MCP2035 Analog Front-End Device for BodyCom Applications Device Features: Description: * * * * The MCP2035 is a single-channel, stand-alone Analog Front-End (AFE) device for low-frequency (LF) signal detection and low-power short range transponder applications, such as BodyCom communications. * * * * * * * * * * Single Analog Input Pin for Signal Detection High Input Detection Sensitivity (3 mVPP, typical) High Modulation Depth Sensitivity (as low as 8%) Three Output Type Selections: - Demodulated Data - Carrier Clock - Received Signal Strength Indicator (RSSI) Input Carrier Frequency: 125 kHz, typical Input Data Rate: 10 Kbps, maximum 8 Internal Configuration Registers Bidirectional Transponder Communication via the same input pin (LF talk-back) Programmable Antenna Tuning Capacitance (up to 63 pF, 1 pF/step) Programmable Output Enable Filter Low Standby Current: 2 A, typical Low Operating Current: 10 A, typical Serial Peripheral Interface (SPI) with external devices Industrial and Extended Temperature Range: -40C to +85C (Industrial) Typical Applications: * BodyCom Applications * Security Industry Applications * Automotive Industry Applications The device can detect an input signal with amplitude as low as ~1 mVPP, and can demodulate an amplitudemodulated input signal with as low as 8% modulation depth. The device can also transmit data (LF talk-back) by clamping and unclamping the input LC antenna voltage. The device can output demodulated data, carrier clock or RSSI current, depending on the output-type selection configuration register bit settings. The demodulated data and carrier clock outputs are available on the LFDATA pin, while the RSSI output is available on the RSSI pin. The RSSI current output is linearly proportional to the input signal strength. The device has programmable internal tuning capacitors for the input channel. The user can program the input tuning capacitors up to 63 pF, 1 pF per step. The internal tuning capacitors can be used effectively for fine-tuning of the external LC resonant circuit. The device has eight volatile internal configuration registers for dynamic configurations of the device operation on-the-fly. All registers are readable and programmable using the serial SPI commands, except the read-only STATUS register. The device is optimized for very low current consumption and has various battery-saving lowpower modes (Sleep, Standby, Active). This device is available in a 14-pin TSSOP package. Package Type: MCP2035 TSSOP VSS 1 14 VSS LCCOM CS 2 13 SCLK/ALERT 3 RSSI 4 12 NC LCX 11 LFDATA/ CCLK/SDIO VDD 2012 Microchip Technology Inc. NC 5 6 7 10 NC 9 NC 8 VDD DS22304A-page 1 MCP2035 NOTES: DS22304A-page 2 2012 Microchip Technology Inc. MCP2035 1.0 ELECTRICAL SPECIFICATIONS Absolute Maximum Ratings() Ambient temperature under bias.............................................................................................................-40C to +125C Storage temperature .............................................................................................................................. -65C to +150C Voltage on VDD with respect to VSS .......................................................................................................... -0.3V to +6.5V Voltage on all other pins with respect to VSS ................................................................................. -0.3V to (VDD + 0.3V) Maximum current out of VSS pin ...........................................................................................................................300 mA Maximum current into VDD pin ..............................................................................................................................250 mA Maximum LC Input Voltage (LCX) loaded, with device ....................................................................................... 10.0 VPP Maximum LC Input Voltage (LCX) unloaded, without device ............................................................................ 700.0 VPP Maximum Input Current (rms) into device (LCX Input Channel) .............................................................................10 mA Human Body ESD rating ......................................................................................................................2000 (minimum) V Machine Model ESD rating ....................................................................................................................200 (minimum) V Notice: Stresses above those listed under "Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. DC CHARACTERISTICS Electrical Specifications: Standard Operating Conditions (unless otherwise stated), Operating temperature: -40C TA +85C, LCX Input Signal: Sinusoidal 300 mVPP, Carrier Frequency = 125 kHz, LCCOM connected to VSS, Bits <3:1> of Configuration Register 0: LCXEN = 0, LCZEN = LCYEN = 1. Sym. Min. Typ.(2) Max. Units Supply Voltage VDD 2.0 3.0 3.6 V VDD Start Voltage to ensure internal Power-on Reset signal VPOR -- -- 1.8 V Modulation Transistor-on Resistance RM -- 50 100 VDD = 3.0V Active Current (detecting signal) 1 LC Input Channel (LCX) is Receiving Signal IACT -- 10 -- A CS = VDD Input = Continuous Wave (CW) Amplitude = 300 mVPP LCX input channel is enabled. Standby Current (wait to detect signal) ISTDBY -- 2 5 A CS = VDD; ALERT = VDD LCX input channel is enabled. Sleep Current ISLEEP -- 0.2 1 A CS = VDD; ALERT = VDD Analog Input Leakage Current on LCX and LCCOM pins IAIL -- -- 1 A VDD = 3.6V, VSS VIN 1V with respect to ground. Internal tuning capacitors are switched off, tested in Sleep mode Digital Input Low Voltage VIL VSS -- 0.3 VDD V SCLK, SDI, CS Digital Input High Voltage VIH 0.8 VDD -- VDD V SCLK, SDI, CS Parameters Note 1: 2: 3: Conditions These parameters are characterized but not tested. Data in "Typ." column is at 3.0V, +25C unless otherwise stated. These parameters are for design guidance only and are not tested. Negative current is defined as current sourced by the pin. 2012 Microchip Technology Inc. DS22304A-page 3 MCP2035 DC CHARACTERISTICS (CONTINUED) Electrical Specifications: Standard Operating Conditions (unless otherwise stated), Operating temperature: -40C TA +85C, LCX Input Signal: Sinusoidal 300 mVPP, Carrier Frequency = 125 kHz, LCCOM connected to VSS, Bits <3:1> of Configuration Register 0: LCXEN = 0, LCZEN = LCYEN = 1. Sym. Min. Typ.(2) Max. Units IIL -- -- 1 A VDD = 3.6V VSS VPIN VDD VPIN VDD Digital Output Low Voltage ALERT, LFDATA/SDIO VOL -- -- VSS +0.4 V Analog Front-End section IOL = 1.0 mA, VDD = 2.0V Digital Output High Voltage ALERT, LFDATA/SDIO VOH VDD - 0.5 -- -- V IOH = -400 A, VDD = 2.0V Digital Input Pull-Up Resistor CS, SCLK RPU 50 200 350 k VDD = 3.6V Parameters Digital Input Leakage Current SDI, SCLK, CS (Note 3) Note 1: 2: 3: Conditions These parameters are characterized but not tested. Data in "Typ." column is at 3.0V, +25C unless otherwise stated. These parameters are for design guidance only and are not tested. Negative current is defined as current sourced by the pin. DS22304A-page 4 2012 Microchip Technology Inc. 2012 Microchip Technology Inc. AC CHARACTERISTICS Electrical Specifications: Standard Operating Conditions (unless otherwise stated), Supply Voltage: 2.0V VDD 3.6V, Operating temperature: -40C TA +85C, LCCOM connected to VSS, LCX Input Signal: Sinusoidal 300 mVPP, Carrier Frequency = 125 kHz, Bits <3:1> of Configuration Register 0: LCXEN = 0, LCZEN = LCYEN = 1. Sym. Min. Typ(2) Max. Units Input Sensitivity VSENSE 1 3.0 6 mVPP Coil de-Q'ing Voltage - RF Limiter (RFLM) must be active VDE_Q 3 -- 5 V VDD = 3.0V, Force IIN = 5 A (worst case) RF Limiter Turn-on Resistance at LCX pin RFLM -- 300 700 VDD = 2.0V, VIN = 8 VDC Sensitivity Reduction SADJ -- 0 -- dB -- -30 -- dB VDD = 3.0V No sensitivity reduction selected Maximum reduction selected Monotonic increment in attenuation value from setting = 0000 to 1111 by design -- 60 84 % 33% setting -- 33 49 % 14% setting -- 14 26 % Parameters Conditions VDD = 3.0V Output enable filter disabled AGCSIG = 0; MODMIN = 00 (33% modulation depth setting) Input = Continuous Wave (CW) Output = Logic level transition from low-to-high at sensitivity level for CW input. Minimum Modulation Depth 60% setting VIN_MOD 8% 8 Carrier frequency Input modulation frequency FCARRIER -- 125 -- kHz FMOD -- -- 10 kHz Input data rate with NRZ data format. VDD = 3.0V Minimum modulation depth setting = 33% Input conditions: Amplitude = 300 mVPP Modulation depth = 100% Parameter is characterized but not tested. Data in "Typ." column is at 3.0V, +25C unless otherwise stated. These parameters are for design guidance only and are not tested. Required output enable filter high time must account for input path analog delays (= TOEH - TDR + TDF). Required output enable filter low time must account for input path analog delays (= TOEL + TDR - TDF). MCP2035 DS22304A-page 5 Note 1: 2: 3: 4: % VDD = 3.0V See Section 5.20 "Minimum Modulation Depth Requirement for Input Signal". See Modulation Depth Definition in Figure 5-5. Electrical Specifications: Standard Operating Conditions (unless otherwise stated), Supply Voltage: 2.0V VDD 3.6V, Operating temperature: -40C TA +85C, LCCOM connected to VSS, LCX Input Signal: Sinusoidal 300 mVPP, Carrier Frequency = 125 kHz, Bits <3:1> of Configuration Register 0: LCXEN = 0, LCZEN = LCYEN = 1. Parameters LCX Tuning Capacitor Sym. Min. Typ(2) Max. Units CTUNX -- 0 -- pF VDD = 3.0V, Config. Reg. 1, bits <6:1> Setting = 000000 44 59 82 pF 63 pF 30% Config. Reg. 1, bits <6:1> Setting = 111111 63 steps, approx. 1 pF/step Monotonic increment in capacitor value from setting = 000000 to 111111 by design Conditions 2012 Microchip Technology Inc. Q of Internal Input Tuning Capacitors Q_C 50(1) -- -- Demodulator Charge Time (delay time of demodulated output to rise) TDR -- 50 -- s VDD = 3.0V Minimum modulation depth setting = 33% Input conditions: Amplitude = 300 mVPP Modulation depth = 100% Demodulator Discharge Time (delay time of demodulated output to fall) TDF -- 50 -- s VDD = 3.0V MOD depth setting = 33% Input conditions: Amplitude = 300 mVPP Modulation depth = 100% Rise time of LFDATA TRLFDATA -- 0.5 -- s VDD 3.0V. Time is measured from 10% to 90% of amplitude Fall time of LFDATA TFLFDATA -- 0.5 -- s VDD 3.0V Time is measured from 10% to 90% of amplitude TSTAB 4 -- -- ms AGC initialization time TAGC -- 3.5 -- ms High time after AGC initialization time TPAGC -- 62.5 -- s Automatic Gain Control (AGC) stabilization time (TAGC + TPAGC) Note 1: 2: 3: 4: Parameter is characterized but not tested. Data in "Typ." column is at 3.0V, +25C unless otherwise stated. These parameters are for design guidance only and are not tested. Required output enable filter high time must account for input path analog delays (= TOEH - TDR + TDF). Required output enable filter low time must account for input path analog delays (= TOEL + TDR - TDF). MCP2035 DS22304A-page 6 AC CHARACTERISTICS (CONTINUED) 2012 Microchip Technology Inc. AC CHARACTERISTICS (CONTINUED) Electrical Specifications: Standard Operating Conditions (unless otherwise stated), Supply Voltage: 2.0V VDD 3.6V, Operating temperature: -40C TA +85C, LCCOM connected to VSS, LCX Input Signal: Sinusoidal 300 mVPP, Carrier Frequency = 125 kHz, Bits <3:1> of Configuration Register 0: LCXEN = 0, LCZEN = LCYEN = 1. Parameters Gap time after AGC stabilization time Time element of pulse Sym. Min. Typ(2) Max. Units TGAP 200 -- -- s TE 100 -- -- s ms Conditions Minimum pulse width Time from exiting Sleep or POR to being ready to receive signal TRDY -- -- 50(1) Minimum time AGC level must be held after receiving AGC Preserve command TPRES 5(1) -- -- ms AGC level must not change more than 10% during TPRES Internal RC oscillator frequency FOSC 27 32 35.5 kHz Internal clock trimmed at 32 kHz during test Inactivity Timer time-out TINACT 13.5 16 17.75 ms 512 cycles of RC oscillator @ FOSC Alarm Timer time-out TALARM 27 32 35.5 ms 1024 cycles of RC oscillator @ FOSC RIN -- 800(1) -- k LCCOM grounded, VDD = 3V, FCARRIER = 125 kHz CIN -- 24(1) -- pF LCCOM grounded, VDD = 3V, FCARRIER = 125 kHz TOEH Input Resistance (LCX) Input Parasitic Capacitance (LCX) Minimum output enable filter high time OEH (Bits Config0<8:7>) 01 = 1 ms 32 (~1 ms) -- -- 10 = 2 ms 64 (~2 ms) -- -- 11 = 4 ms 128 (~4 ms) -- -- -- -- -- 00 = Filter Disabled clock count RC oscillator = FOSC (see FOSC specification for variations). Viewed from the pin input: (Note 3) Minimum output enable filter low time OEL (Bits Config0<6:5>) 00 = 1 ms -- -- 32 (~1 ms) -- -- 10 = 2 ms 64 (~2 ms) -- -- 128 (~4 ms) -- -- 11 = 4 ms DS22304A-page 7 Note 1: 2: 3: 4: TOEL clock count RC oscillator = FOSC Viewed from the pin input: (Note 4) Parameter is characterized but not tested. Data in "Typ." column is at 3.0V, +25C unless otherwise stated. These parameters are for design guidance only and are not tested. Required output enable filter high time must account for input path analog delays (= TOEH - TDR + TDF). Required output enable filter low time must account for input path analog delays (= TOEL + TDR - TDF). MCP2035 32 (~1 ms) 01 = 1 ms Electrical Specifications: Standard Operating Conditions (unless otherwise stated), Supply Voltage: 2.0V VDD 3.6V, Operating temperature: -40C TA +85C, LCCOM connected to VSS, LCX Input Signal: Sinusoidal 300 mVPP, Carrier Frequency = 125 kHz, Bits <3:1> of Configuration Register 0: LCXEN = 0, LCZEN = LCYEN = 1. Parameters Sym. Min. Typ(2) Max. TOET -- -- 96 (~3 ms) Units Conditions Maximum output enable filter period OEH OEL TOEH TOEL 01 00 = 1 ms 1 ms (Filter 1) 01 01 = 1 ms 1 ms (Filter 1) -- -- 96 (~3 ms) 01 10 = 1 ms 2 ms (Filter 2) -- -- 128 (~4 ms) 01 11 = 1 ms 4 ms (Filter 3 -- -- 192 (~6 ms) 10 00 = 2 ms 1 ms (Filter 4) -- -- 128 (~4 ms) 10 01 = 2 ms 1 ms (Filter 4) -- -- 128 (~4 ms) 10 10 = 2 ms 2 ms (Filter 5) -- -- 160 (~5 ms) 10 11 = 2 ms 4 ms (Filter 6) -- -- 250 (~8 ms) 11 00 = 4 ms 1 ms (Filter 7) -- -- 192 (~6 ms) 11 01 = 4 ms 1 ms (Filter 7) -- -- 192 (~6 ms) 11 10 = 4 ms 2 ms (Filter 8) -- -- 256 (~8 ms) 11 11 = 4 ms 4 ms (Filter 9) -- -- 320 (~10 ms) 00 XX = Filter Disabled -- -- -- -- 0.65 2 A VIN = 37 mVPP RSSI current output 2012 Microchip Technology Inc. RSSI current linearity Note 1: 2: 3: 4: IRSSI ILRRSSI RC oscillator = FOSC clock count LFDATA output appears as long as input signal level is greater than VSENSE. 6 12 20.3 A VIN = 370 mVPP -- 100 -- A VDD = 3.0V, VIN = 0 to 4 VPP Linearly increases with input signal amplitude. Tested at VIN = 37 mVPP, 100 mVPP, and 370 mVPP at +25C. -15 -- 15 % Tested at room temperature only (see Equation 5-1 and Figure 5-7 for test method). Parameter is characterized but not tested. Data in "Typ." column is at 3.0V, +25C unless otherwise stated. These parameters are for design guidance only and are not tested. Required output enable filter high time must account for input path analog delays (= TOEH - TDR + TDF). Required output enable filter low time must account for input path analog delays (= TOEL + TDR - TDF). MCP2035 DS22304A-page 8 AC CHARACTERISTICS (CONTINUED) MCP2035 SPI TIMING Electrical Specifications: Standard Operating Conditions (unless otherwise stated), Supply Voltage: 2.0V VDD 3.6V, Operating temperature: -40C TA +85C, LCX Input Signal: Sinusoidal 300 mVPP, Carrier Frequency: 125 kHz, LCCOM connected to VSS Parameters Sym Min Typ(1) Max Units Conditions SCLK Frequency FSCLK -- -- 3 MHz CS fall to first SCLK edge setup time TCSSC 100 -- -- ns SDI setup time TSU 30 -- -- ns SDI hold time THD 50 -- -- ns SCLK high time THI 150 -- -- ns SCLK low time TLO 150 -- -- ns SDO setup time TDO -- -- 150 ns SCLK last edge to CS rise setup time TSCCS 100 -- -- ns CS high time TCSH 500 -- -- ns CS rise to SCLK edge setup time TCS1 50 -- -- ns SCLK edge to CS fall setup time TCS0 50 -- -- ns SCLK edge when CS is high Rise time of SPI data (SPI Read command) TRSPI -- 10 -- ns VDD 3.0V; time is measured from 10% to 90% of amplitude Fall time of SPI data (SPI Read command) TFSPI -- 10 -- ns VDD 3.0V; time is measured from 90% to 10% of amplitude Note 1: Data in "Typ." column is at 3.0V, +25C unless otherwise stated. These parameters are for design guidance only and are not tested. TEMPERATURE CHARACTERISTICS Electrical Specifications: Unless otherwise indicated, VDD = 2.0V to 3.6V, VSS = GND. Parameters Symbol Min Typical Max Units Specified Temperature Range TA -40 -- +85 C Operating Temperature Range TA -40 -- +125 C Storage Temperature Range TA -65 -- +150 C JA -- 100 -- C/W Conditions Temperature Ranges Thermal Package Resistances Thermal Resistance, 14L-TSSOP 2012 Microchip Technology Inc. DS22304A-page 9 MCP2035 NOTES: DS22304A-page 10 2012 Microchip Technology Inc. MCP2035 2.0 TYPICAL PERFORMANCE CURVES The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range. Note: Note: Unless otherwise indicated, VDD = 3V, Carrier Frequency = 125 kHz, LCCOM = connected to VSS, TA = +25C. 5 4 3 2 1 3V VDD (V) FIGURE 2-2: 27 0 3.6 V FIGURE 2-5: Oscillator Frequency Histograms vs. Temperature at VDD = 3V. De-Q'ed (Loaded) Coil Voltage (VPP) Oscillator Frequency (kHz) 35 34 33 Osc. Freq. @ VDD = 3.6V 32 31 Osc. Freq. @ VDD = 2.0V 29 -50 -25 0 25 50 75 100 125 12 10 8 6 4 2 0 0 Temperature (C) FIGURE 2-3: Oscillator Frequency vs. Temperature, VDD = 3.6V and 2.0V. 2012 Microchip Technology Inc. 35 Oscillator Frequency (kHz) Typical Active Current. 30 35 -40oC 6 34 7 -40C 25C 85C 33 Current Draw (A) 8 VDD = 3.6V 32 +85oC +25oC 50.0% 45.0% 40.0% 35.0% 30.0% 25.0% 20.0% 15.0% 10.0% 5.0% 0.0% 31 Active Current (LCX Channel Enabled) 9 FIGURE 2-4: Oscillator Frequency Histograms vs. Temperature, VDD = 2V. 30 Typical Standby Current. 2V 34 Oscillator Frequency (kHz) 29 FIGURE 2-1: 3.6 V 33 3V VDD (V) Percentage of Occurences (%) 2V 27 0 32 0.5 31 1 30 -40oC 1.5 -40C 25C 85C 29 +25oC 28 2 VDD = 2.0V 28 Current Draw (A) +85oC 50.0% 45.0% 40.0% 35.0% 30.0% 25.0% 20.0% 15.0% 10.0% 5.0% 0.0% Percentage of Occurences (%) Standby Current (LCX Channel Enabled) 2.5 200 400 600 Unloaded Coil Voltage (VPP) 800 FIGURE 2-6: De-Q'ed Voltage vs. Unloaded Coil Voltage. DS22304A-page 11 MCP2035 Note: Unless otherwise indicated, VDD = 3V, Carrier Frequency = 125 kHz, LCCOM = connected to VSS. 70 70 60 Capacitance (pF) 80 Ohms 60 50 40 30 50 40 30 20 20 10 10 0 0 0 2 4 VDD (V) 0 6 FIGURE 2-7: Modulation Transistor-on Resistance (+25C). 40 60 Bit Setting (Steps) 80 FIGURE 2-10: Typical Tuned Capacitance Value vs. Configuration Register Bit Setting (VDD = 3V, Temperature = +25C). 25 70 60 20 Capacitance (pF) Sensitivity (mVPP) 20 15 10 50 40 30 20 5 10 0 0 0 50 100 150 200 250 300 350 400 450 0 20 Frequency (kHz) FIGURE 2-8: Bandwidth. Input Channel Sensitivity vs. 80 FIGURE 2-11: Typical Tuned Capacitance Value vs. Configuration Register Bit Setting (VDD = 3V, Temperature = -40C). 120 70 +25 C +85 C 60 Capacitance (pF) 100 RSSI (A) 40 60 Bit Setting (steps) 80 -40 C 60 40 20 50 40 30 20 10 6 5 5.5 4 4.5 3 3.5 2 2.5 1 1.5 0 0.5 0 Input Voltage (V) FIGURE 2-9: Typical RSSI Output Current vs. Input Signal Strength. DS22304A-page 12 0 0 20 40 60 Bit Setting (Steps) 80 FIGURE 2-12: Typical Tuned Capacitance Value vs. Configuration Register Bit Setting (VDD = 3V, Temperature = +85C). 2012 Microchip Technology Inc. MCP2035 Note: Unless otherwise indicated, VDD = 3V, Carrier Frequency = 125 kHz, LCCOM = connected to VSS. RSSI Current (mA) 80 Device A Device B Device C Device D 70 60 50 40 30 20 10 0 0 Note: 2 4 Input Voltage (V) 6 Equal amplitude is applied to each device. TDR (s) FIGURE 2-13: Examples of RSSI Output Current Variations Between Device to Device at Room Temperature. 100 90 80 70 60 50 40 30 20 10 0 8% 14% 33% 60% 85C 25C -20C -40C Temperature (C) FIGURE 2-14: Example of Typical TDR Changes over Temperature. Input Signal Condition: Amplitude = 300 mVPP, Modulation Depth = 100 %. 60 TDF (s) 50 40 60% 30 20 33% 14% 10 8% 0 85C 25C -20C Temperature (C) -40C FIGURE 2-15: Example of Typical TDF Changes over Temperature. Input Signal Condition: Amplitude = 300 mVPP, Modulation Depth = 100 %. 2012 Microchip Technology Inc. DS22304A-page 13 MCP2035 2.1 Performance Plots (a) Sensitivity = 1.06 mVPP Demodulated output Input signal (b) Sensitivity = 3 mVPP Demodulated output Input signal FIGURE 2-16: DS22304A-page 14 Input Sensitivity Example. 2012 Microchip Technology Inc. MCP2035 Note: Ch2 is the input and Ch1 is the output (demodulated data appears after AGC Initialization time (TAGC)). Output Enable Filter is disabled. FIGURE 2-17: Typical AGC Initialization Time at Room Temperature (VDD = 3V). 2012 Microchip Technology Inc. DS22304A-page 15 MCP2035 Note: Ch3 is the input with correct Output Enable Filter timing. Ch1 is the demodulated LFDATA output. Ch2 is the ALERT pin output. It shows that the ALERT output pin maintains logic high if the input signal meets the programmed filter timing requirement. FIGURE 2-18: DS22304A-page 16 ALERT Output Example: With No Parity Error and no 32 ms Alarm Timer Time-out. 2012 Microchip Technology Inc. MCP2035 Note: The 32 ms Alarm Timer is enabled only if the Output Enable Filter is enabled. Ch3 is the input signal with incorrect Output Enable Filter timing. Ch1 is the demodulated LFDATA output. No output since the input filter is not matched. Ch2 is the ALERT output. The output shows that the logic level changes after 32 ms from the AGC initialization time (TAGC) if the input signal does not meet the programmed filter timing requirement. FIGURE 2-19: ALERT Output Example: With 32 ms Alarm Timer Timed Out. 2012 Microchip Technology Inc. DS22304A-page 17 MCP2035 (a) Output (Ch1): Device repeats Soft Reset after 16 ms, Inactivity Timer has timed out (b) Input (Ch2): Input has no modulation Note: Ch2 is the input without modulation (i.e., noise). Ch1 is the output at the LFDATA pin due to the 16 ms Soft Inactivity Timer time out. Note the 3.5 ms AGC initialization time after the Soft Reset. The cases shown above apply when the Output Filter is disabled. FIGURE 2-20: Examples of Soft Inactivity Timer Time Out: This output is available only if the Output Enable Filter is disabled. DS22304A-page 18 2012 Microchip Technology Inc. MCP2035 Coil Voltage LCX Clock Pulses SCLK Clamp On Command SDI Coil Voltage LCX Clock Pulses SCLK Clamp Off Command FIGURE 2-21: SDI Examples of Clamp-On and Clamp-Off Commands and Changes in Coil Voltage. 2012 Microchip Technology Inc. DS22304A-page 19 MCP2035 Demodulated output Input signal with 77% modulation depth FIGURE 2-22: Example of Minimum Modulation Depth Setting: Modulation Depth of Input Signal = 77%, Minimum Modulation Depth (MODMIN) Setting = 60%. Demodulated output Input signal with 56% modulation depth Note: There is no demodulated output since the modulation depth of the input signal is lower than the minimum modulation depth setting. The device will have demodulated output if the Minimum Modulation Depth option is set to 8%, 14%, or 33%. FIGURE 2-23: Example of Minimum Modulation Depth Setting: Modulation Depth of Input Signal = 56%, Minimum Modulation Depth (MODMIN) Setting = 60%. DS22304A-page 20 2012 Microchip Technology Inc. MCP2035 Demodulated output Input signal with 42% modulation depth FIGURE 2-24: Example of Minimum Modulation Depth Setting: Modulation Depth of Input Signal = 42%, Minimum Modulation Depth (MODMIN) Setting = 33%. Demodulated output Input signal with 14% modulation depth FIGURE 2-25: Example of Minimum Modulation Depth Setting: Modulation Depth of Input Signal = 14%, Minimum Modulation Depth (MODMIN) Setting = 14%. 2012 Microchip Technology Inc. DS22304A-page 21 MCP2035 Filter 1 Output Enable Filter Timing of Input Signal TOEH = 1 ms TOEL = 1 ms TOET = 3 ms Configuration Bit Settings OEH OEL 01 00 01 01 or Filter 2 Output Enable Filter Timing of Input Signal TOEH = 1 ms TOEL = 2 ms TOET = 4 ms Configuration Bit Settings OEH OEL 01 10 Filter 3 Output Enable Filter Timing of Input Signal TOEH = 1 ms TOEL = 4 ms TOET = 6 ms FIGURE 2-26: Outputs. DS22304A-page 22 Configuration Bit Settings OEH OEL 01 11 Examples of Output Enable Filters 1 through 3 (Wake-up Filters) and Demodulated 2012 Microchip Technology Inc. MCP2035 Filter 4 Output Enable Filter Timing of Input Signal TOEH = 2 ms TOEL = 1 ms TOET = 4 ms Configuration Bit Settings OEH OEL 10 00 10 01 or Filter 5 Output Enable Filter Timing of Input Signal TOEH = 2 ms TOEL = 2 ms TOET = 5 ms Configuration Bit Settings OEH OEL 10 10 Filter 6 Output Enable Filter Timing of Input Signal TOEH = 2 ms TOEL = 4 ms TOET = 8 ms FIGURE 2-27: Outputs. Configuration Bit Settings OEH OEL 10 11 Examples of Output Enable Filters 4 through 6 (Wake-up Filters) and Demodulated 2012 Microchip Technology Inc. DS22304A-page 23 MCP2035 Filter 7 Output Enable Filter Timing of Input Signal TOEH = 4 ms TOEL = 1 ms TOET = 6 ms Configuration Bit Settings OEH OEL 11 00 11 01 or Filter 8 Output Enable Filter Timing of Input Signal TOEH = 4 ms TOEL = 2 ms TOET = 8 ms Configuration Bit Settings OEH OEL 11 10 Filter 9 Output Enable Filter Timing of Input Signal TOEH = 4 ms TOEL = 4 ms TOET = 10 ms FIGURE 2-28: Outputs. DS22304A-page 24 Configuration Bit Settings OEH OEL 11 11 Examples of Output Enable Filters 7 through 9 (Wake-up Filters) and Demodulated 2012 Microchip Technology Inc. MCP2035 LFDATA Output Input Signal Note: Demodulated output is available immediately after AGC initialization. FIGURE 2-29: Input Signal and Demodulated Output When the Output Enable Filter is Disabled. LFDATA Output Input Signal Note: Demodulated output is available only if the incoming signal meets the enable filter timing criteria that is defined in the Configuration Register 0 (Register 5-1). If the criteria is met, the output is available after the low timing (TOEL) of the Enable Filter. FIGURE 2-30: Input Signal and Demodulator Output When Output Enable Filter is Enabled and Input Meets Filter Timing Requirements. 2012 Microchip Technology Inc. DS22304A-page 25 MCP2035 No LFDATA Output Input Signal FIGURE 2-31: No Demodulator Output When Output Enable Filter is Enabled But Input Does Not Meet Filter Timing Requirements. DS22304A-page 26 2012 Microchip Technology Inc. MCP2035 Carrier Clock Output Carrier Input (a) Carrier Clock Output with Carrier/1 Option Carrier Clock Output Carrier Input (b) Carrier Clock Output with Carrier/4 Option FIGURE 2-32: Carrier Clock Output Examples. 2012 Microchip Technology Inc. DS22304A-page 27 MCP2035 NOTES: DS22304A-page 28 2012 Microchip Technology Inc. MCP2035 3.0 PIN DESCRIPTIONS Descriptions of the pins are listed in Table 3-1. TABLE 3-1: PIN FUNCTION TABLES MCP2035 TSSOP Symbol I/O/P 1 VSS P 2 CS I Function Ground Pin Chip Select Digital Input Pin 3 SCLK/ALERT I/O Clock input for the modified 3-wire SPI interface. ALERT output: This pin goes low if there is a parity error in the Configuration register or the 32 ms Alarm Timer is timed out. 4 RSSI O Received Signal Strength Indicator (RSSI) current output 5 NC N/A No Connect 6 LFDATA/CCLK/SDIO I/O Demodulated data output Carrier clock output Serial input or output data for the modified 3-wire SPI interface 7 VDD P Positive Supply Voltage Pin 8 VDD P Positive Supply Voltage Pin 9 NC N/A No Connect (Note 1) 10 NC N/A No Connect (Note 1) 11 LCX I 12 NC N/A Input pin for external LC antenna 13 LCCOM I Common reference input for the external LC antenna 14 VSS P Ground Pin No Connect Type Identification: I = Input; O = Output; P = Power Note 1: 3.1 This pin is bonded out to ground internally. Supply Voltage (VDD, VSS) The VDD pin is the power supply pin for the analog and digital circuitry within the MCP2035. This pin requires an appropriate bypass capacitor of 0.1 F. The voltage on this pin should be maintained in the 2.0V-3.6V range for specified operation. The VSS pin is the ground pin and the current return path for both analog and digital circuitry of the MCP2035. If an analog ground plane is available, it is recommended that this device be tied to the analog ground plane of the PCB. 3.2 Chip Select (CS) The CS pin needs to stay high when the device is receiving input signals. Leaving the CS pin low will place the device in the SPI Programming mode. 3.3 SPI Clock Input (SCLK/ALERT) This pin becomes the SPI clock input (SCLK) when CS is low, and becomes the ALERT output when CS is high. The ALERT pin is an open collector output. This pin has an internal pull-up resistor to ensure that no spurious SPI communication occurs between power-up and pin configuration of the MCU. 3.4 Received Signal Strength Indicator (RSSI) This pin becomes the Received Signal Strength Indicator (RSSI) output current sink when the RSSI output option is selected. The CS pin is an open collector output. This pin has an internal pull-up resistor to ensure that no spurious SPI communication occurs between power-up and pin configuration of the MCU. 2012 Microchip Technology Inc. DS22304A-page 29 MCP2035 3.5 Demodulated Data Output (LFDATA) Carrier Clock Output (CCLK) SPI Data I/O (SDIO) When the CS pin is high, this pin is an output pin for demodulated data or carrier clock, depending on output-type selection. When carrier clock output (CCLK) is selected, the LFDATA output is a square pulse of the input carrier clock and is available as soon as the AGC stabilization time (TSTAB) is completed. When the CS pin is low, this pin becomes the SPI data input and output (SDIO). 3.6 LCX Input This is the input pin of the LCX channel. An external LC resonance antenna circuit can be connected between the LCX and LCCOM pins. 3.7 LC Common Reference (LCCOM) This pin is the common reference input pin for the external LC resonant circuit. DS22304A-page 30 2012 Microchip Technology Inc. MCP2035 4.0 APPLICATION INFORMATION Microchip's MCP2030 and MCP2035 are stand-alone analog-front devices for low frequency (LF) signal detection and low-power/short range transponder applications. The MCP2035 is a single-channel device, while the MCP2030 is a three-channel device for more advanced applications. The device's high input sensitivity (1 mVPP) and ability to detect very weakly modulated input signals (as low as 8%), makes the device suitable for various intelligent short range transponder applications, such as Microchip's BodyCom applications. 4.1 MCP2035 BodyCom Application Example Figure 4-1 shows an example of a BodyCom system that is utilizing the human body as a signal transmission medium. The system has two units: (a) Base Station Unit and (b) Mobile Unit. An example of the BodyCom communication sequence is as follows: * This signal is then capacitively coupled to the human body, propagates and is detected by the Mobile Unit's high sensitivity MCP2035 front-end device. * The Mobile Unit processes the Base Station's command information, and responds back using a high frequency (HF, 8 MHz) carrier. * This respond signal is then received by the HF receiver in the Base Station, and demodulated and fed to another MCP2035 in the Base Station unit for digital waveforms. This return signal is then processed by the MCU in the Base Station. Figure 4-2 shows an example of the Mobile Unit schematics. This BodyCom solution can be used in various applications such as secure access control and passive keyless entry for automobiles. Note: See Microchip's Application Note AN1391 for more details of the BodyCom applications solutions. * When the human interfaces with the Base Station, it is initialized by an event of either touch or proximity, and the Base Station transmits a modulated 128 kHz command signal. Human Interface /Touch Pad MCP2035 (8 MHz) HF Transmitter (128 kHz) LF Driver Capacitive Coupling (128 kHz) Base Station Unit FIGURE 4-1: Medium. Capacitive Coupling MCU (PIC16LF1827) DSM (8 MHz) MCP2035 HF Receiver (Single-Channel Stand-alone Analog Front-End) PIC16LF1829 Microcontroller Mixer Mobile Unit BodyCom System Example Utilizing the Human Body as a Signal Transmission 2012 Microchip Technology Inc. DS22304A-page 31 MCP2035 MCP2035 VSS CS SCLK/ALERT PIC16LF1827 To ADC RSSI NC VSS Receiving Signal (128 kHz) LCCOM NC C L LCX NC LFDATA/CCLK/SDIO NC Data Signal Mod (fC = 8 MHz) RF Circuitry (HF TX) FIGURE 4-2: DS22304A-page 32 +3V VDD VDD +3V Transmitting Signal (8 MHz) Example of BodyCom Mobile Unit Implementation. 2012 Microchip Technology Inc. MCP2035 5.0 FUNCTIONAL DESCRIPTION AND THEORY OF DEVICE OPERATION Note: The MCP2035 contains an analog input channel for signal detection and LF talk-back. This section provides the functional description of the device. The input channel has internal tuning capacitors, sensitivity control circuits, an input signal strength limiter and an LF talk-back modulation transistor. An AGC loop is used for input channel gains. The output of the input channel is fed into a demodulator. The digital output is passed to the LFDATA pin. Figure 5-1 shows the block diagram of the device and Figure 5-2 shows the input signal path. There are a total of eight Configuration registers. Six of them are used for device operation options, one for column parity bits and one for status indication of device operation. Each register has nine bits including one row parity bit. These registers are readable and writable by SPI commands, except for the STATUS register, which is read-only. The device's features are dynamically controllable by programming the Configuration registers. 5.1 Modulation Circuit for LF Talk-Back The LF talk-back is achieved by turning on and off the modulation transistor. The modulation circuit consists of a modulation transistor (FET), internal tuning capacitors and external LC antenna components. The modulation transistor and the internal tuning capacitors are connected between the LCX input pin and LCCOM pin. Each LC input has its own modulation transistor. When the modulation transistor turns on, its low Turn-on Resistance (RM) clamps the induced LC antenna voltage. The coil voltage is minimized when the modulation transistor turns on, and maximized when the modulation transistor turns off. The modulation transistor's low turn-on resistance (RM) results in a high modulation depth. The modulation data comes from the external microcontroller section via the digital SPI as "Clamp On", "Clamp Off" commands. A basic block diagram of the modulation circuit is shown in Figure 5-1 and Figure 5-2. Tuning Capacitor The input tuning capacitor values are programmed by the Configuration registers up to 63 pF, 1 pF per step. Note: 5.4 The user can control the tuning capacitor by programming the Configuration registers. See Register 5-2 for details. Variable Attenuator The variable attenuator is used to attenuate, via AGC control, the input signal voltage to avoid saturating the amplifiers and demodulators. Note: RF Limiter The RF Limiter limits LC pin input voltage by de-Q'ing the external LC resonant antenna circuit. The limiter begins de-Q'ing the external LC antenna when the input voltage exceeds VDE_Q, progressively de-Q'ing harder to reduce the antenna input voltage. 5.2 5.3 The LF-Talk back is only used when it needs to communicate back to the Base Station using the same Base Station's low frequency (128 kHz) carrier frequency. A typically LF-Talk back range is up to a few inches. For the BodyCom applications, it uses HF (~8 MHz) for the return signal. 5.5 The variable attenuator function is accomplished by the device itself. The user cannot control its function. Sensitivity Control The sensitivity of the input channel can be reduced by the Configuration register sensitivity setting. This is used to desensitize the channel from optimum. Note: 5.6 The user can desensitize the channel sensitivity by programming the Configuration registers. See Register 5-5 for details. AGC Control The AGC controls the variable attenuator to limit the internal signal voltage to avoid saturation of internal amplifiers and demodulators (Refer to Section 5.4 "Variable Attenuator"). Note: 5.7 The AGC control function is accomplished by the device itself. The user cannot control its function. Fixed Gain Amplifiers 1 and 2 FGA1 and FGA2 provide a maximum two-stage gain of 40 dB. Note: The user cannot control the gain of these two amplifiers. The modulation FET is also shorted momentarily after Soft Reset and Inactivity Timer time-out. 2012 Microchip Technology Inc. DS22304A-page 33 MCP2035 5.8 Carrier Clock Detector The Carrier Clock Detector senses the input carrier cycles. The output of the detector switches digitally at the signal carrier frequency. Carrier clock output is available when the output is selected by the DATOUT bit in Configuration Register 1 (Register 5-2). 5.9 Demodulator The Demodulator consists of a full-wave rectifier, lowpass filter, peak detector and Data Slicer that detects the envelope of the input signal. 5.10 Data Slicer The Data Slicer consists of a reference generator and comparator. The Data Slicer compares the input with the reference voltage. The reference voltage comes from the minimum modulation depth requirement setting and input peak voltage. 5.11 Output Enable Filter The Output Enable Filter enables the LFDATA output once the incoming signal meets the wake-up sequence requirements (see Section 5.14 "Configurable Output Enable Filter"). 5.12 Received Signal Strength Indicator (RSSI) The RSSI provides a current which is proportional to the input signal amplitude (see Section 5.29.3 "Received Signal Strength Indicator (RSSI) Output"). 5.13 Analog Front-End Timers The device has an internal 32 kHz RC oscillator. The oscillator is used in several timers: * Inactivity Timer * Alarm Timer * Pulse Width Timer * Period Timer * AGC Settling Timer 5.13.1 RC OSCILLATOR The RC oscillator generates a 32 kHz internal clock. 5.13.2 INACTIVITY TIMER The Inactivity Timer is used to automatically return the device to Standby mode, if there is no input signal. The time-out period is approximately 16 ms (TINACT), based on the 32 kHz internal clock. The timer is reset when: * An amplitude change in the LF input signal, either high-to-low or low-to-high * CS pin is low (any SPI command) * Timer-related Soft Reset The timer starts after AGC initialization time (TAGC). The timer causes a Soft Reset when: * A previously received input signal does not change either high-to-low or low-to-high for TINACT The Soft Reset returns the device to Standby mode where most of the analog circuits, such as the AGC, demodulator and RC oscillator, are powered down. This returns the device to the lower Standby Current mode. 5.13.3 ALARM TIMER The Alarm Timer is used to notify the external MCU that the device is receiving an input signal that does not pass the output enable filter requirement. The time-out period is approximately 32 ms (TALARM) in the presence of continuing noise. The Alarm Timer time-out occurs if there is an input signal for longer than 32 ms that does not meet the output enable filter requirements. The Alarm Timer time-out causes: a) b) The ALERT pin to go low. The ALARM bit to set in the Status STATUS Register 7 (Register 5-8). The external MCU is informed of the Alarm Timer timeout by monitoring the ALERT pin. If the Alarm Timer time-out occurs, the external MCU can take appropriate actions, such as lowering channel sensitivity or disabling the input channel. If the noise source is ignored, the device can return to a lower standby current draw state. The timer is reset when the: * CS pin is low (any SPI command). * Output enable filter is disabled. * LFDATA pin is enabled (signal passed output enable filter). The timer starts after the AGC initialization time. The timer causes a low output on the ALERT pin when: * Output enable filter is enabled and modulated input signal is present for TALARM, but does not pass the output enable filter requirement. Note: The Alarm Timer is disabled if the output enable filter is disabled. The purpose of the Inactivity Timer is to minimize current draw by automatically returning to the lower current Standby mode, if there is no input signal for approximately 16 ms. DS22304A-page 34 2012 Microchip Technology Inc. MCP2035 5.13.4 PULSE WIDTH TIMER Note 1: The device needs a continuous and uninterrupted high input signal during AGC initialization time (TAGC). Any absence of signal during this time may reset the timer and a new input signal is needed for AGC settling time, or may result in an improper AGC gain setting, which will produce invalid output. The Pulse Width Timer is used to verify that the received output enable sequence meets both the minimum TOEH and minimum TOEL requirements. 5.13.5 PERIOD TIMER The Period Timer is used to verify that the received output enable sequence meets the maximum TOET requirement. 5.13.6 2: The rest of the device section wakes up if the input channel receives a signal with the AGC settling time correctly. STATUS Register 7 bit <2> (Register 5-8) indicates the status if the input channel wakes up. AGC INITIALIZATION TIMER (TAGC) This timer is used to keep the output enable filter in Reset while the AGC settles on the input signal. The time-out period is approximately 3.5 ms. At the end of this time (TAGC), the input should remain high (TPAGC), otherwise the counting is aborted and a Soft Reset is issued. See Figure 5-4 for details. LCX RF Lim Mod Tune X WAKEX / 64 AGC Detector Sensitivity Control X A Watchdog LCCOM B LCY (Note 1) 32 kHZ Oscillator Modulation Depth LCZ (Note 1) AGC Timer Output Enable Filter To Sensitivity X AGC Preserve Command Decoder/Controller To Modulation Transistors To Tuning Cap X Configuration Registers VSST Note 1: LCY and LCZ pads are internally grounded. FIGURE 5-1: VDDT RSSI SCLK/ALERT CS LFDATA/ CCLK/SDIO External MCU Functional Block Diagram. 2012 Microchip Technology Inc. DS22304A-page 35 MCP2035 DS22304A-page 36 AGC FGA1 LCX RF Limiter MOD FET Capacitor Tuning Sens. Control FGA2 Var. Atten. Carrier Detector LFDATA Output Enable Filter + > 4 VPP / 64 - 00 DETX DETY DETZ C /1 OR /4 01 LFDATA CLKDIV 10 RSSI GEN 11 A DATOUT WAKEX LCCOM 32 kHz Clock/AGC Timer WAKEY WAKEZ C 0.1V RSSI 1 0 0.4V Decode - LCY, LCZ (Note 1) Configuration Registers A Full-Wave Rectifier Low-Pass Filter X Y Peak Detector AGC Feedback Amplifier AGCACT + Z 2012 Microchip Technology Inc. Legend: FGA = Fixed Gain Amplifier FWR = Full-wave Rectifier LPF = Low-pass Filter PD = Peak Detector REF GEN MOD Depth Control CHX ACT Data Slicer Demodulator - Auto-Channel Selector X Y Z + Note 1: LCY and LCZ pads are internally grounded. FIGURE 5-2: AGCSIG Input Signal Path. AUTOCHSEL B MCP2035 5.14 The output enable filter consists of a high (TOEH) and low duration (TOEL) of a pulse immediately after the AGC settling gap time. The selection of high and low times further implies a max period time. The output enable high and low times are determined by SPI programming. Figure 5-3 and Figure 5-4 show the output enable filter waveforms. Configurable Output Enable Filter The purpose of this filter is to enable the LFDATA output and wake the external microcontroller only after receiving a specific sequence of pulses on the LC input pin. Therefore, it prevents waking up the external microcontroller due to noise or unwanted input signals. The circuit compares the timing of the demodulated header waveform with a pre-defined value, and enables the demodulated LFDATA output when a match occurs. Required Output Enable Sequence Start bit Data Packet TSTAB (TAGC + TPAGC) Demodulator Output There should be no missing cycles during TOEH. Missing cycles may result in failing the output enable condition. TGAP t TOEH Device Wake-up AGC and AGC Stabilization Gap Pulse FIGURE 5-3: t TOET t TOEL LFDATA output is enabled on this rising edge Output Enable Filter Timing. Start bit for data Demodulated LFDATA Output 3.5 ms LF Coil Input TPAGC TGAP Low Current (need Gap TAGC "high") Pulse Standby (AGC initialization time) Mode TSTAB (AFE Stabilization) t TOEL t 2 TE t TOEH t TOET Filter starts Filter is passed and LFDATA is enabled Legend: TAGC = AGC initialization time TGAP = AGC stabilization gap TPAGC = High time after TAGC TOEH = Minimum output enable filter high time TSTAB = AGC stabilization time (TAGC + TPAGC) TOEL = Minimum output enable filter low time TE = Time element of pulse (minimum pulse width) FIGURE 5-4: TOET = Maximum output enable filter period Output Enable Filter Timing Example (Detailed). 2012 Microchip Technology Inc. DS22304A-page 37 MCP2035 TABLE 5-1: * The received sequence exceeds the maximum TOET value: - TOEH + TOEL > TOET - or TOEH > TOET - or TOEL > TOET * A Soft Reset SPI command is received. OUTPUT ENABLE FILTER TIMING OEH <1:0> OEL <1:0> TOEH (ms) TOEL (ms) TOET (ms) 01 00 1 1 3 01 01 1 1 3 01 10 1 2 4 01 11 1 4 6 10 00 2 1 4 10 01 2 1 4 10 10 2 2 5 10 11 2 4 8 11 00 4 1 6 11 01 4 1 6 11 10 4 2 8 11 11 4 4 10 00 XX If the filter resets due to a long high-time (TOEH > TOET), the high-pulse timer will not begin timing again until after a gap of TE and another low-to-high transition occurs on the demodulator output. Disabling the output enable filter disables the TOEH and TOEL requirement and the device passes all detected data. See Figures 2-30, 2-31 and 2-32 for examples. When viewed from an application perspective, from the pin input, the actual output enable filter timing must factor in the analog delays in the input path (such as demodulator charge and discharge times). * TOEH - TDR + TDF * TOEL + TDR - TDF The output enable filter starts immediately after TGAP, the gap after AGC stabilization period. Filter Disabled The timing values of TOEH and TOEL are minimum and TOET is maximum at room temperature and VDD = 3.0V, 32 kHz oscillator. TOEH is measured from the rising edge of the demodulator output to the first falling edge. The pulse width must fall within TOEH t TOET. Note 1: TOEL is measured from the falling edge of the demodulator output to the rising edge of the next pulse. The pulse width must fall within TOEL t TOET. TOET is measured from rising edge to the next rising edge (i.e., the sum of TOEH and TOEL). The sum of TOEH and TOEL must be t TOET. If the Configuration Register 0 (Register 5-1), OEH<8:7> is set to `00', then the filter is disabled. See Figure 2-30 for this case. The filter will reset, requiring a complete new successive high and low period to enable LFDATA, under the following conditions. * The received high is not greater than the configured minimum TOEH value. * During TOEH, a loss of signal for longer than 56 s causes a filter Reset. * The received low is not greater than the configured minimum TOEL value. TABLE 5-2: 5.15 Input Sensitivity Control The device has typical input sensitivity of 3 mVPP. This means any input signal with amplitude greater than 3 mVPP can be detected. The internal AGC loop regulates the detecting signal amplitude when the input level is greater than approximately 20 mVPP. This signal amplitude is called "AGC-active level". The AGC loop regulates the input voltage so that the input signal amplitude range will be kept within the linear range of the detection circuits without saturation. The AGC Active Status bit (AGCACT<5>) in STATUS Register 7 (Register 5-8) is set if the AGC loop regulates the input voltage. Table 5-2 shows the input sensitivity comparison when the AGCSIG option is used. When AGCSIG option bit is set, the demodulated output is available only when the AGC loop is active (see Table 5-1). The channel input sensitivity can be reduced by setting the appropriate Configuration registers. Configuration Register 3 (Register 5-4), Configuration Register 4 (Register 5-5) and Configuration Register 5 (Register 5-6) have the option to reduce each channel gain from 0 dB to approximately -30 dB. INPUT SENSITIVITY VS. MODULATED SIGNAL STRENGTH SETTING (AGCSIG <7>) AGCSIG<7> (Config. Register 5) Description Input Sensitivity (Typical) 0 Option Disabled - Detect any input signal level (demodulated data and carrier clock) 3.0 mVPP 1 Option Enabled - No output until AGC Status = 1 (i.e., VPEAK 20 mVPP) (demodulated data and carrier clock) * Provides the best signal to noise ratio 20 mVPP DS22304A-page 38 2012 Microchip Technology Inc. MCP2035 5.16 Enable or Disable of Input Channel The Input channel can be enabled or disabled by programming the LCXEN bit in Configuration Register 0 (Register 5-1). When the input channel is enabled, it detects the input signal and provides output. When the channel is disabled, the device shuts down the input channel and provides no output, while saving current draws. The exact circuits disabled when an input is disabled are amplifiers, detector, full-wave rectifier, data slicer, and modulation FET. However, the RF input limiter remains active to protect the silicon from excessive antenna input voltages. 5.17 AGC Amplifier The circuit automatically amplifies input signal voltage levels to an acceptable level for the data slicer. Fast attacking and slow releasing by nature, the AGC tracks the carrier signal level and not the modulated data bits. The AGC requires an AGC initialization time (TAGC). The AGC will attempt to regulate the input channel's peak signal voltage into the data slicer to a desired regulated AGC voltage - reducing the input path's gain as the signal level attempts to increase above regulated AGC voltage, and allowing full amplification on signal levels below the regulated AGC voltage. The AGC has two modes of operation: * During the AGC initialization time (TAGC), the AGC time constant is fast, allowing a reasonably short acquisition time of the continuous input signal. * After TAGC, the AGC switches to a slower time constant for data slicing. Also, the AGC is frozen when the input signal envelope is low. The AGC tracks only high envelope levels. 5.18 AGC Preserve The AGC preserve feature is used to preserve the AGC value during the AGC initialization time (TAGC) and apply the value to the data slicing circuit for the following data streams instead of using a new tracking value. This feature is useful to demodulate the input signal correctly when the input has random amplitude variations at a given time period. This feature is enabled when the device receives an AGC Preserve On command and disabled if it receives an AGC Preserve Off command. Once the AGC Preserve On command is received, the device acquires a new AGC value during each AGC initialization time and preserves the value until a Soft Reset or an AGC Preserve Off command is issued. Therefore, it does not need to issue another AGC Preserve On command. An AGC Preserve Off command is needed to disable the AGC preserve feature (see Section 5.30.2.5 "AGC Preserve On Command" and Section 5.30.2.6 "AGC Preserve Off Command" for AGC Preserve commands). 2012 Microchip Technology Inc. 5.19 Soft Reset The Soft Reset is issued in the following events: a) b) c) d) After Power-on Reset (POR) After Inactivity Timer time-out If an "Abort" occurs After receiving SPI Soft Reset command The "Abort" occurs if there is no positive signal detected at the end of the AGC initialization period (TAGC). The Soft Reset initializes internal circuits and brings the device into a low current Standby mode operation. The internal circuits that are initialized by the Soft Reset include: * * * * Output Enable Filter AGC circuits Demodulator 32 kHz Internal Oscillator The Soft Reset has no effect on the Configuration register setup, except for some of the AFE STATUS Register 7 bits. (Register 5-8). The circuit initialization takes one internal clock cycle (1/32 kHz = 31.25 s). During the initialization, the modulation transistors between each input and LCCOM pins are turned-on to discharge any internal/ external parasitic charges. The modulation transistors are turned-off immediately after the initialization time. The Soft Reset is executed in Active mode only. It is not valid in Standby mode. 5.20 Minimum Modulation Depth Requirement for Input Signal The device demodulates the modulated input signal if the modulation depth of the input signal is greater than the minimum requirement that is programmed in Configuration Register 5 (Register 5-6). Figure 5-5 shows the definition of the modulation depth and examples. MODMIN<6:5> of the Configuration Register 5 offer four options. They are 60%, 33%, 14% and 6%. The default setting is 33%. The purpose of this feature is to enhance the demodulation integrity of the input signal. The 6% setting is the best choice for the input signal with weak modulation depth, which is typically observed near the high-voltage Base Station antenna and also at fardistance from the Base Station antenna. It gives the best demodulation sensitivity, but is very susceptible to noise spikes that can result in a bit detection error. The 60% setting can reduce the bit errors caused by noise, but gives the least demodulation sensitivity. See Table 5-3 for minimum modulation depth requirement settings. DS22304A-page 39 MCP2035 TABLE 5-3: SETTING FOR MINIMUM MODULATION DEPTH REQUIREMENT MODMIN Bits (Config. Register 5) Modulation Depth Bit 6 Bit 5 0 0 33% (default) 0 1 60% 1 0 14% 1 1 8% (a) Modulation Depth Definition Amplitude Modulation Depth (%) = Input Signal B t A-B X 100% A+B A (b) Input signal vs. minimum modulation depth setting vs. LFDATA output Amplitude 7 mVPP 10 mVPP Coil Input Strength Modulation Depth (%) = t Input Signal 10 - 7 X 100% = 17.64% 10 + 7 Input signal with modulation depth = 17.64% Demodulated LFDATA Output when MODMIN Setting = 14% t (LFDATA output = toggled) Amplitude 0 FIGURE 5-5: DS22304A-page 40 Demodulated LFDATA Output if MODMIN Setting = 33% (LFDATA output = not toggled) t Modulation Depth Examples. 2012 Microchip Technology Inc. MCP2035 5.21 Low-Current Sleep Mode 5.24 The device can stay at an ultra low-current mode (Sleep mode) when it receives a Sleep command via the Serial Peripheral Interface (SPI). All circuits including the RF Limiter, except the minimum circuitry required to retain register memory and SPI capability, will be powered down to minimize the current draw. Power-on Reset or any SPI command, other than the Sleep command, is required to wake the device from Sleep. 5.22 The Configuration registers are volatile memory. Therefore, the contents of the registers can be corrupted or cleared by any electrical incidence, such as battery disconnect. To ensure data integrity, the device has an error detection mechanism using row and column parity bits of the Configuration register memory map. The bit 0 of each register is a row parity bit which is calculated over the eight Configuration bits (from bit 1 to bit 8). The Column Parity Register (Configuration Register 6) holds column parity bits; each bit is calculated over the respective columns (Configuration registers 0 to 5) of the Configuration bits. The STATUS register is not included for the column parity bit calculation. Parity is to be odd. The parity bit, set or cleared, makes an odd number of set bits. The user needs to calculate the row and column parity bits using the contents of the registers and program them. During operation, the device continuously calculates the row and column parity bits of the configuration memory map. If a parity error occurs, the device lowers the SCLK/ALERT pin (interrupting the microcontroller section) indicating the configuration memory has been corrupted or unloaded and needs to be reprogrammed. Low-Current Standby Mode The device is in Standby mode when no input signal is present on the input pin, but is powered and ready to receive any incoming signals. 5.23 Error Detection of Configuration Register Data Low-Current Active Mode The device is in Low-Current Active mode when an input signal is present on any input pin and internal circuitry is switching with the received data. At an initial condition after a Power-on Reset, the values of the registers are all clear (default condition). Therefore, the device will issue the parity bit error by lowering the SCLK/ALERT pin. If the user reprograms the registers with the correct parity bits, the SCLK/ ALERT pin will be toggled to logic high level immediately. The parity bit errors do not change or affect any functional operation. Table 5-4 shows an example of the register values and corresponding parity bits. TABLE 5-4: CONFIGURATION REGISTER PARITY BIT EXAMPLE Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (Row Parity) Configuration Register 0 1 0 1 0 1 0 0 0 0 Configuration Register 1 0 0 0 0 0 0 0 0 1 Configuration Register 2 0 0 0 0 0 0 0 0 1 Configuration Register 3 0 0 0 0 0 0 0 0 1 Configuration Register 4 0 0 0 0 0 0 0 0 1 Configuration Register 5 1 0 0 0 0 0 0 0 0 Configuration Register 6 (Column Parity Register) 1 1 0 1 0 1 1 1 1 Register Name 2012 Microchip Technology Inc. DS22304A-page 41 MCP2035 5.25 Factory Calibration 5.27 The device is calibrated during probe test to reduce the device-to-device variation in standby current, internal timing and sensitivity, as well as channel-to-channel sensitivity variation. 5.26 Demodulator The demodulator recovers the modulation data from the received signal, containing carrier plus data, by appropriate envelope detection. The demodulator has a fast rise (charge) time (TDR) and a fall time (TDF) appropriate to an envelope of input signal (see Section 1.0 "Electrical Specifications" for TDR and TDF specifications). The demodulator contains the full-wave rectifier, low-pass filter, peak detector and data slicer. De-Q'ing of Antenna Circuit When the transponder is close to the Base Station, the transponder coil may develop coil voltage higher than VDE_Q. This condition is called "near field". The device detects the strong near field signal through the AGC control, and de-Q'ing the antenna circuit to reduce the input signal amplitude. Input at LC input pin Full-wave Rectifier output Demodulated LFDATA output TDR FIGURE 5-6: 5.28 TDF Demodulator Charge and Discharge. Power-On Reset 5.29.1 DEMODULATOR OUTPUT This circuit remains in a Reset state until a sufficient supply voltage is applied. The Reset releases when the supply is sufficient for correct device operation, nominally VPOR. The demodulator output is the default configuration of the output selection. This is the output of an envelope detection circuit. See Figure 5-6 for the demodulator output. The Configuration registers are all cleared on a Power-on Reset. As the Configuration registers are protected by odd row and column parity, the ALERT pin will be pulled down - indicating to the external microcontroller section that the configuration memory is cleared and requires new programming. When the demodulated output is selected, the output is available in two different conditions depending on how the options of Configuration Register 0 (Register 5-1) are set: Output Enable Filter is disabled or enabled. See Section 2.0 "Typical Performance Curves" for various demodulated data output. Related Configuration register bits: 5.29 LFDATA Output Selection The device output is available only when the input channel is enabled (LCXEN = Enabled in Configuration Register 0). The LFDATA output can be configured to pass the Demodulator output, Received Signal Strength Indicator (RSSI) output, or Carrier Clock (CCLK). See Configuration Register 1 (Register 5-2) for more details. DS22304A-page 42 * Configuration Register 1 (Register 5-2), DATOUT <8:7>: bit 8 bit 7 0 0: Demodulator Output 0 1: Carrier Clock Output 1 0: RSSI Output 0 1: RSSI Output * Configuration Register 0 (Register 5-1): all bits 2012 Microchip Technology Inc. MCP2035 5.29.2 CARRIER CLOCK OUTPUT When the carrier clock output is selected, the LFDATA output is a square pulse of the input carrier clock and available as soon as the AGC stabilization time (TAGC) is completed. There are two Configuration register options for the carrier clock output: (a) clock divide-by one or (b) clock divide-by four, depending on bit DATOUT<7> of Configuration Register 2 (Register 5-3). The carrier clock output is available immediately after the AGC settling time. The Output Enable Filter, AGCSIG, and MODMIN options are applicable for the carrier clock output in the same way as the demodulated output. See Figure 2-32 for carrier clock output examples. Related Configuration register bits: * Configuration Register 1 (Register 5-2), DATOUT <8:7>: The RSSI output current is linearly proportional to the input signal strength. There are variations between device to device. See Figure 2-13 for examples. The linearity (ILRRSSI) of the RSSI output current is tested by sampling the outputs for three input points: 37 mVPP, 100 mVPP, and 370 mVPP. The RSSI output current for 100 mVPP of input signal is compared with the expected output current obtained from the line that is connecting the two endpoints (37 mVPP and 370 mVPP). Equation 5-1 and Figure 5-7 show the details for the RSSI linearity specification. EQUATION 5-1: ILRRSSI(%) = Deviation at 100 mVPP of Input Signal 0: Demodulator Output 1: Carrier Clock Output 0: RSSI Output 1: RSSI Output * Configuration Register 2 (Register 5-3), CLKDIV<7>: 0: Carrier Clock/1 1: Carrier Clock/4 Where: * Deviation at 100 mVPP of Input Signal = [IRSSI measured - IRSSI expected] at 100 mVPP of input signal. * IRSSI expected = RSSI current obtained from the line that is connecting two endpoints (RSSI output currents for 37 mVPP and 370 mVPP of input). * Configuration Register 0 (Register 5-1): all bits are affected * Configuration Register 5 (Register 5-6) RECEIVED SIGNAL STRENGTH INDICATOR (RSSI) OUTPUT An analog current output is available at the RSSI pin when the Received Signal Strength Indicator (RSSI) output is selected by the Configuration register. The analog current is linearly proportional to the input signal strength. All timers in the circuit, such as the Inactivity Timer, Alarm Timer, and AGC initialization time, are disabled during the RSSI mode. Therefore, the RSSI output is not affected by the AGC stabilization time, and available immediately when the RSSI option is selected. The device enters Active mode immediately when the RSSI output is selected. y y = a+bx RSSI Output Current [A] 5.29.3 x 100% IRSSI for 370 mVPP of Input Signal bit 8 bit 7 0 0 1 1 RSSI LINEARITY SPECIFICATION = Measured = Expected d = Deviation d 37 mVPP 100 mVPP 370 mVPP x Input Signal Amplitude FIGURE 5-7: Example. RSSI Linearity Test When the device receives an SPI command during the RSSI output, the RSSI mode is temporarily disabled until the SPI communication is completed. It returns to the RSSI mode again after the SPI communication is completed. The RSSI mode is held until another output type is selected (CS low turns off the RSSI signal). 2012 Microchip Technology Inc. DS22304A-page 43 MCP2035 5.29.3.1 Related Configuration register bits: * Configuration Register 1 (Register 5-2), DATOUT<8:7>: bit 8 0 0 1 1 bit 7 0: Demodulated Output 1: Carrier Clock Output 0: RSSI Output 1: RSSI Output * Configuration Register 2 (Register 5-3), RSSIFET<8>: 0: Pull-Down MOSFET off 1: Pull-Down MOSFET on. Note: The pull-down MOSFET option is valid only when the RSSI output is selected. The MOSFET is not controllable by users when demodulated or carrier clock output option is selected. * Configuration Register 0 (Register 5-1): all bits are affected. The RSSI output is an analog current. It needs an external Analog-to-Digital (ADC) data conversion device for digitized output. The ADC data conversion can be accomplished by using a stand-alone external ADC device, an external MCU that has internal ADC features, or an external MCU that has no ADC features but instead uses firmware. The RSSIFET is used to discharge any external charge on the LFDATA pin in the RSSI Output mode. The MOSFET can be turned on or off with bit RSSIFET<8> of Configuration Register 2 (Register 5-3). When it is turned on, the internal MOSFET provides a discharge path for the external capacitor that is connected at the LFDATA pin. This MOSFET option is valid only if RSSI output is selected and not controllable by users for demodulated or carrier clock output options. See separate application notes for various external ADC implementation methods for this device. See Figure 5-8 for RSSI output path. 5.30 RSSI Output Current Generator 5.30.1 Current Output VDD Off if RSSI active RSSI Pin LFDATA/CCLK Pin RSSIFET(1) RSSI Pull-down MOSFET (controlled by Config. 2, bit 8) Note 1: The RSSIFET is used to discharge any external capacitor that is connected at the LFDATA pin. FIGURE 5-8: DS22304A-page 44 RSSI Output Path. ANALOG-TO-DIGITAL DATA CONVERSION OF RSSI SIGNAL Configuration Registers SPI COMMUNICATION The SPI communication is used to read from or write to the Configuration registers and to send command-only messages. Three pins are used for SPI communication: CS, SCLK/ALERT, and LFDATA/RSSI/ CCLK/SDIO. Figure 5-9, Figure 5-10 and Figure 5-11 show examples of the SPI communication sequences. When these pins are connected to the external MCU I/O pins, the following are needed: CS * Pin is permanently an input with an internal pull-up. SCLK/ALERT * Pin is an open collector output when CS is high. An internal pull-up resistor exists to ensure no spurious SPI communication between powering and the MCU configuring its pins. This pin becomes the SPI clock input when CS is low. LFDATA/CCLK/SDIO * Pin is a digital output (LFDATA) so long as CS is high. During SPI communication, the pin is the SPI data input (SDI) unless performing a register Read, where it will be the SPI data output (SDO). 2012 Microchip Technology Inc. Driving CS high MCU pin output MCU pin is input. SCLK pulled high by internal pull-up CS CS pulled high by internal pull-up MCU pin is input. MCP2035 SCLK/ALERT MCU pin is input. ALERT (open collector output) LFDATA/CCLK/SDIO FIGURE 5-9: LFDATA (output) Power-Up Sequence. 1 LFDATA (output) TSU MCU pin still Input LFDATA/CCLK/SDIO MSb SCLK (input) SDI (input) 3 1/FSCLK TCS1 LSb THD 5 7 ALERT (output) TCS0 Driven low by MCU ALERT (output) TSCCS Driven low by MCU SCLK/ALERT 4 16 Clocks for Write Command, Address and Data THI TLO MCU pin to Output Driven low by MCU TCSSC MCU pin to Input CS 6 MCU pin to Input TCSH 2 LFDATA (output) MCU SPI Write Details: 1. 2. 3. 4. 5. 6. 7. FIGURE 5-10: Drive the open collector ALERT output low * To ensure no false clocks occur when CS drops Drop CS * SCLK/ALERT becomes SCLK input * LFDATA/CCLK/SDIO becomes SDI input Change LFDATA/CCLK/SDIO connected pin to output * Driving SPI data Clock in 16-bit SPI Write sequence - command, address, data and parity bit * Command, address, data and parity bit Change LFDATA/CCLK/SDIO connected pin to input Raise CS to complete the SPI Write Change SCLK/ALERT back to input SPI Write Sequence. 2012 Microchip Technology Inc. DS22304A-page 45 MCP2035 TCSH 1 ALERT (output) 8 16 Clocks for Read Result 10 TCSSC TCS1 SCLK (input) ALERT (output) TCS0 Driven low by MCU LSb 1/FSCLK TCSSC Driven low by MCU MSb SCLK (input) TCS0 MCU pin still Input TSU THD LFDATA/RSSI/ CCLK/SDIO SDI (input) LFDATA (output) 3 MCU pin to Input ALERT (output) MCU pin to Output SCLK/ALERT Driven low by MCU THI TLO MCU pin to Input TSCCS TCS1 Driven low by MCU 4 16 Clocks for Read Command, Address and Dummy Data TCSSC 9 7 MCU pin to Input 6 2 CS TCSH 5 TDO LFDATA (output) SDO (output) LFDATA (output) MCU SPI Read Details: 1. Drive the open collector ALERT output low * To ensure no false clocks occur when CS drops 2. Drop CS * SCLK/ALERT becomes SCLK input * LFDATA/CCLK/SDIO becomes SDI input 3. Change LFDATA/CCLK/SDIO connected pin to output * Driving SPI data 4. Clock in 16-bit SPI Read sequence * Command, address and dummy data 5. Change LFDATA/CCLK/SDIO connected pin to input 6. Raise CS to complete the SPI Read entry of command and address 7. Drop CS * AFE SCLK/ALERT becomes SCLK input * LFDATA/CCLK/SDIO becomes SDO output 8. Clock out 16-bit SPI Read result * First seven bits clocked-out are dummy bits * Next eight bits are the Configuration register data * The last bit is the Configuration register row parity bit 9. Raise CS to complete the SPI Read 10. Change SCLK/ALERT back to input Note: The TCSH is considered as one clock. Therefore, the Configuration register data appears at 6th clock after TCSH. FIGURE 5-11: DS22304A-page 46 SPI Read Sequence. 2012 Microchip Technology Inc. MCP2035 5.30.2 COMMAND DECODER/ CONTROLLER The circuit executes eight SPI commands from the external MCU. The command structure is: Command (3 bits) + Configuration Address (4 bits) + Data Byte and Row Parity Bit with the Most Significant bit first. Table 5-5 shows the available SPI commands. TABLE 5-5: The device operates in SPI mode 0,0. In mode 0,0 the clock idles in the low state (Figure 5-12). SDI data is loaded into the device on the rising edge of SCLK and SDO data is clocked out on the falling edge of SCLK. There must be multiples of 16 clocks (SCLK) while CS is low or commands will abort. SPI COMMANDS Command Address Data Row Parity Description Command only - Address and Data are "Don't Care", but need to be clocked in regardless. 000 XXXX XXXX XXXX X Clamp on - enable modulation circuit 001 XXXX XXXX XXXX X Clamp off - disable modulation circuit 010 XXXX XXXX XXXX X Enter Sleep mode (any other command wakes the AFE) 011 XXXX XXXX XXXX X AGC Preserve On - to temporarily preserve the current AGC level 100 XXXX XXXX XXXX X AGC Preserve Off - AGC again tracks strongest input signal 101 XXXX XXXX XXXX X Soft Reset - resets various circuit blocks Read Command - Data will be read from the specified register address. 110 0000 Config Byte 0 P General - options that may change during normal operation 0001 Config Byte 1 P Input channel (LCX) antenna tuning and LFDATA output format 0010 Config Byte 2 P RSSIFET Condition and CLKDIV settings 0011 Config Byte 3 P Not used 0100 Config Byte 4 P Input channel (LCX) sensitivity reduction 0101 Config Byte 5 P Modulation depth and AGC loop 0110 Column Parity P Column parity byte for Config Byte 0 -> Config Byte 5 0111 Status X The device's internal operation status and parity error indication bits Write Command - Data will be written to the specified register address. 111 Note: 0000 Config Byte 0 P Output enable filter, channel enable/disable, etc. 0001 Config Byte 1 P Input channel (LCX) antenna tuning and LFDATA output type 0010 Config Byte 2 P RSSIFET, CLKDIV 0011 Config Byte 3 P Write all bits to "0s" 0100 Config Byte 4 P Input channel (LCX) sensitivity reduction 0101 Config Byte 5 P AGCSIG, MODMIN 0110 Column Parity P Column parity byte (odd parity) for Configuration Bytes 0 to 5 0111 Not Used X Register is readable, but not writable `P' denotes the row parity bit (odd parity) for the respective data byte. 2012 Microchip Technology Inc. DS22304A-page 47 MCP2035 CS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 SCLK MSb LSb Command FIGURE 5-12: 5.30.2.1 Clamp On Command Clamp Off Command Sleep Command This command places the device in Sleep mode - minimizing current draw by disabling all but the essential circuitry. Any other command wakes the device from Sleep (e.g., Clamp Off command). 5.30.2.4 Soft Reset Command The device issues a Soft Reset when it receives an external Soft Reset command. The external Soft Reset command is typically used to end a SPI communication sequence or to initialize the device for the next signal detection sequence, etc. See Section 5.19 "Soft Reset" for more details on Soft Reset. If a Soft Reset command is sent during a "Clamp-on" condition, the device still keeps the "Clamp-on" condition after the Soft Reset execution. The Soft Reset is executed in Active mode only, not in Standby mode. The SPI Soft Reset command is ignored if the device is not in Active mode. DS22304A-page 48 bit 0 bit 1 Row Parity Bit Detailed SPI Timing (AFE). This command results in deactivating (turning off) the modulation transistor of input channel. 5.30.2.3 Data Byte Address This command results in activating (turning on) the modulation transistor of the input channel. 5.30.2.2 bit 8 bit 0 bit 3 bit 0 bit 2 SDIO 5.30.2.5 AGC Preserve On Command This command results in preserving the AGC level during each AGC initialization time and applies the value to the data slicing circuit for the following data stream. The preserved AGC value is reset by a Soft Reset, and a new AGC value is acquired and preserved when it starts a new AGC initialization time. This feature is disabled by an AGC Preserve Off command (see Section 5.18 "AGC Preserve"). 5.30.2.6 AGC Preserve Off Command This command disables the AGC preserve feature and returns to the normal AGC tracking mode, fast tracking during AGC settling time and slow tracking after that (see Section 5.18 "AGC Preserve"). 5.30.3 READ/WRITE COMMANDS FOR CONFIGURATION REGISTERS The device includes eight Configuration registers, including a Column Parity register and STATUS register. All registers are readable and writable via SPI commands, except the STATUS register, which is readonly. Bit 0 of each register is a row parity bit (except for STATUS Register 7) that makes the register contents an odd number ("1") including the parity bit itself. Note: If the odd parity bits for the row and column are incorrectly programmed, the Parity Error Indicator (PEI) bit in the Status Register 7 is set ("1") and the ALERT output pin will pull low, which causes extra current draws. 2012 Microchip Technology Inc. MCP2035 5.30.3.1 STATUS Register The status register indicates the operation condition of the MCP2035 device after various SPI commands and Power-on Reset. See Table 5-7 for more details. TABLE 5-6: CONFIGURATION REGISTERS SUMMARY Register Name Bit 8 Bit 7 Configuration Register 0 OEH Configuration Register 1 DATOUT Configuration Register 2 RSSIFET Bit 6 Bit 5 OEL Bit 0 ALRTIND 1 (Note 1) 1 (Note 1) LCXEN R0PAR R2PAR Write to all 0's (Note 1) R3PAR Configuration Register 4 Input Channel (LCX) Sensitivity Control MODMIN MODMIN Column Parity Bit Register 6 STATUS Register 7 Bit 1 Write to all 0's (Note 1) CLKDIV AGCSIG Bit 2 R1PAR Unimplemented 0 (Note 1) Bit 3 Input Channel (LCX) Tuning Capacitor Configuration Register 3 Configuration Register 5 Bit 4 Write to all 0's (Note 1) R4PAR Write to all 0's (Note 1) R5PAR Column Parity Bits Active Channel Indicators AGCACT Wake-up Channel Indicators R6PAR ALARM PEI Note 1: The values in the colored area are strongly recommended for the best result. 2: The user must compute the odd row parity bit (bit 0 of each row) and odd column parity bits in the Column Parity Bit Register 6, and program them the same as other configuration registers. 3: STATUS Register is read only register. 2012 Microchip Technology Inc. DS22304A-page 49 MCP2035 REGISTER 5-1: CONFIGURATION REGISTER 0 (ADDRESS: 0000) R/W-0 OEH1 bit 8 R/W-0 R/W-0 OEH0 OEL1 R/W-0 OEL0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ALRTIND 1 1 LCXEN R0PAR bit7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 8-7 OEH<1:0>: Output Enable Filter High Time (TOEH) bit 00 = Output Enable Filter disabled (no wake-up sequence required, passes all signals to LFDATA) 01 = 1 ms 10 = 2 ms 11 = 4 ms bit 6-5 OEL<1:0>: Output Enable Filter Low Time (TOEL) bit 00 = 1 ms 01 = 1 ms 10 = 2 ms 11 = 4 ms bit 4 ALRTIND: ALERT bit, output triggered by: 1 = Parity error and/or expired Alarm Timer (receiving noise, see Section 5.13.3 "Alarm Timer") 0 = Parity error bit 3-2 Write these two bits to all "1". (Note 1) bit 1 LCXEN: Input Channel (LCX) Enable bit 1 = Disabled 0 = Enabled bit 0 R0PAR: Register 0 Parity bit - set or cleared (1 or 0) so the 9-bit register contains odd parity - an odd number of set bits. An incorrect parity bit may draw unnecessary extra current. Note 1: Writing these bits to "1" ensures disabling of internally grounded unused channels (LCY and LCZ), which guarantees minimizing any current draw through the unused internal channels. DS22304A-page 50 2012 Microchip Technology Inc. MCP2035 REGISTER 5-2: CONFIGURATION REGISTER 1 (ADDRESS: 0001) R/W-0 DATOUT1 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 DATOUT0 LCXTUN5 LCXTUN4 LCXTUN3 LCXTUN2 LCXTUN1 LCXTUN0 R1PAR bit7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 8-7 DATOUT<1:0>: LFDATA Output type bit 00 = Demodulated output 01 = Carrier clock output 10 = RSSI output 11 = RSSI output bit 6-1 LCXTUN<5:0>: LCX Tuning Capacitance bit 000000 = +0 pF (Default) x = Bit is unknown * * 111111 = +63 pF bit 0 R1PAR: Register 1 Parity Bit - set or cleared (1 or 0) so the 9-bit register contains odd parity - an odd number of set bits. An incorrect parity bit may draw unnecessary extra current. REGISTER 5-3: CONFIGURATION REGISTER 2 (ADDRESS: 0010) R/W-0 RSSIFET bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CLKDIV 0 0 0 0 0 0 R2PAR bit7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 8 RSSIFET: Pull-down MOSFET on LFDATA pad bit (controllable by user in the RSSI mode only) 1 = Pull-down RSSI MOSFET on 0 = Pull-down RSSI MOSFET off bit 7 CLKDIV: Carrier Clock Divide-by bit 1 = Carrier clock/4 0 = Carrier clock/1 bit 6-1 Recommended to all 0's. (Note 1) bit 0 R2PAR: Register 2 Parity bit - set or cleared (1 or 0) so the 9-bit register contains odd parity - an odd number of set bits. An incorrect parity bit may draw unnecessary extra current. Note 1: These bits are associated to the internally grounded LCY tuning capacitors, and have no effect in the MCP2035. 2012 Microchip Technology Inc. DS22304A-page 51 MCP2035 REGISTER 5-4: CONFIGURATION REGISTER 3 (ADDRESS: 0011) U-0 bit 8 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 0 0 0 0 0 0 R3PAR bit7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 8-7 Unimplemented: Read as `0' bit 6-1 Recommended to all 0's. (Note 1) bit 0 R3PAR: Register 3 Parity Bit - set or cleared (1 or 0) so the 9-bit register contains odd parity - an odd number of set bits. An incorrect parity bit may draw unnecessary extra current. Note 1: These bits are associated to the internally grounded LCZ tuning capacitors, and have no effect in the MCP2035. DS22304A-page 52 2012 Microchip Technology Inc. MCP2035 REGISTER 5-5: CONFIGURATION REGISTER 4 (ADDRESS: 0100) R/W-0 LCXSEN3 bit 8 R/W-0 R/W-0 LCXSEN2 LCXSEN1 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 LCXSEN0 0 0 0 0 R4PAR bit7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 8-5 LCXSEN<3:0>: Typical Input Channel (LCX) Sensitivity Reduction bit. (Note 1) 0000 = -0 dB (Default) 0001 = -2 dB 0010 = -4 dB 0011 = -6 dB 0100 = -8 dB 0101 = -10 dB 0110 = -12 dB 0111 = -14 dB 1000 = -16 dB 1001 = -18 dB 1010 = -20 dB 1011 = -22 dB 1100 = -24 dB 1101 = -26 dB 1110 = -28 dB 1111 = -30 dB bit 4-1 Recommended to all 0's. (Note 2) bit 0 R4PAR: Register 4 Parity bit - set or cleared (1 or 0) so the 9-bit register contains odd parity - an odd number of set bits. An incorrect parity bit may draw unnecessary extra current. Note 1: 2: Assured monotonic increment (or decrement) by design. These bits are associated to the internally grounded LCY sensitivity control, and have no effect in the MCP2035. 2012 Microchip Technology Inc. DS22304A-page 53 MCP2035 REGISTER 5-6: CONFIGURATION REGISTER 5 (ADDRESS: 0101) R/W-0 0 bit 8 R/W-0 R/W-0 AGCSIG MODMIN1 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 MODMIN0 0 0 0 0 R5PAR bit7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 8 Recommended to write `0': This bit has no effect in the MCP2035. bit 7 AGCSIG: Demodulator Output Enable bit, after the AGC loop is active 1 = Enabled - No output until AGC is regulating at around 20 mVPP at input pin. The AGC Active Status bit is set when the AGC begins regulating. 0 = Disabled - The device passes signal of any level it is capable of detecting bit 6-5 MODMIN<1:0>: Minimum Modulation Depth bit 00 = 33% 01 = 60% 10 = 14% 11 = 8% bit 4-1 Recommended to all 0's. (Note 1) bit 0 R5PAR: Register 5 Parity bit - set or cleared (1 or 0) so the 9-bit register contains odd parity - an odd number of set bits. An incorrect parity bit may draw unnecessary extra current. Note 1: These bits are associated to the internally grounded LCZ sensitivity control. DS22304A-page 54 2012 Microchip Technology Inc. MCP2035 REGISTER 5-7: COLUMN PARITY REGISTER 6 (ADDRESS: 0110) R/W-0 COLPAR7 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 COLPAR6 COLPAR5 COLPAR4 COLPAR3 COLPAR2 COLPAR1 COLPAR0 R6PAR bit7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 8 COLPAR7: Set or Cleared (1 or 0) so that this 8th parity bit (COLPAR7) + the sum of the Config. register row parity bits contain an odd number of set ("1") bits. bit 7 COLPAR6: Set or Cleared (1 or 0) such that this 7th parity bit (COLPAR6) + the sum of the 7th bits in Config. registers 0 through 5 contain an odd number of set ("1") bits. bit 6 COLPAR5: Set or Cleared (1 or 0) such that this 6th parity bit (COLPAR5) + the sum of the 6th bits in Config. registers 0 through 5 contain an odd number of set ("1" ) bits. bit 5 COLPAR4: Set or Cleared (1 or 0) such that this 5th parity bit (COLPAR4) + the sum of the 5th bits in Config. registers 0 through 5 contain an odd number of set ("1") bits. bit 4 COLPAR3: Set or Cleared (1 or 0) such that this 4th parity bit (COLPAR3) + the sum of the 4th bits in Config. registers 0 through 5 contain an odd number of set ("1") bits. bit 3 COLPAR2: Set or Cleared (1 or 0) such that this 3rd parity bit (COLPAR2) + the sum of the 3rd bits in Config. registers 0 through 5 contain an odd number of set ("1") bits. bit 2 COLPAR1: Set or Cleared (1 or 0) such that this 2nd parity bit (COLPAR1) + the sum of the 2nd bits in Config. registers 0 through 5 contain an odd number of set ("1") bits. bit 1 COLPAR0: Set or Cleared (1 or 0) such that this 1st parity bit (COLPAR0) + the sum of the 1st bits in Config. registers 0 through 5 contain an odd number of set ("1") bits. bit 0 R6PAR: Register 6 Parity bit - Set or Cleared (1 or 0) so the 9-bit register contains odd ("1") parity - an odd number of set ("1") bits Note 1: The parity bits are calculated from the configuration registers from 0 to 6 and programmed by the user. An incorrect parity bit can cause unnecessary extra current draws although the device may function correctly. 2012 Microchip Technology Inc. DS22304A-page 55 MCP2035 REGISTER 5-8: STATUS REGISTER 7 (ADDRESS: 0111) R-0 CHZACT bit 8 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 CHYACT CHXACT AGCACT WAKEZ WAKEY WAKEX ALARM PEI bit7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 8 CHZACT: This bit has no meaning in the MCP2035. Therefore, ignore this bit. This bit can be cleared via Soft Reset. bit 7 CHYACT: This bit has no meaning in the MCP2035. Therefore, ignore this bit. This bit can be cleared via Soft Reset bit 6 CHXACT: Input Channel (LCX) Active bit (cleared via Soft Reset). (Note 1) 1 = Input Channel (LCX) is passing data after TAGC 0 = Input Channel (LCX) is not passing data after TAGC bit 5 AGCACT: AGC Active Status bit (real time, cleared via Soft Reset) 1 = AGC is active (Input signal is strong). AGC is active when input signal level is approximately > 20 mVPP range. 0 = AGC is inactive (Input signal is weak) bit 4-3 This bit has no meaning, and can be cleared via Soft Reset. bit 2 WAKEX: Wake-up Channel X Indicator Status bit (cleared via Soft Reset) 1 = Input Channel (LCX) caused a device wake-up (passed 64 clock counter) 0 = Input Channel (LCX) did not cause a device wake-up bit 1 ALARM: Indicates whether an Alarm Timer time-out has occurred (cleared via read "STATUS Register command") 1 = The Alarm Timer time-out has occurred. It may cause the ALERT output to go low depending on the state of bit 4 of the Configuration register 0 0 = The Alarm Timer is not timed out bit 0 PEI: Parity Error Indicator bit - indicates whether a Configuration register parity error has occurred (real time) 1 = A parity error has occurred and caused the ALERT output to go low 0 = A parity error has not occurred Note 1: Bit is high whenever channel is passing data. Bit is low in Standby mode. DS22304A-page 56 2012 Microchip Technology Inc. MCP2035 TABLE 5-7: STATUS REGISTER BIT CONDITION (AFTER POWER-ON RESET AND VARIOUS SPI COMMANDS) Bit 8 (Note 2) Bit 7 (Note 2) Bit 6 Condition Input (CHX) ACT CHZACT CHYACT Bit 5 Bit 4 Bit 3 (Note 2) (Note 2) Bit 2 Bit 1 AGCACT WAKEZ WAKEY WAKEX ALARM Bit 0 PEI POR 0 0 0 0 0 0 0 0 1 Read Command (STATUS Register only) u u u u u u u 0 u Sleep Command u u u u u u u u u Soft Reset Executed (Note 1) 0 0 0 0 0 0 0 u u Legend: u = unchanged Note 1: See Section 5.19 "Soft Reset" and Section 5.30.2.4 "Soft Reset Command" for the condition of Soft Reset execution. 2: These bits have no meaning and are ignored in the MCP2035. TABLE 5-8: EXAMPLE OF SELECTING CONFIGURATION REGISTER BIT VALUES AND PARITY BITS Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (Calculate d Row Parity Bit) Config. Reg. 0 1 0 1 0 1 1 1 0 0 Config Reg. 1 0 0 0 0 0 0 0 1 0 Register Name Condition OEH = OEL = 2 ms, ALRTIND = 1, Input Channel (LCX) = Enabled Output Data Type = Demodulated Output, Input Tuning Capacitor Value = 1 pF Config Reg. 2 0 0 0 0 0 0 0 0 1 RSSI Pull-Down MOSFET = Off, Config Reg. 3 0 0 0 0 0 0 0 0 1 Recommended Config Reg. 4 0 0 0 0 0 0 0 0 1 Input Channel Sensitivity Reduction = None Config Reg. 5 0 1 0 0 0 0 0 0 0 AGCSIG = 1, Min Modulation Depth = 33% Calculated Column Parity Register 6 0 0 0 1 0 0 0 0 0 Calculated Column Odd Parity Bits CLKDIV = 0 Note 1: 2: The values in the colored area are strongly recommended for the best result. See the calculated row and column parity bits. These bits must be programmed by the user. See Note in Section 5.30.3 "Read/Write Commands for Configuration Registers" for the parity bits. 2012 Microchip Technology Inc. DS22304A-page 57 MCP2035 NOTES: DS22304A-page 58 2012 Microchip Technology Inc. MCP2035 6.0 PACKAGING INFORMATION 6.1 Package Marking Information 14-Lead TSSOP Example XXXXXXXX YYWW NNN 2035I 1217 256 Legend: XX...X Y YY WW NNN e3 * Note: Customer-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week `01') Alphanumeric traceability code Pb-free JEDEC designator for Matte Tin (Sn) This package is Pb-free. The Pb-free JEDEC designator ( e3 ) can be found on the outer packaging for this package. In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. 2012 Microchip Technology Inc. DS22304A-page 59 MCP2035 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS22304A-page 60 2012 Microchip Technology Inc. MCP2035 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 2012 Microchip Technology Inc. DS22304A-page 61 MCP2035 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS22304A-page 62 2012 Microchip Technology Inc. MCP2035 APPENDIX A: REVISION HISTORY Revision A (May 2012) * Original Release of this Document. 2012 Microchip Technology Inc. DS22304A-page 63 MCP2035 NOTES: DS22304A-page 64 2012 Microchip Technology Inc. MCP2035 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. Device X /XX Temperature Range Package Device: MCP2035: Single-Channel Stand-Alone Analog Front-end (AFE) Temperature Range: I Package: ST = Examples: a) MCP2035-I/ST: b) MCP2035T-I/ST: Industrial Temperature, 14LD TSSOP Package Tape and Reel, Industrial Temperature, 14LD TSSOP Package -40C to +85C (Industrial) = 2012 Microchip Technology Inc. Plastic Shrink Small outline (4.4 mm) (TSSOP) DS20000A-page 65 MCP2035 NOTES: DS20000A-page 66 2012 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: * Microchip products meet the specification contained in their particular Microchip Data Sheet. * Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. * There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip's Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. * Microchip is willing to work with the customer who is concerned about the integrity of their code. * Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as "unbreakable." Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip's code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer's risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, PIC32 logo, rfPIC and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MXDEV, MXLAB, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE, rfLAB, Select Mode, Total Endurance, TSHARC, UniWinDriver, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. (c) 2012, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. ISBN: 978-1-62076-2-684 QUALITY MANAGEMENT SYSTEM CERTIFIED BY DNV == ISO/TS 16949 == 2012 Microchip Technology Inc. Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company's quality system processes and procedures are for its PIC(R) MCUs and dsPIC(R) DSCs, KEELOQ(R) code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001:2000 certified. DS22304A-page 67 Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4123 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Japan - Osaka Tel: 81-66-152-7160 Fax: 81-66-152-9310 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8569-7000 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 China - Chongqing Tel: 86-23-8980-9588 Fax: 86-23-8980-9500 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 China - Hangzhou Tel: 86-571-2819-3187 Fax: 86-571-2819-3189 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Hong Kong SAR Tel: 852-2401-1200 Fax: 852-2401-3431 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Taiwan - Hsin Chu Tel: 886-3-5778-366 Fax: 886-3-5770-955 China - Shenzhen Tel: 86-755-8203-2660 Fax: 86-755-8203-1760 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-330-9305 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 DS22304A-page 68 Japan - Yokohama Tel: 81-45-471- 6166 Fax: 81-45-471-6122 11/29/11 2012 Microchip Technology Inc.