GLS85LD1001T / GLS85LD512 Industrial Grade PATA NANDriveTM Fact Sheet 01.000 October 2012 Features Industry Standard ATA / IDE Bus Interface - Host Interface: 16-bit access 1) - Supports up to PIO Mode-6 2) - Supports up to Multi-Word DMA Mode-4 - Supports up to Ultra DMA Mode-4 Performance - Sustained sequential data read Up to 30 MByte/sec* - Sustained sequential data write Up to 10 MByte/sec* Expanded Data Protection - WP#/PD# pin configurable by firmware for prevention of data overwrites Integrated Voltage Detector - Detects supply voltage fluctuations and generates reset during power-up and powerdown to prevent inadvertent writes 20-Byte Unique ID for Enhanced Security - Factory Pre-programmed 10-Byte Unique ID - User-Programmable 10-Byte ID Integrated Voltage Detector - Prevents inadvertent Write operations due to unexpected power-down or brownout. Pre-programmed Embedded Firmware - Executes industry standard ATA/IDE commands - Implements dynamic wear-leveling algorithms to substantially increase the longevity of flash media - Embedded Flash File System Industrial Temperature Range - -40C to 85C for industrial operation Package - 12mm x 24mm x 1.40mm (maximum height), 91-ball, 1.0mm ball pitch, LBGA (LBTE) All Devices are RoHS Compliant * measured using 128 KByte block size Power Management - 3.3V Power Supply - 5.0V or 3.3V Host Interface Through VDDQ pins - Immediate disabling of unused circuitry without host intervention - Zero wake-up latency Power Specification - Active mode 85mA typical (GLS85LD0512) 100mA typical (GLS85LD1001T) - Sleep mode 160A typical (GLS85LD0512) 170A typical (GLS85LD1001T) Robust Built-in ECC Product Description The GLS85LD0512 and GLS85LD1001T Industrial Grade PATA NANDriveTM devices (referred to as "PATA NANDrive" in this datasheet) are high-performance, fully integrated, embedded flash solid state drives. They combine an integrated ATA Controller and 512 MByte or 1 GByte of NAND flash memory in a multi-chip package. These products are ideal for solid-state mass storage in embedded and portable applications that require smaller form-factor and more reliable data storage. The integrated NAND flash controller with built-in advanced NAND management firmware communicates with the Host through the standard ATA protocol. It does not require any additional or proprietary software such as the Flash File System (FFS) and Memory Technology Driver (MTD). The PATA NANDrive provides a WP#/PD# pin to protect critical information stored in the flash media from unauthorized overwrites. The PATA NANDrive is preprogrammed with a 10-Byte unique serial ID and has the option of programming an additional 10-Byte serial ID for even greater system security. ATA-based solid-state mass storage technology is widely used in GPS and telematics, in-vehicle infotainment, portable and industrial computers, handheld data collection scanners, point-of-sale terminals, networking and telecommunications equipment, robotics, audio and video recorders, monitoring devices and set-top boxes. The PATA NANDrive's advanced NAND management technology enhances data security, improves endurance and accurately predicts the remaining lifespan of the NAND flash devices. This innovative technology combines robust NAND controller hardware error correction capabilities with advanced wear-leveling algorithms and bad block management to significantly extend the life of the product. The PATA NANDrive is a single device, solid state drive designed for embedded ATA/IDE protocol systems and supports standard ATA/IDE protocol with up to PIO Mode1) 2) 6 , Multi-Word DMA Mode-4 and Ultra DMA Mode-4 interface. The PATA NANDrive device provides complete IDE hard disk drive functionality and compatibility in a 12 mm x 24 mm LBGA package for easy, space-saving mounting to a system motherboard. These products surpass traditional storage in their small size, security, reliability, ruggedness and low power consumption. These specifications are subject to change without notice. (c) 2012 Greenliant Systems 1) 2) 1 PATA NANDrive is capable of supporting PIO Mode-6, but IdentifyDrive information report will show PIO Mode-4 PATA NANDrive is capable of supporting Multi-Word DMA Mode-4, but Identify-Drive information report will show MWDMA Mode-2 10/30/2012 S71382-F GLS85LD1001T / GLS85LD512 Industrial Grade PATA NANDriveTM Fact Sheet 01.000 October 2012 1.0 GENERAL DESCRIPTION Each PATA NANDrive contains an integrated PATA NAND flash memory controller and discrete NAND flash die(s) in a LBGA package. Refer to Figure 2-1 for the PATA NANDrive block diagram. 1.1 1.1.6 Error Correction Code (ECC) High performance is achieved through optimized hardware error detection and correction. Optimized PATA NANDrive The heart of the PATA NANDrive is the PATA NAND flash memory controller, which translates standard PATA signals into flash media data and control signals. The following components contribute to the PATA NANDrive's operation. 1.1.7 Serial Communication Interface (SCI) The Serial Communication Interface (SCI) is designed for manufacturing error reporting. During the design process, always provide access to the SCI port in the PCB design to aid in design validation. 1.1.1 Microcontroller Unit (MCU) The MCU transfers the ATA/IDE commands into data and control signals required for flash media operation. 1.1.8 Multi-tasking Interface The multi-tasking interface enables fast, sustained write performance by allowing concurrent Read, Program and Erase operations to multiple flash media devices. 1.1.2 Internal Direct Memory Access (DMA) The PATA NANDrive uses internal DMA allowing instant data transfer from/to buffer to/from flash media. This implementation eliminates microcontroller overhead associated with the traditional, firmwarebased approach, thereby increasing the data transfer rate. 1.2 Advanced NAND Management 1.1.3 Power Management Unit (PMU) The PMU controls the power consumption of the PATA NANDrive. The PMU dramatically reduces the power consumption of the PATA NANDrive by putting the part of the circuitry that is not in operation into sleep mode. Advanced NAND management technology balances the wear on erased blocks with an advanced wearleveling scheme. Advanced NAND management technology tracks the number of program/erase cycles within a group. When the Host updates data, higher priority is given to the less frequently written erase blocks; thereby, evenly distributing host writes within a wear-leveling group. 1.1.4 SRAM Buffer A key contributor to the PATA NANDrive performance is an SRAM buffer. The buffer optimizes the Host's data transfer to and from the flash media. Advanced NAND management technology enhances the PATA NANDrive security with password protection and four independent protection zones, which can be set to Read-only or Hidden. 1.1.5 Embedded Flash File System The embedded flash file system is an integral part of the PATA NANDrive. It contains MCU firmware that performs the following tasks: 1. Translates host side signals into flash media writes and reads 2. Provides flash media wear leveling to spread the flash writes to increase the longevity of flash media 3. Keeps track of data file structures These specifications are subject to change without notice. (c) 2012 Greenliant Systems 2 10/30/2012 S71382-F GLS85LD1001T / GLS85LD512 Industrial Grade PATA NANDriveTM Fact Sheet 01.000 October 2012 2.0 FUNCTION BLOCKS Figure 2-1: PATA NANDrive Block Diagram 3.0 PIN ASSIGNMENT The signal/pin assignments are listed in Table 3-1. Low active signals have a "#" suffix. Pin types are Input, Output or Input/Output. Signals that the Host sources are designated as inputs, while signals that the PATA NANDrive sources are outputs. Figure 3-1: Pin Assignments for 91-Ball LBGA These specifications are subject to change without notice. (c) 2012 Greenliant Systems 3 10/30/2012 S71382-F GLS85LD1001T / GLS85LD512 Industrial Grade PATA NANDriveTM Fact Sheet 01.000 October 2012 Table 3-1: Pin Assignments (1 of 2) Pin No. Pin Symbol Type 91-Ball Host Side Interface A2 K8 A1 K3 I A0 L2 D15 H8 D14 G9 D13 G8 D12 H7 D11 F9 D10 F8 D9 E8 D8 F7 I/O D7 F4 D6 H4 D5 E3 D4 H3 D3 F3 D2 G3 D1 F2 D0 G2 DMACK# K2 I DMARQ J3 O CS1FX# L3 I/O Type I1Z I1Z/O2 I2U O1 I2Z CS3FX# L8 I CSEL L9 I I1U IORD# H2 I I2Z IOWR# H9 I I2Z These specifications are subject to change without notice. (c) 2012 Greenliant Systems Name and Functions A[2:0] are used to select one of eight registers in the Task File. D[15:0] Data bus DMA Acknowledge - input from Host DMA Request to Host CS1FX# is the chip select for the task file registers CS3FX# is used to select the alternate status register and the Device Control register. This internally pulled-up signal is used to configure this device as a Master or a Slave. When this pin is grounded, this device is configured as a Master. When the pin is open, this device is configured as a Slave. The pin setting should remain the same from Power-on to Power-down. IORD#: This is an I/O Read Strobe generated by the Host. When Ultra DMA mode is not active, this signal gates I/O data from the device. (This pin supports three functions) HDMARDY#: In Ultra DMA mode when DMA Read is active, this signal is asserted by the Host to indicate that the Host is ready to receive Ultra DMA data-in bursts. The Host may negate HDMARDY# to pause an Ultra DMA transfer. HSTROBE: When DMA Write is active, this signal is the data-out strobe generated by the Host. Both the rising and falling edges of HSTROBE cause data to be latched by the device. The Host may stop generating HSTROBE edges to pause an Ultra DMA data-out burst. IOWR#: This is an I/O Write Strobe generated by the Host. When Ultra DMA mode is not active, this signal is used to clock I/O data into the device. (This pin supports two functions) STOP: When Ultra DMA mode protocol is active, the assertion of this signal causes the termination of the Ultra DMA burst 4 10/30/2012 S71382-F GLS85LD1001T / GLS85LD512 Industrial Grade PATA NANDriveTM Fact Sheet 01.000 October 2012 Table 3-1: Pin Assignments (2 of 2) Pin No. Pin Symbol Type 91-Ball I/O Type IORDY J4 O O1 IOCS16# J8 O O2 INTRQ PDIAG# J2 K9 O I/O O1 I1U/O1 DASP# D9 I/O I1U/O6 RESET# E4 I I2U WP#/PD# F6 I I3U Name and Functions IORDY: When in PIO mode, the device is not ready to respond to a data transfer request. This signal is negated to extend the Host transfer cycle from the assertion of IORD# or IOWR#. However, it is never negated by this controller. (This pin supports three functions) DDMARDY#: When Ultra DMA mode DMA Write is active, this signal is asserted by the device to indicate that the device is ready to receive Ultra DMA data-out bursts. The device may negate DDMARDY# to pause an Ultra DMA transfer. DSTROBE: When Ultra DMA mode DMA Read is active, this signal is the data-in strobe generated by the device. Both the rising and falling edges of DSTROBE cause data to be latched by the Host. The device may stop generating DSTROBE edges to pause an Ultra DMA data-in burst. This output signal is asserted low when the device is indicating a Word data transfer cycle. This signal is the active high Interrupt Request to the Host. The Pass Diagnostic signal in the Master/Slave handshake protocol. The Drive Active/Slave Present signal in the Master/Slave handshake protocol. This input pin is the active low hardware reset from the Host. The WP#/PD# pin can be used for either the Write Protect mode or Power-down mode, but only one mode is active at any time. The Write Protect or Power-down modes can be selected through the host command. The Write Protect mode is the factory default setting. Serial Communication Interface (SCI) SCIDOUT D8 O O4 SCIDIN SCICLK Miscellaneous D7 E7 I I I3U I3U VDD VDDQ G4, G6, G7, K4, K6, K7, J9 E9, K5, L5, M2 E2, M9 POR# J7 I VREG D2 A1, A2, A9, A10, B1, B9, B10, D3, D4, D5, D6, E5, E6, F5, G5, L4, L6, L7, M3, M4, M5, M6, M7, M8, N2, N3, N4, N5, N6, N7, N8, N9, R1, R2, R9, R10, T1, T2, T9, T10 O VSS DNU SCI data output. No external pull-up or pull-down resistor should connect to this signal. SCI data input SCI clock PWR Ground PWR PWR VDD (3.3V) VDDQ (5V/3.3V) for Host interface Power-on Reset (POR). Active low. Analog input for supply voltage detection External capacitor pin Analog Input These specifications are subject to change without notice. (c) 2012 Greenliant Systems Do not use. All these pins should not be connected. 5 10/30/2012 S71382-F GLS85LD1001T / GLS85LD512 Industrial Grade PATA NANDriveTM Fact Sheet 01.000 October 2012 4.0 Product Ordering Information GLS 85 LD XX XX 1 001T X XXXX - 60 - RI XX - XX - LBTE - XXXX Environmental Attribute 3) E = non-Pb Package Modifier T = 88 ball positions (nearest letter code to total ball count of 91) Package Type LB = LBGA Operation Temperature I = Industrial: -40C to +85C Write Cycles per Group R = 100M Host Access Time 60 = 60ns, UDMA Mode-4 Version Capacity 512 = 512 MByte 001 = 1 GByte MByte or GByte Designator 1 = GByte/ 0 = MByte Interface D = Parallel ATA/IDE Interface Voltage L = 3.3V Product Series 85 NANDrive 3) Environmental suffix "E" denotes nonPb solder. Greenliant non-Pb solder devices are "RoHS Compliant." Valid Combinations 4) PATA NANDrive Product GLS85LD0512-60-RI-LBTE/ GLS85LD1001T-60-RI-LBTE PATA NANDrive Evaluation Board (xxCN: xx-pin ATA Interface EVB, K: Kit) GLS85LD0512-60-RI-40CN-K, GLS85LD1001T-60-RI-40CN-K, GLS85LD0512-60-RI-44CN-K, GLS85LD1001T-60-RI-44CN-K 4) Valid product combinations are those that are in the mass production or will be in the mass production. Consult your Greenliant sales representative to confirm availability of the valid combinations and to determine availability of new product combinations. These specifications are subject to change without notice. (c) 2012 Greenliant Systems 6 10/30/2012 S71382-F GLS85LD1001T / GLS85LD512 Industrial Grade PATA NANDriveTM Fact Sheet 01.000 October 2012 4.1 Package Diagram 4.1.1 LBTE Package Figure 4-1: PATA NANDrive 91-Ball, Ball Grid Array (BGA) Greenliant Package Code: LBTE These specifications are subject to change without notice. (c) 2012 Greenliant Systems 7 10/30/2012 S71382-F GLS85LD1001T / GLS85LD512 Industrial Grade PATA NANDriveTM Fact Sheet 01.000 October 2012 4.2 Reference Documents Table 4-1: Reference Documents Title Revision 02.000 02.000 NANDrive SMART Specification WindowsPT2 User Guide 4.3 Date February 10, 2011 March 1, 2011 Revision History Table 4-2: Revision History Number 01.000 Description - Initial release (based on GLS85LD1001T/LD0512 PATA NANDrive Data Sheet Rev06.001, 10/30/2012) Date October 30, 2012 (c) 2012 Greenliant Systems. All rights reserved. Greenliant and the Greenliant logo are registered trademarks, and NANDrive is a trademark of Greenliant Systems. All other trademarks and registered trademarks are the property of their respective owners. Specifications are subject to change without notice. Memory sizes denote raw storage capacity; actual usable capacity may be less. Greenliant makes no warranty for the use of its products other than those expressly contained in the Greenliant Terms and Conditions of Sale. www.greenliant.com These specifications are subject to change without notice. (c) 2012 Greenliant Systems 8 10/30/2012 S71382-F Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Greenliant: GLS85LD0512-60-RI-44CN-K GLS85LD0512-60-RI-LBTE (Rev. AD0) GLS85LD0512-60-RI-40CN-K