Amphenol 162GB Series Miniature Bayonet Lock Connectors CONTENTS Pages * 2 2 2 3-4 * * * * * * * * * * * * * * * * * * * * * * Amphenol Introduction to 162GB Crimp Connectors Audio Applications Cable Assembly Facilities at Amphenol Ltd MIL-C-26482 Qualification Approval Tests DEF 5325 Qualification Approval Tests Table of Shell Styles Insert Availability and Voltage Ratings How to Order 162GB Crimp Connectors Box Mounting Receptacles Single Hole Fixing Receptacles Cable Mounting Receptacles Plugs Plugs with optional Coupling Rings Cable Accessories Cables to DEF 10 Accessories Dust Caps AIA Backshells - Interconnection Accessories Interconnection Accessories Installation Procedure Interconnection Accessories Shield Term Process Key/keyway Orientations Insert Orientations 162GB Crimp Assembly Instructions 5 6-7 8 9-10 11-12 13-14 15-16 17-18 19 20 21-28 29-31 32-33 34 35 36 37-42 Amphenol 162GB Crimp Connectors DESIGNED TO COMPLY WITH MIL-C-26482 AND BS 9522-N0001, THE SUCCESSOR TO DEF 5326 Patt. 603 Development and manufacture of 162GB miniature bayonet lock connectors has been closely coordinated with the solder version. The entire programme has been carried out at Amphenol's Whitstable Plant. The precision machinery and measurement control processes used for the production of 162GB crimp connectors are the same as those used to produce 62GB solder connectors. Full intermountability absolutely guaranteed. and intermateability Audio Applications Contacts are suitable for tinsel cord applications. are 162GB Series crimp connectors share many of the features of 62GB solder connectors. Coupling is achieved with a triple-track bayonet locking system which gives positive alignment on all shell sizes. When connector halves are fully mated there is a definite click. Inspection holes in the coupling ring will then reveal the bayonet pins on the receptacle which are clearly marked in yellow. The Amphenol design means simplified removal of coupling rings for servicing or replacement as they are front demountable. In addition there is a rough grip heavy duty style for arduous conditions and a lever coupling ring which allows extremely close mounting of connectors. The method of sealing is the same as for 62GB connectors; using peripheral seals on the rubber inserts and sealing the mating shells with a square section gasket. Wire sealing is by multiple risers in the rear grommet. Derating Connectors must be derated under the following operating temperatures: 1. At elevated temperatures, the current ratings are reduced as show in the table on page 10. 2. At high altitudes, revised voltage ratings become effective as shown on page 11. Cable Assemblies Amphenol is fully equipped to undertake the preparation of all types of cable assemblies complying with the military vehicles and engineering establishments and fighting vehicles requirements of the Ministry of Defence - the Ministry of Environment (Motorways) for motorway control equipment - the Post Office manufacturing code and to the British Standards Institute when applicable to Cable systems. Control procedures carried out in accordance with MIN DEF 05-21. Approval numbers BS 9000, 1043/M and CAA AD/1450/58. Moulded terminations form a specialised service by the company. The process offers such advantages as a waterproof seal between cable and connector back-end, mechanical protection, and a homogeneous joint between moulding and cable. Other Amphenol Products Amphenol products include: printed circuit, rack and panel, microminiature, audio; hermetic and R.F. connectors; integrated circuit components; trimming and precision potentiometers; concentric and digital microdials; cable, cable assemblies; fans and blowers; relays and keys; chokes and coils; R.F. coaxial switches. 3. When connectors to different specifications are intermated (e.g. BS 9522-N001 and MIL-C-26482), the combination must not be operated under conditions more severe than the less stringent clause of either specification. Amphenol 162GB connectors are designed to meet the most stringent requirements of both specifications. 2 Amphenol 162GB Series DESIGNED TO COMPLY WITH MIL-26482 SCHEDULE OF TESTS REQUIRED FOR QUALIFICATION APPROVAL Tests Brief Description Examination of Product Maintenance Ageing Crimp only There is no damage to the contacts or connectors after 10 removals and insertions of the contacts Contact Insertion and Removal Forces Crimp only Insertion - does not exceed 66.7 N (15lbf.) For individual contacts. Removal - does not exceed 44.5N (10lbf.) Contact Retention Crimp Contact Contact locking mechanisms withstands the following minimum axial forces: CONTACT SIZE 20 16 12 FORCE (N) 89 111 133 FORCE (LBF) 20 25 30 Axial displacement does not exceed 0.304mm (0.012in) when pressure is applied from face side. Operating Forces Torque measurement of mating and unmating. Ranges from 0.905 Nm. (8 lbf. in.) on shell size 8 to 4.971 Nm. (44 lbf. in.) on shell size 24 couplings. Insulation Resistance, Room Temperature Unmated connectors tested in accordance with Method 302 test condition B of MIL-STD-202. Dielectric Withstanding Voltage (Sea Level) Mated and unmated connectors tested in accordance with Method 301 of MIL-STD-202. Dielectric Withstanding Voltage (Altitude) Tested in accordance with Method 105, test condition C of MILSTD-202. After 30 minutes tested in accordance with Method 301 of MIL-STD-202 unmated and mated. Initial Contact Resistance Between 45 and 95 millivolts drop on wire sizes from 24 to 12. Crimp contacts to meet MIL-C-23216. Thermal Shock Unmated connectors tested in accordance with Method 107, condition B of MIL-STD-202 except min. temp is -55oC. Insulation Resistance at Elevated Temps (Short Time) Greater than 3 megohms 250 hr at 125 C (Long Time) o Greater than 12 megohms 1000 hr at 105oC Durability 500 cycles of coupling and uncoupling Vibration In accordance with Method 204 Condition B of MIL-STD-202 Shock Impulses of 50 G's duration of 11 1 milliseconds Moisture Resistance In accordance with Method 106 of MIL-STD-202 Corrosion Salt Spray to Method 101 Condition B of MIL-STD-202 Operating Forces From 0.905 Nm. (8 lb. In.) for shell size 8 to 4.971 Nm. (44 lb. in.) for shell size 24. Contact Resistance As per contact resistance test of MIL-C-23216. (a) Solvent Immersion Hydraulic Fluid Conforming to MIL-H-5606 20 hrs (b) Solvent Immersion Lubricating Oil Conforming to MIL-H-7808 20 hrs Insert Retention Effective pressure differential of 5 17.0 KN/m2 (75 p.s.i..) Insert Retention Hermetic Effective pressure differential of 13 80.0 KN/m 200 (p.s.i.) Contact Retention Crimp Axial loads between 6 6.67 N (15 lbf.) and 111.2 N (25 lbf.) 2 3 Protective Covers and Storage Tests Brief Description Examination of Product Components suitability after storage and use of recommended Protective Covers Operating Forces Measurement of Receptacles, Plugs and Protective Covers mating and unmating forces. Moisture Resistance Crimp Contacts to Method 106 of MIL-STD-202. Corrosion Salt Spray to Method 101, Condition B of MIL-STD-202. Cover Chains Tensile Strength 111.2 N (25 lbf.) from various directions Air Leakage 69.0 KN/m2 (10 p.s.i.) applied to inside of Protective Covers Crimp Contact Retention Feature Tests Brief Description Examination of Product Test to establish Crimp effectiveness Maintenance Ageing (Contacts only) Involves repeated insertion/removal of contacts and mating and unmating of connectors. Contact Retention Loads applied in both directions. Connector Assembly - Class J Tests Brief Description Examination of Product Thermal Shock In accordance with Method 107 Condition B of MIL-STD-202 Water Pressure Immersion 1.829 m (6 ft.) under water for solder type connectors Air Leakage Solder Receptacles 206.9 KN/m2 (30 p.s.i.) across connectors. Others to Method 112 Condition C, Procedure 1 of MIL-STD-202 4 Table of Shell Styles BOX MOUNTING RECEPTACLES BOX MOUNTING RECEPTACLES (4-hole Fixing) (4-hole Fixing) Page Page SINGLE HOLE FIXING RECEPTACLES Page PLAIN SHELL 162GB 12E THREADED SHELL GROMMET SEAL 162GB 30T 162GB 10E STRAIN RELIEF CLAMP (For details of Right 162GB Angle Strain Relief Clamps, see Page 20) 10F CABLE MOUNTING RECEPTACLES Page THREADED SHELL GROMMET SEAL 162GB 37T 162GB 14E 162GB 14F GROUNDED PLUGS Page NON GROUNDED PLUGS Page CC1304 CC1305 162GB 31T 162GB 36T 162GB 11E 162GB 16E 162GB 11F 162GB 16F 162GB 36TG STRAIN RELIEF CLAMP (For details of Right Angle Strain Relief Clamps, see Page 5 Insert Availability 8 10 12 14 16 18 20 8-03 10-06 12-10 14-12 16-23* 18-32 20-41 8-33 10-07 12-08 14-15 16-26 18-11 20-16 8-98 14-19 10-02 12-03 14-05 16-08 16-04 Notes Lettering of inserts shown above corresponds to views of front (mating) surface of pin inserts or rear face (cable accessory end) of socket inserts. KEY ? No. 16 size contacts ? No. 20 size contacts No. 12 size contacts 15 4 10 3 2 5 1 0 0 -55 -25 0 25 50 75 100 125 o AMBIENT TEMPERATURE C Current-temperature derating curve 6 CURRENT - AMPS PER CONTACT Due to the arrangement of contacts in the 14-12 insert arrangement it is classified, for current derating, in the shell size range 18-24. SIZE 16 CONTACTS 5 CURRENT - AMPS PER CONTACT * These insert arrangements are not included in Pattern 105 but are available and listed in MILC-26482. SIZE 20 CONTACTS Insert Availability Working Voltage 22 24 dc Working Voltage ac Working Voltage r.m.s. Proof Voltage Sea Level 700 500 500 300mb at 20oC 8.500m (27,800 ft) 375 265 265 44 mb at 20oC 20,000 m (66,000 ft) 200 140 140 Sea Level 1250 900 3250 300mb at 20oC 8.500m (27,800 ft) 550 390 1750 44 mb at 20oC 20,000 m (66,000 ft) 300 210 775 Altitude Rating 1 Rating 2 162GB only Rating 3 FLASHOVER VOLTAGE kW Working Voltage Working Voltages ** (nominal) d.c. or a.c. peak Voltage Proof d.c. or a.c. peak Sea Level 1013 mbart III 1500 8500m (27,900 ft) 320 mbar III 800 21,340m (70,000 ft) 44 mbar III 450 3000 1300 750 (Figures in bold type are from DEF STAN 59-35 (Part 1) Sec. 3 Patt. 105) 4 3 VOLTAGE RATING 2 2 NOTES Because safe working voltages at altitude above sea-level are dependent upon individual conditions of use, these values are not specified in DEF STAN 59-35 (Part 1) Sec. 3 Patt. 105 but approximate values are included here for the guidance of designs. 1 VOLTAGE RATING 1 0 20 40 60 80 100 120 140 160 180 (6) (12) (18) (24) (30) (36) (42) (48) (54) ALTITUDE - THOUSANDS OF FEET (METRES) Relationship between flashover voltage and altitude for each voltage rating VOLTAGE RATINGS Two categories of voltage rating are specified in DEF STAN 59-35 (Part 1) Sec. 3 Patt. 105. Rating 1 (700V d.c. working at sea-level) Applicable to the high contact density inserts shown in the upper section of the insert availability diagram above. Rating 2 (1250V d.c. working at sea-level) Applicable to the inserts shown in the lower section of the insert availability diagram. Rating 3 (1500V d.c. working at sea-level) (a) Maximum current per individual contact (in isolation)* at ambient temperature of 85oC Contact Size 12: 23A (b) Maximum current per contact through all contacts simultaneously at an ambient temperature of 85oC Contact Size 12: 20A Altitude Derating Information on voltage derating for operation at altitudes above se-level can be obtained from the flashover voltage altitude curves on the left. 7 Ordering Amphenol 162GB Series Connectors Shell Style 162GB - 3 6 Insert Arrangement E 22 - Series Designation 162GB Shell Size (in sixteenths of an inch) 8, 10, 12, 14,16, 18, 20, 22, 24 Specification Key 1 Styles originally specified in MIL-C-26482 3 Styles exclusive to DEF STAN 59-35 (Part 1) Sec. 3 Number of Contacts 3, 5, 6, 7, 8, 10, 11, 12, 19, 21*, 23, 26, 32, 41, 55, 61 *consult factory for availability Shell Style 0 - Receptacle, wall mounting 1 - Receptacle, cable mounting 2 - Receptacle, box mounting 4 - Receptacle, internally threaded, with cable accessories as illustrated, for single hole mounting 6 - Plug, cable mounting 7 - Single hole fixing receptacle 36 P B (044) Contact Style P - Pins S - Sockets Orientation Keys/Keyways: B, C, E, F Inserts: W, X, Y, Z Environmental Code E - Insert seal and grommet seal with grommet nut (excluding 12E which has plain shell and no grommet nut) F - As (E) but grommet nut has integral strain relief clamp T -Threaded shell for cable accessories Deviations (218) Lever coupling ring (044) Rough grip heavy duty coupling ring (639) Bright cadmium plated shells (714) Cadmium Olive Drab (416) Electroless Nickel (608) Hard Black Anodised (771) Black Zinc Cobalt HOW TO ORDER FROM MS CONNECTOR NUMBERS Connector numbers in the AMPHENOL and MS numbering systems. Only alternative insert orientations are specified in MIL-C-26482 which does not include alternative key/keyway orientations MS31 162GB - 24 14 E E 18-11 18-11 P P X X 8 Box Mounting Receptacles Description Amphenol Part No Military No 30T 4-hole flange mounting with threaded shell to accept standard cable accessories 162 Series 162GB-30T etc 10E 4-hole flange mounting with grommet and grommet nut 162 Series 162GB-10E etc MS3120E etc 10F 4-hole flange mounting with grommet and grommet nut fitted with integral strain relief clamp 162 Series 162GB-10F etc MS 3120F etc 12E 4-hole flange mounting with plain shell for direct wiring to exposed solder buckets. Film wire terminations available on 62 Series as deviation (219). 162 Series style has integral grommet 162 Series 162GB-12E etc MS 3122E etc A Y G B F A X Thread A Y G F B A Y G H F B A L Y G F B A L 9 Dimensions and Mounting Details 162 OVERALL MATED DIMENSIONS Add the two relevant plug and receptacle overall dimensions and deduct: - 0.365 (9.271mm) for shell sizes 20, 22, 24 - 0.303 (7.696mm) for all other sizes Panel Receptacle Shell W When receptacles are mounted on the rear face of the panel, the maximum value for dimension W must not be exceeded otherwise the receptacle cannot be mated to a plug Panel thickness with screw head W max. Shell Size 08-18 in mm Shell Size in mm 0.100 2.540 20-24 0.210 5.330 `A' Overall Length Max Shell Size 08 10 12 14 16 18 20 22 24 Flange thickness 0.005 Shell (0.127) Size B in mm 08 10 12 14 16 18 20 22 24 0.062 1.575 0.062 1.575 0.062 1.575 0.062 1.575 0.062 1.575 0.062 1.575 0.080 2.03 0.080 2.03 0.080 2.03 30T in mm (162) 10E in mm (162) 10F in mm (162) 12E in mm (162) 12E in mm 1.286 32.665 1.286 32.665 1.286 32.665 1.286 32.665 1.286 32.665 1.286 32.665 1.348 34.24 1.348 34.24 1.348 34.24 1.320 33.53 1.320 33.53 1.320 33.53 1.320 33.53 1.320 33.53 1.320 33.53 1.382 35.10 1.382 35.10 1.382 35.10 1.759 44.68 1.759 44.68 1.759 44.68 1.733 44.02 1.873 47.575 1.873 47.575 2.115 53.72 2.115 53.72 2.247 57.075 1.286 32.665 1.286 32.665 1.286 32.665 1.286 32.665 1.286 32.665 1.286 32.665 1.348 34.24 1.348 34.24 1.348 34.24 0.917 23.29 0.917 23.29 0.917 23.29 0.917 23.29 0.917 23.29 0.917 23.29 0.980 24.89 0.980 24.89 1.023 29.895 Flange dim. max. sq. Flange hole centres TP C D in mm 0.817 20.75 0.942 23.925 1.036 26.315 1.130 28.70 1.223 31.065 1.317 33.45 1.442 36.625 1.567 39.80 1.692 42.98 `L' Shell Lengths in mm 0.594 15.09 0.719 18.26 0.812 20.625 0.906 23.10 0.969 24.61 1.062 26.575 1.156 29.36 1.250 31.75 1.375 34.925 Flange holes dia. 0.005 (0.127) -0.002 (-0.051) E in mm 0.120 3.05 0.120 3.05 0.120 3.05 0.120 3.05 0.120 3.05 0.120 3.05 0.120 3.05 0.120 3.05 0.147 3.735 Mtg. Flange location 0.005 (0.127) F in mm 0.445 11.3 0.445 11.3 0.445 11.3 0.445 11.3 0.445 11.30 0.445 11.3 0.555 14.095 0.555 14.095 0.590 14.985 Cable sleeve int. dia. 0.005 (0.127) Overall Rear dia. max. 30T in mm 0.434 11.02 0.558 14.17 0.683 17.35 0.808 20.52 0.933 23.70 1.057 26.85 1.182 30.02 1.307 33.20 1.432 36.37 12E in mm 0. 434 11.02 0.558 14.17 0.683 17.35 0.808 20.52 0.933 23.70 1.057 26.85 1.182 30.02 1.307 33.20 1.432 36.37 G 10E in mm 0.561 14.25 0.686 17.425 0.811 20.60 0.936 23.775 1.061 26.975 1.186 30.12 1.311 33.30 1.436 36.47 1.561 39.65 10F in mm 0.828 21.03 0.891 22.63 1.016 25.805 1.141 28.98 1.203 30.555 1.426 36.22 1.426 36.22 1.567 39.80 1.735 44.07 H 10F only in mm 0.156 3.96 0.188 4.775 0.312 7.925 0.375 9.575 0.500 12.7 0.625 15.875 0.625 15.875 0.750 19.05 0.800 20.32 Thread Shell ext. dia. Max. X Y in mm 7 /16-28 UNEF 9 /16-24 NEF 11 /16-24 NEF 13 /16-20 UNEF 15 /16-20 UNEF 11/16-18 NEF 13/16-18 NEF 15/16-18 NEF 17/16-18 NEF 0.473 12.015 0.590 14.99 0.750 19.05 0.875 22.225 1.000 25.4 1.125 28.575 1.250 31.75 1.375 34.925 1.500 38.1 10 Single Hole Fixing Receptacles Description A Single hole fixing with grommet and grommet nut. Has panel O-ring seal X Thread K G Y M B Amphenol Part No Military No 162 Series 162GB-14E etc 14E F A X Thread K G H 14F Single hole fixing with grommet and grommet nut fitted with integral strain relief clamp. Has panel O-ring seal 162GB Series 162GB-14F etc 37T Single hole fixing with threaded shell to accept accessories 162GB Series 162GB-37T etc M Y B F A X Thread K G Y M B F 11 Dimensions and Mounting Details 162 OVERALL MATED DIMENSIONS Add the two relevant plug and receptacle overall dimensions and deduct 0.365 (9.271mm) for shell sizes 20, 22, 24 0.303 (7.696mm) for all other sizes C J D R N K L 57A (219) 5016, 5005, 5024 SINGLE HOLE FIXING RECEPTACLES PANEL PIERCING DETAILS Shell Size 8 10 12 14 16 20 20 22 24 Shell Size 08 10 12 14 16 18 20 22 24 Mounting hole dia. 0.005 (0.127) Mounting hole crs. min. Diameter across flat 0.005 (0.127) R in mm S in mm N in mm 0.572 14.53 0.697 17.70 0.885 22.48 1.010 25.65 1.135 28.83 1.260 32.00 1.385 35.18 1.510 38.35 1.635 41.45 1.250 31.75 1.359 34.53 1.531 38.885 1.656 42.06 1.781 45.24 1.891 48.03 2.031 51.59 2.156 54.76 2.277 57.835 0.540 13.72 0.665 16.89 0.828 21.03 0.952 24.18 1.076 27.33 1.201 30.50 1.326 33.68 1.451 36.855 1.576 40.03 Panel Thickness Min. Overall Length Max. A Max. Shell Size K in mm 0.062 1.575 0.062 1.575 0.062 1.575 0.062 1.575 0.062 1.575 0.062 1.575 0.062 1.575 0.062 1.575 0.062 1.575 8 0.125 3.175 0.125 3.175 0.125 3.175 0.125 3.175 0.125 3.175 0.125 3.175 0.250 6.35 0.250 6.35 0.250 6.35 10 12 14 16 18 20 22 24 Flange thickness 0.005 (0.127) Mtg. Flange location 0.005 (0.127) B 14E 14F in mm F in mm 14E in mm G 14F in mm H 14F in mm in mm 0.117 2.97 0.117 2.97 0.117 2.97 0.117 2.97 0.117 2.97 0.117 2.97 0.148 3.76 0.148 3.76 0.148 3.76 0.706 17.93 0.706 17.93 0.706 17.93 0.706 17.93 0.706 17.93 0.706 17.93 0.894 22.71 0.894 22.71 0.927 23.55 0.713 18.11 0.838 21.29 0.963 24.46 1.088 27.625 1.213 30.81 1.338 33.975 1.463 37.16 1.588 40.325 1.713 43.51 0.828 21.03 0.891 22.63 1.016 25.805 1.141 28.97 1.203 30.555 1.426 36.22 1.426 36.22 1.567 39.80 1.735 44.07 0.156 3.96 0.188 4.775 0.312 7.925 0.375 9.525 0.500 12.7 0.625 15.875 0.625 15.875 0.750 19.05 0.800 20.32 0.750 19.05 0.875 22.225 1.062 26.975 1.187 30.15 1.312 33.32 1.437 36.50 1.562 38.675 1.687 42.85 1.812 46.05 Overall Rear diameter Cable Sleeve int. dia. 0.005 (0.127) (162) (162) 14E in mm 14F in mm 1.355 34.42 1.355 34.42 1.355 34.42 1.355 34.42 1.355 34.42 1.355 34.42 1.576 40.03 1.576 40.03 1.609 40.87 1.759 44.68 1.759 44.68 1.759 44.68 1.733 44.02 1.873 44.575 1.873 44.575 2.105 53.47 2.105 53.47 2.247 57.075 Fixing Nut A/F Fixing nut thread Thread flat +0.000 -0.005 (-0.127) Shell Ext dia. Max. L X M Y in mm in mm 0.527 13.3 0.652 16.56 0.815 20.70 0.939 23.85 1.063 27.00 1.188 30.175 1.313 33.35 1.438 36.53 1.563 39.70 0.473 12.025 0.590 14.99 0.750 19.05 0.875 22.225 1.000 25.40 1.125 28.575 1.250 31.75 1.375 34.925 1.500 38.10 9 /16-24 NEF 11 /16-24 NEF ? - 20 UNEF 1-20 UNEF 1? -18 NEF 11/4 -18 NEF 1? -18 NEF 11/2 -18 NEF 1? -18 NEF 12 Cable Mounting Receptacles Description Amphenol Part No 31T Basic cable mounting receptacle with threaded shell to accept standard cable accessories 162 Series 62GB-31T etc 11E Cable mounting receptacle with grommet and grommet nut 11F Cable mounting receptacle with grommet and grommet nut fitted with integral strain relief clamp Military No X THREAD 162 Series 162GB-11E etc 162 Series 162GB-11F etc MS 3121F etc 13 Dimensions and Mounting Details 162 OVERALL MATED DIMENSIONS - Add the two relevant plug and receptacle overall Dimensions and deduct: - 0.365 for shell sizes 20, 22, 24 (9.271) 0.303 for all other sizes (7.696) `A' Overall Length Max. Shell Size 31T in mm (162) 11E in mm (162) 11F in mm 08 1.286 32.665 1.286 32.665 1.286 32.665 1.286 32.665 1.286 32.665 1.286 32.665 1.348 34.24 1.348 34.24 1.348 34.24 1.320 33.53 1.320 33.53 1.320 33.53 1.320 33.53 1.320 33.53 1.320 33.53 1.382 35.10 1.382 35.10 1.382 35.10 1.759 44.68 1.759 44.68 1.759 44.68 1.733 44.02 1.873 47.575 1.873 47.575 2.115 53.72 2.115 53.72 2.247 57.07 Flange dimensions max. sq. Flange location 0.005 (0.127) C F 10 12 14 16 18 20 22 24 Shell Size 08 10 12 14 16 18 20 22 24 Flange thickness ness 0.005 (0.127) B Overall rear diameter Max. in mm in mm in mm G 11F in mm 0.094 2.39 0.094 2.39 0.094 2.39 0.094 2.39 0.094 2.39 0.094 2.39 0.104/0.100 2.64/2.55 0.104/0.100 2.64/2.55 0.104/0.100 2.64/2.55 0.817 20.75 0.942 23.925 1.036 26.315 1.130 28.70 1.223 31.065 1.317 33.45 1.442 36.63 1.567 39.80 1.692 42.98 0.415 10.54 0.415 10.54 0.415 10.54 0.415 10.54 0.415 10.54 0.415 10.54 0.535 13.59 0.535 13.59 0.560/0.574 14.225/14.58 0.828 21.03 0.891 22.63 1.016 25.805 1.141 28.97 1.203 30.555 1.426 36.22 1.426 36.22 1.567 39.80 1.735 44.07 Cable Sleeve int. dia. 0.005 (0.127) 11E in mm H 11F in mm 0.561 14.25 0.686 17.425 0.811 20.60 0.936 23.775 1.061 26.95 1.186 30.125 1.311 33.30 1.436 36.745 1.561 39.65 0.156 3.96 0.188 4.775 0.312 7.925 0.375 9.525 0.500 12.7 0.625 15.875 0.625 15.875 0.750 19.05 0.800 20.32 Thread X 31T Shell ext. dia. Max. Y in mm 7 /16-28 UNEF 9 /16-24 NEF 11 /16-24 NEF 13 /16-28 UNEF 15 /16-20 UNEF 11/16-18 NEF 13/16-18 NEF 15/16-18 NEF 17/16-18 NEF 0.473 12.025 0.590 14.99 0.750 19.05 0.875 22.225 1.000 25.4 1.125 28.575 1.250 31.75 1.375 34.925 1.500 38.10 14 Plugs Description Amphenol Part No 36T Basic plug with threaded shells to accept standard cable accessories 162 Series 162GB-36T etc 36TG Basic plug with grounding spring, threaded shell to accept standard cable accessories 162 Series 162GB-16E etc 16E Plug with grommet and grommet nut 162 Series 162GB-16E etc MS 3126E etc 16F Plug with grommet and grommet nut fitted with integral strain relief clamp 162 Series 162GB-16F etc MS3126F etc X Thread Military No 15 Dimensions and Mounting Details `A' Overall Length max. 36T and 36TG in mm 16F in mm (162) 16E in mm 1.277 32.44 1.277 32.44 1.277 32.44 1.277 32.44 1.277 32.44 1.277 32.44 1.277 32.44 1.277 32.44 1.277 32.44 1.752 44.50 1.752 44.50 1.752 44.50 1.726 43.84 1.866 47.40 1.866 47.40 2.045 51.94 2.045 51.94 2.178 55.32 1.310 33.27 1.310 33.27 1.310 33.27 1.310 33.27 1.310 33.27 1.310 33.27 1.310 33.27 1.310 33.27 1.310 33.27 Shell Size 08 10 12 14 16 18 20 22 24 Overall dia. Max. Coupling Ring dia. max. C Y 162 OVERALL MATED DIMENSIONS - Add the two relevant plug and receptacle overall Dimensions and deduct: - - 0.365 (9.271mm) for shell sizes 20, 22, 24 0.303 (7.696mm) for all other sizes Overall rear diameter Max. Shell Size 08 10 12 14 16 18 20 22 24 G in mm in mm 16E in mm 0.750 19.05 0.859 21.82 1.031 26.19 1.156 29.36 1.281 32.54 1.391 35.33 1.531 38.89 1.656 42.06 1.777 45.135 0.750 19.05 0.859 21.82 1.031 26.19 1.156 29.36 1.281 32.54 1.391 35.33 1.531 38.89 1.656 42.06 1.777 45.135 0.561 14.25 0.686 17.425 0.811 20.60 0.936 23.775 1.061 26.95 1.186 30.125 1.311 33.30 1.436 36.745 1.561 39.65 Cable Sleeve int. dia. 0.005 (0.127) 16F in mm H 16F in mm 0.828 21.03 0.891 22.63 1.016 25.805 1.141 28.97 1.203 30.555 1.426 36.22 1.426 36.22 1.567 39.80 1.735 44.07 0.156 3.96 0.188 4.775 0.312 7.925 0.375 9.525 0.500 12.7 0.625 15.875 0.625 15.875 0.750 19.05 0.800 20.32 16 Plugs with optional Coupling Rings W Description Amphenol Part No (044) Heavy duty coupling ring. Available for any of the plugs listed on page 22 To order complete assembly, add deviation (044) to connector number 162 Series 162GB-XXXXX-XX(044) (218) Lever coupling ring. Mating and unmating only requires 120o movement. Available in shell size 14 and 16 only. Other sizes to special order. 162 Series 162GB-XXXXX-XX(218) Dimensions and Mounting Details HEAVY DUTY COUPLING RINGS Shell Size W Overall dia. max. W (044) in mm 0.870 22.1 0.979 24.865 1.151 29.235 1.276 32.41 1.401 35.585 1.505 38.225 1.651 41.935 1.776 45.11 1.897 48.18 08 10 12 14 16 18 20 22 24 LEVER COUPLING RINGS Shell Size A Max in mm C Max. in mm 14 1.444 36.67 1.444 36.67 0.787 19.98 0.844 21.43 16 AUDIO CONNECTORS FOR TINSEL CORD Shell Size 10 A Max in mm 162GB-0506-10-6PX 162GB-5001-10-7SX 162GB-0506-10-7PX 2.375 60.325 2.75 69.85 B dia. Max in mm H Cable Outlet Min in mm 0.875 22.225 0.276 7.01 17 Cable Accessories SUITABLE FOR ALL EXTERNALLY THREADED PLUG OR RECEPTACLE SHELLS Description 214 Grommet seal and nut. Provides an environmental seal for the exposed solder buckets in the openback class T shells. Amphenol Part No 162 Series 162GB-214-XX For Shell sizes 08-24 respectively Grommet nut only for 162 Series. A G 129 H Grommet and nut with strain relief clamp. The clamp prevents the flexing of the wires in the immediate vicinity of he risers, so avoiding the risk of leaks. 162Series 162GB-239-XX Grommet nut with strain relief clamp only for 162 Series. A 201 Grommet and nut with right-angled strain relief clamp. The clamp prevents flexing of the wires in the immediate vicinity of the risers, so avoiding the risk of leaks 162GB Series (these are supplied to separate order 162GB-201-XX only for use with style T shells). Grommet nut with strain relief clamp only for 162 Series. 5000 75o Clamp for screened jacketed cable with grommet. Effective sealing is provided over the range of cables covered by DEF 10 (Pattern C) as specified in DEF 5325-3. These are supplied to separate order only and are intended for use with style T shells. Q G A Q B 162 Series 162GB-5000-XX--XX** * The suffix XX-XP or S enables the grommet to be matched to the insert arrangement (e.g. 12-3P). ** The suffix XX specifies the cable size. The suffix XX specifies the shell size. 18 Dimensions and Mounting Details CABLES TO DEF STAN 10 and DEF STAN 61-12 part 5 e.g. def 10-3A or DEF STAN 16-2-3A SJ CLAMPS The 162 series clamps are identical to the 62 series clamps except that the grommet is omitted. It is however, still necessary to quote the full planform because the piece parts vary to suit the appropriate cable. SJ clamps are available in 62 series only where there is an appropriate cable to DEF 10 or DEF STAN 61-12 part 5 available for the planform. 162 series availability is similar according to the planforms tooled. These are marked C on the table. PLANFORM CABLE DEF 10-etc DEF STAN 16-2 etc PLANFORM 8-3 8-3 3 C 10-2 10-6 C 12-3 C 12-10 3A,3B,3C,2B 3A,3B,3C,2B 2A,2B,2C,2Q* 6A,6B,6C,4C 3A,3B,3C,2Q* 10C 14-12 C 14-15 16-8 16-23 C 16-26 18-11 162GB-151-14-12 (no grommet supplied) Overall Length (max.) 162GB-201-XX 08 15/32 10 13/16 12 17/32 14 11/4 16 15/16 18 13/8 20 13/8 22 129/64 24 115/32 162GB-129-XX in mm 162GB-160-168 in mm 0.991 25.17 0.991 25.17 0.991 25.17 0.965 24.51 1.105 28.065 1.105 28.065 1.285 32.64 1.285 32.64 1.373 34.875 0.545 13.84 0.545 13.84 0.545 13.84 0.545 13.84 0.545 13.84 0.545 13.84 0.545 13.84 0.545 13.84 0.501 12.725 B dia. max 20-16 20-41 C 22-55 24-61 C CABLE DEF 10-etc DEF STAN 162 etc 36C 60C - - PLANFORM * Applicable to DEF10 only Type A Cables: PVC outer sheath, no overall screen, L.T. (14/.0076) unscreened cores (equivalent DEF STAN 16-2 wire size) Type B Cables: Outer screen, inner PVC sheath, L.T. (14.0076) unscreened cores (equivalent DEF STAN 16-2 wire size) Type C Cables: Outer PVC sheath, inner screen, L.T. (14.0076) unscreened cores (equivalent DEF STAN 16-2 wire size) Type Q Cables: Outer screen, inner PVC sheath, L.T. (36/.012) unscreened cores (DEF 10 only) Part Number Examples: Shell Size CABLE DEF 10 etc DEF STAN 16-2 etc 12A,12B,12C 25A,25B,25C - Straight SJ Clamps 162GB-151-XX max Length including Length including receptacle plug in mm in mm 2.732 69.39 2.742 69.64 3.152 80.06 3.152 80.06 3.272 83.10 3.272 83.10 3.696 93.87 G o 75 SJ Clamps 162GB-5000-XX max Length including Length including plug receptacle in mm in mm 2.375 60.235 2.532 64.39 2.625 66.675 2.719 69.035 2.750 69.80 3.250 82.55 3.375 85.725 2.416 61.365 2.573 65.35 2.666 67.715 2.760 70.095 2.790 70.87 3.312 84.125 3.500 88.90 J K L 2.742 69.64 2.752 69.90 3.162 80.31 3.162 80.31 3.282 83.36 3.345 84.96 3.768 95.70 Shell Size 162GB-151-XX 162GB-5000-XX in mm 162GB-129-XX in mm 162GB-214 P or S in mm All SJ Clamps in mm Cable Sleeve Int. dia. 0.005 0.127 162GB-201-XX in mm 36T 162GB-5000-XX in mm 08 0.676 17.17 0.676 17.17 0.812 20.62 0.926 23.52 1.051 26.695 1.280 32.51 1.620 41.15 0.828 21.03 0.891 22.63 1.016 25.805 1.141 28.98 1.203 30.555 1.426 36.22 1.426 36.22 1.567 39.80 1.735 44.07 0.561 14.25 0.686 17.425 0.811 20.60 0.936 23.775 1.061 26.95 1.186 30.125 1.311 33.30 1.436 36.745 1.561 39.65 0.775 19.68 0.902 22.91 1.030 26.16 1.157 29.385 1.284 32.61 1.539 39.09 1.783 45.29 0.161 4.09 0.193 4.90 0.317 8.05 0.380 9.65 0.505 12.83 0.630 16.00 0.630 16.00 0.755 19.175 0.805 20.45 0.733 18.62 0.795 20.19 0.858 21.79 0.915 23.24 1.010 25.65 1.070 27.18 1.140 28.955 1.170 29.72 1.260 32.00 1.750 44.45 1.875 47.625 2.125 53.975 2.125 53.975 2.062 52.375 2.062 52.375 2.187 55.55 10 12 14 16 18 20 22 24 19 Dust Caps TABLE OF STYLES 62GB-736 62GB-738 62GB-742 62GB-810 62GB-812 62GB-813 20 Dust Caps TABLE OF STYLES 62GB-997 62GB-998 62GB-1069 62GB-1070 21 Dust Caps TABLE OF STYLES 62GB-736 736 Caps and Chains for Single Hole Mounting Receptacles Shell Size 08 10 12 14 16 18 20 22 24 A 0.25 ( 6.35) 3.0 76.2 3.0 76.2 3.5 88.9 3.5 88.9 3.5 88.9 3.5 88.9 4.0 101.6 4.0 101.6 4.0 101.6 738 B 0.005 ( 0.13) 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.556 14.12 C dia. Max 0.734 18.64 0.859 21.82 1.000 25.4 1.125 28.57 1.250 31.75 1.375 34.92 1.500 38.1 1.625 41.27 1.750 44.45 J 0.005 ( 0.127) 0.578 14.68 0.703 17.86 0.891 22.63 1.016 25.81 1.141 29.39 1.266 32.16 1.391 35.33 1.516 38.51 1.641 41.68 62GB-738 Caps and Chains for Flange Mounting Receptacles Shell Size 08 10 12 14 16 18 20 22 24 A 0.25 ( 6.35) 3.0 76.2 3.0 76.2 3.5 88.9 3.5 88.9 3.5 88.9 3.5 88.9 4.0 101.6 4.0 101.6 4.0 101.6 B 0.005 ( 0.13) 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.556 14.12 C dia. Max 0.734 18.64 0.859 21.82 1.000 25.4 1.125 28.57 1.250 31.75 1.375 34.92 1.500 38.1 1.625 41.27 1.750 44.45 J 0.005 ( 0.127) 0.125 3.18 0.125 3.18 0.125 3.18 0.125 3.18 0.125 3.18 0.125 3.18 0.125 3.18 0.125 3.18 0.152 3.66 22 Dust Caps TABLE OF STYLES 62GB-742 742 Caps and Chains for Single Hole Mounting Receptacles Shell Size 08 10 12 14 16 18 20 22 24 A 0.25 ( 6.35) 3.0 76.2 3.0 76.2 3.5 88.9 3.5 88.9 3.5 88.9 3.5 88.9 4.0 101.6 4.0 101.6 4.0 101.6 B 0.005 ( 0.13) 0.522 13.25 0.522 13.25 0.522 13.25 0.522 13.25 0.522 13.25 0.522 13.25 0.584 14.83 0.584 14.83 0.617 15.67 C dia. Max 0.719 18.26 0.844 21.43 1.000 25.4 1.125 28.57 1.250 31.75 1.357 34.92 1.500 38.1 1.625 41.27 1.750 44.45 J 0.005 ( 0.127) 0.125 3.18 0.125 3.18 0.125 3.18 0.125 3.18 0.125 3.18 0.125 3.18 0.125 3.18 0.125 3.18 0.152 3.86 23 Dust Caps TABLE OF STYLES 62GB-810 810 BS9522-F0017-A2012 Caps and Cords for Plugs Shell Size 08 10 12 14 16 20 22 24 A 0.25 ( 6.35) 3.0 76.2 3.0 76.2 3.5 88.9 3.5 88.9 3.5 88.9 4.0 101.6 4.0 101.6 4.0 101.6 812 B 0.005 ( 0.13) 0.522 13.25 0.522 13.25 0.522 13.25 0.522 13.25 0.522 13.25 0.584 14.83 0.584 14.83 0.617 15.67 C dia. Max 0.719 18.26 0.844 21.43 1.000 25.4 1.125 28.57 1.250 31.75 1.500 38.1 1.625 41.27 1.750 44.45 J 0.005 ( 0.127) 0.145 3.68 3.685 3.68 0.145 3.68 0.145 3.68 0.145 3.68 0.145 3.68 0.145 3.68 0.171 4.34 62GB-812 BS9522-F0017-A2013 Caps and Cords for Flange Mounting Receptacles Shell Size 08 10 12 14 16 18 20 22 24 A 0.25 ( 6.35) 3.0 76.2 3.0 76.2 3.5 88.9 3.5 88.9 3.5 88.9 3.5 88.9 4.0 101.6 4.0 101.6 4.0 101.6 B 0.005 ( 0.13) 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.556 14.12 C dia. Max 0.734 18.64 0.859 21.82 1.000 25.4 1.125 28.57 1.250 31.75 1.375 34.92 1.500 38.1 1.625 41.27 1.750 44.45 J 0.005 ( 0.127) 0.145 3.68 0.145 3.68 0.145 3.68 0.145 3.68 0.145 3.68 0.145 3.68 0.145 3.68 0.145 3.68 0.171 4.34 24 Dust Caps TABLE OF STYLES 62GB-813 813 BS9522-F0017-A2014 Caps and Cords for Single Hole Mounting Receptacles Shell Size 08 10 12 14 16 18 20 22 24 A 0.25 ( 6.35) 3.0 76.2 3.0 76.2 3.5 88.9 3.5 88.9 3.5 88.9 3.5 88.9 4.0 101.6 4.0 101.6 4.0 101.6 B 0.005 ( 0.13) 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.556 14.12 C dia. Max 0.734 18.64 0.859 21.82 1.000 25.4 1.125 28.57 1.250 31.75 1.375 34.92 1.500 38.1 1.625 41.27 1.750 44.45 J 0.005 ( 0.127) 0.578 14.68 0.703 17.86 0.891 22.63 1.016 25.81 1.141 29.39 1.266 32.16 1.391 35.33 1.516 38.56 1.641 41.68 25 Dust Caps TABLE OF STYLES 997 62GB-997 Caps and Chains Ribbed for Single Hole Mounting Receptacles Shell Size 08 10 12 14 16 18 20 22 24 A 0.25 ( 6.35) 3.0 76.2 3.0 76.2 3.5 88.9 3.5 88.9 3.5 88.9 3.5 88.9 4.0 101.6 4.0 101.6 4.0 101.6 998 B 0.005 ( 0.13) 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.556 14.12 C dia. Max 0.892 22.66 1.017 26.84 1.142 29.01 1.267 32.19 1.454 36.94 1.563 39.70 1.687 42.85 1.797 45.65 1.922 48.82 J 0.005 ( 0.127) 0.578 14.69 0.703 17.86 0.891 22.64 1.016 25.81 1.141 28.99 1.266 32.16 1.391 35.34 1.516 38.51 1.641 41.69 62GB-998 Caps and Chains Ribbed for Plugs Shell Size 08 10 12 14 16 18 20 22 24 A 0.25 ( 6.35) 3.0 76.2 3.0 76.2 3.5 88.9 3.5 88.9 3.5 88.9 3.5 88.9 4.0 101.6 4.0 101.6 4.0 101.6 g max C dia. Max 0.562 14.28 0.562 14.28 0.562 14.28 0.562 14.28 0.562 14.28 0.562 14.28 0.624 15.85 0.624 15.85 0.624 15.85 0.892 22.66 1.017 25.84 1.142 29.01 1.267 32.19 1.454 36.94 1.563 39.70 1.687 42.85 1.797 45.65 1.922 48.82 J 0.005 ( 0.127) 0.124 3.18 0.124 3.18 0.124 3.18 0.124 3.18 0.124 3.18 0.124 3.18 0.124 3.18 0.124 3.18 0.147 3.74 26 Dust Caps TABLE OF STYLES 62GB-1069 1069 Caps and Cords Ribbed for Single Hole Mounting Receptacles Shell Size 08 10 12 14 16 18 20 22 24 A 0.25 ( 6.35) 3.0 76.2 3.0 76.2 3.5 88.9 3.5 88.9 3.5 88.9 3.5 88.9 4.0 101.6 4.0 101.6 4.0 101.6 B 0.005 ( 0.13) 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.556 14.12 C dia. Max 0.892 22.66 1.017 26.84 1.142 29.01 1.267 32.19 1.454 36.94 1.563 39.70 1.687 42.85 1.797 45.65 1.922 48.82 J 0.010 ( 0.25) 0.578 14.69 0.703 17.86 0.891 22.64 1.016 25.81 1.141 28.99 1.266 32.16 1.391 35.34 1.516 38.51 1.641 41.696 62GB-1070 1070 Caps and Cords Ribbed for Flange Mounting Receptacles Shell Size 08 10 12 14 16 18 20 22 24 A 0.25 ( 6.35) 3.0 76.2 3.0 76.2 3.5 88.9 3.5 88.9 3.5 88.9 3.5 88.9 4.0 101.6 4.0 101.6 4.0 101.6 B 0.005 ( 0.13) 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.521 13.23 0.556 14.12 C dia. Max 0.892 22.66 1.017 22.66 1.142 29.01 1.267 32.19 1.454 36.94 1.563 39.70 1.687 42.85 1.797 45.65 1.922 48.82 J 0.005 ( 0.127) 0.117 3.03 0.119 3.03 0.119 3.03 0.119 3.03 0.119 3.03 0.119 3.03 0.110 3.03 0.119 3.03 0.147 3.74 27 Interconnection Accessories 5001 BACKSHELL SERIES * For use on 162GB connector styles * The 5001 Backshells are suitable for termination using Bandit, Zetalock and Heatshrink product * The 5001 Backshell is designed to give 360o screening Part Numbering Information AIA50 01 XX XX XX XX XX XX Denotes Backshell Style 50 - Zeta Lock Termination with Heatshrink Boot Groove 51 - Spin Coupler to take Heatshrink Boot Denotes Connector Style 01 - Series 2 162GB Denotes Connector Shell Size 8, 10, 12, 14, 16, 18, 20, 22, 24 Denotes Backshell Inlet Size See Chart for Inlet Standard Consult Factory for alternatives Denotes Backshell Exit Angle 00 = 0o 45 - 45o o 90 - 90 Consult Factory for alternatives Denotes Working Length 10 - Standard Consult Factory for alternatives Denotes Backshell Material AA - Aluminium Alloy RB - Aluminium Bronze SS - Stainless Steel Denotes Backshell Plating Finish 01 - Unplated 02 - Electroless Nickel 03 - Cadmium with Olive Drab Chromate Passivation 04 - Zinc Cobalt with Green Chromate Passivation 05 - Zinc Cobalt with Black Chromate Passivation 28 Interconnection Accessories 5001 BACKSHELL SERIES - STRAIGHT 36.35 MAX OH MAX OG MAX A THREAD OB MAX 29.95 MAX Rec Hellerman Boot 90o Rec Hellerman Boot Straight Spring Ref 14.04 1152-4-GW24 152-42-GW24 HE 050 8.05 15.61 1154-4-GW24 154-42-GW24 HE 100 24.64 11.25 18.81 1155-4-GW24 155-42-GW24 HE 100 13/16-20 UNEF 29.13 12.83 20.39 1155-4-GW24 155-42-GW24 HE 200 5001-16-00-00-10-AA-XX 15/16-20 UNEF 32.13 16.00 23.57 1156-4-GW24 155-42-GW24 HE 200 5001-18-00-00-10-AA-XX 1 1/16-18 UNEF 32.64 19.18 26.74 1156-4-GW24 156-42-GW24 HE 300 5001-20-00-00-10-AA-XX 1 3/16-18 UNEF 39.78 22.38 29.92 1157-4-GW24 157-43-GW24 HE 300 5001-22-00-00-10-AA-XX 1 5/16-18 UNEF 43.28 25.55 33.09 1157-4-GW24 157-43-GW24 HE 300 5001-24-00-00-10-AA-XX 1 7/16-18 UNEF 44.25 25.55 33.09 1157-4-GW24 157-43-GW24 HE 300 5001-08-06-00-10-AA-XX 7/16-28 UNEF 18.14 4.83 14.04 1152-4-GW24 152-42-GW24 HE 050 5001-10-08-00-10-AA-XX 9/16-24 UNEF 20.45 6.48 14.04 1154-4-GW24 154-42-GW24 HE 050 5001-12-10-00-10-AA-XX 11/16-24 UNEF 24.64 8.05 15.61 1155-4-GW24 155-42-GW24 HE 100 5001-14-12-00-10-AA-XX 13/16-20 UNEF 29.13 11.25 18.81 1155-4-GW24 155-42-GW24 HE 100 5001-16-14-00-10-AA-XX 15/16-20 UNEF 32.13 12.83 20.39 1156-4-GW24 156-42-GW24 HE 200 5001-18-16-00-10-AA-XX 1 1/16-18 UNEF 32.64 16.00 23.57 1156-4-GW24 156-42-GW24 HE 200 5001-20-18-00-10-AA-XX 1 3/16-18 UNEF 39.78 19.18 26.74 1157-4-GW24 157-43-GW24 HE 300 5001-22-20-00-10-AA-XX 1 5/16-18 UNEF 43.28 22.38 29.92 1157-4-GW24 157-43-GW24 HE 300 5001-24-22-00-10-AA-XX 1 7/16-18 UNEF 44.25 25.55 33.09 1157-4-GW24 157-43-GW24 HE 300 Part Number A-Thread OB MAX OG MAX OH MAX 5001-08-00-00-10-AA-XX 7/16-28 UNEF 18.14 6.48 5001-10-00-00-10-AA-XX 9/16-24 UNEF 20.45 5001-12-00-00-10-AA-XX 11/16-24 UNEF 5001-14-00-00-10-AA-XX All dimensions in mm 29 Interconnection Accessories 5001 BACKSHELL SERIES - RIGHT ANGLE J MAX D MAX A THREAD OB THREAD E MAX 17.98 MAX OG MAX OH MAX Part Number A-Thread D MAX OB MAX E MAX OG MAX OH MAX J MAX Rec Hellerman Boot Straight Spring Ref 5001-08-00-90-AA-XX 7/16-28 UNEF 35.18 18.14 25.98 6.48 14.04 32.39 152-42-GW24 HE 050 5001-10-00-90-AA-XX 9/16-24 UNEF 38.35 20.45 29.16 8.05 15.61 35.56 154-42-GW24 HE 100 5001-12-00-90-AA-XX 11/16-24 UNEF 39.75 24.64 32.33 11.25 18.81 38.74 155-42-GW24 HE 100 5001-14-00-90-AA-XX 13/16-20 UNEF 46.30 29.13 37.11 12.83 20.39 43.51 155-42-GW24 HE 200 5001-16-00-90-AA-XX 15/16-20 UNEF 47.70 32.13 40.28 16.00 23.57 46.69 156-42-GW24 HE 200 5001-18-00-90-AA-XX 1 1/16-18 UNEF 47.70 32.64 40.28 19.18 26.74 46.69 156-42-GW24 HE 300 5001-20-00-90-AA-XX 1 3/16-18 UNEF 55.63 39.78 48.21 22.38 29.92 54.61 157-43-GW24 HE 300 5001-22-00-90-AA-XX 1 5/16-18 UNEF 58.80 43.28 51.38 25.55 33.09 57.79 157-43-GW24 HE 300 5001-24-00-90-AA-XX 1 7/16-18 UNEF 58.80 44.25 51.38 25.55 33.09 57.79 157-43-GW24 HE 300 5001-08-06-90-AA-XX 7/16-28 UNEF 33.40 18.14 25.98 4.83 14.04 32.39 152-42-GW24 HE 050 5001-10-08-90-AA-XX 9/16-24 UNEF 36.58 20.45 29.16 6.48 14.04 35.56 154-42-GW24 HE 050 5001-12-10-90-AA-XX 11/16-24 UNEF 39.75 24.64 32.33 8.05 15.61 38.74 155-42-GW24 HE 100 5001-14-12-90-AA-XX 13/16-20 UNEF 44.53 29.13 37.11 11.25 18.81 43.51 155-42-GW24 HE 100 5001-16-14-90-AA-XX 15/16-20 UNEF 47.70 32.13 40.28 12.83 20.39 46.69 156-42-GW24 HE 200 5001-18-16-90-AA-XX 1 1/16-18 UNEF 47.70 32.64 40.28 16.00 23.57 46.69 156-42-GW24 HE 200 5001-20-18-90-AA-XX 1 3/16-18 UNEF 55.63 39.78 48.21 19.18 26.74 54.61 157-43-GW24 HE 300 5001-22-20-90-AA-XX 1 5/16-18 UNEF 58.80 43.28 51.38 22.38 29.92 57.79 157-43-GW24 HE 300 5001-24-22-90-AA-XX 1 7/16-18 UNEF 58.80 44.25 51.38 25.55 33.09 57.79 157-43-GW24 HE 300 All dimensions in mm 30 Interconnection Accessories INSTALLATION - PROCEDURE * Prepare the cable making sure that a sufficient length of shield is available, so that it fits against the front shoulder of the lip groove. * Before insertion of connector contacts, slide the heat-shrinkable connector boot onto the cable followed by the Spring Adapter. * Position the heatshrinkable boot, Spring Adapter, and shield braid out of the way and insert the connector contacts. Depending upon the shielding braid size, it can either be folded back onto itself or bunched up concertina style out of the way for easy access to the cable conductors. * Screw the Spring Adapter onto the connector and tighten to the torque value specified by the connector manufacturer. Typical torque values are shown in table on Page 7. It is recommended that the connector threads are lubricated with a suitable compound if a liquid thread lock is not used. The adapter should be hand tightened to ensure proper thread alignment and then tightened with a strap wrench and torque meter to the specified torque. * Bring the cable shield braid up onto the adapter body so that it fits against the front shoulder of the lip groove. Alternatively extend the braid past the lip groove. Secure Cable Braid End with Tape NOTE: After assembly, braid can be trimmed with side cutters or folded back and secured with high temperature tape * Fold Cable Braid back Open up the constant force spring and wrap it around the cable braid section that is positioned over the constant force spring slot area of the adapter. This is most easily accomplished by lifting up the end of the spring and trapping the braid covered adapter between the spring coil and raised end. The spring will now stay in place and can be installed by simply rolling the coil around the braid covered adapter. Refer to appropriate code of practice for procedure to install heatshrink shape. Roll Spring Coil around Adapter Lift Up End of Spring Trap Braid Covered Adapter between Spring Coil and raised end 31 Interconnection Accessories INSTALLATION - PROCEDURE Re-Entry Procedure * Reheat the heatshrink shape, remove to expose the ZetalokTM?spring and braid. * Once spring is exposed, lift up the edge of the ZetalokTM spring and push it around the circumference of the assembly to form a coil which can then be rolled around the assembly to remove the spring. * Lift the cable screen braid off the backshell and push it back out of the way. * Unscrew the backshell and push it back out to facilitate repairs at the connector or exposed connector area. * Follow the practice detailed in these instructions to re-install the ZetalokTM spring backshell Note: The ZetalokTM?spring can be installed and removed an infinite number of times if not bent or distorted in any way during the removal process. 32 Interconnection Accessories SHIELD TERMINATION ASSEMBLY PROCESS 1. Prepare Cable Braid for termination process (Figure 1) Adapter Retention Lip Conductors Braid 2. Push Braid forward over Adapter Retention Lip to the Adapter Incline Point (or .4" [10.2mm] minimum braid length). Milk Braid as required to remove slack and ensure a snug fit around the shield termination area (Figure 2). .400 (1.2mm) Minimum Length Braid over Termination area Adapter Incline 3. Prepare the Band in the following manner: IMPORTANT: Due to Connector/ Adapter circumference, it may be necessary to prepare the Band around the Cable or Retention Area. Buckle Tail Length Indicator Mark a) Roll Band through the Buckle Slot twice (Bands must be double-coiled). b) Pull on Band until Mark (E) is within approximately (.250 inch (6.4mm) of Buckle Slot (Figure 3). The Band may be tightened further if desired. NOTE: Prepared Band should have (E) Mark visible approximately where shown in Figure 3. SHIELD TERMINATION CLAMPING PROCESS (Figures 4 through 8): NOTE: To free Tool Handles, move Holding Clips to centre of Tool. 4. Squeeze Gripper Release Lever and insert Band into the front end opening of the Tool. (NOTE: Circular portion of looped band must always be face downward). 5. Aligning the Band and Tool with the Shield Termination Area, squeeze Black Pull-Up Handle repeatedly using short strokes until it locks against the Tool Body. (This indicates the Band is compressed to the Tool Precalibrated Tension). NOTE: If alignment of band and shield is unsatisfactory, tension on band can be relaxed by pushing on slotted release lever on top of tool. Make adjustments as necessary and again squeeze black pull-up handle. 6. Complete the Clamping Process by squeezing the Grey Cut-Off Handle. 7. Remove excess Band from Tool. 8. Inspect Shield Termination. 33 Key/Keyway Orientations FOR Patt. 105 DEF STAN 59-35 (Part 1) Sec. 3 3 Pins spaced 120o apart Datum is always taken from major key or keyway. In receptacles the major keyway always remains fixed in relation to the mounting flange. For the A*, B, C, D*, E and F orientations, the three bayonet locations and associated minor keyways are rotated complete, in accordance with the table below. N.B. The accompanying diagram shows a receptacle shell, with keyways. Corresponding key orientations for a mating plug shell are therefore always clockwise. Shell Size Values for a(degrees) N A* B C Values for (degrees) Values for ? (degrees) D* E F N A* B C D* E F N A* B C D* E F 8 105 92 - - 118 118 82 35 35 - - 35 30 50 75 75* - - 75 100 75 10 105 95 85 125 115 115 85 35 35 35 35 35 30 50 75 75 75 75 75 100 75 12 105 97 89 121 113 115 85 35 35 35 35 35 30 50 75 75 75 75 75 100 75 14 105 98 91 119 112 75 120 35 35 35 35 35 30 50 75 75 75 75 75 100 75 16 105 99 93 117 111 75 120 35 35 35 35 35 30 50 75 75 75 75 75 100 75 18 105 100 95 115 110 75 120 35 35 35 35 35 30 50 75 75 75 75 75 100 75 20 105 100 95 115 110 75 120 35 35 35 35 35 30 50 75 75 75 75 75 100 75 22 105 101 97 113 109 75 120 35 35 35 35 35 30 50 75 75 75 75 75 100 75 24 105 101 97 113 109 75 120 35 35 35 35 35 30 50 75 75 75 75 75 100 75 Values for ? (degrees) Orientation Values for f (degrees) Orientation Shell Size N A* B C D* E F N A* B C D* E F 8 50 50 - - 50 30 45 60 47 - - 73 73 47 10 50 50 50 50 50 30 45 60 50 40 80 70 70 50 12 50 50 50 50 50 30 45 60 52 44 76 68 70 50 14 50 50 50 50 50 30 35 60 53 46 74 67 30 75 16 50 50 50 50 50 30 35 60 54 48 72 66 30 75 18 50 50 50 50 50 30 35 60 55 50 70 65 30 75 20 50 50 50 50 50 30 35 60 55 50 70 65 30 75 22 50 50 50 50 50 30 35 60 56 52 68 64 30 75 24 50 50 50 50 50 30 35 60 56 52 68 64 30 75 * now inactive for new designs against Pattern 105 but available for replacement purposes. Superseded in DEF STAN 59-35 (Part 1) Sec. 3. by orientations E and F. 34 Insert Orientations FOR MIL-C-26482 AND REPLACEMENT PURPOSES IN Patt. 105 OF DEF STAN 59-35 (Part 1) Sec. 3 Normal Position with Pin Contacts Alternative Position of Insert with Socket Contacts (O counterclockwise) Alternate Position of Insert with Pin Contacts (O clockwise) Each diagram shows mating face of insert Insert Arrangement Normal Orientation 0 (degrees) W X Y Z 8-3 0 60 210 - - 8-33 0 90 - - - 8-98 0 - - - - 10-2 0 - - - - 10-6 0 90 - - - 10-7 0 - - - - 12-3 0 - - 180 - 12-10 0 60 155 270 295 14-5 0 40 92 184 273 14-12 0 43 90 - - 14-19 0 30 165 315 - 16-8 0 54 152 180 331 16-23 0 158 270 - - 16-26 0 60 - 275 338 18-11 0 62 119 241 340 18-32 0 85 138 222 265 20-41 0 45 126 225 - 22-21 0 16 135 175 349 22-55 0 30 142 226 314 24-61 0 90 180 270 324 35 Assembly Instructions FOR AMPHENOL STRAIGHT S.J. CLAMPS TO DEF STAN 59-35 (Part 1) Sec. 3 FOR INTERNALLY AND EXTERNALLY SCREENED AND UNSCREENED CABLES INTERNALLY SCREENED JACKETED CABLE TYPE C Cable and Wire Stripping Strip the outer P.V.C. Jacket of the cable back to dim `A' to expose the internal braid. Trim the braid back to within 19.05mm (0.75 in) of P.V.C. jacket and fold back `B' Size 08 10 12 & 14 16 & 20 24 A Dimension mm in 34.93 36.51 41.27 44.45 49.21 1.375 1.437 1.625 1.750 1.937 FOR 162 SERIES Strip 5.6mm (0.220 in) to 6.6mm (0.260 in) of insulation from each wire taking care not to cut or nick strands. If ends fray twist them back to their original lay. INITIAL ASSEMBLY Slide onto the cable the following items in this order (1) Nut (2) Washer (3) Gasket (4) Braid Clamp and (5) Clamp Body CRIMP CONNECTION TO CONTACTS (162 SERIES) Using the recommended tools, crimp the contacts to the wires and insert them in the connector as described in the Amform instructions, which are supplied with each 162 series assembly. Bring up clamp body taking care not to drag the braid forward. (If necessary a small amount of thin tape may be used to hold the braid in position whilst carrying out this operation). Screw the clamp body onto the connector accessory thread, making sure that the connector serrations engage with those on clamp body. Fold the braid out at right angles to the cable and slide forward the braid clamp. Smooth back braid onto the braid clamp and trim off the surplus. Slide up gasket, washer, screw on nut and tighten. Surplus Braid Trimmed 36 Assembly Instructions FOR AMPHENOL STRAIGHT S.J. CLAMPS TO DEF STAN 59-35 (Part 1) Sec. 3 FOR INTERNALLY AND EXTERNALLY SCREENED AND UNSCREENED CABLES EXTERNALLY SCREENED JACKETED CABLE TYPES `B & Q' Cable and Wire Stripping Strip the outer braid and internal P.V.C. jacket of the cable back to dim `A' Size 08 10 12 & 14 16 & 20 24 A Dimension mm in 33.32 34.93 39.70 42.85 47.63 1.312 1.375 1.563 1.687 1.875 FOR 162 SERIES Strip 5.6mm (0.220 in) to 6.6mm (0.260 in) of insulation from each wire taking care not to cut or nick strands. If ends fray twist them back to their original lay. INITIAL ASSEMBLY Slide onto the cable the following items in this order (1) Nut (2) Washer (3) Male Braid Clamp Convolute Screen (See B) as far as possible, and slide on times (4) Female Braid Clamp (5) Gasket and (6) Clamp Body CRIMP CONNECTION TO CONTACTS (162 SERIES) Using the recommended tools, crimp the contacts to the wires and insert them in the connector as described in the Amform instructions, which are supplied with each 162 series assembly. Bring up clamp body and screw onto the connector accessory thread, making sure that the connector serrations engage with those on clamp body. Slide forward gasket and female braid clamp. Push forward screen and fold out at right angles braid which does not return to original position. Slide up male braid clamp. Smooth back braid onto male braid clamp and trim off surplus. Slide up washer. Screw on nut and tighten. Surplus Braid Trimmed UNSCREENED JACKETED CABLES TYPE `A' All procedures concerning this type of cable to be as for internally screened jacketed cable but all references to screen (Braid) to be disregarded. 37 Assembly Instructions FOR AMPHENOL ANGLED S.J. CLAMPS TO DEF STAN 59-35 (Part 1) Sec. 3 FOR INTERNALLY AND EXTERNALLY SCREENED AND UNSCREENED CABLES INTERNALLY SCREENED JACKETED CABLE TYPE `C' Cable and Wire Stripping Strip the outer P.V.C. jacket of the cable back to dim `A' to expose the internal braid. Trim the braid back to within 19.05mm (0.75 in) of P.V.C. jacket and fold back `B'. Size 08 10/12 & 14 16 20 24 A Dimension mm in 58.15 66.68 69.85 88.90 95.25 2.890 2.625 2.750 3.500 3.750 FOR 162 SERIES Strip 5.6mm (0.220 in) to 6.6mm (0.260 in) of insulation from each wire taking care not to cut or nick strands. If ends fray twist them back to their original lay. INITIAL ASSEMBLY Slide onto the cable the following items in this order (1) Nut (2) Washer (3) Gasket (4) Braid Clamp (5) 75o Angled Body CRIMP CONNECTION TO CONTACTS (162 SERIES) Using the recommended tools, crimp the contacts to the wires and insert them in the connector as described in the Amform instructions, which are supplied with each 162 series assembly. Bring up clamp body taking care not to drag the braid forward. (If necessary a small amount of thin tape may be used to hold the braid in position whilst carrying out this operation). Screw the clamp body onto the connector accessory thread, making sure that the connector serrations engage with those on the clamp body. Fold the braid out at right angles to the cable and slide forward the braid clamp. Smooth back braid onto the braid clamp and trim off the surplus. Slide up gasket, washer, screw on nut and tighten. Surplus Braid Trimmed 38 Assembly Instructions FOFOR AMPHENOL ANGLED S.J. CLAMPS TO DEF STAN 59-35 (Part 1) Sec. 3 FOR INTERNALLY AND EXTERNALLY SCREENED AND UNSCREENED CABLES EXTERNALLY SCREENED JACKETED CABLES TYPES `B' & `Q' Cable and Wire Stripping Strip the outer braid and internal P.V.C. jacket of the cable back to dim `A'. Size 08 10, 12 & 14 16 20 24 A Dimension mm in 58.15 66.68 69.85 88.90 95.25 2.890 2.625 2.750 3.500 3.750 FOR 162 SERIES Strip 5.6mm (0.220 in) to 6.6mm (0.260 in) of insulation from each wire taking care not to cut or nick strands. If ends fray twist them back to their original lay. INITIAL ASSEMBLY Slide onto the cable the following items in this order: (1) Nut (2) Washer (3) Male Braid Clamp - Convolute Screen (See B) as far as possible and slide on items (4) Female Braid Clamp (5) Gasket (6) 75o Right Angled Body CRIMP CONNECTION TO CONTACTS (162 SERIES) Surplus Braid Using the recommended tools, crimp the contacts to the wires and insert Trimmed them in the connector as described in the Amform instructions, which are supplied with each 162 series assembly. Bring up clamp body taking care not to drag the braid forward. (If necessary a small amount of thin tape may be used to hold the braid in position whilst carrying out this operation). Screw the clamp body onto the connector accessory thread, making sure that the connector serrations engage with those on the clamp body. Fold the braid out at right angles to the cable and slide forward the braid clamp. Smooth back braid onto the braid clamp and trim off the surplus. Slide up gasket, washer, screw on nut and tighten. UNSCREENED JACKETED CABLES `TYPE A' All procedures concerning this type of cable to be as for internally screened jacketed cable but all references to screen (Braid) to be disregarded. 39 162GB Assembly Instructions WIRE STRIPPING - 162GB SERIES Strip 5.6mm (.220 in) to 6.6mm (.260 in) of insulation from end of wire for both size 20 and 16 contacts taking care not to cut or nick strands. If ends fray twist them back to their original lay. CONTACT AND WIRE DATA - 162GB SERIES Stripping Lengths A.W.G. in mm Permissible Insulation O.D. range for Grommet Sealing Pin: 162GB-149-20000-05 Skt: 162GB-101-20000-05 20, 22, 24 0.032 - 0.020 0.81-0.51 0.047 - 0.085 1.19 - 2.16 0.220-0.260 5.6 - 6.6 Pin: 162GB-149-16000-05 Skt: 162GB-101-16000-05 16, 18, 20 0.051 - 0.032 1.295 - 0.81 0.066 - 0.109 1.675 - 2.77 0.220 - 0.260 5.6 - 6.6 Suitable Wire Sizes Contact Size Colour Code Contact Part Nos 20 RED 16 BLUE CRIMP WIRE CONTACTS in mm CRIMPING JAW SETTING Use Amphenol 294-542 Crimp Tool (M22520/1-01) with 294-188901 Turret Head (M22520/1-02). Release and rotate Turret Knob to proper contact size (as per colour code) and lock adjust Selector Knob on handle to correct wire size [see table]. Insert stripped wire into Contact Pocket until it is visible through inspection hole. Fully seat Contact in Crimp Tool Positioner and close handles in one full stroke. (The Ratchet will not release until tool has completed full stroke). Inspect Crimp for wire visibility through Inspection Hole. Contact Size Wire Size Crimp Jaw Setting 24 22 20 No. 2 No.3 No.4 20 18 16 No. 4 No. 5 No. 6 20 16 INSPECTION HOLE CRIMPING WIRE TO CONTACT CONTACT INSERTION Select the proper insertion tool for the size of contact Table 1. The Insertion Tool and procedure are the same for both pin and socket contacts. Slide rear accessory and sleeve over wire bundle. Lay wire in groove of insertion tool and slide contact into front of tool until it is properly located in tool probe. Insert contact into the correct hole in the rear face of the grommet. Keeping contact in line with the axis of the hole, apply a smooth even push on the tool until the contact is fully seated in position. Note: it is essential that the contact and tool are correctly aligned with the axis of hole during insertion to prevent damage to contacts. Withdraw tool at right angles to grommet surface until complete free of connector. All contacts must be inserted whether in circuit or not and the appropriate size sealing plug used behind any contacts that are not wired. Push the sealing plug in by hand until it is fully seated. TABLE 1 Contact Colour Size Code Insertion Tool Part No. Amphenol M.S. Grommet Sealing Plug 20 RED 294GB-5000-20 - 162GB-130-20000 16 BLUE 294-96 MS 24256A-16 162GB-130-16000 40 CONTACT INSERTION Contact Size TABLE 2 CAUTION: extra care is required in this operation to prevent damage to the connector. Remove the rear accessory and sleeve and slide back on wire bundle. Select the proper removal tool for the size of contact from table 2. The same tool is used for both pin and socket contacts. Position the removal tool over the contacts to be removed and push until tool probe is fully bottomed, shown when indicator band enters insert hole. Tool is inserted to first band only when removing pin contacts and to the second band for socket contact removal. Slide the plunger know forward to remove contact. Contact Size Colour Code 20 16 Removal Tool Part Number Amphenol M.S. RED 294-89 MS 24256R-20 BLUE 294-97 MS 25246R-16 Details of operator training are available from Amphenol upon request. Indicator Band CONTACT REMOVAL Notice: Products are sold subject to Amphenol's conditions of sale ("the standard conditions"). All specifications and statements contained herein are believed to be correct at the time of printing but no representation or warranty, express or implied, is given as to any specification or statement contained herein. Product specifications including performance characteristics are typical only and subject to deviation. Specifications are also subject to change without notice. Users should not assume that all safety measures are indicated or that other measures may not be required. No representation or warranty, express or implied, is given that any use of products (including any stated or suggested use) does not infringe any patent, registered design or other third party rights and no stated or suggested use of products can be taken to recommend any such infringement. Amphenol Thanet Way, Whitstable, Kent. CT5 3JF Tel: 01227 773200 Fax: 01227 276571 41