HY57V643220C-I Series 4 Banks x 512K x 32Bit Synchronous DRAM DESCRIPTION The Hynix HY57V643220C is a 67,108,864-bit CMOS Synchronous DRAM, ideally suited for the Mobile applications which require low power consumption and extended temperature range. HY57V643220C is organized as 4banks of 524,288x32. HY57V643220C is offering fully synchronous operation referenced to a positive edge of the clock. All inputs and outputs are synchronized with the rising edge of the clock input. The data paths are internally pipelined to achieve very high bandwidth. All input and output voltage levels are compatible with LVTTL. Programmable options include the length of pipeline (Read latency of 2 or 3), the number of consecutive read or write cycles initiated by a single control command (Burst length of 1,2,4,8 or full page), and the burst count sequence(sequential or interleave). A burst of read or write cycles in progress can be terminated by a burst terminate command or can be interrupted and replaced by a new burst read or write command on any cycle. (This pipelined design is not restricted by a 2N rule.) FEATURES * JEDEC standard 3.3V power supply * Auto refresh and self refresh * All device pins are compatible with LVTTL interface * 4096 refresh cycles / 64ms * JEDEC standard 400mil 86pin TSOP-II with 0.5mm of pin pitch * Programmable Burst Length and Burst Type * All inputs and outputs referenced to positive edge of system clock - 1, 2, 4, 8 or full page for Sequential Burst - 1, 2, 4 or 8 for Interleave Burst * Data mask function by DQM0,1,2 and 3 * Programmable CAS Latency ; 2, 3 Clocks * Internal four banks operation * Burst Read Single Write operation ORDERING INFORMATION Part No. Clock Frequency HY57V643220CT-5I 200MHz HY57V643220CT-55I 183MHz HY57V643220CT-6I 166MHz HY57V643220CT-7I 143MHz HY57V643220CT-SI 100MHz HY57V643220CLT-5I 200MHz HY57V643220CLT-55I 183MHz HY57V643220CLT-6I 166MHz HY57V643220CLT-7I 143MHz HY57V643220CLT-SI 100MHz Power Organization Interface Package 4Banks x 512Kbits x32 LVTTL 400mil 86pin TSOP II Normal Low-Power This document is a general product description and is subject to change without notice. Hynix semiconductor does not assume any responsibility for use of circuits described. No patent licenses are implied. Rev. 0.6 / Apr. 2003 1 HY57V643220C-I PIN CONFIGURATION VDD DQ0 VDDQ DQ1 DQ2 VSSQ DQ3 DQ4 VDDQ DQ5 DQ6 VSSQ DQ7 NC VDD DQM0 /W E /C A S /R A S /C S NC BA0 BA1 A 1 0 /A P A0 A1 A2 DQM2 VDD NC D Q 16 VSSQ D Q 17 D Q 18 VDDQ D Q 19 D Q 20 VSSQ D Q 21 D Q 22 VDDQ D Q 23 VDD 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 8 6 p in T S O P II 4 0 0 m il x 8 7 5 m il 0 .5 m m p in p itc h 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 VSS DQ 15 VSSQ DQ 14 DQ 13 VDDQ DQ 12 DQ 11 VSSQ DQ 10 DQ9 VDDQ DQ8 NC VSS DQM 1 NC NC CLK CKE A9 A8 A7 A6 A5 A4 A3 DQM 3 VSS NC DQ 31 VDDQ DQ 30 DQ 29 VSSQ DQ 28 DQ 27 VDDQ DQ 26 DQ 25 VSSQ DQ 24 VSS PIN DESCRIPTION PIN PIN NAME DESCRIPTION CLK Clock The system clock input. All other inputs are registered to the SDRAM on the rising edge of CLK. CKE Clock Enable Controls internal clock signal and when deactivated, the SDRAM will be one of the states among power down, suspend or self refresh CS Chip Select Enables or disables all inputs except CLK, CKE and DQM BA0, BA1 Bank Address Selects bank to be activated during RAS activity Selects bank to be read/written during CAS activity A0 ~ A10 Address Row Address : RA0 ~ RA10, Column Address : CA0 ~ CA7 Auto-precharge flag : A10 RAS, CAS, WE Row Address Strobe, Column Address Strobe, Write Enable RAS, CAS and WE define the operation Refer function truth table for details DQM0~3 Data Input/Output Mask Controls output buffers in read mode and masks input data in write mode DQ0 ~ DQ31 Data Input/Output Multiplexed data input / output pin VDD/VSS Power Supply/Ground Power supply for internal circuits and input buffers VDDQ/VSSQ Data Output Power/Ground Power supply for output buffers NC No Connection No connection Rev. 0.6 / Apr. 2003 2 HY57V643220C-I FUNCTIONAL BLOCK DIAGRAM 512Kbit x 4banks x 32 I/O Synchronous DRAM Self R efresh Logic & Tim er Internal R ow C ounter 512K x32 B ank 3 C LK R ow A ctive C olum n Pre D ecoders Y decoders B ank Select A0 A1 DQ0 I/O Buffer & Logic M em ory C ell Array Sense AMP & I/O Gate C olum n A ctive X decoders WE DQM0 DQM1 DQM2 DQM3 512K x32 B ank 0 X decoders CAS 512K x32 B ank 1 X decoders RAS State Machine CS 512K x32 B ank 2 X decoders CKE R ow Pre D ecoders DQ1 D Q 30 D Q 31 C olum n A dd C ounter Address R egister Address buffers A 10 BA0 BA1 Rev. 0.6 / Apr. 2003 Burst C ounter M ode R egisters C AS Latency D ata O ut C ontrol P ipe Line C ontrol 3 HY57V643220C-I ABSOLUTE MAXIMUM RATINGS Parameter Symbol Rating Unit Ambient Temperature TA -40 ~ 85 C Storage Temperature TSTG -55 ~ 125 C Voltage on Any Pin relative to VSS VIN, VOUT -1.0 ~ 4.6 V Voltage on VDD relative to VSS VDD, VDDQ -1.0 ~ 4.6 V Short Circuit Output Current IOS 50 mA Power Dissipation PD 1 W Soldering Temperature Time TSOLDER 260 10 C Sec Note : Operation at above absolute maximum rating can adversely affect device reliability DC OPERATING CONDITION (TA= -40 to 85C) Parameter Symbol Min Typ. Max Unit Note Power Supply Voltage VDD, VDDQ 3.0 3.3 3.6 V 1,2 Input high voltage VIH 2.0 3.0 VDDQ + 0.3 V 1,3 Input low voltage VIL VSSQ - 0.3 0 0.8 V 1,4 Note Note : 1.All voltages are referenced to VSS = 0V 2.VIH (max) is acceptable 5.6V AC pulse width with 3ns of duration with no input clamp diodes 3.VIL (min) is acceptable -2.0V AC pulse width with 3ns of duration with no input clamp diodes AC OPERATING CONDITION (TA= -40 to 85C, 3.0V VDD 3.6V, VSS=0V - Note1) Parameter Symbol Value Unit VIH / VIL 2.4/0.4 V Vtrip 1.4 V Input rise / fall time tR / tF 1 ns Output timing measurement reference level Voutref 1.4 V CL 30 pF AC input high / low level voltage Input timing measurement reference level voltage Output load capacitance for access time measurement 1 Note : 1.Output load to measure access times is equivalent to two TTL gates and one capacitor (30pF) For details, refer to AC/DC output load circuit Rev. 0.6 / Apr. 2003 4 HY57V643220C-I CAPACITANCE (TA=25C, f=1MHz, VDD=3.3V) Parameter Pin Input capacitance Data input / output capacitance Symbol Min Max Unit CLK CI1 2.5 4 pF A0 ~ A10, BA0, BA1, CKE, CS, RAS, CAS, WE, DQM0~3 CI2 2.5 5 pF DQ0 ~ DQ31 CI/O 4 6.5 pF OUTPUT LOAD CIRCUIT Vtt=1.4V Vtt=1.4V RT=500 Output RT=50 Z0 = 50 Output 30pF 30pF DC Output Load Circuit AC Output Load Circuit DC CHARACTERISTICS I (DC operating conditions unless otherwise noted) Parameter Symbol Min. Max Unit Note Input leakage current ILI -1 1 uA 1 Output leakage current ILO -1.5 1.5 uA 2 Output high voltage VOH 2.4 - V IOH = -2mA Output low voltage VOL - 0.4 V IOL = +2mA Note : 1.VIN = 0 to 3.6V, All other pins are not under test = 0V 2.DOUT is disabled, VOUT=0 to 3.6V Rev. 0.6 / Apr. 2003 5 HY57V643220C-I DC CHARACTERISTICS II (DC operating conditions unless otherwise noted) Speed Parameter Symbol Test Condition -5I -55I -6I -7I -SI 200 190 180 170 150 IDD1 Burst Length=1, One bank active tRAS tRAS(min), tRP tRP(min), IOL=0mA IDD2P CKE VIL(max), tCK = 15ns 2 IDD2PS CKE VIL(max), tCK = 2 IDD2N CKE VIH(min), CS VIH(min), tCK = 15ns Input signals are changed one time during 2clks. All other pins VDD-0.2V or 0.2V 15 IDD2NS CKE VIH(min), tCK = Input signals are stable. 10 IDD3P CKE VIL(max), tCK = 15ns 3 IDD3PS CKE VIL(max), tCK = 3 IDD3N CKE VIH(min), CS VIH(min), tCK = 15ns Input signals are changed one time during 2clks. All other pins VDD-0.2V or 0.2V 40 IDD3NS CKE VIH(min), tCK = Input signals are stable 25 Burst Mode Operating Current IDD4 tCK tCK(min), tRAS tRAS(min), IOL=0mA All banks active Auto Refresh Current IDD5 tRRC tRRC(min), All banks active Self Refresh Current IDD6 CKE 0.2V Operating Current Precharge Standby Current in power down mode Precharge Standby Current in non power down mode Active Standby Current in power down mode Active Standby Current in non power down mode Unit Note mA 1 mA mA mA mA CL=3 280 260 240 210 160 CL=2 - - - 160 140 250 240 230 220 190 mA 1 mA 2 2 mA 3 1 mA 4 Note : 1.IDD1 and IDD4 depend on output loading and cycle rates. Specified values are measured with the output open 2.Min. of tRRC (Refresh RAS cycle time) is shown at AC CHARACTERISTICS II 3.HY57V643220CT-5I/55I/6I/7I/SI 4.HY57V643220CLT-5I/55I/6I/7I/SI Rev. 0.6 / Apr. 2003 6 HY57V643220C-I AC CHARACTERISTICS I (AC operating conditions unless otherwise noted) -5I Parameter System clock cycle time CAS Latency = 3 -55I -6I -7I -SI Symbol tCK3 Unit Min Max Min Max Min Max Min 5 1000 5.5 1000 6 1000 7 Max Min 10 1000 Note Max ns 1000 tCK2 - - - - - - -10 Clock high pulse width tCHW 2 - 2.25 - 2.5 - 3 - 3.5 - ns 1 Clock low pulse width tCLW 2 - 2.25 - 2.5 - 3 - 3.5 - ns 1 CAS Latency = 3 tAC3 - 4.5 - 5 - 5.5 - 5.5 - 6 ns CAS Latency = 2 tAC2 - - - - - - - 6 - 6 ns Data-out hold time tOH 1.5 - 2 - 2 - 2 - 2 - ns 3 Data-Input setup time tDS 1.5 - 1.5 - 1.5 - 1.75 - 2.5 - ns 1 Data-Input hold time tDH 1 - 1 - 1 - 1 - 1 - ns 1 Address setup time tAS 1.5 - 1.5 - 1.5 - 1.75 - 2.5 - ns 1 Address hold time tAH 1 - 1 - 1 - 1 - 1 - ns 1 CKE setup time tCKS 1.5 - 1.5 - 1.5 - 1.75 - 2.5 - ns 1 CKE hold time tCKH 1 - 1 - 1 - 1 - 1 - ns 1 Command setup time tCS 1.5 - 1.5 - 1.5 - 1.75 - 2.5 - ns 1 Command hold time tCH 1 - 1 - 1 - 1 - 1 - ns 1 CLK to data output in low Z-time tOLZ 1 - 1 - 1 - 1 - 1 - ns CAS Latency = 3 tOHZ3 - 4.5 - 5 - 5.5 - 5.5 - 6 ns CAS Latency = 2 tOHZ2 - - - - - - - 6 - 6 ns Access time from clock CLK to data output in high Z-time CAS Latency = 2 12 ns 2 Note : 1.Assume tR / tF (input rise and fall time ) is 1ns 2.Access times to be measured with input signals of 1v/ns edge rate, 0.8v to 2.0v 3.Data-out hold time to be measured under 30pF load condition, without Vt termination Rev. 0.6 / Apr. 2003 7 HY57V643220C-I AC CHARACTERISTICS II (AC operating conditions unless otherwise noted) -5I Parameter -55I -6I -7I -SI Symbol Unit Min Max Min Max Min Max Min Max Min Max Operation tRC 55 - 55 - 60 - 63 - 70 - ns Auto Refresh tRRC 55 - 55 - 60 - 63 - 70 - ns RAS to CAS delay tRCD 15 - 16.5 - 18 - 20 - 20 - ns RAS active time tRAS 38.7 100K 38.7 100K 42 100K 42 100K 50 100K ns RAS precharge time tRP 15 - 16.5 - 18 - 20 - 20 - ns RAS to RAS bank active delay tRRD 2 - 2 - 2 - 2 - 2 - CLK CAS to CAS delay tCCD 1 - 1 - 1 - 1 - 1 - CLK Write command to data-in delay tWTL 0 - 0 - 0 - 0 - 0 - CLK Data-in to precharge command tDPL 2 - 2 - 2 - 2 - 2 - CLK Data-in to active command tDAL 4 - 4 - 5 - 5 - 4 - ns DQM to data-out Hi-Z tDQZ 2 - 2 - 2 - 2 - 2 - CLK DQM to data-in mask tDQM 0 - 0 - 0 - 0 - 0 - CLK MRS to new command tMRD 2 - 2 - 2 - 2 - 2 - CLK CAS Latency = 3 tPROZ3 3 - 3 - 3 - 3 - 3 - CLK CAS Latency = 2 tPROZ2 - - - - - - 2 - 2 - CLK Power down exit time tPDE 1 - 1 - 1 - 1 - 1 - CLK Self refresh exit time tSRE 1 - 1 - 1 - 1 - 1 - CLK Refresh Time tREF - 64 - 64 - 64 - 64 - 64 ms Not e RAS cycle time Precharge to data output Hi-Z 1 Note : 1. A new command can be given tRRC after self refresh exit Rev. 0.6 / Apr. 2003 8 HY57V643220C-I DEVICE OPERATING OPTION TABLE HY57V643220C(L)T-5I CAS Latency tRCD tRAS tRC tRP tAC tOH 200MHz(5ns) 3CLKs 3CLKs 38.5ns 11CLKs 3CLKs 4.5ns 1.5ns 183MHz(5.5ns) 3CLKs 3CLKs 38.5ns 10CLKs 3CLKs 5ns 2ns CAS Latency tRCD tRAS tRC tRP tAC tOH 183MHz(5.5ns) 3CLKs 3CLKs 7CLKs 10CLKs 3CLKs 5ns 2ns 166MHz(6ns) 3CLKs 3CLKs 7CLKs 10CLKs 3CLKs 5.5ns 2ns tRCD tRAS tRC tRP tAC tOH HY57V643220C(L)T-55I HY57V643220C(L)T-6I CAS Latency 166MHz(6ns) 3CLKs 3CLKs 7CLKs 10CLKs 3CLKs 5.5ns 2.0ns 143MHz(7ns) 3CLKs 3CLKs 6CLKs 9CLKs 3CLKs 5.5ns 2.0ns HY57V643220C(L)T-7I CAS Latency tRCD tRAS tRC tRP tAC tOH 143MHz(7ns) 3CLKs 3CLKs 6CLKs 9CLKs 3CLKs 5.5ns 2.0ns 100MHz(10ns) 2CLKs 2CLKs 5CLKs 7CLKs 2CLKs 6ns 2.0ns CAS Latency tRCD tRAS tRC tRP tAC tOH 100MHz(10ns) 3CLKs 2CLKs 5CLKs 7CLKs 2CLKs 6ns 2.0ns 83MHz(12ns) 2CLKs 2CLKs 5CLKs 7CLKs 2CLKs 6ns 2.5ns HY57V643220C(L)T-SI Rev. 0.6 / Apr. 2003 9 HY57V643220C-I COMMAND TRUTH TABLE Command A10/ AP CKEn-1 CKEn CS RAS CAS WE DQM Mode Register Set H X L L L L X OP code H X X X No Operation H X X X L H H H Bank Active H X L L H H X H X L H L H X ADDR RA Read L V H Write L H X L H L L X CA Write with Autoprecharge H X L L H L X Burst Stop H DQM H Auto Refresh H H L L L Burst-READ-Single-WRITE H X L L Entry H L L H Exit L H H X L H H L X L V X X V X H X X L L X A9 Pin High (Other Pins OP code) L L H X X X X X X X L H H H H X X X L H H H H X X X L H H H H X X X L V V V L Precharge power down H X Precharge selected Bank Entry V H Precharge All Banks X X Exit Clock Suspend Note V CA Read with Autoprecharge Self Refresh1 BA Entry Exit L H L H X L H X X X X Note : 1. Exiting Self Refresh occurs by asynchronously bringing CKE from low to high 2. X = Dont care, H = Logic High, L = Logic Low. BA =Bank Address, RA = Row Address, CA = Column Address, Opcode = Operand Code, NOP = No Operation Rev. 0.6 / Apr. 2003 10 HY57V643220C-I PACKAGE INFORMATION 400mil 86pin Thin Small Outline Package Unit : mm(inch) 11.938(0.4700) 11.735(0.4620) 22.327(0.8790) 22.149(0.8720) 10.262(0.4040) 10.058(0.3960) 0.150(0.0059) 0.050(0.0020) 0.50(0.0197) Rev. 0.6 / Apr. 2003 0.21(0.008) 0.18(0.007) 1.194(0.0470) 0.991(0.0390) 5deg 0deg 0.597(0.0235) 0.406(0.0160) 0.210(0.0083) 0.120(0.0047) 11