A1171 Micropower Ultrasensitive Hall Effect Switch Features and Benefits Description The A1171 integrated circuit is an ultrasensitive, Hall effect switch with latched digital outputs and either unipolar or omnipolar magnetic actuation. It features operation at low supply currents and voltages, making it ideal for batteryoperated electronics. The low operating supply voltage, 1.65 to 3.5 V, and unique clocking algorithm assist in reducing the average operating power consumption. For example, the power requirement is less than 15 W with a 2.75 V supply. 1.65 to 3.5 V battery operation Low supply current High sensitivity, BOP typically 30 G (3.0 mT) Operation with either north or south pole Configurable unipolar or omnipolar magnetic sensing Complementary, push-pull outputs Chopper stabilized Superior temperature stability Extremely low switchpoint drift Insensitive to physical stress Solid state reliability Small size Package: 6 pin DFN/MLP (suffix EW) Unlike more traditional Hall effect switches, the A1171 allows the user to configure how the device is magnetically actuated. Under default conditions the device activates output switching with either a north or south polarity magnetic field of sufficient strength. The magnetic actuation can be set via an external selection pin to operate in a unipolar mode, switching only on a north or south polarity but not both. Furthermore, the output of the A1171 can be configured to switch either off or on in the absence of any significant magnetic field. Lastly, the A1171 has two push-pull output structures. This polarity-independence, as well as the minimal power requirements, allows the A1171 to easily replace reed switches, Continued on the next page... Not to scale Functional Block Diagram VDD Clock / Logic Low-Pass Filter GND 1171-DS, Rev. 5 Logic Amp Sample and Hold and Averaging Dynamic Offset Cancellation VOUTPS Latch VOUTPN Latch SELECT A1171 Micropower Ultrasensitive Hall Effect Switch Description (continued) providing superior reliability and ease of manufacturing while eliminating the requirement for signal conditioning. silicon chip, a Hall-voltage generator, a small-signal amplifier, chopper stabilization, a latch, and a MOSFET output. Improved stability is made possible through dynamic offset cancellation using chopper stabilization, which reduces the residual offset voltage normally caused by device overmolding, temperature dependencies, and thermal stress. This device includes, on a single The A1171 device offers a magnetically optimized solution, suitable for most applications. Package type EW (0.40 mm maximum height) offers a leadless surface mount solution. It is lead (Pb) free, with NiPdAu leadframe plating. Selection Guide Part Number Packing1 Package A1171EEWLT-P2 1Contact Allegro(R) 2Allegro DFN/MLP 1.5x2 mm; 0.40 mm maximum height for additional packing options. 3000 pieces per 7 inch reel products sold in DFN package types are not intended for automotive applications. Absolute Maximum Ratings Characteristic Symbol Notes Rating Units 5 V Supply Voltage VDD Reverse Supply Voltage VRDD -0.3 V B Unlimited G VOUTPx 5 V VROUTPx -0.3 V IOUTPx(Source) 1 mA Magnetic Flux Density Output Off Voltage Reverse Output Voltage Output Current IOUTPx(Sink) -1 mA -40 to 85 C TJ(max) 165 C Tstg -65 to 170 C Operating Ambient Temperature TA Maximum Junction Temperature Storage Temperature Range E Terminal List Table Pin-out Diagram VOUTPS 1 VOUTPN 2 SELECT 3 6 VDD PAD 5 NC 4 GND Name Number Function VOUTPS 1 Push-pull output (selectable omnipolar activation or unipolar south pole activation) VOUTPN 2 Push-pull output (selectable inverted omnipolar activation or unipolar north pole activation) SELECT 3 Sets activation mode for VOUTPx outputs; omnipolar output when tied to VDD or floating, unipolar output when grounded GND 4 Ground NC 5 No connection VDD 6 Connects power supply to chip PAD - Exposed pad for enhanced thermal dissipation Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 2 A1171 Micropower Ultrasensitive Hall Effect Switch ELECTRICAL CHARACTERISTICS valid over operating voltage and temperature range (unless otherwise specified) Characteristic Supply Voltage Range2 Output Voltage Period Chopping Frequency Supply Slew Rate3 Supply Current VDD SELECT Voltage4 Typ.1 Max. Units Operating, TA= 25C 1.65 - 3.5 V Operating, over full ambient temperature range 1.8 100 300 mV - mV Test Conditions VOUT(SAT) NMOS on, ISINK = 1 mA, VDD = 2.75 V VOUT(HIGH) PMOS on, ISOURCE = -1 mA, VDD = 2.75 V - VDD-300 VDD-100 tPERIOD - 50 100 ms fC - 200 - kHz 20 - - V/ms IDD(EN) SR Device in awake mode (enabled) - - 2.0 mA IDD(DIS) Device in sleep mode (disabled) - - 8.0 A VDD = 1.8 V, TA = 25C - 3.5 8 A VDD = 3.5 V, TA = 25C IDD(AV) SELECT Current4 Min. Symbol - 7.1 12 A ISELECT 0 1 2 A VSELECT(LOW) 0 - 1/ V 3 DD V VSELECT(HIGH) 2/ V 3 DD - VDD V 1Typical data are for initial design estimations only, and assume optimum manufacturing and application conditions, such as TA = 25C. Performance may vary for individual units, within the specified maximum and minimum limits. 2Operate points, B OPX, and release points, BRPX, vary with supply voltage. 3If SR < SR(min), then valid device output might be delayed for one Period, t PERIOD , of device. 4Maximum V , minimum 0 V. DD MAGNETIC CHARACTERISTICS valid at 1.8 V VDD 3.5 V and TA = 25C Characteristic Operate Point3 Release Point3 Hysteresis Symbol Test Conditions Min. Typ.1 Max. Units2 BOPS - 32 55 G BOPN -55 -32 - G BRPS 6 26 - G BRPN - -26 -6 G - 6 - G BHYS |BOPX - BRPX| 1Typical data are for initial design estimations only, and assume optimum manufacturing and application conditions, such as TA = 25C. Performance may vary for individual units, within the specified maximum and minimum limits. 21 gauss (G) is exactly equal to 0.1 millitesla (mT). 3Operate points, B OPX, and release points, BRPX, vary with supply voltage. Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 3 A1171 Micropower Ultrasensitive Hall Effect Switch THERMAL CHARACTERISTICS may require derating at maximum conditions, see application information Characteristic Symbol Package Thermal Resistance Test Conditions* 2-layer PCB, with 0.23 RJA in.2 copper area each side 4-layer PCB, based on JEDEC standard Value Units 125 C/W 64 C/W *Additional thermal information available on Allegro Web site. Power Dissipation versus Ambient Temperature 3000 2750 2500 Power Dissipation, PD (mW) 2250 2000 EW package 4-layer PCB (RJA = 64 C/W) 1750 1500 1250 EW package 2-layer PCB (RJA = 125 C/W) 1000 750 500 250 0 20 40 60 80 100 120 Temperature (C) 140 160 180 Output Polarity Diagram +B (South) Magnetic Field 0 -B (North) (Omnipolar configuration) Output Pin (Activation Polarity) VOUTPS VOUTPN (South) VOUTPS (Unipolar configuration) (North) VOUTPN Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 4 A1171 Micropower Ultrasensitive Hall Effect Switch Functional Description Low Average Power Internal timing circuitry activates the IC for a short period of time, tAwake, and deactivates it for the remainder of the period (tPeriod). A short awake state duration allows stabilization prior to the sampling and data-latching on the falling edge of the timing pulse. The output during the sleep state is latched in the last sampled state. The supply current is not affected by the output state. VOUTPN operates with the opposite output polarity. That is, the output is low (on) in the absence of a magnetic field. The output goes high (turns off) when sufficient field, or either north or south polarity, is presented to the device. tPeriod Awake The difference between the magnetic operate and release points is the hysteresis, BHYS , of the device. This built-in hysteresis allows clean switching of the output even in the presence of external mechanical vibration and electrical noise. Sleep I DD(DIS) 0 Powering-on the device in a hysteresis region, between BOPX and BRPX, allows an indeterminate output state. The correct state is attained after the first excursion beyond BOPX or BRPX. Sample and Output Latched (A) VOUTPS (B) VOUTPN Switch to High VOUT(HIGH) VOUT Switch to Low VOUT V+ Switch to Low Switch to Low Switch to Low Switch to High VOUT(HIGH) Switch to High V+ Switch to High I DD(EN) Operation The VOUTPS output switches low (turns on) when the magnetic field received at the Hall element in the A1171 exceeds the operate point, BOPS (or is less than BOPN). After turn-on, the output voltage is VOUT(SAT). The output transistor is capable of sinking current up to the short circuit current limit, IOM. When the magnetic field is reduced below the release point, BRPS (or increased above BRPN), the device output switches high (turns off). The pull-up transistor brings the output voltage to VOUT(HIGH). VOUT(SAT) BHYS 0 BRPS BRPS BRPN B- BOPS BHYS B+ BOPN BHYS 0 BOPS BOPN B- VOUT(SAT) 0 BRPN 0 B+ BHYS Figure 1. Switching Behavior of Omnipolar Switches. On the horizontal axis, the B+ direction indicates increasing south polarity magnetic field strength, and the B- direction indicates decreasing south polarity field strength (including the case of increasing north polarity). This output switching profile applies when the SELECT line is allowed to float, selecting omnipolar operation. Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 5 A1171 Micropower Ultrasensitive Hall Effect Switch (A) VOUTPN (B) VOUTPS V+ V+ Switch to High VOUT VOUT VOUT(HIGH) Switch to Low Switch to Low Switch to High VOUT(HIGH) VOUT(SAT) BRPN 0 B+ BHYS B- 0 BOPS BOPN B- VOUT(SAT) 0 BRPS 0 B+ BHYS Figure 2. Operation with Unipolar Mode Selected (SELECT Pin Grounded) SELECT Pin Settings Effect on Output Output Pin Number 1 2 Name SELECT Pin Configuration Output Description Tied to VDD or floating Omnipolar output; ON with magnetic field of sufficient strength (B < BOPN or B > BOPS); OFF with low-strength or no magnetic field (BRPN < B < BRPS) Tied to ground Unipolar output; ON with south polarity magnetic field of sufficient strength (B > BOPS) Tied to VDD or floating Omnipolar output; OFF with magnetic field of sufficient strength (B < BOPN or B > BOPS); ON with low-strength or no magnetic field (BRPN < B < BRPS) Tied to ground Unipolar output; ON with north polarity magnetic field of sufficient strength (B < BOPN) VOUTPS VOUTPN Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 6 A1171 Micropower Ultrasensitive Hall Effect Switch Applications It is strongly recommended that an external bypass capacitor be connected (in close proximity to the Hall element) between the supply and ground of the device to reduce both external noise and noise generated by the chopper stabilization technique. As is shown in figure 3, a 0.1F capacitor is typical. * Hall-Effect IC Applications Guide, AN27701 Extensive applications information on magnets and Hall-effect devices is available in the following notes: All are provided in Allegro Electronic Data Book, AMS-702, and on the Allegro Web site, www.allegromicro.com. * Hall-Effect Devices: Gluing, Potting, Encapsulating, Lead Welding and Lead Forming AN27703.1 * Soldering Methods for Allegro Products (SMD and ThroughHole), AN26009 VS VS VOUTPS CBYP 0.1 F Outputs A1171 VOUTPS VDD VOUTPN NC SELECT GND CBYP 0.1 F (a) Outputs A1171 VDD VOUTPN NC SELECT GND (b) Figure 3. Typical Application Circuits: (a) Omnipolar operation, and (b) Unipolar Operation Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 7 A1171 Micropower Ultrasensitive Hall Effect Switch Chopper Stabilization Technique When using Hall-effect technology, a limiting factor for switchpoint accuracy is the small signal voltage developed across the Hall element. This voltage is disproportionally small relative to the offset that can be produced at the output of the Hall element. This makes it difficult to process the signal while maintaining an accurate, reliable output over the specified operating temperature and voltage ranges. Chopper stabilization is a unique approach used to minimize Hall offset on the chip. The patented Allegro technique, namely Dynamic Quadrature Offset Cancellation, removes key sources of the output drift induced by thermal and mechanical stresses. This offset reduction technique is based on a signal modulationdemodulation process. The undesired offset signal is separated from the magnetic field-induced signal in the frequency domain, through modulation. The subsequent demodulation acts as a modulation process for the offset, causing the magnetic field induced signal to recover its original spectrum at baseband, while the dc offset becomes a high-frequency signal. The magnetic sourced signal then can pass through a low-pass filter, while the modulated dc offset is suppressed. This configuration is illustrated in figure 4. The chopper stabilization technique uses a high frequency clock. For demodulation process, a sample and hold technique is used, where the sampling is performed at twice the chopper frequency. This high-frequency operation allows a greater sampling rate, which results in higher accuracy and faster signal-processing capability. This approach desensitizes the chip to the effects of thermal and mechanical stresses, and produces devices that have extremely stable quiescent Hall output voltages and precise recoverability after temperature cycling. The repeatability of magnetic field-induced switching is affected slightly by a chopper technique. However, the Allegro high frequency chopping approach minimizes the affect of jitter and makes it imperceptible in most applications. Applications that are more likely to be sensitive to such degradation are those requiring precise sensing of alternating magnetic fields; for example, speed sensing of ring-magnet targets. For such applications, Allegro recommends its digital device families with lower sensitivity to jitter. For more information on those devices, contact your Allegro sales representative. Regulator Amp Low-Pass Filter Hall Element Sample and Hold Clock/Logic Figure 4. Chopper Stabilization Circuit (Dynamic Quadrature Offset Cancellation) Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 8 A1171 Micropower Ultrasensitive Hall Effect Switch Package EW, 6-pin DFN/MLP 1.50 0.15 0.75 F E 6 0.50 0.30 6 1.00 F 2.00 0.15 A 0.70 1.575 F 1 1 0.325 1.10 7X D SEATING PLANE 0.08 C C C PCB Layout Reference View 0.38 0.02 0.50 BSC B +0.055 0.325 -0.045 0.70 0.10 NN YWW 0.25 0.05 1 1 1.25 0.05 G Standard Branding Reference View N = Last two digits of device part number Y = Last digit of year of manufacture W = Week of manufacture 6 1.10 0.10 For Reference Only, not for tooling use (refernce DWG-2856; similar to JEDEC Type 1, MO-229X2BCD) Dimensions in millimeters Exact case and lead configuration at supplier discretion within limits shown A Terminal #1 mark area B Exposed thermal pad (reference only, terminal #1 identifier appearance at supplier discretion) C Reference land pattern layout (reference IPC7351 SON50P200X200X100-9M); All pads a minimum of 0.20 mm from all adjacent pads; adjust as necessary to meet application process requirements and PCB layout tolerances; when mounting on a multilayer PCB, thermal vias at the exposed thermal pad land can improve thermal dissipation (reference EIA/JEDEC Standard JESD51-5) D Coplanarity includes exposed thermal pad and terminals E Active Area Depth 0.15 mm REF F Hall Element (not to scale) G Branding scale and appearance at supplier discretion Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 9 A1171 Micropower Ultrasensitive Hall Effect Switch Revision History Revision Revision Date Rev. 5 October 26, 2011 Description of Revision Update Selection Guide Copyright (c)2005-2011, Allegro MicroSystems, Inc. Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. Allegro's products are not to be used in life support devices or systems, if a failure of an Allegro product can reasonably be expected to cause the failure of that life support device or system, or to affect the safety or effectiveness of that device or system. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringement of patents or other rights of third parties which may result from its use. For the latest version of this document, visit our website: www.allegromicro.com Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 10