E4408B BAS - KEYSIGHT TECHNOLOGIES

The ESA family of spectrum analyzers have proven

and guaranteed performance with the flexibility to

select the right level of functionality for your test

needs. Take advantage of the best overall perfor-

mance on a mid-performance spectrum analyzer.

Industry best typical performance

•Warm up time: 5 minutes

• Third order intermodulation distortion: +16 dBm

• Sensitivity: -166 dBm

• Amplitude accuracy: ± 0.4 dB

• Overall phase noise (all carrier frequenciesa):

• -101 dBc/Hz (10 kHz)

• -122 dBc/Hz (100 kHz)

• -136 dBc/Hz (1 MHz)

Agilent

ESA Series Spectrum Analyzers

Data Sheet

a. Add 20LogN for frequencies > 6.7 GHz, where N is the harmonic mixing mode.

Express analyzer configurations

• Basic Analyzer

Express Option BAS

• Standard Analyzer

Express Option STD

• Communications Test Analyzer

Express Option COM

Definitions and Conditions

The distinction between specifications and

characteristics is described as follows.

• Specifications describe the performance of

parameters covered by the product warranty.

(The temperature range is 0 °C to 55 °C, unless

otherwise noted.)

• Characteristics describe product performance that

is useful in the application of the product, but is

not covered by the product warranty.

• Typical performance describes additional product

performance information that is not covered by the

product warranty. It is performance beyond

specification that 80% of the units exhibit with

a 95% confidence level over the temperature range

20 to 30 °C. Typical performance does not include

measurement uncertainty.

• Nominal values indicate the expected performance,

or describe product performance that is useful in

the application of the product, but is not covered

by the product warranty.

• N/A (not applicable) - Not specified for this

configuration

The following conditions must be met for the analyzer

to meet its specifications.

• The analyzer is within the one year calibration

cycle.

• If Auto Align All is selected:

• After 2 hours of storage within the operating

temperature range.

• 5 minutes after the analyzer is turned on with

sweep times less than 4 seconds.

• If Auto Align Off is selected:

• When the analyzer is at a constant temperature,

within the operating temperature range, for a

minimum of 90 minutes.

• After the analyzer is turned on for a minimum

of 90 minutes and Align Now All has been run.

• When Align Now All is run:

• Every hour

• If the ambient temperature changes more

than 3 °C

• If the 10 MHz reference changes

• If Auto Align All but RF is selected:

• When the analyzer is at a constant temperature,

within the operating temperature range, for a

minimum of 90 minutes.

• After the analyzer is turned on for a minimum

of 90 minutes and Align Now RF has been run.

• When Align Now RF is run:

• Every hour

• If the ambient temperature changes more

than 3 °C

Table of Contents

Definitions and Conditions 2

Frequency Specifications 3

Amplitude Specifications 7

Tracking Generator Specifications 12

Quasi-Peak Detector Specifications 13

General Specifications 14

Option Ordering 16

a. 30 Hz characteristic.

b. N = LO harmonic mixing mode.

E4411B

Frequency range E4403B E4408B

BAS configuration 9 kHz - 1.5 GHz 9 kHz - 3 GHz 9 kHz - 26.5 GHz

Custom configuration N/A N/A

(75 Ω input Option 1DP)

1 MHz - 1.5 GHz

E4402B E4404B E4405B E4407B

STD or COM configuration 9 kHz - 3 GHz 9 kHz – 6.7 GHz 9 kHz – 13.2 GHz 9 kHz - 26.5 GHz

Custom configuration

Low frequency extension Option UKB

100 Hza - 3 GHz 100Hza - 6.7 GHz 100Hza - 13.2 GHz

100Hza - 26.5 GHz

External mixing

Option AYZ

Add 18 GHz - 325 GHz

Frequency range

Frequency range 100 Hz - 3 GHz 2.85 - 6.7 GHz 6.2 - 13.2 GHz 12.8 – 19.2 GHz 18.7 – 26.5 GHz

Band 01234

Harmonic (Nb)

mixing mode 1- 1- 2- 4- 4-

Frequency Specifications

Standard analyzer

Communications test

analyzer or ESA with

Option 1D5

±2 x 10 –6

/year

±1 x 10 –7

/year

(Opt. 1D5)

±5 x 10 –6

/year

±1 x 10 –8

/year

(Opt. 1D5)

±5 x 10 –7

/year

±1 x 10 –8

/year

(Opt. 1D5)

[0.5 % + 1/ (sweep

points –1) ] x span

[0.5 % + 1/ (sweep

points –1) ] x span

10 MHz 1 - 30 MHz

Logarithmic scale N/A

Range = 0 Hz (zero span), 100 Hz to maximum frequency range of the analyzer

Accuracy

Linear scale 1% of span ±[0.5% x span + 2 x span/(sweep points – 1)]

2% of span, nominal

Marker frequency counterd

Accuracy = ±(marker frequency x frequency reference error + counter resolution)

Counter resolution = selectable from 1 Hz to 100 kHz

Frequency span

Span coefficient (SP)c0.75 % x span

External reference 10 MHz

Temperature stability ±5 x 10 –6

/year ±1 x 10–8/yearb

Settability ±5 x 10 –7

/year ±1 x 10 –8

/year

Frequency readout accuracy (start, stop, center, marker)

= ±(frequency indication x frequency reference error + SPc +15% of RBW + 10 Hz + 1 Hz x Na)

Aging rate ±2 x 10 –6

/year ±1 x 10 –7

/year

Basic analyzer

Frequency reference

Frequency reference error = ± [(aging rate x time since last adjustment )+ settability + temperature stability]

a. N = LO harmonic mixing mode.

b. 20 to 30 °C.

c. +5% of span + . Sweep points fixed at 401 for basic analyzer.

d. Not available in RBW < 1 kHz (Option 1DR).

Frequency Specifications

span

sweep pts. – 1

Standard analyzer Communications test analyzer

or ESA with Option AYX or ESA with Option B7D/B7E

Span = 0 Hz 4 ms – 4000 s 50 nsa – 4000 s 25 nsa - 4000 s

Span ≥ 100 Hz 4 ms – 4000 s

RF burst (B7E)

Span = 0 Hz 401

Span ≥ 100 Hz 401

Delayed trigger range 1 us to 400 s

Sweep (trace) points

Range

2 - 8192

101 - 8192

Accuracy (Span = 0 Hz) ± 1%

Trigger typeb

Free Run, Single, Line, Video, Offset, Delayed, External

Gate (1D6)

Basic analyzer

Sweep time and trigger

Range

1 ms– 4000 s

N/A

Communications test analyzer

or ESA with Option 1DR and 1D5

(-3 dB) 1 kHz – 5 MHzd 1 kHz – 5 MHzd 1 Hz to 5 MHzd

(-6 dB EMI) 9 KHz, 120 kHz 9 KHz, 120 kHz 200 Hz, 9 kHz,120 kHz

With 1DRc (-3dB) Add 100 Hz, 300 Hz Add 10 Hz - 300 Hz

(-6 dB EMI) Add 200 Hz Add 200 Hz

With 1DR and 1D5eN/A Add 1 Hz and 3 Hz Included

1 Hz to 300 Hz

1 kHz to 3 MHz

5 MHz

100 Hz to 300 Hz

1 kHz to 5 MHz

Range

with 1DR

< 15:1 synchronously tuned four poles, approximately Gaussian

Video bandwidths (1-3-10 sequence)

30 Hz to 3 MHz

Adds 1, 3, 10 Hz for RBWs less than 1 kHz

± 15%

± 30%

Selectivity (60 dB/3 dB bandwidth ratio)

< 5:1 digital, approximately Gaussian

Range

Included

Accuracy

± 10%

Basic analyzer Standard analyzer

Resolution bandwidths (1-3-10 sequence)

a. RBW ≥1 kHz, 2 sweep points.

b. TV trigger available with option B7B in custom configuration for ESA-E.

c. Only available for spans < 5MHz.

d. For resolution bandwidths < 1 kHz or > 3 MHz, not compatible with the rms detector.

e. Firmware revision A.08.00 and later.

Frequency Specifications

ESA-E

E4411B E4403B/08B with Option 120a

Offset from

CW signal

≥ 1 kHz

≥ 10 kHz -93, -95 dBc/Hz -98, -101 dBc/Hz (Option 1D5)

-100, -105 dBc/Hz -104, -107 dBc/Hz

-106, -112 dBc/Hz -110, -113 dBc/Hz

-118, -122 dBc/Hz -118, -122 dBc/Hz

-125, -127 dBc/Hz

-127, -129 dBc/Hz

-131, -136 dBc/Hz

-133, -136 dBc/Hz

-135, -139 dBc/Hz

-137, -141 dBc/Hz

-100, -102 dBc/Hz

-104, -106 dBc/Hz

-113, -116 dBc/Hz

-90, -94 dBc/Hz

≥ 20 kHz

≥ 30 kHz

≥ 100 kHz

≥ 1 MHz

≥ 5 MHz

≥ 10 MHz

Residual FM (peak-to-peak)

Stability

Noise sidebands offset from CW signal with 1 kHz RBW, 30 Hz VBW and sample detector

Spec and typical dBc/Hz applies to all frequencies ≤ 6.7 GHz

b, c

Italics indicate typical performance

-78 dBc/Hz (Option 1D5 and 1DR)

Basic analyzer Standard and communications test analyzer

E4402B/04B/05B/07B

N/A

N/A N/A

N/A

Option 1D5 only

100 ms

Option 1DR only

20 ms

Option 1DR & 1D5

20 ms

≥ 30 kHz offset from

carrier CW signal

System related sidebands

≤ -65 dBc + 20logNc

≤ 10 Hz x Nc

≤ 2 Hz peak-to-peak x Nc

≤ 150 Hz x Nc (100 ms)

≤ 10 Hz x Nc(20 ms), Option 1DR

≤ 2 Hz peak-to-peak x Nc, (20 ms), Option 1DR & 1D5

≤ 100 Hz x Nc

1 kHz RBW,

1 kHz VBW

(measurement

time)

≤ 150 Hz x Nc (100 ms)

≤ 30 Hz x Nc(20 ms), Option 1DR

Figure 1. Typical ESA-E Series performance at 1 GHz a. Enhanced wide offset phase noise and ACPR dynamic range.

b. Add 20log(N) for frequencies > 6.7 GHz.

c. N=LO Harmonic mixing number.

d. Option 1DR is required for phase noise measurements at frequency offsets of 10 kHz

and less. Performance at the 10 kHz offset without Option 1DR is –90/–94 dBc/Hz.

Frequency Specifications

Typical performance

@ 1 GHz (Standard)

Typical performance

@ 1 GHz (Option 120)

Spec (Standard)

Spec (Option 120)

Spec (Option 1DR)

E4411B E4403B/08B E4402B E4404B/05B E4407B

≥ 15 dB

+30 dBm +30 dBm (1 W)

(1 W) +50 dBm (100 W)

0 Vdc

(Option UKB)

100 Vdc

+75 dBmV (0.4 W) Option 1DP 50 Vdc (Opt. UKB)

0 dBm to 1.5 GHz

46.75 dBmV (1DP)

0 dBm

-3 dBm

-5 dBm

Total power at input mixerb

50 MHz to 6.7 GHz

6.7 GHz to 13.2 GHz

13.2 GHz to 26.5 GHz

50 Vdc 50 Vdc (Opt. UKB)

1 dB gain compression Two tone

Peak pulse powera+50 dBm (100 W)

voltage

DC coupled N/A N/A 0 Vdc 0 Vdc

AC coupled 100 Vdc

≥ 5 dB average continuous power; ≥ 30 dB peak pulse power

Input attenuator setting

Average continuous power +30 dBm (1 W)

0 – 75 dB 0 – 75 dB 0 – 65 dB

Maximum safe input level

Input attenuator range

(5 dB step) 0 – 60 dB 0 – 65 dB

Amplitude range

Measurement range Displayed average noise level (DANL) to maximum safe input level

a. < 10 µs pulse width, < 1% duty cycle.

b. Mixer power level (dBm) = input power (dBm) minus input attenuation (dB).

Amplitude Specifications

E4411B E4403B E4408B E4402B E4404/05B/07B E4402B E4404/05/7B

Frequency

1 MHz - 10 MHz

10 MHz - 500 MHz

500 MHz - 1 GHz

1 GHz - 1.5 GHz

1.5 GHz - 2 GHz

2 GHz - 3 GHz -133, typ -140

3 GHz - 6 GHz

6 GHz - 12 GHz -130, typ -137 typ -147

12 GHz - 22 GHz

N/A

N/A N/A N/A

-126, typ -134 typ -144

22 GHz - 26.5 GHz -125, typ -132 typ -142

1 MHz - 10 MHz typ-152 typ -155 typ -162 typ -165

10 MHz - 1 GHz -152, typ -156 -151, typ -157 typ -166 typ -167

1 GHz - 2 GHz -152, typ -156 -151, typ -155 typ -166 typ -165

2 GHz - 3 GHz -151, typ-154 -149, typ -152 typ -164 typ -162

Displayed average noise level (dBm) with RF preamplifierb

-131, typ -138 typ -148

-135, typ -140 -135, typ -140 typ -150

typ-137, -139atyp-146, -149 atyp-147, -149 a

-136, typ -140 -135, typ -139

typ-150

typ -149

-123, typ -129

-123, typ -130

-124, typ -129

-127, typ -131

-125, typ -130 -125, typ -130

-124, typ -130

-122 typ -130

-121, typ -128

-120, typ -128

-118, typ -127

-115, typ -124

-109, typ -122

typ -126 typ -129 typ -139

Displayed average noise level (dBm) (input terminated, 0 dB attenuation, sample detector) spec, typical

Conditions 100 Hz RBW; 1 Hz VBW (Option 1DR); 10 Hz RBW/1 Hz VBW (Option 1DR) 1 Hz RBW/VBW

(ESA with 1DR and 1D5)

Basic analyzer Standard analyzer Communications test analyzer

or ESA with 1DR and 1D5

a. Custom path only, Option 120, typical.

b. 20 to 30° C. For 0 to 55 °C range, see specifications guide.

Amplitude Specifications

Standard analyzer Communications test analyzer

or ESA with Option AYX or ESA with Option B7D/B7E

Display range

Log scale

RBW ≥ 1 kHz

RBW ≤ 300 Hz

Linear scale

Scale units dBm, dBmV, dBµV,

dBµA, A, V, and W

dBm, dBmV, dBµV, dBµA, A, V, W and Hz (Option BAA or AYQ)

Trace detectors

Trace functions

Log scale

0 to – 85 dB 0.04

0 to –120 dB (1DR)

Linear scale 0.01% of reference level

Range

Resolution

Log scale

Linear scale

Accuracyc

-10 dBm to > -60 dBm

-60 dBm to > -85 dBm

-85 dBm to > -90 dBm

Linear to log switching

1 Hz, 3 Hz RBW

10 Hz, 30 Hz RBW

100 Hz, 300 Hz RBW

N/A

± 0.3 dB (1DR, 1D5) ± 0.3 dB (1D5)

1 kHz to 3 MHz RBW

± 0.3 dB (1DR)

± 0.3 dB

Resolution bandwidth switching uncertainty (referenced to 1 kHz at reference level)

± 0.5 dB

± 0.7 dB

Display scale switching uncertainty (referenced to 1 kHz RBW at reference level)

± 0.15 dB at reference level

±0.1 dB

± 0.12% of reference level

For reference level (dBm) – input attenuator setting (dB) + preamp gain (dB)

± 0.3 dB

Marker readout resolution

Reference level

–149.9 dBm to maximum mixer level + attenuator setting

Peak, negative peak, sample, rmsb, video averaging

Clear/write, max. hold, min. hold, view, blank, operations, normalize

Calibrated 0 to -85 dB from reference level

Calibrated 0 to -120 dBa from reference level

10 divisions

Basic analyzer

Display

0.1, 0.2, 0.5 dB/division and 1 to 20 dB/division in 1 dB steps (10 display divisions)

± 0.3 dB (1DR) ± 0.3 dB

± 0.3 dB

± 0.6 dB

5 MHz RBW

a. 0 to -70 dB range when span = 0 Hz, or when IF gain fixed.

b. Not available for RBW < 1 kHz or > 3 MHz.

c. 50 Ω, accuracy (at a fixed frequency, a fixed attenuator, and referenced to -35 dBm

(-10 dBm, Preamp On (Option 1DS))).

Amplitude Specifications

Basic analyzer Standard, communications test analyzer or

custom configuration

Attenuator setting

0 dB to 5 dB

10 dB

15 dB

20 dB to 60 dB

Absolutea/typical/relativeb

100 Hz to 9 kHzc

± 0.46 dB/± 0.14 dB/± 0.5 dB

± 0.5 dB/NA/± 0.5 dBa (Option UKB)

3 GHz to 6.7 GHz ± 1.5 dB/NA/± 1.3 dB ± 1.5 dB/± 0.38 dB/± 1.3 dB

6.7 GHz to 13.2 GHz ± 2 dB/± 0.68 dB/± 1.8 dB

13.2 GHz to 26.5 GHz ± 2 dB/± 0.86 dB/± 1.8 dB

At reference settingsd± 0.4 dB ± 0.34 dB, ± 0.13 dB typical

Preamp on ± 0.37 dB, ± 0.14 dB typical

Overall amplitude accuracye± (0.6dB + absolute frequency response) ± (0.54 dB + absolute frequency response)

(95% confidence)f± 0.4 dB (95%)

Log max cumulative

dB below reference level

RBW ≥ 1 kHz

0 dB reference

> 0 to 10 dB

> 10 to 20 dB

> 20 to 30 dB

> 30 to 40 dB

> 40 to 50 dB

> 50 to 60 dB

> 60 to 70 dB

> 70 to 80 dB

> 80 to 85 dB ±1.15 dB, typ ±0.79 dB

±0.8 dB, typ ±0.46 dB

±0.8 dB, typ ±0.39 dB

±0.7 dB, typ ±0.35 dB

±0.6 dB, typ ±0.23 dB

±0.5 dB, typ ±0.1 dB

±0.4 dB, typ ±0.09 dB

±0.3 dB, typ ±0.08 dB

RBW ≤ 300 Hz (Option 1DR)

span > 0 Hz, auto range on

0 to 98 dBg

> 98 to 120 dB

Log incremental accuracy

dB below reference level

0 to 80 dBg

Linear accuracy

± (0.3dB + 0.01 x dB

from reference level)

± 2.0 dB from reference level, characteristic

± 0.4 dB / 4 dB

Display scale fidelity

± (0.3dB + 0.01 x dB

from reference level

0 dB

± 2% of reference level

9 kHz to 3 GHz ± 0.5 dB/NA/± 0.5 dB

± 2 dB/NA/± 1.8 dB

Absolute amplitude accuracy

± (0.1 dB + 0.01 x attenuator setting)

Frequency response (10 dB input attenuation)

± 0.5 dB/NA/± 0.5 dB

Input attenuator switching uncertainty (at 50 MHz)

± 0.3 dB

Reference

N/A

a. Frequency response values are referenced to the amplitude at 50 MHz

(20 to 30 °C).

b. Referenced to midpoint between highest and lowest frequency response

deviations (20 to 30 °C).

c. Custom path ESA-E only Option UKB, typical.

d. Settings are: reference level -25 dBm; (75 Ωreference level +28.75 dBmV);

input attenuation 10 dB; center frequency 50 MHz; RBW 1 kHz; VBW 1 kHz;

amplitude scale linear or log; span 2 kHz; frequency scale linear; sweep time

coupled, sample detector, signal at reference level.

e. For reference level 0 to -50 dBm; input attenuation 10 dB; RBW 1 kHz;

VBW 1 kHz; amplitude scale log, log range 0 to -50 dB from reference level;

frequency scale linear; sweep time coupled; signal input 0 to -50 dBm;

span ≤20 kHz. (20 to 30 °C).

f. Input frequency < 3GHz; -50 dBm ≤input power ≤0 dBm; -50 dBm ≤reference

level ≤0 dBm; -20 dB ≤input power - ref level ≤0 dB; input attenuation = 10 dB;

10 Hz ≤RBW ≤1 MHz; (20 to 30 °C). Computed from the observation of a

statistically significant number of instruments. Observations of the 50 MHz

amplitude accuracy, a component of the computation of this number are

performed immediately after invoking RF and IF alignments to minimize the

effects of alignment drifts.

g. 0 to 30 dB for RBW = 200 Hz.

Amplitude Specifications

Standard, communications test analyzer or

customer configuration E4402B/04B/05B/07B

10 MHz to 100 MHz

< -75 dBc, + 7.5 dBm TOI

N/A

< -75 dBc, + 35 dBm SHI (E4411B)

< -60 dBc, + 30 dBm SHI

< -70 dBc, + 40 dBm SHI

< -80 dBc, + 70 dBm SHI

≤ -95 dBc, + 85 dBm TOI

100 MHz to 3 GHz < -85 dBc, +12.5 dBm; typ +16 dBm TOI

+7 dBm, characteristic

< -75 dBc, +7.5 dBm; typ +12 dBm TOI

< -75 dBc, +7.5 dBm; typ +11 dBm TOI

< -82 dBc, +11 dBm; typ +18 dBm TOI

3.0 GHz to 6.7 GHz

6.7 GHz to 13.2 GHz

13.2 GHz to 26.5 GHz

Second harmonic distortion

2 MHz to 750 MHz

- 40 dBm tone at input mixera

10 MHz to 500 MHz < -65 dBc, + 35 dBm SHI

< -75 dBc, + 45 dBm SHI

< -85 dBc, + 75 dBm SHI

< -100 dBc, + 90 dBm SHI

- 30 dBm tone at input mixera

500 MHz to 1.5 GHz

- 30 dBm tone at input mixera

1.5 GHz to 2.0 GHz

- 10 dBm tone at input mixera

> 2 GHz

- 10 dBm tone at input mixera

WCDMA ACPR dynamic rangeb

Offset frequency

5 MHz

-60 dBc, -65 dBc (Opt 120), -66.5 dBc

noise correction on

-64.5 dBc, -65.5 dBc(Opt 120), -67 dBc

noise correction on

Other input related spurious

Inband > 30 kHz offset

Out of band responses < -80 dBc -10 dBm tone at input mixera

10 MHz

< -65 dBc for -20 dBm tone at input mixera

Input terminated and 0 dB attenuation

Basic analyzer

E4411B/03B/08B

Spurious responses

Third order intermodulation distortion For two -30 dBm signals at input mixera and > 50 kHz separation

Residual responses ( Input terminated and 0 dB attenuation)

50 Ω RF input impedance

150 kHz to 1.5 GHz/6.7 GHzc< -90 dBm

75 Ω RF input impedance (Option 1DP only

available on ESA-L Custom Configuration for the E4411B)

1 MHz to 1.5 GHz < -36 dBmV

Figure 2. Specified dynamic range for E4407B spectrum analyzer

a. Mixer power level (dBm) = input power (dBm) - input attenuation (dB).

b. Characteristic. Measured by selecting “Measure, ACP”, 20 to 30 °C, 3GPP

(3.1 Dec 1999) W-CDMA signal with 1 DPCH, channel power -9 dBm/3.84 MHz,

integration bandwidth 3.84 MHz, carrier frequency 2 GHz, reference level

-16 dBm, input attenuation 0 dB, RBW 30 kHz. Noise correction can be turned on

by selecting Meas Setup, More, Noise Corr On.

c. Up to 1.5 GHz for models E4402B/03B/11B. Up to 6.7 GHz for models

E4404B/05B/07B/08B.

Amplitude Specifications

Tracking generator Specifications (Options 1DN and 1DQ)

Frequency range

E4411B

Option 1DN, (50 Ω) 9 kHz to 1.5 GHz

Option 1DQ, (75 Ω) 1 MHz to 1.5 GHz

E4402B/03B/04B/05B/07B/08B

Option 1DN, (50 Ω) 9 kHz to 3.0 GHz

RBW range 1 kHz to 5 MHz

Output power level range

E4411B

Option 1DN 0 to –70 dBm

Option 1DQ +42.75 to –27.25 dBmV

E4402B/03B/04B/05B/07B/08B

Option 1DN –2 to –66 dBm

Output vernier range

E4411B 10 dB

E4402B/03B/04B/05B/07B/08B 8 dB

Output attenuator range

E4411B 0 to 60 dB, 10 dB steps

E4402B/03B/04B/05B/07B/08B 0 to 56 dB, 8 dB steps

Output flatness

E4411B

Option 1DN, (50 W)

9 kHz to 10 MHz ±2.0 dB

10 MHz to 1.5 GHz ±1.5 dB

Option 1DQ, (75 W)

1 MHz to 10 MHz ±2.5 dB

10 MHz to 1.5 GHz ±2.0 dB

E4402B/03B/04B/05B/07B/08B

9 kHz to 10 MHz ±3.0 dB

10 MHz to 3.0 GHz ±2.0 dB

Effective source match (characteristic)

E4411B < 2.5:1

E4402B/03B/04B/05B/07B/08B < 2.0:1 (0 dB attenuator)

< 1.5:1 (8 dB attenuator)

Spurious output

Harmonic spurs

E4411B

(0 dBm output)

9 kHz to 20 MHz < –20 dBc

20 MHz to 1.5 GHz < –25 dBc

E4402B/03B/04B/05B/07B/08B

(–1 dBm output)

20 kHz to 3 GHz < –25 dBc

Non-Harmonic spurs

E4411B < –35 dBc

E4402B/03B/04B/05B/07B/08B

9 kHz to 2 GHz < –27 dBc

2 GHz to 3 GHz < –23 dBc

Dynamic range

Maximum output power – displayed average noise level

Output power sweep range

E4411B

Option 1DN (–15 dBm to 0 dBm) – (source attenuator setting)

Option 1DQ (+27.75 dBmV to +42.75 dBmV) –(source attenuator setting)

E4402B/03B/04B/05B/07B/08B

Option 1DN (–10 dBm to –2 dBm) – (source attenuator setting)

Tracking Generator Specifications

Add a quasi-peak detector, Option AYQ, to the ESA

custom analyzer configuration. Option AYQ also

includes FM demodulation capability. The quasi-peak

detector displays the quasi-peak amplitude of a pulse

radio frequency on continuous wave signals.

Amplitude response conforms with Publication 16

of Comite International Special des Perturbations

Radioelectrique (CISPR) Section 1, Clause 2, as

indicated in the relative quasi-peak response table.

Pulse repetition 120 kHz EMI BW 9 kHz EMI BW 200 Hz EMI BW

frequency (Hz) .03 to 1 GHz 0.150 to 30 MHz 9 kHz to 150 kHz

1000 +8.0 ±1.0 +4.5 ±1.0 --------------

100 0 dB referencea 0 dB referencea +4.0 ±1.0

60 -------------- -------------- +3.0 ±1.0

25 -------------- -------------- 0 dB referencea

20 -9.0 ±1.0 -6.5 ±1.0 --------------

10 -14 ±1.5 -10.0 ±1.5 -4.0 ±1.0

5 -------------- ------------- -7.5 ±1.5

2 -26 ±2.0 -20.5 ±2.0 -13.0 ±2.0

1 -------------- -22.5 ±2.0 -17.0 ±2.0

Isolated pulse -------------- -23.5 ±2.0 -19.0 ±2.0

ESA Custom configuration with Option AYQ (requires Option 1DR)

Relative quasi-peak response to a CISPR pulse (dB)

a. Reference pulse amplitude accuracy relative a 66 µV CW signal < 1.5 dB as specified in

CISPR Pub 16 CISPR reference pulse: 0.44 µVs for 30 MHz to 1 GHz, 0.316 µVs for 150 kHz

to 30 MHz, 13.5 µVs for 9 kHz to 150 kHz

Quasi-Peak Detector Specifications

E4411B E4403B E4408B E4404/05/07B

Temperature range

Operating

Storage

Disk drive

Audible noise

sound pressure at 25 °C

Military specifications

Power requirements

AC operation on (line |)

Standby (line )

DC operation

Data storage (nominal)

Internal

External

Memory usage (nominal)

State

State plus 401- point trace

Weight (without options)

13.2 kg 15.5 kg 17.1 kg 17.1 kg

29.1 lb 34.2 lb 37.7 lb 37.7 lb

Measurement speed

Local measurement rate ≥ 35/sec ≥ 30/sec ≥ 28/sec ≥ 40/sec

Remote measurement and

GPIB transfer

RF center freq tuning time ≤ 90 ms ≤ 90 ms ≤ 90 ms ≤ 75 ms≤ 75 ms

≥ 45/sec

≥ 30/sec ≥ 30/sec ≥ 30/sec ≥ 45/sec ≥ 40/sec

16 kB

20 kB

Kilograms

15.5 kg

34.2 lb

200 traces or states/8.0 MB

3.5” 1.44 MB, MS-DOS

Power consumption < 300W

Power consumption < 5W

12 to 20 Vdc, < 200 W power consumption

Type tested to the environmental specifications of MIL-PRF-28800F class 3

90 to 132 V rms, 47 to 440 Hz

195 to 250 V rms, 47 to 66 Hz

EMI compatibility Conducted and radiated interference is in compliance with CISPR Pub. 11/1990 Group 1 Class A

Conducted and radiated interference is in compliance with CISPR Pub. 11/1990 Group 1 Class Ba (Option 060)

< 40 dBa pressure and < 4.6 bels power (ISODP7779)

0 °C to +55 °C

-40 °C to +75 °C

10 °C to +40 °C

Basic analyzer Standard, communications test analyzer

or custom configuration

E4402B

Display resolutiond640 x 480

a. Meeting class A performance during DC operation.

b. For serial numbers < US414400 or MY41440000, 1MB without Option B72,

8 Mb with Option B72.

c. 401 sweep points. The size of a state will increase depending on the installed

application(s).

General Specifications

d. The LCD display is manufactured using high precision technology. However, there

may be up to six bright points (white, blue, red or green in color) that constantly

appear on the LCD screen. These points are normal in the manufacturing process

and do not affect the measurement integrity of the product in any way.

Inputs/outputs

Front panel

Input 50 Ω type N (f); 75 Ω BNC (f) (Option 1DP); 50

Ω

APC 3.5 (m) (Option BAB)

RF out 50 Ω type N (f); 75 Ω BNC (f) (Option 1DQ)

Probe power + 15 Vdc, -12.6 Vdc at 150 mA maximum (characteristic)

External keyboard 6-pin mini-DIN, PC keyboards (for entering screen titles and file names)

Headphone Front panel knob controls volume

Power output 0.2 W into 4 Ω (characteristic)

AMPT REF out 50 Ω BNC (f) (nominal)

IF INPUT (Option AYZ) 50 Ω SMA (f) (nominal)

LO OUTPUT (Option AYZ) 50 Ω SMA (f) (nominal)

Rear panel

10 MHz REF OUT 50 Ω BNC (f), > 0 dBm (characteristic)

10 MHz REF IN 50 Ω BNC (f), -15 to +10 dBm (characteristic)

GATE TRIG/EXT TRIG IN BNC (f), 5 V TTL

GATE /HI SWP OUT BNC (f), 5 V TTL

VGA OUTPUT VGA compatible monitor, 15-pin mini D-SUB, (31.5 kHz horizontal,

60 Hz vertical sync rates, non-interlaced analog RGB 640 x 480)

IF, sweep and video ports (Option A4J or AYX)

AUX IF OUT BNC (f), 21.4 MHz, nominal -10 to -70 dBm (uncorrected)

AUX VIDEO OUT BNC (f), 0 to 1V, characteristic (uncorrected)

HI SWP IN BNC (f), low stops sweep, (5 V TTL)

HI SWP OUT BNC (f), (5 V TTL)

SWP OUT BNC (f), 0 to +10 V ramp

GPIB interface (Option A4H) IEEE-488 bus connector

Serial interface (Option 1AX) RS-232, 9-pin D-SUB (m)

Parallel interface

(Option A4H or 1AX) 25-pin D-SUB (f) printer port only

Dimensions and weight for the ESA family of analyzers.

Width to outside of instrument handle 416 mm (16.4 in.)

Width to outside of the shipping cover 373 mm (14.7 in.)

Overall height 222 mm (8.75 in.)

Depth from front frame to rear frame 409 mm (16.1 in.)

Depth with instrument handle rotated horizontal 516 mm (20.3 in.)

E4401B/11B

Instrument Weight 13.2 kg (29.1 lbs.)

Shipping Weight 25.1 kg (55.4 lbs.)

E4402B/E4403B

Instrument Weight 15.5 kg (34.2 lbs.)

Shipping Weight 27.4 kg (60.4 lbs.)

E4404B/E4405B

Instrument Weight 17.1 kg (37.7 lbs.)

Shipping Weight 31.9 kg (70.3 lbs.)

E4407B/08B

Instrument Weight 17.1 kg (37.7 lbs.)

Shipping Weight 31.9 kg (70.3 lbs.)

I/O connectivity software IO Libraries Suite (www. agilent.com/find/iosuite/data-sheet)

General Specifications (continued)

Option Ordering

For information on ordering options, please refer to

the ESA/EMC Spectrum Analyzer Configuration

Guide, literature number 5968-3412E.

More Information

For the latest information on the Agilent ESA-E

Series see our Web page at:

www.agilent.com/find/esa

www.agilent.com

Agilent Technologies’ Test and Measurement Support, Services, and Assistance

Agilent Technologies aims to maximize the value you receive, while minimizing your

risk and problems. We strive to ensure that you get the test and measurement

capabilities you paid for and obtain the support you need. Our extensive support

resources and services can help you choose the right Agilent products for your

applications and apply them successfully. Every instrument and system we sell

has a global warranty. Two concepts underlie Agilent’s overall support policy: “Our

Promise” and “Your Advantage.”

Our Promise

Our Promise means your Agilent test and measurement equipment will meet

its advertised performance and functionality. When you are choosing new

equipment, we will help you with product information, including realistic perfor-

mance specifications and practical recommendations from experienced test engi-

neers. When you receive your new Agilent equipment, we can help verify that it

works properly and help with initial product operation.

Your Advantage

Your Advantage means that Agilent offers a wide range of additional expert test

and measurement services, which you can purchase according to your unique tech-

nical and business needs. Solve problems efficiently and gain a competitive edge

by contracting with us for calibration, extra-cost upgrades, out-of-warranty repairs,

and onsite education and training, as well as design, system integration, project

management, and other professional engineering services. Experienced Agilent

engineers and technicians worldwide can help you maximize your productivity, opti-

mize the return on investment of your Agilent instruments and systems, and obtain

dependable measurement accuracy for the life of those products.

www.agilent.com/find/open

Agilent Open simplifies the process of connecting and programming test systems

to help engineers design, validate and manufacture electronic products. Agilent

offers open connectivity for a broad range of system-ready instruments, open

industry software, PC-standard I/O and global support, which are combined to

more easily integrate test system development.

United States: Korea:

(tel) 800 829 4444 (tel) (080) 769 0800

(fax) 800 829 4433 (fax) (080)769 0900

Canada: Latin America:

(tel) 877 894 4414 (tel) (305) 269 7500

(fax) 800 746 4866 Taiwan:

China: (tel) 0800 047 866

(tel) 800 810 0189 (fax) 0800 286 331

(fax) 800 820 2816 Other Asia Pacific

Europe: Countries:

(tel) 31 20 547 2111 (tel) (65) 6375 8100

Japan: (fax) (65) 6755 0042

(tel) (81) 426 56 7832 Email: tm_ap@agilent.com

(fax) (81) 426 56 7840 Contacts revised: 05/27/05

For more information on Agilent Technologies’ products, applications or services,

please contact your local Agilent office. The complete list is available at:

www.agilent.com/find/contactus

Product specifications and descriptions in this document subject to change

without notice.

Printed in USA, October 5, 2005

5968-3386E

www.agilent.com/find/emailupdates

Get the latest information on the products and applications you select.

Agilent Email Updates

www.agilent.com/find/agilentdirect

Quickly choose and use your test equipment solutions with confidence.

Agilent Direct

Agilent Open