PRODUCT DESCRIPTION
Konform SR High Viscosity provides
maximum coverage where good flexibility is
required, or where extreme temperatures can
be encountered. This transparent coating
provides ideal protection for both rigid and
flexible printed circuit boards. Cured
coatings are hydrolyticly stable and retain
their physical electrical properties after high
temperature and humidity exposure.
Konform SR High Viscosity will not stress
delicate circuit components.
Extends component life by protecting against
adverse environments
Good insulation properties, excellent
flexibility
Resists moisture, salt, fungus, corrosive
vapors, and severe environments
Engineered to withstand heat generated by
electronic circuitry as well as climatic
temperatures
Contains a UV indicator for thorough Quality
Control inspection
TYPICAL APPLICATIONS
Konform SR High Viscosity is ideal for
applications in:
Aerospace
Data Communications
Instrumentation
Automotive Manufacturing
Marine Manufacturing
Process Control
TYPICAL PRODUCT DATA AND
PHYSICAL PROPERTIES
Usable Temp. Range (-85°F to 390°F)
of Cured Coatings (-65°C to 200°C)
Tack Free Time 30 Min. to 1 Hour
Curing Conditions 24 Hours @ 77°F (25°C)
(@ 80% R.H.) 8 Hours @ 170°F (77°C)
Specific Gravity 1.00
(Water=1) @ 68
°
F
Viscosity (cps @ 77
°
F) 120 cps
Flash Point (TCC) 60°F
Volume Resistivity 1.5 x 10
16
(ohm/cm)
Dielectric Strength (volts/mil) 1100
Coefficient of Thermal 2.1 x 10
-4
Expansion (in/in/
°
C)
Coverage 718.5
(2 mil/ft2)
Shelflife
1 year
COMPATIBILITY
Konform SR High Viscosity is generally
compatible with most materials found on
printed circuit boards. As with any chemical
product, product/component compatibility
must be determined on a non-critical area
prior to use.
TDS # CTSRHV
CHEMTRONICS
Technical Data Sheet
Konform
SR High Viscosity
Performance
Moisture Resistance
Excellent
Removability
Excellent
Ease of Repair
Excellent
Flexibility
Excellent
Adhesion
Excellent
Abrasion Resistance
Fair
Solvent Resistance
Good
USAGE INSTRUCTIONS
For industrial use only.
Read MSDS carefully prior to use.
Before applying Konform SR High Viscosity
conformal coatings, clean circuit boards to
remove contamination and allow to dry.
Cleaning may be performed with Chemtronics
Electro-Wash PX, Electro-Wash CZ, or high
purity acetone.
SPRAY APPLICATION: Apply top to
bottom, allowing coating to flow evenly around
components. Rotate PCB 90° and repeat
application. Rotate and apply coating two
additional times, then allow board to cure. If
additional thickness is desired, apply additional
coatings. When using liquid spray with
automatic dispensing equipment, adjustments
may be required in application rate and viscosity.
DIP APPLICATION: Using automatic
equipment or hand immersion technique, slowly
immerse PCB into the coating and remove
slowly. Use an average rate of approximately 1
foot per minute. After allowing the board to
cure, process may be repeated to achieve desired
thickness.
BRUSH APPLICATIONS: Evenly apply
coating to areas desired at thickness required.
Allow time for curing before reapplying to
achieve a thick coating. Use Chemask to
protect components during conformal coating
process.
REMOVAL: After application, cured
Konform SR High Viscosity may be removed
by soaking in Chemtronics Electro-Wash Two
Step, or an aromatic solvent (such as xylene), or
a short chain ketone (such as acetone).
AVAILABILITY
CTSR-HV1 1 Gal. Liquid
CTSR-HV5 5 Gal. Liquid
TECHNICAL & APPLICATION
ASSISTANCE
Chemtronics provides a technical hotline to
answer your technical and application related
questions. The toll free number is: 1-800-
TECH-401.
NOTE:
This information is believed to be accurate. It is
intended for professional end users having the
skills to evaluate and use the data properly.
CHEMTRONICS does not guarantee the
accuracy of the data and assumes no liability in
connection with damages incurred while using it.
CHEMTRONICS
8125 COBB CENTER DRIVE
KENNESAW, GA 30152
1-770-424-4888 REV. A (08/13)
Chemtronics, Electro-Wash, Chemask,and Konform are
registered trademarks of Chemtronics. All rights reserved.
DISTRIBUTED BY:
