LT1683 Slew Rate Controlled Ultralow Noise Push-Pull DC/DC Controller DESCRIPTION FEATURES n n n n n n n n n Greatly Reduced Conducted and Radiated EMI Low Switching Harmonic Content Independent Control of Output Switch Voltage and Current Slew Rates Greatly Reduced Need for External Filters Dual N-Channel MOSFET Drivers 20kHz to 250kHz Oscillator Frequency Easily Synchronized to External Clock Regulates Positive and Negative Voltages Easier Layout Than with Conventional Switchers The LT (R)1683 is a switching regulator controller designed to lower conducted and radiated electromagnetic interference (EMI). Ultralow noise and EMI are achieved by controlling the voltage and current slew rates of external N-channel MOSFET switches. Current and voltage slew rates can be independently set to optimize harmonic content of the switching waveforms vs efficiency. The LT1683 can reduce high frequency harmonic power by as much as 40dB with only minor losses in efficiency. The LT1683 utilizes a dual output (push-pull) current mode architecture optimized for low noise topologies. The IC includes gate drivers and all necessary oscillator, control and protection circuitry. Unique error amp circuitry can regulate both positive and negative voltages. The oscillator may be synchronized to an external clock for more accurate placement of switching harmonics. APPLICATIONS n n n n n n Power Supplies for Noise Sensitive Communication Equipment EMI Compliant Offline Power Supplies Precision Instrumentation Systems Isolated Supplies for Industrial Automation Medical Instruments Data Acquisition Systems Protection features include gate drive lockout for low VIN, opposite gate lockout, soft-start, output current limit, short-circuit current limiting, gate drive overvoltage clamp and input supply undervoltage lockout. L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and DirectSense is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. TYPICAL APPLICATION Ultralow Noise 48V to 5V DC/DC Converter 48V 510 0.5W 51k 39F 63V MIDCOM 31244 FZT853 10F 20V 1N4148 23.2k 14 5 976 6 1.2nF 7 16.9k 8 25k 3.3k 16 25k 3.3k 15 1.5k 12 CAP A V5 GATE A SYNC CT CAP B LT1683 RT GATE B RVSL CS RCSL PGND VC SS 13 GND 11 FB NFB 10 22H 150F OS-CON 17 3 VIN GCL SHDN 0.22F 22nF MBRS340 8.2V 68F 20V 11V OPTIONAL MBR0530 2N3904 2 5pF 22H A 5V/2A 2x100F POSCAP 5V Output Noise (Bandwidth = 100MHz) 10pF 200V MBRS340 1 18 B 200VP-P 30pF 19 4 Si9422 A 200V/DIV 10pF 200V 5pF B 20mV/DIV Si9422 0.1 20 7.50k 9 5s/DIV 30pF 1683 TA01a 2.49k 10nF 1683 TA01 1683fd 1 LT1683 ABSOLUTE MAXIMUM RATINGS PIN CONFIGURATION (Note 1) TOP VIEW Supply Voltage (VIN)..................................................20V Gate Drive Current...................................... Internal Limit V5 Current................................................... Internal Limit SHDN Pin Voltage......................................................20V Feedback Pin Voltage (Trans. 10ms) ....................... 10V Feedback Pin Current .............................................10mA Negative Feedback Pin Voltage (Trans. 10ms) .......... 10V CS Pin............................................................................5V GCL Pin........................................................................16V SS Pin............................................................................3V Operating Junction Temperature Range (Note 3)...................................................- 40C to 125C Storage Temperature Range....................-65C to 150C Lead Temperature (Soldering, 10 sec)................... 300C GATE A 1 20 PGND CAP A 2 19 GATE B GCL 3 18 CAP B CS 4 17 VIN V5 5 16 RVSL SYNC 6 15 RCSL CT 7 14 SHDN RT 8 13 SS FB 9 12 VC NFB 10 11 GND G PACKAGE 20-LEAD PLASTIC SSOP TJMAX = 150C, JA = 110C/ W ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LT1683EG#PBF LT1683EG#TRPBF 1683 20-Lead Plastic SSOP - 40C to 125C LT1683IG#PBF LT1683IG#TRPBF 1683 20-Lead Plastic SSOP - 40C to 125C LEAD BASED FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LT1683EG LT1683EG#TR 1683 20-Lead Plastic SSOP - 40C to 125C LT1683IG LT1683IG#TR 1683 20-Lead Plastic SSOP - 40C to 125C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ This product is only offered in trays. For more information go to: http://www.linear.com/packaging/ ELECTRICAL CHARACTERISTICS The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VIN = 12V, VC = 0.9V, VFB = VREF , RVSL, RCSL = 16.9k, RT = 16.9k and other pins open unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS 1.235 V Error Amplifiers VREF Reference Voltage Measured at Feedback Pin l 1.250 1.265 250 1000 nA 0.012 0.03 %/V - 2.500 - 2.45 V 0.009 0.03 %/V 1500 2200 2500 mho mho IFB Feedback Input Current VFB = VREF l FBREG Reference Voltage Line Regulation 2.7V VIN 20V l VNFR Negative Feedback Reference Voltage Measured at Negative Feedback Pin with Feedback Pin Open l INFR Negative Feedback Input Current VNFB = VNFR NFBREG Negative Feedback Reference Voltage Line Regulation 2.7V VIN 20V gm Error Amplifier Transconductance IC = 50A - 2.56 - 37 l l 1100 700 - 25 A 1683fd 2 LT1683 ELECTRICAL CHARACTERISTICS The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VIN = 12V, VC = 0.9V, VFB = VREF , RVSL, RCSL = 16.9k, RT = 16.9k and other pins open unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS IESK Error Amp Sink Current VFB = VREF + 150mV, VC = 0.9V l 120 200 350 A IESRC Error Amp Source Current VFB = VREF - 150mV, VC = 0.9V l 120 200 350 A VCLH Error Amp Clamp Voltage High Clamp, VFB = 1V 1.27 V VCLL Error Amp Clamp Voltage Low Clamp, VFB = 1.5V 0.12 V AV Error Amplifier Voltage Gain 250 V/V FBOV FB Overvoltage Shutdown Outputs Drivers Disabled 1.47 V ISS Soft-Start Charge Current VSS = 1V 9.0 180 12 A Oscillator and Sync fMAX Max Switch Frequency fSYNC Synchronization Frequency Range VSYNC SYNC Pin Input Threshold RSYNC SYNC Pin Input Resistance 250 Oscillator Frequency = 250kHz kHz 290 l 0.7 kHz 1.4 2.0 40 k 45 46 % 10 7.6 10.4 7.9 10.7 8.1 0.2 0.35 Gate Drives (Specifications Apply to Either A or B Unless Otherwise Noted) DCMAX Maximum Switch Duty Cycle RVSL = RCSL = 4.85k, Osc Frequency = 25kHz VGON Gate On Voltage VIN = 12, GCL = 12 VIN = 12, GCL = 8 VGOFF Gate Off Voltage VIN = 12V IGSO Max Gate Source Current VIN = 12V 0.3 IGSK Max Gate Sink Current VIN = 12V 0.3 VINUVLO Gate Drive Undervoltage Lockout (Note 5) VGCL = 6.5V, Gates Enabled l V V V A A 7.3 7.5 V 103 120 mV 230 300 mV Current Sense tIBL Switch Current Limit Blanking Time VSENSE Sense Voltage Shutdown Voltage VSENSEF Sense Voltage Fault Threshold 100 VC Pulled Low l 86 l ns Slew Control (for the Following Slew Tests See Test Circuit in Figure 1b) VSLEWR Output Voltage Slew Rising Edge RVSL = RCSL = 17k 26 V/s VSLEWF Output Voltage Slew Falling Edge RVSL = RCSL = 17k 19 V/s VISLEWR Output Current Slew Rising Edge (CS Pin Voltage) RVSL = RCSL = 17k 0.21 V/s VISLEWF Output Current Slew Falling Edge (CS Pin Voltage) RVSL = RCSL = 17k 0.21 V/s Supply and Protection VINMIN Minimum Input Voltage (Note 4) VGCL = VIN l 2.55 3.6 V IVIN Supply Current (Note 2) RVSL = RCSL = 17k , VIN = 12 RVSL = RCSL = 17k , VIN = 20 l l 25 35 45 55 mA mA VSHDN Shutdown Turn-On Threshold l 1.31 1.39 1.48 V VSHDN Shutdown Turn-On Voltage Hysteresis l 50 110 180 mV ISHDN Shutdown Input Current Hysteresis l 10 24 35 A V5 5V Reference Voltage 6.5V VIN 20V, IV5 = 5mA 6.5V VIN 20V, IV5 = - 5mA 4.85 4.80 5 5 5.20 5.15 V V IV5SC 5V Reference Short-Circuit Current VIN = 6.5V Source VIN = 6.5V Sink 10 -10 mA mA 1683fd 3 LT1683 ELECTRICAL CHARACTERISTICS Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: Supply current specification includes loads on each gate as in Figure 1a. Actual supply currents vary with operating frequency, operating voltages, V5 load, slew rates and type of external FET. Note 3: The LT1683E is guaranteed to meet performance specifications from 0C to 70C. Specifications over the -40C to 125C operating range are assured by design, characterization and correlation with statistical process controls. The LT1683I is guaranteed and tested over the - 40 to 125 operating temperature range. Note 4: Output gate drivers will be enabled at this voltage. The GCL voltage will also determine drivers' activity. Note 5: Gate drivers are ensured to be on when VIN is greater than the maximum value. TYPICAL PERFORMANCE CHARACTERISTICS Negative Feedback Voltage and Input Current vs Temperature 2.480 3.2 1.258 700 2.485 3.0 1.256 650 1.254 600 2.490 2.8 1.252 550 2.495 2.6 1.250 500 2.500 2.4 1.248 450 2.505 2.2 1.246 400 1.244 350 2.510 2.0 1.242 300 2.515 1.8 1.240 -50 -25 0 NEGATIVE FEEDBACK VOLTAGE (V) 750 2.520 -50 -25 250 25 50 75 100 125 150 TEMPERATURE (C) 0 1.6 25 50 75 100 125 150 TEMPERATURE (C) 1683 G01 1683 G02 Error Amp Output Current vs Feedback Pin Voltage from Nominal Error Amp Transconductance vs Temperature 2000 500 1.65 1900 400 1.60 1800 300 1700 200 1.55 1.50 1.45 1.40 1.35 1.30 1.25 1.20 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (C) 1683 G03 CURRENT (A) 1.70 TRANSCONDUCTANCE (mho) FEEDBACK VOLTAGE (V) Feedback Overvoltage Shutdown vs Temperature NFB INPUT CURRENT (A) 1.260 FB INPUT CURRENT (nA) FEEDBACK VOLTAGE (V) Feedback Voltage and Input Current vs Temperature 1600 1500 1400 100 25C 125C 0 -100 -200 1300 1200 -300 1100 -400 1000 -50 -25 - 40C 0 25 50 75 100 125 150 TEMPERATURE (C) 1683 G04 -500 -400 -300 -200 -100 0 100 200 300 400 FEEDBACK PIN VOLTAGE FROM NOMINAL (mV) 1683 G05 1683fd 4 LT1683 TYPICAL PERFORMANCE CHARACTERISTICS VC Pin Threshold and Clamp Voltage vs Temperature 1.50 240 220 1.0 200 0.8 0.6 0.4 FAULT 180 160 140 120 0.2 80 -50 -25 25 50 75 100 125 150 TEMPERATURE (C) 0 25 22 23 20 VIN CURRENT (mA) 17 WITH NO EXTERNAL MOSFETs VIN = 20 RCSL, RVSL = 17k 16 VIN = 12 RCSL, RVSL = 17k 14 0.6 0 0 25 50 75 100 125 150 TEMPERATURE (C) GATE DRIVE A/B PIN VOLTAGE (V) 90 80 70 60 20 30 DUTY CYCLE (%) 40 50 1683 G12 0 20 40 60 80 CS PIN VOLTAGE (mV) 100 Gate Drive A/B Low Voltage vs Temperature 10.7 6.5 0.50 10.6 6.4 0.45 GCL = 12V 10.5 6.3 10.4 6.2 10.3 6.1 VIN = 12V NO LOAD 10.2 6.0 10.1 5.9 10.0 5.8 GCL = 6V 9.90 5.7 9.80 5.6 9.70 -50 -25 0 120 1683 G11 Gate Drive A/B High Voltage vs Temperature VC PIN = 0.9V TA = 25C 10 0.8 1683 G10 110 0 1.0 0.2 10 -50 -25 Slope Compensation 100 1.2 0.4 12 25 50 75 100 125 150 TEMPERATURE (C) TA = 25C 1.4 VIN = 12 RCSL, RVSL = 5.7k 18 1683 G09 PERCENT OF MAX CS VOLTAGE CS Pin to VC Pin Transfer Function 1.6 5.5 25 50 75 100 125 150 TEMPERATURE (C) 1683 G13 GATE DRIVE A/B PIN VOLTAGE (V) SHDN PIN CURRENT (A) 24 0 25 50 75 100 125 150 TEMPERATURE (C) 1683 G08 VIN Current vs Temperature 27 19 0 1683 G07 SHDN Pin Hysteresis Current vs Temperature 21 OFF 1.25 -50 -25 25 50 75 100 125 150 TEMPERATURE (C) 1683 G06 15 -50 -25 1.35 VC PIN VOLTAGE (V) 0 ON 1.40 1.30 TRIP 100 0 -50 -25 1.45 SHDN PIN VOLTAGE (V) 1.2 CS PIN VOLTAGE (mV) VC PIN VOLTAGE (V) 1.4 50 SHDN Pin On and Off Thresholds vs Temperature CS Pin Trip and CS Fault Voltage vs Temperature 0.40 VIN = 12V NO LOAD 0.35 0.30 0.25 0.20 0.15 0.10 0.05 0 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (C) 1683 G14 1683fd 5 LT1683 TYPICAL PERFORMANCE CHARACTERISTICS Gate Drive Undervoltage Lockout Voltage vs Temperature Soft-Start Current vs Temperature 7.3 GCL = 6V 9.3 7.0 6.9 6.8 6.7 6.6 5.06 8.9 8.7 8.5 8.3 8.1 6.5 7.9 6.4 7.7 6.3 -50 -25 SS VOLTAGE = 0.9V 9.1 SS PIN CURRENT (A) VIN PIN VOLTAGE (V) 7.1 5.08 0 25 50 75 100 125 150 TEMPERATURE (C) V5 PIN VOLTAGE (V) 7.2 V5 Voltage vs Load Current 9.5 7.5 -50 -25 T = 125C 5.04 5.02 T = 25C 5.00 T = -40C 4.98 0 25 50 75 100 125 150 TEMPERATURE (C) 1683 G15 4.96 -15 -10 -5 0 5 LOAD CURRENT (mA) 1683 G16 10 15 1683 G17 PIN FUNCTIONS Part Supply V5 (Pin 5): This pin provides a 5V output that can sink or source 10mA for use by external components. V5 source current comes from VIN . Sink current goes to GND. VIN must be greater than 6.5V in order for this voltage to be in regulation. If this pin is used, a small capacitor (<1F) may be placed on this pin to reduce noise. This pin can be left open if not used. GND (Pin 11): Signal Ground. The internal error amplifier, negative feedback amplifier, oscillator, slew control circuitry, V5 regulator, current sense and the bandgap reference are referred to this ground. Keep the connection to this pin, the feedback divider and VC compensation network free of large ground currents. SHDN (Pin 14): The shutdown pin can disable the switcher. Grounding this pin will disable all internal circuitry. Increasing SHDN voltage will initially turn on the internal bandgap regulator. This provides a precision threshold for the turn on of the rest of the IC. As SHDN increases past 1.39V the internal LDO regulator turns on, enabling the control and logic circuitry. 24A of current is sourced out of the pin above the turn on threshold. This can be used to provide hysteresis for the shutdown function. The hysteresis voltage will be set by the Thevenin resistance of the resistor divider driving this pin times the current sourced out. Above approximately 2.1V the hysteresis current is removed. There is approximately 0.1V of voltage hysteresis on this pin as well. The pin can be tied high (to VIN for instance). VIN (Pin 17): Input Supply. All supply current for the part comes from this pin including gate drives and V5 regulator. Charge current for gate drives can produce current pulses of hundreds of milliamperes. Bypass this pin with a low ESR capacitor. When VIN is below 2.55V the part will go into supply undervoltage lockout where the gate drivers are driven low. This, along with gate drive undervoltage lockout, prevents unpredictable behavior during power up. PGND (Pin 20): Power Driver Ground. This ground comes from the MOSFET gate drivers. This pin can have several hundred milliamperes of current on it when the external MOSFETs are being turned off. Oscillator SYNC (Pin 6): The SYNC pin can be used to synchronize the part to an external clock. The oscillator frequency 1683fd 6 LT1683 PIN FUNCTIONS should be set close to the external clock frequency. Synchronizing the clock to an external reference is useful for creating more stable positioning of the switcher voltage and current harmonics. This pin can be left open or tied to ground if not used. gate drive will not be enabled until VIN > VGCL + 0.8V. If this pin is tied to VIN, then undervoltage lockout is disabled. CT (Pin 7): The oscillator capacitor pin is used in conjunction with RT to set the oscillator frequency. For RT = 16.9k: Slew Control COSC(nf) = 129/fOSC(kHz) RT (Pin 8): The oscillator resistor pin is used to set the charge and discharge currents of the oscillator capacitor. The nominal value is 16.9k. It is possible to adjust this resistance 25% to set oscillator frequency more accurately. Gate Drive GATE A, GATE B (Pins 1, 19): These pins connect to the gates of the external N-channel MOSFETs. GATE A and GATE B turn on with alternate clock cycles. These drivers are capable of sinking and sourcing at least 300mA. The GCL pin sets the upper voltage of the gate drive. The gate pins will not be activated until VIN reaches a minimum voltage as defined by the GCL pin (gate undervoltage lockout). The gate drive outputs have current limit protection to safe guard against accidental shorts. If the gate drive voltage is greater than about 1V the opposite gate drive is inhibited thus preventing cross conduction. GCL (Pin 3): This pin sets the maximum gate voltage to the GATE A and GATE B pins to the MOSFET gate drives. This pin should be either tied to a Zener, a voltage source or VIN. If the pin is tied to a Zener or a voltage source, the maximum gate drive voltage will be approximately VGCL - 0.2V. If it is tied to VIN, the maximum gate voltage is approximately VIN - 1.6. Approximately 50A of current can be sourced from this pin if VGCL < VIN - 0.8V. This pin also controls undervoltage lockout of the gate drives. If the pin is tied to a Zener or voltage source, the There is an internal 19V Zener tied from this pin to ground to provide a fail-safe for maximum gate voltage. CAP A, CAP B (Pins 2, 18): These pins are the feedback nodes for the external voltage slewing capacitors. Normally a small 1pf to 5pf capacitor is connected from this pin to the drain of its respective MOSFET. The voltage slew rate is inversely proportional to this capacitance and proportional to the current that the part will sink and source on this pin. That current is inversely proportional to RVSL. RCSL (Pin 15): A resistor to ground sets the current slew rate for the external drive MOSFETs during switching. The minimum resistor value is 3.3k and the maximum value is 68k. The time to slew between on and off states of the MOSFET current will determine how the di/dt related harmonics are reduced. This time is proportional to RCSL and RS (the current sense resistor) and maximum current. Longer times produce a greater reduction of higher frequency harmonics. RVSL (Pin 16): A resistor to ground sets the voltage slew rate for the drains of the external drive MOSFETs. The minimum resistor value is 3.3k and the maximum value is 68k. The time to slew between on and off states on the MOSFET drain voltage will determine how harmonics are reduced from this source. This time is proportional to RVSL, CVA/B and the input voltage. Longer times produce more rolloff of harmonics. CVA/B is the equivalent capacitance from CAP A or B to the drain of the MOSFET. Switch Mode Control CS (Pin 4): This is the input to the current sense amplifier. It is used for both current mode control and current slewing of the external MOSFETs. Current sense is accomplished via a sense resistor (RS) connected from the sources of the external MOSFETs to ground. CS is connected to the top of RS. Current sense is referenced to the GND pin. 1683fd 7 LT1683 PIN FUNCTIONS The switch maximum operating current will be equal to 0.1V/RS. At CS = 0.1V, the gate drivers will be immediately turned off (no slew control). If CS = 0.22V in addition to the drivers being turned off, VC and SS will be discharged to ground (short-circuit protection). This will hasten turn off on subsequent cycles. FB (Pin 9): The feedback pin is used for positive voltage sensing. It is the inverting input to the error amplifier. The noninverting input of this amplifier connects internally to a 1.25V reference. If the voltage on this pin exceeds the reference by 220mV, then the output drivers will immediately turn off the external MOSFETs (no slew control). This provides for output overvoltage protection When this input is below 0.9V then the current sense blanking will be disabled. This will assist start up. NFB (Pin 10): The negative feedback pin is used for sensing a negative output voltage. The pin is connected to the inverting input of the negative feedback amplifier through a 100k source resistor. The negative feedback amplifier provides a gain of -0.5 to the FB pin. The nominal regulation point would be -2.5V on NFB. This pin should be left open if not used. VC (Pin 12): The compensation pin is used for frequency compensation and current limiting. It is the output of the error amplifier and the input of the current comparator. Loop frequency compensation can be performed with an RC network connected from the VC pin to ground. The voltage on VC is proportional to the switch peak current. The normal range of voltage on this pin is 0.25V to 1.27V. However, during slope compensation the upper clamp voltage is allowed to increase with the compensation. During a short-circuit fault the VC pin will be discharged to ground. SS (Pin 13): The SS pin allows for ramping of the switch current threshold at startup. Normally a capacitor is placed on this pin to ground. An internal 9A current source will charge this capacitor up. The voltage on the VC pin cannot exceed the voltage on SS. Thus peak current will ramp up as the SS pin ramps up. During a short circuit fault the SS pin will be discharged to ground thus reinitializing soft-start. When SS is below the VC clamp voltage the VC pin will closely track the SS pin. This pin can be left open if not used. If NFB is being used then overvoltage protection will occur at 0.44V below the NFB regulation point. At NFB < -1.8 current sense blanking will be disabled. TEST CIRCUITS 20mA 5pF 0.9A 5pF IN5819 CAP A/CAP B IN5819 CAP A/CAP B ZVN3306A GATE A/GATE B + - 2 10 GATE A/GATE B Si4450DY CS + - 10 0.1 1683 F01a Figure 1a. Typical Test Circuitry 1683 F01b Figure 1b. Test Circuit for Slew 1683fd 8 LT1683 BLOCK DIAGRAM VIN CIN RCSL SHDN VIN V5 RVSL RCSL RVSL TO DRIVERS REGULATOR + NEGATIVE FEEDBACK AMP VREG - NFB 100k GCL 50k CAP A GATE A - FB + ERROR AMP SLEW CONTROL + CAP B 1.25V CVC CSS GATE B VC - SS CVB MB CS + COMP S CT MA PGND SENSE AMP + RT CVA RSENSE - Q FF RT R OSCILLATOR CT T Q FF QB SYNC SUB GND 1683 BD 1683fd 9 LT1683 OPERATION In noise sensitive applications switching regulators tend to be ruled out as a power supply option due to their propensity for generating unwanted noise. When switching supplies are required due to efficiency or input/output constraints, great pains must be taken to work around the noise generated by a typical supply. These steps may include pre and post regulator filtering, precise synchronization of the power supply oscillator to an external clock, synchronizing the rest of the circuit to the power supply oscillator or halting power supply switching during noise sensitive operations. The LT1683 greatly simplifies the task of eliminating supply noise by enabling the design of an inherently low noise switching regulator power supply. The LT1683 is a fixed frequency, current mode switching regulator with unique circuitry to control the voltage and current slew rates of the output switches. Current mode control provides excellent AC and DC line regulation and simplifies loop compensation. Slew control capability provides much greater control over the power supply components that can create conducted and radiated electromagnetic interference. Compliance with EMI standards will be an easier task and will require fewer external filtering components. The LT1683 uses two external N-channel MOSFETs as the power switches. This allows the user to tailor the drive conditions to a wide range of voltages and currents. CURRENT MODE CONTROL Referring to the Block Diagram. A switching cycle begins with an oscillator discharge pulse, which resets the RS flip-flop, turning on one of the external MOSFET drivers. The switch current is sensed across the external sense resistor and the resulting voltage is amplified and compared to the output of the error amplifier (VC pin). The driver is turned off once the output of the current sense amplifier exceeds the voltage on the VC pin. In this way pulse by pulse current limit is achieved. The toggle flip-flop ensures that the two MOSFETs are enabled on alternate clock cycles. Internal slope compensation is provided to ensure stability under high duty cycle conditions. Output regulation is obtained using the error amp to set the switch current trip point. The error amp is a transconductance amplifier that integrates the difference between the feedback output voltage and an internal 1.25V reference. The output of the error amp adjusts the switch current trip point to provide the required load current at the desired regulated output voltage. This method of controlling current rather than voltage provides faster input transient response, cycle-by-cycle current limiting for better output switch protection and greater ease in compensating the feedback loop. The VC pin is used for loop compensation and current limit adjustment. During normal operation the VC voltage will be between 0.25V and 1.27V. An external clamp on VC or SS may be used for lowering the current limit. The negative voltage feedback amplifier allows for direct regulation of negative output voltages. The voltage on the NFB pin gets amplified by a gain of - 0.5 and driven on to the FB input, i.e., the NFB pin regulates to -2.5V while the amplifier output internally drives the FB pin to 1.25V as in normal operation. The negative feedback amplifier input impedance is 100k (typ) referred to ground. Soft-Start Control of the switch current during start-up can be obtained by using the SS pin. An external capacitor from SS to ground is charged by an internal 9A current source. The voltage on VC cannot exceed the voltage on SS. Thus as the SS pin ramps up the VC voltage will be allowed to ramp up. This will then provide for a smooth increase in switch maximum current. SS will be discharged as a result of the CS voltage exceeding the short-circuit threshold of approximately 0.22V. Slew Control Control of output voltage and current slew rates is achieved via two feedback loops. One loop controls the MOSFET drain dV/dt and the other loop controls the MOSFET dI/dt. The voltage slew rate uses an external capacitor between CAP A or CAP B and the respective MOSFET drain. These integrating caps close the voltage feedback loop. The external resistor, RVSL, sets the current for the integrator. 1683fd 10 LT1683 OPERATION The voltage slew rate is thus inversely proportional to both the value of capacitor and RVSL. The current slew feedback loop consists of the voltage across the external sense resistor, which is internally amplified and differentiated. The derivative is limited to a value set by RCSL. The current slew rate is thus inversely proportional to both the value of sense resistor and RCSL. The two control loops are combined internally so that a smooth transition from current slew control to voltage slew control is obtained. When turning on, the driver current will slew before voltage. When turning off, voltage will slew before current. In general it is desirable to have RVSL and RCSL of similar value. Internal Regulator Most of the control circuitry operates from an internal 2.4V low dropout regulator that is powered from VIN. The internal low dropout design allows VIN to vary from 2.7V to 20V with stable operation of the controller. When SHDN < 1.3V the internal regulator is completely disabled. 5V Regulator A 5V regulator is provided for powering external circuitry. This regulator draws current from VIN and requires VIN to be greater than 6.5V to be in regulation. It can sink or source 10mA. The output is current limited to prevent against destruction from accidental short circuits. Safety and Protection Features There are several safety and protection features on the chip. The first is overcurrent limit. Normally the gate drivers will go low when the output of the internal sense amplifier exceeds the voltage on the VC pin. The VC pin is clamped such that maximum output current is attained when the CS pin voltage is 0.1V. At that level the outputs will be immediately turned off (no slew). The effect of this control is that the output voltage will foldback with overcurrent. In addition, if the CS voltage exceeds 0.22V, the VC and SS pins will be discharged to ground also, resetting the soft-start function. Thus if a short is present this will allow for faster MOSFET turnoff and less MOSFET stress. If the voltage on the FB pin exceeds regulation by approximately 0.22V, the outputs will immediately go low. The implication is that there is an overvoltage fault. The voltage on GCL determines two features. The first is the maximum gate drive voltage. This will protect the MOSFET gate from overvoltage. With GCL tied to a Zener or an external voltage source then the maximum gate driver voltage is approximately VGCL - 0.2V. If GCL is tied to VIN , then the maximum gate voltage is determined by VIN and is approximately VIN - 1.6V. There is an internal 19V Zener on the GCL pin that prevents the gate driver pin from exceeding approximately 19V. In addition, the GCL voltage determines undervoltage lockout of the gate drives. This feature disables the gate drivers if VIN is too low to provide adequate voltage to turn on the MOSFETs. This is helpful during start-up to ensure the MOSFETs have sufficient gate drive to saturate. If GCL is tied to a voltage source or Zener less than 6.8V, the gate drivers will not turn on until VIN exceeds GCL voltage by 0.8V. For VGCL above 6.5V, the gate drives are ensured to be off for VIN < 7.3V and they will be turned on by VGCL + 0.8V. If GCL is tied to VIN, the gate drivers are always enabled (undervoltage lockout is disabled). When driving a push-pull transformer, it is important to make sure that both drivers are not on at the same time. Even though runaway cannot occur under such cross conduction with this chip because current slew is regulated, increased current would be possible. This chip has opposite gate lockout whereby when one MOSFET is on the other MOSFET cannot be turned on until the gate of the first drops below 1V. This ensures that cross conduction will not occur. The gate drives have current limits for the drive currents. If the sink or source current is greater than 300mA then the current will be limited. The V5 regulator also has internal current limiting that will only guarantee 10mA output current. 1683fd 11 LT1683 OPERATION There is also an on-chip thermal shutdown circuit that will turn off the outputs in the event the chip temperature rises to dangerous levels. Thermal shutdown has hysteresis that will cause a low frequency (<1kHz) oscillation to occur as the chip heats up and cools down. The chip has an undervoltage lockout feature that will force the gate drivers low in the event that VIN drops below 2.5V. This ensures predictable behavior during start-up and shutdown. SHDN can be used in conjuction with an external resistor divider to completely disable the part if the input voltage is too low. This can be used to ensure adequate voltage to reliably run the converter. See the section in Applications Information. Table 1 summarizes these features. Table 1. Safety and Protection Features FEATURE FUNCTION EFFECT ON GATE DRIVERS SLEW CONTROL EFFECT ON VC, SS Maximum Current Fault Turn Off FETs at Maximum Switch Current (VSENSE = 0.1) Immediately Goes Low Overridden None Short-Circuit Fault Turn Off FETs and Reset VC for Short-Circuit (VSENSE = 0.2) Immediately Goes Low Overridden Discharge VC, SS to GND Overvoltage Fault Turn Off Drivers If FB > VREG + 0.22V (Output Overvoltage) Immediately Goes Low Overridden None GCL Clamp Set Max Gate Voltage to Prevent FET Gate Breakdown Limits Max Voltage None None Gate Drive Undervoltage Lockout Disable Gate Drives When VIN Is Too Low. Set Via GCL Pin Immediately Goes Low Overridden None Thermal Shutdown Turn Off Drivers If Chip Temperature Is Too Hot Immediately Goes Low Overridden None Opposite Gate Lockout Prevents Opposite Driver from Turning on Until Driver Is Off (Cross Conduction in Transformer) Inhibits Turn On of Opposite Driver None None VIN Undervoltage Lockout Disable Part When VIN 2.55V Immediately Goes Low Overridden None Gate Drive Source and Sink Current Limit Limit Gate Drive Current Limit Drive Current None None V5 Source/Sink Current Limit Limit Current from V5 None None None Shutdown Disable Part When SHDN <1.3V 1683fd 12 LT1683 APPLICATIONS INFORMATION Reducing EMI from switching power supplies has traditionally invoked fear in designers. Many switchers are designed solely on efficiency and as such produce waveforms filled with high frequency harmonics that then propagate through the rest of the system. The LT1683 provides control over two of the more important variables for controlling EMI with switching inductive loads: switch voltage slew rate and switch current slew rate. The use of this part will reduce noise and EMI over conventional switch mode controllers. Because these variables are under control, a supply built with this part will exhibit far less tendency to create EMI and less chance of encountering problems during production. It is beyond the scope of this data sheet to get into EMI fundamentals. Application Note 70 contains much information concerning noise in switching regulators and should be consulted. Oscillator Frequency The oscillator determines the switching frequency and therefore the fundamental positioning of all harmonics. The use of good quality external components is important to ensure oscillator frequency stability. The oscillator is of a sawtooth design. A current defined by external resistor, RT, is used to charge and discharge the capacitor, CT . The discharge rate is approximately ten times the charge rate. By allowing the user to have control over both components, trimming of oscillator frequency can be more easily achieved. The external capacitance CT is chosen by: CT (nF) = 2180 f(kHz) *R T (k) where f is the desired oscillator frequency in kHz. For RT equal to 16.9k, this simplifies to: CT (nF) = 129 f(kHz) Nominally RT should be 16.9k. Since it sets up current, its temperature coefficient should be selected to compliment the capacitor. Ideally, both should have low temperature coefficients. Oscillator frequency is important for noise reduction in two ways. First the lower the oscillator frequency the lower the waveform's harmonics, making it easier to filter them. Second the oscillator will control the placement of the output voltage harmonics which can aid in specific problems where you might be trying to avoid a certain frequency bandwidth. Oscillator Sync If a more precise frequency is desired (e.g., to accurately place harmonics) the oscillator can be synchronized to an external clock. Set the RC timing components for an oscillator frequency 10% lower than the desired sync frequency. Drive the SYNC pin with a square wave (with greater than 1.4V amplitude). The rising edge of the sync square wave will initiate clock discharge. The sync pulse should have a minimum pulse width of 0.5s. Be careful in sync'ing to frequencies much different from the part since the internal oscillator charge slope determines slope compensation. It would be possible to get into subharmonic oscillation if the sync doesn't allow for the charge cycle of the capacitor to initiate slope compensation. In general, this will not be a problem until the sync frequency is greater than 1.5 times the oscillator free-run frequency. Slew Rate Setting The primary reason to use this part is to gain advantage of lower EMI and noise due to slew control. The rolloff in higher frequency harmonics has its theoretical basis with two primary components. First, the clock frequency sets the fundamental positioning of harmonics and second, the associated normal frequency rolloff of harmonics. e.g., CT = 1.29nF for f = 100kHz 1683fd 13 LT1683 APPLICATIONS INFORMATION This part creates a second higher frequency rolloff of harmonics that inversely depends on the slew time, the time that voltage or current spends between the off state and on state. This time is adjustable through the choice of the slew resistors, the external resistors to ground on the RVSL and RCSL pins and the external components used for the external voltage feedback capacitors CAV, CBV (from CAP A or CAP B to their respective MOSFET drains) and the sense resistor. Lower slew rates (longer slew times, lower frequency for harmonics rolloff) is created with higher values of RVSL, RCSL, CAV, CBV and the current sense resistor. Setting the voltage and current slew rates should be done empirically. The most practical way of determining these components is to set CAV, CBV and the sense resistor value. Then, start by making RVSL, RCSL each a 50k resistor pot in series with 3.3k. Starting from the lowest resistor setting (fast slew) adjust the pots until the noise level meets your guidelines. Note that slower slewing waveforms will dissipate more power so that efficiency will drop. You can monitor this as you make your slew adjustment by measuring input and output voltage and their respective currents. Monitor the MOSFET temperature as slew rates are slowed. These components will heat up as efficiency decreases. Measuring noise should be done carefully. It is easy to introduce noise by poor measurement techniques. Consult AN70 for recommended measurement techniques. Keeping probe ground leads very short is essential. Usually it will be desirable to keep the voltage and current slew resistors approximately the same. There are circumstances where a better optimization can be found by adjusting each separately, but as these values are separated further, a loss of independence of control may occur. It is possible to use a single slew setting resistor. In this case the RVSL and RCSL pins are tied together. A resistor with a value of 1.8k to 34k (one-half the individual resistors) can then be tied from these pins to ground. In general only the RCSL value will be available for adjustment of current slew. The current slew time does also depend on the current sense resistor but this resistor is normally set with consideration of the maximum current in the MOSFETs. Setting the voltage slew also involves selection of the capacitors CAV, CBV. The voltage slew time is proportional to the output voltage swing (basically input voltage), the external voltage feedback capacitor and the RVSL value. Thus at higher input voltages smaller capacitors will be used with lower RVSL values. For a starting point use Table 2. Table 2 INPUT VOLTAGE CAPACITOR VALUE <25V 5pF 50V 2.5pF 100V 1pF Smaller value capacitors can be made in two ways. The first is simply combining two capacitors in series. The equivalent capacitance is then (C1 * C2)/(C1 + C2). The second method makes use of a capacitor divider. Care should be taken that the voltage ratings of the capacitors satisfy the full voltage swing (2x input voltage for pushpull configurations) thus essentially the same rating as the MOSFETs. MOSFET DRAIN CAP A OR B C2 C1 C3 1683 F02 Figure 2 The equivalent slew capacitance for Figure 2 is (C1 * C2)/(C1 + C2 + C3). Positive Output Voltage Setting Sensing of a positive output voltage is usually done using a resistor divider from the output to the FB pin. The positive input to the error amp is connected internally to a 1.25V bandgap reference. The FB pin will regulate to this voltage. Referring to Figure 3, R1 is determined by: V R1= R2 OUT - 1 1.25 1683fd 14 LT1683 APPLICATIONS INFORMATION The FB bias current represents a small error and can usually be ignored for values of R1||R2 up to 10k. One word of caution, sometimes a feedback zero is added to the control loop by placing a capacitor across R1. If the feedback capacitively pulls the FB pin above the internal regulator voltage (2.4V), output regulation may be disrupted. A series resistance with the feedback pin can eliminate this potential problem. There is an internal clamp on FB that clamps at 0.7V above the regulation voltage that should also help prevent this problem. R1 FB PIN VOUT R2 1683 F03 Figure 3 Negative Output Voltage Setting Negative output voltage can be sensed using the NFB pin. In this case regulation will occur when the NFB pin is at -2.5V. The nominal input bias current for the NFB is -25A (INFB), which needs to be accounted for in setting up the divider. Referring to Figure 4, R1 is chosen such that: VOUT - 2.5 R1= R2 2.5 +R2 * 25A R1 INFB Shutdown If SHDN is pulled low, the regulator will turn off. As the SHDN pin voltage is increased from ground the internal bandgap regulator will be powered on. This will set a 1.39V threshold for turn-on of the internal regulator that runs most of the control circuitry of the regulator. Note after the control circuitry powers on, gate driver activity will depend on the voltage of VIN with respect to the voltage on GCL. As the SHDN pin enables the internal regulator a 24A current will be sourced from the pin that can provide hysteresis for undervoltage lockout. This hysteresis can be used to prevent part shutdown due to input voltage sag from an initial high current draw. In addition to the current hysteresis, there is also approximately 100mV of voltage hysteresis on the SHDN pin. When the SHDN pin is greater than 2.2V, the hysteretic current from the part will be reduced to essentially zero. If a resistor divider is used to set the turn-on threshold then the resistors are determined by the following equations: A suggested value for R2 is 2.5k. The NFB pin is normally left open if the FB pin is being used. NFB PIN the LT1683 will act to prevent either output from going beyond its set output voltage. The highest output (lightest load) will dominate control of the regulator. This technique would prevent either output from going unregulated high at no load. However, this technique will also compromise output load regulation. -VOUT R2 RA +RB VON = *V RB SHDN VIN RA SHDN RB V VHYST = RA * SHDN +ISHDN RA RB 1683 F04 Figure 4 Dual Polarity Output Voltage Sensing Certain applications may benefit from sensing both positive and negative output voltages. When doing this each output voltage resistor divider is individually set as previously described. When both FB and NFB pins are used, Reworking these equations yields: RA = (VHYST * VSHDN - VON * VSHDN ) (ISHDN * VSHDN ) RB = (VHYST * VSHDN - VON * VSHDN ) ISHDN *(VON - VSHDN ) 1683fd 15 LT1683 APPLICATIONS INFORMATION So if we wanted to turn on at 20V with 2V of hysteresis: 2V * 1.39V - 20V * 0.1V = 23.4k 24A * 1.39V 2V * 1.39V - 20V * 0.1V RB = = 1.75k 24A *(20V - 1.39V) RA = Resistor values could be altered further by adding Zeners in the divider string. A resistor in series with SHDN pin could further change hysteresis without changing turn-on voltage. Frequency Compensation Loop frequency compensation is accomplished by way of a series RC network on the output of the error amplifier (VC pin). VC PIN RVC 2k CVC2 4.7nF CVC 0.01F 1683 F06 Figure 6 Referring to Figure 6, the main pole is formed by capacitor CVC and the output impedance of the error amplifier (approximately 400k). The series resistor, RVC, creates a "zero" which improves loop stability and transient response. A second capacitor, CVC2, typically one-tenth the size of the main compensation capacitor, is sometimes used to reduce the switching frequency ripple on the VC pin. VC pin ripple is caused by output voltage ripple attenuated by the output divider and multiplied by the error amplifier. Without the second capacitor, VC pin ripple is: VCPINRIPPLE = 1.25 * VRIPPLE * gm *R VC VOUT where VRIPPLE = Output ripple (VP-P ) gm = Error amplifier transconductance RVC = Series resistor on VC pin VOUT = DC output voltage To prevent irregular switching, VC pin ripple should be kept below 50mVP-P . Worst-case VC pin ripple occurs at maximum output load current and will also be increased if poor quality (high ESR) output capacitors are used. The addition of a 0.0047F capacitor for CVC2 pin reduces switching frequency ripple to only a few millivolts. A low value for RVC will also reduce VC pin ripple, but loop phase margin may be inadequate. Setting Current Limit The sense resistor sets the value for maximum operating current. When the CS pin voltage is 0.1V the gate drivers will immediately go low (no slew control). Therefore the sense resistor value should be set to RS = 0.1V/ISW(PEAK), where ISW(PEAK) is the peak current in the MOSFETs. ISW(PEAK) will depend on the topology and component values and tolerances. Certainly it should be set below the saturation current value for the transformer. If CS pin voltage is 0.22V in addition to the drivers going low, VC and SS will be discharged to ground. This is to provide additional protection in the event of a short circuit. By discharging VC and SS, the MOSFET will not be stressed as hard on subsequent cycles since the current trip will be set lower. Turn-off of the MOSFETs will normally be inhibited for about 100ns at the start of every turn on cycle. This is to prevent noise from interfering with normal operation of the controller. This current sense blanking does not prevent the outputs from be turned off in the event of a fault. Slewing of the gate voltage effectively provides additional blanking. Traces to the SENSE resistor should be kept short and wide to minimize resistance and inductance. Large interwinding capacitance in the transformer or high capacitance on the drain of the MOSFETs will produce a current pulse through the sense resistor during drain voltage slewing. The magnitude of the pulse is C * dV/dt where C is the capacitance and dV/dt is the voltage slew rate which is controlled by the part. This pulse will increase the sensed current on switch turn-on and can cause premature MOSFET turn-off. If this occurs, the transformer may need a different winding technique (see AN39) or alternatively, a blanking circuit can be used. Please contact the LTC applications group for support if required. 1683fd 16 LT1683 APPLICATIONS INFORMATION Soft-Start Magnetics The soft-start pin is used to provide control of switching current during start-up. The max voltage on the VC pin is approximately the voltage on the SS pin. A current source will linearly charge a capacitor on the SS pin. The VC pin voltage will thus ramp also. The approximate time for the voltage on these pins to ramp is (1.31V/9A) * CSS or approximately 146ms per F. Design of magnetics is dependent on topology. The following details the design of the magnetics for a push-pull converter. In this converter the transformer usually stores little energy. The following equations should be considered as the starting point to building a prototype. The following definitions will be used: VIN = Input supply voltage The soft-start current will be initiated as soon as the part turns on. Soft-start will be reinititated after a short-circuit fault. ISW = Maximum switch current Thermal Considerations VOUT = Desired output voltage Most of the IC power dissipation is derived from the VIN pin. The VIN current depends on a number of factors including: oscillator frequency; loads on V5; slew settings; gate charge current. Additional power is dissipated if V5 sinks current and during the MOSFET gate discharge. IOUT = Output current The power dissipation in the IC will be the sum of: 1) The RMS VIN current times VIN 2) V5 RMS sink current times 5V 3) The gate drive's RMS discharge current times voltage Because of the strong VIN component it is advantageous to operate the LT1683 at as low a VIN as possible. It is always recommended that package temperature be measured in each application. The part has an internal thermal shutdown to minimize the chance of IC destruction but this should not replace careful thermal design. The thermal shutdown feature does not protect the external MOSFETs. A separate analysis must be done for those devices to ensure that they are operating within safe limits. Once IC power dissipation, PDIS, is determined die junction temperature is then computed as: TJ = TAMB + PDIS * JA where TAMB is ambient temperature and JA is the package thermal resistance. For the 20-pin SSOP, JA is 100C/W. RON = Switch-on resistance f = Oscillator frequency VF = Forward drop of the rectifier Duty cycle is the major defining equation for this topology. Note that the output L and C basically filter the chopped voltage so duty cycle controls output voltage. N is the turns ratio of the transformer. The turns ratio must be large enough to ensure that the transformer can put out a voltage equal to the output voltage plus the diode under minimum input conditions. Note the transformer operates at half the oscillator frequency (f). N= VOUT + VF (2 *DCMAX ) VIN(MIN) -ISW (RON +RSENSE ) DCMAX is the maximum duty cycle of each driver with respect to the entire cycle, which consists of two periods (A on and B on). So the effective duty cycle is 2 * DCMAX. The controller, in general, determines maximum duty cycle. A 44% maximum duty cycle is a guaranteed value for this part. Remember to add sufficient margin in the turns ratio to account for IR drops in the transformer windings, worstcase diode forward drops and switch-on voltage. Also at very slow slew rates the effective DC may be reduced. 1683fd 17 LT1683 APPLICATIONS INFORMATION There are a number of ways to choose the inductance value for L. We suggest as a starting point that L be selected such that the converter is continuous at IOUT(MAX)/4. If your minimum IOUT is higher than this or your components can handle higher peak currents then use a higher number. 1:N D1 L VOUT C ROUT VIN LPRI D2 RSENSE 1683 F07 Figure 7. Push-Pull Topology Continuous operation occurs when the current in the inductor never goes to zero. Discontinuous operation occurs when the inductor current drops to zero before the start of the next cycle and can occur with small inductors and light loads. There is nothing inherently bad about discontinuous operation, however, converter control and operation are somewhat different. The inductor is smaller for discontinuous operation but the peak currents in the switch, the transformer, the diodes, inductor and capacitor will be higher which may produce greater losses. For continuous operation the inductor ripple current must be less than twice the output current. The worst case for this is at maximum input (lowest duty cycle, DCMIN) but in the following we will evaluate at nominal input since the IOUT/4 is somewhat arbitrary. Note when both inputs are off, the inductor current splits between both secondary outputs and the diode common goes to 0V. Looking at the inductor current during off time, output ripple current is: IOUT = 2 *IOUT(MIN) IOUT(MIN) = IOUT(MAX) / 4 L= ( VOUT(MIN) + VF ) * (1- 2 * DC ) The inductance of the transformer primary should be such that L, when reflected into the primary, dominates the input current. In other words, we want the magnetizing current of the transformer small with respect to the current going through the transformer to L. In general, then, the inductance of the primary should be at least five times that of L reflected to the input. This ensures that most of the power will be passed through the transformer to the load. It also increases the power capability of the converter and reduces the peak currents that the switch will see. 5 *L LPRI = 2 N If the magnetizing current is small, say below 100mA, then a smaller L can be used with a higher percentage of the switch current generated by the magnetizing current. With the value of L set, the ripple in the inductor is: IL = ( VOUT + VF ) * (1- 2 *DC) L*f However, the peak inductor current is evaluated at maximum load and maximum input voltage (minimum DC). IL(MAX) =IOUT(MAX) + IL(MAX) 2 The magnetizing ripple current can be shown to be: V +V IMAG = OUT F N *LPRI * f and the peak current in the switch is: ISW(PEAK) = N * IL(MAX) + IMAG This current should be less than the current limit. Worst-case switch ripple is: ISW(PEAK) = N * IL(MAX) + IMAG In the push-pull converter the maximum switch voltage will be 2 * VIN. Because voltage is slew-controlled, the leakage spikes are small. So, the MOSFET should have a maximum rated switch voltage at least 20% higher than 2 * VIN. IOUT * f 1683fd 18 LT1683 APPLICATIONS INFORMATION So, given the turns ratio, primary inductance and current, the transformer can be designed. The design of the transformer will require analyzing the power losses of the transformer and making necessary adjustments. The maximum inductor current is: 1.03A IL(MAX) = 2A + = 2.52A 2 Most transformer companies can assist you with designing an optimal solution. For instance Midcom, Inc. (1-800643-2661). Linear Technology's application group can also help. Primary inductance should be greater than: As an example say we are designing a 48V 20% to 5V 100kHz converter with 2A output and 500mA ripple. Then starting with a guess for the on voltage of the MOSFET plus sense resistor of 0.5V and VF of 0.5V: 5 + 0.5 1 N= = 88% * ( 48 * 80% - 0.5) 6.1 For continuous operation at IOUT(MIN) = IOUT(MAX)/4, inductor ripple (the same as output ripple): 2A IL = 2 * = 1A 4 The duty cycle for nominal input is: VOUT + VF DCNOM = 2 *N VIN(NOM) -ISW *RON ( = Then: L= 5.5 2 * 47.5 6.1 ) = 35.3% (5 + 0.5) * (1- 2 * 35.3%) = 16H 1A * 100kHz Off-the-shelf components can be used for this inductor. Say we choose a 22H inductor, then ripple current at maximum input (DC = 29.1%) is: IL = (5 + 0.5) * (1- 2 * 29.1%) = 1.03A 22F * 100kHz LPRI = 5 * 22H * 6.12 = 4.1mH The secondary inductance would then be: 4.1mH/6.12 = 110H The magnetizing ripple current is approximately: IMAG = 5.5 1 * 4.1mH * 100kHz 6.1 = 81mA Peak switch current is: ISW(PEAK) = 1 * 2.51A + 81mA = 494mA 6.1 Note that you can discern your magnetizing ripple by looking at the reflected inductance ripple and subtracting it from the switch current ripple. IMAG = ISW - N * IL The max ripple current on the switch is: ISW(MAX) = 1.03A + 81mA = 0.25A 6.1 Knowing the peak switch current we can go back and iterate with a more accurate switch-on voltage. We would have to know the RON of the FET. In our case our assumptions of a 0.5V switch-on voltage is valid for RON + RSENSE < 1. Capacitors Correct choice of input and output capacitors is very important to low noise switcher performance. Push-pull topologies and other low noise topologies will in general have continuous currents, which reduce the requirements 1683fd 19 LT1683 APPLICATIONS INFORMATION for capacitance. However, noise depends more on the ESR of the capacitors. In addition lower ESR can also improve efficiency. Input capacitors must also withstand surges that occur during the switching of some types of loads. Some solid tantalum capacitors can fail under these surge conditions. Design Note 95 offers more information but the following is a brief summary of capacitor types and attributes. Aluminum Electrolytic: Low cost and higher voltage. They can be used in this application but in general you will need higher capacitance to achieve low ESR. Additional nonelectrolytic capacitors may be required to achieve better performance. Specialty Polymer Aluminum: Panasonic has come out with their series CD capacitors. While they are only available for voltages below 16V, they have very low ESR and good surge capability. The worst component from an AC point is the gate charge current. The actual peak current depends on gate capacitance and slew rate, being higher for larger values of each. The total current can be estimated by gate charge and frequency of operation. Because of the slewing with this part, gate charge is spread out over a longer time period than with a normal FET driver. This reduces capacitance requirements. Typically the current will have spikes of under 100mA located at the gate voltage transitions. This is charge/discharge to and from the threshold voltage. Most slewing occurs with the gate voltage near threshold. Since the part's VIN will typically be under 15V many options are available for choice of capacitor. Values of input capacitor for just VIN requirement will typically be in the 50F range with an ESR of under 0.1. Solid Tantalum: Small size and low impedance. Typically the maximum voltage rating is 50V. With large surge currents the capacitor may need to be derated or you need a special type such as AVX TPS line. In addition to the part supply, decoupling of the supply to the transformer needs to be considered. If this is the same supply as the VIN pin then that capacitor will need to be increased. However, often with this part the transformer supply will be a higher voltage and as such a separate capacitor. OS-CON: Lower impedance than aluminum but only available for 35V or less. Form factor may be a problem. The transformer decoupling capacitor will see the switch current as ripple. Ceramic: Generally used for high frequency and high voltage bypass. They may resonate with their ESL before ESR becomes dominant. Recent multilayer ceramic (MLC) capacitors provide larger capacitance with low ESR. This switch current computation can be used to estimate the capacity for these capacitors: 1 DC CIN = * MIN VCAP f -ESR ISW(MAX) There are continuous improvements being made in capacitors so consult with manufacturers as to your specific needs. Input Capacitors The input capacitor should have low ESR at high frequencies since this will be an important factor concerning how much conducted noise is created. There are two separate requirements for input capacitors. The first is for supply to the part's VIN pin. The VIN pin will provide current for the part itself and the gate charge current. where VCAP is the allowed sag on the input capacitor. ESR is the equivalent series resistance for the cap. In general allowed sag will be a few tenths of volts. Output Filter Capacitor The output capacitor is chosen both for capacity and ESR. The capacity must supply the load current in the switchoff state. While slew control reduces higher frequency components of the ripple current in the capacitor, the capacitor ESR and the magnitude of the output ripple 1683fd 20 LT1683 APPLICATIONS INFORMATION current controls the fundamental component. ESR should also be low to reduce capacitor dissipation. The capacitance value can be computed by consideration of desired load ripple, duty cycle and ESR. Setting the voltage on the GCL pin depends on what type of MOSFET is used and the desired gate drive undervoltage lockout voltage. DCMIN f -ESR MOSFET Selection First determine the maximum gate drive that you require. Typically you will want it to be at least 2V greater than the maximum threshold. Higher voltages will lower the on resistance and increase efficiency. Be certain to check the maximum allowed gate voltage. Often this is 20V but for some logic threshold MOSFETs it is only 8V to 10V. There is a wide variety of MOSFETs to choose from for this part. The part will work with either normal threshold (3V to 4V) or logic-level threshold devices (1V to 2V). VGCL needs to be set approximately 0.2V above the desired max gate threshold. In addition VIN needs to be at least 1.6V above the gate voltage. Select a voltage rating to ensure under worst-case conditions that the MOSFET will not break down. Next choose an RON sufficiently low to meet both the power dissipation capabilities of the MOSFET package as well as overall efficiency needs of the converter. The GCL pin can be tied to VIN which will result in a maximum gate voltage of VIN - 1.6V. COUT = 1 Setting GCL Voltage VOUT IL(MAX) * The LT1683 can handle a large range of gate charges. However at very large charge stability may be affected. The power dissipation in the MOSFET depends on several factors. The primary element is I2R heating when the device is on. In addition, power is dissipated when the device is slewing. An estimate for power dissipation is: 3 * I2 2 2 VIN - RON2 * I2 + 2 I I + 4 4 + P = VIN * * I VSR ISR * f + I2 * RON * DC where I is the average current, I is the ripple current in the switch, ISR is the current slew rate, VSR is the voltage slew rate, f is the oscillator frequency, DC is the duty cycle and RON is the MOSFET on-resistance. This pin also controls undervoltage lockout of the gate drives. The undervoltage lockout will prevent the MOSFETs from switching until there is sufficient drive present. If GCL is tied to a voltage source or Zener less than 6.8V, the gate drivers will not turn on until VIN exceeds the GCL voltage by 0.8V. For VGCL above 6.5V, the gate drives are ensured to be off for VIN < 7.3V and they will be turned on by VGCL + 0.8V. If GCL is tied to VIN , the gate drivers are always on (undervoltage lockout is disabled). Approximately 50A of current can be sourced from this pin if VIN > VGCL + 0.8V. This could be used to bias a Zener. The GCL pin has an internal 19V Zener to ground that will provide a failsafe for maximum gate voltage. As an example say we are using a Siliconix Si4480DY which has RDS(ON) rated at 6V. To get 6V, VGCL needs to be set to 6.2V and VIN needs to be at least 7.6V. 1683fd 21 LT1683 APPLICATIONS INFORMATION Gate Driver Considerations In general, the MOSFETs should be positioned as close to the part as possible to minimize inductance. When the part is active the gate drives will be pulled low to less than 0.2V. When the part is off, the gate drives contain a 40k resistor in series with a diode to ground that will offer passive holdoff protection. If you are using some logic-level MOSFETs this might not be sufficient. A resistor may be placed from gate to ground, however the value should be reasonably high to minimize DC losses and possible AC issues. The gate drive source current comes from VIN . The sink current exits through PGND. In general the decoupling cap should be placed close to these two pins. Switching Diodes In general, switching diodes should be Schottky diodes. Size and breakdown voltage depend on the specific converter. A lower forward drop will improve converter efficiency. No other special requirements are needed. PCB Layout Considerations As with any switcher careful consideration should be given to PC board layout. Because this part reduces high frequency EMI the board layout is less critical, however high currents and voltages still produce the need for careful board layout to eliminate poor and erratic performance. the ground paths of other loops. Using singular points of connection for the grounds is the best way to do this. The two major points of connection are the bottom of the input decoupling cap and the bottom of the output decoupling cap. Typically the sense resistor device PGND and device GND will tie to the bottom of the input cap. There are two other loops to pay attention to. The current slew involves a high bandwidth control that goes through the MOSFET switch, the sense resistor and into the CS pin of the part and out the GATE pin to the MOSFET. Trace inductance and resistance should be kept low on the GATE drive trace. The CS trace should have low inductance. The sense resistor should be physically close to PGND and the MOSFETs' sources. Finally care should be taken with the CAP A, CAP B pins. The part will tolerate stray capacitance to ground on these pins (<5pF) however stray capacitance to the respective drains should be minimized. This path would provide an alternate capacitive path for the voltage slew. More Help AN70 contains information about low noise switchers and measurement of noise and should be consulted. AN19 and AN29 also have general knowledge concerning switching regulators. Also, our Application Department is always ready to lend a helping hand. A Basic Considerations Keep the high current loops physically small in area. The main loops are shown in Figure 8: the power switch loops (A and B) and the rectifier loop (C and D). These loops can be kept small by physically keeping the components close to one another. In addition, connection traces should be kept wide to lower resistance and inductances. Components should be placed to minimize connecting paths. Careful attention to ground connections must also be maintained. Without getting into elaborate detail be careful that currents from different high current loops do not get coupled into B CIN A 1 3 D 2 4 C GATE A COUT GATE B CS 1683 F08 Figure 8 1683fd 22 LT1683 TYPICAL APPLICATIONS Ultralow Noise 48V to 12V DC/DC Converter 10k 48V 510 0.5W D1 47F 100V FZT853 D2 C4 22F 50V D3 12V C3 10F 25V 2N3904 5 6 7 16.9k 8 25k 3.3k 16 25k 3.3k 15 1k 12 0.22F 6 2 8.2V 17 VIN 14 1200pF MBR01100 10 D4 D5 23.2k 976 CTX0215542 T1 1 SHDN CAP A V5 GATE A SYNC CT CAP B LT1683 RT GATE B RVSL CS RCSL PGND VC 22nF SS 10nF 13 3,4 3 GCL GND 11 FB NFB 2 5pF 5pF 200V 8,9 D6 5 7 1 18 5pF 200V 5pF 25pF 19 4 Si9422 D7 L1 10H 12V/1A C1 33F 16V, x2 C2 33F 16V, x2 L2 10H -12V/1A 10.0k 2.74k Si9422 0.068 20 8.66k 9 25pF 1k 10 C1, C2:SANYO 16TPC33 C3: MURATA GRM235Y5V106Z C4: NIPPON THCR60EIE226Z D1, D2, D3 IN4148 D4, D5, D6, D7 MBRS1100 L1, L2: COOPER DS50224 T1: COOPER CTX02-15542 1683 TA03 1683fd 23 LT1683 PACKAGE DESCRIPTION G Package 20-Lead Plastic SSOP (5.3mm) (Reference LTC DWG # 05-08-1640) 6.90 - 7.50* (.272 - .295 ) 20 19 18 17 16 15 14 13 12 11 1.25 0.12 7.8 - 8.2 5.3 - 5.7 7.40 - 8.20 (.291 - .323) 0.42 0.03 0.65 BSC RECOMMENDED SOLDER PAD LAYOUT 1 2 3 4 5 6 7 8 9 10 5.00 - 5.60** (.197 - .221) 2.0 (.079) MAX 0-8 0.09 - 0.25 (.0035 - .010) 0.55 - 0.95 (.022 - .037) NOTE: 1. CONTROLLING DIMENSION: MILLIMETERS MILLIMETERS 2. DIMENSIONS ARE IN (INCHES) 0.65 (.0256) BSC 0.22 - 0.38 (.009 - .015) TYP 0.05 (.002) MIN G20 SSOP 0204 3. DRAWING NOT TO SCALE *DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED .152mm (.006") PER SIDE **DIMENSIONS DO NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED .254mm (.010") PER SIDE 1683fd 24 LT1683 REVISION HISTORY (Revision history begins at Rev D) REV DATE DESCRIPTION PAGE NUMBER D 11/10 Updated Max Switch Frequency to 150kHz in the Electrical Characteristics section 3 1683fd Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 25 LT1683 TYPICAL APPLICATION Ultralow Noise 24V to 5V DC/DC Converter COILTRONICS VP5-1200 24V 6.9k 39F 2N3904 11V 8.2V 68F 20V 17 VIN 14 5 6 1.5nF 7 16.9k 8 25k 3.3k 16 25k 3.3k 15 1k 15nF 12 SHDN V5 GATE A SYNC CT CAP B LT1683 RT GATE B RVSL CS RCSL PGND VC 1nF SS GND 13 7 6-10 3 11 2-12 3pF 1 3 GCL CAP A FB NFB 11 OPTIONAL MBR2045CT 2 10pF 1 1H 5V/5A 9 330F 4 8 5 2x330F POSCAP CAP A MBR2045CT GATE A 3pF 18 CAP B 10pF 19 4 4.7H IRF540 GATE B IRF540 20 10m 7.50k 9 2.49k 10 10nF 1683 TA02 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT1533 Ultralow Noise 1A Switching Regulator Push-Pull Design for Low Noise Isolated Supplies LT1534 Ultralow Noise 2A Switching Regulator Ultralow Noise Regulator for Boost Topologies LT1738 Ultralow Noise DC/DC Controller High Current Output Ultralow Noise Boost Regulator; Drives External MOSFET LT1777 Low Noise Step-Down Switching Regulator Programmable dI/dt; Internally Limited dV/dt LT1425 Isolated Flyback Switching Regulator Excellent Regulation without Transformer "Third Winding" LT1576 1.5A, 200kHz Step-Down Switching Regulator Constant Frequency, 1.21V Reference Voltage LT176X Family Low Dropout, Low Noise Linear Regulator 150mA to 3A, SOT-23 to TO-220 LTC1922-1/LTC3722 Synchronous Phase Modulated Full-Bridge Controllers Adaptive DirectSenseTM Zero Voltage Switching, 50W to Kilowatts, Synchronous Rectification LT3439 Ultralow Noise Transformer Driver 1A Push-Pull DC/DC Transformer Driver 1683fd 26 Linear Technology Corporation LT 1110 REV D * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com LINEAR TECHNOLOGY CORPORATION 2001