Application Specification 114-1075 Z-PACK* 2mm FB (Futurebus+) Receptacle and Pin Header Connectors NOTE i 23 MAR 09 Rev D All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters. Unless otherwise specified, dimensions have a tolerance of +0.13 and angles have a tolerance of +2 . Figures and illustrations are for identification only and are not drawn to scale. _ 1. INTRODUCTION This specification covers the requirements for application of the Z-PACK 2mm FB (Futurebus+) Receptacle and Pin Header Connectors for printed circuit (pc) board applications. The connectors have in-row and row-to-row centerline spacing of 2mm. They are available in either 4- or 5-row configurations. The connectors use an open pin field construction (no ground planes) for high signal density and require minimal pc board space. The receptacles are right-angle configurations and the pin headers are both vertical and right-angle configurations; both are available with either solder tine or press-fit compliant pin contacts. Accessories and their identifying features are described and shown in Section 3 of this specification. When corresponding with Tyco Electronics Personnel, use the terminology provided on this specification to help facilitate your inquiry for information. Basic terms and features of components are provided in Figure 1. 4-Row Right-Angle Power Receptacle Connector Alignment Rib Press-Fit 4-Row Right-Angle Signal Receptacle Connectors Compliant Pin Contact Power Receptacle Contacts (Inside) Solder Tine Contact Back/Top Surface of Housing Power Pin Contact Alignment Rib Slot Signal Receptacle Press-Fit Contacts (Inside) Compliant with Guide-In Pin Contact End Stabilizers Signal Pin Contact Center Stabilizer Plastic Retention Post Retention Post Seating Area Solder Tine Contact Guide Post for Solder Type Only 4-Row Vertical Power Pin Header Connector Standoff 4-Row Vertical Signal Pin Header Connectors Contact Shoulder Figure 1 (cont'd) E 2009 Tyco Electronics Corporation, Harrisburg, PA All International Rights Reserved TOOLING ASSISTANCE CENTER 1-800-722-1111 This controlled document is subject to change. PRODUCT INFORMATION 1-800-522-6752 For latest revision and Regional Customer Service, TE logo and Tyco Electronics are trademarks. *Trademark. Other products, logos, and company names used are the property of their respective owners. visit our website at www.tycoelectronics.com 1 of 15 LOC B Z-PACK 2mm FB Connectors 114-1075 5-Row Right-Angle Power Receptacle Connector Alignment Rib Press-Fit Compliant Pin Contact Power Receptacle 5-Row Right-Angle Signal Receptacle Connectors Contacts (Inside) Solder Tine Back/Top Surface Contact of Housing Press-Fit Signal Receptacle Compliant Contacts (Inside) Pin Contact Power Pin Contact End Alignment Rib Slot Stabilizers with Guide-In Center Stabilizer Signal Pin Plastic Retention Contact Post Solder Tine Contact Guide Post for Solder Type Only Retention Post 5-Row Vertical Power Pin Header Connector Seating Area Standoff 5-Row Vertical Signal Pin Header Connectors Contact Shoulder Figure 1 (end) 2. REFERENCE MATERIAL 2.1. Revision Summary This paragraph is reserved for a revision summary of the most recent additions and changes made to this specification which include the following: S Updated document to corporate requirements S Deleted obsolete part numbers and documents in Paragraph 2.6 and Section 5, TOOLING S Changed dimension line in Figure 5 2 of 15 Tyco Electronics Corporation Rev D Z-PACK 2mm FB Connectors 114-1075 2.2. Customer Assistance Reference Part Number 536507 and Product Code 1830 are representative numbers of Z-PACK 2mm FB Receptacle and Pin Header Connectors. Use of these numbers will identify the product line and expedite your inquiries through a service network established to help you obtain product and tooling information. Such information can be obtained through a local Tyco Electronics Representative or, after purchase, by calling the Tooling Assistance Center or Product Information number at the bottom of page 1. 2.3. Drawings Customer Drawings for specific products are available from the service network. The information contained in Customer Drawings takes priority if there is a conflict with this specification or with any other technical documentation supplied by Tyco Electronics 2.4. Manuals Manual 402-40 is available from the service network. This manual provides information on various flux types and characteristics along with the commercial designation and flux removal procedures. A checklist is included in the manual as a guide for information on soldering problems. 2.5. Specifications Product Specification 108-1441 provides test and performance requirements. 2.6. Instructional Material The following list includes available instruction sheets (408-series) that provide assembly procedures for product, operation, maintenance and repair of tooling, as well as setup and operation procedures of applicators. Document Number 408-4038 408-4157 408-4250 408-4488 408-9910 408-9979 Document Title PC Board Support Fixtures 679980-1, -2 for Z-PACK 2mm FB (Futurebus) and 2mm HM Receptacle Tooling Vertical Power Contact Header Connector Seating Tool 58512-[ ] (4-Row) Vertical Signal Contact Header Connector Seating Tool 318860-[ ] (5-Row) Vertical Power Contact Header Connector Seating Tool 1214224-[ ] (5-Row) Vertical Signal Contact Header Connector Seating Tools 58511-[ ] (4-Row) Pin Repair Kit 354687-1 3. REQUIREMENTS 3.1. Storage and Chemical Exposure Limitations A. Storage Connectors are packaged and shipped in protective anti-static tubes. To prevent damage to the housing and contact tines, connectors should remain in tubes until ready for use. They should be stored at normal room temperatures with low humidity, and used on a first in, first out basis. B. Chemical Exposure Limitations Do not store connectors near any chemicals listed, as they may cause stress corrosion cracking in the components. Alkalies Amines Rev D Ammonia Carbonates Citrates Nitrites Phosphates Citrates Sulfur Nitrites Tyco Electronics Corporation Sulfur Compounds Tartrates 3 of 15 Z-PACK 2mm FB Connectors 114-1075 3.2. Connector Features A. Materials All Z-PACK 2mm FB Connector Housings are constructed of high-temperature thermoplastic. The signal and power pin contacts are phosphor bronze and plated at the contact interface with gold flash over palladium-nickel. The signal receptacle contacts are copper alloy and plated at the contact interface with a gold flash over palladium-nickel. Power receptacle contacts are beryllium copper and plated at interface with a gold flash over palladium-nickel. All contacts have a nickel underplate and tin or tin-lead tines. B. Size Connectors are available in three types: all-signal, all-power, and signal/power mix. The 4-row signal connectors are available in a range of 12-mm-length (24 positions) to 132-mm-length (264 positions) in increments of 12 mm. Also, the 4-row power connectors are available in 12-mm-length (8 positions) only. The 5-row signal connectors are available in a range of 12-mm-length (30 positions) to 132-mm-length (330 positions) in increments of 12 mm. Also, the 5-row power connectors are available in 12-mm-length (10 positions) only. Signal/power mix connectors are available in any configuration in a range of 24 mm to 132 mm in increments of 12 mm. The contact type and length for each connector type is provided in Figure 2. Vertical Pin Header Connector Right-Angle Receptacle Connector Right-Angle Pin Header Connector A A C C B NOTE: 4-row shown, 5-row is the same for dimensioning purposes. CONNECTOR CONTACT DIMENSION (Length) TYPE CONFIGURATION TYPE A Solder Signal g Right-Angle g g Header g g Right-Angle Receptacle Vertical Pin Header C 3.20, 4.25 Vertical Pin Header B 5 0 5 5.0, 5.75, 75 6 6.5, 5 Compliant Pin 7.25, 8.0 4.25, 11.8, 13.6, --- 15.6, 17.0 Solder 2.73 5 0 5.0 --- Compliant Pin 3.35 Solder 2.73, 3.53 --- --- Compliant Pin 3.55 Solder 3.20, 4.25, 6 5 7.25, 6.5, 7 25 8.0 8 0 Compliant Pin --4.25 Power Right-Angle g g Receptacle Solder 2.73, 3.53 --- Compliant Pin --3.56 Figure 2 4 of 15 Tyco Electronics Corporation Rev D Z-PACK 2mm FB Connectors 114-1075 C. Guides The pin headers have alignment slots with a guide-in that helps position the pin and socket contacts prior to engagement of the circuits. See Figure 1. D. End-to-End Placement The end contacts in the pin header and receptacle are one half the contact spacing distance from the ends of the housing. This design feature makes it possible to mount connectors end-to-end while maintaining the 2 mm grid pattern. When making this type of application, note that the contacts in the pin header are closer to one side of the housing to allow space for the mating pc board. The contacts and board slots must be aligned with each other when mating with a continuous pc board connector. Connectors can be mounted end-to-end within the specified dimension. See Figure 3. 1 mm 1 mm Joining Ends 2 mm 2 mm Pin Header Connectors Receptacle Connectors NOTE: 4-row shown, 5-row is the same for dimensioning purposes. Figure 3 3.3. Alignment Proper alignment is essential to ensure full engagement of mating connectors, and to ensure that contacts are not bent or otherwise damaged during mating and unmating. For tolerance limitations, see Figure 4. NOTE: 4-row shown, 5-row is the same for dimensioning purposes. _ +2 _ +2 Receptacle 2.5 2.5 1.5 (2 Places) Pin Header 9.2 (Min) PC Board (Typ) Figure 4 Rev D Tyco Electronics Corporation 5 of 15 Z-PACK 2mm FB Connectors 114-1075 3.4. Mating Dimension Full mating of connectors is necessary to ensure a good connection. The dimension from the surface of the pc board to which the pin header is mounted and the first row of contacts in the receptacle must be as shown in Figure 5. Right Angle-to-Vertical PC Board Standoff PC Board 1.50 Retention Post 10.00 Right Angle-to-Right Angle 1.50 PC Board 11.00 Retention Posts PC Board NOTE: 4-row shown, 5-row is the same for dimensioning purposes. Figure 5 3.5. PC Board Requirements A. PC Board Thickness Right-angle receptacle and right-angle pin header connectors with compliant pins require a pc board with a minimum thickness of 1.30 mm. Those with solder tines will accommodate any pc board thickness that allows the tine to protrude a minimum of 1.00 mm from the bottom surface of the pc board. Vertical pin header connectors with compliant pin contacts require a pc board with a minimum thickness of 2.40 mm. Pin header connectors with solder tines will accommodate any pc board thickness that allows the solder tines to protrude a minimum of 1.00 mm from the bottom surface of the pc board. Mating pc boards for pin header connectors require a maximum allowable thickness of 2.50 mm. B. PC Board Circuit Pattern Layout The pc board layout patterns for the placement of Z-PACK 2mm FB Pin Header and Receptacle Connectors are provided in Figure 6. NOTE For applications requiring the minimum installation force for the connector, the pc board through-hole size should favor the high end of the allowable tolerance. For applications using IR or vapor phase soldering techniques in conjunction i 6 of 15 with solder paste, through-hole size should favor the low end of the allowable tolerance to ensure optimum solder fill. Tyco Electronics Corporation Rev D Z-PACK 2mm FB Connectors NOTE: 114-1075 Vertical connector pc board layouts are the same for both solder type and press fit except press fit does not have guide post holes. Right-angle connector pc board layouts are the same for both solder type and press-fit. Recommended 4-Row PC Board Circuit Pattern Vertical Connectors Layouts (Component Side) Right-Angle Connectors Recommended 5-Row PC Board Circuit Pattern Vertical Connectors Layouts (Component Side) Right-Angle Connectors Figure 6 (cont'd) Rev D Tyco Electronics Corporation 7 of 15 Z-PACK 2mm FB Connectors NOTE: 114-1075 Vertical connector pc board layouts are the same for both solder type and press fit except press fit does not have guide post holes. Right-angle connector pc board layouts are the same for both solder type and press-fit. Recommended 4-Row PC Board Circuit Pattern Vertical Power Module Connectors Layouts (Component Side) Right-Angle Power Module Connectors Recommended 5-Row PC Board Circuit Pattern Layouts (Component Side) Vertical Power Module Connectors Right-Angle Power Module Connectors Figure 6 (cont'd) 8 of 15 Tyco Electronics Corporation Rev D Z-PACK 2mm FB Connectors 114-1075 NUMBER OF SIGNAL POSITIONS DIMENSION B DIMENSION C 630 125 250 540 107 214 264 330 65 130 240 300 59 118 216 270 53 106 192 240 47 94 168 210 41 82 144 180 35 70 120 150 29 58 96 120 23 46 72 90 17 34 48 60 11 22 24 30 5 10 4-ROW 5-ROW --- Figure 6 (end) C. Contact Hole Configuration The contact holes in the pc board for all connectors must be prepared to the dimensions specified in Figure 7. 0.65-0.80 (Ref) EEEEE EEEEE II II EEEEE II II EEEEE II II EEEEE II II EEEEE II II EEEEE II II I I EEEEE I I EEEEE I I EEEEE I I EEEEE I I EEEEE I EEEEE I EEEEE Diameter of Finished Hole After Plating 0.81-0.86 Drilled Hole Diameter 1.12 Min Pad Diameter FR-4 Material PC Board Thickness (See Paragraph 3.5) 0.025-0.050 Copper Plating Surface Finish (See Table Below) SURFACE FINISH THICKNESS PLATING 0.004-0.010 Hot Air Solder Leveling (HASL) Tin-Lead (Sn Pb) 0.0005-0.004 Immersion Tin (Sn) 0.0002-0.0005 Organic Solderability Preservative (OSP) 0.0001-0.0005 Au, 0.00127-0.0076 Ni 0.0001-0.0005 Immersion Gold (Au) Over Nickel (Ni) (ENIG) Immersion Silver (Ag) Figure 7 Rev D Tyco Electronics Corporation 9 of 15 Z-PACK 2mm FB Connectors 114-1075 3.6. Special Handling A. Initial Positioning Prior to positioning a connector, the pc board should be placed on an appropriate board support fixture. Connectors should be gripped by the housing only and not by the contacts. When placing a connector into a pc board, all contact pins should be aligned and inserted into the pc board simultaneously to prevent twisting or bending of the contacts. If using robotic equipment, a total equipment accuracy of +0.13 mm, including the gripper and fixture tolerance and equipment repeatability, is required. B. Seating Connectors Seating force must be applied evenly on the connectors to prevent deformation or other damage to the contacts and housings. The standoffs must be within 0.13 mm of the pc board (after insertion or soldering). Refer to Paragraph 3.8. When installing vertical pin header connectors with compliant pins, the insertion force must be simultaneously applied to the shoulder of each contact on the inside floor surface of the connector. When installing right-angle connectors with compliant contact pins, the insertion force must be evenly applied to the back/top surface of the connector housing (see Figure 1) with a force of approximately 67 N per pin. When installing vertical pin header connectors with solder tines, the insertion force must be evenly distributed to the inside floor surface of the connector. When installing right-angle connectors with solder tines, the insertion force must be evenly applied to the back/top surface of the connector housing (See Figure 1) with a force of approximately 40 N per each 12 mm of length of the connector. Connectors will remain securely on the pc board until passed through soldering providing that they are not jarred in any manner. Tooling recommendations are covered in Section 5. 3.7. Soldering Connectors with solder tines must be soldered to the pc board. A. Flux Selection The solder tines must be fluxed prior to soldering with a rosin base flux. Selection of the proper flux will depend on the type of pc board and other components mounted on the pc board. The flux must be compatible with the wave solder line, and all manufacturing and safety requirements. DANGER To avoid personal injury, strict attention must be given to the recommendations of the solvent manufacturer regarding toxicity and other safety requirements. Request the Material Safety Data Sheet (MSDS) from the supplier. B. Cleaning After soldering, removal of fluxes, residues, and activators is necessary. Consult with the supplier of the solder and flux for recommended cleaning solvents. A list of common cleaning solvents that will not affect the connectors for the time and temperature specified is provided in Figure 8. CLEANER TIME TEMPERATURES (Max) TYPE (Minutes) ALPHA 2110 Aqueous 1 132 270 BIOACT EC-7 Solvent 5 100 212 CARBITOL Solvent 1 Isopropyl Alcohol Solvent 5 100 212 KESTER 5778 Aqueous 5 100 212 KESTER 5779 Aqueous 5 100 212 LONCOTERGE 520 Aqueous 5 100 212 LONCOTERGE 530 Aqueous 5 100 212 Terpene Solvent Solvent 5 100 212 NAME CELSIUS FAHRENHEIT Room Ambience Figure 8 C. Drying When drying cleaned assemblies and pc boards, do not exceed the temperature limitations of -55_ to 125_C [-99_ to 225_F]. Excessive temperatures may cause housing degradation. 10 of 15 Tyco Electronics Corporation Rev D Z-PACK 2mm FB Connectors 114-1075 D. Soldering Guidelines Refer to Paragraph 2.4 for reference Manual 402-40 that is available for establishing soldering guidelines. 3.8. Inspection A. Solder Fillets All solder fillets should comply to the Workmanship Standard 101-21. For a typical fillet for these connectors, refer to Figure 9. B. Housing Stand-Offs The connector housing standoffs must be seated within the dimension shown in Figure 9 of the pc board (after insertion or soldering). Vertical Pin Header Type Connector Right-Angle Type Connector Typical Solder Fillet Flush to Flush to Within 0.13 Within 0.13 NOTE: 4-row shown, 5-row is the same for dimensioning purposes. Figure 9 3.9. Repair Damaged contacts can not be removed from receptacle housing connectors. The entire connector will have to be removed and replaced with a new one. A. Right-Angle Receptacles with Solder Tines Before removing the connectors from the pc board, remove solder from all solder tines by heating them and removing the solder fillet. Do NOT apply heat to the pc board, otherwise you could damage plated-through holes. After solder is removed, grip the center of the housing with a pair of pliers and pull the connector straight away from the pc board. Drill the holes with a 0.60 mm drill bit; then clean the holes. Insert a new connector and solder it using standard hand soldering technique. See Figure 10. Pliers PC Board Retention Post (Plastic Material) Rev D Figure 10 Tyco Electronics Corporation 11 of 15 Z-PACK 2mm FB Connectors 114-1075 B. Right-Angle Connectors with Compliant Pins Place the connector in a housing support that has a slot wide enough and deep enough to receive the full length of the housing and contacts. Make sure the tool support will not interfere with any other components on the pc board. Apply an even force simultaneously to all compliant pins with a push bar and press capable of applying 100 N per pin. See Figure 11. Force Push Bar Open Space Housing Support Force Force Force Push Bar Housing Support Open Space Figure 11 C. Vertical Pin Headers with Solder Tines Individual solder tine contacts can be removed by removing the solder fillet and gripping the front of the contact with a pair of needle-nosed pliers and pulling it straight out the front of the pin header. Replace contact with a new one. D. Vertical Pin Headers with Compliant Pins Individual compliant pin connector contacts can be removed and replaced with a new one without removing the pin header module from the pc board. If the pin header housing is damaged, the entire connector must be removed and replaced with a new one. In either case, the pc board must be firmly supported while in-line force is applied on the contact pin. Replace contact with a new one. See Section 5 for recommended impact repair tool. 4. QUALIFICATION These connectors meet Institute of Electrical and Electronic Engineers (IEEE), Electronic Industries Association (EIA), and International Electrotechnical Commission (IEC) specifications for printed circuit boards. Z-PACK 2mm FB Connectors are Component Recognized by Underwriters Laboratories Inc. (UL) in File E28476 and Certified by CSA International in File No. LR7189. 12 of 15 Tyco Electronics Corporation Rev D Z-PACK 2mm FB Connectors 114-1075 5. TOOLING Tyco Electronics has existing tooling and tooling concepts for applying these connectors. Part numbers of available tools and the applicable instructional material for each is provided in Figure 12. S Robotic Equipment Robotic equipment for placement of connectors on a pc board must have a true position accuracy of 0.13 mm to ensure proper location and insertion of the contact pins. This includes gripper and fixture tolerances as well as equipment repeatability. It must use the connector datum surface to ensure reliable connector placement. If you need assistance in setting up prototype or production line equipment, contact Tooling Engineering through your local Tyco Electronics Representative or call the Tooling Assistance Center number at the bottom of page 1. S Seating Tool Seating tools are designed to push evenly on the shoulders of the vertical pin contact and force the compliant pins into the pc board. See Figure 1. S Push Bar Commercially available bar stock with a flat surface large enough to cover the top surface of right-angle connectors and capable of exerting 67 N per pin can be used as a push bar to seat the compliant pin and solder tine connectors onto the pc board. The same type tooling can be used to remove damaged right-angle connectors from a pc board by pressing evenly on the compliant end of the contacts. S PC Board Support A pc board support must be used to prevent bowing of the pc board during insertion of the connectors. It should have a flat surface with holes or a channel large enough to receive the pins during installation. S Housing Support A housing support with sides and ends as close as possible to the receptacle housing is recommended for removing damaged receptacle connectors from pc boards. S Repair Tool A repair tool kit consisting of a spring-loaded impact tool handle assembly, a removal tip, and a replacement tip is available for removing damaged compliant pin contacts and replacing them with new ones. The housing must be supported and the contact must be free to back out of housing with a suitable housing support that will not damage housing. NOTE The tooling referenced in Figure 12 may be used for both compliant pin and solder type connectors. i PC Board Support Fixture (Customer Supplied) Typical Seating Tool (See Table) PC Board Support Fixture 679980-1 or -2 With Bottom Support Anvil 679977-1 or -2 (408-4038) H-Frame Power Unit 803880-6 Figure 12 (cont'd) Rev D Tyco Electronics Corporation 13 of 15 Z-PACK 2mm FB Connectors 114-1075 Robotic Equipment Push Bar (Typ) (Customer Supplied) Pin Repair Kit 354687-1 (For Removing and Replacing Damaged Housing Support Contacts (408-9979) (4-ROW) CONN MODULE O TYPE Signal (Customer Supplied) POSN (5-ROW) SEATING TOOL POWER UNIT (DOCUMENT) (DOCUMENT) POSN SEATING TOOL (DOCUMENT) 24 58511-1 (408-9910) 30 318860-1 (408-4250) 48 58511-2 (408-9910) 60 318860-2 (408-4250) 72 1-58511-4 (408-9910) 90 318860-3 (408-4250) 96 58511-3 (408-9910) 120 318860-4 (408-4250) 120 58511-6 (408-9910) 150 318860-5 (408-4250) 144 58511-5 (408-9910) 180 318860-6 (408-4250) 210 318860-7 (408-4250) 803880-6 (409-5567) 168 58511-7 (408-9910) 192 58511-4 (408-9910) 240 318860-8 (408-4250) 216 58511-8 (408-9910) 270 318860-9 (408-4250) 240 58511-9 (408-9910) 300 1-318860-0 (408-4250) 330 1-318860-1 (408-4250) 540 1-318860-3 (408-4250) 630 1-318860-2 (408-4250) ) (409-5626) 814700-2 ( POWER UNIT 803880-6 264 1-58511-0 (408-9910) 8 58512-1 (408-4157) 16 58512-2 (408-4157) Power Hybrid y S Signal/ / Power Mix 8P-96S 1-58511-7 (408-9910) 8P-120S 1-58511-8 (408-9910) 8P-144S 1-58511-3 (408-9910) 8P-192S 1-58511-1 (408-9910) 8P-216S 1-58511-2 (408-9910) 16P-192S 1-58511-6 (408-9910) 16P-216S 1-58511-5 (408-9910) 803880-6 (409-5567) ( ) 10 814700-2 (409-5626) 803880-6 (409-5567) ) 814700-2 ( (409-5626) 10P-30S 1214224-1 (408-4488) 1-318860-4 (408-4250) Figure 12 (end) 14 of 15 Tyco Electronics Corporation Rev D Z-PACK 2mm FB Connectors 114-1075 6. VISUAL AID Figure 13 shows a typical application of Z-PACK 2mm FB Connectors. This illustration should be used by production personnel to ensure a correctly applied product. Applications which DO NOT appear correct should be inspected using the information in the preceding pages of this specification and in the instructional material shipped with the product or tooling. OVERALL LENGTH OF PIN HEADERS AND RECEPTACLES MUST BE THE SAME CONNECTOR CONTACTS MUST BE IDENTICAL HOUSING MUST (SIGNAL TO SIGNAL AND BE SEATED POWER TO POWER) ON PC BOARD WIDEST SECTION OF COMPLIANT PIN MUST BE INSIDE PC BOARD HOLE MATING CONNECTORS (SIGNAL OR POWER) MUST MATCH PINS MUST NOT BE BENT SOLDER FILLETS MUST BE _ AROUND SOLDER TINES 360 WITH NO SKIPS OR VOIDS FIGURE 13. VISUAL AID Rev D Tyco Electronics Corporation 15 of 15