SCD8601 Rev T
DESCRIPTION
The Aeroflex Plainview VGR8601/02 consists of a positive (RH117) and a negative (RH137) voltage regulator each
capable of supplying in excess of 1.5Amps over the output voltage range as defined under recommended operating
conditions. Each regulator is exceptionally easy to set-up, requiring only 2 ext ernal resistors to set the output vo ltage .
The module design has been optimized for excellent regulation and low thermal transients. There is full electrical
isolation between positive and negative regulators and each regulator to the package.
Further, the VRG8601/ 0 2 features internal current limiting, thermal shutdown and safe-area compensation, making
them virtually blowout-proof against overloads. The VRG8601 /02 serves a wide variety of applications including
local on-card regulation, programmab le output voltage regulation or precision current regulation.
The VRG8601/02 has been specifically designed to meet exposure to radiation environments. The VRG8601 is
configured for a Thru-Hole 6 lead metal power package and the VRG8602 is configured for a Surface Mount 6 lead
metal power package. It is guaranteed operational from -55°C to +125°C. Available screened to MIL-STD-883, the
VRG8601/02 is ideal for demanding military and space applications.
For detailed performance characteristic curves, applications information and typical applications see the
latest Linear Technology Corporation ®data sheets for their RH/LT117 and RH/LT137, which is available
on-line at www.linear.com.
5
VIN
ADJ
VOUT
RH137
4
3
VIN
ADJ
VOUT
RH117
1
FIGURE 1 – BLOCK DIAGRAM / SCHEMATIC
2 6
Positive
Regulator Regulator
Negative
VRG8601/02
Radiation Tolerant
September 9, 2011
www.aeroflex.com/voltreg
Standard Products
Dual Adjustable Positive/Negative Voltage Regulators
FEATURES
❑Manufactured using Linear Technology Corporation ® Space Qualified RH117 and RH137 die
❑Radiation performance
- Total dose: 100 krads(Si),
Dose rate = 50 - 300 rads(Si)/s
- ELDRS: 50 krads(Si),
Dose rate < 10 mrads(Si)/s
❑Two-Independent voltage regulators
❑Thermal shutdown
❑1.5A output current
❑Adjustable Output Voltage s
❑Packaging – Hermetic metal
– Thru-hole or Surface mount
– 6 Leads, .655"L x .415"W x .200"Ht
– Power package
– Weight - 5 gm max
❑Positive regulator features (RH117)
– Output voltage adjustable: +1.25V to 37V
– 3-Terminal
– Voltage reference: 1.25V
– Load regulation: 1.9% max
– Line regulation: 0.06% max
– Ripple rejection: >66dB
❑Negative regulator featu res (RH 137)
– Output voltage adjustable: -1.25V to -27V
– 3-Terminal
– Voltage reference: 1.25V
– Load regulation: 1.0% typ
– Line regulation: .05% typ
– Ripple rejection: >66dB
❑Designed for aerospace and high reliability space applications
❑Aeroflex Plainview’s Radiation Hardness Assurance Plan is DLA Certified to MIL-PRF-38534, Appendix G.
2
SCD8601 Rev T 9/9/11 Aeroflex Plainview
ABSOLUTE MAXIMUM RATINGS
PARAMETER RANGE UNITS
Operating (Junction) Temperature Range -55 to +150 C
Lead Temperature (soldering, 10 sec) 300 °C
Storage Temperature Range -65 to +150 C
Input-Output Voltage Differential 40 (Pos) 30 (Neg) V
Thermal Resistance (junction to case JC) each, Pos. & Neg. 5°C/W
ESD Rating 1.999 1/ KV
1/ Meets ESD testing per MIL-STD-883, method 3015, Class 1C.
NOTICE: Stresses above those listed under "Absolute Maximums Rating" may cause permanent damage to the device. These are stress rating
only; functional operation beyond the "Operation Conditions" is not recommended and extended exposure beyond the "Operation
Conditions" may effect device reliability. .
RECOMMENDED OPERATING CONDITIONS
PARAMETER RANGE UNITS
Output Voltage Range
Positive Voltage Regulator 1.3 to 37 VDC
Negative Voltage Regulator -1.3 to -27 VDC
Case Operating Temperature Range -55 to +125 °C
POSITIVE REGULATOR – ELECTRICAL PERFORMANCE CHARACTERISTICS 1/
PARAMETER SYM CONDITIONS (P PMAXMIN MAX UNITS
Reference Voltage 4/VREF 3V < (VIN - VOUT) < VDIFF MAX, 10mA < IOUT < IMAX 1.20 1.30 V
Line Regulation 2/ 4/3V < (VIN - VOUT) < VDIFF MAX, IOUT = 10mA - 0.03 %/V
Load Regulation 2/ 4/10mA < IOUT < IMAX, VOUT < 5V
10mA < IOUT < IMAX, VOUT > 5V -
-60
1.2 mV
%
Thermal Regulation IOUT = 1.5A, (VIN - VOUT) = 13.3V, 20ms Pulse, 20W,
TC = +25°C -0.07%/W
Ripple Rejection Ratio VOUT = 10V, f = 120Hz, CADJ = 10µF 66 - dB
Adjustment Pin Current 4/IADJ IOUT = 10mA, 3V < (VIN - VOUT) < 40V - 100 µA
Adjustment Pin Current
Change 4/IADJ 10mA < IOUT < IMAX
3V < (VIN - VOUT) < 40V -5µA
Minimum Load Current 3/ 4/IMIN (VIN - VOUT) = 40V - 5 mA
Current Limit 4/ 5/IMAX (VIN - VOUT) < 15V 1.5 - A
(VIN - VOUT) = 40V, TC = +25°C 0.30 -
Long Term Stability 3/TC = +125°C - 1 %
Thermal Resistance, each
Regulator
(Junction to Case) 3/JC -5°C/W
VOUT
VIN
VOUT
IOUT
VOUT
TIME
3
SCD8601 Rev T 9/9/11 Aeroflex Plainview
NEGATIVE REGULATOR – ELECTRICAL PERFORMANCE CHARACTERISTICS 1/
PARAMETER SYM CONDITIONS MIN MAX UNITS
Reference Voltage 4/VREF 3V < (VIN - VOUT) < VDIFF MAX,10mA < IOUT < IMAX -1.200 -1.300 V
Line Regulation 2/ 4/3V < (VIN - VOUT) < 30V, - 0.05 %/V
Load Regulation 2/ 4/10mA < IOUT < IMAX, VOUT < 5V - 50 mV
10mA < IOUT < IMAX, VOUT > 5V - 1.0 %
Thermal Regulation IOUT = 1.5A, (VIN - VOUT) = 13.3V, 20ms Pu lse, 20W,
TC = +25°C -0.02%/W
Ripple Rejection VOUT = -10V, f = 120Hz, CADJ = 10µF 66 - dB
Adjustment Pin Current 4/IADJ IOUT = 10mA, 3V < (VIN - VOUT) < 30V - 100 µA
Adjustment Pin Current
Change 4/IADJ 10mA < IOUT < IMAX
3V < (VIN - VOUT) < 30V -5µA
Minimum Load Curren t 3/ 4/IMIN (VIN - VOUT) = 30V - 5 mA
(VIN - VOUT) < 10V - 3
Current Limit 4/ 5/IMAX (VIN - VOUT) < 15V 1.5 - A
(VIN - VOUT) = 30V, TC = +25°C 0.24 -
Long Term Stability 3/TC = +125°C - 1 %
Thermal Resistance, each
Regulator
(Junction to Case) 3/JC -5°C/W
Notes:
1/ Unless otherwise specified, these specifications apply for (Vin - Vout) = 5V, Iout = 0.5A and -55°C < Tc < +125°C.
2/ Regulation is measured at a constant junction temperature, using pulse testing with a low duty cycle. Changes in output voltage due to
heating effects are covered under the specification fo r thermal regulat ion. Measurements taken at the output lead must be ad justed for lead
resistance.
3/ Not tested. Shall be guaranteed to th e specified limits.
4/ Specification derated to reflect High Dose Rate (1019 condition A) to 100 krad(Si) and Low Dose Rate (1019 condition D) to 50 krad( Si),
@ +25°C.
5/ Pulsed @ < 10% duty cycle @ +25°C.
VOUT
VIN
VOUT
IOUT
VOUT
TIME
4
SCD8601 Rev T 9/9/11 Aeroflex Plainview
FIGURE 2 – MAXIMUM POWER vs CASE TEMPERATURE
The maximum Power dissipation is limited by the thermal shutdown function of each regulator chip in the VRG8601/02. The
graph above represents the achievable power before the chip shuts down. The first line in the graph represents the maximum
power dissipation of the VRG8601/02 with one regulator on (the other off) and the other line represents both regulators on
dissipating equal power. If both regulators are on and one regulator is dissipating more power that the other, the maximum power
dissipation of the VRG8601/02 will fall between the two lines. This graph is based on the maximum junction temperature of
150°C and a thermal resistance (JC) of 5°C/W.
60
50
40
30
20
10
0 20 40 60 80 100 120 140
Case Temperature (°C)
1 Regulator
0
Both Regulators
Maximum Power
Dissipation
(Watts)
IADJ = 50µAVREF = 1.25V,
+Reg = VOUT = VREF (1+R2/R1) + (IADJ x R2)
-Reg = VOUT = -VREF (1+R2/R1) + (-IADJ x R2)
VRG8601/02
VIN VOUT
ADJ
R1
R2
VREF
Adjustable Regulator
FIGURE 3 – TYPICAL APPLICATIONS
5
SCD8601 Rev T 9/9/11 Aeroflex Plainview
.108
.200
.100
.123
ø.145 THRU
.415
.2075
R.065 TYP.
4 PLCS .655
.415 SQ
±.003
.220 MAX.
±.005
.040
±.002
.030 DIA.
.150 REF. 2° MAX. TYP.
±.020
.720
MEASURED
LEAD TIP
IDENT
ESD/PIN 1
–B–
–A–
–C–
ø.010 B C A
M
ø.010 C B A
FIGURE 4 – PACKAGE OUTLINE — THRU-HOLE POWER PACKAGE
3
456
21
PIN NUMBERS vs FUNCTION
PIN FUNCTION
1POS_ADJ_1
2POS_V
OUT_1
3POS_V
IN_1
4 NEG_ADJ_2
5NEG_V
IN_2
6NEG_V
OUT_2
2x .028
M
ø.010 C B A
.230 MIN
Notes:
1. Dimension Tolerance: ±.005 inches
2. Package contains BeO substrate
3. Case electrically isolated
.122
MAX.
6
SCD8601 Rev T 9/9/11 Aeroflex Plainview
.108
.200
.100
.123
ø.145 THRU
.415
.2075
R.065 TYP.
4 PLCS .655
.415 SQ
±.003
.220 MAX.
±.005
.040 ±.002
.030 DIA.
.122
.150 REF.
±.020.886
IDENT
ESD/PIN 1
–B–
–A–
–C–
ø.010 B C A
M
ø.010 C B A
Notes:
FIGURE 5 – PACKAGE OUTLINE — SURFACE MOUNT POWER PACKAGE
1. Dimension Tolerance: ±.005 inches
2. Package contains BeO substrate
3
456
21
PIN NUMBERS vs FUNCTION
PIN FUNCTION
1POS_ADJ_1
2POS_V
OUT_1
3POS_V
IN_1
4 NEG_ADJ_2
5NEG_V
IN_2
6NEG_V
OUT_2
2x .028
M
ø.010 C B A
.020
.060
3. Case electrically isolated
MAX.
77
SCD8601 Rev T 9/9/11
PLAINVIEW, NEW YORK
Toll Free: 800-THE-1553
Fax: 516-694-6715
SE AND MID-ATLANTIC
Tel: 321-951-4164
Fax: 321-951-4254
INTERNATIONAL
Tel: 805-778-9229
Fax: 805-778-1980
WEST COAST
Tel: 949-362-2260
Fax: 949-362-2266
NORTHEAST
Tel: 603-888-3975
Fax: 603-888-4585
CENTRAL
Tel: 719-594-8017
Fax: 719-594-8468
www.aeroflex.com info-ams@aeroflex.com
Aeroflex Microelectronic Solutions reserves the right to
change at any time without notice the specifications, design,
function, or form of its products described herein. All
parameters must be validated for each customer's application
by engineering. No liab ility is assumed as a result of use of
this product. No patent licenses are implied.
EXPORT CONTROL: EXPOR T WARNING:
This product is controlled for export under the International Traffic in
Arms Regulations (ITAR). A license from the U.S. Department of
State is required prior to the export of this product from the United
States.
Aeroflex’s military and space products are controlled for export under
the International Traffic in Arms Regulations (ITAR) and may not be
sold or proposed or offered for sale to certain countries. (See ITAR
126.1 for complete information.)
Our passion for performance is defined by three
attributes represented by these three icons:
solution-minded, perform a nce -driven and cu stom e r-foc use d
and the Linear Technology logo are registered trademarks and RH117 & R H1 37 a re a cop yright of Linear Tec hno logy Co rpo ration.
ORDERING INFORMATION
MODEL DLA SMD # SCREENING PACKAGE
VRG8601-7 - Commercial Flow, +25°C testing only
6 Lead
Thru-Hole
Power Pkg
VRG8601-S - Milit ary Temperature, -55°C to +125°C
Screened in accordance with the individual Test Methods
of MIL-STD-883 for Space Applications
VRG8601-201-1S 5962-0521901KXC In accordance with DLA SMD
VRG8601-201-2S 5962-0521901KXA
VRG8601-901-1S 5962R0521901KXC In accordance with DLA Certified RHA Program Plan
to RHA level "R", 100 krads(Si)
VRG8601-901-2S 5962R0521901KXA
VRG8602-7 - Commercial Flow, +25°C testing only
6 Lead
Surface Mount
Power Pkg
VRG8602-S - Milit ary Temperature, -55°C to +125°C
Screened in accordance with the individual Test Methods
of MIL-STD-883 for Space Applications
VRG8602-201-1S 5962-0521901KYC In accordance with DLA SMD
VRG8602-201-2S 5962-0521901KYA
VRG8602-901-1S 5962R0521901KYC In accordance with DLA Certified RHA Program Plan
to RHA level "R", 100 krads(Si)
VRG8602-901-2S 5962R0521901KYA
