 32-pin P-DIP ................................................................................................................. 27
14.2 32-pin PLCC ................................................................................................................. 27
14.3 32-pin STSOP (8 x 14 mm) .......................................................................................... 28
14.4 32-pin TSOP (8 x 20 mm)............................................................................................. 28
15. VERSION HISTORY .................................................................................................................29
W49F002U
Publication Release Date: 8/10/2000
- 3 - Revision A2.1
1. GENERAL DESCRIPTION
The W49F002U is a 2-megabit, 5-volt only CMOS flash memory organized as 256K × 8 bits. The
device can be programmed and erased in-system with a standard 5V power supply. A 12-volt VPP is
not required. The unique cell architecture of the W49F002U results in fast program/erase operations
with extremely low current consumption (compared to other comparable 5-volt flash memory products).
The device can also be programmed and erased using standard EPROM programmers.
2. FEATURES
Single 5-volt operations:
5-volt Read
5-volt Erase
5-volt Program
Fast Program operation:
Byte-by-Byte programming: 35 µS (typ.)
Fast Erase operation: 100 mS (typ.)
Fast Read access time: 70/90/120 nS
Endurance: 10K cycles (typ.)
Ten-year data retention
Hardware data protection
One 16K byte Boot Block with Lockout
protection
Two 8K byte Parameter Blocks
Two Main Memory Blocks (96K, 128K) Bytes
Low power consumption
Active current: 25 mA (typ.)
Standby current: 20 µA (typ.)
Automatic program and erase timing with
internal VPP generation
End of program or erase detection
Toggle bit
Data polling
Latched address and data
TTL compatible I/O
JEDEC standard byte-wide pinouts
Available packages: 32-pin DIP, 32-pin
STSOP (8 mm × 14 mm), 32-pin TSOP
(8 mm × 20 mm) , 32-pin-PLCC
and 32-pin-PLCC Lead free
W49F002U
- 4 -
3. PIN CONFIGURATIONS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
DQ0
DQ1
DQ2
Vss
A7
A6
A5
A4
A3
A2
A1
A0
A16
A15
A12
V
#WE
A14
A13
A8
A9
A11
#OE
A10
#CE
DQ7
DQ6
DQ5
DQ4
DQ3
DD
A17
32-pin
DIP
#RESET
5
6
7
9
10
11
12
13
A7
A6
A5
A4
A3
A2
A1
A0
DQ0
29
28
27
26
25
24
23
22
21
3031
32
1
2
3
4
8
2019
18171615
14
D
Q
1
D
Q
2
V
s
s
D
Q
3
D
Q
4
D
Q
5
D
Q
6
A14
A13
A8
A9
A11
#OE
A10
#CE
DQ7
A
1
2
A
1
6
V
D
D
#
W
E
A
1
5
32-pin
PLCC
A
1
7
#
R
E
S
E
T
32-pin
TSOP
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
A15
A12
A7
A6
A5
A4
V
#WE
A14
A13
A8
DD
A11
A9
A16
A17
#RESET
A3
A2
A1
A0
DQ0
DQ1
DQ2
Vss
#OE
A10
#CE
DQ7
DQ6
DQ5
DQ4
DQ3
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
4. BLOCK DIAGRAM
CONTROL OUTPUT
BUFFER
DECODER
#CE
#OE
#WE
A0
.
.
A17
.
.
DQ0
V
DD
V
SS
DQ7
3FFFF
20000
1FFFF
38000
37FFF
3A000
39FFF
00000
3C000
3BFFF
PARAMETER
BLOCK2
8K BYTES
BOOT BLOCK
16K BYTES
PARAMETER
BLOCK1
8K BYTES
#RESET
MAIN MEMORY
BLOCK2
128K BYTES
MAIN MEMORY
BLOCK1
96K BYTES
5. PIN DESCRIPTION
SYMBOL PIN NAME
#RESET Reset
A0 A17 Address Inputs
DQ0 DQ7 Data Inputs/Outputs
#CE Chip Enable
#OE Output Enable
#WE Write Enable
VDD Power Supply
VSS Ground
W49F002U
Publication Release Date: April 19, 2005
- 5 - Revision A7
6. FUNCTIONAL DESCRIPTION
6.1 Device Operation
6.1.1 Read Mode
The read operation of the W49F002U is controlled by #CE and #OE, both of which have to be low for
the host to obtain data from the outputs. #CE is used for device selection. When #CE is high, the chip is
de-selected and only standby power will be consumed. #OE is the output control and is used to gate
data from the output pins. The data bus is in high impedance state when either #CE or #OE is high.
Refer to the timing waveforms for details.
6.1.2 Write Mode
Device erase and program are accomplished via the command register. The content of the register
serves as inputs to the internal state machine. The state machine outputs dictate the function of the
device.
The command register itself does not occupy any addressable memory location. The register is a latch
used to store the commands, along with the address and data information needed to execute the
command. The command register is written to bring #WE to logic low state when #CE is at logic low
state and #OE is at logic high state. Addresses are latched on the falling edge of #WE or #CE,
whichever happens later; while data is latched on the rising edge of #WE or #CE, whichever happens
first. Standard microprocessor write timings are used.
Refer to AC Write Characteristics and the Erase/Programming Waveforms for specific timing
parameters.
6.1.3 Standby Mode
There are two ways to implement the standby mode on the W49F002U device, both using the #CE pin.
A CMOS standby mode is achieved with the #CE input held at VDD -0.3V. Under this condition the current is
typically reduced to less than 100 µA. A TTL standby mode is achieved with the #CE pin held at VIH.
Under this condition the current is typically reduced to less than 3 mA.
In the standby mode the outputs are in the high impedance state, independent of the #OE input.
6.1.4 Output Disable Mode
With the #OE input at a logic high level (VIH), output from the device is disabled. This will cause the
output pins to be in a high impedance state.
6.1.5 Auto-select Mode
The auto-select mode allows the reading of a binary code from the device and will identify its
manufacturer and type. This mode is intended to be used by programming equipment for the purpose
of automatically matching the device to be programmed with its corresponding programming algorithm.
This mode is functional over the entire temperature range of the device.
To activate this mode, the programming equipment must force VID (11.5V to 12.5V) on address pin A9.
Two identifier bytes may then be sequenced from the device outputs by toggling address A0 from VIL to
VIH. All addresses are dont cares except A0 and A1 (see "Auto-select Codes"). Note: The hardware
SID read function is not included in all parts; please refer to Ordering Information for details.
The manufacturer and device codes may also be read via the command register; i.e., the W49F002U is
erased or programmed in a system without access to high voltage on the A9 pin. The command
sequence is illustrated in "Auto-select Codes".
W49F002U
- 6 -
Byte 0 (A0 = VIL) represents the manufacturers code (Winbond = DAh) and byte 1 (A0 = VIH) the
device identifier code (W49F002U = 0Bh,). All identifiers for manufacturer and device will exhibit odd
parity with DQ7 defined as the parity bit. In order to read the proper device codes when executing the
Auto-select, A1 must be VIL.
6.1.6 Reset Mode: Hardware Reset
The #RESET pin provides a hardware method of resetting the device to reading array data. When the
system drives the #RESET pin low for at least a period of tRP, the device immediately terminates any
operation in progress, tri-states all data output pins, and ignores all read/write attempts for the duration
of the #RESET pulse. The device also resets the internal state machine to reading array data. The
operation that was interrupted should be reinitiated once the device is ready to accept another
command sequence, to ensure data integrity.
Current is reduced for the duration of the #RESET pulse. When #RESET is held at VIL, the device
enters the TTL standby mode; if #RESET is held at Vss, the device enters the CMOS standby mode.
The #RESET pin may be tied to the system reset circuitry. A system reset would thus also reset the
Flash memory, enabling the system to read the boot-up firmware from the Flash memory.
6.2 Data Protection
The W49F002U is designed to offer protection against accidental erasure or programming caused by
spurious system level signals that may exist during power transitions. During power up the device
automatically resets the internal state machine in the Read mode. Also, with its control register
architecture, alteration of the memory contents only occurs after successful completion of specific
multi-bus cycle command sequences. The device also incorporates several features to prevent
inadvertent write cycles resulting from VDD power-up and power-down transitions or system noise.
6.2.1 Low VDD Inhibit
To avoid initiation of a write cycle during VDD power-up and power-down, the W49F002U locks out
when VDD < 2.5V. The write and read operations are inhibited when VDD is less than 2.5V typical. The
W49F002U ignores all write and read operations until VDD > 2.5V. The user must ensure that the
control pins are in the correct logic state when VDD > 2.5V to prevent unintentional writes.
6.2.2 Write Pulse "Glitch" Protection
Noise pulses of less than 10 nS (typical) on #OE, #OE, or #WE will not initiate a write cycle.
6.2.3 Logical Inhibit
Writing is inhibited by holding any one of #OE = VIL, #CE = VIH, or #WE = VIH. To initiate a write cycle
#CE and #WE must be a logical zero while #OE is a logical one.
6.2.4 Power-up Write and Read Inhibit
Power-up of the device with #WE = #CE = VIL and #OE = VIH will not accept commands on the rising
edge of #WE. The internal state machine is automatically reset to the read mode on power-up.
W49F002U
Publication Release Date: April 19, 2005
- 7 - Revision A7
6.3 Command Definitions
Device operations are selected by writing specific address and data sequences into the command
register. Writing incorrect address and data values or writing them in the improper sequence will reset
the device to the read mode. "Command Definitions" defines the valid register command sequences.
Moreover, both Reset/Read commands are functionally equivalent, resetting the device to the read
mode.
6.3.1 Read Command
The device will automatically power-up in the read state. In this case, a command sequence is not
required to read data. Standard microprocessor read cycles will retrieve array data. This default value
ensures that no spurious alteration of the memory content occurs during the power transition.
The device will automatically returns to read state after completing an Embedded Program or
Embedded Erase algorithm.
Refer to the AC Read Characteristics and Waveforms for the specific timing parameters.
6.3.2 Auto-select Command
Flash memories are intended for use in applications where the local CPU can alter memory contents.
As such, manufacture and device codes must be accessible while the device resides in the target
system. PROM programmers typically access the signature codes by raising A9 to a high voltage.
However, multiplexing high voltage onto the address lines is not generally a desirable system design
practice.
The device contains an auto-select command operation to supplement traditional PROM programming
methodology. The operation is initiated by writing the auto-select command sequence into the
command register. Following the command write, a read cycle from address XX00H retrieves the
manufacture code of DAh. A read cycle from address XX01H returns the device code (W49F002U =
0Bh).
6.3.3 Byte Program Command
The device is programmed on a byte-by-byte basis. Programming is a four-bus-cycle operation. The
program command sequence is initiated by writing two "unlock" write cycles, followed by the program
set-up command. The program address and data are written next, which in turn initiate the Embedded
program algorithm. Addresses are latched on the falling edge of #CE or #WE, whichever happens later
and the data is latched on the rising edge of #CE or #WE, whichever happens first. The rising edge of
#CE or #WE (whichever happens first) begins programming using the Embedded Program Algorithm.
Upon executing the algorithm, the system is not required to provide further controls or timings. The
device will automatically provide adequate internally generated program pulses and verify the
programmed cell margin.
The automatic programming operation is completed when the data on DQ7 (also used as Data Polling)
is equivalent to the data written to this bit at which time the device returns to the read mode and
addresses are no longer latched (see "Hardware Sequence Flags"). Therefore, the device requires that
a valid address to the device be supplied by the system at this particular instance of time for Data
Polling operations. Data Polling must be performed at the memory location which is being
programmed.
Any commands written to the chip during the Embedded Program Algorithm will be ignored. If a
hardware reset occurs during the programming operation, the data at that particular location will be
corrupted.
W49F002U
- 8 -
Programming is allowed in any sequence and across sector boundaries. Beware that a data "0" cannot
be programmed back to a "1". Only erase operations can convert "0"s to "1"s.
Refer to the Embedded Programming Algorithm using typical command strings and bus operations.
6.3.4 Chip Erase Command
Chip erase is a six-bus-cycle operation. There are two "unlock" write cycles. These are followed by
writing the "set-up" command. Two more "unlock" write cycles are then followed by the chip erase
command.
Chip erase does not require the user to program the device prior to erase. Upon executing the
Embedded Erase Algorithm command sequence the device will automatically erase and verify the
entire memory for an all one data pattern. The erase is performed sequentially on each sector at the
same time (see "Feature"). The system is not required to provide any controls or timings during these
operations.
The automatic erase begins on the rising edge of the last #WE pulse in the command sequence and
terminates when the data on DQ7 is "1" at which time the device returns to read the mode.
Refer to the Embedded Erase Algorithm using typical command strings and bus operations.
6.3.5 Sector Erase Command
Sector erase is a six bus cycle operation. There are two "unlock" write cycles. These are followed by
writing the "set-up" command. Two more "unlock" write cycles are then followed by the sector erase
command. The sector address (any address location within the desired sector) is latched on the falling
edge of #WE, while the command (30H) is latched on the rising edge of #WE.
Sector erase does not require the user to program the device prior to erase. When erasing a sector or
sectors the remaining unselected sectors are not affected. The system is not required to provide any
controls or timings during these operations.
The automatic sector erase begins after the rising edge of the #WE pulse for the last sector erase
command pulse and terminates when the data on DQ7, Data Polling, is "1."
Refer to the Embedded Erase Algorithm using typical command strings and bus operations.
6.4 Write Operation Status
6.4.1 DQ7: Data Polling
The W49F002U device features Data Polling as a method to indicate to the host that the embedded
algorithms are in progress or completed.
During the Embedded Program Algorithm, an attempt to read the device will produce the complement
of the data last written to DQ7. Upon completion of the Embedded Program Algorithm, an attempt to
read the device will produce the true data last written to DQ7.
During the Embedded Erase Algorithm, an attempt to read the device will produce a "0" at the DQ7
output. Upon completion of the Embedded Erase Algorithm, an attempt to read the device will produce
a "1" at the DQ7 output.
The flowchart for Data Polling (DQ7) is shown in "Data Polling Algorithm".
For chip erase, the Data Polling is valid after the rising edge of the sixth pulse in the six #WE write
pulse sequence. For sector erase, the Data Polling is valid after the last rising edge of the sector erase
#WE pulse.
Just prior to the completion of Embedded Algorithm operations DQ7 may change asynchronously while
the output enable (#OE) is asserted low. This means that the device is driving status information on
DQ7 at one instant of time and then that bytes valid data at the next instant of time. Depending on
when the system samples the DQ7 output, it may read the status or valid data. Even if the device has
W49F002U
Publication Release Date: April 19, 2005
- 9 - Revision A7
completed the Embedded Algorithm operations and DQ7 has a valid data, the data outputs on DQ0 –
DQ6 may be still invalid. The valid data on DQ0 DQ7 will be read on the successive read attempts.
The Data Polling feature is only active during the Embedded Programming Algorithm, Embedded Erase
Algorithm, or sector erase time-out (see "Command Definitions").
See " #DATA Polling During Embedded Algorithm Timing Diagrams".
6.4.2 DQ6: Toggle Bit
The W49F002U also features the "Toggle Bit" as a method to indicate to the host system that the
embedded algorithms are in progress or completed.
During an Embedded Program or Erase Algorithm cycle, successive attempts to read (#OE toggling)
data from the device at any address will result in DQ6 toggling between one and zero. Once the
Embedded Program or Erase Algorithm cycle is completed, DQ6 will stop toggling and valid data will be
read on the next successive attempt. During programming, the Toggle Bit is valid after the rising edge
of the fourth #WE pulse in the four write pulse sequence. For chip erase, the Toggle Bit is valid after the
rising edge of the sixth #WE pulse in the six write pulse sequence. For Sector erase, the Toggle Bit is
valid after the last rising edge of the sector erase #WE pulse. The Toggle Bit is active during the sector
erase time-out.
7. TABLE OF OPERATING MODES
7.1 Device Bus Operations
PIN
MODE #CE #OE #WE #RESET A0 A17 DQ0 DQ7
Read VIL VIL VIH VIH Ain Dout
Write VIL VIH VIL VIH Ain Din
VIH X VIL X X High Z/DOUT
Write Inhibit VIH X X VIH X High Z/DOUT
Standby VIH X X VIH X High Z
Output Disable VIL VIH VIH VIH X High Z
Reset X X X VIL X High Z
W49F002U
- 10 -
7.2 Auto-select Codes (High Voltage Method)
DESCRIPTION #CE #OE #WE OTHER
ADD A9 A1 A0 DQ7
TO DQ0
Manufacturer ID: Winbond VIL VIL VIH X VID VIL VIL DAh
Device ID: W49F002U
(Top Boot Block) VIL VIL VIH X VID VIL VIH 0Bh
Notes:
1. SA = Sector Address, X = Dont Care. Sector Protection Verification: 01h (protected); 00h (unprotected).
2. The hardware SID read function is not included in all parts; please refer to Ordering Information for details.
Hardware Sequence Flags
OPERATION DQ7
(NOTE) DQ6
Embedded Program Algorithm #DQ7 Toggle
Standard Mode Embedded Erase Algorithm 0 Toggle
Note: DQ7 require a valid address when reading status information. Refer to the appropriate subsection for further details.
Command Definition(1)
1TH CYCLE 2ND CYCLE 3RD CYCLE 4TH CYCLE 5TH CYCLE 6TH CYCLE
COMMAND
DESCRIPTION
NO. OF
CYCLES ADDR. DATA ADDR.
DATA
ADDR.
DATA
ADDR.
DATA
ADDR.
DATA
ADDR.
DATA
Read 1 AIN DOUT
Chip Erase 6 5555 AA 2AAA 55 5555 80 5555 AA 2AAA 55 5555 10
Sector Erase 6 5555 AA 2AAA 55 5555 80 5555 AA 2AAA 55 SA(3) 30
Byte Program 4 5555 AA 2AAA 55 5555 A0 AIN DIN
Boot Block Lockout 6 5555 AA 2AAA 55 5555 80 5555 AA 2AAA 55 5555 40
Product ID Entry 3 5555 AA 2AAA 55 5555 90
Product ID Exit (2) 3 5555 AA 2AAA 55 5555 F0
Product ID Exit (2) 1 XXXX F0
Notes:
1. Address Format: A14 A0 (Hex); Data Format: DQ7 DQ0 (Hex)
2. Either one of the two Product ID Exit commands can be used.
3. SA means: Sector Address
If SA is within 3C000 to 3FFFF (Boot Block address range), and the Boot Block programming lockout feature is activated,
nothing will happen and the device will go back to read mode after 100nS.
If the Boot Block programming lockout feature is not activated, this command will erase Boot Block.
If SA is within 3A000 to 3BFFF (Parameter Block1 address range), this command will erase PB1.
If SA is within 38000 to 39FFF (Parameter Block2 address range), this command will erase PB2.
If SA is within 20000 to 37FFF (Main Memory Block1 address range), this command will erase MMB1.
If SA is within 00000 to 1FFFF (Main Memory Block2 address range), this command will erase MMB2.
W49F002U
Publication Release Date: April 19, 2005
- 11 - Revision A7
7.3 Embedded Programming Algorithm
Start
Write Program Command Sequence
(see below)
Increment Address
Programming Completed
5555H/AAH
2AAAH/55H
5555H/A0H
Program Address/Program Data
#Data Polling/ Toggle bit
Last Address
?
No
Yes
Program Command Sequence (Address/Command):
Pause TBP
W49F002U
- 12 -
7.4 Embedded Erase Algorithm
Start
Write Erase Command Sequence
(see below)
Erasure Completed
#Data Polling or Toggle Bit
Successfully Completed
Chip Erase Command Sequence
5555H/AAH
5555H/AAH
2AAAH/55H
2AAAH/55H
5555H/80H
5555H/10H
(Address/Command):
5555H/AAH
5555H/AAH
2AAAH/55H
2AAAH/55H
5555H/80H
Sector Address/30H
(Address/Command):
Individual Sector Erase
Command Sequence
Pause TEC /TSEC
W49F002U
Publication Release Date: April 19, 2005
- 13 - Revision A7
7.5 Embedded #Data Polling Algorithm
Start
Read Byte
(DQ0 - DQ7)
Address = VA
Pass
DQ7 = Data
?
Yes
No
VA = Byte address for programming
= Any of the sector addresses within
the sector being erased during sector
erase operation
= Valid address equals any sector group
address during chip erase
7.6 Embedded Toggle Bit Algorithm
Start
Read Byte
(DQ0 - DQ7)
Address = Don't Care
DQ6 = Toggle
?
Yes
No
Pass
W49F002U
- 14 -
7.7 Software Product Identification and Boot Block Lockout Detection Acquisition
Flow
Product
Identification
Entry (1)
Load data 55
to
address 2AAA
Load data 90
to
address 5555
Pause 10 S
Product
Identification
and Boot Block
Lockout Detection
Mode (3)
Read address = 0000
data = 00DA
Read address = 0001
data = 00AE
Read address = 0002
data in DQ0 =1/0
(4)
Product
Identification Exit(6)
Load data 55
to
address 2AAA
Load data F0
to
address 5555
Normal Mode
(5)
(2)
(2)
Load data AA
to
address 5555
µ
Load data AA
to
address 5555
Pause 10 S
µ
Notes for software product identification/boot block lockout detection:
(1) Data Format: DQ15 DQ8 (Don't Care), DQ7 DQ0 (Hex); Address Format: A14 A0 (Hex)
(2) A1 A16 = VIL; manufacture code is read for A0 = VIL; device code is read for A0 = VIH.
(3) The device does not remain in identification and boot block lockout detection mode if power down.
(4) If the output data in DQ0 = 1, the boot block programming lockout feature is activated; if the output data in DQ0 = 0, the
lockout feature is inactivated and the block can be programmed.
(5) The device returns to standard operation mode.
(6) Optional 1-write cycle (write F0 hex at XXXX address) can be used to exit the product identification/boot block lockout
detection.
W49F002U
Publication Release Date: April 19, 2005
- 15 - Revision A7
7.8 Boot Block Lockout Enable Acquisition Flow
Boot Block Lockout
Feature Set Flow
Load data AA
to
address 5555
Load data 55
to
address 2AAA
Load data 80
to
address 5555
Load data AA
to
address 5555
Load data 55
to
address 2AAA
Load data 40
to
address 5555
Pause 200 mS
Exit
W49F002U
- 16 -
8. DC CHARACTERISTICS
8.1 Absolute Maximum Ratings
PARAMETER RATING UNIT
Power Supply Voltage to Vss Potential -0.5 to +7.0 V
Operating Temperature 0 to +70 °C
Storage Temperature -65 to +150 °C
D.C. Voltage on Any Pin to Ground Potential Except A9 -0.5 to VDD +1.0 V
Transient Voltage (<20 nS) on Any Pin to Ground Potential -1.0 to VDD +1.0 V
Voltage on A9 Pin to Ground Potential -0.5 to 12.5 V
Note: Exposure to conditions beyond those listed under Absolute Maximum Ratings may adversely affect the life and reliability
of the device.
8.2 DC Operating Characteristics
(VDD = 5.0V ±10%, VSS = 0V, TA = 0 to 70° C)
LIMITS
PARAMETER SYM. TEST CONDITIONS
MIN. TYP. MAX.
UNIT
Power Supply
Current ICC
#CE = #OE = VIL, #WE = VIH,
all DQs open
Address inputs = VIL/VIH, at f = 5 MHz
- 25 50 mA
Standby VDD Current
(TTL input)
ISB1
#CE = VIH, all DQs open
Other inputs = VIL/VIH - 2 3 mA
Standby VDD Current
(CMOS input) ISB2 #CE = VDD -0.3V, all DQs open
Other inputs = VDD -0.3V/ Vss - 20 100 µA
Input Leakage
Current ILI VIN = Vss to VDD - - 10
µA
Output Leakage
Current ILO VOUT = Vss to VDD - - 10
µA
Input Low Voltage VIL - -0.3 - 0.8 V
Input High Voltage VIH - 2.0 - VDD +0.5 V
Output Low Voltage VOL IOL = 2.1 mA - - 0.45 V
Output High Voltage VOH IOH = -0.4 mA 2.4 - - V
W49F002U
Publication Release Date: April 19, 2005
- 17 - Revision A7
8.3 Power-up Timing
PARAMETER SYMBOL TYPICAL UNIT
Power-up to Read Operation TPU. READ 100 µS
Power-up to Write Operation TPU. WRITE 5 mS
9. CAPACITANCE
(VDD = 5.0V, TA = 25° C, f = 1 MHz)
PARAMETER SYMBOL CONDITIONS MAX. UNIT
I/O Pin Capacitance CI/O VI/O = 0V 12 pF
Input Capacitance CIN VIN = 0V 6 pF
10. AC CHARACTERISTICS
10.1 AC Test Conditions
PARAMETER CONDITIONS
Input Pulse Levels 0V to 3V
Input Rise/Fall Time <5 nS
Input/Output Timing Level 1.5V / 1.5V
Output Load 1 TTL Gate and CL = 30pF (for 70 nS/ 90 nS), 100 pF (for 120 nS)
10.2 AC Test Load and Waveform
+5V
1.8K
1.3K
DOUT
30 pF for 70nS / 90nS
(Including Jig and Scope)
Input
3V
0V
Test Point Test Point
1.5V 1.5V
Output
100 pF for 120nS
W49F002U
- 18 -
AC Characteristics, continued
10.3 Read Cycle Timing Parameters
(VDD = 5.0V ±10%, VDD = 0V, TA = 0 to 70° C)
W49F002U-70 W49F002U-90 W49F002U-120
PARAMETER SYM.
MIN. MAX. MIN. MAX. MIN. MAX.
UNIT
Read Cycle Time TRC 70 - 90 - 120 - nS
Chip Enable Access Time TCE - 70 - 90 - 120 nS
Address Access Time TAA - 70 - 90 - 120 nS
Output Enable Access Time TOE - 35 - 40 - 50 nS
#CE Low to Active Output TCLZ 0 - 0 - 0 - nS
#OE Low to Active Output TOLZ 0 - 0 - 0 - nS
#CE High to High-Z Output TCHZ - 25 - 25 - 30 nS
#OE High to High-Z Output TOHZ - 25 - 25 - 30 nS
Output Hold from Address Change TOH 0 - 0 - 0 - nS
10.4 Write Cycle Timing Parameters
PARAMETER SYMBOL MIN. TYP. MAX. UNIT
Address Setup Time TAS 0 - - nS
Address Hold Time TAH 50 - - nS
#WE and #CE Setup Time TCS 0 - - nS
#WE and #CE Hold Time TCH 0 - - nS
#OE High Setup Time TOES 0 - - nS
#OE High Hold Time TOEH 0 - - nS
#CE Pulse Width TCP 100 - - nS
#WE Pulse Width TWP 100 - - nS
#WE High Width TWPH 100 - - nS
Data Setup Time TDS 50 - - nS
Data Hold Time TDH 10 - - nS
Byte Programming Time TBP - 35 50
µS
Erase Cycle Time TEC - 0.1 0.2 S
Note: All AC timing signals observe the following guidelines for determining setup and hold times:
(a) High level signal's reference level is VIH and (b) low level signal's reference level is VIL.
W49F002U
Publication Release Date: April 19, 2005
- 19 - Revision A7
AC Characteristics, continued
10.5 Datah Polling and Toggle Bit Timing Parameters
W49F002U-70 W49F002U-90 W49F002U-120
PARAMETER SYM.
MIN. MAX. MIN. MAX. MIN. MAX.
UNIT
#OE to Data Polling Output Delay TOEP - 35 - 40 - 50 nS
#CE to Data Polling Output Delay TCEP - 70 - 90 - 120 nS
#OE to Toggle Bit Output Delay TOET - 35 - 40 - 50 nS
#CE to Toggle Bit Output Delay TCET - 70 - 90 - 120 nS
10.6 Reset Timing Parameters
PARAMETER SYMBOL MIN. TYP. MAX. UNIT
VDD stable to Reset Active TPRST 1 - - mS
Reset Pulse Width TRSTP 500 - - nS
Reset Active to Output Float TRSTF - - 50 nS
Reset Inactive to Input Active TRST 1 - -
µS
W49F002U
- 20 -
11. TIMING WAVEFORMS
11.1 Read Cycle Timing Diagram
Address A17-0
DQ7-0 Data Valid
Data Valid
High-Z
#CE
#OE
#WE
T
RC
V
IH
TCLZ
TOLZ
TOE
T
CE
T
OH
TAA
TCHZ
TOHZ
High-Z
11.2 #WE Controlled Command Write Cycle Timing Diagram
#CE
#OE
#WE
TCS
TOES
TCH
TOEH
TWPH
TWP
TDS
DQ7-0 Data Valid
TDH
Address A17-0
TAS TAH
W49F002U
Publication Release Date: April 19, 2005
- 21 - Revision A7
Timing Waveforms, continued
11.3 #CE Controlled Command Write Cycle Timing Diagram
High Z Data Valid
#CE
#OE
#WE
DQ7-0
TAS TAH
TCPH
TOEH
TDH
TDS
TCP
TOES
Address A17-0
11.4 Program Cycle Timing Diagram
Address A17-0
Byte 0 Byte 1
Byte 2 Internal Write Start
DQ7-0
#CE
#OE
#WE
Byte Program Cycle
TBP
TWPH
TWP
5555 55552AAA
AA A055
Address
Data-In
Byte 3
W49F002U
- 22 -
Timing Waveforms, continued
11.5 #DATA Polling Timing Diagram
Address A17-0
DQ7
#WE
#OE
#CE
X X X X
TCEP
TOEH
TOEP
TOES
TEC
TBP or
An An An An
11.6 Toggle Bit Timing Diagram
Address A17-0
DQ6
#CE
#OE
#WE
TOEH TOES
T
BP or
T
EC
W49F002U
Publication Release Date: April 19, 2005
- 23 - Revision A7
Timing Waveforms, continued
11.7 Boot Block Lockout Enable Timing Diagram
SB2
SB1
SB0
Address A17-0
DQ7-0
#CE
#OE
#WE
SB3 SB4 SB5
Six byte code for Boot Block
Lockout Feature Enable
T
EC
TWP
TWPH
5555 2AAA 5555 5555 2AAA 5555
AA 55 80 AA 55 40
11.8 Chip Erase Timing Diagram
SB2
SB1
SB0
Address A17-0
DQ7-0
#CE
#OE
#WE
SB3 SB4 SB5 Internal Erase starts
Six-byte code for 5V-only softwar
e
chip erase
TWP
TWPH
TEC
5555 2AAA 5555 5555 2AAA 5555
AA 55 80 AA 55 10
W49F002U
- 24 -
Timing Waveforms, continued
11.9 Sector Erase Timing Diagram
SB2
SB1
SB0
Address A17-0
DQ7-0
#CE
#OE
#WE
SB3 SB4 SB5 Internal Erase starts
Six-byte code for 5V-only software
Main Memory Erase
TWP
TWPH
TEC
5555 2AAA 5555 5555 2AAA SA
AA 55 80 AA 55 30
SA = Sector Address
11.10 Reset Timing Diagram
TRSTP
VDD T
PRST
#RESET
DQ7-0
T
RSTF TRST
Address A17-0
W49F002U
Publication Release Date: April 19, 2005
- 25 - Revision A7
12. ORDERING INFORMATION
PART NO.
ACCES
S TIME
(nS)
POWER
SUPPLY
CURRENT
MAX. (mA)
STANDBY
VDD
CURRENT
MAX. (µA)
PACKAGE CYCLE
HARDWARE
SID READ
FUNCTION
W49F002U-70B 70 50 100 (CMOS) 32-pin DIP 10K Y
W49F002U-90B 90 50 100 (CMOS) 32-pin DIP 10K Y
W49F002U-12B 120 50 100 (CMOS) 32-pin DIP 10K Y
W49F002UT70B 70 50 100 (CMOS) 32-pin TSOP (8 mm × 20 mm) 10K Y
W49F002UT90B 90 50 100 (CMOS) 32-pin TSOP (8 mm × 20 mm) 10K Y
W49F002UT12B 120 50 100 (CMOS) 32-pin TSOP (8 mm × 20 mm) 10K Y
W49F002UP70B 70 50 100 (CMOS) 32-pin PLCC 10K Y
W49F002UP90B 90 50 100 (CMOS) 32-pin PLCC 10K Y
W49F002UP12B 120 50 100 (CMOS) 32-pin PLCC 10K Y
W49F002UQ70B 70 50 100 (CMOS) 32-pin STSOP (8 mm × 14 mm) 10K Y
W49F002UQ90B 90 50 100 (CMOS) 32-pin STSOP (8 mm × 14 mm) 10K Y
W49F002UQ12B 120 50 100 (CMOS) 32-pin STSOP (8 mm × 14 mm) 10K Y
W49F002U70BN 70 50 100 (CMOS) 32-pin DIP 10K N
W49F002U90BN 90 50 100 (CMOS) 32-pin DIP 10K N
W49F002U12BN 120 50 100 (CMOS) 32-pin DIP 10K N
W49F002UT70N 70 50 100 (CMOS) 32-pin TSOP (8 mm × 20 mm) 10K N
W49F002UT90N 90 50 100 (CMOS) 32-pin TSOP (8 mm × 20 mm) 10K N
W49F002UT12N 120 50 100 (CMOS) 32-pin TSOP (8 mm × 20 mm) 10K N
W49F002UP70N 70 50 100 (CMOS) 32-pin PLCC 10K N
W49F002UP90N 90 50 100 (CMOS) 32-pin PLCC 10K N
W49F002UP12N 120 50 100 (CMOS) 32-pin PLCC 10K N
W49F002UQ70N 70 50 100 (CMOS) 32-pin STSOP (8 mm × 14 mm) 10K N
W49F002UQ90N 90 50 100 (CMOS) 32-pin STSOP (8 mm × 14 mm) 10K N
W49F002UQ12N 120 50 100 (CMOS) 32-pin STSOP (8 mm × 14 mm) 10K N
W49F002UP12Z 120 50 100 (CMOS) 32-pin PLCC Lead free 10K Y
Notes:
1. Winbond reserves the right to make changes to its products without prior notice.
2. Purchasers are responsible for performing appropriate quality assurance testing on products intended for use in
applications where personal injury might occur as a consequence of product failure.
3. Winbond offers Top Boot Block device, if any of Bottom Boot Block devices is required, please contact Winbond FAEs.
4. In Hardware SID read function column: Y = with SID read function; N = without SID read function.
W49F002U
- 26 -
13. HOW TO READ THE TOP MARKING
Example: The top marking of 48-pin TSOP W49F002UT70B
1st line: winbond logo
2nd line: the part number: W49F002UT70B
3rd line: the lot number
4th line: the tracking code: 149 O B SA
149: Packages made in ’01, week 49
O: Assembly house ID: A means ASE, O means OSE, ...etc.
B: IC revision; A means version A, B means version B, ...etc.
SA: Process code
W49F002UT70B
2138977A-A12
149OBSA
W49F002U
Publication Release Date: April 19, 2005
- 27 - Revision A7
14. PACKAGE DIMENSIONS
14.1 32-pin P-DIP
1.Dimensions D Max. & S include mold flash or
tie bar burrs.
2.Dimension E1 does not include interlead flash.
3.Dimensions D & E1 include mold mismatch an
d
are determined at the mold parting line.
6.General appearance spec. should be based o
n
final visual inspection spec.
.
1.371.22
0.0540.048
Notes:
Symbol Min. Nom. Max. Max.
Nom.
Min.
Dimension in inches Dimension in mm
A
B
c
D
e
A
L
S
A
A
1
2
E
0.050 1.27
0.210 5.33
0.010
0.150
0.016
0.155
0.018
0.160
0.022
3.81
0.41
0.25
3.94
0.46
4.06
0.56
0.008
0.120
0.670
0.010
0.130
0.014
0.140
0.20
3.05
0.25
3.30
0.36
3.56
0.555
0.550
0.545 14.10
13.97
13.84
17.02
15.24
14.99 15.49
0.6000.590 0.610
2.29 2.54 2.790.090 0.100 0.110
B1
1
e
E1
a
1.650 1.660 41.91 42.16
015
0.085 2.16
0.650
0.630 16.00 16.51
protrusion/intrusion.
4.Dimension B1 does not include dambar
5.Controlling dimension: Inches
150
Seating Plane
eA
2
A
a
c
E
Base Plane
1
A
1
e
L
A
S
1
E
D
1
B
B
32
116
17
14.2 32-pin PLCC
Notes:
L
c
1b
2
A
H
E
E
eb
DHD
y
A
A1
Seating Plane
E
G
GD
1
13
14 20
29
32
4
5
21
30
1. Dimensions D & E do not include interlead flash.
2. Dimension b1 does not include dambar protrusion/intrusion.
3. Controlling dimension: Inches
4. General appearance spec. should be based on final
visual inspection sepc.
Symbol Min. Nom. Max. Max.Nom.Min.
Dimension in Inches Dimension in mm
A
b
c
D
e
HE
L
y
A
A
1
2
E
b1
GD
3.56
0.50
2.802.67 2.93
0.71
0.66 0.81
0.41 0.46 0.56
0.20 0.25 0.35
13.89 13.97 14.05
11.35 11.43 11.51
1.27
HD
GE
12.45 12.9
5
13.46
9.91 10.41 10.92
14.86 14.99 15.11
12.32 12.45 12.57
1.91 2.29
0.004
0.095
0.090
0.075
0.495
0.49
0
0.485
0.595
0.590
0.585
0.430
0.410
0.390
0.530
0.51
0.490
0.050
0.453
0.450
0.447
0.553
0.550
0.547
0.014
0.010
0.008
0.022
0.018
0.016
0.0320.026 0.028
0.1150.105 0.110
0.020
0.140
1.12 1.420.044 0.056
0 10100
0.10
2.41
θ
θ
W49F002U
- 28 -
Package Dimensions, continued
14.3 32-pin STSOP (8 x 14 mm)
Min.
Dimension in Inches
Nom. Max. Min. Nom. Max.
Symbol
1.20
0.05 0.15
1.05
1.00
0.95
0.17
0.10
0.50
0.00
0
0.22 0.27
----- 0.21
12.40
8.00
14.00
0.50
0.60 0.70
0.80
0.10
35
0.047
0.006
0.041
0.040
0.035
0.007 0.009 0.010
0.004 ----- 0.008
0.488
0.315
0.551
0.020
0.020 0.024 0.028
0.031
0.000 0.004
035
0.002
A
A
b
c
D
E
e
L
L
Y
1
1
2
A
HD
θ
Dimension in mm
A
A
A2
1
L
L1
Y
E
H
D
D
c
θ
b
e
14.4 32-pin TSOP (8 x 20 mm)
A
A
A
2
1
L
L1
Y
c
E
H
D
D
b
e
M
0.10(0.004)
θ
Min. Nom. Max. Min. Nom. Max.
Symbol
A
A
b
c
D
E
e
L
L
Y
1
1
2
A
HD
Note:
Controlling dimension: Millimeters
Dimension in Inches
0.047
0.006
0.041
0.039
0.037
0.007 0.008 0.009
0.005 0.006 0.007
0.720 0.724 0.728
0.311 0.315 0.319
0.780 0.787 0.795
0.020
0.016 0.020 0.024
0.031
0.000 0.004
135
0.002
1.20
0.05 0.15
1.051.00
0.95
0.17
0.12
18.30
7.90
19.80
0.40
0.00
1
0.20 0.23
0.15 0.17
18.40 18.50
8.00 8.10
20.00 20.20
0.50
0.50 0.60
0.80
0.10
35
Dimension in mm
θ
__ __ __ __
__ __
__ __
__ __
__
__
__
__
__
__
W49F002U
Publication Release Date: April 19, 2005
- 29 - Revision A7
15. VERSION HISTORY
VERSION DATE PAGE DESCRIPTION
A1 Nov. 1999 - Renamed from W49F002/B/U/N
A2 Apr. 2000
1, 13 15, 20 Add the 120 nS bin
14
Change Tbp(typ.) from 10 µS to 35 µS
Change Tec (max.) from 1 Sec to 0.2 Sec
A3 Dec. 2000 All Modify some function description
3, 9, 25 Add in Hardware SID read note
1, 25, 27 Add in 32-pin TSOP (8 mm x 14 mm) package
A4 Jan. 2001 All Typo correction
A5 Aug. 13, 2001 16,22 Add Reset Timing Parameters and Diagram
A6 Feb. 21, 2002 1, 25, 28 Rename STOP (8 x 14 mm) as STSOP (8 x 14 mm)
4 Modify Low VDD Write Inhibit description
13
A
dd in Software Product Identification and Boot Block
Lockout Detection Acquisition Flow
14 Add in Boot Block Lockout Enable Acquisition Flow
24 Add HOW TO READ THE TOP MARKING
A7 April 19, 2005 1, 24 Addition 32 PLCC Lead free package
Important Notice
Winbond products are not designed, intended, authorized or warranted for use as components
in systems or equipment intended for surgical implantation, atomic energy control instruments,
airplane or spaceship instruments, transportation instruments, traffic signal instruments,
combustion control instruments, or for other applications intended to support or sustain life.
Further more, Winbond products are not intended for applications wherein failure of Winbond
products could result or lead to a situation wherein personal injury, death or severe property or
environmental damage could occur.
Winbond customers using or selling these products for use in such applications do so at their
own risk and agree to fully indemnify Winbond for any damages resulting from such improper
use or sales.
W49F002U
- 30 -
Headquarters
No. 4, Creation Rd. III,
Science-Based Industrial Park,
Hsinchu, Taiwan
TEL: 886-3-5770066
FAX: 886-3-5665577
http://www.winbond.com.tw/
Taipei Office
TEL: 886-2-8177-7168
FAX: 886-2-8751-3579
Winbond Electronics Corporation America
2727 North First Street, San Jose,
CA 95134, U.S.A.
TEL: 1-408-9436666
FAX: 1-408-5441798
Winbond Electronics (H.K.) Ltd.
No. 378 Kwun Tong Rd.,
Kowloon, Hong Kong
FAX: 852-27552064
Unit 9-15, 22F, Millennium City,
TEL: 852-27513100
Please note that all data and specifications are subject to change without notice.
All the trade marks of products and companies mentioned in this data sheet belong to their respective owners.
Winbond Electronics (Shanghai) Ltd.
200336 China
FAX: 86-21-62365998
27F, 2299 Yan An W. Rd. Shanghai,
TEL: 86-21-62365999
Winbond Electronics Corporation Japan
Shinyokohama Kohoku-ku,
Yokohama, 222-0033
FAX: 81-45-4781800
7F Daini-ueno BLDG, 3-7-18
TEL: 81-45-4781881
9F, No.480, Rueiguang Rd.,
Neihu Chiu, Taipei, 114,
Taiwan, R.O.C.