2 A, Low VIN, Low Noise, CMOS Linear Regulator ADP1762 Data Sheet TYPICAL APPLICATION CIRCUITS Regulation to noise sensitive applications such as radio frequency (RF) transceivers, analog-to-digital converter (ADC) and digital-to-analog converter (DAC) circuits, phase-locked loops (PLLs), voltage controlled oscillators (VCOs) and clocking integrated circuits Field-programmable gate array (FPGA) and digital signal processor (DSP) supplies Medical and healthcare Industrial and instrumentation GENERAL DESCRIPTION The ADP1762 is a low noise, low dropout (LDO) linear regulator. It is designed to operate from a single input supply with an input voltage as low as 1.10 V, without the requirement of an external bias supply, to increase efficiency and provide up to 2 A of output current. The low 62 mV typical dropout voltage at a 2 A load allows the ADP1762 to operate with a small headroom while maintaining regulation and providing better efficiency. Rev. C CIN 10F PG RPULL-UP 100k VIN VOUT CSS 10nF VOUT = 1.5V COUT 10F SENSE EN PG SS ON OFF VADJ REFCAP VREG CREG 1F CREF 1F GND Figure 1. Fixed Output Operation ADP1762 VIN = 1.7V CIN 10F PG RPULL-UP 100k VIN VOUT VOUT = 1.5V COUT 10F SENSE EN PG SS CSS 10nF VADJ VREG CREG 1F ON OFF REFCAP GND CREF 1F RADJ 10k Figure 2. Adjustable Output Operation Table 1. Related Devices Device ADP1761 APPLICATIONS ADP1762 VIN = 1.7V 12922-002 2 A maximum output current Low input voltage supply range VIN = 1.10 V to 1.98 V, no external bias supply required Fixed output voltage range: VOUT_FIXED = 0.9 V to 1.5 V Adjustable output voltage range: VOUT_ADJ = 0.5 V to 1.5 V Ultralow noise: 2 V rms, 100 Hz to 100 kHz Noise spectral density 4 nV/Hz at 10 kHz 3 nV/Hz at 100 kHz Low dropout voltage: 62 mV typical at 2 A load Operating supply current: 4.5 mA typical at no load 1.5% fixed output voltage accuracy over line, load, and temperature Excellent power supply rejection ratio (PSRR) performance 62 dB typical at 10 kHz at 2 A load 46 dB typical at 100 kHz at 2 A load Excellent load/line transient response Soft start to reduce inrush current Optimized for small 10 F ceramic capacitors Current-limit and thermal overload protection Power-good indicator Precision enable 16-lead, 3 mm x 3 mm LFCSP package 12922-001 FEATURES ADP1763 ADP1740/ ADP1741 ADP1752/ ADP1753 ADP1754/ ADP1755 Input Voltage 1.10 V to 1.98 V 1.10 V to 1.98 V 1.6 V to 3.6 V 1.6 V to 3.6 V 1.6 V to 3.6 V Maximum Current 1A Fixed/ Adjustable Fixed/adjustable 3A Fixed/adjustable 2A Fixed/adjustable 0.8 A Fixed/adjustable 1.2 A Fixed/adjustable Package 16-lead LFCSP 16-lead LFCSP 16-lead LFCSP 16-lead LFCSP 16-lead LFCSP The ADP1762 is optimized for stable operation with small 10 F ceramic output capacitors. The ADP1762 delivers optimal transient performance with minimal board area. The ADP1762 is available in fixed output voltages ranging from 0.9 V to 1.5 V. The output of the adjustable output model can be set from 0.5 V to 1.5 V through an external resistor connected between VADJ and ground. The ADP1762 has an externally programmable soft start time by connecting a capacitor to the SS pin. Short-circuit and thermal overload protection circuits prevent damage in adverse conditions. The ADP1762 is available in a small 16-lead LFCSP package for the smallest footprint solution to meet a variety of applications. Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 (c)2016-2020 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com ADP1762 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Soft Start Function ..................................................................... 11 Applications ...................................................................................... 1 Adjustable Output Voltage ....................................................... 12 General Description ......................................................................... 1 Enable Feature ............................................................................ 12 Typical Application Circuits ........................................................... 1 Power-Good (PG) Feature ........................................................ 12 Revision History ............................................................................... 2 Applications Information ............................................................. 13 Specifications .................................................................................... 3 Capacitor Selection .................................................................... 13 Input and Output Capacitor: Recommended Specifications . 4 Undervoltage Lockout ............................................................... 14 Absolute Maximum Ratings ........................................................... 5 Current-Limit and Thermal Overload Protection ................ 14 Thermal Data ................................................................................ 5 Thermal Considerations ........................................................... 14 Thermal Resistance/Parameter .................................................. 5 PCB Layout Considerations ..................................................... 17 ESD Caution.................................................................................. 5 Outline Dimensions ....................................................................... 18 Pin Configuration and Function Descriptions ............................ 6 Ordering Guide .......................................................................... 18 Typical Performance Characteristics ............................................. 7 Theory of Operation ...................................................................... 11 REVISION HISTORY 3/2020--Rev. A to Rev. B Changes to Thermal Data Section, Thermal Resistance/Parameter Section, and Table 5 .................................. 5 9/2016--Rev. 0 to Rev. A Changes to Figure 23 and Figure 24 ............................................ 11 4/2016--Revision 0: Initial Version 3/2019--Rev. A to Rev. B Changes to Figure 25 ..................................................................... 11 Rev. C | Page 2 of 18 Data Sheet ADP1762 SPECIFICATIONS VIN = VOUT + 0.2 V or VIN = 1.1 V, whichever is greater, ILOAD = 10 mA, CIN = 10 F, COUT = 10 F, CREF = 1 F, CREG = 1 F, TA = 25C, Minimum and maximum limits at TJ = -40C to +125C, unless otherwise noted. Table 2. Parameter INPUT VOLTAGE SUPPLY RANGE CURRENT Operating Supply Current Shutdown Current OUTPUT NOISE1 Noise Spectral Density POWER SUPPLY REJECTION RATIO1 Symbol VIN Test Conditions/Comments TJ = -40C to +125C IGND ILOAD = 0 A ILOAD = 10 mA ILOAD = 100 mA ILOAD = 2 A EN = GND TJ = -40C to +85C, VIN = (VOUT + 0.2 V) to 1.98 V TJ = 85C to 125C, VIN = (VOUT + 0.2 V) to 1.98 V 10 Hz to 100 kHz, VIN = 1.1 V, VOUT = 0.9 V 100 Hz to 100 kHz, VIN = 1.1 V, VOUT = 0.9 V 10 Hz to 100 kHz, VIN = 1.5 V, VOUT = 1.3 V 100 Hz to 100 kHz, VIN = 1.5 V, VOUT = 1.3 V 10 Hz to 100 kHz, VIN = 1.7 V, VOUT = 1.5 V 100 Hz to 100 kHz, VIN = 1.7 V, VOUT = 1.5 V VOUT = 0.9 V to 1.5 V, ILOAD = 100 mA At 10 kHz At 100 kHz ILOAD = 2 A, modulated VIN 10 kHz, VOUT = 1.3 V, VIN = 1.6 V 100 kHz, VOUT = 1.3 V, VIN = 1.6 V 1 MHz, VOUT = 1.3 V, VIN = 1.6 V 10 kHz, VOUT = 0.9 V, VIN = 1.2 V 100 kHz, VOUT = 0.9 V, VIN = 1.2 V 1 MHz, VOUT = 0.9 V, VIN = 1.2 V IGND-SD OUTNOISE OUTNSD PSRR OUTPUT VOLTAGE Output Voltage Range Fixed Output Voltage Accuracy Min 1.10 Typ Max 1.98 Unit V 4.5 4.9 5.5 9.4 2 8 8 8.5 14 180 mA mA mA mA A A 800 A 12 2 15 2 21 2 V rms V rms V rms V rms V rms V rms 4 3 nV/Hz nV/Hz 62 46 39 63 46 34 dB dB dB dB dB dB TA = 25C VOUT_FIXED VOUT_ADJ VOUT ADJUSTABLE PIN CURRENT IADJ ADJUSTABLE OUTPUT VOLTAGE GAIN FACTOR AD REGULATION Line Regulation Load Regulation2 DROPOUT VOLTAGE3 VOUT/VIN VOUT/IOUT VDROPOUT START-UP TIME1, 4 SOFT START CURRENT tSTART-UP ISS ILOAD = 100 mA, TA = 25C 10 mA < ILOAD < 2 A, VIN = (VOUT + 0.2 V) to 1.98 V, TJ = 0C to 85C 10 mA < ILOAD < 2 A, VIN = (VOUT + 0.2 V) to 1.98 V TA = 25C VIN = (VOUT + 0.2 V) to 1.98 V TA = 25C 0.9 0.5 -0.5 -1 1.5 1.5 +0.5 +1.5 V V % % -1.5 +1.5 % 50.5 51.0 A A 49.5 48.8 VIN = (VOUT + 0.2 V) to 1.98 V 2.95 VIN = (VOUT + 0.2 V) to 1.98 V ILOAD = 10 mA to 2 A ILOAD = 100 mA, VOUT = 1.2 V ILOAD = 2 A, VOUT = 1.2 V ILOAD = 10 nF, VOUT = 1 V 1.1 V VIN 1.98 V -0.15 Rev. C | Page 3 of 18 8 50.0 50.0 3.0 3.055 0.15 12 62 0.6 10 +0.15 0.41 23 95 12 %/V %/A mV mV ms A ADP1762 Parameter CURRENT-LIMIT THRESHOLD5 THERMAL SHUTDOWN Threshold Hysteresis POWER-GOOD (PG) OUTPUT THRESHOLD Output Voltage Falling Rising PG OUTPUT Output Voltage Low Leakage Current Delay1 PRECISION EN INPUT Logic Input High Low Input Logic Hysteresis Input Leakage Current Input Delay Time UNDERVOLTAGE LOCKOUT Input Voltage Rising Falling Hysteresis Data Sheet Symbol ILIMIT Test Conditions/Comments TSSD TSSD-HYS TJ rising 150 15 C C PGFALL PGRISE 1.1 V VIN 1.98 V 1.1 V VIN 1.98 V -7.5 -5 % % PGLOW IPG-LKG PGDELAY 1.1 V VIN 1.98 V, IPG 1 mA 1.1 V VIN 1.98 V ENRISING to PGRISING 1.1 V VIN 1.98 V 0.01 0.75 ENHIGH ENLOW ENHYS IEN-LKG tIEN-DLY UVLO UVLORISE UVLOFALL UVLOHYS Min 2.2 595 550 EN = VIN or GND From EN rising from 0 V to VIN to 0.1 x VOUT TJ = -40C to +125C TJ = -40C to +125C 0.87 Typ 3 Max 4 Unit A 0.35 1 V A ms 625 580 45 0.01 100 690 630 mV mV mV A s 1.01 0.93 90 1.06 1 V V mV 1 Guaranteed by design and characterization; not production tested. Based on an endpoint calculation using 10 mA and 2 A loads. 3 Dropout voltage is defined as the input to output voltage differential when the input voltage is set to the nominal output voltage, which applies only for output voltages above 1.1 V. 4 Start-up time is defined as the time from the rising edge of EN to VOUT being at 90% of the nominal value. 5 Current-limit threshold is defined as the current at which the output voltage drops to 90% of the specified typical value. For example, the current limit for a 1.0 V output voltage is defined as the current that causes the output voltage to drop to 90% of 1.0 V, or 0.9 V. 2 INPUT AND OUTPUT CAPACITOR: RECOMMENDED SPECIFICATIONS Table 3. Parameter CAPACITANCE1 Input Output Regulator Reference CAPACITOR EQUIVALENT SERIES RESISTANCE (ESR) CIN, COUT CREG, CREF 1 Symbol CIN COUT CREG CREF RESR Test Conditions/Comments TA = -40C to +125C Min Typ 7.0 7.0 0.7 0.7 10 10 1 1 Max Unit F F F F TA = -40C to +125C 0.001 0.001 0.5 0.2 The minimum input and output capacitance must be >7.0 F over the full range of the operating conditions. Consider the full range of the operating conditions in the application during device selection to ensure that the minimum capacitance specification is met. X7R and X5R type capacitors are recommended. Y5V and Z5U capacitors are not recommended for use with any LDO. Rev. C | Page 4 of 18 Data Sheet ADP1762 ABSOLUTE MAXIMUM RATINGS Table 4. Parameter VIN to GND EN to GND VOUT to GND SENSE to GND VREG to GND REFCAP to GND VADJ to GND SS to GND PG to GND Storage Temperature Range Operating Temperature Range Operating Junction Temperature Lead Temperature (Soldering, 10 sec) Rating -0.3 V to +2.16 V -0.3 V to +3.96 V -0.3 V to VIN -0.3 V to VIN -0.3 V to VIN -0.3 V to VIN -0.3 V to VIN -0.3 V to VIN -0.3 V to +3.96 V -65C to +150C -40C to +125C 125C 300C Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. JB of the package is based on modeling and calculation using a 4-layer board. JESD51-12, Guidelines for Reporting and Using Electronic Package Thermal Information, states that thermal characterization parameters are not the same as thermal resistances. JB measures the component power flowing through multiple thermal paths rather than a single path as in thermal resistance, JB. Therefore, JB thermal paths include convection from the top of the package as well as radiation from the package, factors that make JB more useful in realworld applications. THERMAL RESISTANCE/PARAMETER Values shown in Table 5 are calculated in compliance with JEDEC standards for thermal reporting. JA is the natural convection junction to ambient thermal resistance measured in a one cubic foot sealed enclosure. JC is the junction to case thermal resistance. JB is the junction to board thermal resistance. JB is the junction to board thermal characterization parameter. JT is the junction to top thermal characterization parameter. In applications where high maximum power dissipation exists, close attention to thermal board design is required. Thermal resistance/parameter values may vary, depending on the PCB material, layout, and environmental conditions. Table 5. Thermal Resistance/Parameter THERMAL DATA Absolute maximum ratings apply individually only, not in combination. The ADP1762 can be damaged when the junction temperature limits are exceeded. The use of appropriate thermal management techniques is recommended to ensure that the maximum junction temperature does not exceed the limits shown in Table 4. Use the following equation to calculate the junction temperature (TJ) from the board temperature (TBOARD) or package top temperature (TTOP) Package Type CP-16-221 1 JA 50.95 JB 29.31 JC-T 49.53 JC-B 8.53 JB 29.31 JT 0.3 Unit C/W Thermal resistance/parameter simulated values are based on a JEDEC 2S2P thermal test board for JT, JB, JA and JB and a JEDEC 1S0P thermal test board for JC with four thermal vias. See JEDEC JESD51-12. ESD CAUTION TJ = TBOARD + (PD x JB) TJ = TTOP + (PD x JT) JB is the junction to board thermal characterization parameter and JT is the junction to top thermal characterization parameter with units of C/W. Rev. C | Page 5 of 18 ADP1762 Data Sheet 13 SENSE 14 SS 16 EN 15 PG PIN CONFIGURATION AND FUNCTION DESCRIPTIONS VIN 1 VIN 3 12 VOUT ADP1762 TOP VIEW (Not to Scale) 10 VOUT GND 7 VOUT VADJ 8 VREG 6 9 REFCAP 5 VIN 4 11 VOUT NOTES 1. THE EXPOSED PAD IS ELECTRICALLY CONNECTED TO GND. IT IS RECOMMENDED THAT THIS PAD BE CONNECTED TO A GROUND PLANE ON THE PCB. THE EXPOSED PAD IS ON THE BOTTOM OF THE PACKAGE. 12922-003 VIN 2 Figure 3. Pin Configuration Table 6. Pin Function Descriptions Pin No. 1 to 4 Mnemonic VIN 5 REFCAP 6 VREG 7 8 GND VADJ 9 to 12 VOUT 13 SENSE 14 15 SS PG 16 EN EP Description Regulator Input Supply. Bypass VIN to GND with a 10 F or greater capacitor. Note that all four VIN pins must be connected to the source supply. Reference Filter Capacitor. Connect a 1 F capacitor from the REFCAP pin to ground. Do not connect a load to ground. Regulated Input Supply to LDO Amplifier. Bypass VREG to GND with a 1 F or greater capacitor. Do not connect a load to ground. Ground. Adjustable Voltage Pin for the Adjustable Output Option. Connect a 10 k external resistor between the VADJ pin and ground to set the output voltage to 1.5 V. For the fixed output option, leave this pin floating. Regulated Output Voltage. Bypass VOUT to GND with a 10 F or greater capacitor. Note that all four VOUT pins must be connected to the load. Sense Input. The SENSE pin measures the actual output voltage at the load and feeds it to the error amplifier. Connect VSENSE as close to the load as possible to minimize the effect of IR voltage drop between VOUT and the load. Soft Start Pin. A 10 nF capacitor connected to the SS pin and ground sets the start-up time to 0.6 ms. Power-Good Output. This open-drain output requires an external pull-up resistor. If the device is in shutdown mode, current-limit mode, or thermal shutdown mode, or if VOUT falls below 90% of the nominal output voltage, the PG pin immediately transitions low. Enable Input. Drive the EN pin high to turn on the regulator. Drive the EN pin low to turn off the regulator. For automatic startup, connect the EN pin to the VIN pin. Exposed Pad. The exposed pad is electrically connected to GND. It is recommended that this pad be connected to a ground plane on the PCB. The exposed pad is on the bottom of the package. Rev. C | Page 6 of 18 Data Sheet ADP1762 TYPICAL PERFORMANCE CHARACTERISTICS VIN = 1.5 V, VOUT = 1.3 V, TA = 25C, unless otherwise noted. OUTPUT VOLTAGE (V) 1.303 14 NO LOAD ILOAD = 10mA ILOAD = 100mA ILOAD = 1A ILOAD = 2A 12 GROUND CURRENT (mA) 1.305 1.301 1.299 10 8 6 4 1.297 -25 0 25 50 75 100 125 150 JUNCTION TEMPERATURE (C) 0 -50 12922-004 1.295 -50 NO LOAD ILOAD = 100mA ILOAD = 1A -25 ILOAD = 10mA ILOAD = 500mA ILOAD = 2A 0 25 50 75 100 125 150 JUNCTION TEMPERATURE (C) 12922-007 2 Figure 7. Ground Current vs. Junction Temperature Figure 4. Output Voltage (VOUT) vs. Junction Temperature 12 1.3035 GROUND CURRENT (mA) OUTPUT VOLTAGE (V) 10 1.3030 1.3025 1.3020 8 6 4 0.1 1 10 LOAD CURRENT (A) 0 0.01 12922-005 12 = 100mA = 1A = 1.5A = 2A GROUND CURRENT (mA) 10 1.306 1.304 1.302 8 6 4 2 1.300 1.298 1.5 1.6 10 Figure 8. Ground Current vs. Load Current 1.7 1.8 1.9 INPUT VOLTAGE (V) 2.0 12922-006 OUTPUT VOLTAGE (V) 1.308 ILOAD ILOAD ILOAD ILOAD 1 LOAD CURRENT (A) Figure 5. Output Voltage (VOUT) vs. Load Current 1.310 0.1 0 1.5 NO LOAD ILOAD = 100mA ILOAD = 1A 1.6 ILOAD = 10mA ILOAD = 500mA ILOAD = 2A 1.7 1.8 1.9 INPUT VOLTAGE (V) Figure 9. Ground Current vs. Input Voltage Figure 6. Output Voltage vs. Input Voltage Rev. C | Page 7 of 18 2 12922-009 1.3015 0.01 12922-008 2 ADP1762 140 10 GROUND CURRENT (mA) 160 SHUTDOWN CURRENT (A) 12 VIN = 1.5V VIN = 1.7V VIN = 1.9V VIN = 1.6V VIN = 1.8V VIN = 1.98V 180 120 100 80 60 40 8 6 4 20 2 0 -25 0 25 50 75 100 125 150 JUNCTION TEMPERATURE (C) 0 1.1 12922-010 -20 -50 Figure 10. Shutdown Current vs. Junction Temperature at Various Input Voltages (VIN) NO LOAD ILOAD = 100mA ILOAD = 1A 1.2 ILOAD = 10mA ILOAD = 500mA ILOAD = 2A 1.3 1.4 1.5 1.6 INPUT VOLTAGE (V) 12922-012 200 Data Sheet Figure 13. Ground Current vs. Input Voltage (in Dropout), VOUT = 1.3 V 70 3A/s SLEW RATE DROPOUT VOLTAGE (mV) 60 50 2 ILOAD 40 30 1 VOUT 20 1 10 LOAD CURRENT (A) CH1 50.0mV 12922-111 0 0.1 Figure 11. Dropout Voltage vs. Load Current, VOUT = 1.3 V B W CH2 1.00A M4.00s T 18.70% A CH2 640mA 12922-114 10 Figure 14. Load Transient Response, COUT = 10 F, VIN = 1.7 V, VOUT = 1.3V 1.35 OUTPUT VOLTAGE (V) 1.30 ILOAD ILOAD ILOAD ILOAD = 100mA = 1A = 1.5A = 2A 3A/s SLEW RATE 2 ILOAD 1.25 1.20 1 VIN 1.3 1.4 INPUT VOLTAGE (V) 1.5 CH1 50.0mV CH2 1.00A M4.00s T 19.00% A CH2 640mA 12922-115 1.10 1.2 12922-112 1.15 Figure 12. Output Voltage vs. Input Voltage (in Dropout), VOUT = 1.3 V Figure 15. Load Transient Response, COUT = 47 F, VIN = 1.7 V, VOUT = 1.3 V Rev. C | Page 8 of 18 Data Sheet ADP1762 -10 VIN = 1.1V VIN = 1.2V VIN = 1.3V VIN = 1.4V VIN = 1.5V VIN = 1.6V -20 1V/s SLEW RATE -30 VIN PSRR (dB) -40 VOUT 1 2 -50 -60 -70 -80 -90 CH2 500mV M2.00s T 17.50% A CH2 1.68V -110 1 100 1k 10k 100k 1M 10M FREQUENCY (Hz) Figure 19. Power Supply Rejection Ratio (PSRR) vs. Frequency for Various VIN, VOUT = 0.9 V, Load Current = 2 A Figure 16. Line Transient Response, Load Current = 2 A, VIN = 1.5 V to 1.98 V Step, VOUT = 1.3 V -10 16 VOUT = 1.3V (10Hz TO 100kHz) VIN = 1.5V VIN = 1.6V VIN = 1.7V VIN = 1.8V VIN = 1.9V VIN = 1.98V -20 14 -30 12 -40 10 PSRR (dB) NOISE (V rms) 10 12922-019 CH1 5.00mV 12922-116 -100 8 6 -50 -60 -70 -80 4 -90 VOUT = 1.3V (100Hz TO 100kHz) 1 10 LOAD CURRENT (A) -110 1 100 1k 10k 100k 1M 10M FREQUENCY (Hz) Figure 20. Power Supply Rejection Ratio (PSRR) vs. Frequency for Various VIN, VOUT = 1.3 V, Load Current = 2 A Figure 17. Noise vs. Load Current for Various Output Voltages -10 10k VIN = 1.7V VIN = 1.8V VIN = 1.9V VIN = 1.98V -20 -30 1k -40 PSRR (dB) 100 10 -50 -60 -70 -80 -90 1 100 -100 1k FREQUENCY (Hz) 10k 100k Figure 18. Noise Spectral Density vs. Frequency for Various Output Voltages, ILOAD = 100 mA Rev. C | Page 9 of 18 -110 1 10 100 1k 10k 100k 1M 10M FREQUENCY (Hz) Figure 21. Power Supply Rejection Ratio (PSRR) vs. Frequency for Various VIN, VOUT = 1.5 V, Load Current = 2 A 12922-021 0.1 10 VOUT = 0.9V VOUT = 1.3V VOUT = 1.5V 12922-015 NOISE SPECTRAL DENSITY (nV/Hz) 10 12922-020 0 0.1 -100 12922-013 2 ADP1762 -10 Data Sheet ILOAD = 200mA ILOAD = 500mA ILOAD = 1A ILOAD = 2A -20 -30 PSRR (dB) -40 -50 -60 -70 -80 -90 -110 1 10 100 1k 10k 100k 1M 10M FREQUENCY (Hz) 12922-022 -100 Figure 22. Power Supply Rejection Ratio (PSRR) vs. Frequency for Various Loads, VOUT = 1.3 V, VIN = 1.6 V Rev. C | Page 10 of 18 Data Sheet ADP1762 THEORY OF OPERATION The ADP1762 is an LDO, low noise linear regulator that uses an advanced proprietary architecture to achieve high efficiency regulation. It also provides high PSRR and excellent line and load transient response using a small 10 F ceramic output capacitor. The device operates from a 1.10 V to 1.98 V input rail to provide up to 2 A of output current. Supply current in shutdown mode is 2 A. ADP1762 VIN EN SHORT-CIRCUIT, THERMAL PROTECTION For applications that require a controlled startup, the ADP1762 provides a programmable soft start function. The programmable soft start is useful for reducing inrush current upon startup and for providing voltage sequencing. To implement soft start, connect a small ceramic capacitor from SS to ground. At startup, a 10 A current source charges this capacitor. The voltage at SS limits the ADP1762 start-up output voltage, providing a smooth ramp-up to the nominal output voltage. To calculate the startup time for the fixed output and adjustable output, use the following equations: SS BLOCK tSTART-UP_FIXED = tDELAY + VREF x (CSS/ISS) SS REFCAP Figure 23. Functional Block Diagram, Fixed Output ADP1762 tSTART-UP_ADJ = tDELAY + VADJ x (CSS/ISS) (2) where: tDELAY is a fixed delay of 100 s. VREF is a 0.5 V internal reference for the fixed output model option. CSS is the soft start capacitance from SS to GND. ISS is the current sourced from SS (10 A). VADJ is the voltage at the VADJ pin equal to RADJ x IADJ. 1.7 INTERNAL BIAS SUPPLY SHORT-CIRCUIT, THERMAL PROTECTION 1.5 SENSE 1.3 IADJ 1.1 VOUT, EN (V) EN VADJ (1) VOUT VIN VREG SOFT START FUNCTION PG REFERENCE, BIAS GND SENSE 12922-023 VREG VOUT INTERNAL BIAS SUPPLY The ADP1762 uses the EN pin to enable and disable the VOUT pin under normal operating conditions. When EN is high, VOUT turns on. When EN is low, VOUT turns off. For automatic startup, tie EN to VIN. 3x 0.9 0.7 0.5 PG 0.3 -0.1 -0.2 SS REFCAP 0.8 1.3 1.8 TIME (ms) Figure 25. Fixed VOUT Ramp-Up with External Soft Start Capacitor (VOUT, EN) vs. Time 2.0 Figure 24. Functional Block Diagram, Adjustable Output 1.5 VOUT, EN (V) Internally, the ADP1762 consists of a reference, an error amplifier, and a pass device. The output current is delivered via the pass device, which is controlled by the error amplifier, forming a negative feedback system that ideally drives the feedback voltage to equal the reference voltage. If the feedback voltage is lower than the reference voltage, the negative feedback drives more current, increasing the output voltage. If the feedback voltage is higher than the reference voltage, the negative feedback drives less current, decreasing the output voltage. 0.3 The ADP1762 is available in output voltages ranging from 0.9 V to 1.5 V for a fixed output. Contact a local Analog Devices, Inc., sales representative for other fixed voltage options. The adjustable output option can be set from 0.5 V to 1.5 V. Rev. C | Page 11 of 18 1.0 0.5 EN VOUT = 0.5V; CSS VOUT = 0.5V; CSS VOUT = 1.5V; CSS VOUT = 1.5V; CSS 0 -0.5 -0.2 0.3 0.8 1.3 = 10nF = 22nF = 10nF = 22nF 1.8 TIME (ms) Figure 26. Adjustable VOUT Ramp-Up with External Soft Start Capacitor (VOUT, EN) vs. Time 12922-226 SS BLOCK 12919-024 GND 12922-025 EN CSS = 0nF CSS = 10nF CSS = 22nF 0.1 ADP1762 Data Sheet ADJUSTABLE OUTPUT VOLTAGE POWER-GOOD (PG) FEATURE The output voltage of the ADP1762 can be set over a 0.5 V to 1.5 V range. Connect a resistor (RADJ) from the VADJ pin to ground to set the output voltage. To calculate the output voltage, use the following equation: The ADP1762 provides a power-good pin (PG) to indicate the status of the output. This open-drain output requires an external pull-up resistor that can be connected to VIN or VOUT. If the device is in shutdown mode, current-limit mode, or thermal shutdown, or if it falls below 90% of the nominal output voltage, PG immediately transitions low. During soft start, the rising threshold of the power-good signal is 95% of the nominal output voltage. VOUT = AD x (RADJ x IADJ) (3) where: AD is the gain factor with a typical value of 3.0 between the VADJ pin and VOUT pin. IADJ is the 50.0 A constant current out of the VADJ pin. ENABLE FEATURE The ADP1762 uses the EN pin to enable and disable the VOUT pins under normal operating conditions. As shown in Figure 27, when a rising voltage on EN crosses the active threshold, VOUT turns on. When a falling voltage on EN crosses the inactive threshold, VOUT turns off. EN The open-drain output is held low when the ADP1762 has a sufficient input voltage to turn on the internal PG transistor. An optional soft start delay can be detected. The PG transistor is terminated via a pull-up resistor to VOUT or VIN. Power-good accuracy is 92.5% of the nominal regulator output voltage when this voltage is rising, with a 95% trip point when this voltage is falling. Regulator input voltage brownouts or glitches trigger a power no good if VOUT falls below 92.5%. A normal power-down triggers a power good when VOUT is at 95%. VOUT VIN 1 VOUT 2 CH1 200mV B W CH2 200mV B W M4.0ms A CH1 T 8.26ms 768mV 12922-026 1 PG 4 As shown in Figure 28, the EN pin has hysteresis built in. This hysteresis prevents on/off oscillations that can occur due to noise on the EN pin as it passes through the threshold points. CH1 1.00V CH2 1.00V CH4 1.00V M100s A CH4 T 228.0000s 420mV 12922-027 Figure 27. Typical EN Pin Operation Figure 29. Typical PG Behavior vs. VOUT, VIN Rising (VOUT = 1.3 V) 1.4 1.3 VIN 1.2 1.0 1 0.9 VOUT 0.8 0.7 0.6 2 PG 0.5 0.4 0.3 0.1 0 0.55 0.56 0.57 0.58 0.59 0.60 0.61 0.62 0.63 0.64 0.65 EN VOLTAGE (V) Figure 28. Output Voltage vs. Typical EN Pin Voltage, VOUT = 1.3 V Rev. C | Page 12 of 18 CH1 1.00V CH2 1.00V CH4 1.00V M200s A CH1 T 0.000000s 3.00V 12922-128 4 0.2 12922-127 OUTPUT VOLTAGE (V) 1.1 Figure 30. Typical PG Behavior vs. VOUT, VIN Falling (VOUT = 1.3 V) Data Sheet ADP1762 APPLICATIONS INFORMATION CAPACITOR SELECTION Input and Output Capacitor Properties Output Capacitor Use any good quality ceramic capacitors with the ADP1762, as long as they meet the minimum capacitance and maximum ESR requirements. Ceramic capacitors are manufactured with a variety of dielectrics, each with different behavior over temperature and applied voltage. Capacitors must have a dielectric adequate to ensure the minimum capacitance over the necessary temperature range and dc bias conditions. X5R or X7R dielectrics with a voltage rating of 6.3 V or 10 V are recommended. Y5V and Z5U dielectrics are not recommended, due to poor temperature and dc bias characteristics. The ADP1762 is designed for operation with small, spacesaving ceramic capacitors, but it can function with most commonly used capacitors as long as care is taken with the effective series resistance (ESR) value. The ESR of the output capacitor affects the stability of the LDO control loop. A minimum of 10 F capacitance with an ESR of 500 m or less is recommended to ensure the stability of the ADP1762. Transient response to changes in load current is also affected by output capacitance. Using a larger value of output capacitance improves the transient response of the ADP1762 to large changes in load current. Figure 31 and Figure 32 show the transient responses for output capacitance values of 10 F and 47 F, respectively. 2 ILOAD Figure 33 shows the capacitance vs. bias voltage characteristics of an 0805 case, 10 F, 10 V, X5R capacitor. The voltage stability of a capacitor is strongly influenced by the capacitor size and voltage rating. In general, a capacitor in a larger package or with a higher voltage rating exhibits better stability. The temperature variation of the X5R dielectric is about 15% over the -40C to +85C temperature range and is not a function of package size or voltage rating. 12 10 W CH2 1.00A M1.00s T 18.70% A CH2 640mA 8 6 4 2 Figure 31. Output Transient Response, COUT = 10 F 0 0 1 2 3 4 5 DC BIAS VOLTAGE (V) 1 Figure 33. Capacitance vs. DC Bias Voltage ILOAD Use Equation 4 to determine the worst case capacitance, accounting for capacitor variation over temperature, component tolerance, and voltage. VIN CEFF = COUT x (1 - tempco) x (1 - TOL) CH1 50.0mV CH2 1.00A M1.00s T 19.00% A CH2 640mA (4) where: CEFF is the effective capacitance at the operating voltage. COUT is the output capacitor. Tempco is the worst case capacitor temperature coefficient. TOL is the worst case component tolerance. 12922-131 2 6 12922-032 B CAPACITANCE (F) CH1 50.0mV 12922-130 1 VOUT Figure 32. Output Transient Response, COUT = 47 F Input Bypass Capacitor Connecting a 10 F capacitor from the VIN pin to the GND pin to ground reduces the circuit sensitivity to the PCB layout, especially when long input traces or high source impedance are encountered. If output capacitance greater than 10 F is required, it is recommended that the input capacitor be increased to match it. In this example, the worst case temperature coefficient (tempco) over -40C to +85C is assumed to be 15% for an X5R dielectric. The tolerance of the capacitor (TOL) is assumed to be 10%, and COUT = 10 F at 1.0 V, as shown in Figure 33. Substituting these values in Equation 4 yields Rev. C | Page 13 of 18 CEFF = 10 F x (1 - 0.15) x (1 - 0.1) = 7.65 F ADP1762 Data Sheet Therefore, the capacitor chosen in this example meets the minimum capacitance requirement of the LDO over temperature and tolerance at the chosen output voltage. To guarantee the performance of the ADP1762, it is imperative that the effects of dc bias, temperature, and tolerances on the behavior of the capacitors be evaluated for each application. UNDERVOLTAGE LOCKOUT The ADP1762 has an internal undervoltage lockout circuit that disables all inputs and the output when the input voltage is less than approximately 1.06 V. The UVLO ensures that the ADP1762 inputs and the output behave in a predictable manner during power-up. CURRENT-LIMIT AND THERMAL OVERLOAD PROTECTION The ADP1762 is protected against damage due to excessive power dissipation by current-limit and thermal overload protection circuits. The ADP1762 is designed to reach the current limit when the output load reaches 3 A (typical). When the output load exceeds 3 A, the output voltage is reduced to maintain a constant current limit. Thermal overload protection is included, which limits the junction temperature to a maximum of 150C (typical). Under extreme conditions (that is, high ambient temperature and power dissipation) when the junction temperature begins to rise above 150C, the output is turned off, reducing the output current to zero. When the junction temperature drops below 135C (typical), the output is turned on again, and the output current is restored to the nominal value. Consider the case where a hard short from VOUT to ground occurs. At first, the ADP1762 reaches the current limit so that only 3 A is conducted into the short circuit. If self heating of the junction becomes great enough to cause the temperature to rise above 150C, thermal shutdown activates, turning off the output and reducing the output current to zero. As the junction temperature cools and drops below 135C, the output turns on and conducts 3 A into the short circuit, again causing the junction temperature to rise above 150C. This thermal oscillation between 135C and 150C causes a current oscillation between 3 A and 0 A that continues as long as the short circuit remains at the output. Current-limit and thermal overload protections are intended to protect the device against accidental overload conditions. For reliable operation, limit the device power externally so that junction temperatures do not exceed 125C. THERMAL CONSIDERATIONS To guarantee reliable operation, the junction temperature of the ADP1762 must not exceed 125C. To ensure that the junction temperature stays below this maximum value, the user needs to be aware of the parameters that contribute to junction temperature changes. These parameters include ambient temperature, power dissipation in the power device, and thermal resistance between the junction and ambient air (JA). The JA value is dependent on the package assembly compounds used and the amount of copper to which the GND pin and the exposed pad (EPAD) of the package are soldered on the PCB. Table 7 shows typical JA values for the 16-lead LFCSP for various PCB copper sizes. Table 8 shows typical JB values for the 16-lead LFCSP. Table 7. Typical JA Values Copper Size (mm2) 25 100 500 1000 6400 JA (C/W), LFCSP 138.1 102.9 76.9 67.3 56 Table 8. Typical JB Values Copper Size (mm2) 100 500 1000 JB (C/W) at 1 W 33.3 28.9 28.5 To calculate the junction temperature of the ADP1762, use the following equation: TJ = TA + (PD x JA) (5) where: TA is the ambient temperature. PD is the power dissipation in the die, given by PD = ((VIN - VOUT) x ILOAD) + (VIN x IGND) where: VIN and VOUT are the input and output voltages, respectively. ILOAD is the load current. IGND is the ground current. As shown in Equation 6, for a given ambient temperature and computed power dissipation, a minimum copper size requirement exists for the PCB to ensure that the junction temperature does not rise above 125C. Rev. C | Page 14 of 18 (6) Data Sheet ADP1762 140 Figure 34 through Figure 39 show the junction temperature calculations for the different ambient temperatures, load currents, VIN to VOUT differentials, and areas of PCB copper. TJ MAX JUNCTION TEMPERATURE (C) 120 140 TJ MAX 2A 100 1A 80 500mA 60 40 100mA 20 10mA 100 500mA 80 100mA 60 10mA 40 20 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 VIN - VOUT (V) 12922-037 JUNCTION TEMPERATURE (C) 120 1A 2A Figure 37. 6400 mm2 of PCB Copper, TA = 50C 0.4 0.6 0.8 1.0 1.2 1.4 1.6 VIN - VOUT (V) 140 TJ MAX 100 500mA 80 60 2A 1A 500mA 100 80 100mA 60 10mA 40 20 40 100mA 20 10mA 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 VIN - VOUT (V) 12922-038 JUNCTION TEMPERATURE (C) 1A 2A TJ MAX 120 JUNCTION TEMPERATURE (C) Figure 34. 6400 mm2 of PCB Copper, TA = 25C 120 140 12922-034 0 0.2 Figure 38. 500 mm2 of PCB Copper, TA = 50C 0.4 0.6 0.8 1.0 1.2 1.4 1.6 VIN - VOUT (V) 140 TJ MAX 500mA 100 80 60 2A 1A 500mA 100 80 100mA 60 10mA 40 20 40 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 VIN - VOUT (V) 10mA 20 Figure 39. 25 mm2 of PCB Copper, TA = 50C 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 VIN - VOUT (V) 1.6 Figure 36. 25 mm2 of PCB Copper, TA = 25C Rev. C | Page 15 of 18 1.6 12922-039 100mA 12922-036 JUNCTION TEMPERATURE (C) 1A 2A TJ MAX 120 JUNCTION TEMPERATURE (C) Figure 35. 500 mm2 of PCB Copper, TA = 25C 120 140 12922-035 0 0.2 ADP1762 Data Sheet Figure 40 through Figure 43 show the junction temperature calculations for the different board temperatures, load currents, VIN to VOUT differentials, and areas of PCB copper. 140 80 1A 60 500mA 40 0 0.2 100mA 10mA 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.6 VIN - VOUT (V) 2A Figure 42. 1000 mm2 of PCB Copper, TB = 25C 80 140 1A 60 40 100mA 10mA 20 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 VIN - VOUT (V) Figure 40. 500 mm2 of PCB Copper, TB = 25C JUNCTION TEMPERATURE (C) 120 500mA 12922-040 JUNCTION TEMPERATURE (C) 120 100 2A 20 TJ MAX 140 120 100 1A 80 500mA 60 100mA 10mA 40 0 0.2 2A 0.4 0.6 0.8 1.0 1.2 1.4 VIN - VOUT (V) 100 1A 80 Figure 43. 1000 mm2 of PCB Copper, TB = 50C 500mA 60 100mA 10mA 40 0.4 0.6 0.8 1.0 1.2 1.4 VIN - VOUT (V) 1.6 12922-041 20 0 0.2 2A 20 TJ MAX JUNCTION TEMPERATURE (C) 100 12922-042 (7) TJ MAX 120 12922-043 TJ = TB + (PD x JB) 140 JUNCTION TEMPERATURE (C) In cases where the board temperature is known, the thermal characterization parameter (JB) can be used to estimate the junction temperature rise. The maximum junction temperature (TJ) is calculated from the board temperature (TB) and power dissipation (PD) using the following formula: Figure 41. 500 mm2 of PCB Copper, TB = 50C Rev. C | Page 16 of 18 Data Sheet ADP1762 PCB LAYOUT CONSIDERATIONS Heat dissipation from the package can be improved by increasing the amount of copper attached to the pins of the ADP1762. However, as shown in Table 8, a point of diminishing returns is eventually reached, beyond which an increase in the copper size does not yield significant heat dissipation benefits. Place the input capacitor as close as possible to the VIN and GND pins. Place the output capacitor as close as possible to the VOUT and GND pins. Place the soft start capacitor (CSS) as close as possible to the SS pin. Place the reference capacitor (CREF) and regulator capacitor (CREG) as close as possible to the REFCAP pin and the VREG pin, respectively. Connect the load as close as possible to the VOUT and SENSE pins. 12922-045 Use the following recommendations when designing PCBs: Figure 45. Typical Board Layout, Top Side 12922-046 Use of 0603 or 0805 size capacitors and resistors achieves the smallest possible footprint solution on boards where area is limited. 12922-044 Figure 46. Typical Board Layout, Bottom Side Figure 44. Evaluation Board Rev. C | Page 17 of 18 ADP1762 Data Sheet OUTLINE DIMENSIONS PIN 1 INDICATOR AREA DETAIL A (JEDEC 95) 0.30 0.23 0.18 0.50 BSC 13 16 12 1 1.75 1.60 SQ 1.45 EXPOSED PAD 9 0.50 0.40 0.30 TOP VIEW 0.80 0.75 0.70 SIDE VIEW PKG-005138 4 8 0.05 MAX 0.02 NOM COPLANARITY 0.08 0.20 REF SEATING PLANE P IN 1 IN D I C ATO R AR E A OP T IO N S (SEE DETAIL A) 5 BOTTOM VIEW 0.20 MIN FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. COMPLIANT TO JEDEC STANDARDS MO-220-WEED-6 08-24-2018-E 3.10 3.00 SQ 2.90 Figure 47. 16-Lead Lead Frame Chip Scale Package [LFCSP] 3 mm x 3 mm Body and 0.75 mm Package Height (CP-16-22) Dimensions shown in millimeters ORDERING GUIDE Model1 ADP1762ACPZ-R7 ADP1762ACPZ-0.9-R7 ADP1762ACPZ0.95-R7 ADP1762ACPZ-1.0-R7 ADP1762ACPZ-1.1-R7 ADP1762ACPZ-1.2-R7 ADP1762ACPZ1.25-R7 ADP1762ACPZ-1.3-R7 ADP1762ACPZ-1.5-R7 ADP1762-1.3-EVALZ ADP1762-ADJ-EVALZ 1 2 Temperature Range -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C Output Voltage (V)2 Adjustable 0.9 0.95 1.0 1.1 1.2 1.25 1.3 1.5 1.3 1.1 Package Description 16-Lead Lead Frame Chip Scale Package [LFCSP] 16-Lead Lead Frame Chip Scale Package [LFCSP] 16-Lead Lead Frame Chip Scale Package [LFCSP] 16-Lead Lead Frame Chip Scale Package [LFCSP] 16-Lead Lead Frame Chip Scale Package [LFCSP] 16-Lead Lead Frame Chip Scale Package [LFCSP] 16-Lead Lead Frame Chip Scale Package [LFCSP] 16-Lead Lead Frame Chip Scale Package [LFCSP] 16-Lead Lead Frame Chip Scale Package [LFCSP] Evaluation Board Evaluation Board Package Option CP-16-22 CP-16-22 CP-16-22 CP-16-22 CP-16-22 CP-16-22 CP-16-22 CP-16-22 CP-16-22 Branding LRS LRT LUP LRU LRV LRW LRZ LRX LRY Z = RoHS Compliant Part. For additional options, contact a local Analog Devices sales or distribution representative. Additional voltage output options available include the following: 0.5 V, 0.55 V, 0.6 V, 0.65 V, 0.7 V, 0.75 V, 0.8 V, 0.85 V, 1.05 V, 1.15 V, 1.35 V, 1.4 V, or 1.45 V. (c)2016-2020 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D12922-3/20(C) Rev. C | Page 18 of 18