1
Data sheet acquired from Harris Semiconductor
SCHS123E
Features
Retriggerable/Resettable Capability
Trigger and Reset Propagation Delays Independent of
RX, CX
Triggering from the Leading or Trailing Edge
Q and Q Buffered Outputs Available
Separate Resets
Wide Range of Output Pulse Widths
Schmitt Trigger Input on A and B Inputs
Retrigger Time is Independent of CX
Fanout (Over Temperature Range)
- Standard Outputs. . . . . . . . . . . . . . . 10 LSTTL Loads
- Bus Driver Outputs . . . . . . . . . . . . . 15 LSTTL Loads
Wide Operating T emperature Range . . . -55oC to 125oC
Balanced Propagation Delay and Transition Times
Significant Power Reduction Compared to LSTTL
Logic ICs
HC Types
- 2V to 6V Operation
- High Noise Immunity: NIL = 30%, NIH = 30% of VCC
at VCC = 5V
HCT Types
- 4.5V to 5.5V Operation
- Direct LSTTL Input Logic Compatibility,
VIL= 0.8V (Max), VIH = 2V (Min)
- CMOS Input Compatibility, Il1µA at VOL, VOH
Pinout CD54HC4538, CD54HCT4538
(CERDIP)
CD74HC4538
(PDIP, SOIC, SOP, TSSOP)
CD74HCT4538
(PDIP, SOIC)
TOP VIEW
Description
The ’HC4538 and ’HCT4538 are dual
retriggerable/resettable monostable precision multivibrators
for fixed voltage timing applications. An external resistor
(RX) and an external capacitor (CX) control the timing and
the accuracy for the circuit. Adjustment of RXand CX
provides a wide range of output pulse widths from the Q and
Q terminals. The propagation delay from trigger input-to-
output transition and the propagation delay from reset input-
to-output transition are independent of RX and CX.
Leading-edge triggering (A) and trailing edge triggering (B)
inputs are provided for triggering from either edge of the
input pulse. An unused “A” input should be tied to GND and
an unused B should be tied to VCC. On power up the IC is
reset. Unused resets and sections must be terminated. In
normal operation the circuit retriggers on the application of
each new trigger pulse. To operate in the non-triggerable
mode Q is connected to B when leading edge triggering (A)
is used or Q is connected to A when trailing edge triggering
(B) is used. The period (τ) can be calculated from τ= (0.7)
RX, CX; RMIN is 5k. CMIN is 0pF.
14
15
16
9
13
12
11
10
1
2
3
4
5
7
6
8
1C
X
1R
X
C
X
1R
1A
1B
1Q
GND
1Q
V
CC
2R
X
C
X
2R
2A
2B
2Q
2Q
2C
X
Ordering Information
PART NUMBER TEMP. RANGE
(oC) PACKAGE
CD54HC4538F3A -55 to 125 16 Ld CERDIP
CD54HCT4538F3A -55 to 125 16 Ld CERDIP
CD74HC4538E -55 to 125 16 Ld PDIP
CD74HC4538M -55 to 125 16 Ld SOIC
CD74HC4538MT -55 to 125 16 Ld SOIC
CD74HC4538M96 -55 to 125 16 Ld SOIC
CD74HC4538NSR -55 to 125 16 Ld SOP
CD74HC4538PW -55 to 125 16 Ld TSSOP
CD74HC4538PWR -55 to 125 16 Ld TSSOP
CD74HC4538PWT -55 to 125 16 Ld TSSOP
CD74HCT4538E -55 to 125 16 Ld PDIP
CD74HCT4538M -55 to 125 16 Ld SOIC
CD74HCT4538MT -55 to 125 16 Ld SOIC
CD74HCT4538M96 -55 to 125 16 Ld SOIC
NOTE: When ordering, use the entire part number. The suffixes 96
and R denote tape and reel. The suffix T denotes a small-quantity
reel of 250.
CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures.
Copyright © 2003, Texas Instruments Incorporated
CD54HC4538, CD74HC4538,
CD54HCT4538, CD74HCT4538
High-Speed CMOS Logic Dual Retriggerable
Precision Monostable Multivibrator
[
/Title
(
CD54
H
C453
8
,
C
D74
H
C453
8
,
C
D74
H
CT45
3
8)
/
Sub-
j
ect
(
High
S
peed
C
MOS
L
ogic
June 1998 - Revised October 2003
2
Functional Diagram
2R 13
2A 12
11
10
92Q
2Q
2B MONO 2
VCC
15 14
2Cx 2RxCx
1R 3
1A
5
46
71Q
1Q
1B
MONO 1
VCC
12
1Cx 1RxCx
1Cx 1Rx
2Cx 2Rx
GND = 8
VCC = 16
TRUTH TABLE
INPUTS OUTPUTS
RABQQ
LXXLH
XHXLH
XXLLH
HL
HH
H = High Level, L = Low Level, = Transition from Low to High,
= Transition from High to Low, One High Level Pulse,
One Low Level Pulse, X = Irrelevant. FIGURE 1. FF DETAIL
CL
CL
CL
CL
p
np
n
p
n
CL
R1
R2
CL
R1
Q
Q
CL
D
CD54HC4538, CD74HC4538, CD54HCT4538, CD74HCT4538
3
FIGURE 2. LOGIC DIAGRAM (1 MONO)
FUNCTIONAL TERMINAL CONNECTIONS
FUNCTION
VCC TO
TERMINAL NUMBER GND TO
TERMINAL NUMBER INPUT PULSE TO
TERMINAL NUMBER OTHER
CONNECTIONS
MONO1MONO2MONO1MONO2MONO1MONO2MONO1MONO2
Leading-Edge
Trigger/Retriggerable 3, 5 11, 13 4 12
Leading-Edge
Trigger/Non-Retriggerable 3 13 4 12 5-7 11-9
Trailing-Edge
Trigger/Retriggerable 313412511
Trailing-Edge
Trigger/Non-Retriggerable 3 13 5 11 4-6 12-10
NOTES:
1. A retriggerable one-shot multivibrator has an output pulse width which is extended one full time period (T) after application of the last
trigger pulse.
2. A non-triggerable one-shot multivibrator has a time period (T) referenced from the application of the first trigger pulse.
FIGURE 3. INPUT PULSE TRAIN FIGURE 4. RETRIGGERABLE MODE
PULSE WIDTH (A MODE) FIGURE5. NON-RETRIGGERABLEMODE
PULSE WIDTH
(A MODE)
D
CL CL Q
Q
R2R1 FF
VCC
VCC
RX
CX
2(14)
1(15)
8
R
A
B
3(13)
4(12)
5(11)
VCC
VCC
HIGH Z
VCC
VCC
R1
R2
COMP II
-
+6(10)
7(9)
Q
Q
VCC
16
TT
CD54HC4538, CD74HC4538, CD54HCT4538, CD74HCT4538
4
Absolute Maximum Ratings Thermal Information
DC Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 7V
DC Input Diode Current, IIK
For VI < -0.5V or VI > VCC + 0.5V. . . . . . . . . . . . . . . . . . . . . .±20mA
DC Output Diode Current, IOK
For VO < -0.5V or VO > VCC + 0.5V . . . . . . . . . . . . . . . . . . . .±20mA
DC Output Source or Sink Current per Output Pin, IO
For VO > -0.5V or VO < VCC + 0.5V . . . . . . . . . . . . . . . . . . . .±25mA
DC VCC or Ground Current, ICC . . . . . . . . . . . . . . . . . . . . . . . . .±50mA
Operating Conditions
Temperature Range, TA . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC
Supply Voltage Range, VCC (Note 3)
HC Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2V to 6V
HCT Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.5V to 5.5V
DC Input or Output Voltage, VI, VO . . . . . . . . . . . . . . . . . 0V to VCC
Input Rise and Fall Times, tr, tf
Reset Input:
2V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000ns (Max)
4.5V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500ns (Max)
6V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400ns (Max)
Trigger Inputs A or B:
2V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Unlimited (Max)
4.5V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Unlimited (Max)
6V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Unlimited (Max)
External Timing Resistor, RX (Note 4) . . . . . . . . . . . . . . . .5k (Min)
External Timing Capacitor, CX (Note 4) . . . . . . . . . . . . . . . . .0 (Min)
Package Thermal Impedance, θJA (see Note 5):
E (PDIP) Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67oC/W
M (SOIC) Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73oC/W
NS (SOP) Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64oC/W
PW (TSSOP) Package . . . . . . . . . . . . . . . . . . . . . . . . . 108oC/W
Maximum Junction Temperature. . . . . . . . . . . . . . . . . . . . . . . 150oC
Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC
Maximum Lead Temperature (Soldering 10s). . . . . . . . . . . . .300oC
(SOIC - Lead Tips Only)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
3. Unless otherwise specified, all voltages are referenced to ground.
4. The maximum allowable values of RXand CXare a function of leakage of capacitor CX, the leakage of the ’HC4538, and leakage due to
board layout and surface resistance. Values of RXand CXshould be chosen so that the maximum current into pin 2 or pin 14 is 30mA.
Susceptibility to externally induced noise signals may occur for RX > 1M.
5. The package thermal impedance is calculated in accordance with JESD 51-7.
DC Electrical Specifications
PARAMETER SYMBOL
TEST
CONDITIONS VCC
(V)
25oC -40oC TO 85oC -55oC TO 125oC
UNITSVI(V) IO(mA) MIN TYP MAX MIN MAX MIN MAX
HC TYPES
High Level Input
Voltage VIH - - 2 1.5 - - 1.5 - 1.5 - V
4.5 3.15 - - 3.15 - 3.15 - V
6 4.2 - - 4.2 - 4.2 - V
Low Level Input
Voltage VIL - - 2 - - 0.5 - 0.5 - 0.5 V
4.5 - - 1.35 - 1.35 - 1.35 V
6 - - 1.8 - 1.8 - 1.8 V
High Level Output
Voltage
CMOS Loads
VOH VIH or VIL -0.02 2 1.9 - - 1.9 - 1.9 - V
-0.02 4.5 4.4 - - 4.4 - 4.4 - V
-0.02 6 5.9 - - 5.9 - 5.9 - V
High Level Output
Voltage
TTL Loads
- - ---- - - -V
-4 4.5 3.98 - - 3.84 - 3.7 - V
-5.2 6 5.48 - - 5.34 - 5.2 - V
CD54HC4538, CD74HC4538, CD54HCT4538, CD74HCT4538
5
Low Level Output
Voltage
CMOS Loads
VOL VIH or VIL 0.02 2 - - 0.1 - 0.1 - 0.1 V
0.02 4.5 - - 0.1 - 0.1 - 0.1 V
0.02 6 - - 0.1 - 0.1 - 0.1 V
Low Level Output
Voltage
TTL Loads
- - ---- - - -V
4 4.5 - - 0.26 - 0.33 - 0.4 V
5.2 6 - - 0.26 - 0.33 - 0.4 V
Input Leakage
Current A, B, R IIVCC or
GND -6--±0.1 - ±1-±1µA
Input Leakage
Current RXCX
(Note 6)
-6--±0.05 - ±0.5 - ±0.5 µA
Quiescent Device
Current ICC VCC or
GND 0 6 - - 8 - 80 - 160 µA
Active Device Current
Q = High & Pins 2, 14
at VCC/4
ICC VCC or
GND 0 6 - - 0.6 - 0.8 - 1 mA
HCT TYPES
High Level Input
Voltage VIH - - 4.5 to
5.5 2--2 - 2 - V
Low Level Input
Voltage VIL - - 4.5 to
5.5 - - 0.8 - 0.8 - 0.8 V
High Level Output
Voltage
CMOS Loads
VOH VIH or VIL -0.02 4.5 4.4 - - 4.4 - 4.4 - V
High Level Output
Voltage
TTL Loads
-4 4.5 3.98 - - 3.84 - 3.7 - V
Low Level Output
Voltage
CMOS Loads
VOL VIH or VIL 0.02 4.5 - - 0.1 - 0.1 - 0.1 V
Low Level Output
Voltage
TTL Loads
4 4.5 - - 0.26 - 0.33 - 0.4 V
Input Leakage
Current IIVCC and
GND - 5.5 - ±0.1 - ±1-±1µA
Input Leakage
Current RXCX
(Note 6)
- 5.5 - - ±0.05 - ±0.5 - ±0.5 µA
Quiescent Device
Current ICC VCC or
GND 0 5.5 - - 8 - 80 - 160 µA
Active Device Current
Q = High & Pins 2, 14
at VCC/4
ICC VCC or
GND 0 5.5 - - 0.6 - 0.8 - 1 mA
Additional Quiescent
Device Current Per
Input Pin: 1 Unit Load
ICC
(Note 7) VCC
-2.1 - 4.5 to
5.5 - 100 360 - 450 - 490 µA
NOTES:
6. When testing IIL the Q output must be high. If Q is low (device not triggered) the pull-up P device will be ON and the low resistance path
from VDD to the test pin will cause a current far exceeding the specification.
7. For dual-supply systems theoretical worst case (VI = 2.4V, VCC = 5.5V) specification is 1.8mA.
DC Electrical Specifications (Continued)
PARAMETER SYMBOL
TEST
CONDITIONS VCC
(V)
25oC -40oC TO 85oC -55oC TO 125oC
UNITSVI(V) IO(mA) MIN TYP MAX MIN MAX MIN MAX
CD54HC4538, CD74HC4538, CD54HCT4538, CD74HCT4538
6
HCT Input Loading Table
INPUT UNIT LOADS
All 0.5
NOTE: Unit Load is ICC limit specified in DC Electrical Table, e.g.
360µA max at 25oC.
Prerequisite for Switching Specifications
PARAMETER SYMBOL VCC (V)
25oC -40oC TO 85oC -55oC TO 125oC
UNITSMIN TYP MAX MIN TYP MAX MIN TYP MAX
HC TYPES
Input Pulse Widths tWH, tWL
A, B 2 80 - - 100 - - 120 - - ns
4.5 16 - - 20 - - 24 - - ns
614--17- -20--ns
Rt
WL 2 80 - - 100 - - 120 - - ns
4.5 16 - - 20 - - 24 - - ns
614--17- -20--ns
Reset Recovery Time tREC 25--5--5--ns
4.5 5 - - 5 - - 5 - - ns
65--5--5--ns
Retrigger Time
(Figure 11) trT 5 - 175 - - - - - - - ns
HCT TYPES
Input Pulse Widths tWH, tWL
A, B 4.5 16 - - 20 - - 24 - - ns
Rt
WL 4.5 20 - - 25 - - 30 - - ns
Reset Recovery Time tREC 4.5 5 - - 5 - - 5 - - ns
Retrigger Time
(Figure 11) trT 5 - 175 - - - - - - - ns
CD54HC4538, CD74HC4538, CD54HCT4538, CD74HCT4538
7
Switching Specifications CL = 50pF, Input tr, tf= 6ns, RX = 10K, CX = 0
PARAMETER SYMBOL TEST
CONDITIONS VCC (V)
25oC-40oC TO
85oC-55oC TO
125oC
UNITSMIN TYP MAX MIN MAX MIN MAX
HC TYPES
Propagation Delay tPLH CL = 50pF
A, B to Q 2 - - 250 - 315 - 375 ns
4.5 - - 50 - 63 - 75 ns
CL = 15pF 5 - 21 - - - - - ns
CL = 50pF 6 - - 43 - 54 - 64 ns
A, B to Qt
PHL CL = 50pF 2 - - 250 - 315 - 375 ns
4.5 - - 50 - 63 - 75 ns
CL = 15pF 5 - 21 - - - - - ns
CL = 50pF 6 - - 43 - 54 - 64 ns
R to Q tPHL CL = 50pF 2 - - 250 - 315 - 375 ns
4.5 - - 50 - 63 - 75 ns
CL = 15pF 5 - 21 - - - - - ns
CL = 50pF 6 - - 43 - 54 - 64 ns
R to Qt
PLH CL = 50pF 2 - - 250 - 315 - 375 ns
4.5 - - 50 - 63 - 75 ns
CL = 15pF 5 - 21 - - - - - ns
CL = 50pF 6 - - 43 - 54 - 64 ns
Output Transition Time tTLH, tTHL CL = 50pF 2 - - 75 - 95 - 110 ns
4.5 - - 15 - 19 - 22 ns
6 - - 13 - 16 - 19 ns
Output Pulse Width
RX = 10k, CX = 0.1µFτCL = 50pF 3 0.64 - 0.78 0.612 0.812 0.605 0.819 ms
5 0.63 - 0.77 0.602 0.798 0.595 0.805 ms
Output Pulse Width Match,
Same Package -- -±1- - - - - %
Power Dissipation Capacitance
(Notes 8, 9) CPD CL = 15pF 5 - 136 - - - - - pF
Input Capacitance CICL = 50pF - 10 - 10 - 10 - 10 pF
HCT TYPES
Propagation Delay tPLH
A, B to Q CL = 50pF 4.5 - - 55 - 69 - 83 ns
CL = 15pF 5 - 23 - - - - - ns
A, B to Qt
PHL CL = 50pF 4.5 - - 55 - 69 - 83 ns
CL = 15pF 5 - 23 - - - - - ns
CD54HC4538, CD74HC4538, CD54HCT4538, CD74HCT4538
8
R to Q tPHL CL = 50pF 4.5 - - 40 - 50 - 60 ns
CL = 15pF 5 - 17 - - - - - ns
R to Qt
PLH CL = 50pF 4.5 - - 50 - 63 - 75 ns
CL = 15pF 5 - 21 - - - - - ns
Output Transition Time tTLH, tTHL CL = 50pF 4.5 - - 15 - 19 - 22 ns
Output Pulse Width
RX = 10k, CX = 0.1µFτCL = 50pF 5 0.63 - 0.77 0.602 0.798 0.595 0.805 ms
Output Pulse Width Match,
Same Package ----±1- - - - - %
Power Dissipation Capacitance
(Notes 8, 9) CPD CL = 15pF 5 - 134 - - - - - pF
Input Capacitance CICL = 50pF - 10 - 10 - 10 - 10 pF
NOTES:
8. CPD is used to determine the dynamic power consumption, per one shot.
9. PD=(C
PD +C
X)V
CC2fi(CLVCC2fO) where fi= input frequency, fO= output frequency, CL= output load capacitance,
CX = external capacitance VCC = supply voltage assuming fi «
Switching Specifications CL = 50pF, Input tr, tf= 6ns, RX = 10K, CX = 0 (Continued)
PARAMETER SYMBOL TEST
CONDITIONS VCC (V)
25oC-40oC TO
85oC-55oC TO
125oC
UNITSMIN TYP MAX MIN MAX MIN MAX
I
τ
--
Test Circuits and Waveforms
FIGURE 6. HC AND HCU TRANSITION TIMES AND PROPAGA-
TION DELAY TIMES, COMBINATION LOGIC FIGURE 7. HCT TRANSITION TIMES AND PROPAGATION
DELAY TIMES, COMBINATION LOGIC
tPHL tPLH
tTHL tTLH
90%
50%
10%
50%
10%
INVERTING
OUTPUT
INPUT
GND
VCC
tr = 6ns tf = 6ns
90%
tPHL tPLH
tTHL tTLH
2.7V
1.3V
0.3V
1.3V
10%
INVERTING
OUTPUT
INPUT
GND
3V
tr = 6ns tf = 6ns
90%
CD54HC4538, CD74HC4538, CD54HCT4538, CD74HCT4538
9
Typical Performance Curves
FIGURE 8. K FACTOR vs DC SUPPLY VOLTAGE (VCC) - V FIGURE 9. K FACTOR vs DC SUPPLY VOLTAGE (VCC) - V
FIGURE 10. K FACTOR vs CXFIGURE 11. MINIMUM RETRIGGER TIME vs TIMING
CAPACITANCE
0.70
0.69
0.68
0.67
2 3 4 4.5 5 5.5 6
VCC, DC SUPPLY VOLTAGE (V)
K FACTOR
10k, 10nF
10k, 100nF
100k, 100nF
100k, 10nF
HC4538 - TA11646C
TA = 25oC0.70
0.69
0.68
0.67
2 3 4 4.5 5 5.5 6
VCC, DC SUPPLY VOLTAGE (V)
K FACTOR
10k, 10nF
10k, 100nF
100k, 100nF
100k, 10nF
HCT4538 - TA13646C
TA = 25oC
1.3
1.1
0.9
0.6
10 102103104105
CX, TIMING CAPACITANCE (pF)
K FACTOR
2k
10k
100k
HC/HCT4538
VCC = 5V, TA = 25oC
1.2
1.0
0.8
0.7
104
102
10 102103104
CX, TIMING CAPACITANCE (pF)
trr, TYP MIN RETRIGGER TIME (ns)
VCC = 4.5V
TA = 25oC
RX = 10k
103
VCC = 5V
CD54HC4538, CD74HC4538, CD54HCT4538, CD74HCT4538
10
Power-Down Mode
During a rapid power-down condition, as would occur with a
power-supply short circuit with a poorly filtered power supply,
the energy stored in CXcould discharge into Pin 2 or 14. To
aviod possible device damage in this mode, when CXis
0.5µF, a protection diode with a 1 ampere or higher rating
(1N5395 or equivalent) and a separate ground return for CX
should be provided as shown in Figure 12.
An alternate protection method is shown in Figure 13, where
a51current-limiting resistor is inserted in series with CX.
Note that a small pulse width decrease will occur however,
and RXmust be appropriately increased to obtain the origi-
nally desired pulse width.
FIGURE 12. RAPID POWER-DOWN PROTECTION CIRCUIT
IN5395
OR
EQUIVALENT RX
CX
0.5µF
1(15)
2(14)
VCC
16
8
+
FIGURE 13. ALTERNATE RAPID POWER-DOWN PROTECTION
CIRCUIT
RX
CX
0.5µF1(15)
2(14)
VCC
16
8
51
CD54HC4538, CD74HC4538, CD54HCT4538, CD74HCT4538
PACKAGING INFORMATION
Orderable Device Status (1) Package
Type Package
Drawing Pins Package
Qty Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
5962-8688601EA ACTIVE CDIP J 16 1 TBD A42 N / A for Pkg Type
CD54HC4538F ACTIVE CDIP J 16 1 TBD A42 N / A for Pkg Type
CD54HC4538F3A ACTIVE CDIP J 16 1 TBD A42 N / A for Pkg Type
CD54HCT4538F3A ACTIVE CDIP J 16 1 TBD A42 N / A for Pkg Type
CD74HC4538E ACTIVE PDIP N 16 25 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type
CD74HC4538EE4 ACTIVE PDIP N 16 25 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type
CD74HC4538M ACTIVE SOIC D 16 40 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
CD74HC4538M96 ACTIVE SOIC D 16 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
CD74HC4538M96E4 ACTIVE SOIC D 16 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
CD74HC4538M96G4 ACTIVE SOIC D 16 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
CD74HC4538ME4 ACTIVE SOIC D 16 40 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
CD74HC4538MG4 ACTIVE SOIC D 16 40 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
CD74HC4538MT ACTIVE SOIC D 16 250 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
CD74HC4538MTE4 ACTIVE SOIC D 16 250 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
CD74HC4538MTG4 ACTIVE SOIC D 16 250 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
CD74HC4538NSR ACTIVE SO NS 16 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
CD74HC4538NSRE4 ACTIVE SO NS 16 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
CD74HC4538NSRG4 ACTIVE SO NS 16 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
CD74HC4538PW ACTIVE TSSOP PW 16 90 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
CD74HC4538PWE4 ACTIVE TSSOP PW 16 90 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
CD74HC4538PWG4 ACTIVE TSSOP PW 16 90 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
CD74HC4538PWR ACTIVE TSSOP PW 16 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
CD74HC4538PWRE4 ACTIVE TSSOP PW 16 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
CD74HC4538PWRG4 ACTIVE TSSOP PW 16 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
CD74HC4538PWT ACTIVE TSSOP PW 16 250 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
CD74HC4538PWTE4 ACTIVE TSSOP PW 16 250 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
CD74HC4538PWTG4 ACTIVE TSSOP PW 16 250 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
PACKAGE OPTION ADDENDUM
www.ti.com 15-Oct-2009
Addendum-Page 1
Orderable Device Status (1) Package
Type Package
Drawing Pins Package
Qty Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
no Sb/Br)
CD74HCT4538E ACTIVE PDIP N 16 25 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type
CD74HCT4538EE4 ACTIVE PDIP N 16 25 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type
CD74HCT4538M ACTIVE SOIC D 16 40 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
CD74HCT4538M96 ACTIVE SOIC D 16 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
CD74HCT4538M96E4 ACTIVE SOIC D 16 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
CD74HCT4538M96G4 ACTIVE SOIC D 16 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
CD74HCT4538ME4 ACTIVE SOIC D 16 40 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
CD74HCT4538MG4 ACTIVE SOIC D 16 40 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
CD74HCT4538MT ACTIVE SOIC D 16 250 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
CD74HCT4538MTE4 ACTIVE SOIC D 16 250 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
CD74HCT4538MTG4 ACTIVE SOIC D 16 250 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
PACKAGE OPTION ADDENDUM
www.ti.com 15-Oct-2009
Addendum-Page 2
OTHER QUALIFIED VERSIONS OF CD54HC4538, CD54HCT4538, CD74HC4538, CD74HCT4538 :
Automotive: CD74HC4538-Q1
NOTE: Qualified Version Definitions:
Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
PACKAGE OPTION ADDENDUM
www.ti.com 15-Oct-2009
Addendum-Page 3
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0 (mm) B0 (mm) K0 (mm) P1
(mm) W
(mm) Pin1
Quadrant
CD74HC4538M96 SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1
CD74HC4538NSR SO NS 16 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.0 Q1
CD74HC4538PWR TSSOP PW 16 2000 330.0 12.4 7.0 5.6 1.6 8.0 12.0 Q1
CD74HCT4538M96 SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 19-Mar-2008
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
CD74HC4538M96 SOIC D 16 2500 333.2 345.9 28.6
CD74HC4538NSR SO NS 16 2000 346.0 346.0 33.0
CD74HC4538PWR TSSOP PW 16 2000 346.0 346.0 29.0
CD74HCT4538M96 SOIC D 16 2500 333.2 345.9 28.6
PACKAGE MATERIALS INFORMATION
www.ti.com 19-Mar-2008
Pack Materials-Page 2
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,65 M
0,10
0,10
0,25
0,50
0,75
0,15 NOM
Gage Plane
28
9,80
9,60
24
7,90
7,70
2016
6,60
6,40
4040064/F 01/97
0,30
6,60
6,20
80,19
4,30
4,50
7
0,15
14
A
1
1,20 MAX
14
5,10
4,90
8
3,10
2,90
A MAX
A MIN
DIM PINS **
0,05
4,90
5,10
Seating Plane
0°–8°
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-153
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,and other changes to its products and services at any time and to discontinue any product or service without notice. Customers shouldobtain the latest relevant information before placing orders and should verify that such information is current and complete. All products aresold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standardwarranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except wheremandated by government requirements, testing of all parameters of each product is not necessarily performed.TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products andapplications using TI components. To minimize the risks associated with customer products and applications, customers should provideadequate design and operating safeguards.TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Informationpublished by TI regarding third-party products or services does not constitute a license from TI to use such products or services or awarranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectualproperty of the third party, or a license from TI under the patents or other intellectual property of TI.Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompaniedby all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptivebusiness practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additionalrestrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids allexpress and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is notresponsible or liable for any such statements.TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonablybe expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governingsuch use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, andacknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their productsand any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may beprovided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products insuch safety-critical applications.TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products arespecifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet militaryspecifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely atthe Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products aredesignated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designatedproducts in automotive applications, TI will not be responsible for any failure to meet such requirements.Following are URLs where you can obtain information on other Texas Instruments products and application solutions:Products ApplicationsAmplifiers amplifier.ti.com Audio www.ti.com/audioData Converters dataconverter.ti.com Automotive www.ti.com/automotiveDLP® Products www.dlp.com Broadband www.ti.com/broadbandDSP dsp.ti.com Digital Control www.ti.com/digitalcontrolClocks and Timers www.ti.com/clocks Medical www.ti.com/medicalInterface interface.ti.com Military www.ti.com/militaryLogic logic.ti.com Optical Networking www.ti.com/opticalnetworkPower Mgmt power.ti.com Security www.ti.com/securityMicrocontrollers microcontroller.ti.com Telephony www.ti.com/telephonyRFID www.ti-rfid.com Video & Imaging www.ti.com/videoRF/IF and ZigBee® Solutions www.ti.com/lprf Wireless www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265Copyright © 2009, Texas Instruments Incorporated