K3MA-F-A2 100-240VAC - Omron Automation and Safety

CSM_K3MA-F_DS_E_12_1

Frequency/Rate Meter

K3MA-F

Highly Visible LCD Display with 2-color (Red and

Green) LEDs

• Contact, NPN, PNP, or voltage pulse input.

• Front-panel key operation for easy setting.

• Average processing function suppresses flicker.

• Includes scaling, auto-zero time, startup compensation time functions.

• Easy confirmation of max/min display.

• Short 80-mm depth (measured from edge of face plate).

• Finger protective cover (standard equipment) guards against electric

shock.

• Water- and dust-proof NEMA4X (IP66 equivalent) front panel.

• Recognized to U.S. and Canadian requirements under the Compo-

nent Recognition Program of UL.

•CE marking.

• Built-in external power supply (12 VDC, 40 mA).

Model Number Structure

■Model Number Legend

1. Input Type

F: Rotary pulse

2. Output Type

None: No output

A2: 2 relay contact outputs (SPST-NO)

3. Supply Voltage

100-240VAC: 100 to 240 VAC

24VAC/VDC: 24 VAC/VDC

Ordering Information

■List of Models

Refer to Safety Precautions for All Digital Panel

Meters.

For the most recent information on models that have been certified for

safety standards, refer to your OMRON website.

1 2 3

K3MA-F-@

Input type Supply voltage Output Model

Rotary pulse 100 to 240 VAC None K3MA-F 100-240VAC

2 relay contact outputs (SPST-NO) K3MA-F-A2 100-240VAC

24 VAC/VDC None K3MA-F 24VAC/VDC

2 relay contact outputs (SPST-NO) K3MA-F-A2 24VAC/VDC

K3MA-F

■Accessories (Order Separately)

Specifications

■Ratings

Name Shape Model

Splash-proof Soft Cover K32-49SC

Hard Cover K32-49HC

Watertight Cover Y92A-49N

Rubber Packing K32-P1

Model K3MA-F 100-240VDC, K3MA-F-A2 100-240VAC K3MA-F 24VAC/VDC, K3MA-F-A2 24VAC/VDC

Supply voltage 100 to 240 VAC 24 VAC/VDC

Operating voltage range 85% to 110% of the rated supply voltage

Power consumption

(under maximum load)

6 VA max. 4.5 VA max. (24 VAC)

4.5 W max. (24 VDC)

External power supply 12 VDC, 40 mA

Insulation resistance 20 MΩ min. (at 500 VDC) between external terminal and case.

Insulation provided between inputs, outputs, and power supply.

Dielectric strength 2,000 VAC for 1 min between external terminal and case.

Insulation provided between inputs, outputs, and power supply.

Noise immunity ±1,500 V on power supply terminals in normal or com-

mon mode.

±1 μs, or 100 ns for square-wave noise with 1 ns.

±480 V on power supply terminals in normal mode.

±1,500 V in common mode.

±1 μs, or 100 ns for square-wave noise with 1 ns.

Vibration resistance Vibration: 10 to 55 Hz, Acceleration: 50 m/s2

5 min each in X, Y, and Z directions for 10 sweeps.

Shock resistance 150 m/s2 (100 m/s2 for relay contact outputs) 3 times each on 3 axes, 6 directions.

Ambient temperature Operating: −10°C to 55°C (with no condensation or icing)

Storage: −25°C to 65°C (with no condensation or icing)

Approved safety standards UL61010-1, CSA C22.2 No.61010-1-04, conforms to EN61010-1 (Pollution degree 2/overvoltage category II)

Conforms to VDE0106/P100 (finger protection)

EMC (EMI) EN61326+A1 Industry

Emission Enclosure: CISPR 11 Group 1 class A: CISRP16-1/-2

Emission AC Mains: CISPR 11 Group 1 class A: CISRP16-1/-2

(EMS) EN61326+A1 Industry

Immunity ESD: EN61000-4-2: 4 kV contact discharge

8 kV air discharge

Immunity RF-interference: EN61000-4-3: 10 V/m (amplitude-modulated, 80 MHz to 1 GHz)

Electrical Fast Transient Noise: EN61000-4-4: 2 kV (power line)

Immunity Burst Noise: 1 kV line to line (I/O signal line)

Immunity Surge: EN61000-4-5: 1 kV (power line)

2 kV line to ground (power line)

Immunity Conducted Disturbance: EN61000-4-6: 3 V (0.15 to 80 MHz)

Immunity Voltage Dip/Interrupting: EN61000-4-11: 0.5 cycle, 0, 180°, 100% (rated voltage)

Weight Approx. 200 g

K3MA-F

■Characteristics

■Measuring Ranges

No-voltage Contact/Open Collector Inputs

■Input/Output Ratings

Relay Contact Output

Input signal No-voltage contact (30 Hz max., ON/OFF pulse width: 15 ms min.)

Voltage pulse (5 kHz max., ON/OFF pulse width: 90 μs min., ON voltage: 4.5 to 30 V/OFF voltage:

0 to 2 V)

Open collector (5 kHz max., ON/OFF pulse width 90 μs min.)

Connectable Sensors

ON residual voltage: 2.5 V max.

OFF leakage current: 0.1 mA max.

Load current: Must have switching capacity of 15 mA min.

Must be able to dependably switch a load current of 5 mA max.

Measuring accuracy ±0.1%FS ±1 digit (at 23±5°C)

Measurement method Cycle measurement

Max. displayed digits 5 digits (−19999 to 99999)

Display 7-segment digital display, Character height: 14.2 mm

Polarity display “−” is displayed automatically with a negative input signal.

Zero display Leading zeros are not displayed.

Scaling function Programmable with front-panel key inputs (range of display: −19999 to 99999).

The decimal point position can be set as desired.

Hold function Max hold (maximum value), Min hold (minimum value)

Hysteresis setting Programmable with front-panel key inputs (0001 to 9999).

Other functions Scaling teach function

Display color change (green (red), green, red (green), red)

OUT type change (upper limit, lower limit, upper/lower limit)

Average processing (simple average OFF/2/4/8 operations)

Auto-zero time

Startup compensation time

Setting change lockout

Parameter initialization

Display auto-return time

Output Relays: 2 SPST-NO

Delay in comparative outputs 750 ms max.

Degree of protection Front panel: NEMA4X for indoor use (equivalent to IP66)

Rear case: IEC standard IP20

Terminals: IEC standard IP00 + finger protection (VDE0106/100)

Memory protection Non-volatile memory (EEPROM) (possible to rewrite 100,000 times)

Input Measuring range Measuring accuracy Displayable range

No-voltage contact (30 Hz max.) with

ON/OFF pulse width of 15 ms min.

0.05 to 30.00 Hz ±0.1% FS ±1 digit max.

(at 23±5°C)

–19999 to 99999

(with scaling function)

Open collector (5 kHz max.) with

ON/OFF pulse width of 90 μs min.

0 to 5 kHz

Item Resistive load (cosφ = 1) Inductive load (cosφ = 0.4, L/R = 7 ms)

Rated load (UL ratings) 5 A at 250 VAC, 5 A at 30 VDC 1 A at 250 VAC, 1 A at 30 VDC

Rated carry current 5 A max. (at COM terminal)

Max. contact voltage 250 VAC, 150 VDC

Max. contact current 5 A (at COM terminal)

Max. switching capacity 1,250 VA, 150 W 250 VA, 30 W

Min. permissible load

(P level, reference value)

10 mA at 5 VDC

Mechanical life 5,000,000 times min. (at a switching frequency of 1,200 times/min)

Electrical life

(at an ambient temperature of 20°C)

100,000 times min. (at a rated load switching frequency of 10 times/min)

K3MA-F

Connections

■Terminal Arrangement

■Block Diagram

■Input Circuits

Pulse Input

Power

supply Output

terminals

Input

terminals

External power supply

−

Models with

comparative

output

OUT1

OUT2100- to 240-VAC type or

24-VAC/VDC type

(No polarity for 24-VDC

connection.)

Note: Refer to Input Circuits on page 5.

12 V

40 mA

Terminal No. Name Description

Operation power Connects the operation power supply.

Pulse input No-voltage contact/open collector input

Outputs Outputs the relay outputs.

External power supply Use as the power supply for sensors.

A1 - A2

E4 , E6 - E5

E1 , E2 - E3

B5 - B6

InputInput circuit

Micro-

computer

Key

Display

Output

circuit

Contact output

(See note.)

Power supply circuit

Constant voltage circuit

EEP ROM

5 V12 V

Note: Relay output models only.

−B6

The negative pole of the sensor power

supply and COM are connected

internally.

Pulse

detection

circuit

Voltage

detection

circuit

Voltage pulse

PNP

NPN

12 V

200 Ω

1 kΩ

10 kΩ

NPN, contact input

PNP, voltage pulse input

K3MA-F

Operation

■Main Functions

Input Types and Ranges

Pulse Frequency Selection

Note: The default value is “0 to 5 kHz (5k).”

Scaling

When the desired display value is set for a corresponding input, the value will be displayed on a line between two points determining the zero point.

Frequency range

(setting parameter)

Function Input range (setting parameters) Setting range

Pulse frequency selection

(p-fre)

Selects pulse input signal. 0.05 to 30.00 Hz (30) Displayable from −19999 to 99999

with scaling function.

The position of the decimal point

can be set as desired.

0 to 5 kHz (5k)

Parameter Setting value Meaning

p-fre 30 0.05 to 30.00 Hz

measurement range

5k 0 to 5 kHz measure-

ment range

Parameter Setting value Meaning Parameter Setting value Meaning

inp 0 to 99999 Input value for dsp dp %.%%%% Display four digits after decimal point

dsp -19999 to 99999 Display value for inp %%.%%% Display three digits after decimal point

%%%.%% Display two digits after decimal point

%%%%.% Display one digit after decimal point

%%%%% No decimal point

The decimal point can be optionally displayed.

Display value

DISPLAY

Input value

INPUT

Teaching with actual values is possible.

Instead of setting by inputting with the Up Key and Shift Key, current values can be

input as scaling input values for teaching. This is useful for making settings while checking the

operation status of the K3MA-F.

The initial value will change depending on the

pulse frequency selection.

When displaying the decimal point, consider the

number of digits to follow the decimal point prior to

setting the scaling display value.

If p-fre is set to 30, the initial setting for the

decimal display will be 000.00.

Note:

K3MA-F

Convenient Functions

Scaling Teach

The parameter (inp) for the K3MA-F’s initial setting level can be set using actual input values with the teaching function. After displaying the param-

eter, the actual input settings can be made with the following operation.

OUT Types (Comparative Output Models Only)

OUT 1 and OUT 2 can be set to operate in one of the three following

modes in accordance with the compared values:

•Upper limit (High Acting):

The output is turned ON when the measurement value is greater

than its set value.

•Lower limit (Low Acting):

The output is turned ON when the measurement value is less than

its set value.

•Upper and lower limits (Outside Band Acting):

An upper limit (H set value) and lower limit (L set value) can be set

independently.

The output is turned ON when the measurement value is greater

than upper-limit set value or less than the lower-limit set value.

The three types of output operations shown above can be combined as desired. The following are examples of possible combinations.

Parameter Initialization

This function returns all of the parameters to their initial values.

Use this to reset the K3MA-F after returning it to its factory-set condi-

tion.

“T” lights to

indicate that the

parameter is valid

for teaching.

Next parameter

Monitor mode

Teaching mode

“T” turns OFF.

“T” flashes.

Normal change

Use to

monitor mode.

Use to shift to

the next parameter

without registering.

Parameter Set value Meaning

out1.t

out2.t

hi Upper limit: Upper-limit alarm

operation

lo Lower limit: Lower-limit alarm

operation

hi-lo Upper and lower limits: Upper-

and lower limit alarm operation

Upper Limit (High Acting)

OUT1 value

Hysteresis

OFF

OutputON

OFF

OutputON

OFF

Output

Measurement valueMeasurement valueMeasurement value

OUT1 upper-limit

value

OUT1 lower-limit

value

Lower Limit (Low Acting)Upper and Lower Limits

(Outside Band Acting)

Upper Limit 2-stage Output

Measurement

value

Measurement

value

Measurement

value

OUT2

value

OUT2 upper-limit

value

OUT2 upper-limit

value

OUT1 lower-limit

value

OUT2 lower-limit

value

OUT2 lower-limit

value

OUT1 upper-limit

value

OUT2 ON

OFF

OUT1

OUT2 ON

OFF

OUT1

OUT2 ON

OFF

OUT1

value

OUT1 value

Threshold Output Combination of Upper Limit and

Upper/Lower Limits

Parameter Setting value Meaning

init off ---

on Initializes all parame-

ters.

K3MA-F

Average Processing

Average processing stabilizes the display by minimizing any pulsat-

ing or flicker caused by fluctuations in the pulse width of sensor input

or by eccentricity in rotating shafts.

Hysteresis (Comparative Output

Models Only)

The hysteresis of comparative outputs can be set to prevent chatter-

ing in the output when the measurement value fluctuates finely near

the OUT value.

Auto-zero Time

This function sets the time for the display to return to zero when input

pulses stop. Set the time longer than the expected input pulse cycle

(the interval between one input pulse and the next). Proper measure-

ment is not possible if the time is set shorter than the input pulse

cycle.

Setting range: 0.0 to 19.9 s

Startup Compensation Time

The startup compensation time is the time to wait for the

measurement operation to be entered after the power supply of the

K3MA-F is turned ON. Use this parameter to cancel measurement

and comparative output operation until the a rotating body reaches

its normal speed when the power supply to the K3MA-F and rotating

body are turned ON at the same time.

Changing the Display Color

The color of the value displayed can be set to either red or green. For

comparative output models, the display color can be set to change

from green to red, or from red to green, according to the status of the

comparison criterion.

Display Auto-return Time

This function automatically returns the display to the operation level’s

current value if no keys are pressed for a preset time (called the dis-

play auto-return time).

Move-to-Protect-Level Time

The time required to shift to the protect level can be set as desired.

MAX/MIN Display

The maximum and minimum measurement (display) values from the

time the power is turned ON until the current time can be stored and

displayed. This is useful, for example, when measuring the maximum

value.

Upper limit (high acting)

Measurement value

Set valueHysteresis

OutputOFF

Display

Time

Startup

compensation

time

Lower limit

setting

(OUT2)

Power supply

00000 displayed

OUT2

output

8.781

100.05

113.36

OUT1 value

OUT2 value

Red

Green

MAX/MIN

Current value

MAX value

MIN value

MAX/MIN LEVEL MODE SHIFT UP

Min

Max

K3MA-F

Nomenclature

Name Functions

1. Main indicator Displays current values, parameter names (abbreviations), and comparative value settings.

2. Opera-

tion indica-

tors

1 Lit when output 1 is ON.

2 Lit when output 2 is ON.

SV Lit when a set value is being displayed or changed.

Max Lit when the main indicator is showing the MAX value.

Min Lit when the main indicator is showing the MIN value.

T Lit when the teaching function is operable. Blinks while the teaching function is operating.

3. Level indicator Displays the current level that the K3MA-F is in. (See below for details.)

4. MAX/MIN Key Used to display the MAX and MIN values when a measurement value is being displayed.

5. Level Key Used to change the level. The level can be switched between operation level and initial setting level.

6. Mode Key Used to allow the main indicator to indicate parameters sequentially.

7. Shift Key Used to enable a set value to be changed. When changing a set value, this key is used to move along the digits.

8. Up Key Used to change a set value. Used to set or clear a forced-zero function when a measurement value is being displayed.

Level indicator Level

pProtect

Not lit Operation

sInitial setting

fAdvanced function setting

MAX/MIN LEVEL MODE SHIFT UP

Max

Min

2. Operation indicators

3. Level indicator

4. MAX/MIN key

5. Level key 6. Mode key 7. Shift key

8. Up key

1. Main indicator

K3MA-F

Dimensions

Application Examples

A B C D E

UP SHIFT MODE LEVEL MAX/MIN

101.2

1.3

44.8

45+0.5

92+0.5

Terminal cover

(provided) Main indicator

character size Panel cut-out

7.6 mm

14.2 mm

120 min.

75 min.

The K3MA-F uses M3 terminals.

A terminal cover is provided.

Mounting Recommended Panel Thickness

1 to 8 mm.

Mount the product horizontally.

Displaying conveyor

belt feed speed

Monitoring the rotations

of a mixer or churner

Displaying the monitor

output from an inverter

as rotations or line speed

Gear Mixer or churner

K3MA-F

Inverter

Motor Voltage pulse

Note: If the monitor output from the inverter is analog,

such as 0 to 10 V, use the K3MA-J.

K3MA-F

K3MA-F m/min rpm

rpm

Proximity sensor

• Monitoring line speed for a reflow

furnace

• Displaying feed speed for food

processing, conveying, sintering

• Mixers for resin molding

• Powdering/pelleting machines,

centrifugal separators

• Monitoring conveyor speed

• Machining equipment (grinders,

polishers)

K3MA-F

Installation

1. Insert the K3MA-F into the panel cut-out hole.

2. For a waterproof installation, insert the rubber gasket onto the

body of the K3MA-F.

3. Fit the adaptor into the grooves on the left and right sides of the

rear case, then push it until it contacts the panel to secure the

K3MA-F.

■LCD Angle of View

The K3MA is designed to provide the best visibility at the angles

shown in the following diagram.

■Watertight Cover

Y92A-49N

■Rubber Packing

K32-P1

If the rubber packing is lost or damaged, it can

be ordered using the following model number:

K32-P1.

(Depending on the operating environment,

deterioration, contraction, or hardening of the

rubber packing may occur and so, in order to

ensure the level of waterproofing specified in

NEMA4, periodic replacement is

recommended.)

Note: Rubber packing is provided with the

Controller.

■Wiring Precautions

•Use crimp terminals.

•Tighten the terminal screws to a torque of approximately 0.5 N⋅m.

•To avoid the influence of noise, route signal lines and power lines

separately.

■Wiring

•Use the following M3 crimp terminals.

■Unit Labels (Provided)

•The unit labels are not attached to the K3MA-F. Select the desired

labels from the provided sheet.

Note: For scales and gauges, use the unit labels that are specified by

the relevant laws or regulations.

10°

30°

5.8 mm max.

K3MA-F

Operating Procedures

■Operations in Run Mode

■Levels

“Level” refers to a grouping of parameters. The following table lists the operations that are possible in each of the levels, and the diagram tells how

to move between levels. There are some parameters that are not displayed for certain models.

Level name Function Measurement

Protect Setting lockouts. Continue

Operation Displaying current values, and setting OUT 1/2 set values. Continue

Initial setting Making initial settings of input type, scaling, output operating action,

and other parameters.

Stopped

Advanced function setting Setting average processing, display color settings, and other ad-

vanced function parameters.

Stopped

Checking the Maximum and Minimum Values

The maximum and minimum values can be displayed by pressing the MAX/MIN Key while

the measurement is being displayed.

The maximum and minimum values can be reset by pressing the MAX/MIN Key for 1 s

min. when the maximum or minimum value is displayed.

Checking and Setting Comparative Set Values (for

Models with the Comparative Output Function)

Each time the Mode Key is pressed when the measurement value, maximum value, or

minimum value is displayed, the comparative values will be displayed in the following

order: OUT1 value (or OUT1 upper-limit value, OUT1 lower-limit 1), OUT 2 value (or

OUT2 upper-limit value, OUT2 lower limit value 2).

Note: When the comparative value is displayed, it can be changed by pressing the Shift

Key and the Up Key (when key protection is OFF).

Measurement

value

MAX value MIN value

MAX/MIN Key MAX/MIN KeyMAX/MIN Key

Measurement

value

MAX value

MIN value

OUT1 upper-

limit value

OUT1

value

OUT2

value

OUT1 lower-

limit value

OUT2 upper-

limit value

OUT2 lower-

limit value

Power ON

Operation level Protect level

Initial setting level

Advanced function

setting level

Measurement in progress

Measurement stopped

Level change

Level Key Level Key

Level Key

1 s min.

Password input

Level Key

MODE Key

Level Key

MODE Key

for at least user-set time

1 s min.

3 s min.

1 s min.

K3MA-F

■Parameters

−

For models with the

comparative output

function.

MODE

Set one of these.

Current value

OUT1

value

OUT2

value

OUT1

upper-limit

value

OUT2

upper-limit

value

OUT1

lower-limit

value

OUT2

lower-limit

value

Power ON

Operation level

Note: 1. Some parameters are not displayed for certain models.

2. The K3MA-F will stop measurement if the level is changed to the initial setting level or

the advanced-function setting level.

3. If the input range is changed, some parameters are set to default values. Therefore,

set the input range first.

4. Settings displayed in reversed colors are defaults.

K3MA-F

−

−−

−

Models

with the

compara-

tive output

function

Models

with the

compara-

tive

output

function

Pulse frequency

Scaling

Pulse

frequency

MODE MODE

MODE

Press Level

Key for

more than 3 s.

Press Level

Key for

more than 1 s.

Initial setting level Advanced-function

setting level

Enter

password

"-0169"

Press Level Key for less than 1 s.

Scaling

input

value

Scaling

display

value

Decimal

point

position

Move to

advanced-

function

setting level

OUT1 type

OUT2 type

Upper Limit

Lower Limit

Upper/Lower

Limits

Upper Limit

Lower Limit

Upper/Lower

Limits

Parameter

initialization

Average

processing

OUT1

hysteresis

OUT2

hysteresis

Auto-zero

time

Startup

compensation

time

Display

color

change

Display

auto-return

time

Move-to-

protect-

level time

Settings displayed in reversed colors are initial settings.

Unit: s

Unit: times

Comparative hysteresis

Green (red)

Red (green)

Red

Green

To change a setting, press the Shift Key again, and then

make the change with the Up Key .

K3MA-F

Operation/Adjustment Lockouts

Restricts key operations for operation level and adjustment level.

•Initial setting is 0.

•This is not displayed on models with no comparative output func-

tion.

Setting Level Lockouts

Restricts shifting to initial setting level or advanced function setting

level.

Setting Change Lockout

Restricts setting changes by key operation. When this lockout is set,

it is no longer possible to shift to a setting change mode.

However, all protect level parameters can still be changed.

■Initial Settings

/ /

Operation level

Press Level Key + Mode Key for more than 1 s.

Press Level Key + Mode Key for more

than preset time.

Protect level

MODE

Operation/adjustment

lockouts

Setting level lockouts

Setting change lockout

Parameter Setting Operation level

Current value

display

Set value

display

oapt 0Allowed Allowed

1Allowed Allowed

2Allowed Prohibited

Parameter Setting Shift to initial

setting level

Shift to

advanced

function

setting level

icpt 0 Allowed Allowed

1Allowed Prohibited

2Prohibited Prohibited

Parameter Setting Setting change by key

operation

wtpt off Allowed

on Prohibited

Select the pulse frequency for measurement.

Set the scaling values and OUT type as required.

Press the Level Key for 3 s min. to move to the initial setting

level.

Press the Level Key for more than 1 second to return to

the operation level.

If required, shift to the advanced-function setting level to set

the number of measurements for average processing,

hysteresis values, auto-zero time, startup compensation time,

display color change, display auto-return time, or move-to-

protect-level time.

Power ON

Measurement starts.

Specify set value of OUT 1 and 2.

K3MA-F

■Setting Example

Initial Settings

The settings for the following example are shown here.

Example: Display conveyor belt feed speed

Here, the conveyor belt feed speed is to be displayed in units of

0.1 m/min.

•Proximity Sensor: E2E-X5E1, NPN output

When displaying a flowrate (e.g., in l/min or l/h), make the scaling

settings after confirming the I/O characteristics of the flowrate sen-

sor. There are flowrate sensors that output analog signals. If this kind

of flowrate sensor is used, consider using the K3MA-J.

1. Select the maximum input frequency for the K3MA-F.

Set the pulse frequency selection to either 30 Hz or 5 kHz. In the

example, this is set to 30 Hz because the conveyor belt is turning

at a slow speed.

Parameter: p-fre (pulse frequency), Setting value: 30

2. Set the scaling. The display value (D) is shown with the following

formula.

D = f × α,

f: frequency and

α: prescaling value

The value of α will be internally calculated and registered if the

input value (f) and the display value (D) are set.

The number of rotations or speed is shown with the following for-

mula.

Rotations (rpm) = Frequency input/No. of pulses

per rotation × 60

Cycle speed D (m/min)= Rotations × roll circumference

= 1/N × f × 60 × d × π

N: No. of pulses per rotation

f: Frequency (Hz)

d: Roller diameter (m)

When the input conditions are applied to this equation, we obtain

the following:

Display value = 1/1 × f × 60 × 0.1 × π

For an input of 1 Hz, the display value is 18.8495 (m/min).

The scaling settings for the K3MA-F must be integers. Also, to

decrease error, the scaling value is multiplied by 1,000, to obtain

an input of 1000 Hz and a display value of 18850. However,

because the display value in this case is displayed to the first dec-

imal place, the scaling is set as shown in the following example so

that 1885.0 is displayed for an input of 100 Hz.

Parameter Setting value

inp (scaling input value) 100

dsp (scaling display value) 18850

dp (decimal point position) %%%%.%

Note: The decimal point position here refers to the position in the

number after scaling. When setting the scaling display value, it

is necessary to consider the number of digits to be displayed

past the decimal point.

■Troubleshooting

When an error occurs, error details will be displayed on the main indicator. Confirm the error from the main indicator and take the appropriate coun-

termeasures.

E2E-X5E1

Proximity Sensor

K3MA-F-A2 100-240VAC

0.1 m

MAX/MIN LEVEL MODE SHIFT UP

Max

Min

dsp

18850

inp

100

1 pulse/rotation, roller diameter 0.1 m

Display value

Input value

Level

display

Main indicator Error contents Countermeasures

Not lit e111 RAM memory error Repair is necessary.

Consult your OMRON sales representative.

5e111 EEPROM memory error When this error is displayed, press the Level Key for 3 sec-

onds, and the settings will be restored to the factory set-

tings.

If the error cannot be recovered, repair is necessary. Con-

sult your OMRON sales representative.

Not lit Flashes 99999 The scaling display value exceeds 99999. Promptly change the input to a value that falls within the

specified range.

The scaling value may be inappropriate. Review the scal-

ing value at the initial setting level.

Not lit Flashes -19999 The scaling display value is lower than −19999. Promptly change the input to a value that falls within the

specified range.

The scaling value may be inappropriate. Review the scal-

ing value at the initial setting level.

In the interest of product improvement, specifications are subject to change without notice.

ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.

To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.

Terms and Conditions Agreement

Read and understand this catalog.

Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you

have any questions or comments.

Warranties.

(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship

for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron

disclaims all other warranties, express or implied.

(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT

NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER

ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE

PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.

Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the

Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at

Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or

replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount

equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,

repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products

were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate

modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall

not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or

electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,

recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above

warranty.

See http://www.omron.com/global/ or contact your Omron representative for published information.

Limitation on Liability; Etc.

OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,

LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,

WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.

Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.

Suitability of Use.

Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the

combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable

third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself

is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,

system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product

with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.

NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE

QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,

AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE

OVERALL EQUIPMENT OR SYSTEM.

Programmable Products.

Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence

thereof.

Performance Data.

Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining

suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate

it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.

Change in Specifications.

Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our

practice to change part numbers when published ratings or features are changed, or when significant construction changes are

made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers

may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at

any time to confirm actual specifications of purchased Product.

Errors and Omissions.

Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is

assumed for clerical, typographical or proofreading errors or omissions.

2014.10

In the interest of product improvement, specifications are subject to change without notice.

OMRON Corporation

Industrial Automation Company

http://www.ia.omron.com/

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Omron:

K32-49HC K3MA-F 24VAC/VDC K3MA-F-A2 24VAC/VDC K32-49SC