CAT5111 100tap Digital Potentiometer (POT) with Buffered Wiper Description The CAT5111 is a single digital POT designed as an electronic replacement for mechanical potentiometers. Ideal for automated adjustments on high volume production lines, they are also well suited for applications where equipment requiring periodic adjustment is either difficult to access or located in a hazardous or remote environment. The CAT5111 contains a 100-tap series resistor array connected between two terminals RH and RL. An up/down counter and decoder that are controlled by three input pins, determines which tap is connected to the wiper, RWB. The CAT5111 wiper is buffered by an op amp that operates rail to rail. The wiper setting, stored in non-volatile memory, is not lost when the device is powered down and is automatically recalled when power is returned. The wiper can be adjusted to test new system values without effecting the stored setting. Wiper-control of the CAT5111 is accomplished with three input control pins, CS, U/D, and INC. The INC input increments the wiper in the direction which is determined by the logic state of the U/D input. The CS input is used to select the device and also store the wiper position prior to power down. The digital POT can be used as a buffered voltage divider. For applications where the potentiometer is used as a 2-terminal variable resistor, please refer to the CAT5113. The buffered wiper of the CAT5111 is not compatible with that application. Features 100-position Linear Taper Potentiometer Non-volatile EEPROM Wiper Storage; Buffered Wiper Low Power CMOS Technology Single Supply Operation: 2.5 V - 6.0 V Increment Up/Down Serial Interface Resistance Values: 10 kW, 50 kW and 100 kW Available in PDIP, SOIC, TSSOP and MSOP Packages These Devices are Pb-Free, Halogen Free/BFR Free and are RoHS Compliant Applications Automated Product Calibration Remote Control Adjustments Offset, Gain and Zero Control Tamper-proof Calibrations Contrast, Brightness and Volume Controls Motor Controls and Feedback Systems Programmable Analog Functions Semiconductor Components Industries, LLC, 2013 June, 2013 - Rev. 20 http://onsemi.com SOIC-8 V SUFFIX CASE 751BD MSOP-8 Z SUFFIX CASE 846AD PDIP-8 L SUFFIX CASE 646AA TSSOP-8 Y SUFFIX CASE 948AL PIN CONFIGURATIONS INC U/D RH GND 1 VCC CS RL RWB PDIP (L), SOIC (V), MSOP (Z) CS VCC INC U/D 1 RL RWB GND RH TSSOP (Y) (Top Views) PIN FUNCTION Pin Name Function INC Increment Control U/D Up/Down Control RH Potentiometer High Terminal GND Ground RWB Buffered Wiper Terminal RL Potentiometer Low Terminal CS Chip Select VCC Supply Voltage ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 9 of this data sheet. 1 Publication Order Number: CAT5111/D CAT5111 DEVICE MARKING INFORMATION PDIP SOIC RL4A CAT5111VT YMXXXX RL4A CAT5111LT YMXXXX MSOP TSSOP AARL YMP A1RL 4YMXXX R = Resistance: AARL = CAT5111ZI-10-T3 AAPT = CAT5111ZI-50-T3 2 = 10 kW AAPX = CAT5111ZI-00-T3 4 = 50 kW Y = Production Year (Last Digit) 5 = 100 kW M = Production Month (1-9, A, B, C) L = Assembly Location P = Product Revision 4 = Lead Finish - NiPdAu A = Product Revision (Fixed as "A") CAT5111L = Device Code (PDIP) CAT5111V = Device Code (SOIC) T = Temperature Range (Industrial) Y = Production Year (Last Digit) M = Production Month (1-9, A, B, C) XXXX = Last Four Digits of Assembly Lot Number A1 = Device Code R = Resistance: 2 = 10 kW 4 = 50 kW 5 = 100 kW L = Assembly Location 4 = Lead Finish - NiPdAu Y = Production Year (Last Digit) M = Production Month (1-9, A, B, C) XXX = Last Three Digits of XXX = Assembly Lot Number RH VCC RH U/D INC Control and Memory CS + - + RWB - Power On Recall RWB RL GND RL Figure 1. Functional Diagram Figure 2. Electronic Potentiometer Implementation http://onsemi.com 2 CAT5111 Pin Description INC: Increment Control Input The INC input (on the falling edge) moves the wiper in the up or down direction determined by the condition of the U/D input. U/D: Up/Down Control Input The U/D input controls the direction of the wiper movement. When in a high state and CS is low, any high-to-low transition on INC will cause the wiper to move one increment toward the RH terminal. When in a low state and CS is low, any high-to-low transition on INC will cause the wiper to move one increment towards the RL terminal. RH: High End Potentiometer Terminal RH is the high end terminal of the potentiometer. It is not required that this terminal be connected to a potential greater than the RL terminal. Voltage applied to the RH terminal cannot exceed the supply voltage, VCC or go below ground, GND. RWB: Wiper Potentiometer Terminal (Buffered) RWB is the buffered wiper terminal of the potentiometer. Its position on the resistor array is controlled by the control inputs, INC, U/D and CS. RL: Low End Potentiometer Terminal RL is the low end terminal of the potentiometer. It is not required that this terminal be connected to a potential less than the RH terminal. Voltage applied to the RL terminal cannot exceed the supply voltage, VCC or go below ground, GND. RL and RH are electrically interchangeable. CS: Chip Select The chip select input is used to activate the control input of the CAT5111 and is active low. When in a high state, activity on the INC and U/D inputs will not affect or change the position of the wiper. Device Operation The CAT5111 operates like a digitally controlled potentiometer with RH and RL equivalent to the high and low terminals and RWB equivalent to the mechanical potentiometer's wiper. There are 100 available tap positions including the resistor end points, RH and RL. There are 99 resistor elements connected in series between the RH and RL terminals. The wiper terminal is connected to one of the 100 taps and controlled by three inputs, INC, U/D and CS. These inputs control a seven-bit up/down counter whose output is decoded to select the wiper position. The selected wiper position can be stored in nonvolatile memory using the INC and CS inputs. With CS set LOW the CAT5111 is selected and will respond to the U/D and INC inputs. HIGH to LOW transitions on INC will increment or decrement the wiper (depending on the state of the U/D input and seven-bit counter). The wiper, when at either fixed terminal, acts like its mechanical equivalent and does not move beyond the last position. The value of the counter is stored in nonvolatile memory whenever CS transitions HIGH while the INC input is also HIGH. When the CAT5111 is powered-down, the last stored wiper counter position is maintained in the nonvolatile memory. When power is restored, the contents of the memory are recalled and the counter is set to the value stored. With INC set low, the CAT5111 may be de-selected and powered down without storing the current wiper position in nonvolatile memory. This allows the system to always power up to a preset value stored in nonvolatile memory. http://onsemi.com 3 CAT5111 Table 1. OPERATION MODES INC CS U/D Operation High to Low Low High Wiper toward RH High to Low Low Low Wiper toward RL High Low to High X Store Wiper Position Low Low to High X No Store, Return to Standby X High X Standby RH CH RWI RWB CW CL RL Figure 3. Potentiometer Equivalent Circuit Table 2. ABSOLUTE MAXIMUM RATINGS Parameters Ratings Supply Voltage VCC to GND -0.5 to +7 Inputs CS to GND -0.5 to VCC +0.5 Units V V INC to GND -0.5 to VCC +0.5 V U/D to GND -0.5 to VCC +0.5 V RH to GND -0.5 to VCC +0.5 V RL to GND -0.5 to VCC +0.5 V RWB to GND -0.5 to VCC +0.5 V Operating Ambient Temperature Commercial (`C' or Blank suffix) C 0 to 70 Industrial (`I' suffix) -40 to +85 C Junction Temperature +150 C Storage Temperature -65 to 150 C +300 C Lead Soldering (10 s max) Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. Table 3. RELIABILITY CHARACTERISTICS Symbol Parameter VZAP (Note 1) ESD Susceptibility MIL-STD-883, Test Method 3015 2000 V Latch-Up JEDEC Standard 17 100 mA Data Retention MIL-STD-883, Test Method 1008 100 Years Endurance MIL-STD-883, Test Method 1003 1,000,000 Stores ILTH (Notes 1, 2) TDR NEND Test Method Min Typ 1. This parameter is tested initially and after a design or process change that affects the parameter. 2. Latch-up protection is provided for stresses up to 100 mA on address and data pins from -1 V to VCC + 1 V http://onsemi.com 4 Max Units CAT5111 Table 4. DC ELECTRICAL CHARACTERISTICS (VCC = +2.5 V to +6 V unless otherwise specified) Min Typ Max Units 2.5 - 6 V VCC = 6 V, f = 1 MHz, IW = 0 - - 200 mA VCC = 6 V, f = 250 kHz, IW = 0 - - 100 mA Programming, VCC = 6 V - - 1000 mA VCC = 3 V - - 500 mA Supply Current (Standby) CS = VCC - 0.3 V U/D, INC = VCC - 0.3 V or GND - 75 150 mA IIH Input Leakage Current VIN = VCC - - 10 mA IIL Input Leakage Current VIN = 0 V - - -10 mA VIH1 TTL High Level Input Voltage 4.5 V VCC 5.5 V 2 - VCC V VIL1 TTL Low Level Input Voltage 0 - 0.8 V VIH2 CMOS High Level Input Voltage VCC x 0.7 - VCC + 0.3 V VIL2 CMOS Low Level Input Voltage -0.3 - VCC x 0.2 V Symbol Parameter Conditions POWER SUPPLY VCC Operating Voltage Range ICC1 Supply Current (Increment) ICC2 Supply Current (Write) ISB1 (Note 4) LOGIC INPUTS 2.5 V VCC 6 V POTENTIOMETER CHARACTERISTICS RPOT Potentiometer Resistance -10 Device 10 -50 Device 50 -00 Device 100 Pot. Resistance Tolerance 20 % VRH Voltage on RH pin 0 VCC V VRL Voltage on RL pin 0 VCC V Resolution 1 % INL Integral Linearity Error IW 2 mA 0.5 1 LSB DNL Differential Linearity Error IW 2 mA 0.25 0.5 LSB ROUT Buffer Output Resistance 0.05 VCC VWB 0.95 VCC, VCC = 5 V 1 W IOUT Buffer Output Current 0.05 VCC VWB 0.95 VCC, VCC = 5 V 3 mA TCRPOT TC of Pot Resistance TCRATIO Ratiometric TC CRH/CRL/CRW 3. 4. 5. 6. kW 300 ppm/C 20 Potentiometer Capacitances 8/8/25 fc Frequency Response Passive Attenuator, 10 kW VWB(SWING) Output Voltage Range IOUT 100 mA, VCC = 5 V This parameter is tested initially and after a design or process change that affects the parameter. Latch-up protection is provided for stresses up to 100 mA on address and data pins from -1 V to VCC + 1 V IW = source or sink These parameters are periodically sampled and are not 100% tested. http://onsemi.com 5 pF 1.7 0.01 VCC ppm/C MHz 0.99 VCC CAT5111 Table 5. AC TEST CONDITIONS VCC Range 2.5 V VCC 6 V Input Pulse Levels 0.2 VCC to 0.7 VCC Input Rise and Fall Times 10 ns Input Reference Levels 0.5 VCC Table 6. AC OPERATING CHARACTERISTICS (VCC = +2.5 V to +6.0 V, VH = VCC, VL = 0 V, unless otherwise specified) Parameter Symbol Min Typ (Note 7) Max Units 100 - - ns tCI CS to INC Setup tDI U/D to INC Setup 50 - - ns tID U/D to INC Hold 100 - - ns tIL INC LOW Period 250 - - ns tIH INC HIGH Period 250 - - ns tIC INC Inactive to CS Inactive 1 - - ms tCPH CS Deselect Time (NO STORE) 100 - - ns tCPH CS Deselect Time (STORE) 10 - - ms INC to VOUT Change - 1 5 ms INC Cycle Time 1 - - ms INC Input Rise and Fall Time - - 500 ms Power-up to Wiper Stable - - 1 ms Store Cycle - 5 10 ms tIW tCYC tR, tF (Note 8) tPU (Note 8) tWR 7. Typical values are for TA = 25C and nominal supply voltage. 8. This parameter is periodically sampled and not 100% tested. 9. MI in the A.C. Timing diagram refers to the minimum incremental change in the W output due to a change in the wiper position. CS tCI tIL tCYC tIC tIH (store) tCPH 90% INC 90% 10% tDI tID tF U/D tR MI(3) tIW RWB Figure 4. A.C. Timing http://onsemi.com 6 CAT5111 APPLICATIONS INFORMATION (a) resistive divider (b) variable resistance (c) two-port Figure 5. Potentiometer Configuration Applications 1 R3 R4 - +5 V 8 Digital POT 2 1 7 + +5 V 4A 9 - 3 10 8 + 11 R2 R1 R2 2 1 7 +5 V 8 Digital POT 2 +5 V R1 RA 6 4 VO RB 6 5 - R4 R3 7 + 0.01 mF 2 1 0.01 mF Figure 7. Programmable Sq. Wave Oscillator (555) +5 V +200 mV 8 4 5 0.01 mF 0.003 mF C 7 Digital POT 10 kW 3 6 IC3A 74HC132 2 1 7 8 555 +2.5 V A1 = A2 = A3 = 1/4 LM6064 R2 = R3 = R4 = 5 kW RPOT = 10 kW OSC 4 R2 Figure 6. Programmable Instrumentation Amplifier 1/ 4 7 5 (1-p)R POT 3 4 CAT5113/5114 V2 (+) pRPOT 20 kW + IC1B 499 kW CS CAT5111/5112 IC2 5 2 +5 V 4 - 3 + 1 11 IC1A Sensor -5 V 499 kW 499 kW VSENSOR = 1 V 50 mV Figure 8. Sensor Auto Referencing Circuit http://onsemi.com 7 VREF = 1 V 499 kW VCORR - 6 + 3 - V1 (-) VOUT = 1 V 1 mV CAT5111 VOUT R1 11 kW 2952 SHUTDOWN SD GND 1.23 V FB 6 2 3 R3 10 kW 6 5 CAT5113/5114 4 3 IS IC1 393 - IC2 74HC132 1 OSC CLO CHI 7 Digital POT + 4 - 0.1 mF IC3 CAT5111/5112 +5 V 8 2 10 kW 1 7 + 10 kW 2 + 5 3 VS +2.5 V A1 3 6 4 C1 0.001 mF R2 6 1 mF R3 +5 V VUL 2 1 7 50 kW +5 V 8 +5 V 7 - + 4 A2 AI IC4 +2.5 V VO 0.001 mF R2 10 kW R3 100 kW +5 V 2 7 - 3 + 4 R1 100 kW +5 V - R1 100 kW VS 2 + +2.5 V R1 100 kW CAT5111/5112 3 +5 V - + R 2.5 kW 4 11 IS 1 R1 100 kW 7 A2 Figure 13. Programmable Current Source/Sink http://onsemi.com 8 A1 Figure 12. Programmable Bandpass Filter Figure 11. Automatic Gain Control Serial Bus VO 6 +2.5 V 0 VS 2.5 V +5 V VO 6 CAT5113/5114 4 0 VO 2.5 V C2 R1 VS - + 2 10 k Figure 10. Programmable I to V Converter +5 V 6 3 5 R1 VLL 3 5 +5 V 7 - 1 MW 330 W LT1097 Figure 9. Programmable Voltage Regulator +5 V pR (1-p)R 330 W - Digital POT 0.1 mF 6.8 mF R2 820 W 1 mF +5 V 8 4 + 2 1 7 VO (REG) CAT5113/5114 Digital POT VIN (UNREG) 2 1 7 +5 V 8 Digital POT 100 kW 5 +2.5 V 6 A1 = A2 = LMC6064A CAT5111 Table 7. ORDERING INFORMATION Orderable Part Number Resistance (kW) CAT5111LI-10-G 10 CAT5111LI-50-G 50 CAT5111LI-00-G 100 CAT5111VI-10-GT3 10 CAT5111VI-50-GT3 50 CAT5111VI-00-GT3 100 CAT5111YI-10-GT3 10 CAT5111YI-50-GT3 50 CAT5111YI-00-GT3 100 CAT5111ZI-10-T3 10 CAT5111ZI-50-T3 50 CAT5111ZI-00-T3 100 Lead Finish Package-Pins Shipping NiPdAu PDIP-8 (Pb-Free) 50 Units / Tube NiPdAu SOIC-8 (Pb-Free) 3000 / Tape & Reel NiPdAu TSSOP-8 (Pb-Free) 3000 / Tape & Reel Matte-Tin MSOP-8 (Pb-Free) 3000 / Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. 10. For detailed information and a breakdown of device nomenclature and numbering systems, please see the ON Semiconductor Device Nomenclature document, TND310/D, available at www.onsemi.com. 11. All packages are RoHS compliant. 12. Standard lead finish is NiPdAu, except MSOP package is Matte-Tin. 13. Contact factory for Matte-Tin finish availability for PDIP, SOIC and TSSOP packages. http://onsemi.com 9 CAT5111 PACKAGE DIMENSIONS PDIP-8, 300 mils CASE 646AA ISSUE A SYMBOL MIN NOM A E1 5.33 A1 0.38 A2 2.92 3.30 4.95 b 0.36 0.46 0.56 b2 1.14 1.52 1.78 c 0.20 0.25 0.36 D 9.02 9.27 10.16 E 7.62 7.87 8.25 E1 6.10 6.35 7.11 e PIN # 1 IDENTIFICATION MAX 2.54 BSC eB 7.87 L 2.92 10.92 3.30 3.80 D TOP VIEW E A2 A A1 c b2 L e eB b SIDE VIEW END VIEW Notes: (1) All dimensions are in millimeters. (2) Complies with JEDEC MS-001. http://onsemi.com 10 CAT5111 PACKAGE DIMENSIONS SOIC 8, 150 mils CASE 751BD ISSUE O E1 E SYMBOL MIN A 1.35 1.75 A1 0.10 0.25 b 0.33 0.51 c 0.19 0.25 D 4.80 5.00 E 5.80 6.20 E1 3.80 MAX 4.00 1.27 BSC e PIN # 1 IDENTIFICATION NOM h 0.25 0.50 L 0.40 1.27 0 8 TOP VIEW D h A1 A c e b L END VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MS-012. http://onsemi.com 11 CAT5111 PACKAGE DIMENSIONS TSSOP8, 4.4x3 CASE 948AL ISSUE O b SYMBOL MIN NOM 1.20 A E1 E MAX A1 0.05 A2 0.80 b 0.19 0.15 0.90 1.05 0.30 c 0.09 D 2.90 3.00 3.10 E 6.30 6.40 6.50 E1 4.30 4.40 4.50 0.20 0.65 BSC e L 1.00 REF L1 0.50 0 0.60 0.75 8 e TOP VIEW D A2 c q1 A A1 L1 SIDE VIEW L END VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MO-153. http://onsemi.com 12 CAT5111 PACKAGE DIMENSIONS MSOP 8, 3x3 CASE 846AD ISSUE O SYMBOL MIN NOM MAX 1.10 A E A1 0.05 0.10 0.15 A2 0.75 0.85 0.95 b 0.22 0.38 c 0.13 0.23 D 2.90 3.00 3.10 E 4.80 4.90 5.00 E1 2.90 3.00 3.10 E1 0.65 BSC e L 0.60 0.40 0.80 L1 0.95 REF L2 0.25 BSC 0 6 TOP VIEW D A A2 A1 DETAIL A e b c SIDE VIEW END VIEW q L2 Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MO-187. L L1 DETAIL A http://onsemi.com 13 CAT5111 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5817-1050 http://onsemi.com 14 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative CAT5111/D Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: ON Semiconductor: CAT5111VI-50-GT3 CAT5111LI-10-G CAT5111VI-00-GT3 CAT5111VI-10-G CAT5111LI-50-G CAT5111ZI-50-T3 CAT5111ZI-00-T3 CAT5111ZI-10-T3 CAT5111VI-10-GT3 CAT5111LI-00-G CAT5111YI-00-GT3 CAT5111YI-10-GT3 CAT5111YI-50-GT3 CAT5111VI-00-G