REVISIONS
LTR DESCRIPTION DATE (YR-MO-DA) APPROVED
C Redrawn with changes. Add device types 04 and 05. Add case
outline H. Editorial changes throughout. 94-03-04
M.A. Frye
D Add device types 06 and 07. Table I changes. Editorial changes
throughout. 95-01-18
M.A. Frye
E Changes in accordance with NOR 5962-R037-96.
96-01-11 M.A. Frye
F Changes in accordance with NOR 5962-R072-96.
96-03-15
M.A. Frye
G Update boiler plate and incorporate previous 2 NORs. Redrawn.
Updated bulletin. -lgt 98-06-26
R. Monnin
H Add figure 1 so that a change to symbol “A” dimension can be
specified under case outline letter H. - ro 03-07-25 R. Monnin
THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.
REV
SHEET
REV H H
SHEET 15 16
REV STATUS REV H H H H H H H H H H H H H H
OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14
PMIC N/A PREPARED BY
RICK OFFICER
DEFENSE SUPPLY CENTER COLUMBUS
STANDARD
MICROCIRCUIT
DRAWING
CHECKED BY
CHARLES E. BESORE
COLUMBUS, OHIO 43216
http://www.dscc.dla.mil
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
APPROVED BY
MICHAEL A. FRYE
MICROCI RCUIT, LINEAR, SINGLE POWER
MOSFET DRIVER, MONOLITHIC SILICON
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
DRAWING APPROVAL DATE
89-08-16
AMSC N/A
REVISION LEVEL
H SIZE
A CAGE CODE
67268
5962-88770
SHEET
1 OF
16
DSCC FORM 2233
APR 97 5962-E452-03
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimit ed.
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-88770
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL
H SHEET 2
DSCC FORM 2234
APR 97
1. SCOPE
1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in
accordance with MIL-PRF-38535, appendix A.
1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example:
5962-88770 01 H X
Drawing number
Device type
(see 1.2.1) Case outline
(see 1.2.2) Lead finish
(see 1.2.3)
1.2.1 Device type(s). The device type(s) identify the circuit function as follows:
Device type Generic number Circuit function Output
01 TSC429 Inverting power MOSFET driver 4.5 A dc
02 TSC4429 Inverting power MOSFET driver 4.5 A dc
03 TSC4420 Noninverting power MOSFET driver 4.5 A dc
04 MIC4451 Inverting hi speed, hi current MOSFET driver 12 A dc
05 MIC4452 Noninverting hi speed, hi current MOSFET driver 12 A dc
06 MIC44R21 Inverting, rad hardened MOSFET driver 9 A dc
07 MIC44R22 Noninverting, rad hardened MOSFET driver 9 A dc
1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter Descriptive designator Terminals Package style
H See figure 1 10 Flat pack
P GDIP1-T8 or CDIP2-T8 8 Dual-in-line
2 CQCC1-N20 20 Square leadless chip carrier
1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A.
1.3 Absolute maximum ratings.
Supply voltage (VS)............................................................. 20 V dc
Input voltage range (VIN) :
Device 01 ........................................................................ VS + 0.3 V dc to GND - 0.3 V dc
Devices 02, 03, 04, 05 .................................................... VS + 0.3 V dc to GND - 5.0 V dc
Output current (per pin, capacitance load) :
Devices 01 – 03 .............................................................. 6.0 A dc
Devices 04 – 05 .............................................................. 12.0 A dc
Devices 06 – 07 .............................................................. 9.0 A dc
Peak supply current or GND current (per pin) :
Devices 01 – 03 .............................................................. 6.0 A dc
Devices 04 – 05 .............................................................. 12.0 A dc
Devices 06 – 07 .............................................................. 9.0 A dc
Storage temperature range ................................................ -55°C to +125°C
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-88770
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL
H SHEET 3
DSCC FORM 2234
APR 97
1.3 Absolute maximum ratings - continued.
Power dissipation (PD) :
Case outline H .................................................................... 650 mW 1/
Case outline P .................................................................... 800 mW 2/
Case outline 2 .................................................................... 1.8 W 3/
Lead temperature (soldering, 10 seconds) ............................ +300°C
Junction temperature range (TJ) ............................................ -55°C to +150°C
1.4 Recommended operating conditions.
Supply voltage range ............................................................. 4.5 V dc ≤ VS ≤ 18 V dc
Ambient operating temperature range (TA) ........................... -55°C to +125°C
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a
part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed
in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in
the solicitation.
SPECIFICATION
DEPARTMENT OF DEFENSE
MIL-PRF-38535 -- Integrated Circuits, Manufacturing, General Specification for.
STANDARDS
DEPARTMENT OF DEFENSE
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard Electronic Component Case Outlines.
HANDBOOKS
DEPARTMENT OF DEFENSE
MIL-HDBK-103 -- List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
____
1/ Derate linearly at 6.5 mW/°C above TA = +50°C.
2/ Derate linearly at 8 mW/°C above TA = +50°C.
3/ Derate linearly at 18 mW/°C above TA = +50°C.
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-88770
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL
H SHEET 4
DSCC FORM 2234
APR 97
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-
JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer
Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-
PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying
activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan
may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device.
These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MIL-
PRF-38535 is required to identify when the QML flow option is used.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as
specified in MIL-PRF-38535, appendix A and herein.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full ambient operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are described in table I.
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN
listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked as listed in MIL-HDBK-103 (see 6.6 herein). For
packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the
option of not marking the "5962-" on the device.
3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance
to MIL-PRF-38535, appendix A. The compliance indicator “C” sha ll be replaced with a "Q" or "QML" certification mark in
accordance with MIL-PRF-38535 to identify when the QML flow option is used.
3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an
approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to
listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF-
38535, appendix A and the requirements herein.
3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided
with each lot of microcircuits delivered to this drawing.
3.8 Notification of change. Notification of change to DSCC-VA shall be required in accordance with MIL-PRF-38535,
appendix A.
3.9 Verification and review. DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's
facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the
reviewer.
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-88770
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL
H SHEET 5
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics.
Test Symbol Conditions
-55°C ≤ TA ≤+125°C
4.5 ≤ VS ≤ 18 V
Group A
subgroups Device
type Limits Unit
unless otherwise specified Min Max
Logic “1” input voltage
VIH 1, 2, 3 01-05 2.4 V
06, 07 3.5
Logic “0” input voltage
VIL 1, 2, 3 01-05 0.8 V
06, 07 2.0
Input voltage range
VIN
(max)
1, 2, 3 01 0 VS V
1, 2, 3 02, 03
04, 05 -5 VS
+0.3
Input current
IIN 0 V ≤ VIN ≤ VS 1 ALL ±1 µA
2, 3 ±10
-5 V ≤ VIN ≤ 0 V 1, 2, 3 02, 03,
07 ±10 mA
High output voltage
VOH R
L = ∞ 1/ 1, 2, 3 ALL VS - 25
mV V
Low output voltage
VOL R
L = ∞ 1/ 1, 2, 3 ALL 25 mV
Output resistance
RO1 V
S = 18 V, VIN = 0.8 V,
1 01, 03 2.5
Ω
IOUT = 10 mA 2, 3 5.0
1 02 2.8
2, 3 5.0
1 04, 05 1.5
2, 3 2.2
1 06, 07 2.5
2, 3 3.6
See footnotes at end of table.
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-88770
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL
H SHEET 6
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics - Continued.
Test Symbol Conditions
-55°C ≤ TA ≤+125°C
4.5 ≤ VS ≤ 18 V
Group A
subgroups Device
type Limits Unit
unless otherwise specified Min Max
Output resistance
RO2 V
S = 18 V, VIN = 2.4 V, 1 01, 02 2.5
Ω
IOUT = 10 mA 2, 3 5.0
1 03 2.8
2, 3 5.0
1 04, 05 1.5
2, 3 2.2
VS = 18 V, VIN = 3.5 V, 1 06, 07 1.7
IOUT = 10 mA 2, 3 2.7
Quiescent supply
current IS1 V
IN = 3.0 V 1 01 5.0 mA
2, 3 12
1 02, 03
04, 05, 1.5
2, 3 06, 07 3.0
IS2 V
IN = 0.0 V 1 01 0.5
2, 3 1.3
1 02, 03 0.15
2, 3 0.40
1 04, 05, 0.15
2, 3 06, 07 0.4
See footnotes at end of table.
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-88770
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL
H SHEET 7
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics - Continued.
Test Symbol Conditions
-55°C ≤ TA ≤+125°C
4.5 ≤ VS ≤ 18 V
Group A
subgroups Device
type Limits Unit
unless otherwise specified Min Max
Rise time
tR V
S = 18 V, CL = 2500 pF 2/ 9 01 35 ns
see figures 3 and 4 10, 11 70
9 02, 03 35
10, 11 60
VS = 18 V, CL = 15,000 pF, 2/ 9 04, 05 75
see figures 3 and 4 10, 11 100
VS = 18 V, CL = 10,000 pF, 2/ 9 06, 07 75
see figures 3 and 4 10, 11 120
Fall time
tF V
S = 18 V, CL = 2500 pF 2/ 9 01 35 ns
see figures 3 and 4 10, 11 70
9 02, 03 35
10, 11 60
VS = 18 V, CL = 15,000 pF, 2/ 9 04, 05 75
see figures 3 and 4 10, 11 100
VS = 18 V, CL = 10,000 pF, 2/ 9 06, 07 75
see figures 3 and 4 10, 11 120
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-88770
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL
H SHEET 8
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics - Continued.
Test Symbol Conditions
-55°C ≤ TA ≤+125°C
4.5 ≤ VS ≤ 18 V
Group A
subgroups Device
type Limits Unit
unless otherwise specified Min Max
Delay time tD1 V
S = 18 V, 2/ 9 01, 02
03 75 ns
see figures 3 and 4 10, 11 100
9 04, 05, 60
10, 11 06, 07 80
tD2 9 01 75
10, 11 120
9 02, 03 75
10, 11 100
9 04, 05, 60
10, 11 06, 07 80
1/ Guaranteed by design.
2/ Subgroups 10 and 11 are guaranteed if not tested to the limits as specified in table I herein.
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-88770
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL
H SHEET 9
DSCC FORM 2234
APR 97
Case outline H
Configuration A - metal-sealed, bottom brazed leads
FIGURE 1. Case ou t line.
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-88770
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL
H SHEET 10
DSCC FORM 2234
APR 97
Case outline H
Configuration B - Ceramic, glass sealed
FIGURE 1. Case ou t line – Continued.
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-88770
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL
H SHEET 11
DSCC FORM 2234
APR 97
Case outline H
FIGURE 1. Case ou t line – Continued.
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-88770
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL
H SHEET 12
DSCC FORM 2234
APR 97
1/ Configuration A and B
Symbol
Min Max Note
A .045 .105
b .010 .022
b1 .010 .019 2
c .004 .009
c1 .004 .006 2
D --- .280 3
E .240 .260
E1 --- .300 3
E2 .125 ---
E3 .030 --- 7
e .050 BSC
k .008 .015 2
L .250 .370
Q .026 .045 9
S1 .005 --- 6
M --- .0015 2
N 10
NOTES:
1. Index area: A notch or a pin one identification mark shall be located adjacent to pin one and shall be
located within the shaded area shown. The manufacturer's identification shall not be used as a pin
one identification mark. Alternatively, a tab (dimension k) may be used to identify pin one. This tab
may be located on either side of terminal one as shown in detail A, or it may be located on terminal
one as shown in detail B.
2. If a pin one identification mark is used in addition to a tab, the limits of dimension k do not apply.
3. This dimension allows for off-center lid, meniscus, and glass overrun.
4. Dimensions b1 and c1 apply to lead base metal only. Dimension M applies to lead plating and finish
thickness. The maximum limits of lead dimensions b and c or M shall be measured at the centroid of
the finished lead surfaces, when solder dip or tin plate lead finish is applied.
5. N is the maximum number of terminal positions.
6. Measure dimension S1 at all four corners, see 5.2.5 of MIL-STD-1835. There is an alternative
minimum limit to dimension S1, see 5.2.2 of MIL-STD-1835.
7. For bottom-brazed lead packages, no organic or polymeric materials shall be molded to the bottom of
the package to cover the leads.
8. Optional, see note 1. If a pin one identification mark is used in addition to this tab, the minimum limit
of dimension k does not apply.
9. Dimension Q shall be measured at the point of exit (beyond the meniscus) of the lead from the body.
Dimension Q minimum shall be reduced by .0015 inch (0.038 mm) maximum when solder dip lead
finish is applied.
FIGURE 1. Case ou t line – Continued.
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-88770
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL
H SHEET 13
DSCC FORM 2234
APR 97
Device types 01, 02, 03,
04, 05, 06, 07 01, 02, 03,
04, 05, 06, 07 01, 02, 03
Case outlines
H P 2
Terminal
number Terminal symbol
1
VS V
S NC
2
INPUT INPUT NC
3
NC NC VS
4
GND GND NC
5
NC GND NC
6
NC OUTPUT INPUT
7
GND OUTPUT NC
8
OUTPUT VS NC
9
OUTPUT --- GND
10
VS --- NC
11
--- --- NC
12
--- --- NC
13
--- --- GND
14
--- --- NC
15
--- --- OUTPUT
16
--- --- OUTPUT
17
--- --- NC
18
--- --- NC
19
--- --- VS
20
--- --- NC
FIGURE 2. Terminal connections.
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-88770
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL
H SHEET 14
DSCC FORM 2234
APR 97
FIGURE 3. Inverting driver switching time.
FIGURE 4. Noninverting driver switching time.
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-88770
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL
H SHEET 15
DSCC FORM 2234
APR 97
4. QUALITY ASSURANCE PROVISIONS
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535,
appendix A.
4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices
prior to quality conformance inspection. The following additional criteria shall apply:
a. Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision
level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall
specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in
test method 1015 of MIL-STD-883.
(2) TA = +125°C, minimum.
b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-
883 including groups A, B, C, and D inspections. The following additional criteria shall apply.
4.3.1 Group A inspection.
a. Tests shall be as specified in table II herein.
b. Subgroups 4, 5, 6, 7, and 8 in table I, method 5005 of MIL-STD-883 shall be omitted.
4.3.2 Groups C and D inspections.
a. End-point electrical parameters shall be as specified in table II herein.
b. Steady-state life test conditions, method 1005 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision
level control and shall be made available to the preparing or acquiring activity upon request. The test circuit
shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent
specified in test method 1005 of MIL-STD-883.
(2) TA = +125°C, minimum.
(3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-88770
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL
H SHEET 16
DSCC FORM 2234
APR 97
TABLE II. Electrical test requirements.
MIL-STD-883 test requirements Subgroups
(in accordance with
MIL-STD-883, method 5005,
table I)
Interim electrical parameters
(method 5004) ---
Final electrical test parameters
(method 5004) 1*,2,3
Group A test requirements
(method 5005) 1,2,3,9,10,**,11**
Groups C and D end-point
electrical parameters
(method 5005)
1
* PDA applies to subgroup 1.
** Subgroups 10 and 11, if not tested, shall be guaranteed to the
specified limits in table I.
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A.
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
(original equipment), design applications, and logistics purposes.
6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-
prepared specification or drawing.
6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for
the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal.
6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus when a system application
requires configuration control and the applicable SMD. DSCC will maintain a record of users and this list will be used for
coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC 5962)
should contact DSCC-VA, telephone (614) 692-0544.
6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Columbus, Ohio 43216-5000, or telephone
(614) 692-0547.
6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103. The vendors listed in MIL-
HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted
by DSCC-VA.
STANDARD MICROCIRCUIT DRAWI NG BULLETIN
DATE: 03-07-25
Approved sources of supply for SMD 5962-88770 are listed below for immediate acquisition information only and shall be
added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised to include
the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has
been submitted to and accepted by DSCC-VA. This bulletin is superseded by the next dated revision of MIL-HDBK-103 and
QML-38535.
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-8877001HA 3/ MIC429AWBQ
5962-8877001PA 3/ MIC429AJBQ
5962-88770012A 3/ TSC429MNP/883
5962-8877002HA 3/ MIC4429AWBQ
5962-8877002PA 1ES66 MAX4429MJA/883B
5962-88770022C 1ES66 MAX4429MLP/883B
5962-8877003HA 3/ MIC4420AWBQ
5962-8877003PA 60496 MIC4420AJBQ
1ES66 MAX4420MJA/883B
5962-88770032C 1ES66 MAX4420MLP/883B
5962-8877004HA 3/ MIC4451AWBQ
5962-8877004PA 3/ MIC4451AJBQ
5962-8877005HA 3/ MIC4452AWBQ
5962-8877005PA 3/ MIC4452AJBQ
See footnotes at end of table.
Page 1 of 2
STANDARD MICROCIRCUIT DRAWING SOURCE APPROVAL BULLETIN - Continued
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-8877006HA 3/ MIC44R21AWBQ
5962-8877006PA 3/ MIC44R21AJBQ
5962-8877007HA 3/ MIC44R22AWBQ
5962-8877007HC 69210 OM9422SFM
5962-8877007PA 3/ MIC44R22AJBQ
1/ The lead finish shown for each PIN representing
a hermetic package is the most readily available
from the manufacturer listed for that part. If the
desired lead finish is not listed contact the vendor
to determine its availability.
2/ Caution. Do not use this number for item acquisition.
Items acquired to this number may not satisfy the
performance requirements of this drawing.
3/ Not available from an approved source of supply.
Vendor CAGE Vendor name
number and address
60496 Micrel Inc.
1849 Fortune Drive
San Jose, CA 95131-1724
69210 Omnirel Corporation
205 Crawford Street
Leominster, MA 01453-2353
1ES66 Maxim Integrated Products Inc.
120 San Gabriel Drive
Sunnyvale, CA 94086-5125
2 of 2
The information contained herein is disseminated for convenience only and the
Government assumes no liability whatsoever for any inaccuracies in the
information bulletin.
