EVALUATION KIT AVAILABLE MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter General Description The MAX7060 frequency and power-programmable ASK/FSK transmitter operates at 280MHz to 450MHz frequencies. This device incorporates a fully integrated fractional-N synthesizer, which allows the user to set the RF operating frequency to a large fraction of the 280MHz to 450MHz frequency range with a single crystal. For example, the MAX7060 can be tuned from 285MHz to 420MHz with a 15MHz crystal. The RF output power is user-controlled between +14dBm and -14dBm, with a 5V supply or with battery voltages as low as 3.2V. At the minimum specified battery voltage of 2.1V, the RF output power-control range is between +10dBm and -14dBm. To maintain a good output power match across a broad range of frequencies, the MAX7060 also contains a programmable matching capacitor connected in parallel with the power amplifier (PA) output. ASK modulation is accomplished by switching the PA on and off, so excellent modulation (on/off) ratios are achieved. ASK amplitude shaping is available to reduce the width of the transmission spectrum. FSK modulation is accomplished by changing the coefficients of the high-resolution fractional-N synthesizer, so FSK deviation is extremely accurate. Data rates up to 50kbps Manchester coded for ASK and 70kbps Manchester coded for FSK can be maintained while still satisfying regulatory emission-bandwidth standards. The full set of configuration functions are handled by an on-chip serial peripheral interface (SPI). There is also a manual mode where a limited number of settings can be made directly through selected pins. The startup time is very short, and data can be transmitted 250Fs after the enable command. The MAX7060 operates from a 2.1V to 3.6V supply, or internal regulators can be used for supply voltages between 4.5V and 5.5V. The standby current in the 3V mode is 400nA at room temperature, and can be reduced to 5nA using the low-power shutdown (LSHDN) pin. The MAX7060 is available in a 24-pin (4mm x 4mm) thin QFN package and is specified for the automotive temperature range from -40NC to +125NC. Features S Fully Integrated, Fast Fractional-N PLL 280MHz to 450MHz RF Frequency Frequency Range 100% Tested at +125NC < 250s Startup Time Adjustable FSK Mark and Space Frequencies Ultra-Clean FSK Modulation 50kbps Manchester Data Rate ASK 70kbps Manchester Data Rate FSK S Programmable Power Amplifier +14dBm Tx Power with 5V Supply +10dBm Tx Power at 2.1V Supply 28dB Power-Control Range in 1dB Steps S Tunable PA Matching Capacitor S Control Through SPI or Manual Settings S Low Shutdown Current for 2.1V to 3.6V Supply 400nA Standby Current, Power-On-Reset (POR) Active 5nA Shutdown Current, POR Inactive S Supply Flexibility 2.1V to 3.6V Single-Supply Operation or 4.5V to 5.5V Supply Operation with Internal Regulators S 24-Pin (4mm x 4mm) TQFN Package S FCC Part 15, ETSI EN 300 220 Compliant* *ETSI compliance up to +6dBm EIRP. Applications Garage-Door Openers Remote Controls Home and Industrial Automation Sensor Networks Security Systems Ordering Information PART TEMP RANGE PIN-PACKAGE MAX7060ATG+ -40NC to +125NC 24 TQFN-EP* MAX7060ATG/V+ -40NC to +125NC 24 TQFN-EP* +Denotes a lead(Pb)-free/RoHS-compliant package. /V denotes an automotive qualified part. *EP = Exposed pad. For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim's website at www.maximintegrated.com. 19-5096; Rev 1; 3/12 MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter ABSOLUTE MAXIMUM RATINGS GPOVDD, VDD5 to GND.......................................-0.3V to +6.0V DVDD, PAVDD, and AVDD to GND......................-0.3V to +4.0V ENABLE, SCLK_PWR0, SDI_PWR1, DIN, CS_DEV, LSHDN, FREQ0, FREQ1, FREQ2, GPO1, and GPO2_MOD to GND......................-0.3V to (VDD5 + 0.3V) PAOUT, ROUT, and PAVOUT to GND ....................... -0.3V to (VPAVDD + 0.3V) XTAL1 and XTAL2 to GND.................... -0.3V to (VAVDD + 0.3V) Continuous Power Dissipation (TA = +70NC) 24-Pin Thin QFN (derate 20.8mW/NC above +70NC)..........................1666.7mW Operating Temperature Range......................... -40NC to +125NC Storage Temperature Range............................. -60NC to +150NC Lead Temperature (soldering, 10s) ................................+300NC Soldering Temperature (reflow).......................................+260NC Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. DC ELECTRICAL CHARACTERISTICS (5V OPERATION) (Typical Application Circuit, 50I system impedance, tuned for 315MHz to 434MHz operation. VDD5 = VGPOVDD = 4.5V to 5.5V, fRF = 280MHz to 450MHz, fXTAL = 15MHz to 16MHz, TA = -40NC to +125NC, unless otherwise noted. Typical values are at VDD5 = VGPOVDD = +5V, TA = +25NC, PA matched for optimum output power, unless otherwise noted. All min and max values are 100% tested at TA = +125NC and guaranteed by design and characterization over temperature, unless otherwise noted.) PARAMETER Supply Voltage Regulated Analog Supply Voltage SYMBOL CONDITIONS VDD MAX UNITS 5 5.5 V 3.2 PLL on, PA on, data at 50% duty cycle (ASK), +10dBm (PApwr = 0x19) output power (Notes 1, 2) IDD PLL on, PA on, data at 100% duty cycle, +10dBm (PApwr = 0x19) output power (Note 1) PLL on, PA on, data at 100% duty cycle, max (PApwr = 0x1E) output power (Note 1) Standby Current TYP 4.5 AVDD PLL on, PA off Active Supply Current MIN ISTDBY VENABLE < VIL, VLSHDN < VIL V fRF = 315MHz 4.7 6.0 fRF = 433.92MHz 5.3 6.9 fRF = 315MHz 12.5 fRF = 433.92MHz 14.2 fRF = 315MHz 19 26 fRF = 433.92MHz 25 31.6 fRF = 315MHz 28 fRF = 433.92MHz 34 TA = +25NC 1.1 TA = +85NC 1.3 TA = +125NC 3.8 mA FA 6.1 DIGITAL I/O Input High Threshold VIH Input Low Threshold VIL 2 0.9 x VDVDD V 0.1 x VDVDD V Maxim Integrated MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter DC ELECTRICAL CHARACTERISTICS (5V OPERATION) (continued) (Typical Application Circuit, 50I system impedance, tuned for 315MHz to 434MHz operation. VDD5 = VGPOVDD = 4.5V to 5.5V, fRF = 280MHz to 450MHz, fXTAL = 15MHz to 16MHz, TA = -40NC to +125NC, unless otherwise noted. Typical values are at VDD5 = VGPOVDD = +5V, TA = +25NC, PA matched for optimum output power, unless otherwise noted. All min and max values are 100% tested at TA = +125NC and guaranteed by design and characterization over temperature, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS Input Pulldown Sink Current IIH 6 FA Input Pullup Source Current IIL 5 FA Output-Voltage High Output-Voltage Low VOH VOL ISINK = 100FA (GPO1 and GPO2_MOD, gp1bst bit = 0) VGPOVDD - 0.10 ISINK = 200FA (GPO1), boost = on (gp1bst bit = 1) VGPOVDD - 0.14 ISOURCE = 100FA (GPO1 and GPO2_MOD, gp1bst bit = 0) 0.10 ISOURCE = 200FA (GPO1), boost = on (gp1bst bit = 1) 0.14 V V DC ELECTRICAL CHARACTERISTICS (3V OPERATION) (Typical Application Circuit, 50I system impedance, tuned for 315MHz to 434MHz operation. VDD5 = VGPOVDD = VAVDD = VDVDD = VPAVDD = 2.1V to 3.6V, fRF = 280MHz to 450MHz, fXTAL = 15MHz to 16MHz, TA = -40NC to +125NC, unless otherwise noted. Typical values are at VDD5 = VGPOVDD = VAVDD = VDVDD = VPAVDD = 2.7V, TA = +25NC, PA matched for optimum output power, unless otherwise noted. All min and max values are 100% tested at TA = +125NC and guaranteed by design and characterization over temperature, unless otherwise noted.) PARAMETER Supply Voltage SYMBOL CONDITIONS PLL on, PA off Active Supply Current MIN TYP MAX UNITS 2.1 2.7 3.6 V fRF = 315MHz 4.2 6.2 fRF = 433.92MHz 4.8 7.2 VDD IDD PLL on, PA on, data fRF = 315MHz at 50% duty cycle (ASK), +10dBm (PApwr = 0x19) output power fRF = 433.92MHz (Notes 1, 2) PLL on, PA on, data at 100% duty cycle, fRF = 315MHz +10dBm (PApwr = 0x19) output power f = 433.92MHz RF (Note 1) Standby Current Shutdown Current Maxim Integrated ISTDBY ISHDN VENABLE < VIL, VLSHDN < VIL VENABLE < VIL, VLSHDN > VIH 11 mA 13 17.2 27 22 31.6 TA = +25NC 0.4 TA = +85NC 0.5 TA = +125NC 2.5 TA = +25NC 0.005 TA = +85NC 0.3 TA = +125NC 2.6 FA 6.0 FA 6.0 3 MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter DC ELECTRICAL CHARACTERISTICS (3V OPERATION) (continued) (Typical Application Circuit, 50I system impedance, tuned for 315MHz to 434MHz operation. VDD5 = VGPOVDD = VAVDD = VDVDD = VPAVDD = 2.1V to 3.6V, fRF = 280MHz to 450MHz, fXTAL = 15MHz to 16MHz, TA = -40NC to +125NC, unless otherwise noted. Typical values are at VDD5 = VGPOVDD = VAVDD = VDVDD = VPAVDD = 2.7V, TA = +25NC, PA matched for optimum output power, unless otherwise noted. All min and max values are 100% tested at TA = +125NC and guaranteed by design and characterization over temperature, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS DIGITAL I/O 0.9 x VDVDD V Input High Threshold VIH Input Low Threshold VIL Input Pulldown Sink Current IIH 5 FA Input Pullup Source Current IIL 1.3 FA Output-Voltage High Output-Voltage Low VOH VOL 0.1 x VDVDD ISINK = 100FA (GPO1 and GPO2_MOD, gp1bst bit = 0) VGPOVDD - 0.10 ISINK = 200FA (GPO1), boost = on (gp1bst bit = 1) VGPOVDD - 0.14 ISOURCE = 100FA (GPO1 and GPO2_MOD, gp1bst bit = 0) 0.10 ISOURCE = 200FA (GPO1), boost = on (gp1bst bit = 1) 0.14 V V V AC ELECTRICAL CHARACTERISTICS (5V OPERATION) (Typical Application Circuit, 50I system impedance, tuned for 315MHz to 434MHz operation, VDD5 = VGPOVDD = 4.5V to 5.5V, fRF = 280MHz to 450MHz, fXTAL = 15MHz to 16MHz, TA = -40NC to +125NC, unless otherwise noted. Typical values are at VDD5 = VGPOVDD = +5V, TA = +25NC, PA matched for optimum output power, unless otherwise noted. All min and max values are 100% tested at TA = +125NC and guaranteed by design and characterization over temperature, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS 450 MHz GENERAL CHARACTERISTICS Frequency Range Power-On Time Maximum Data Rate (PApwr = 0x1E) 4 280 tON ENABLE low-to-high transition, frequency settled to within 50kHz of the desired carrier (includes time for VPAVOUT to settle) 130 ENABLE low-to-high transition, frequency settled to within 5kHz of the desired carrier (includes time for VPAVOUT to settle) 185 ASK mode (no shaping) FSK mode Fs Manchester encoded 50 Nonreturn to zero 100 Manchester encoded 70 Nonreturn to zero 140 kbps Maxim Integrated MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter AC ELECTRICAL CHARACTERISTICS (5V OPERATION) (continued) (Typical Application Circuit, 50I system impedance, tuned for 315MHz to 434MHz operation, VDD5 = VGPOVDD = 4.5V to 5.5V, fRF = 280MHz to 450MHz, fXTAL = 15MHz to 16MHz, TA = -40NC to +125NC, unless otherwise noted. Typical values are at VDD5 = VGPOVDD = +5V, TA = +25NC, PA matched for optimum output power, unless otherwise noted. All min and max values are 100% tested at TA = +125NC and guaranteed by design and characterization over temperature, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MIN Time from end of SPI write or change of FREQ0, FREQ1, or FREQ2 pins, to frequency settled to within 5kHz of desired carrier Carrier-Frequency Switching Time TYP MAX UNITS 60 Fs 340 MHz/V PLL VCO Gain KVCO fRF = 315MHz PLL Phase Noise fRF = 433.92MHz 10kHz offset -78 1MHz offset -97 10kHz offset -74 1MHz offset dBc/Hz -97 Loop Bandwidth 300 Reference Frequency Input Level kHz 500 mVP-P Frequency Divider Range 19 28 Frequency Deviation (FSK) Q2 Q100 kHz CRYSTAL OSCILLATOR Crystal Frequency fXTAL Crystal Load Capacitance (Note 3) 15 to 16 MHz 10 pF POWER AMPLIFIER Output Transmit Power (Note 1) Power-Control Step Size POUT Maximum output transmit power: PApwr = 0x1E +14.5 Minimum output transmit power: PApwr = 0x00 -14 dBm 0.95 dB Modulation Depth (Note 1) 70 dB Maximum Carrier Harmonics (Note 1) -24 dBc -42 dBc 0 to 7.75 pF Reference Spur PAOUT Capacitor Tuning Range Maxim Integrated 5 MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter AC ELECTRICAL CHARACTERISTICS (3V OPERATION) (Typical Application Circuit, 50I system impedance, tuned for 315MHz to 434MHz operation. VDD5 = VGPOVDD = VAVDD = VDVDD = VPAVDD = 2.1V to 3.6V, fRF = 280MHz to 450MHz, fXTAL = 15MHz to 16MHz, TA = -40NC to +125NC, unless otherwise noted. Typical values are at VDD5 = VGPOVDD = VAVDD = VDVDD = VPAVDD = 2.7V, TA = +25NC, PA matched for optimum output power, unless otherwise noted. All min and max values are 100% tested at TA = +125NC and guaranteed by design and characterization over temperature, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS 450 MHz GENERAL CHARACTERISTICS Frequency Range Power-On Time 280 tON ENABLE low-to-high transition, frequency settled to within 50kHz of the desired carrier (includes time for VPAVOUT to settle) 120 ENABLE low-to-high transition, frequency settled to within 5kHz of the desired carrier (includes time for VPAVOUT to settle) 200 ASK mode (no shaping) Maximum Data Rate (PApwr = 0x19) FSK mode Fs Manchester encoded 50 Nonreturn to zero 100 Manchester encoded 70 Nonreturn to zero 140 Time from end of SPI write or change of FREQ0, FREQ1, or FREQ2 pins, to frequency settled to within 5kHz of desired carrier Carrier-Frequency Switching Time kbps 60 Fs 340 MHz/V PLL VCO Gain KVCO fRF = 315MHz PLL Phase Noise fRF = 433.92MHz 10kHz offset -78 1MHz offset -97 10kHz offset -74 1MHz offset -97 dBc/Hz Loop Bandwidth 300 kHz Reference Frequency Input Level 500 mVP-P Frequency Divider Range 19 28 CRYSTAL OSCILLATOR Frequency Deviation (FSK) Q2 Q100 kHz 15 to 16 MHz Frequency Pulling by Power Supply 4 ppm/V Crystal Load Capacitance (Note 3) 10 pF Crystal Frequency fXTAL POWER AMPLIFIER VPAVDD = 2.1V, PApwr = 0x1E Output Transmit Power (Note 1) Power-Control Step Size Modulation Depth (Note 1) 6 POUT +10 VPAVDD = 3.6V, PApwr = 0x1E +15 PApwr = 0x00 -14.5 dBm 0.95 dB 70 dB Maxim Integrated MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter AC ELECTRICAL CHARACTERISTICS (3V OPERATION) (continued) (Typical Application Circuit, 50I system impedance, tuned for 315MHz to 434MHz operation. VDD5 = VGPOVDD = VAVDD = VDVDD = VPAVDD = 2.1V to 3.6V, fRF = 280MHz to 450MHz, fXTAL = 15MHz to 16MHz, TA = -40NC to +125NC, unless otherwise noted. Typical values are at VDD5 = VGPOVDD = VAVDD = VDVDD = VPAVDD = 2.7V, TA = +25NC, PA matched for optimum output power, unless otherwise noted. All min and max values are 100% tested at TA = +125NC and guaranteed by design and characterization over temperature, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MIN TYP Maximum Carrier Harmonics (Note 1) UNITS -24 dBc -43 dBc 0 to 7.75 pF Reference Spur PAOUT Capacitor Tuning Range MAX SERIAL PERIPHERAL INTERFACE (SPI) TIMING CHARACTERISTICS (SPI timing characteristics are valid for both 3V and 5V modes. SPI timing is production tested at worst-case temperature and supply with a clock frequency of 3MHz.) PARAMETER SYMBOL Minimum SCLK_PWR0 Low to Falling-Edge of CS_DEV Setup Time CONDITIONS MIN TYP MAX UNITS tSC 30 ns Minimum CS_DEV Low to Rising Edge of SCLK_PWR0 Setup Time tCSS 15 ns Minimum SCLK_PWR0 Low to Rising Edge of CS_DEV Setup Time tHCS 60 ns Minimum SCLK_PWR0 Low After Rising Edge of CS_DEV Hold Time tHS 15 ns Minimum Data Valid to SCLK_ PWR0 Rising-Edge Setup Time tDS 30 ns Minimum Data Valid to SCLK_ PWR0 Rising-Edge Hold Time tDH 15 ns Minimum SCLK_PWR0 High Pulse Width tCH 120 ns Minimum SCLK_PWR0 Low Pulse Width tCL 120 ns Minimum CS_DEV High Pulse Width tCSH 120 ns Maximum Transition Time from Falling-Edge of CS_DEV to Valid GPO2_MOD tCSG CL = 10pF load capacitance from GPO2_MOD to ground 400 ns Maximum Transition Time from Falling Edge of SCLK_PWR0 to Valid GPO2_MOD tCG CL = 10pF load capacitance from GPO2_MOD to ground 400 ns Note 1: Supply current and output power are greatly dependent on board layout and PAOUT match. Note 2: 50% duty cycle at 10kHz ASK data (Manchester coded). Note 3: Dependent on PCB trace capacitance. Maxim Integrated 7 MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter CS_DEV tCSH tSC tHCS tCSS SCLK_PWRO tDS tCH tCL tDH tHS SDI_PWR1 tCG tCSG GPO2_MOD Figure 1. SPI Timing Diagram Typical Operating Characteristics (Typical Application Circuit, 50I system impedance, VDD5 = VGPOVDD = VAVDD = VDVDD = VPAVDD = 2.1V to 3.6V, fRF = 280MHz to 450MHz, fXTAL = 16MHz, TA = -40NC to +125NC, unless otherwise noted. Typical values are at VDD5 = VGPOVDD = VAVDD = VDVDD = VPAVDD = 2.7V, TA = +25NC, PA matched for optimum output power, unless otherwise noted. Supply current and output power are greatly dependent on board layout and PAOUT match.) SUPPLY CURRENT vs. SUPPLY VOLTAGE (fRF = 315MHz, PA ON) TA = -40C 24 TA = +125C PApwr = 0x1E TA = +85C 20 18 +125C 16 PApwr = 0x16 14 TA = +125C 18 +125C PApwr = 0x16 16 2.4 2.7 3.0 3.3 MAX7060 toc03 TA = +85C 5 4 TA = +25C 3 TA = -40C 2 4.5 3.6 TA = +125C 6 -40C 10 2.1 4.7 4.9 5.1 5.3 5.5 2.1 2.4 2.7 3.0 3.3 3.6 VDD5 (V) VDD5 (V) SUPPLY CURRENT vs. SUPPLY VOLTAGE (fRF = 433.92MHz, PA ON) SUPPLY CURRENT vs. SUPPLY VOLTAGE (fRF = 433.92MHz, PA ON) SUPPLY CURRENT vs. SUPPLY VOLTAGE (fRF = 433.92MHz, PA OFF) 3V MODE TA = +25C TA = -40C 30 28 TA = +125C PApwr = 0x1E 36 MAX7060 toc04 38 36 34 32 TA = +85C -40C PApwr = 0x16 PApwr = 0x1E 34 5V MODE 32 30 TA = +85C 28 TA = +25C TA = -40C TA = +125C 26 24 -40C PApwr = 0x16 22 20 +125C 16 14 2.1 2.4 2.7 3.0 VDD5 (V) 3.3 3.6 3V MODE 7 TA = +125C TA = +85C 6 5 4 TA = +25C TA = -40C 3 18 +125C 8 4.5 4.7 4.9 5.1 VDD5 (V) 5.3 MAX7060 toc06 VDD5 (V) SUPPLY CURRENT (mA) SUPPLY CURRENT (mA) 20 12 -40C 10 8 22 TA = +85C TA = +25C 14 12 26 24 22 20 18 16 TA = -40C 24 SUPPLY CURRENT (mA) 22 26 3V MODE 7 MAX7060 toc05 SUPPLY CURRENT (mA) 26 8 MAX7060 toc02 TA = +25C PApwr = 0x1E 5V MODE 28 SUPPLY CURRENT (mA) 3V MODE 28 30 MAX7060 toc01 30 SUPPLY CURRENT vs. SUPPLY VOLTAGE (fRF = 315MHz, PA OFF) SUPPLY CURRENT (mA) SUPPLY CURRENT vs. SUPPLY VOLTAGE (fRF = 315MHz, PA ON) 2 5.5 2.1 2.4 2.7 3.0 3.3 3.6 VDD5 (V) Maxim Integrated MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter Typical Operating Characteristics (continued) (Typical Application Circuit, 50I system impedance, VDD5 = VGPOVDD = VAVDD = VDVDD = VPAVDD = 2.1V to 3.6V, fRF = 280MHz to 450MHz, fXTAL = 16MHz, TA = -40NC to +125NC, unless otherwise noted. Typical values are at VDD5 = VGPOVDD = VAVDD = VDVDD = VPAVDD = 2.7V, TA = +25NC, PA matched for optimum output power, unless otherwise noted. Supply current and output power are greatly dependent on board layout and PAOUT match.) OUTPUT POWER vs. SUPPLY VOLTAGE (fRF = 315MHz, PA ON) PApwr = 0x1E TA = +125C TA = +25C TA = +85C TA = -40C PApwr = 0x16 8 16 3V MODE 14 TA = +125C TA = +25C 11 TA = +85C PApwr = 0x16 TA = +25C TA = +125C TA = +125C 2.1 2.4 2.7 3.0 3.3 10 TA = +125C TA = -40C TA = +25C 8 6 4 TA = -40C 5 3.6 TA = +25C TA = +85C TA = -40C PApwr = 0x1E 12 7 4 4.5 4.7 PApwr = 0x16 2 4.9 5.1 5.3 5.5 2.1 2.4 TA = +85C 2.7 TA = +125C 3.0 3.3 3.6 VDD5 (V) VDD5 (V) VDD5 (V) OUTPUT POWER vs. SUPPLY VOLTAGE (fRF = 433.92MHz, PA ON) PA POWER vs. PA POWER CODE, 315MHz SUPPLY CURRENT vs. PA POWER CODE, 315MHz 20 13 VDD5 = 3.6V 3V MODE 15 10 TA = +125C TA = +25C 9 POUT (dBm) 11 TA = -40C TA = -40C TA = +85C PApwr = 0x16 VDD5 = 2.7V VDD5 = 2.1V 0 -5 5 3 4.5 4.9 5.1 5.3 0 5 10 15 20 25 30 0 35 5 10 15 20 25 30 PA POWER CODE (DECIMAL) PA POWER vs. PA POWER CODE, 315MHz SUPPLY CURRENT vs. PA POWER CODE, 315MHz PA POWER vs. PA POWER CODE, 433.92MHz 25 -4 VDD5 = 5V VDD5 = 4.5V 20 15 VDD5 = 5.5V Maxim Integrated 35 0 5 10 VDD5 = 3.6V VDD5 = 2.7V 5 VDD5 = 2.1V 0 -5 -15 VDD5 = 5V 5 10 15 20 25 30 PA POWER CODE (DECIMAL) 35 -10 -12 5 3V MODE 15 10 10 -16 20 MAX7060 toc14 5V MODE POUT (dBm) VDD5 = 4.5V VDD5 = 5.5V -8 30 SUPPLY CURRENT (mA) 4 0 VDD5 = 2.1V 10 PA POWER CODE (DECIMAL) 8 0 VDD5 = 2.7V 15 VDD5 (V) 5V MODE 12 20 0 -15 5.5 MAX7060 toc13 16 4.7 VDD5 = 3.6V 25 5 -10 TA = +25C TA = +125C 3V MODE 30 MAX7060 toc15 7 5 35 MAX7060 toc12 5V MODE SUPPLY CURRENT (mA) TA = +85C MAX7060 toc11 PApwr = 0x1E MAX7060 toc10 15 POUT (dBm) 5V MODE TA = -40C 9 6 POUT (dBm) TA = +85C 13 12 10 PApwr = 0x1E 15 POUT (dBm) POUT (dBm) 14 17 MAX7060 toc09 16 TA = +25C T = +85C A TA = -40C POUT (dBm) 3V MODE MAX7060 toc07 18 OUTPUT POWER vs. SUPPLY VOLTAGE (fRF = 433.92MHz, PA ON) MAX7060 toc08 OUTPUT POWER vs. SUPPLY VOLTAGE (fRF = 315MHz, PA ON) 15 20 25 PA POWER CODE (DECIMAL) 30 35 -20 0 5 10 15 20 25 30 PA POWER CODE (DECIMAL) 35 9 MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter Typical Operating Characteristics (continued) (Typical Application Circuit, 50I system impedance, VDD5 = VGPOVDD = VAVDD = VDVDD = VPAVDD = 2.1V to 3.6V, fRF = 280MHz to 450MHz, fXTAL = 16MHz, TA = -40NC to +125NC, unless otherwise noted. Typical values are at VDD5 = VGPOVDD = VAVDD = VDVDD = VPAVDD = 2.7V, TA = +25NC, PA matched for optimum output power, unless otherwise noted. Supply current and output power are greatly dependent on board layout and PAOUT match.) 10 5 VDD5 = 2.7V 25 20 15 VDD5 = 5.5V -5 35 5V MODE VDD5 = 5V 0 0 5 10 15 20 25 30 25 20 VDD5 = 5.5V 15 VDD5 = 5V 10 5 -15 35 VDD5 = 4.5V 30 -10 5 0 5 10 15 20 25 30 0 35 5 10 15 20 25 30 PA POWER CODE (DECIMAL) PA POWER CODE (DECIMAL) PA POWER CODE (DECIMAL) PHASE NOISE vs. OFFSET FREQUENCY (fRF = 315MHz, TA = +25C, VDD = 2.7V, PA CODE = 0x19) PHASE NOISE vs. OFFSET FREQUENCY (fRF = 433.92MHz, TA = +25C, VDD = 2.7V, PA CODE = 0x19) REFERENCE SPUR MAGNITUDE vs. SUPPLY VOLTAGE PHASE NOISE (dBc/Hz) -80 -90 -100 -110 -70 -80 -90 -100 -120 -110 -130 -120 1k 10k 100k 1M OFFSET FREQUENCY (Hz) 10M 433.92MHz 315MHz -44 -46 -48 -130 -140 3V MODE -42 35 MAX7060 toc21 -60 -40 REFERENCE SPUR MAGNITUDE (dBc) -70 MAX7060 toc20 -50 MAX7060 toc19 -60 PHASE NOISE (dBc/Hz) 0 VDD5 = 2.1V 10 10 VDD5 = 4.5V 5V MODE SUPPLY CURRENT (mA) 35 30 15 POUT (dBm) SUPPLY CURRENT (mA) VDD5 = 3.6V MAX7060 toc17 3V MODE MAX7060 toc16 45 40 SUPPLY CURRENT vs. PA POWER CODE, 433.92MHZ PA POWER vs. PA POWER CODE, 433.92MHz MAX7060 toc18 SUPPLY CURRENT vs. PA POWER CODE, 433.92MHZ 1k 10k 100k 1M OFFSET FREQUENCY (Hz) 10M 2.1 2.4 2.7 3.0 3.3 3.6 SUPPLY VOLTAGE (V) Maxim Integrated MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter Typical Operating Characteristics (continued) (Typical Application Circuit, 50I system impedance, VDD5 = VGPOVDD = VAVDD = VDVDD = VPAVDD = 2.1V to 3.6V, fRF = 280MHz to 450MHz, fXTAL = 16MHz, TA = -40NC to +125NC, unless otherwise noted. Typical values are at VDD5 = VGPOVDD = VAVDD = VDVDD = VPAVDD = 2.7V, TA = +25NC, PA matched for optimum output power, unless otherwise noted. Supply current and output power are greatly dependent on board layout and PAOUT match.) FSK SPECTRUM (fRF = 315MHz, +25C, VDD = 2.7V, PA CODE = 0x19 50kHz DEVIATION, 4kHz SQUARE WAVE ON DIN) REFERENCE SPUR MAGNITUDE vs. SUPPLY VOLTAGE POUT (dBm) -44 RBW = 10kHz VBW = 10kHz 10 433.92MHz 315MHz -46 MAX7060 toc23 5V MODE -42 20 MAX7060 toc22 REFERENCE SPUR MAGNITUDE (dBc) -40 0 -10 -20 -48 4.5 4.7 4.9 5.1 5.3 -30 314.5 5.5 314.7 314.9 SUPPLY VOLTAGE (V) 315.1 315.3 315.5 fRF (MHz) XTAL1 XTAL2 AVDD N.C. VDD5 PAVOUT Pin Configuration/Functional Diagram 18 17 16 15 14 13 CRYSTAL OSCILLATOR 20 SCLK_PWR0 21 ENABLE 22 DIN 23 LOOP FILTER PFD VCO Maxim Integrated PA ASK DATA MODULATOR 3 1 2 3 GPO2_MOD GPO1 DVDD 12 ROUT 11 PAVDD 10 PAOUT 9 N.C. 8 LSHDN 7 FREQ2 5 EXPOSED PAD GND MAX7060 24 + PULSE SHAPING PA POWER CONTROL FREQUENCY DIVIDER SERIAL INTERFACE, CONFIGURATION, AND CONTROL /K N.C. VOLTAGE REGULATOR 4 5 6 FREQ1 SDI_PWR1 CHARGE PUMP FREQ0 19 GPOVDD CS_DEV TQFN 11 MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter Pin Description PIN NAME FUNCTION 1 GPO2_MOD (SPI Mode/Manual Mode) Digital Input/Output. GPO2 output in SPI mode. Acts as an SPI data output when CS_DEV is low. ASK (0)/FSK (1) modulation select input in manual mode. This pin is internally pulled down in manual mode. 2 GPO1 General-Purpose Output 1. In SPI mode, this pin can output many internal status signals. In manual mode, this pin outputs the synthesizer lock-detect (lockdet) signal. 3 DVDD Digital-Supply Voltage Input. Bypass to GND with a 0.01FF capacitor as close as possible to the pin. 4 GPOVDD 5 FREQ0 Frequency-Select Pin 0 in Manual Mode. Internally pulled down. FREQ0 = FREQ1 = FREQ2 = 0 for SPI mode. 6 FREQ1 Frequency-Select Pin 1 in Manual Mode. Internally pulled down. FREQ0 = FREQ1 = FREQ2 = 0 for SPI mode. 7 FREQ2 Frequency-Select Pin 2 in Manual Mode. Internally pulled down. FREQ0 = FREQ1 = FREQ2 = 0 for SPI mode. 8 LSHDN Low-Power Shutdown Current-Select Digital Input. Turns off internal POR circuit and disables pullup/pulldown currents. Must be driven low for normal operation in 3V mode. Functional only in 3V mode. Connect to GND in 5V mode. 9, 15, 24 N.C. 10 PAOUT Power Amplifier Output. Requires a pullup inductor to PAVOUT, which can be part of the outputmatching network to an antenna. 11 PAVDD Power Amplifier Predriver Power-Supply Input. Bypass to GND with a 680pF capacitor and a 0.01FF as close as possible to the pin. 12 ROUT 13 PAVOUT 14 VDD5 16 AVDD 17 XTAL2 18 XTAL1 Crystal Input 1. AC-couple to GND if XTAL2 is driven from an AC-coupled external reference. 19 CS_DEV (SPI Mode/Manual Mode) Serial Peripheral Interface (SPI) Active-Low Chip-Select Input. FSK frequency-deviation input (0 = low deviation, 1 = high deviation) in manual mode. Internally pulled up. 20 SDI_PWR1 21 SCLK_PWR0 22 ENABLE 23 DIN Transmit Data Digital Input. Internally pulled down. -- EP Exposed Pad. Solder evenly to the board's ground plane for proper operation. 12 Power-Supply Voltage Input for GPOs and ESD-Protection Devices. Bypass to GND with a 0.01FF capacitor as close as possible to the pin. No Connection. Internally not connected. Leave unconnected. Envelope-Shaping Resistor Connection. See the Typical Application Circuits and the ASK Envelope Shaping sections for details. Power Amplifier Power-Control Output. Controls the transmitted power. Connect to PA pullup inductor. Bypass to ground with 680pF capacitor. Supply Voltage Input. Bypass to ground with 0.01FF and 0.1FF capacitors. Analog Supply Voltage and Regulator Output. Bypass to GND with 0.1FF and 0.01FF capacitors as close as possible to the pin. Crystal Input 2. XTAL2 can be driven from an AC-coupled external reference. (SPI Mode/Manual Mode) SPI Data Input in SPI Mode. Power-control MSB input in manual mode. Internally pulled down. (SPI Mode/Manual Mode) SPI Clock Input in SPI Mode. Power-control LSB input in manual mode. Internally pulled down. Enable Digital Input. All internal circuits (except the PA in ASK mode) are enabled on the rising edge of ENABLE. Internally pulled down. Maxim Integrated MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter Detailed Description The MAX7060 is power and frequency programmable from 280MHz to 450MHz. The MAX7060 has an internal transmit power control that can be programmed over a 28dB power range. The MAX7060 has tuning capacitors at the output of the power amplifier (PA) to ensure highpower efficiency at various programmable frequencies with a single matching network. The crystal-based architecture of the MAX7060 eliminates many of the common problems with SAW transmitters by providing greater modulation depth, faster frequency settling, tighter tolerance of the transmit frequency, and reduced temperature dependence. In particular, the tighter transmit frequency tolerance means that a superheterodyne receiver with a narrower IF bandwidth (therefore lower noise bandwidth) can be used. The payoff is better overall receiver performance when using a superheterodyne receiver such as the MAX1473, MAX1471, MAX7033, MAX7034, MAX7036, and MAX7042. The MAX7060 can be configured in either SPI or manual mode, where the transmitter can easily be configured without the need of an SPI interface. In the 3V operation, the MAX7060 can be put in a lowpower shutdown mode by pulling ENABLE low and LSHDN high. In this mode, all the blocks are shut down including power-on reset (POR). All the MAX7060 registers must be reprogrammed after LSHDN is asserted high. In the 5V operation, the low-power shutdown mode is not available, and LSHDN should be connected to GND. Frequency Programming The MAX7060 is a crystal-referenced phased-lockedloop (PLL) VHF/UHF transmitter that transmits data over a wide frequency range. The internal VCO can be tuned from 280MHz to 450MHz and controlled by a single crystal to cover up to a 1.47:1 carrier-frequency range. The transmit frequency is set by the crystal frequency and the programmable divider in the PLL; the programmable PLL divide ratios can be set anywhere from 19 to 28, which means that with a crystal frequency of 15MHz, the output is 285MHz to 420MHz. With a crystal frequency of 16MHz, the output is 304MHz to 448MHz. The MAX7060 has an internal variable capacitor connected across the PA output. This capacitor can be programmed to maintain high-efficiency transmission at any frequency within a 1.47 to 1 (28/19) tuning range. This Maxim Integrated means that it is possible to change the frequency and retune the antenna to the new frequency in a very short time. The combination of rapid antenna-tuning ability with rapid synthesizer tuning makes the MAX7060 a true frequency-agile transmitter. The tuning capacitor has a nominal resolution of 0.25pF, from 0 to 7.75pF. The MAX7060 supports data rates up to 100kbps NRZ in ASK mode and 140kbps NRZ in FSK mode. In FSK mode, the frequency deviation corresponding to bit 1 and bit 0 can be set as low as Q2kHz, and as high as Q100kHz. The frequency deviation is fully programmable in SPI mode, and can be selected either as Q16kHz or Q50kHz in manual mode. Power Amplifier (PA) The PA of the MAX7060 is a high-efficiency, open-drain switching-mode amplifier. In a switching-mode amplifier, the gate of the final-stage FET is driven with a very sharp 25% duty-cycle square wave at the transmit frequency. This square wave is derived from the synthesizer circuit. When the matching network is tuned correctly, the output FET resonates the attached tank circuit with a minimum amount of power dissipated in the FET. With a proper output-matching network, the PA can drive a wide range of antenna impedances, which include a small-loop PCB trace and a 50I antenna. The output-matching network suppresses the carrier harmonics and transforms the antenna impedance to an optimal impedance at PAOUT, which is from 60I to 125I. When the output-matching network is properly tuned, the MAX7060 transmits power with a high overall efficiency. The efficiency of the PA itself is approximately 50%. Transmitter Power Control The transmitter power of the MAX7060 can be set in approximately 1dB steps (SPI mode) to produce a maximum output power level of +14dBm with a 5V supply. If a battery is used as the supply, the maximum output power level varies from +15dBm at 3.6V to +10dBm at 2.1V. The minimum power level is -14dBm for both 5V and battery supplies. The maximum transmitter power (and the transmitter current) can be lowered by increasing the load impedance on the PA. Four fixed power levels are available in manual mode. When a 5V supply is used, the VDD5 and GPOVDD pins are connected to the 5V supply. AVDD is the output of an internal voltage regulator and must be connected externally to DVDD and PAVDD. The PAVOUT pin is connected to the PAOUT pin through a biasing inductor. PAVOUT is not connected to any of the power-supply 13 MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter pins. Connecting PAVOUT to PAOUT enables Tx power control. In SPI mode, there are 31 power-control settings in approximately 1dB monotonic steps. In manual mode, four power-control settings are available. ASK Envelope Shaping The MAX7060 has two types of ASK envelope shaping: digital shaping (SPI mode only) and analog shaping through an internal resistor. Envelope shaping results in a smaller spectral width of the modulated PA output signal. In digital shaping, the user can choose the final Tx power setting, the power step size in units as small as 1dB, and the step-time interval in units as small as 0.25Fs, when a 16MHz crystal is used. This shaping method causes the PA to transmit an envelope that rises linearly in decibels (exponentially in power) with time. Digital shaping is programmed through the SPI. The analog shaping mode uses an internal envelopeshaping resistor for ASK modulation, which connects between PAVOUT and ROUT. When the ROUT pin (rather than the PAVOUT pin) is connected to the PA pullup inductor, the envelope-shaping resistor slows the turn-on/turn-off time of the PA. The user can choose two turn-on/turn-off times through the SPI. A single turn-on/ turn-off time is set internally in manual mode. It should be noted that, by default, data pulses applied to the DIN pin are internally lengthened by 64 crystal clock cycles (4s for a 16MHz crystal) to allow time for the analog shaping to occur. For cases in which no analog shaping is desired, the PA pullup inductor must be connected to PAVOUT and the analog shaping bits in the Conf0 register set to either anshp[1:0] = 00, which leaves the extra 4s pulse extension in place, or to anshp[1:0] = 11, which removes the extra 4s and allows transmitted pulses to track the data present at the DIN pin. If digital shaping is used, the PA pullup inductor must be connected to PAVOUT and there is no 4s pulse extension, regardless of the status of the anshp[1:0] bits. At low data rates, where shaping is not necessary and the 4s pulse lengthening has minimal impact on duty cycle symmetry, it may be acceptable to use the default configuration of anshp[1:0] = 00. For higher data rates, it may be necessary to use anshp[1:0] = 11, to avoid duty cycle skew. Another method to remove the pulse lengthening is to apply a minimal amount of digital shaping, by setting tstep[3:0] = 0001 and selecting pastep[4:0] = papwr[4:0]. 14 Variable Capacitor The MAX7060 has an internal set of capacitors that can be switched in and out to present different capacitor values at the PA output. The capacitors are connected from the PA output to ground. This allows changing the tuning network along with the synthesizer divide ratio each time the transmitted frequency changes, making it possible to maintain maximum transmitter power while moving rapidly from one frequency to another. In SPI mode, the variable capacitor is programmed through a register setting. In manual mode, the capacitor setting is programmed through the DIN pin. The tuning capacitor has a nominal resolution of 0.25pF, from 0 to 7.75pF. Phase-Locked Loop (PLL) The MAX7060 utilizes a fully integrated fractional-N PLL for its frequency synthesizer. All PLL components, including the loop filter, are included on-chip. Two loop bandwidths can be selected in SPI mode. The synthesizer has 16-bit fractional-N topology (4 bits integer, 12 bits fractional) with a divide ratio that can be set from 19 to 28, allowing the transmit frequency to be adjusted in increments of fXTAL/4096. The fractional-N architecture also allows exact FSK frequency deviations to be programmed, completely eliminating the problems associated with generating frequency deviations by crystal oscillator pulling. FSK deviations as low as Q2kHz and as high as Q100kHz can be set in SPI mode. In manual mode, the user can select between Q16kHz and Q50kHz. The integer and fractional portions of the PLL divider ratio set the transmit frequency. This is done by loading the divide-ratio registers in SPI mode, or selecting the states of the three frequency-control pins (FREQ2, FREQ1, FREQ0) in manual mode. For ASK modulation, the two 8-bit center-frequency registers (fce[15:0]) are loaded with the divide ratio determined by the center frequency and the crystal. For FSK modulation, the two 8-bit high (mark) frequency registers (fhi[15:0]) and the two 8-bit low (space) frequency registers (flo[15:0]) are loaded. The divide ratios for the fhi and flo are determined by the center frequency, the frequency deviation, and the crystal frequency. Examples of typical settings for ASK and FSK modulation are given in the SPI Mode Settings section. Maxim Integrated MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter Crystal (XTAL) Oscillator The XTAL oscillator in the MAX7060 is designed to present a capacitance of approximately 6pF between the XTAL1 and XTAL2 pins. In most cases, this corresponds to a 8pF load capacitance applied to the external crystal when typical PCB parasitics are added. It is very important to use a crystal with a load capacitance equal to the capacitance of the MAX7060 crystal oscillator plus PCB parasitics. If a crystal designed to oscillate with a different load capacitance is used, the crystal is pulled away from its stated operating frequency, introducing an error in the reference frequency. A crystal designed to operate at a higher load capacitance than the value specified for the oscillator is always pulled higher in frequency. Adding capacitance to increase the load capacitance on the crystal increases the startup time and can prevent oscillation altogether. In actuality, the oscillator pulls every crystal. The crystal's natural frequency is really below its specified frequency, but when loaded with the specified load capacitance, the crystal is pulled and oscillates at its specified frequency. This pulling is already accounted for in the specification of the load capacitance. Additional pulling can be calculated if the electrical parameters of the crystal are known. The frequency pulling is given by: fP = CM 1 1 6 - x 10 2 C CASE + C LOAD C CASE + C SPEC where: General-Purpose Output (GPO)/Clock Outputs The MAX7060 has two GPO pins in SPI mode (GPO2_ MOD and GPO1) and one GPO in manual mode (GPO1). The GPO1 pin can serve as a clock for a microprocessor or any other GPO function in SPI mode. In manual mode, this pin outputs the synthesizer lock-detect (lockdet) status, after which the user can send data through the DIN pin. The GPO2_MOD pin acts as the SPI data output when the CS_DEV pin is low, in SPI mode. When CS_DEV is high, it acts as a GPO that can output various internal signals, such as the synthesizer lock detect (lockdet). In SPI mode, the output clock that can be routed through GPO1 is a divided version of the crystal frequency. The divide ratio is set through the MAX7060 registers, and the divide settings are 1 (no division), 2, 4, 8, or 16. When driving an output clock through GPO1, the gp1bst bit (register Conf0, address 0x01, bit 6) can be set to 1 to increase GPO1 drive strength. If even more drive capability is required, the user should provide an external buffer. Serial Peripheral Interface (SPI) The MAX7060 utilizes a 4-wire SPI protocol for programming its registers, configuring and controlling the operation of the whole transmitter. For SPI operation, the FREQ2, FREQ1, and FREQ0 pins must be reset to 0. The following digital I/Os control the operation of the SPI: CS_DEV Active-low SPI chip select fP is the amount the crystal frequency pulled in ppm SDI_PWR1 SPI data Input CM is the motional capacitance of the crystal SCLK_PWR0 SPI clock CCASE is the case capacitance GPO2_MOD SPI data output CSPEC is the specified load capacitance CLOAD is the actual load capacitance When the crystal is loaded as specified (i.e., CLOAD = CSPEC), the frequency pulling equals zero. Maxim Integrated Figure 2 shows the general timing diagram of the SPI protocol. Any number of 8-bit data bursts (Data 1, Data 2 ... Data n) can be sent within one cycle of the CS_DEV pin, to allow for burst-write or burst-read operations. The SPI data output signal is routed through the GPO2_MOD pin when CS_DEV is low. 15 MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter CS_DEV SCLK_PWR0 SDI_PWR1 DI7 DI6 DI5 DI4 DI3 DI2 DI1 DI0 DI7 DI6 DI5 DI4 DI3 DI2 DI1 DI0 GPO2_MOD DO7 DO6 DO5 DO4 DO3 DO2 DO1 DO0 DO7 DO6 DO5 DO4 DO3 DO2 DO1 DO0 DATA 1 DATA n Figure 2. SPI Format SPI Commands The following commands are implemented in the MAX7060: Write: Within the same CS_DEV cycle, a write command is implemented as follows: SDI_PWR1: <0x01> ... With this command, Data 1 is written to the address given by , Data 2 is written to , and so on. Read: Within the same CS_DEV cycle, a read command is implemented as follows: SDI_PWR1: <0x02>
GPO2_MOD: <0xXX>
<0xXX>
...
... <0x00> With this command, all the registers can be read within the same cycle of CS_DEV. The addresses can be given in any order. CS_DEV SCLK_PWR0 SDI_PWR1 A7 WRITE COMMAND (0x01) A6 A5 A4 A3 A2 A1 INITIAL ADDRESS (A[7:0]) A0 D7 D6 D5 D4 D3 DATA 1 D2 D1 D0 D7 D0 DATA N Figure 3. SPI Write Command Format 16 Maxim Integrated MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter CS_DEV SCLK_PWR0 SDI_PWR1 A7 A6 A5 A4 READ COMMAND (0x02) A3 A2 A1 A0 A7 A6 A5 ADDRESS 1 A4 A3 A2 A1 A0 A7 ADDRESS 2 A0 ADDRESS N D7 D6 D5 D4 D3 D2 D1 D0 D7 GPO2_MOD DATA 1 0x00 D0 D7 DATA 2 D0 DATA N Figure 4. SPI Read Command Format Read All: Within two CS_DEV cycles, the read-all command is implemented as follows: CS_DEV Cycle 1 SDI_PWR1: <0x03>
GPO2_MOD: CS_DEV Cycle 2 <0x00> <0x00> <0x00> ... <0x00> ... Reset: An SPI reset command is implemented as follows: SDI_PWR1: <0x04> An internal active-low master reset pulse is generated, from the falling edge of the last SCLK_PWR0 signal to the falling edge of the following CS_DEV signal (tHCS + tCSH). CS_DEV SCLK_PWR0 SDI_PWR1 A7 A6 A5 A4 A3 A2 A1 A0 READ-ALL COMMAND (0x03) ADDRESS N GPO2_MOD D7 D6 D5 D4 D3 D2 D1 D0 D7 DATA N D0 D7 DATA N + 1 D0 DATA N + n Figure 5. SPI Read-All Command Format CS_DEV SCLK_PWRO SDI_PWR1 RESET COMMAND (0x04) INTERNAL RESET PULSE Figure 6. SPI Reset Command Format Maxim Integrated 17 MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter Applications Information SPI Mode Settings ASK Carrier Frequency When the MAX7060 is in ASK mode, only the carrier frequency needs to be set. To do this, the user calculates the divide ratio based on the carrier frequency and crystal frequency. The example below shows how to determine the correct value to be loaded into the carrierfrequency registers (fce[15:0]). Due to the nature of the transmit PLL frequency divider, a fixed offset of 16 must be subtracted from the transmit PLL divider ratio for programming the MAX7060's transmit-frequency registers. To determine the value to program the MAX7060's transmit-frequency registers, convert the decimal value of the following equation to the nearest hexadecimal value: fRF decimal value to program the - 16 x 4096 = transmit-frequency registers f XTAL Assume the ASK transmit frequency = 315MHz and fXTAL = 16MHz. In this example, the rounded decimal value is 15,104 or 0x3B00. The upper byte (0x3B) is loaded into the FCenter0 register (fce[15:8]) and the lower byte (0x00) is loaded into the FCenter1 register (fce[7:0]). FSK Mark and Space Frequencies When the MAX7060 is in FSK mode, two frequencies need to be set: the mark (logical 1) frequency and the space (logical 0) frequency. In most cases, the two frequencies are above and below the carrier frequency by the deviation frequency. Therefore, the user needs to calculate the divide ratio for both frequencies and load them into four registers. The procedure for calculating the register settings is the same as it is for calculating the carrier frequency. The example below shows how to determine the register settings for the mark and space frequencies when the frequency deviation is 50kHz (100kHz between mark and space). Assume that, for an FSK transmitter centered at 433.92MHz, the mark frequency is 433.97MHz, the space frequency is 433.87MHz, and the crystal frequency is 16MHz. In this example, the rounded decimal value for the mark frequency is 45,560 or 0xB1F8. For the space frequency, the rounded decimal value is 45,535 or 0xB1DE. The mark setting is loaded into the FHigh0 and FHigh1 registers (fhi[15:0]), and the space setting is loaded into the FLow0 and FLow1 registers (flo[15:0]). 18 Transmit Power Settings (5V Supply) The output power level is set by entering a 5-bit value into the PApwr register (papwr[4:0]). The highest setting (30dec or 0x1E) corresponds to the highest transmitted power level. Each step is slightly less than 1dB (approximately 0.95dB), with the lowest setting producing a transmitted power 28dB lower than the highest. The highest transmitted power depends on the load presented to the PA output. A 50I or 60I load produces an output power level of +14dBm to +15dBm when the highest papwr[4:0] setting (0x1E) is applied. Increasing the load resistance reduces the output power level. Reducing the setting by one step reduces the power by approximately 1dB, and the minimum transmitted power is still about 28dB below the maximum. For example, if the load resistance is increased to the point where the output power for the maximum setting (0x1E) is +10dBm, then the minimum setting (0x00) produces an output power of about -18dBm. Transmit Power Settings (3V Supply) The output power level in 3V operation is set the same way as in 5V operation, but the variation in the 3V supply (the specified range is 2.1V to 3.6V) affects the maximum power that can be transmitted. If the supply is 3.6V, then the maximum papwr[4:0] setting (0x1E) still produces a +14dBm to +15dBm transmitted power level. As the supply voltage decreases, the transmitted power at the highest settings is compressed, so that the top setting and an increasing number of the lower settings produce the same transmitted power, which is lower than the +14dBm to +15dBm achieved with a 3.6V supply. For example, a 2.7V supply produces a maximum transmitter power of +12dBm to +13dBm, and the PApwr register settings from 0x1B to 0x1E (27dec to 30dec) produce the same transmitter power. Below this compressed range, the power settings give the same power levels that they would give with a 5V supply. At the lowest supply level of 2.1V, the maximum setting produces a maximum transmitter power of +10dBm, and the PApwr register settings from 0x19 to 0x1E (25dec to 30dec) produce the same transmitter power. The effect of a lower supply voltage reduces the maximum power and the adjustment range. The power at the lowest setting remains unchanged. The transmitted power using a 3V supply can be set higher than the levels described in the paragraph above by connecting PAOUT directly to PAVDD and disconnecting (leave open) the PAVOUT pin. The tradeoff of this connection is that there is no transmit power adjustment. Maxim Integrated MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter ASK Amplitude Shaping At data rates higher than 30kbps Manchester (60kbps NRZ), it may be necessary to shape the ASK transmitter pulses to reduce the occupied bandwidth of the transmitted signal to comply with government regulations (FCC in the U.S., ETSI in Europe). There is no shaping of the FSK modulation. The MAX7060 has two forms of amplitude shaping: digital and analog. Digital Amplitude Shaping The digital shaping feature allows the user to choose a linear stairstep function to increase and decrease the power when the PA is turned on and off for an ASK bit interval. There are three registers that control the digital amplitude shaping settings. The first setting is the final power of the PA when the pulse reaches its maximum (PApwr register). The second setting is the amplitude change, in decibels, for each step, which is the vertical axis of the stairstep (PAstep register). The third setting is the time interval of each step, which is the horizontal axis of the stairstep (Tstep register). The final power setting (decimal 0 to 30 in increments of 1dB) is entered in the PApwr register. The amplitude step (decimal 0 to 30 in increments of 1dB) is entered in the PAstep register. The time interval (decimal 0 to 60/fXTAL in increments of 4/fXTAL) is entered in the Tstep register. For example, to shape an 80kbps NRZ data stream (12.5Fs bit interval), the user might choose a maximum power level of 0x1E (30dec), an amplitude step of 5dB, and a time interval of 0.5Fs assuming a crystal frequency of 16MHz. This would produce an ASK pulse that ramps up in 3Fs, levels off for 9.5Fs, and ramps down in 3Fs. Because the amplitude steps are in decibels, the shape of the pulse rise and fall is exponential on a linear display (an oscilloscope, for instance). Because most ASK receivers use a logarithmic amplitude detector, the demodulated pulse 12.5s has a linear ramp shape. The digital shaping is disabled when the Tstep register is 0x00. If no shaping of any kind is used (digital or analog), the PA pullup inductor must be connected to PAVOUT and the analog shaping bits in the Conf0 register must also be set to either anshp[1:0] = 00 or to anshp[1:0] = 11, as described in the ASK Envelope Shaping section. Analog Amplitude Shaping To use the analog shaping feature, the user must connect the bias inductor to the ROUT pin instead of directly to the PAVOUT pin. This places a MOS resistor between PAVOUT and ROUT, which slows down the application of the PAVOUT voltage to the drain of the PA FET when the PA is turned on. There are two settings in the anshp[1:0] bits in the Conf0 register for the rate at which the pulse ramps up: anshp[1:0] = 10 is approximately 1.5Fs and anshp[1:0] = 01 is approximately 3Fs. The anshp[1:0] = 11 setting turns analog shaping off and removes the 4Fs pulse extension, while the anshp[1:0] = 00 setting opens the connection between PAVOUT and ROUT. Tuning Capacitor Settings The internal variable shunt capacitor, which can be used to match the PA to the antenna with changing transmitter frequency, is controlled by setting the 5-bit cap variable in the registers. This allows for 32 levels of shunt capacitance control. Since the control of these 5 bits is independent of the other settings, any capacitance value can be chosen at any frequency, making it possible to maintain maximum transmitter efficiency while moving rapidly from one frequency to another. The internal tuning capacitor adds 0 to 7.75pF to the PA output in 0.25pF steps. The PA output capacitance at the minimum cap setting is approximately 4.5pF. 12.5s DIN PApwr = 0x1E (30dec) 0 PAstep = 0x05 (5dB) PAstep = 0x05 (5dB) Tstep = 0x2 (0.5s) Tstep = 0x2 (0.5s) Figure 7. Digital Amplitude Shaping Timing Diagram Maxim Integrated 19 MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter Register Details The following tables provide information on the MAX7060 registers. Table 1. Register Summary REGISTER ADDRESS DESCRIPTION Ident 0x00 Read-only register used for identification purpose. The content of this register is always 0xA6. Conf0 0x01 Configuration 0 register. Controls the GPO1 boost mode, PLL bandwidth, analog shaping, crystal clock output, and the modulation mode (ASK/FSK). Conf1 0x02 Configuration 1 register. Controls the clock output frequency divider and the capacitance at the PA output. Conf2 0x03 Configuration 2 register. Controls the emulation mode. IOConf0 0x04 IO configuration 0 register. Selects the status register bus for SPI operation. IOConf1 0x05 IO configuration 1 register. Selects the outputs of GPO1 and GPO2_MOD pins. Tstep 0x06 Digital shaping time step register. Controls the time step in the digital shaping. PAstep 0x07 Digital shaping power step register. Controls the power step in the digital shaping. PApwr 0x08 Final power register. Controls the final output power. FHigh0 0x09 High-frequency 0 register (upper byte). Sets the high frequency in FSK transmission. FHigh1 0x0A High-frequency 1 register (lower byte). Sets the high frequency in FSK transmission. FCenter0 0x0B Center-frequency 0 register (upper byte). Sets the carrier frequency in ASK transmission. FCenter1 0x0C Center-frequency 1 register (lower byte). Sets the carrier frequency in ASK transmission. FLow0 0x0D Low-frequency 0 register (upper byte). Sets the low frequency in FSK transmission. FLow1 0x0E Low-frequency 1 register (lower byte). Sets the low frequency in FSK transmission. FLoad 0x0F Frequency-load register. Performs the frequency-load function. EnableReg 0x10 Enable register. Register equivalent of ENABLE pin. DataReg 0x11 Datain register. Register equivalent of DIN pin. Status 0x12 Status register Table 2. Configuration Registers REGISTER ADDRESS DATA BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 Ident 0x00 1 0 1 0 0 1 1 0 MODE R Conf0 0x01 -- gp1bst pllbw anshp_1 anshp_0 clksby clkout mode R/W Conf1 0x02 ckdiv_2 ckdiv_1 ckdiv_0 cap_4 cap_3 cap_2 cap_1 cap_0 R/W Conf2 0x03 fixed fxmode fxpwr_1 fxpwr_0 fxhdev fxfrq_2 fxfrq_1 fxfrq_0 R/W IOConf0 0x04 -- -- -- -- -- tmux_2 tmux_1 tmux_0 R/W IOConf1 0x05 -- gp2s_2 gp2s_1 gp2s_0 -- gp1s_2 gp1s_1 gp1s_0 R/W Tstep 0x06 -- -- -- -- tstep_3 tstep_2 tstep_1 tstep_0 R/W PAstep 0x07 -- -- -- pastp_4 pastp_3 pastp_2 pastp_1 pastp_0 R/W PApwr 0x08 -- -- -- papwr_4 papwr_3 papwr_2 papwr_1 papwr_0 R/W FHigh0 0x09 fhi_15 fhi_14 fhi_13 fhi_12 fhi_11 fhi_10 fhi_9 fhi_8 R/W FHigh1 0x0A fhi_7 fhi_6 fhi_5 fhi_4 fhi_3 fhi_2 fhi_1 fhi_0 R/W FCenter0 0x0B fce_15 fce_14 fce_13 fce_12 fce_11 fce_10 fce_9 fce_8 R/W FCenter1 0x0C fce_7 fce_6 fce_5 fce_4 fce_3 fce_2 fce_1 fce_0 R/W 20 Maxim Integrated MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter Table 2. Configuration Registers (continued) REGISTER ADDRESS DATA BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 FLow0 0x0D flo_15 flo_14 flo_13 flo_12 flo_11 flo_10 flo_9 flo_8 MODE R/W FLow1 0x0E flo_7 flo_6 flo_5 flo_4 flo_3 flo_2 flo_1 flo_0 R/W FLoad 0x0F -- -- -- -- -- -- -- hop R/W EnableReg 0x10 -- -- -- -- -- -- -- enable R/W DataReg 0x11 -- -- -- -- -- -- -- datain R/W Status 0x12 status_7 status_6 status_5 status_4 status_3 status_2 status_1 status_0 R Table 3. Identification (Ident) Register (Address: 0x00) BIT NAME 7:0 ident FUNCTION Read-only register used for identification purpose. The content of this register is always 0xA6. Table 4. Configuration 0 (Conf0) Register (Address: 0x01) BIT NAME 6 gp1bst 5 pllbw FUNCTION 0 = Normal GPO1 output driver 1 = Extended driving capability on GPO1 PLL bandwidth setting, low (0) = 300kHz or high (1) = 600kHz; 300kHz is recommended for fractional-N and 600kHz for fixed-N (ASK mode only) Control time constants of the analog shaping (bias inductor connected to the ROUT pin) anshp[1:0] Rise/fall time 00 ROUT open-circuited, 4Fs pulse extension present 01 nominal 3.0Fs rise/fall time 10 nominal 1.5Fs rise/fall time 11 no analog shaping, no 4Fs pulse extension 4:3 anshp[1:0] 2 clksby Crystal clock output enable (1) while part is in standby mode 1 clkout Crystal clock output enable (1) on GPO1 output, gp1s[2:0] = 0x2 0 mode ASK (0) or FSK (1) Table 5. Configuration 1 (Conf1) Register (Address: 0x02) BIT NAME FUNCTION 7:5 ckdiv[2:0] 3-bit clock output frequency divider 4:0 cap[4:0] Maxim Integrated 5-bit capacitor setting Table 6. Crystal Divide Settings for Clock Output ckdiv[2:0] CRYSTAL FREQUENCY DIVIDED BY 000 1 001 2 010 4 011 8 1XX 16 21 MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter Table 7. Configuration 2 (Conf2) Register (Address: 0x03) BIT NAME 7 fixed 6 fxmode 5:4 fxpwr[1:0] 3 fxhdev 2:0 fxfrq[2:0] FUNCTION Enable (1) or disable (0) emulation mode FSK (1) or ASK (0) Output power setting fxpwr[1:0] dB below PMAX 00 0 01 3 10 6 11 10 100kHz (1) or 32kHz (0) frequency deviation in FSK Frequency selection The combinations are same as those in manual mode. When a 16MHz crystal is used, the following frequency values are selected by fxfrq[2:0]. fxfrq[2:0] Freq (MHz) Divide Ratio 000 N/A N/A 001 315.00 19.68750 010 433.62 27.10125 011 390.00 24.37500 100 418.00 26.12500 101 372.00 23.25000 110 345.00 21.56250 111 433.92 27.12000 Table 8. IO Configuration 0 (IOConf0) Register (Address: 0x04) BIT NAME 2:0 tmux[2:0] 22 FUNCTION Status register output selection bits Maxim Integrated MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter Table 9. IO Configuration 1 (IOConf1) Register (Address: 0x05) BIT 6:4 2:0 NAME FUNCTION gp2s[2:0] GPO2 output selection CS_DEV Bit 2 0 X 1 0 1 0 1 0 1 0 1 1 1 1 1 1 1 1 gp1s[2:0] GPO1 output selection Bit 2 Bit 1 Bit 0 0 0 0 0 0 1 0 1 0 0 1 1 1 0 0 1 0 1 1 1 0 1 1 1 Bit 1 X 0 0 1 1 0 0 1 1 Bit 0 X 0 1 0 1 0 1 0 1 GPO2_MOD SPI Data Output lockdet -- ckout -- -- nock -- -- GPO1 lockdet -- ckout -- -- nock -- -- where: -- Reserved signals nock No-clock flag (1) if crystal oscillator is disabled, and (0) if clock activity is observed ckout Clock output signal, according to programmed dividers (ckdiv[2:0]) lockdet PLL lock-detect flag Table 10. ASK Digital Shaping Time Step (Tstep) Register (Address: 0x06) BIT NAME 3:0 tstep[3:0] FUNCTION Time interval value used in digital shaping, in increments of 4/fXTAL Table 11. PA Digital Shaping Amplitude Step (PAstep) Register (Address: 0x07) BIT NAME 4:0 pastp[4:0] FUNCTION Power step in digital shaping, in increments of 1dB Table 12. PA Power (PApwr) Register (Address: 0x08) BIT NAME 4:0 papwr[4:0] FUNCTION Final PA output power setting Table 13. FSK High-Frequency 0 (FHigh0) Register (Address: 0x09) BIT NAME 7:0 fhi[15:8] Maxim Integrated FUNCTION 8-bit upper byte of high-frequency divider for FSK 23 MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter Table 14. FSK High-Frequency 1 (FHigh1) Register (Address: 0x0A) BIT NAME 7:0 fhi[7:0] FUNCTION 8-bit lower byte of high-frequency divider for FSK The 4 MSBs of FHigh0, fhi[15:12], are the integer portion of the divider, excluding offset of 16. The 12 LSBs (fhi[11:0]) are the fractional part of the divider. Table 15. ASK Center-Frequency 0 (FCenter0) Register (Address: 0x0B) BIT NAME 7:0 fce[15:8] FUNCTION 8-bit upper byte of frequency divider for ASK Table 16. ASK Center-Frequency 1 (FCenter1) Register (Address: 0x0C) BIT NAME 7:0 fce[7:0] FUNCTION 8-bit lower byte of frequency divider for ASK The 4 MSBs of FCenter0, fce[15:12], are the integer portion of the divider, excluding offset of 16. The 12 LSBs (fce[11:0) are the fractional part of the divider. When fce[11:0] are all zeros and ASK mode is selected (mode bit = 0), the PLL works in the fixed-N mode, which reduces current consumption and reference spurs. Set pllbw bit high (Conf0 register, bit 5). For all other combinations, the PLL works in fractional-N mode. Table 17. FSK Low-Frequency 0 (FLow0) Register (Address:0x0D) BIT NAME 7:0 flo[15:8] FUNCTION 8-bit upper byte of low-frequency divider for FSK Table 18. FSK Low-Frequency 1 (FLow1) Register (Address: 0x0E) BIT NAME 7:0 flo[7:0] FUNCTION 8-bit lower byte of low-frequency divider for FSK The 4 MSBs of FLow0, flo[15:12], are the integer portion of the divider, excluding offset of 16. The 12 LSBs (flo[11:0]) are the fractional part of the divider. Table 19. Maximum and Minimum Values for Frequency Divider DECIMAL VALUE fhi[15:0], fce[15:0], flo[15:0] 12.0220 0xC05A 2.9536 0x2F42 Table 20. Frequency-Load (FLoad) Register (Address: 0x0F) BIT NAME FUNCTION 0 hop Effectively changes the PLL frequency to the ones written in registers 0x09 to 0x0E. This is a self-reset bit and is reset to zero after the operation is completed. 24 Maxim Integrated MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter Table 21. Enable (EnableReg) Register (Address: 0x10) BIT NAME 0 enable FUNCTION SPI equivalent of the ENABLE pin, which should be kept low (0) if the external ENABLE pin is used. The external ENABLE pin should also be kept low (0) if the enable bit is used. Table 22. Data Input (DataReg) Register (Address: 0x11) BIT NAME FUNCTION 0 datain SPI equivalent of DIN, where the transmitted data can be controlled through the SPI interface. It should be kept low (0) if only the external DIN pin is used. The external DIN pin should also be kept low (0) if the datain bit is used. Table 23. Status (Status) Register (Address: 0x12) BIT NAME 7:0 status[7:0] FUNCTION Read-only status register, selected through tmux[2:0] (register 0x04 IOConf0) Table 24. Status Bus Signals tmux[2:0] 0 status[7] -- status[6] -- status[5] -- status[4] -- status[3] ckout status[2] ckd16 status[1] ckd4 status[0] nock 1 -- -- -- -- -- -- -- -- 2 -- -- -- -- enable -- -- -- 3 -- frac_fxdb -- cap[4] cap[3] cap[2] cap[1] cap[0] 4 -- -- notover capfxd[4] capfxd[3] capfxd[2] capfxd[1] capfxd[0] 5 integ[3] integ[2] integ[1] integ[0] frac[11] frac[10] frac[9] frac[8] 6 frac[7] frac[6] frac[5] frac[4] frac[3] frac[2] frac[1] frac[0] 7 -- -- -- -- -- -- lockdet xmit_en -- Reserved signals nockNo-clock flag (1) if crystal oscillator is disabled, and (0) ic clock activity is observed ckd4 Crystal clock signal divided by 4 ckd16 Crystal clock signal divided by 16 frac_fxdbFractional-N mode (1) or ASK fixed-N mode (0) capfxd[4:0] Emulation mode variable capacitor setting notoverASK digital shaping flag (1) when PA power value is different than 0 ckout Clock output signal, according to programmed dividers (ckdiv[2:0]) integ[3:0] Fractional-N 4-bit integer value frac[11:0] Fractional-N 12-bit fractional value enableInternal enable signal (OR function of the ENABLE pin and enable bit) xmit_en Transmitter PA enable flag lockdet PLL lock-detect flag cap[4:0] SPI mode capacitor setting Maxim Integrated 25 MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter Manual Mode Settings Frequency Selection There are seven internally set fractional-N divide ratios that correspond to commonly used frequencies when a 16MHz crystal is used. The MAX7060 can be operated by controlling certain pins directly, thereby eliminating the need for an SPI controller. There is a restricted selection of frequency and power settings, but operation is simpler. The pins that are used in manual mode are as follows: Notice that the MAX7060 can be operated manually at any single frequency over its 280MHz to 450MHz operating range by choosing a crystal frequency and one of the divide ratios from Table 25. For example, a transmitting frequency of 308MHz can be achieved by selecting the 19.68750 divide ratio and a 15.6444MHz crystal. Pin 1:GPO2_MOD (modulation mode, 0 = ASK, 1 = FSK) Pins 5, 6, 7: FREQ0, FREQ1, FREQ2 Pin 19:CS_DEV (FSK deviation selection, 0 = Q16kHz, 1 = Q50kHz) The frequency settings in the manual mode of operation were designed in a way that allows the customer to toggle only one control line between low and high states to switch between seven commonly used frequency pairs (see Table 26). Pins 20, 21:SDI_PWR1 and SCLK_PWR0 (2-pin power selection) Pins 22, 23: ENABLE and DIN (PA variable capacitor setting, data input, enable) ASK or FSK Modulation Reset pin 1 (GPO2_MOD) to 0 for ASK modulation and 1 for FSK modulation. Analog shaping in ASK mode is enabled by using the ROUT pin. The turn-on and turn-off time is fixed at approximately 1s. To put the MAX7060 in manual mode, set any of the FREQ0, FREQ1, FREQ2 pins (5, 6, and 7) to logic-high. These pins are normally pulled down, so the default state of the MAX7060 is for SPI operation. The settings in Table 25 can be made in manual mode. Table 25. Manual Mode Frequency Selection FREQ2 FREQ1 FREQ0 FREQUENCY (MHz) DIVIDE RATIO 0 0 0 SPI N/A 0 0 1 315.00 19.68750 0 1 0 433.62 27.10125 0 1 1 390.00 24.37500 1 0 0 418.00 26.12500 1 0 1 372.00 23.25000 1 1 0 345.00 21.56250 1 1 1 433.92 27.12000 Table 26. Manual Mode Frequency Pair Switching LOW FREQUENCY (MHz) HIGH FREQUENCY (MHz) 315.00 433.92 26 FREQ2, FREQ1, FREQ0 001 to 111. Set FREQ0 high, shorting FREQ1 and FREQ2, toggling 1 line. 418.00 433.92 100 to 111. Set FREQ2 high, shorting FREQ1 and FREQ0, toggling 1 line. 433.62 433.92 010 to 111. Set FREQ1 high, shorting FREQ2 and FREQ0, toggling 1 line. 315.00 390.00 001 to 011. Set FREQ0 high and FREQ2 low, toggling FREQ1. 315.00 372.00 001 to 101. Set FREQ1 low and FREQ0 high, toggling pin FREQ2. 345.00 433.92 110 to 111. Set FREQ2 and FREQ1 high, toggling FREQ0. 390.00 433.92 011 to 111. Set FREQ1 and FREQ0 high, toggling FREQ2. Maxim Integrated MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter Table 27. Output Power Settings SDI_PWR1 SCLK_PWR0 dB BELOW PMAX 0 0 0 0 1 3 1 0 6 1 1 10 Frequency Deviation Reset pin 19 (CS_DEV) to 0 for 32kHz (Q16kHz) FSK deviation and 1 for 100kHz (Q50kHz) FSK deviation. Transmitter Power Set SDI_PWR1 (pin 20) and SCLK_PWR0 (pin 21) to four power settings (relative to the maximum power setting). Note that at battery voltages below 3V, the top two power settings are compressed and the power difference is less than 3dB. PA Variable Capacitor Setting In manual mode, capacitance can be added to the PA output for one selected frequency. This allows the user to adjust the matching network when switching between two frequencies in the manual selection table, or for switching to one frequency that is significantly different from the others in the table. The user can set the capacitance by resetting the ENABLE pin to a logic-low, then selecting the frequency for which the variable capacitor is to be added from the seven possible settings, and then sending a stream of 1 to 32 pulses through the DIN pin. The first pulse is used to reset the internal capacitor counter and to latch the selected frequency. After the first pulse, the remaining number of pulses sent equals the variable capacitor setting. When the ENABLE pin goes high, the capacitor setting for the specified frequency is set, so that it adds the programmed capacitance to the PA when the chosen frequency is selected. This scheme must be executed only once to set the value of the variable capacitor. For example, a user can operate the MAX7060 at 315MHz and 433.92MHz into a narrowband antenna by resetting the ENABLE pin low, setting the FREQ0, FREQ1, FREQ2 pins to 001 (315MHz), and sending the appropriate number of pulses into the DIN pin, and then setting the ENABLE pin high. When the frequency is set to 433.92MHz (or any other frequency in the table except 315MHz), no capacitance is added to the PA output. Maxim Integrated When the frequency is set to 315MHz, the PA capacitance increases by the programmed value. Figure 8 illustrates how to set the capacitance. It begins with the ENABLE pin pulled low. The frequency is sampled at the rising edge of the first pulse. Pulses 2-11 set the capacitance code to 0x0A (10dec), which is approximately 2.5pF. The ENABLE pin is then pulled high to finish the setting. Emulation Mode Settings All the settings available through the manual mode of operation are also easily accessible in the SPI mode. This mode is called emulation mode, whereby only writing one or two registers, the whole transmitter can be configured. The Conf2 register controls this mode. The emulation mode is a subset of SPI mode. It gives SPI users the capability to operate the part by programming just one or two registers instead of all registers. Since it is still SPI mode, pins 5, 6, and 7 (FREQ0, FREQ1, and FREQ2) must be pulled low. The Conf2 register is the only register that needs to be programmed. Setting bit 7 (fixed) to 1 enables this mode. Bit 6 (fxmode) is equivalent to pin 1 (GPO2_MOD) in manual mode. Bits 5 and 4 (fxpwr[1:0]) are equivalent to pin 20 and 21 (SDI_PWR1 and SCLK_PWR0) in manual mode. Bit 3 (fxhdev) is equivalent to pin 19 (CS_DEV) in manual mode. Bits 2, 1, and 0 (fxfrq[2:0]) are equivalent to pins 5, 6, and 7 (FREQ0, FREQ1, and FREQ2) in manual mode. Similar to manual mode, the PA capacitor setting in the emulation mode can be done by toggling the DIN pin with the ENABLE pin low. In addition, the capacitor setting can also be done by directly writing to the capacitor register (bits 4:0 of the Conf1 register, cap[4:0]). As long as the capacitor register value is not zero, the capacitor value sent in by toggling the DIN pin is ignored. Control Interface Considerations When operating the MAX7060 with a +4.5V to +5.5V supply voltage, the CS_DEV, SCLK_PWR0, SDI_PWR1, FREQ0, FREQ1, FREQ2, ENABLE, DIN, and LSHDN pins can be driven by a microcontroller with either 3V or 5V interface logic levels. When operating the MAX7060 with a +2.1V to +3.6V supply, the microcontroller must produce logic levels that conform to the VIH and VIL specifications in the DC Electrical Characteristics for the MAX7060. 27 MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter ENABLE FREQ[2:0] X 0x1 DIN CAP CODE CAPTURED CAP VALUE X 0x0A Figure 8. Variable Capacitor Setting Timing Diagram Typical Application Circuits SPI Mode (5V Supply) Y1 C1 C2 19 20 21 22 DIGITAL CONTROLLER 23 24 C4 +3VREG C3 +5V C5 18 17 16 XTAL1 XTAL2 AVDD C7 C6 15 14 C8 13 N.C. VDD5 PAVOUT ROUT CS_DEV 12 L1 +3VREG SDI_PWR1 PAVDD 11 C9 SCLK_PWR0 MAX7060 ENABLE PAOUT EXPOSED PAD DIN N.C. LSHDN N.C. FREQ2 GPO2_MOD 1 GPO1 DVDD GPOVDD 2 3 +3VREG C12 4 10 9 Tx ANTENNA C10 MATCHING NETWORK COMPONENTS 8 7 FREQ0 FREQ1 5 6 C11 +5V 28 Maxim Integrated MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter Typical Application Circuits (continued) Manual Mode (3V Supply, Shaped ASK Modulation, 315MHz) C1 C2 19 20 21 22 23 24 DIGITAL CONTROLLER C4 Y1 +3V +3V C5 C3 18 17 16 XTAL1 XTAL2 AVDD C6 15 14 C7 13 N.C. VDD5 PAVOUT ROUT CS_DEV SDI_PWR1 PAVDD SCLK_PWR0 12 +3V C9 MAX7060 ENABLE PAOUT EXPOSED PAD DIN N.C. LSHDN N.C. FREQ2 GPO2_MOD GPO1 1 2 DVDD 3 C12 GPOVDD FREQ0 4 +3V C8 11 5 C10 10 9 Tx ANTENNA L1 MATCHING NETWORK COMPONENTS 8 7 FREQ1 6 C11 Component List DESIGNATION QTY C1, C4 2 May not be needed for low CLOAD crystals, depending on PCB layout parasitics C2, C3 2 1.5nF 10%, 50V X7R ceramic capacitors (0603) Murata GRM188R71H152K C5, C6 2 100nF 10%, 50V X7R ceramic capacitors (0603) Murata GRM188R71H104K C7, C8, C9 3 220pF 5% ceramic capacitors (0603) Murata GRM1885C1H220JA01D C10, C11, C12 3 10nF 10%, 50V X7R ceramic capacitors (0603) Murata GRM188R71H103K L1 1 5% wire-wound inductor (0603) Murata LQW18 series (value depends on matching network) 4 3 capacitors and 1 inductor (values depend on frequency range and antenna impedance) 1 Maxim MAX7060ATG+ 1 16MHz crystal, 10pF CLOAD Crystek 17466 Suntsu SCX284 Matching Network Components U1 Y1 Maxim Integrated DESCRIPTION 29 MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter Package Information Chip Information PROCESS: CMOS 30 For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE PACKAGE CODE OUTLINE NO. LAND PATTERN NO. 24 TQFN-EP T2444+3 21-0139 90-0021 Maxim Integrated MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter Revision History REVISION NUMBER REVISION DATE 0 2/10 Initial release 2/12 Power dissipation and derating factor shown for wrong package type; clarified GPO1 boost mode and nature of analog and digital ASK envelope shaping. Added paragraph on control interface considerations; updated Typical Application Circuits to add exposed pad (grounded); and specified typical load C on crystal in component list 1 DESCRIPTION PAGES CHANGED -- 2, 14, 15, 19, 21, 27, 28, 29 Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. Maxim Integrated 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000 (c) 2012 Maxim Integrated 31 Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Maxim Integrated: MAX7060ATG/V+ MAX7060ATG/V+T MAX7060ATG+ MAX7060ATG+T