ESM_englisch_03_2009:Axial_D 09.03.2009 14:40 Seite 1 Energy-saving axial fans The engineer's choice version 03/2009 ESM_englisch_03_2009:Axial_D 09.03.2009 14:40 Seite 2 New energy-saving axial fans The new generation of compact energy-saving axial fans In almost all spheres of life, energy savings have become an important issue by now. Our new and compact axial fans are based on the energy-saving motor (ESM) and offer high efficiency and thus considerable energy savings and improved service life at the same time - aspects which are definitely called for with refrigeration plants, such as refrigerated display cases or refrigeration chests or condensing units. The axial fan W1G 200 already established quite successfully on the market has now been complemented by the sizes 172, 230, 250 and 300 mm. The new plastic rotor was optimised to meet improved aerodynamic criteria and makes these fans operate even more quietly. What is more, they environment benefits from the fact that no varnish needs to be used any more! Compared to conventional shaded pole motors, energy-saving motors are three times as efficient. Higher efficiency translates into less intrinsic heat generated during operation, with a reduced need to dissipate heat and putting a strain on the environment. This results in further energy savings, as less refrigeration capacity has to be applied in the first instance. The new and compact energy-saving axial fans, with an output power of between 5 and 20 W, can be easily connected via a plug-in connection. Moreover, the motor speed can be optionally set via programming interface. A second speed step - e.g. for night setback, can be realised via actuator input. The energy-saving fans are robust, maintenance-free and durable. Their service life is rated at more than 40,000 hours, equalling continuous operation of more than 4.5 years. As regards environmental impacts, their design complies with protection type IP 54 specifications. Optionally, protection type IP 65 is available. Moreover, these energy-saving axial fans comply with protection class 2. 2 ESM_englisch_03_2009:Axial_D 09.03.2009 14:40 Seite 3 Table of content New energy-saving axial fans 2 Size 172 4 Size 200 6 Size 230 12 Size 250 14 Size 300 16 Connection leads 20 ebm-papst representatives & subsidiaries 22 3 ESM_englisch_03_2009:Axial_D 09.03.2009 14:40 Seite 4 Energy-saving axial fans O 172 - Material: Wall ring: Plastic PP Blade: Plastic PA - Number of blades: 5 - Direction of air flow: "V", exhaust over struts - Direction of rotation: Counter-clockwise seen on rotor - Type of protection: IP 54 - Insulation class: "B" - Mounting position: Any - Condensate discharges: None Nominal voltage Frequency Speed (1) Max. Power input (1) Max. Current draw (1) Max. operative range Perm. amb. temp. Mass Type Motor W1G172-EC95 -01 M1G 055-BD W1G172-EC91 -01 M1G 055-BD subject to alterations Mode of operation: Continuous operation (S1) Bearings: Maintenance-free ball bearings Motor protection: Via electronics and TOP Electrical connection: Line cord with plug Protection class: II Product conforming to standard: CE Approvals: VDE; UL, CSA is applied for - Speed: Using the programming unit, 2 speeds between nmin and nmax can be programmed. VAC Hz rpm W A Pa C kg A 115 50/60 2400 22 0,34 55 -30..+50 0,95 B 230 50/60 2400 22 0,17 55 -30..+50 0,95 Curve Nominal data - - - - - - - (1) Nominal data in operating point with maximum load and 115 or 230 VAC 2 [Pa] A B 0,24 60 [in H O] Curves 0,16 40 0,20 4 50 0,12 8 0,08 20 2 10 0,04 7 6 5 0 50 50 100 100 n max. = 2400 min-1 4 150 150 200 250 n = 1500 min-1 200 300 350 1 [CFM] 250 400 n min. = 900 min-1 450 [m3/h] P1 [W] I [A] LpA [dB(A)] A 1 2400 19 0,30 53 A 2 2400 21 0,32 53 A 3 2400 22 0,34 53 A 4 2400 22 0,34 53 A 5 1500 8 0,12 42 A 6 1500 8 0,14 43 A 7 1500 9 0,14 43 A 8 1500 9 0,14 44 B 1 2400 19 0,15 53 B 2 2400 21 0,16 53 B 3 2400 22 0,17 53 B 4 2400 22 0,17 53 B 5 1500 8 0,06 42 B 6 1500 8 0,07 43 B 7 1500 9 0,07 43 B 8 1500 9 0,07 44 3 30 n [rpm] ESM_englisch_03_2009:Axial_D 09.03.2009 14:40 Seite 5 - Electr. connection: Power system: 115 or 230 VAC, 50/60 Hz black L1 1 blue N 2 Speed selection brown Energysaving motor (ESM) 5 115 or 230 VAC L or N 78.5 4x O4.3 "V" O222 O208 6 4 405 450+20 O172 O19 2 35 5 Connection lead p. 20 ESM_englisch_03_2009:Axial_D 09.03.2009 14:40 Seite 6 Energy-saving axial fans O 200 - Material: Wall ring: Plastic PP Blade: Plastic PA - Number of blades: 5 - Direction of air flow: "V", exhaust over struts - Direction of rotation: Counter-clockwise seen on rotor - Type of protection: IP 54 - Insulation class: "B" - Mounting position: Any - Condensate discharges: None Nominal voltage Frequency Speed (1) Max. Power input (1) Max. Current draw (1) Max. operative range Perm. amb. temp. Mass Type Motor W1G200-EC91 -27 M1G 055-BD W1G200-EC87 -25 M1G 055-BD subject to alterations Mode of operation: Continuous operation (S1) Bearings: Maintenance-free ball bearings Motor protection: Via electronics and TOP Electrical connection: Line cord with plug Protection class: II Product conforming to standard: CE Approvals: VDE; UL, CSA is applied for - Speed: Using the programming unit, 2 speeds between nmin and nmax can be programmed. VAC Hz rpm W A Pa C kg A 115 50/60 1300 8,0 0,11 24 -30..+50 1,0 B 230 50/60 1300 8,5 0,07 24 -30..+50 1,0 Curve Nominal data - - - - - - - (1) Nominal data in operating point with maximum load and 115 or 230 VAC [in H O] [Pa] Curves 2 A 0,10 25 B n [rpm] P1 [W] I [A] LpA [dB(A)] A 1 1300 7 0,09 42 A 2 1300 8 0,10 41 A 3 1300 8 0,10 41 A 4 1300 8 0,11 42 A 5 900 3 0,05 33 A 6 900 4 0,05 32 A 7 900 4 0,05 32 A 8 900 4 0,05 33 B 1 1300 7 0,06 42 B 2 1300 8 0,07 41 B 3 1300 8,5 0,07 41 B 4 1300 8,5 0,07 42 B 5 900 3 0,03 33 B 6 900 4 0,04 32 B 7 900 4 0,04 32 B 8 900 4 0,04 33 20 0,08 4 15 0,06 3 0,04 8 10 2 5 0,02 7 6 5 0 50 100 n max. = 1300 min-1 6 100 150 200 n = 900 min-1 1 200 300 250 400 n min. = 500 min-1 [CFM] [m3/h] ESM_englisch_03_2009:Axial_D 09.03.2009 14:40 Seite 7 - Electr. connection: Power system: 115 or 230 VAC, 50/60 Hz black L1 1 blue N 2 Speed selection brown Energysaving motor (ESM) 5 115 or 230 VAC L or N 78.5 4x O4.3 O250 O236 6 4 405 450+20 O200 O22 0 40 "V" 7 Connection lead p. 20 ESM_englisch_03_2009:Axial_D 09.03.2009 14:41 Seite 8 Energy-saving axial fans O 200 - Material: Wall ring: Plastic PP Blade: Plastic PA - Number of blades: 5 - Direction of air flow: "V", exhaust over struts - Direction of rotation: Counter-clockwise seen on rotor - Type of protection: IP 54 - Insulation class: "B" - Mounting position: Any - Condensate discharges: None Nominal voltage Frequency Speed (1) Max. Power input (1) Max. Current draw (1) Max. operative range Perm. amb. temp. Mass Type Motor W1G200-EC95 -47 M1G 055-BD W1G200-EC91 -45 M1G 055-BD subject to alterations Mode of operation: Continuous operation (S1) Bearings: Maintenance-free ball bearings Motor protection: Via electronics and TOP Electrical connection: Line cord with plug Protection class: II Product conforming to standard: CE Approvals: VDE; UL, CSA is applied for - Speed: Using the programming unit, 2 speeds between nmin and nmax can be programmed. VAC Hz rpm W A Pa C kg A 115 50/60 2100 31 0,48 55 -30..+50 1,0 B 230 50/60 2100 31 0,24 55 -30..+50 1,0 Curve Nominal data - - - - - - - (1) Nominal data in operating point with maximum load and 115 or 230 VAC 2 [Pa] A B 0,24 60 [in H O] Curves 20 10 0,16 0,12 30 6 0 50 100 100 n max. = 2100 min-1 8 2 150 200 200 300 250 400 n = 1500 min-1 5 300 500 350 600 n min. = 800 min-1 400 700 1 [CFM] [m3/h] I [A] LpA [dB(A)] 1 2100 29 0,44 55 A 2 2100 30 0,46 54 A 3 2100 31 0,48 53 A 4 2100 31 0,48 55 A 5 1500 14 0,22 46 A 6 1500 16 0,24 45 A 7 1500 16 0,26 45 A 8 1500 16 0,26 46 B 1 2100 29 0,22 55 B 2 2100 30 0,23 54 B 3 2100 31 0,24 53 B 4 2100 31 0,24 55 B 5 1500 14 0,11 46 B 6 1500 16 0,12 45 B 7 1500 16 0,13 45 B 8 1500 16 0,13 46 8 7 P1 [W] A 3 0,08 40 0,04 50 0,20 4 n [rpm] ESM_englisch_03_2009:Axial_D 09.03.2009 14:41 Seite 9 - Electr. connection: Power system: 115 or 230 VAC, 50/60 Hz black L1 1 blue N 2 Speed selection brown Energysaving motor (ESM) 5 115 or 230 VAC L or N 78.5 4x O4.3 O250 O236 6 4 405 450+20 O200 O22 0 40 "V" 9 Connection lead p. 20 ESM_englisch_03_2009:Axial_D 09.03.2009 14:41 Seite 10 Energy-saving axial fans O 200 - Material: Blade: Plastic PA Guard grille: Plastic PP - Number of blades: 5 - Direction of air flow: "A", intake over guard grille - Direction of rotation: Counter-clockwise seen on rotor - Type of protection: IP 54 - Insulation class: "B" - Mounting position: Any - Condensate discharges: None Nominal voltage Frequency Speed (1) Max. Power input (1) Max. Current draw (1) Max. operative range Perm. amb. temp. Mass Type Motor S1G 200-CA95 -02 M1G 055-BD S1G 200-CA91 -02 M1G 055-BD subject to alterations Hz rpm W A Pa C kg A 115 50/60 2000 31 0,43 45 -30..+50 0,95 B 230 50/60 2000 33,5 0,25 45 -30..+50 0,95 (1) Nominal data in operating point with maximum load and 115 or 230 VAC 2 A B 0,20 [Pa] [in H O] Curves 50 0,12 30 0,16 4 40 3 0,08 8 20 7 0,04 6 5 0 50 100 100 n max. = 2000 min-1 10 150 200 200 300 250 400 n = 1500 min-1 300 500 1 350 600 n min. = 800 min-1 400 700 [CFM] [m3/h] n [rpm] P1 [W] I [A] LpA [dB(A)] A 1 2000 30 0,43 54 A 2 2000 30 0,43 54 A 3 2000 30 0,43 53 A 4 2000 31 0,43 54 A 5 1500 17 0,29 50 A 6 1500 18 0,29 50 A 7 1500 19 0,29 49 A 8 1500 20 0,29 50 B 1 2000 32 0,24 54 B 2 2000 33 0,25 54 B 3 2000 33 0,25 53 B 4 2000 33,5 0,25 54 B 5 1500 18 0,16 50 B 6 1500 19 0,16 50 B 7 1500 19 0,16 49 B 8 1500 20 0,16 50 2 10 Mode of operation: Continuous operation (S1) Bearings: Maintenance-free ball bearings Motor protection: Via electronics and TOP Electrical connection: Line cord with plug Protection class: II Product conforming to standard: CE Approvals: VDE; UL, CSA is applied for Speed: Using the programming unit, 2 speeds between nmin and nmax can be programmed. VAC Curve Nominal data - - - - - - - - ESM_englisch_03_2009:Axial_D 09.03.2009 14:41 Seite 11 - Electr. connection: Power system: 115 or 230 VAC, 50/60 Hz black L1 1 blue N 2 Speed selection brown Energysaving motor (ESM) 5 115 or 230 VAC L or N 38.5 3 4x O6.5 "A" 6 37.5 405 450+20 O260 O278 O200 40 11 Connection lead p. 20 ESM_englisch_03_2009:Axial_D 09.03.2009 14:41 Seite 12 Energy-saving axial fans O 230 - Material: Wall ring: Plastic PP Blade: Plastic PA - Number of blades: 5 - Direction of air flow: "V", exhaust over struts - Direction of rotation: Counter-clockwise seen on rotor - Type of protection: IP 54 - Insulation class: "B" - Mounting position: Any - Condensate discharges: None Nominal voltage Frequency Speed (1) Max. Power input (1) Max. Current draw (1) Max. operative range Perm. amb. temp. Mass Type Motor W1G230-EB97 -01 M1G 055-BD W1G230-EB89 -01 M1G 055-BD subject to alterations Mode of operation: Continuous operation (S1) Bearings: Maintenance-free ball bearings Motor protection: Via electronics and TOP Electrical connection: Line cord with plug Protection class: II Product conforming to standard: CE Approvals: VDE; UL, CSA is applied for - Speed: Using the programming unit, 2 speeds between nmin and nmax can be programmed. VAC Hz rpm W A Pa C kg A 115 50/60 1500 23 0,35 38 -30..+50 1,05 B 230 50/60 1500 26 0,20 38 -30..+50 1,05 Curve Nominal data - - - - - - - (1) Nominal data in operating point with maximum load and 115 or 230 VAC 2 0,16 [Pa] 20 B 4 0,12 30 A 3 0,08 40 [in H O] Curves 8 0,04 10 6 5 0 100 200 n max. = 1500 min-1 12 200 300 400 n = 1000 min-1 400 600 500 800 n min. = 700 min-1 1 [CFM] [m3/h] P1 [W] I [A] LpA [dB(A)] A 1 1500 23 0,35 51 A 2 1500 23 0,35 51 A 3 1500 23 0,35 50 A 4 1500 23 0,35 50 A 5 1000 9 0,15 39 A 6 1000 10 0,16 39 A 7 1000 10 0,16 40 A 8 1000 10 0,16 40 B 1 1500 24 0,19 51 B 2 1500 25 0,19 51 B 3 1500 25 0,19 50 B 4 1500 26 0,20 50 B 5 1000 10 0,09 39 B 6 1000 11 0,09 39 B 7 1000 11 0,09 40 B 8 1000 11 0,09 40 2 7 n [rpm] ESM_englisch_03_2009:Axial_D 09.03.2009 14:41 Seite 13 - Electr. connection: Power system: 115 or 230 VAC, 50/60 Hz black L1 1 blue N 2 Speed selection brown Energysaving motor (ESM) 5 115 or 230 VAC L or N 78.5 4x O4.3 O280 O266 6 4 405 450+20 O230 O25 0 50 "V" 13 Connection lead p. 20 ESM_englisch_03_2009:Axial_D 09.03.2009 14:41 Seite 14 Energy-saving axial fans O 250 - Material: Wall ring: Plastic PP Blade: Plastic PA - Number of blades: 5 - Direction of air flow: "V", exhaust over struts - Direction of rotation: Counter-clockwise seen on rotor - Type of protection: IP 54 - Insulation class: "B" - Mounting position: Any - Condensate discharges: None Nominal voltage Frequency Speed (1) Max. Power input (1) Max. Current draw (1) Max. operative range Perm. amb. temp. Mass Type Motor W1G250-BB21 -01 M1G 055-BI W1G250-BB17 -01 M1G 055-BI subject to alterations Hz rpm W A Pa C kg A 115 50/60 1700 32 0,47 42 -30..+50 1,55 B 230 50/60 1700 32 0,24 42 -30..+50 1,55 (1) Nominal data in operating point with maximum load and 115 or 230 VAC A 2 [Pa] [in H O] Curves B 0,16 0,12 30 3 20 0,08 8 7 0,04 6 5 0 100 200 n max. = 1700 min-1 14 200 300 400 400 600 n = 1200 min-1 500 800 n min. = 900 min-1 1 [CFM] 1000 [m /h] 3 P1 [W] I [A] LpA [dB(A)] 1 1700 30 0,44 55 A 2 1700 31 0,45 56 A 3 1700 32 0,47 56 A 4 1700 32 0,47 57 A 5 1200 14 0,22 46 A 6 1200 15 0,24 46 A 7 1200 16 0,25 47 A 8 1200 17 0,26 48 B 1 1700 30 0,24 55 B 2 1700 31 0,24 56 B 3 1700 32 0,24 56 B 4 1700 32 0,24 57 B 5 1200 14 0,12 46 B 6 1200 15 0,13 46 B 7 1200 16 0,14 47 B 8 1200 17 0,14 48 2 10 n [rpm] A 4 40 Mode of operation: Continuous operation (S1) Bearings: Maintenance-free ball bearings Motor protection: Via electronics and TOP Electrical connection: Line cord with plug Protection class: II Product conforming to standard: CE Approvals: VDE, UL, CSA is applied for Speed: Using the programming unit, 2 speeds between nmin and nmax can be programmed. VAC Curve Nominal data - - - - - - - - ESM_englisch_03_2009:Axial_D 09.03.2009 14:41 Seite 15 - Electr. connection: Power system: 115 or 230 VAC, 50/60 Hz black L1 1 blue N 2 Speed selection Energysaving motor (ESM) 5 brown 115 or 230 VAC L or N 296 4x90 92 80 4 O280 O250 4xO7 45 95 O2 315 O 405 6 "V" 450+20 15 Connection lead p. 20 ESM_englisch_03_2009:Axial_D 09.03.2009 14:41 Seite 16 Energy-saving axial fans O 300 - Material: Wall ring: Plastic PP Blade: Plastic PA - Number of blades: 5 - Direction of air flow: "V", exhaust over struts - Direction of rotation: Counter-clockwise seen on rotor - Type of protection: IP 54 - Insulation class: "B" - Mounting position: Any - Condensate discharges: None Nominal voltage Frequency Speed (1) Max. Power input (1) Max. Current draw (1) Max. operative range Perm. amb. temp. Mass Type Motor W1G300-BB23 -01 M1G 055-BI W1G300 -BB19 -01 M1G 055-BI subject to alterations Hz rpm W A Pa C kg A 115 50/60 1300 35 0,50 35 -30..+50 1,75 B 230 50/60 1300 35 0,27 35 -30..+50 1,75 (1) Nominal data in operating point with maximum load and 115 or 230 VAC A 2 [Pa] 0,14 [in H O] Curves 30 B 4 0,12 35 0,08 20 0,10 3 25 Mode of operation: Continuous operation (S1) Bearings: Maintenance-free ball bearings Motor protection: Via electronics and TOP Electrical connection: Line cord with plug Protection class: II Product conforming to standard: CE Approvals: VDE, UL, CSA is applied for Speed: Using the programming unit, 2 speeds between nmin and nmax can be programmed. VAC Curve Nominal data - - - - - - - - n [rpm] P1 [W] I [A] LpA [dB(A)] A 1 1300 28 0,41 52 A 2 1300 31 0,46 52 A 3 1300 32 0,47 51 A 4 1300 35 0,50 52 A 5 900 12 0,24 43 A 6 900 14 0,26 42 A 7 900 15 0,28 42 A 8 900 16 0,30 43 B 1 1300 32 0,25 52 B 2 1300 34 0,27 52 B 3 1300 34 0,27 51 B 4 1300 35 0,27 52 B 5 900 13 0,12 43 B 6 900 14 0,13 42 B 7 900 15 0,14 42 B 8 900 16 0,15 43 0,06 8 15 2 10 0,04 7 5 0,02 6 5 0 100 200 200 n max. = 1300 min-1 16 300 400 400 600 500 800 n = 900 min-1 600 1000 700 1200 n min. = 700 min-1 1 800 [CFM] [m3/h] ESM_englisch_03_2009:Axial_D 09.03.2009 14:41 Seite 17 - Electr. connection: Power system: 115 or 230 VAC, 50/60 Hz black L1 1 blue N 2 Speed selection Energysaving motor (ESM) 5 brown 115 or 230 VAC L or N 92 80 4 45 O350 O300 4xO6.3 360 4x90 80 O3 397 O "V" 405 6 +20 450 17 Connection lead p. 20 ESM_englisch_03_2009:Axial_D 09.03.2009 14:41 Seite 18 Energy-saving axial fans O 300 - Material: Blade: Plastic PA Guard grille: Plastic PP - Number of blades: 5 - Direction of air flow: "A", intake over guard grille - Direction of rotation: Counter-clockwise seen on rotor - Type of protection: IP 54 - Insulation class: "B" - Mounting position: Any - Condensate discharges: None Nominal voltage Frequency Speed (1) Max. Power input (1) Max. Current draw (1) Max. operative range Perm. amb. temp. Mass Type Motor S1G 300-CA23 -02 M1G 055-BI S1G 300-CA19 -02 M1G 055-BI subject to alterations Hz rpm W A Pa C kg A 115 50/60 1200 35 0,56 40 -30..+50 1,4 B 230 50/60 1200 35 0,28 40 -30..+50 1,4 (1) Nominal data in operating point with maximum load and 115 or 230 VAC 2 B 0,16 [Pa] A 0,08 7 6 0 100 200 n max. = 1200 min-1 18 I [A] LpA [dB(A)] 1 1200 24 0,40 54 A 2 1200 27 0,44 53 A 3 1200 31 0,50 54 A 4 1200 35 0,56 54 A 5 900 16 0,30 51 A 6 900 18 0,34 50 A 7 900 19 0,36 49 A 8 900 21 0,40 49 B 1 1200 24 0,20 54 B 2 1200 27 0,22 53 B 3 1200 31 0,25 54 B 4 1200 35 0,28 54 B 5 900 16 0,15 51 B 6 900 18 0,17 50 B 7 900 19 0,18 49 B 8 900 21 0,20 49 2 0,04 10 P1 [W] 3 8 20 n [rpm] A 4 0,12 30 [in H O] Curves 40 Mode of operation: Continuous operation (S1) Bearings: Maintenance-free ball bearings Motor protection: Via electronics and TOP Electrical connection: Line cord with plug Protection class: II Product conforming to standard: CE Approvals: VDE, UL, CSA is applied for Speed: Using the programming unit, 2 speeds between nmin and nmax can be programmed. VAC Curve Nominal data - - - - - - - - 200 300 400 5 500 400 600 n = 900 min-1 800 n min. = 700 min-1 600 1 [CFM] 1000 [m3/h] ESM_englisch_03_2009:Axial_D 09.03.2009 14:42 Seite 19 - Electr. connection: Power system: 115 or 230 VAC, 50/60 Hz black L1 1 blue N 2 Speed selection brown Energysaving motor (ESM) 5 115 or 230 VAC L or N 43 3 4x O6.5 6 38 405 450+20 O360 O377 O300 45 "A" 19 Connection lead p. 20 ESM_englisch_03_2009:Axial_D 09.03.2009 14:42 Seite 20 Connection leads a - Design: Cable conforms to UL standards, sealed plug 10 40 31,5 22,5 27,5 7 9,3 Jacketed cable, internal line (UL Style 2464/1061) 3 x AWG20 (approx. 0.5 mm2) Connection lines for energy-saving motors (ESM) Part no. 10637-4-1040 a 450 10640-4-1040 600 10638-4-1040 1500 10639-4-1040 2000 subject to alterations 20 Brass lead tips ESM_englisch_03_2009:Axial_D 09.03.2009 14:42 Seite 21 21 ESM_englisch_03_2009:Axial_D 09.03.2009 fan agent compact fan agent 14:42 Seite 22 ebm-papst representatives & subsidiaries motor specialist motor agent Germany ebm-papst Mulfingen GmbH & Co. KG ebm-papst St. Georgen GmbH & Co. KG ebm-papst Landshut GmbH Bachmuhle 2 D-74673 Mulfingen Phone +49 (0) 79 38 / 81-0 Fax +49 (0) 79 38 / 81-110 info1@de.ebmpapst.com Hermann-Papst-Strae 1 D-78112 St. Georgen Phone +49 (0) 77 24 / 81-0 Fax +49 (0) 77 24 / 81-13 09 info2@de.ebmpapst.com Hofmark-Aich-Strae 25 D-84030 Landshut Phone +49 (0) 8 71 / 707-0 Fax +49 (0) 8 71 / 707-465 info3@de.ebmpapst.com www.ebmpapst.com www.ebmpapst.com www.ebmpapst.com Agencies Berlin Dipl.-Ing. (TH) Jens Duchow Handelstrae 7 D-16341 Panketal Phone +49 (0) 30 / 94 41 49 62 Fax +49 (0) 30 / 94 41 49 63 Jens.Duchow@de.ebmpapst.com Bielefeld Dipl.-Ing. (FH) Wolf-Jurgen Weber Niehausweg 13 D-33739 Bielefeld Phone +49 (0) 52 06 / 9 17 32 31 Fax +49 (0) 52 06 / 9 17 32 35 Wolf-Juergen.Weber@de.ebmpapst.com Dortmund Dipl.-Ing. (FH) Hans-Joachim Pundt Auf den Steinern 3 D-59519 Mohnesee-Vollinghausen Phone +49 (0) 29 25 / 80 04 07 Fax +49 (0) 29 25 / 80 04 08 Hans-Joachim.Pundt@de.ebmpapst.com Frankfurt Dipl.-Ing. Christian Kleffmann Dr.-Hermann-Krause-Strae 23 D-63452 Hanau Phone +49 (0) 61 81 / 18 98 12 Fax +49 (0) 61 81 / 18 98 13 Christian.Kleffmann@de.ebmpapst.com Halle Dipl.-Ing. (TU) Michael Hanning Lerchenweg 4 D-06120 Lieskau Phone +49 (0) 3 45 / 5 51 24 56 Fax +49 (0) 3 45 / 5 51 24 57 Michael.Hanning@de.ebmpapst.com Hamburg Ingenieurburo Breuell GmbH Ing. Dirk Kahl Elektroingenieur Grutzmuhlenweg 40 D-22339 Hamburg Phone +49 (0) 40 / 53 80 92 55 Fax +49 (0) 40 / 53 80 92 84 Dirk.Kahl@de.ebmpapst.com 22 Kassel Dipl.-Ing. (FH) Ralph Bruck Hoherainstrae 38 D-35075 Gladenbach Phone +49 (0) 64 62 / 40 71 10 Fax +49 (0) 64 62 / 40 71 11 Ralph.Brueck@de.ebmpapst.com Koblenz Winfried Schaefer Hinter der Kirch 10 D-56767 Uersfeld Phone +49 (0) 26 57 / 16 96 Fax +49 (0) 26 57 / 16 76 Winfried.Schaefer@de.ebmpapst.com Munich Dipl.-Wirtsch.-Ing. (FH) Jens Peter Steinbergweg 6 D-82285 Hattenhofen Phone +49 (0) 81 45 / 80 92 25 Fax +49 (0) 81 45 / 80 92 26 Jens.Peter@de.ebmpapst.com Nuremberg Friedrich Klein Adlerstrae 49/1 D-73540 Heubach Phone +49 (0) 71 73 / 49 83 Fax +49 (0) 71 73 / 80 53 Friedrich.Klein@de.ebmpapst.com Offenburg Dipl.-Ing. (FH) Ralf Braun Hubeneck 21 D-77704 Oberkirch Phone +49 (0) 78 02 / 98 22 52 Fax +49 (0) 78 02 / 98 22 53 Ralf.Braun@de.ebmpapst.com Stuttgart Dipl.-Ing. (FH) Rudi Weinmann Hindenburgstrae 100/1 D-73207 Plochingen Phone +49 (0) 71 53 / 92 89 80 Fax +49 (0) 71 53 / 92 89 81 Rudi.Weinmann@de.ebmpapst.com Ulm Gunter Wilhelm Allgauer Strae 7 D-89269 Vohringen Phone +49 (0) 73 06 / 92 46 08 Fax +49 (0) 73 06 / 92 46 48 Guenter.Wilhelm@de.ebmpapst.com Distributors Frankfurt R.E.D. Handelsgesellschaft mbH Gutenbergstrae 3 D-63110 Rodgau - Jugesheim Phone +49 (0) 61 06 / 84 10 Fax +49 (0) 61 06 / 84 11 11 info@red-elektromechanik.de www.red-elektromechanik.de Hamburg Breuell + Hilgenfeldt GmbH Grutzmuhlenweg 40 D-22339 Hamburg Phone +49 (0) 40 / 53 80 92 20 Fax +49 (0) 40 / 53 80 92 84 info@breuell-hilgenfeldt.de Munich A. Schweiger GmbH Ohmstrae 1 D-82054 Sauerlach Phone +49 (0) 81 04 / 8 97 0 Fax +49 (0) 81 04 / 8 97 90 info@schweiger-gmbh.de www.schweiger-gmbh.com (1 to 5 pieces) North Breuell + Hilgenfeldt GmbH Grutzmuhlenweg 40 D-22339 Hamburg Phone +49 (0) 40 / 53 80 92 20 Fax +49 (0) 40 / 53 80 92 84 ebmpapst@breuell-hilgenfeldt.de South HDS Ventilatoren Vertriebs GmbH Glaswiesenstrae 1 D-74677 Dorzbach Phone +49 (0) 79 37 / 80 29 68 Fax +49 (0) 79 37 / 80 25 78 info@hds-gmbh.net ESM_englisch_03_2009:Axial_D 09.03.2009 Europe Austria ebm-papst Motoren & Ventilatoren GmbH Westbahnstrae 5 A-4490 St. Florian Phone +43 / 72 24 / 66 01 10 Fax +43 / 72 24 / 66 01 120 info@at.ebmpapst.com www.ebmpapst.at Belarus ebm-papst Bel AgmbH Prospekt Nesavisimosti 11/2 office 325, 512 BY-220050 Minsk Phone +375 / 17 / 209 95 61 Fax +375 / 17 / 209 95 61 info@by.ebmpapst.com www.ebmpapst.by Belgium VIBO Benelux B. V. Sales office Belgium-Luxemburg Romeinsestraat 6/0101 Research Park Haasrode B-3001 Heverlee-Leuven Phone +32 / 16 / 39 62 00 Fax +32 / 16 / 39 62 20 info@vibobenelux.com www.vibobenelux.com Bulgaria ebm-papst Romania S.R.L. Str. Tirnavei Nr. 20 RO-500327 Brasov Phone +40 / 268 / 312 805 Fax +40 / 268 / 312 805 dudasludovic@xnet.ro Croatia ebm-papst Industries Kft. Ezred u. 2. H-1044 Budapest Phone +36 / 1 / 87 22 190 Fax +36 / 1 / 87 22 194 office@hu.ebmpapst.com www.ebmpapst.hu 14:42 Seite 23 Cyprus MATERO LTD 37, St. Kyriakides Avenue P.O. Box 51744 CY-3080 Limassol Phone +357 / 25 / 87 00 30 Fax +357 / 25 / 38 13 66 matero@cytanet.com.cy www.matero.com.cy Greece Helcoma Th. Rotas & Co OE Davaki 65 GR-17672 Kallithea-Attiki Phone +30 / 210 / 951 37 05 Fax +30 / 210 / 951 34 90 contact@helcoma.gr www.helcoma.gr Czech Republic / Slovakia ebm-papst CZ s.r.o. Kratka 379 CZ-66461 Rajhradice u Brna Phone +420 / 547 / 232 617 Fax +420 / 547 / 232 622 info@ebmpapst.cz www.ebmpapst.cz Hungary ebm-papst Industries Kft. Ezred u. 2. H-1044 Budapest Phone +36 / 1 / 87 22 190 Fax +36 / 1 / 87 22 194 office@hu.ebmpapst.com www.ebmpapst.hu Denmark Jenk A/S Vallensbaekvej 21 DK-2605 Brondby Phone +45 / 43 / 63 11 11 Fax +45 / 43 / 63 05 05 jenk@jenk.dk www.jenk.dk Iceland RJ Engineers Stangarhyl 1A IS-110 Reykjavik Phone +354 / 567 80 30 Fax +354 / 567 80 15 rj@rj.is www.rj.is Estonia ebm-papst Oy Eesti Filiaal Kadaka tee 3 EST-10621 Tallinn Phone +372 / 65 56 / 978 Fax +372 / 65 56 / 979 www.ebmpapst.ee Ireland ebm-papst Limited Portlaoise Business & Technology Park Mountrath Road IRL-Portlaoise, Co. Laois Phone +353 / 57 86 / 643 43 Fax +353 / 57 86 / 643 46 sales@ie.ebmpapst.com www.ebmpapst.ie Finland ebm-papst Oy Puistotie 1 FIN-02760 Espoo Phone +358 / 9 / 88 70 22 0 Fax +358 / 9 / 88 70 22 13 mailbox@ebmpapst.fi www.ebmpapst.fi France ebm-papst SARL ZI Nord - rue A. Mohler BP 62 F-67212 Obernai-Cedex Phone +33 / 820 326 266 Fax +33 / 3 / 88 67 38 83 info@ebmpapst.fr www.ebmpapst.fr Italy ebm-papst Srl Via Cornaggia 108 I-22076 Mozzate (Co) Phone +39 / 03 31 / 83 62 01 Fax +39 / 03 31 / 82 15 10 info@it.ebmpapst.com www.ebmpapst.it Macedonia ebm-papst Industries Kft. Ezred u. 2. H-1044 Budapest Phone +36 / 1 / 87 22 190 Fax +36 / 1 / 87 22 194 office@hu.ebmpapst.com www.ebmpapst.hu 23 ESM_englisch_03_2009:Axial_D 09.03.2009 fan agent compact fan agent 14:42 Seite 24 ebm-papst representatives & subsidiaries motor specialist motor agent Netherlands VIBO Benelux B. V. Engelseweg 127 Postbus 230 NL-5705 AC Helmond Phone +31 / 4 92 / 50 29 00 Fax +31 / 4 92 / 50 29 50 verkoop@vibobenelux.com www.vibobenelux.com Norway ebm-papst AS P.B. 173 Holmlia N-1203 Oslo Phone +47 / 22 / 76 33 40 Fax +47 / 22 / 61 91 73 mailbox@ebmpapst.no www.ebmpapst.no Poland ebm-papst Polska Sp. z o.o. ul. Annopol 4A PL-03236 Warszawa Phone +48 / 22 / 675 78 19 Fax +48 / 22 / 676 95 87 office@ebmpapst.pl www.ebmpapst.pl Portugal ebm-papst (Portugal), Lda. Av. Marechal Gomes da Costa, 35 e Rua Conselheiro Emidio Navarro P-1800-255 Lisboa Phone +351 / 218 / 394 880 Fax +351 / 218 / 394 759 info@pt.ebmpapst.com www.ebmpapst.pt Romania ebm-papst Romania S.R.L. Str. Tirnavei Nr. 20 RO-500327 Brasov Phone +40 / 268 / 312 805 Fax +40 / 268 / 312 805 dudasludovic@xnet.ro 24 Russia ebm-papst Ural GmbH Posadskaja-Strasse, 23(E), 3 RU-620102 Ekaterinburg Phone +7 / 343 / 233 80 00 Fax +7 / 343 / 233 77 88 Konstantin.Molokov@ru.ebmpapst.com www.ebmpapst.ur.ru Switzerland ebm-papst AG Rutisbergstrasse 1 CH-8156 Oberhasli Phone +41 / 44 / 732 20 70 Fax +41 / 44 / 732 20 77 verkauf@ebmpapst.ch www.ebmpapst.ch ebm-papst Rus GmbH Nizhegorodskaya 32, str. 15 office 420 RU-109029 Moskau Phone +7 / 495 / 671 53 93 Fax +7 / 495 / 671 53 95 info@ebmpapst.ru www.ebmpapst.ru Turkey Akantel Elektronik San. Tic. LTD. Sti. Ataturk Organize Sanayi Bolgesi 10007 SK. No.:6 TR-35620 Cigli-Izmir Phone +90 / 232 / 328 20 90 Fax +90 / 232 / 328 02 70 akantel@akantel.com.tr www.ebmpapst.com.tr ebm-papst Rus Saint-Petersburgs Filial Zastavskaya 7 RU-196084 Sankt-Petersburg Phone +7 / 812 / 449 96 07 Fax +7 / 812 / 449 96 07 spb@ru.ebmpapst.com Serbia & Montenegro ebm-papst Industries Kft. Ezred u. 2. H-1044 Budapest Phone +36 / 1 / 87 22 190 Fax +36 / 1 / 87 22 194 office@hu.ebmpapst.com www.ebmpapst.hu Spain ebm-papst Iberica S.L. Avda. del Sistema Solar, 29 E-28830 San Fernando de Henares (Madrid) Phone +34 / 91 / 678 08 94 Fax +34 / 91 / 678 15 30 ventas@ebmpapst.es Sweden ebm-papst AB Aggelundavagen 2 S-17562 Jarfalla Phone +46 / 8 / 761 94 00 Fax +46 / 8 / 36 23 06 info@ebmpapst.se www.ebmpapst.se Ukraine ebm-papst Ukraine LLC Lepse Boulevard, 4, Building 47 UA-03067 Kiev Phone +38 / 044 / 206 30 91 Fax +38 / 044 / 206 30 91 mail@ebmpapst.ua www.ebmpapst.ua United Kingdom ebm-papst UK Ltd. Chelmsford Business Park GB-Chelmsford Essex CM2 5EZ Phone +44 / 12 45 / 46 85 55 Fax +44 / 12 45 / 46 63 36 sales@uk.ebmpapst.com www.ebmpapst.co.uk ebm-papst Automotive & Drives (UK) Ltd. The Smithy Fidlers Lane, East Ilsley GB-Berkshire RG20 7LG Phone +44 / 87 07 / 66 51 70 Fax +44 / 87 07 / 66 51 80 A&Dsales@uk.ebmpapst.com www.ebmpapst-ad.com ESM_englisch_03_2009:Axial_D 09.03.2009 America Argentina ebm-papst de Argentina S.A. Hernandarias 148 Lomas del Mirador Pcia. de Buenos Aires (1752) Phone +54 / 11 46 57 61 35 Fax +54 / 11 46 57 20 92 ventas@ar.ebmpapst.com www.ebmpapst.com.ar Brasil ebm-papst Motores Ventiladores Ltda. Av. Jose Giorgi, 301 Galpoes B6+B7 Condominio Logical Center BR-06707-100 Cotia - Sao Paulo Phone +55 /11 / 31 64 89 00 Fax +55 /11 / 47 77 14 56 vendas@br.ebmpapst.com www.ebmpapst.com.br 14:43 Seite 25 USA ebm-papst Inc. P.O. Box 4009 100 Hyde Road USA-Farmington, CT 06034 Phone +1 / 860 / 674 15 15 Fax +1 / 860 / 674 85 36 sales@us.ebmpapst.com www.ebmpapst.us ebm-papst Automotive & Drives, Inc. 3200 Greenfield, Suite 255 USA-Dearborn, MI 48120 Phone +1 / 313 / 406 80 80 Fax +1 / 313 / 406 80 81 automotive@us.ebmpapst.com www.ebmpapst-automotive.us Africa South Africa ebm-papst South Africa (Pty) Ltd. P.O. Box 3124 1119 Yacht Avenue ZA-2040 Honeydew Phone +27 / 11 / 794 34 34 Fax +27 / 11 / 794 50 20 info@za.ebmpapst.com www.ebmpapst.co.za Canada ebm-papst Canada Inc. 1800 Ironstone Manor, Unit 2 CDN-Pickering, Ontario, L1W3J9 Phone +1 / 905 / 420 / 35 33 Fax +1 / 905 / 420 / 37 72 sales@ca.ebmpapst.com www.ebmpapst.ca Mexico ebm Industrial S.de R.L. de C.V. Paseo de Tamarindos 400-A-5to Piso Col. Bosques de las Lomas MEX-Mexico 05120, D.F. Phone +52 / 55 / 33 00 51 44 Fax +52 / 55 / 33 00 52 43 sales@mx.ebmpapst.com www.ebmpapst.com.mx 25 ESM_englisch_03_2009:Axial_D 09.03.2009 fan agent compact fan agent 14:43 Seite 26 ebm-papst representatives & subsidiaries motor specialist motor agent Asia China ebm-papst Ventilator (Shanghai) Co., Ltd. No. 418, Huajing Road WaiGaoQiao Free Trade Zone No. 2001, Yang Gao (N) Road VRC-200131 Shanghai, P.R. of China Phone +86 / 21 / 50 46 01 83 Fax +86 / 21 / 50 46 11 19 sales@cn.ebmpapst.com www.ebmpapst.com.cn Hong Kong ebm-papst Ventilator (Shanghai) Co., Ltd. Hong Kong Representative Office Unit Nos. 13-15, 9/F, Technology Park 18 On Lai Street, Siu Lek Yuen, Shatin, N.T. Hong Kong P.R. of China Phone +852 / 21 45 / 86 78 Fax +852 / 21 45 / 76 78 info@hk.ebmpapst.com India ebm NADI International Pvt Ltd. 26/3, G.N.T. Road, Erukkencherry IND-Chennai-600118 Phone +91 / 44 / 25 37 25 56 Fax +91 / 44 / 25 37 11 49 ebmnadi@md2.vsnl.net.in www.ebmnadi.com Indonesia ebm-papst Indonesia Wisma Slipi, Jl. Letjend S. Parman Kav. 12 14th Floor, No. 1410 RI-11480 Jakarta Barat Phone +62 / 21 / 53 66 19 01 Fax +62 / 21 / 53 66 19 05 salesdept@id.ebmpapst.com Israel Polak Bros. Import Agencies Ltd. 9 Hamefalsim Street IL-Kiryat Arie, Petach-Tikva 49514 Phone +972 / 3 / 910 03 00 Fax +972 / 3 / 579 66 79 polak@polak.co.il www.polak.co.il 26 Japan ebm-papst Industries Japan K.K. 12 Floor, Benex S-3 Bldg. 3-20-8 Shinyokohama, Kohoku-ku J-222-0033 Yokohama Phone +81 / 45 / 470 / 57 51 Fax +81 / 45 / 470 / 57 52 info@jp.ebmpapst.com www.ebmpapst.jp Korea ebm-papst Korea Co. Ltd. 6F, Trutec Bldg. B 6-2, Digital Media City (DMC) Sangam-Dong, Mapo-Gu ROK-Seoul 121-270 Phone +82 / 2 / 36 62 / 13 24 Fax +82 / 2 / 36 62 / 13 26 info@kr.ebmpapst.com www.ebmpapst.co.kr Malaysia ebm-papst Malaysia Representative Office Block F1, 9A-4, Jln PJU 1/42 Dataran Prima MAL-47301 Petaling Jaya Phone +60 / 3 / 78 06 54 40 Fax +60 / 3 / 78 06 54 41 salesdept@my.ebmpapst.com Singapore ebm-papst SEA Pte. Ltd. No. 23 Ubi Road 4 #06-00 Olympia Industrial Building SGP-Singapore 408620 Phone +65 / 65 51 37 89 Fax +65 / 68 42 84 39 salesdept@sg.ebmpapst.com Taiwan ETECO Engineering & Trading Corp. 10F-I, No. 92, Teh-Wei Str. RC-Tsow-Inn District, Kaohsiung Phone +886 / 7 / 557 42 68 Fax +886 / 7 / 557 27 88 eteco@ms22.hinet.net Thailand ebm-papst Thailand Co., Ltd. 99/349 Na-Nakorn Bldg., 4th Floor Chaeng Wattana Road, Thungsonghong, THA-10210 Laksi, BKK Phone +66 / 2 / 5 76 15 24 Fax +66 / 2 / 5 76 15 42 salesdept@th.ebmpapst.com United Arab Emirates ebm-papst Middle East FZE PO Box 17755 Jebel Ali Free Zone / FZS1 / AP05 UAE-Dubai Phone +971 / 4 / 886 08 26 Fax +971 / 4 / 886 08 27 info@ae.ebmpapst.com www.ebmpapst.ae ESM_englisch_03_2009:Axial_D 09.03.2009 14:43 Seite 27 Australia Australia ebm-papst A&NZ Pty Ltd. 10 Oxford Road AUS-Laverton North, Victoria, 3026 Phone +61 / 3 / 83 25 64 00 Fax +61 / 3 / 83 25 64 64 sales@ebmpapst.com.au www.ebmpapst.com.au New Zealand ebm-papst A&NZ Pty Ltd. 102 Henderson Valley Road NZ-Henderson, Auckland 1230 Phone +64 / 9 / 837 18 84 Fax +64 / 9 / 837 18 99 sales@ebmpapst.com.au www.ebmpapst.com.au 27 ESM_englisch_03_2009:Axial_D 09.03.2009 14:43 Seite 28 37804-7-8811 * GK-08/08-3' Printed in Germany ebm-papst Mulfingen GmbH & Co. KG Bachmuhle 2 D-74673 Mulfingen Phone +49 (0) 79 38 / 81-0 Fax +49 (0) 79 38 / 81-110 info1@de.ebmpapst.com www.ebmpapst.com Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: ebm-papst: W1G172-EC95-01 W1G200-EC91-27 W1G200-EC87-25 W1G200-EC95-47 S1G200-CA95-02 S1G200-CA91-02 W1G230-EB97-01 W1G230-EB89-01 W1G250-BB21-01 W1G250-BB17-01 W1G300-BB23-01 W1G300-BB19-01 S1G300-CA19-02 10640-4-1040