IDT72401 IDT72402 IDT72403 IDT72404 CMOS PARALLEL FIFO 64 x 4-BIT AND 64 x 5-BIT Integrated Device Technology, Inc. FEATURES: * * * * * * * * * * * * * * * * * * First-ln/First-Out Dual-Port memory 64 x 4 organization (IDT72401/03) 64 x 5 organization (IDT72402/04) IDT72401/02 pin and functionally compatible with MMI67401/02 RAM-based FIFO with low falI-through time Low-power consumption -- Active: 175mW (typ.) Maximum shift rate -- 45MHz High data output drive capability Asynchronous and simultaneous read and write Fully expandable by bit width Fully expandable by word depth IDT72403/04 have Output Enable pin to enable output data High-speed data communications applications High-performance CMOS technology Available in CERDIP, plastic DIP and SOIC Military product compliant to MlL-STD-883, Class B Standard Military Drawing #5962-86846 and 5962-89523 is listed on this function. Industrial temperature range (-40C to +85C) is available, tested to military electrical specifications DESCRIPTION: The IDT72401 and IDT72403 are asynchronous highperformance First-ln/First-Out memories organized 64 words by 4 bits. The IDT72402 and IDT72404 are asynchronous high-performance First-ln/First-Out memories organized as 64 words by 5 bits. The IDT72403 and IDT72404 also have an Output Enable (OE) pin. The FlFOs accept 4-bit or 5-bit data at the data input (D0-D3, 4). The stored data stack up on a firstin/first-out basis. A Shift Out (SO) signal causes the data at the next to last word to be shifted to the output while all other data shifts down one location in the stack. The Input Ready (IR) signal acts like a flag to indicate when the input is ready for new data (IR = HIGH) or to signal when the FIFO is full (IR = LOW). The Input Ready signal can also be used to cascade multiple devices together. The Output Ready (OR) signal is a flag to indicate that the output remains valid data (OR = HIGH) or to indicate that the FIFO is empty (OR = LOW). The Output Ready can also be used to cascade multiple devices together. Width expansion is accomplished by logically ANDing the Input Ready (IR) and Output Ready (OR) signals to form composite signals. Depth expansion is accomplished by tying the data inputs of one device to the data outputs of the previous device. The Input Ready pin of the receiving device is connected to the Shift Out pin of the sending device and the Output Ready pin of the sending device is connected to the Shift In pin of the receiving device. Reading and writing operations are completely asynchronous allowing the FIFO to be used as a buffer between two digital machines of widely varying operating frequencies. The 45MHz speed makes these FlFOs ideal for high-speed communication and controller applications. Military grade product is manufactured in compliance with the latest revision of MIL-STD-883, Class B. FUNCTIONAL BLOCK DIAGRAM SI IR INPUT CONTROL LOGIC WRITE MULTIPLEXER DATA IN MEMORY ARRAY D 0-3 D4 (IDT72402 and IDT72404) MR MASTER RESET WRITE POINTER OUTPUT ENABLE DATA OUT Q 0-3 Q 4 (IDT72402 and IDT72404) READ MULTIPLEXER READ POINTER OE (IDT72403 and IDT72404) OUTPUT CONTROL LOGIC SO OR 2747 drw 01 The IDT logo is a registered trademark of Integrated Device Technology, Inc. FAST is a trademark of National Semiconductor, Inc. MILITARY AND COMMERCIAL TEMPERATURE RANGES 1996 Integrated Device Technology, Inc. For latest information contact IDT's web site at www.idt.com or fax-on-demand at 408-492-8391. 5.01 SEPTEMBER 1996 DSC-2747/7 1 IDT72401, IDT72402, IDT72403, IDT72404 CMOS PARALLEL FIFO 64 x 4-BIT AND 64 x 5-BIT MILITARY AND COMMERCIAL TEMPERATURE RANGES PIN CONFIGURATIONS IDT72401/IDT72403 NC/OE(1) IR SI D0 D1 D2 D3 GND 1 16 2 15 3 4 5 P16-1, D16-1 & S016-1 14 13 12 6 11 7 10 8 9 DIP/SOIC TOP VIEW (IDT72404 Only) IDT72402/IDT72404 Vcc SO OR Q0 Q1 Q2 Q3 MR 2747 drw 02 NC/OE(2) IR SI D0 D1 D2 D3 D4 GND 1 18 2 17 3 16 4 15 P18-1, D18-1 & S018-1 5 6 7 Vcc SO OR Q0 Q1 Q2 Q3 Q4 MR 14 13 12 8 11 9 10 OE NC IR SI D0 D1 D2 D3 D4 GND 2747 drw 03 DIP/SOIC TOP VIEW 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 Vcc NC SO OR Q0 Q1 Q2 Q3 Q4 MR 2747 drw 04 CERPACK TOP VIEW NOTES: 1. Pin 1: NC - No Connection IDT72401, OE - IDT72403 2. Pin 1: NC - No Connection IDT72402,OE - IDT72404 ABSOLUTE MAXIMUM RATINGS(1) RECOMMENDED OPERATING CONDITIONS Symbol Rating Commercial Military Unit Symbol Parameter Min. Typ. VTERM Terminal Voltage with Respect to GND -0.5 to +7.0 -0.5 to +7.0 V VCC VCC Mil. Supply Voltage Com'l. Supply Voltage 4.5 4.5 5.0 5.0 Supply Voltage 0 Operating Temp. Temperature Under Bias 0 to +70 -55 to +125 -55 to +125 -65 to +135 C C GND TA TBIAS VIH Input High Voltage 2.0 VIL(1) Input High Voltage -- -- 0.8 TSTG IOUT Storage Temp. DC Output Current -55 to +125 50 -65 to +150 50 Max. Unit 5.5 5.5 V V 0 0 V -- -- V NOTE: 1. 1.5V undershoots are allowed for 10ns once per cycle. C mA NOTE: 2747 tbl 01 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. V 2747 tbl 02 CAPACITANCE (TA = +25C, f = 1.0MHz) Parameter(1) Symbol Conditions Max. Unit CIN Input Capacitance VIN = 0V 5 pF COUT Output Capacitance VOUT = 0V 7 pF NOTE: 1. This parameter is sampled and not 100% tested. 2747 tbl 03 DC ELECTRICAL CHARACTERISTICS (Commercial: VCC = 5.0V 10%, TA = 0C to +70C; Military: VCC = 5.0V 10%, TA = -55C to +125C) Symbol Parameter Test Conditions Min. Max. Unit -- A IIL Low-Level Input Current VCC = Max., GND VI VCC -10 IIH High-Level Input Current VCC = Max., GND VI VCC -- 10 A VOL Low-Level Output Voltage VCC = Min., IOL = 8mA -- 0.4 V VOH High-Level Output Voltage VCC = Min., IOH = -4mA 2.4 -- V Output Short-Circuit Current VCC = Max., VO = GND -20 -110 mA Off-State Output Current VCC = Max., VO = 2.4V -- 20 A (IDT72403 and IDT72404) VCC = Max., VO = 0.4V -20 -- A Supply Current VCC = Max., f = 10MHz -- -- 35 45 mA mA IOS (1) IHZ ILZ ICC (2,3) Com'l. Military NOTES: 2747 tbl 1. Not more than one output should be shorted at a time and duration of the short-circuit should not exceed one second. Guaranteed but not tested. 2. ICC measurements are made with outputs open. OE is HIGH for IDT72403/72404. 3 For frequencies greater than 10MHZ, ICC = 35mA + (1.5mA x [f - 10MHz]) commercial, and ICC = 45mA + (1.5mA x [f - 10MHz]) military. 5.01 2 04 IDT72401, IDT72402, IDT72403, IDT72404 CMOS PARALLEL FIFO 64 x 4-BIT AND 64 x 5-BIT MILITARY AND COMMERCIAL TEMPERATURE RANGES OPERATING CONDITIONS (Commercial: VCC = 5.0V 10%, TA = 0C to +70C; Military: VCC = 5.0V 10%, TA = -55C to +125C) Symbol Parameters FIgure Commercial IDT72401L45 IDT72402L45 IDT72403L45 IDT72404L45 Min. Max. IDT72401L35 IDT72402L35 IDT72403L35 IDT72404L35 Min. Max. Military and Commercial IDT72401L25 IDT72401L15 IDT72402L25 IDT72402L15 IDT72403L25 IDT72403L15 IDT72404L25 IDT72404L15 Min. Max. Min. Max. IDT72401L10 IDT72402L10 IDT72403L10 IDT72404L10 Min. Max. Unit tSIH(1) Shift in HIGH Time 2 9 -- 9 -- 11 -- 11 -- 11 -- ns tSIL Shift in LOW TIme 2 11 -- 17 -- 24 -- 25 -- 30 -- ns tIDS Input Data Set-up 2 0 -- 0 -- 0 -- 0 -- 0 -- ns tIDH Input Data Hold Time 2 13 -- 15 -- 20 -- 30 -- 40 -- ns tSOH(1) Shift Out HIGH Time 5 9 -- 9 -- 11 -- 11 -- 11 -- ns tSOL Shift Out LOW Time 5 11 -- 17 -- 24 -- 25 -- 25 -- ns tMRW Master Reset Pulse 8 20 -- 25 -- 25 -- 25 -- 30 -- ns tMRS Master Reset Pulse to SI 8 10 -- 10 -- 10 -- 25 -- 35 -- ns tSIR Data Set-up to IR 4 3 -- 3 -- 5 -- 5 -- 5 -- ns tHIR Data Hold from IR 4 13 -- 15 -- 20 -- 30 -- 30 -- ns tSOR(4) Data Set-up to OR HIGH 7 0 -- 0 -- 0 -- 0 -- 0 -- ns 2747 tbl 05 AC ELECTRICAL CHARACTERISTICS (Commercial: VCC = 5.0V 10%, TA = 0C to +70C; Military: VCC = 5.0V 10%, TA = -55C to +125C) Symbol Parameters FIgure Commercial IDT72401L45 IDT72402L45 IDT72403L45 IDT72404L45 Min. Max. IDT72401L35 IDT72402L35 IDT72403L35 IDT72404L35 Min. Max. Military and Commercial IDT72401L25 IDT72401L15 IDT72402L25 IDT72402L15 IDT72403L25 IDT72403L15 IDT72404L25 IDT72404L15 Min. Max. Min. Max. IDT72401L10 IDT72402L10 IDT72403L10 IDT72404L10 Min. Max. Unit tIN Shift In Rate 2 -- 45 -- 35 -- 25 -- 15 -- 10 MHz tIRL(1) Shift In to Input Ready LOW 2 -- 18 -- 18 -- 21 -- 35 -- 40 ns tIRH(1) Shift In to Input Ready HIGH 2 -- 18 -- 20 -- 28 -- 40 -- 45 ns tOUT Shift Out Rate 5 -- 45 -- 35 -- 25 -- 15 -- 10 MHz Shift Out to Output Ready LOW 5 -- 18 -- 18 -- 19 -- 35 -- 40 ns ns tORL(1) (1) Shift Out to Output Ready HIGH 5 -- 19 -- 20 -- 34 -- 40 -- 55 tODH Output Data Hold (Previous Word) 5 5 -- 5 -- 5 -- 5 -- 5 -- ns tODS Output Data Shift (Next Word) 5 -- 19 -- 20 -- 34 -- 40 -- 55 ns tPT Data Throughput or "Fall-Through" 4, 7 -- 30 -- 34 -- 40 -- 65 -- 65 ns tMRORL Master Reset to OR LOW 8 -- 25 -- 28 -- 35 -- 35 -- 40 ns tMRIRH Master Reset to IR HIGH 8 -- 25 -- 28 -- 35 -- 35 -- 40 ns tMRQ Master Reset to Data Output LOW 8 -- 20 -- 20 -- 25 -- 35 -- 40 ns tOOE(3) Output Valid from OE LOW 9 -- 12 -- 15 -- 20 -- 30 -- 35 ns tHZOE(3,4) Output High-Z from OE HIGH 9 -- 12 -- 12 -- 15 -- 25 -- 30 ns Input Ready Pulse HIGH 4 9 -- 9 -- 11 -- 11 -- 11 -- ns Ouput Ready Pulse HIGH 7 9 -- 9 -- 11 -- 11 -- 11 -- ns tORH tIPH (2,4) tOPH(2,4) NOTES: 2747 tbl 06 1. Since the FIFO is a very high-speed device, care must be excercised in the design of the hardware and timing utilized within the design. Device grounding and decoupling are crucial to correct operation as the FIFO will respond to very small glitches due to long reflective lines, high capacitances and/or poor supply decoupling and grounding. A monolithic ceramic capacitor of 0.1F directly between VCC and GND with very short lead length is recommended. 2. This parameter applies to FIFOs communicating with each other in a cascaded mode. IDT FIFOs are guaranteed to cascade with other IDT FIFOs of like speed grades. 3. IDT72403 and IDT72404 only. 4. Guaranteed by design but not currently tested. 5.01 3 IDT72401, IDT72402, IDT72403, IDT72404 CMOS PARALLEL FIFO 64 x 4-BIT AND 64 x 5-BIT MILITARY AND COMMERCIAL TEMPERATURE RANGES AC TEST CONDITIONS Input Pulse Levels 5V GND to 3.0V Input Rise/Fall Times 3ns Input Timing Reference Levels 1.5V Output Reference Levels Output Load 560 1.5V OUTPUT See Figure 1 1.1K 2747 tbl 07 30pF* 2747 drw 06 ALL INPUT PULSES: or equivalent circuit 3.0V GND 90% 10% <3ns 90% 10% Figure 1. AC Test Load <3ns *Including scope and jig 2747 drw 05 SIGNAL DESCRIPTIONS OUTPUTS: INPUTS: DATA OUTPUT (Q0-3, 4) Data Output lines. The IDT72401 and IDT72403 have a 4bit data output. The IDT72402 and IDT72404 have a 5-bit data output. DATA INPUT (D0-3, 4) Data input lines. The IDT72401 and IDT72403 have a 4-bit data input. The IDT72402 and IDT72404 have a 5-bit data input. CONTROLS: SHIFT IN (SI) Shift In controls the input of the data into the FIFO. When SI is HIGH, data can be written to the FIFO via the D0-3, 4 lines. SHIFT OUT (SO) Shift Out controls the output of data of the FIFO. When SO is HIGH, data can be read from the FIFO via the Data Output (Q0-3, 4) lines. MASTER RESET (MR) Master Reset clears the FIFO of any data stored within. Upon power up, the FIFO should be cleared with a Master Reset. Master Reset is active LOW. INPUT READY (IR) When Input Ready is HIGH, the FIFO is ready for new input data to be written to it. When IR is LOW the FIFO is unavailable for new input data. Input Ready is also used to cascade many FlFOs together, as shown in Figures 10 and 11 in the Applications section. OUTPUT READY (OR) When Output Ready is HIGH, the output (Q0-3, 4) contains valid data. When OR is LOW, the FIFO is unavailable for new output data. Output Ready is also used to cascade many FlFOs together, as shown in Figures 10 and 11. FUNCTIONAL DESCRIPTION These 64 x 4 and 64 x 5 FIFOs are designed using a dual port RAM architecture as opposed to the traditional shift register approach. This FIFO architecture has a write pointer, a read pointer and control logic, which allow simultaneous read and write operations. The write pointer is incremented by the falling edge of the Shift In (Sl) control; the read pointer is incremented by the falling edge of the Shift Out (SO). The Input Ready (IR) signals when the FIFO has an available memory location; Output Ready (OR) signals when there is valid data on the output. Output Enable (OE) provides the capability of three-stating the FIFO outputs. FIFO Reset The FIFO must be reset upon power up using the Master Reset (MR) signal. This causes the FlFO to enter an empty state, signified by Output Ready (OR) being LOW and Input Ready (IR) being HIGH. In this state, the data outputs (Q0-3, 4) will be LOW. Data Input Data is shifted in on the LOW-to-HlGH transition of Shift In (Sl). This loads input data into the first word location of the FIFO and causes Input Ready to go LOW. On the HlGH-toLOW transition of Shift In, the write pointer is moved to the next word position and Input Ready (IR) goes HIGH, indicating the readiness to accept new data. If the FIFO is full, Input Ready will remain LOW until a word of data is shifted out. OUTPUT ENABLE (OE) (IDT72403 AND IDT72404 ONLY) Output enable is used to read FIFO data onto a bus. Output Enable is active LOW. 5.01 4 IDT72401, IDT72402, IDT72403, IDT72404 CMOS PARALLEL FIFO 64 x 4-BIT AND 64 x 5-BIT MILITARY AND COMMERCIAL TEMPERATURE RANGES Data Output Data is shifted out on the HlGH-to-LOW transition of Shift Out (SO). This causes the internal read pointer to be advanced to the next word location. If data is present, valid data will appear on the outputs and Output Ready (OR) will go HIGH. If data is not present, Output Ready will stay LOW indicating the FIFO is empty. The last valid word read from the FIFO will remain at the FlFOs output when it is empty. When the FIFO is not empty, Output Ready (OR) goes LOW on the LOW-to-HIGH transition of Shift Out. Previous data remains on the output until the HIGH-to-LOW transition of Shift Out (SO). Fall-Through Mode The FIFO operates in a fall-through mode when data gets shifted into an empty FIFO. After a fall-through delay the data propagates to the output. When the data reaches the output, the Output Ready (OR) goes HIGH. Fall-through mode also occurs when the FIFO is completely full. When data is shifted out of the full FIFO, a location is available for new data. After a fall-through delay, the Input Ready goes HIGH. If Shift In is HIGH, the new data can be written to the FIFO. Since these FlFOs are based on an internal dual-port RAM architecture with separate read and write pointers, the fallthrough time (tPT) is one cycle long. A word may be written into the FIFO on a clock cycle and can be accessed on the next clock cycle. TIMING DIAGRAMS 1/f IN t SIH SHIFT IN 1/f IN t SIL t IRH INPUT READY t IDH t IRL INPUT DATA t IDS 2747 drw 07 Figure 2. Input Timing (7) (2) SHIFT IN (4) (1) (5) (3) INPUT READY INPUT DATA (6) STABLE DATA 2747 drw 08 NOTES: 1. Input Ready HIGH indicates space is available and a Shift In pulse may be applied. 2. Input Data is loaded into the first word. 3. Input Ready goes LOW indicating the first word is full. 4. The write pointer is incremented. 5. The FIFO is ready for the next word. 6. If the FIFO is full then the Input Ready remains LOW. 7. Shift In pulses applied while Input Ready is LOW will be ignored (see Figure 4). Figure 3. The Mechanism of Shifting Data Into the FIFO 5.01 5 IDT72401, IDT72402, IDT72403, IDT72404 CMOS PARALLEL FIFO 64 x 4-BIT AND 64 x 5-BIT MILITARY AND COMMERCIAL TEMPERATURE RANGES TIMING DIAGRAMS (Continued) (2) SHIFT OUT (3) (5) SHIFT IN (4) INPUT READY t IPH tPT (1) t SIR t HIR STABLE DATA INPUT DATA 2747 drw 09 NOTES: 1. FIFO is initially full. 2. Shift Out pulse is applied. 3. Shift In is held HIGH. 4. As soon as Input Ready becomes HIGH the Input Data is loaded into the FIFO. 5. The write pointer is incremented. Shift In should not go LOW until (tPT + tIPH). Figure 4. Data is Shifted In Whenever Shift In and Input Ready are Both HIGH 1/fOUT t SOH SHIFT OUT 1/f OUT t SOL (2) t ORH OUTPUT READY t ODH t ODS OUTPUT DATA t ORL A-DATA B-DATA C-DATA (1) 2747 drw 10 NOTES: 1. This data is loaded consecutively A, B, C. 2. Data is shifted out when Shift Out makes a HIGH to LOW transition. Figure 5. Output TIming SHIFT OUT (7) (2) (4) (1) OUTPUT DATA (5) (3) OUTPUT READY (6) A-DATA B-DATA A or B 2747 drw 11 NOTES: 1. Output Ready HIGH indicates that data is available and a Shift Out pulse may be applied. 2. Shift Out goes HIGH causing the next step. 3. Output Ready goes LOW. 4. The read pointer is incremented. 5. Output Ready goes HIGH indicating that new data (B) is now available at the FIFO outputs. 6. If the FIFO has only one word loaded (A DATA) then Output Ready stays LOW and the A DATA remains unchanged at the outputs. 7. Shift Out pulses applied when Output Ready is LOW will be ignored. Figure 6. The Mechanism of Shifting Data Out of the FIFO 5.01 6 IDT72401, IDT72402, IDT72403, IDT72404 CMOS PARALLEL FIFO 64 x 4-BIT AND 64 x 5-BIT MILITARY AND COMMERCIAL TEMPERATURE RANGES TIMING DIAGRAMS (Continued) SHIFT IN SHIFT OUT tPT OUTPUT READY (1) t SOR t OPH DATA VALID DATA OUTPUT 2747 drw 12 NOTE: 1. FIFO initially empty. Figure 7. tPT and tOPH Specification - t MRW MASTER RESET t MRIRH INPUT READY (1) t MRORL (1) OUTPUT READY t MRS SHIFT IN t MRQ DATA OUTPUT 2747 drw 13 NOTE: 1. Worst case, FIFO initially full.. Figure 8. Master Reset Timing OUTPUT ENABLE t HZOE t OOE DATA OUT 2747 drw 14 NOTE: 1. High-Z transitions are referenced to the steady-state VOH -500mV and VOL +500mV levels on the output. tHZOE is tested with 5pF load capacitance instead of 30pF as shown in Figure 1. Figure 9. Output Enable Timing, IDT72403 and IDT72404 Only 5.01 7 IDT72401, IDT72402, IDT72403, IDT72404 CMOS PARALLEL FIFO 64 x 4-BIT AND 64 x 5-BIT MILITARY AND COMMERCIAL TEMPERATURE RANGES APPLICATIONS SI IR D0 D1 D2 D3 SHIFT IN INPUT READY DATA IN MR OR SO Q0 Q1 Q2 Q3 SI IR D0 D1 D2 D3 OUTPUT READY SHIFT OUT OR SO Q0 Q1 Q2 Q3 MR DATA OUT 2747 drw 15 MR NOTE: 1. FIFOs can be easily cascaded to any desired path. The handshaking and associated timing between the FIFOs are handled by the inherent timing of the devices. Figure 10. 128 x 4 Depth Expansion IR SI D0 D1 D2 D3 COMPOSITE INPUT READY SHIFT IN IR SI D0 D1 D2 D3 IR SI D0 D1 D2 D3 MR SO OR Q0 Q1 Q2 Q3 IR SI D0 D1 D2 D3 MR SO OR Q0 Q1 Q2 Q3 IR SI D0 D1 D2 D3 MR SO OR Q0 Q1 Q2 Q3 IR SI D0 D1 D2 D3 MR SO OR Q0 Q1 Q2 Q3 IR SI D0 D1 D2 D3 MR SO OR Q0 Q1 Q2 Q3 IR SI D0 D1 D2 D3 MR SO OR Q0 Q1 Q2 Q3 IR SI D0 D1 D2 D3 MR SO OR Q0 Q1 Q2 Q3 MR SO OR Q0 Q1 Q2 Q3 MR SO OR Q0 Q1 Q2 Q3 SHIFT OUT COMPOSITE OUTPUT READY MR 2747 drw 16 NOTES: 1. When the memory is empty, the last word will remain on the outputs until the Master Reset is strobed or a new data word falls through to the output. However, OR will remain LOW, indicating data at the output is not valid. 2. When the output data changes as a result of a pulse on SO, the OR signal always goes LOW before there is any change in output data and stays LOW until the new data has appeared on the outputs. Anytime OR is HIGH, there is valid stable data on the outputs. 3. If SO is held HIGH while the memory is empty and a word is written into the input, that word will appear at the output after a fall-through time. OR will go HIGH for one internal cycle (at least tORL) and then go back LOW again. The stored word will remain on the outputs. If more words are written into the FIFO, they will line up behind the first word and will not appear on the outputs until SO has been brought LOW. 4. When the Master Reset is brought Low, the outputs are cleared to LOW, IR goes HIGH and OR goes LOW. If SI is HIGH when the Master Reset goes HIGH, the data on the inputs will be written into the memory and IR will return to the LOW state until SI is brought LOW. If SI is LOW when the Master Reset is ended, IR will go HIGH, but the data in the inputs will not enter the memory until SI goes HIGH. 5. FIFOs are expandable on depth and width. However, in forming wider words, two external gates are required to generate composite Input and Output Ready flags. This is due to the variation of delays of the FIFOs. Figure 11. 192 x 12 Depth and Width Expansion 5.01 8 IDT72401, IDT72402, IDT72403, IDT72404 CMOS PARALLEL FIFO 64 x 4-BIT AND 64 x 5-BIT MILITARY AND COMMERCIAL TEMPERATURE RANGES ORDERING INFORMATION IDT XXXXX X X X X Device Type Power Speed Package Process/ Temperature Range 5.01 Blank Commercial (0C to+70C) B Military (-55C to+125C) Compliant to MIL-STD-883, Class B P D SO Plastic DIP (300 mils wide) Ceramic DIP (300 mils wide) Small Outline IC 45 35 25 15 10 Com'l. Only Com'l. and Mil Com'l. and Mil Com'l. and Mil Com'l. and Mil L Low Power 72401 72402 72403 72404 64 x 4 FIFO 64 x 5 FIFO 64 x 4 FIFO 64 x 5 FIFO Shift Frequency (fs) Speed in MHz 2747 drw 17 9