GP2A200LCS0F Series
1
Sheet No.: D3-A05101EN
Date Jun. 30. 2005
© SHARP Corporation
Notice The content of data sheet is subject to change without prior notice.
In the absence of confi rmation by device specifi cation sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP
devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specifi cation sheets before using any SHARP device.
GP2A200LCS0F
Series
Detecting Distance : 2 to 22mm
*
OPIC Output,
Refl ective Photointerrupter with
Connector
■Description
GP2A200LCS0F Series are OPIC output, reflective
photointerrupters with emitter and detector facing the
same direction in a molding that provides non-contact
sensing. This family of devices uses light modulation to
reduce the affects of disturbing light, and the sensor is
optimized to work in the selected focal distance. A 3-pin
connector is included to allow remote-mount or off-board
designs.
■Features
1. Refl ective with OPIC Light Modulated Output
2. Highlights :
• Includes additional screw fi xing holes
• Position pin to prevent mis-alignment
• Long focal distance
3. Key Parameters :
• Detecting distance : 2 to 22mm (White paper)
5 to 15mm (Black paper)
• Undetecting distance : over 90mm (White paper)
• Connector :
GP2A200LCS0F
; Tyco Electronics AMP K.K.
(PN : 292133-3)
GP2A200LCSCF
; Tyco Electronics AMP K.K.
(PN : 292133-3)
GP2A240LCS0F
; Tyco Electronics AMP K.K.
(PN : 292133-3)
GP2A210LCSJF
; Tyco Electronics AMP K.K
.
(PN : 4-292133-3)
4. Lead free and RoHS directive compliant
■Agency approvals/Compliance
1. Compliant with RoHS directive
■Applications
1. General purpose detection of paper presence or mo-
tion.
2. Example: PPC, FAX, Printer
* "OPIC"(Optical IC) is a trademark of the SHARP Corporation. An OPIC consists of a light-detecting element and a signal-
processing
2
Sheet No.: D3-A05101EN
GP2A200LCS0F Series
■Internal Connection Diagram
■Outline Dimensions (Unit : mm)
Product mass : approx. 1.95g
Voltage regulator
Amp.
Comparator Oscillator circuit Sync. detecting circuit
Demodulator circuit
Reflective object
1
2
3
VCC
VOUT
GND
1
2
3
33
17.7
6
6.2
7.8
12
26.5
φ3+0
−0.2
3.1
(6.8)
9
4.5
8
4.5
2.5
(7.8)
(5.8)(0.65)(0.9)
2
φ3.2
1 2 3
1
2
3
VCC
VOUT
GND
Optical center
Connector : 292133-3 (Tyco Electronics AMP. K. K)
0 7
Date code
GP2A200LCS0F GP2A200LCSCF
GP2A210LCSJF
Product mass : approx. 1.95g Product mass : approx. 2.3g
Product mass : approx. 1.95g
GP2A240LCS0F
02
6
5.2
5.2
10.2 2
φ3.2
3.5
3.5
4.5
2
7
(5.8)
6.1
9.6
9
12
7.8
(7.8)
(6.8)
26.5
32
φ3+0.0
−0.2
Connector : 292133-3
(Tyco Electronics AMP K.K.)
3
2
1
Optical center
3.5
4-SR1
Date code
1
2
3
VCC
VOUT
GND
View A
View A
99
33 (6.8)
(7.8)
(5 .8)
17.7
66.2
φ3.2
4.54.5
2.5
2
98
12
7.8
26.5
3.1
φ3+0.0
−0.2
Connector : 4-292133-3 (Yellow)
(Tyco Electronics AMP K.K.)
123
Date code
1
2
3
VCC
VOUT
GND
Optical center
51
33 (6.8)
(7.8)
(5 .8)(0.65)
17.7
66.2
φ3.2
4.54.5
2.5
2
98
12
7.8
26.5
3.1
φ3+0.0
−0.2
Connector : 292133-3
(Tyco Electronics AMP K.K.)
1 2 3
Date code
1
2
3
VCC
VOUT
GND
Optical center
Connector terminal plating material : Sn
• Unspecifi ed tolerance
shall be as follows ;
Dimensions
Tolerance
less than 6
±0.2
6 or more
less than 14
±0.3
14 or more
±0.4
• *( ) : Reference dimensions
• Unspecifi ed tolerance
shall be as follows ;
Dimensions
Tolerance
less than 6
±0.2
6 or more
less than 14
±0.3
14 or more
±0.4
• *( ) : Reference dimensions
• Unspecifi ed tolerance
shall be as follows ;
Dimensions
Tolerance
less than 6
±0.2
6 or more
less than 14
±0.3
14 or more
±0.4
• *( ) : Reference dimensions
• Unspecifi ed tolerance
shall be as follows ;
Dimensions
Tolerance
less than 6
±0.2
6 or more
less than 14
±0.3
14 or more
±0.4
• *( ) : Reference dimensions
• : Portion Built-in IR-90 fi lter
3
Sheet No.: D3-A05101EN
GP2A200LCS0F Series
repeats in a 10 year cycle
Date code (2 digit)
1st digit 2nd digit
Year of production Month of production
A.D. Mark Month Mark
2000 0 1 1
2001 1 2 2
2002 2 3 3
2003 3 4 4
2004 4 5 5
2005 5 6 6
2006 6 7 7
2007 7 8 8
2008 8 9 9
2009 9 10 X
2010 0 11 Y
: : 12 Z
Country of origin
Japan
4
Sheet No.: D3-A05101EN
GP2A200LCS0F Series
■Absolute Maximum Ratings
■Electro-optical Characteristics
(Ta=25˚C)
Parameter Symbol Rating Unit
Supply voltage VCC −0.5 to +7V
Output voltage VO30 V
*1 Output current IOL 50 mA
*2 Operating temperature Topr −10 to +70 ˚C
*2 Storage temperature Tstg −20 to +80 ˚C
∗1 Sink current refer to
Fig.5.
∗2 The connector should be plugged in/out at normal temperature.
(Ta=25˚C)
Parameter Symbol Condhitions MIN. TYP. MAX. Unit
Supply voltage VCC −4.75 −5.25 V
Current dissipation (I) ICC Smoothing value VCC=5V, RL=∞−−
30 mA
*3 Current dissipation (II) ICCP Pulse peak value VCC=5V −−
150 mA
Low level output voltage VOL VCC=5V, IOL=16mA, at detecting time −−
0.4 V
High level output voltage VOH VCC=5V, RL=1kΩ, at non detecting time 4.5 −−V
*4 Non detection distance LLHL KODAK Gray Cards, VCC=5V −−
90 mm
GP2A210LCSJF
−−
70
*4 Detection distance
LHLS
KODAK Gray Cards, VCC=5V −−2mm
Black paper, VCC=5V −−5
LHLL
KODAK Gray Cards , VCC=5V 22 −−
mm
Black paper, VCC=5V 15 −−
*5 Response time tPLH VCC=5V −−1ms
tPHL −−1ms
*6 Acceptable illuminance Ev1 −3 000 −−lx
Ev2 1 500 −−lx
∗3 Refer to Fig.1.
∗4 Refer to Fig.2.
∗5 Refer to Fig.3.
*6 Refer to Fig.4.
Refl ective object Black paper (black) : Standard refl ective object (provided by SHARP Corporation)
KODAK Gray Cards (use the white side refl ects about 90%)
: Standard refl ective object (provided by SHARP Corporation)
PPC paper : Standard refl ective object (provided by SHARP Corporation)
5
Sheet No.: D3-A05101EN
GP2A200LCS0F Series
Fig.2 Test Condition for Detecting Distance Characteristics
VOH
VOL
LLHS
LHLS LHLL
LLHL
Output VO
Detecting distance L
Detection surface
Reflective object
Fig.1 Test Condition for Peak Pulse Value ICCP
VO
GND
Vr
tW
tP
V
ICCP=Vr/1Ω
tW (TYP.)=8μs (GP2A240LCS0F : 2.5 to 9.3μs)
tP (TYP.)=130μs (GP2A240LCS0F : 40 to 150μs)
VCC=5V
RL=1kΩ
R=1Ω
1
2
3
Photointerrupter
Fig.3 Test Circuit for Response Time
VO
GND VOH
1.5V
VOL
L
RL=1kΩ
VOUT
waveform
VCC=5V
Reflective object
Detection surface
With reflective object
Without reflective object
tPHL tPLH
1
2
3
Photointerrupter
EV1 : At non-detecting EV2 : At detecting
Illuminance shall be that on the emission/detection surface.
Output shall not go from "H" to "L".
Illuminance shall be that on the reflective
object.
Output shall not go from "L" to "H".
Light source A
Emission/detection surface
PPC paper
15mm
Emission/detection
surface
Light source A
Photointerrupter
Photointerrupter
Fig.4 Test Condition for External Disturbing Light Illuminance
6
Sheet No.: D3-A05101EN
GP2A200LCS0F Series
Fig.5 Output Current vs.
Ambient Temperature
Fig.6 Low Level Output Voltage vs.
Ambient Temperature
Fig.7 Low Level Output Voltage vs.
Low Level Output Current
Fig.8
Dissipation Current(Smoothing Value)
vs. Ambient Temperature
0
10
20
30
40
50
−100 25507570 100
Ambient temperature Ta (C)
Output Current IOL (mA)
V
CC
=5V
At detecting
Low level output voltage VOL (V)
Ambient temperature T
a
(C)
0
0.3
0.2
0.1
−100 10203040506070
I
OL=30mA
16mA
5mA
Low level output current I
OL (mA)
Low level output voltage VOL (V)
1 10 100
0.01
0.1
VCC=5V
At detecting
Dissipation current ICC (mA)
0
7
6
5
4
3
2
1
4.75 4.85 4.95 5.05 5.15 5.25
Supply voltage VCC (V)
Ta=−10˚C
25˚C
70˚C
Remarks : Please be aware that all data in the graph are just for reference and not for guarantee.
7
Sheet No.: D3-A05101EN
GP2A200LCS0F Series
■Design Considerations
●Design guide
1) VO terminal : Open collector output
This product operates the light emitter by pulse drive. Please supply the stable supply voltage in order to
prevent error operation by pulse current.
Please use this device after connecting a capacitor between VO and GND for prevention of line noise.
2) Prevention of detection error
Please be careful that you need to keep the direct inverter light away from the photo detecting surface
since the device will not operate correctly in such case.
In addition, we recommend to make sure the operation test in the actual application.
3) Plugging in/out
The connector should be plugged in/out at normal temperature.
This product is not designed against irradiation and incorporates non-coherent IRED.
●Parts
This product is assembled using the below parts.
• Photodetector (Q'ty : 1)
[Using a silicon photodiode as light detecting portion, and a bipolar IC as signal processing circuit]
Category Maximum Sensitivity
wavelength (nm)
Sensitivity
wavelength (nm) Response time (μs)
Phototransistor 900 700 to 1 200 400
• Photo emitter (Q'ty : 1)
Category Material Maximum light emitting
wavelength (nm) I/O Frequency (MHz)
Infrared emitting diode
(non-coherent) Gallium arsenide (GaAs) 950 0.3
• Material
Case Lens Bottom cover
GP2A200LCS0F
Black polyphernylene
Sulfi de resin (UL94 V-0)
Polycarbonate resin
(UL94 V-2)
Polycarbonate resin (Gray)
(UL94 V-2)
GP2A200LCSCF
GP2A210LCSJF∗
GP2A240LCS0F Polycarbonate resin (Navy Blue)
(UL94 V-2)
∗The IR-90 fi lter (Fuji Photo Film Co., Ltd.) is inserted between case and detector side lens.
• Others
Laser generator is not used.
8
Sheet No.: D3-A05101EN
GP2A200LCS0F Series
■Manufacturing Guidelines
●Cleaning instructions
Polycarbonate resin is used as the material of the lens surface. So this product shall not be cleaned by
cleaning solvent absolutely. Dust and stain shall clean by air blow, or shall clean by soft cloth.
●Presence of ODC
This product shall not contain the following materials.
And they are not used in the production process for this product.
Regulation substances : CFCs, Halon, Carbon tetrachloride, 1.1.1-Trichloroethane (Methylchloroform)
Specifi c brominated fl ame retardants such as the PBBOs and PBBs are not used in this product at all.
This product shall not contain the following materials banned in the RoHS Directive (2002/95/EC).
•Lead, Mercury, Cadmium, Hexavalent chromium, Polybrominated biphenyls (PBB), Polybrominated
diphenyl ethers (PBDE).
9
Sheet No.: D3-A05101EN
GP2A200LCS0F Series
■Package specifi cation
●Case package
Package materials
Anti-static plastic bag : Polyethtylene
Moltopren : Urethane
Packing case : Corrugated fi berboard
Package method
100 pcs of products shall be packaged in a plastic bag, Ends shall be sealed by stapler. The bottom ot the
packing case is covered with moltopren, and 2 plastic bags shall be put int the packing case.
Moltopren should be located after all product are settled (1 packing conteains 200 pcs).
Packing composition
Moltopren
plastic bag
Packing case
10
Sheet No.: D3-A05101EN
GP2A200LCS0F Series
■Important Notices
· The circuit application examples in this publication
are provided to explain representative applications of
SHARP devices and are not intended to guarantee any
circuit design or license any intellectual property rights.
SHARP takes no responsibility for any problems related
to any intellectual property right of a third party resulting
from the use of SHARP's devices.
· Contact SHARP in order to obtain the latest device
specification sheets before using any SHARP device.
SHARP reserves the right to make changes in the
specifi cations, characteristics, data, materials, structure,
and other contents described herein at any time
without notice in order to improve design or reliability.
Manufacturing locations are also subject to change
without notice.
· Observe the following points when using any devices
in this publication. SHARP takes no responsibility for
damage caused by improper use of the devices which
does not meet the conditions and absolute maximum
ratings to be used specifi ed in the relevant specifi cation
sheet nor meet the following conditions:
(i) The devices in this publication are designed for use
in general electronic equipment designs such as:
--- Personal computers
--- Offi ce automation equipment
--- Telecommunication equipment [terminal]
--- Test and measurement equipment
--- Industrial control
--- Audio visual equipment
--- Consumer electronics
(ii) Measures such as fail-safe function and redundant
design should be taken to ensure reliability and safety
when SHARP devices are used for or in connection
with equipment that requires higher reliability such as:
--- Transportation control and safety equipment (i.e.,
aircraft, trains, automobiles, etc.)
--- Traffi c signals
--- Gas leakage sensor breakers
--- Alarm equipment
--- Various safety devices, etc.
(iii) SHARP devices shall not be used for or in
connection with equipment that requires an extremely
high level of reliability and safety such as:
--- Space applications
--- Telecommunication equipment [trunk lines]
--- Nuclear power control equipment
--- Medical and other life support equipment (e.g.,
scuba).
· If the SHARP devices listed in this publication fall
within the scope of strategic products described in the
Foreign Exchange and Foreign Trade Law of Japan, it
is necessary to obtain approval to export such SHARP
devices.
· This publication is the proprietary product of SHARP
and is copyrighted, with all rights reserved. Under
the copyright laws, no part of this publication may be
reproduced or transmitted in any form or by any means,
electronic or mechanical, for any purpose, in whole or in
part, without the express written permission of SHARP.
Express written permission is also required before any
use of this publication may be made by a third party.
· Contact and consult with a SHARP representative
if there are any questions about the contents of this
publication.
[H176]
