05135 SLVU2.8 Only One Name Means ProTek'TionTM 600 WATT ULTRA LOW CAPACITANCE TVS ARRAY Description The SLVU2.8 is a low voltage, low leakage current and ultra low capacitance TVS device designed for EOS and ESD protection of low voltage circuits commonly found in network and computing applications. This device can be placed at the connector input or at the sensitive IC component and also be used across a single ended data line for the protection of a single line. The SLVU2.8 device meets the IEC requirements of 61000-4-2 (ESD), 61000-4-4 (EFT) and 61000-4-5 (Surge). This device has a peak pulse power rating of 600 Watts (8/20s waveform) and is available in a SOT-23 package configuration. sot-23 package Features applications * Compatible with IEC 61000-4-2 (ESD): Air 15kV, Contact 8kV * Compatible with IEC 61000-4-4 (EFT): 40A, 5/50ns * Compatible with IEC 61000-4-5 (Surge): 24A, 8/20s - Level 2(LineGround) & Level 3(Line-Line) * ESD Protection > 25 kilovolts * 600 Watts Peak Pulse Power per Line(tp = 8/20s) * Unidirectional Configuration * Protects 1 Line * Low Leakage Current < 1.0A * Ultra Low Capacitance: 2.5pF * RoHS Compliant * REACH Compliant * * * * Ethernet 10/100/1000 Base T Routers and Switches Audio/Video Inputs Portable Electronics mechaniCal characteristics * Molded JEDEC SOT-23 Package * Approximate Weight: 8 milligrams * Lead-Free Pure-Tin Plating (Annealed) * Solder Reflow Temperature: Pure-Tin - Sn, 100: 260-270C * Flammability Rating UL 94V-0 * 8mm Tape and Reel per EIA Standard 481 PIN CONFIGURATION 1 3 2 05135.R11 10/12 Page 1 www.protekdevices.com 05135 SLVU2.8 Only One Name Means ProTek'TionTM typical device characteristics MAXIMUM RATINGS @ 25C Unless Otherwise Specified PARAMETER SYMBOL VALUE UNITS PPP 600 Watts Peak Pulse Power (tp = 8/20s) - See Figure 1 Peak Pulse Current (tp = 8/20s) IPP 30 Amps Repetitive Peak Forward Current @ tp = 5s, F=50kHz, Pin 2 to 3 IFRM 700 mA TL -55 to 150 C TSTG -55 to 150 C Operating Temperature Storage Temperature ELECTRICAL CHARACTERISTICS PER LINE @ 25C Unless Otherwise Specified PART NUMBER (Note 1) SLVU2.8 device marking SLA RATED STAND-OFF VOLTAGE MINIMUM BREAKDOWN VOLTAGE MINIMUM SNAP BACK VOLTAGE @ I SB = 50mA VSB VOLTS MAXIMUM CLAMPING VOLTAGE (Fig. 2) @ IP = 2A VC VOLTS MAXIMUM CLAMPING VOLTAGE (Fig. 2) @ IP = 5A VC VOLTS MAXIMUM CLAMPING VOLTAGE (Fig. 2) @ IP = 30A VC VOLTS VWM VOLTS @ 1mA V(BR) VOLTS 2.8 3.0 2.8 3.9 7.0 21.0 MAXIMUM FORWARD VOLTAGE Pin 2 to 3 (Note 1) @IF = 1A TP = 120s VF VOLTS 2 NOTES 1. Device measured from pin 3 to 1. ELECTRICAL CHARACTERISTICS PER LINE @ 25C Unless Otherwise Specified MAXIMUM CLAMPING VOLTAGE Pin 2 to 1 (Fig. 2) typical CLAMPING VOLTAGE Pin 2 to 1 (Fig. 2) maximum leakage current Pin 3 to 1 or Pin 2 to 1 TYPICAL CAPACITANCE Pin 3 to 1 & 2 (Tied Together) TYPICAL CAPACITANCE Pin 2 to 1 3 N.C. MAXIMUM PEAK REVERSE VOLTAGE Pin 3 to 2 (Note 1) @ I P = 5A VC VOLTS @ I P = 30A VC VOLTS @VWM ID A @0V, 1MHz C pF @0V, 1MHz C pF @IT = 10A VRRM VOLTS MAXIMUM REVERSE leakage VOLTAGE Pin 3 to 2 (Note 1) @VWM = 2.8V IDR A 8.5 21.0 1.0 20 2.5 40 0.1 NOTES 1. Electrical characteristics for steering diodes. 05135.R11 10/12 Page 2 www.protekdevices.com 05135 SLVU2.8 Only One Name Means ProTek'TionTM typical device characteristics figure 1 peak pulse power vs pulse time PPP - Peak Pulse Power - Watts 10,000 1,000 600W, 8/20s Waveform 100 10 0.1 1 10 100 td - Pulse Duration - s IPP - Peak Pulse Current - % of IPP 10,000 figure 2 pulse wave form 120 tf 100 TEST WAVEFORM PARAMETERS tf = 8s td = 20s Peak Value IPP 80 e-t 60 40 td = t/(IPP/2) 20 0 05135.R11 10/12 1,000 0 5 10 15 t - Time - s Page 3 20 25 30 www.protekdevices.com 05135 SLVU2.8 Only One Name Means ProTek'TionTM typical device characteristics 100 figure 3 power derating curve Peak Pulse Power 8/20s % Of Rated Power 80 60 40 20 0 Average Power 0 25 50 75 100 125 TA - Ambient Temperature - C 150 figure 4 typical clamping voltage vs peak pulse current 20 Pin 2 to 1 VC - Clamping Voltage - V 16 12 8 4 0 0 05135.R11 10/12 Pin 3 to 1 5 10 15 20 IPP - Peak Pulse Current - Amps Page 4 25 30 www.protekdevices.com 05135 SLVU2.8 Only One Name Means ProTek'TionTM SPICE MODEL figure 1 spice model Pin 3 Pin 2 I/O LCABD I/O LCRD LCABD LCRD OR Lg 0.6nH Lg 0.6nH Pin 1, 2 Pin 1 LCABD - Low Capacitance Avalanche Breakdown Diode (TVS) LCRD: Low Capacitance Rectifier Diode Lg - Lead Inductance table 1 - spice parameters parameter 05135.R11 10/12 unit abd(tvs) lcrd BV V 3.3 200 IBV A 1 0.01 Cjo pF 20 5 IS A 1E-11 1E-13 Vj V - 0.6 M - 0.33 0.33 N - 1 1 RS Ohms 0.28 0.31 TT s 1E-8 1E-9 EG eV 1.11 1.11 Page 5 www.protekdevices.com 05135 SLVU2.8 Only One Name Means ProTek'TionTM application information I/O LINE 1 3 GND 2 figure 1 - UNIDIRECTIONAL common mode PROTECTION Circuit connectivity is as follows: * Line 1 connected to Pin 3. * Pins 1 and 2 connected to ground. I/O LINE 1 2 D1 3 3 D2 1 2 GND GND figure 2 - BIDIRECTIONAL COMMON MODE PROTECTION Two SLUV2.8 devices used in parallel. Circuit connectivity is as follows: * Line 1 connected to Pin 1 of Device 1 and Pin 2 connected to Device 2. * Pin 2 of Device 1 and Pin 1 of Device 2 connected to ground. * Pin 3 of both Devices not connected. I/O LINE 1 1 2 D1 3 3 D2 1 2 I/O LINE 2 figure 3 - BIDIRECTIONAL DIFFERENTIAL MODE PROTECTION Two SLUV2.8 devices used in parallel. Circuit connectivity is as follows: * Line 1 connected to Pin 1 of Device 1 and Pin 2 connected to Device 2. * Line 2 connected to Pin 2 of Device 1 and Pin 1 of Device 2. * Pin 3 not connected. circuit board recommendations Circuit board layout is critical for electromagnetic compatibility protection. The following guidelines are recommended: * The protection device should be placed near the input terminals or connectors, the device will divert the transient current immediately before it can be coupled into the nearby traces. * The path length between the TVS device and the protected line should be minimized. * All conductive loops including power and ground loops should be minimized. * The transient current return path to ground should be kept as short as possible to reduce parasitic inductance. * Ground planes should be used whenever possible. For multilayer PCBs, use ground vias. 05135.R11 10/12 Page 6 www.protekdevices.com 05135 SLVU2.8 Only One Name Means ProTek'TionTM sot-23 package information outline dimensions dim millimeters A L inches min max min max A 2.80 3.04 0.110 0.120 B 1.20 1.40 0.047 0.055 C 0.89 1.11 0.035 0.044 D 0.37 0.50 0.015 0.020 G 1.78 2.04 0.070 0.081 H 0.013 0.100 0.001 0.004 J 0.085 0.177 0.003 0.007 K 0.45 0.60 0.018 0.024 L 0.89 1.02 0.035 0.040 S 2.10 2.50 0.083 0.098 V 0.45 0.60 0.018 0.024 3 B 1 0-10 S 2 K V J G C D H NOTES 1. 2. 3. 4. Controlling dimension: inches. Dimensioning and tolerances per ANSI Y14.5M, 1985. Pin 3 is the cathode (Unidirectional Only) Dimensions are exclusive of mold flash and metal burrs. A pad layout dimensions dim millimeters inches min max min max A 0.71 0.97 0.028 0.038 B 1.88 2.13 0.074 0.084 C 0.71 0.97 0.028 0.038 D 0.81 1.07 0.032 0.042 B NOTES D 1. Controlling dimension: inches. 05135.R11 10/12 C Page 7 www.protekdevices.com 05135 SLVU2.8 Only One Name Means ProTek'TionTM TAPE AND REEL P0 t 10 Pitches Cumulative Tolerance on Tape. 0.2 P2 D E Top Cover Tape Pin 1 A0 F W K0 B0 P User Direction of Feed specifications Reel Dia. Tape Width 178mm (7") 8mm A0 B0 K0 D E F W P0 P2 P tmax 3.15 0.10 2.77 0.10 1.30 0.10 1.55 0.10 1.75 0.10 3.50 0.05 8.00 0.30 4.00 0.10 2.00 0.05 4.00 0.10 0.228 Notes 1. 2. 3. 4. 5. Dimensions are in millimeters. Surface mount product is taped and reeled in accordance with EIA-481. Suffix - T7 = 7" Reel - 3,000 pieces per 8mm tape. Suffix - T13 = 13" Reel - 10,000 pieces per 8mm tape. Marking on Part - marking code (see page 2) and date code. Package outline, pad layout and tape specifications per document number 06012.R2 8/10. ORDERING INFORMATION base PART NUMBER LEADFREE SUFFIX TAPE SUFFIX QTY/REEL REEL SIZE TUBE qty SLVU2.8 -LF -T7 3,000 7" n/a SLVU2.8 -LF -T13 10,000 13" n/a This device is only available in a Lead-Free configuration. 05135.R11 10/12 Page 8 www.protekdevices.com 05135 SLVU2.8 Only One Name Means ProTek'TionTM company information COMPANY PROFILE In business more than 20 years, ProTek DevicesTM is a privately-held company located in Tempe, Arizona, that offers a product line of transient voltage suppressors (TVS); avalanche breakdown diodes; steering diode TVS arrays and other surge suppressor component products. These TVS devices protect electronic systems from the effects of lightning, electrostatic discharge (ESD), nuclear electromagnetic pulses (NEMP), inductive switching and EMI / RFI. ProTek Devices also offers high performance interface and linear products that include analog switches; multiplexers; LED drivers; audio control ICs; RF and related high frequency products. The analog devices work in a host of consumer; industrial; automotive and other applications. CONTACT US Corporate Headquarters 2929 South Fair Lane Tempe, Arizona 85282 USA By Telephone General: 602-431-8101 Sales: & Marketing: 602-414-5109 Customer Service: 602-414-5114 Product Technical Support: 602-414-5107 By Fax General: 602-431-2288 By E-mail: Sales: sales@protekdevices.com Customer Service: service@protekdevices.com Technical Support: support@protekdevices.com ProTek Devices (Asia Pacific) Pte. Ltd. 8 Ubi Road 2, #06-19 Zervex Singapore - 408538 Tel: +65-67488312 Fax: +65-67488313 Web www.protekdevices.com COPYRIGHT (c) ProTek Devices 2001 - This literature is subject to all applicable copyright laws and is not for resale in any manner. SPECIFICATIONS: ProTek reserves the right to change the electrical and or mechanical characteristics described herein without notice. DESIGN CHANGES: ProTek reserves the right to discontinue product lines without notice and that the final judgement concerning selection and specifications is the buyer's and that in furnishing engineering and technical assistance. ProTek assumes no responsibility with respect to the selection or specifications of such products. ProTek makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ProTek assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability without limitation special, consequential or incidental damages. LIFE SUPPORT POLICY: ProTek Devices products are not authorized for use in life support systems without written consent from the factory. 05135.R11 10/12 Page 9 www.protekdevices.com