Mechanical dimensions and general specifications are listed below:
Note 1)
The maximum optical output power is 3mW. Each module is
tested at the factory, the beam is collimated and the optical output set
between 0.95mW and 1mW with an input voltage of +3.0 volts.The
optical power may be adjusted by the user; however, a maximum
optical output of 3mW must not be exceeded an optical power
meter is required to accurately set the optical output. Exceeding the
3mW limit will severely shorten the diodes lifetime and/or may cause
immediate failure.
Note 2)
The optimum input voltage is +3.0 volts; however, the
modules will operate over a range from +3.0 to 5.0 volts. Using an
input voltage greater than 3 volts results in excess heat which must be
dissipated by the module. For best results when operating at increased
input voltage or at elevated ambient temperatures, the module should
be mounted using a metal mounting bracket or clamp to increase the
thermal mass and facilitate heat transfer. In any case, the module
should not be mounted in a plastic structure which inhibits heat transfer.
Note 3)
The optical output power is directly related to the input voltage.
If the input power is increased, the optical output will increase.
Therefore using an optical power meter, the optical power must be set
with the module operating at the highest anticipated input voltage. For
operation at a constant output level, the supply voltage should be
regulated.If desired, the optical output may be controlled externally by
varying the input or supply voltage.
Note 4)
Diode dependent specification values will vary from one
diode module to another.
Note 5)
The collimated beam is measured at the 1/e2 point. The first
number (smaller value) is the laser diodes parallel axis while the
second number is the perpendicular axis. The values listed are typical
and may vary from diode to diode.
Note 6)
The focused beam is measured at the 1/e2 point. This
measurement is taken at the minimum focus distance as listed in the
table above the distance is measured from the front of the module
housing to the focused spot. The first number (smaller value) is the
laser diodes perpendicular axis while the second number is the parallel
axis. The values listed are typical and may vary from diode to diode.
Important notes regarding Laser Safety and CDRH Classifications:
Optima Diode Laser Modules, DLM 2100 Series and DLM 2300 Series
are sold solely as components for O.E.M. use. The modules do not
include a laser emission indicator, safety shutter, or other features
required for a certified laser system. Therefore, these units do not meet
CDRH safety requirements and are not CDRH listed or certified. It is the
purchasers responsibility to meet applicable federal regulations
contained in Title 21 CFR parts 1000 and 1040.10 chapter 1,
subchapter Radiological Health.
Revised 01JAN01
© Optima Precision Inc. Phone: (503) 638-2525 email: sales@optima-optics.com url: http://www.optima-optics.com
BASIC SERIES NUMBER DLM 2100 Series DLM 2300 Series
Module Part Number DLM 2103-636 DLM 2103-650 DLM 2303-636 DLM 2303-650
Unit Price (Qty 1-24 pcs.) $54.00 $35.50 $63.00 $43.80
OPTICAL CHARACTERISTICS
Optical Output Power 3mW (please read notes 1&3 below)
Typical Wavelength 635nm 650nm 635nm 650nm
Collimating Lens Plastic Asphere
Optima P/N 300-0360-780 Glass Asphere
Optima P/N 305-0065-780
Collimated Beam Size (note 5) 1.02mm x 2.94mm 0.91mm x 3.02mm 1.37mm x 3.37mm 1.26mm x 3.37mm
Focused Beam Size (note 6) ~10 x 25 microns ~18 x 28 microns ~15 x 28 microns ~17 x 30 microns
Minimum Focus Distance 18mm 18mm 40mm 40mm
ELECTRICAL AND MECHANICAL CHARACTERISTICS
Input Voltage +3.0 to 5.0 volts DC, +3 volts DC recommended (note 2)
Input Current 60mA typical for 635nm module (note 4)
40mA typical for 650nm module (note 4)
Operating Mode Automatic Power Control (APC) Continuous-wave (CW)
Operating Temperature 10ºC ~ +50ºC for 635nm module (note 4)
10ºC ~ +60ºC for 650nm module (note 4)
Storage Temperature 40ºC ~ +80ºC (note 4)
Mechanical Dimensions
(diameter x length) Diode Housing Ø10mm x 12.5mm (Ø.394 inches x 0.49 inches)
Overall length including PCB 21.5mm (0.85 inches), wire leads 75mm (3 inches)